TMC-10
Language English
Version V1.0
Update Nov.2008
1 ………………………………………………
What’s on your package?
One TMC-10 series card
One companion ISA CD (V2.1 or later)
One Quick Start Guide(This document)
2 ………………………………………………
Installing Windows Driver
Follow those steps:
1. Setup the Windows driver. You can get the driver from:
CD:\NAPDOS\ISA\TMC10\ http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/tmc10/
(The Windows NT driver have support the Windows 2K and windows
XP/2003/Vista 32bit version.)
Windows driver only support windows 98/NT/2000 and
XP/2003/vista 32-bit versions.
- 1 -
2. Click button to start installation.
3. Click button to install driver into the default folder.
4. Click button to continue installation.
5. Select “NO, I will restart my computer later” and then click button.
3 ………………………………………………
I/O Base Address & Interrupt Setting
The base address is set from SW1 DIP switch on board:
A8 A7 A6 A5 A4 A3
ON
1 2 3 4 5 6
SW1 : BASE ADDRESS
BASE ADDR A8 A7 A6 A5 A4 A3
200-207 OFF OFF OFF OFF OFF OFF
208-20F OFF OFF OFF OFF OFF ON
210-217
218-21F
220-227
228-22F
230-237
238-23F
:
:
3F0-3F7
3F8-3FF
OFF OFF OFF OFF ON OFF
OFF OFF OFF OFF ON ON
OFF OFF OFF ON
OFF OFF OFF ON
OFF OFF OFF ON
OFF OFF OFF ON
:
:
ON
ON
:
:
ON
ON
:
:
ON
ON
:
:
ON
ON
OFF
OFF
ON
ON
:
:
ON
ON
OFF
ON
OFF
ON
:
:
OFF
ON
( ) : default base address is 0x220
- 2 -
JP19: Interrupt Level Selection.
Select
IRQ 15
IRQ 3 4 5 6 7 9 10 11 12 15 14
No select
IRQ 3 4 5 6 7 9 10 11 12 15 14
4 ………………………………………………
Installing Hardware on PC
Follow those steps:
1. Shut down and power off your computer
2. Remove all covers from the computer
3. Select an empty ISA slot
4. Carefully insert your I/O card into the ISA slot
5. Replace the PC covers
6. Power on the computer
After powering-on the computer, continue next process.
- 3 -
5 ………………………………………………
Pin Assignments
CN1 is a 37 pin D-type connector.
Pin Number Description
1 PCB‘s GND
2
3
EXT_CLK1 / DI0
COUT1
4
5
EXT_CLK2 / DI1
EXT_CLK3 / DI2
10
11
12
13
6
7
8
9
COUT3
EXT_CLK4 / DI3
EXT_CLK7 / DI8
COUT7
EXT_CLK8 / DI9
EXT_CLK9 / DI10
COUT9
EXT_CLK10 / DI11
14
15
16
17
18
19
COUT6
DO0
DO2
DO4
DO6
PCB‘s +5V output
Pin Number Description
20 PCB‘s GND
21
22
EXT_GATE1 / DI4
EXT_GATE2 / DI5
23
24
COUT2
EXT_GATE3 / DI6
29
30
31
32
25
26
27
28
EXT_GATE4 / DI7
COUT4
EXT_GATE7 / DI12
EXT_GATE8 / DI13
COUT8
EXT_GATE9 / DI14
EXT_GATE10 / DI15
COUT10
33
34
35
36
COUT12
DO1
DO3
DO5
37 DO7
XXXXXXX This pin not available
The detail pin assignments information. Please refer to :
CD:\NAPDOS\ISA/TMC10/Manual/TMC10.pdf http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/tmc10/manual/tmc10.pdf
- 4 -
6 ………………………………………………
Self-Test
1. Use DN-37(Optional) to connect the board CN1.
2. DI8 connect to DO0 (Pin8 connect to Pin15)
DI9 connect to DO1 (Pin10 connect to Pin34)
DI10 connect to DO2 (Pin11 connect to Pin16)
DI11 connect to DO3 (Pin13 connect to Pin35)
DI12 connect to DO4 (Pin27 connect to Pin17)
DI13 connect to DO5 (Pin28 connect to Pin36)
DI14 connect to DO6 (Pin30 connect to Pin18)
DI15 connect to DO7 (Pin31 connect to Pin37)
CA-3710
CN1
DN-37 Wiring
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
- 5 -
3. Run the TMC-10 sample program.
Get the file from(Default):
C:\DAQPro\TMC10 NT\Demo
4. Check number of the TMC-10, and test DIO function.
1. Click this
I/O Base value
(Depend on I/O
Base Address)
2. Click this button to do
DIO test.
5. Get DIO function test result.
3. Click the channel
0 、 2 、 4 、 6 in the DO.
4. DI show to channel
0 、 2 、 4 、 6 for high state.
(Red light)
Complete
5. Not wiring channels for high state. (Red light)
- 6 -
7 ………………………………………………
Additional Information
TMC-10 Series Card Product page: http://www.icpdas.com/products/DAQ/pc_based/tmc_10.htm
DN-37(Optional) page: http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
Documents:
CD:\NAPDOS\ISA\TMC10\manual http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/tmc10/manual/
Software:
CD:\NAPDOS\ISA\TMC10 http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/tmc10/
The ICP DAS Web Site http://www.icpdas.com
Contact Us
Technical support
Supplies and ordering information
Ways to enhance your device
FAQ
Application story
[email protected]
Copyright ©2008 by ICP DAS Co., Ltd. All right are reserved
- 7 -
