DIO-96/144
Language English
Version V1.2
Update Nov.2008
1 ………………………………………………
What’s on your package?
One DIO-96/144 card
One companion ISA CD (V2.1 or later)
One Quick Start Guide(this document)
2 ………………………………………………
Installing Windows Driver
Follow those steps:
1. Setup the Windows driver.
You can get the driver from:
CD:\NAPDOS\ISA\DIO\DLL\ http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/dio/dll/
- 1 -
Windows driver only support windows 98/NT/2000 and
XP/2003/vista 32-bit versions.
2. Click
3. Click
button to start installation.
button to install driver into the default folder.
4. Click button to continue installation.
5. Select “NO, I will restart my computer later” and then click button.
3 ………………………………………………
I/O Base Address/Interrupt Setting
The base address is set from SW1 DIP switch on board:
DIO-96 DIO-144
SW1
ON
■ ■ ■
■ ■ ■
1 2 3 4 5 6
A9 A8 A7 A6 A5 A4
SW1 Value Table (*):Default setting
I/O 1 2 3 4 5 6
Address A9 A8 A7 A6 A5 A4
200 1 0 0 0 0 0
210
…
1 0 0 0 0 1
。 . 。 。 。 。 。
2C0(*) 1 0 1 1 0 0
… 。 . 。 。 。 。 。
300
310
1
1
1
1
0
0
0
0
0
0
0
1
… … 。 . 。 。 。 。 。
3F0 1 1 1 1 1 1
SW1
ON
■ ■
■ ■ ■ ╳
1 2 3 4 5 6
A9 A8 A7 A6 A5 ╳
SW1 Value Table (*):Default setting
I/O 1 2 3 4 5 6
Address A9 A8 A7 A6 A5 X
200 1 0 0 0 0 X
220
…
1
。 .
0
。
0
。
0
。
1
。
X
X
2C0(*) 1 0 1 1 0 X
2E0
…
1 0 1 1 1 X
。 . 。 。 。 。 X
300 1 1 0 0 0 X
… … 。 . 。 。 。 。 X
3E0 1 1 1 1 1 X
The Interrupt Level Setting
- 2 -
4 ………………………………………………
Installing Hardware on PC
Follow those steps:
1. Shut down and power off your computer
2. Remove all covers from the computer
3. Select an empty ISA slot
4. Carefully insert your I/O card into the ISA slot
5. Replace the PC covers
6. Power on the computer
After powering-on the computer, continue next process.
5 ………………………………………………
Adding Hardware
Adding hardware is used on Windows 2000/XP/2003/Vista
32 only. Windows 9X/Me/NT users can skip it.
7. Add Hardware
7-1 Open the “Control Panel” by click the item “Start / Settings /
Control Panel”.
7-2 Double-click the item “Add/Remove Hardware” and Click the “Next
>” button .
7-3 Select the item “Add/Troubleshoot a device” and click the “ Next
>” button.
7-4 Select the item “Add a new device” and click the “Next >” button.
- 3 -
7-5 Select the item “No, I want to select the hardware from a list” and click the “Next >” button.
7-6 Select the item “Other device” and click the “Next >” button.
7-7 Click the “Have Disk…” button.
7-8 Click the “Browse…” button to select the Inf file default path is
C:\DAQPRO\DIO_Win2K\Inf and click the “OK” button.
7-9 Select the correct device from the “Models:” listbox and Click the
“Next >” button.
7-10 The windows show to dialog box and Click the “OK” button to enter the device’s properties settings.
8. Modify the device properties
1. Select Input/Output Range
2.
Click “Change Setting” to change I/O Range (Depend on
I/O Base Address)
No devices are conflicting
3.
Select Interrupt Request
4.
Click “Change Setting” to change
Interrupt Request. (Depend on
Interrupt Level setting)
9. Reboot the PC
No devices are conflicting
The detail “add hardware” information.
please refer to
CD:\NAPDOS\ISA\Manual\PCI_ISA_PnP_Driver_Installation_in_Win9x_2K_XP.pdf
- 4 -
6 ………………………………………………
Pin Assignments
CH0/1/2/3/4/5:50-pin header
CH5:The DIO-144 only
35
37
39
41
43
45
47
49
25
27
29
31
33
Pin Description Pin Description
1 PC7 2 GND
3
5
PC6
PC5
4
6
GND
GND
7
9
11
13
15
17
19
21
23
PC4
PC3
PC2
PC1
PC0
PB7
PB6
PB5
PB4
8
10
12
14
16
18
20
22
24
GND
GND
GND
GND
GND
GND
GND
GND
GND
PB3
PB2
PB1
PB0
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
+5V
26
28
30
32
34
36
38
40
42
44
46
48
50
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
TTL
High(1)
None
Defined
TTL
Low(0)
All signal are TTL compatible compatible
2.4V ~5.0V
(Voltages over 5.0V will damage the device)
2.4V~0.8V
Under 0.8V
- 5 -
7 ………………………………………………
Self-Test
I. Use CA-5002(Optional) to connect the CH0 with
CH1.
CH5
(DIO-144 only) CH4
34
CH3
4
CH2
3
CH1
2
CH0
II. Run the DIO sample program.
Get the file from(default path):
C:\DAQPro\DIO_WinXXX\Demo\
III. Check number of the DIO-96/144, and test DIO function
Please follow those steps:
- 6 -
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
One DIO-96/144 card had successfully installed to PC
Select the board number for the DIO-96/144.
It starts from 0.
Select the Ch No. to 1
1
4
5
Click this button to output the value
Click this button to input the value
Check the port A,B and C value.
If port A is 0, port B is FF and port C is 55.
The Test is pass!!!
2
3
6
Complet
- 7 -
8 ………………………………………………
Additional Information
DIO-96/144 Series Card Product page: http://www.icpdas.com/products/DAQ/pc_based/dio_96&144.htm
DN-37(Optional) page: http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
ADP-37(Optional) page: http://www.icpdas.com/products/DAQ/screw_terminal/adp_xx.htm
Documents:
CD:\NAPDOS\ISA\DIO\manual
CD:\NAPDOS\ISA\Manual http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/DIO/manual/
Software:
CD:\ ISA\NAPDOS\ISA\DIO http://www.icpdas.com/download/isa/dio/index.htm
The ICP DAS Web Site http://www.icpdas.com
Technical support
Supplies and ordering information
Ways to enhance your device
FAQ
Application story
Contact Us
[email protected]
Copyright ©2008 by ICP DAS Co., Ltd. All right are reserved
- 8 -
