JETWAY HPC-080SCSC-FP2807A, HPC-080SCSC-FP2930A User Manual

Panel PC

User’s Manual

NO. G03-PCNP93CFP-F

Manual Revision: 1.0

Release Date ： April 18, 2018

TABLE OF CONTENT

Safety Precautions.............................................................................................................. ii

User’s Notice....................................................................................................................... iii

Package Contents ............................................................................................................... iii

Environmental Protection Announcement ....................................................................... iii

Chapter 1 Introduction ..................................................................................................... 1

1-1 General Descriptions ............................................................................................ 1

1-2 Specifications ....................................................................................................... 2

1-3 I/O Outlets ............................................................................................................. 3

1-4 Connector Pin Definition ...................................................................................... 5

Chapter 2 Hardware and Installation ............................................................................... 7

2-1 Dimensions and Outlines ..................................................................................... 7

2-2 To Open the Chassis ............................................................................................ 10

2-3 Jumper Settings.................................................................................................... 11

2-4 Hardware Installation............................................................................................ 14

2-4-1 To install MSATA Card ............................................................................. 14

2-4-2 To install Wireless LAN Card ................................................................... 15

2-4-3 To install Optional Fixed Parts ................................................................ 17

Chapter 3 Introducing BIOS ............................................................................................. 18

3-1 Entering Setup ..................................................................................................... 18

3-2 BIOS Menu Screen............................................................................................... 19

3-3 Function Keys ...................................................................................................... 19

3-4 Getting Help ......................................................................................................... 19

3-5 Menu Bars ............................................................................................................ 20

3-6 Main Menu ............................................................................................................ 20

3-7 Advanced Menu ................................................................................................... 21

3-8 Chipset Menu ....................................................................................................... 27

3-9 Security Menu ...................................................................................................... 29

3-10 Boot Menu ............................................................................................................ 29

3-11 Save & Exit Menu ................................................................................................. 30

Chapter 4 Touch Panel ..................................................................................................... 31

APPENDIX ........................................................................................................................... 33

i

Safety Precautions

 Operate the product according to the correct installation steps and with great care to make sure safety and comfort using experience. Please refer to the following safety instruction guide to avoid danger of electric shock or fire. Abide by the previous safety instruction guide to use and maintain the product and the hard disk to make sure of safe operating environment.

 Please follow the instruction manual for operation guide.

 The appropriate operating temperature ranges from 0 °C–50 °C.

 The operation humidity for this product is 5% to 80% RH.

 To avoid high temperature, please DO NOT overload the maximum power of the external power supply while the system is consuming high voltage. Be aware of the maximum temperature allowance of the power supply.

 See to it that the product is not working near the water.

 Always unplug power cable and other hardware cables from the system before cleaning.

 Apply only dry cloth for cleansing the product.

 Make sure that there is no heat source nearby when the product is working.

 Make sure that the thermal louver of the product is not blocked.

 Make sure to remove the power plug from the product when there is a thunder storm.

 Please remove the power plug from the product when you are not going to use the product for a long time.

 Make sure to set up or use the product on a stable surface.

 Make sure not to drop the product or strike it by any means.

 Make sure not to move the product when the power is on.

 Make sure not to step on the power cables and other cables or rest anything in them..

 Be sure to ground yourself to prevent static charge when installing any internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge.

 Disconnect the power cord from the Panel PC unit prior to any installation. Be sure both the system and all external devices are turned off. Sudden surge of power could ruin sensitive components. Make sure the Panel PC unit is properly grounded. unit

 Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:

 Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on human body.

 When handling boards and components, wear a grounding wrist strap available from most electronic component stores.

 Please contact qualified technician for maintenance or repair.

 Use only accessories and parts that are made by the qualified manufacturer. ii

User’s Notice

Copyright of this manual belongs to the manufacturer. No part of this manual, including the products and software described in it may be reproduced, transmitted or translated into any language in any form or by any means without written permission of the manufacturer.

This manual contains all information required for the utilization of this product to meet the user’s requirements. But it will change, correct at any time without notice. Manufacturer provides this manual

“as is” without warranty of any kind, and will not be liable for any indirect, special, incidental or consequential damages (including damages for loss of profit, loss of business, loss of use of data, interruption of business and the like).

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and they are used only for identification or explanation and to the owner’s benefit, without intent to infringe.

Package Contents

X1 X1 X1 X1

Environmental Protection Announcement

X2 Optional

Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle. iii

Chapter 1

Introduction

1-1 General Descriptions

Thank you for purchasing the system, a new product developed, designed and manufactured under leading technical power and consistent dedication to fine workmanship.

 10-points Multi Capacitive Touch

 Cable-less,streamlined enclosure for highly efficient heat dissipation

 Enclosed in robust aluminum casing

 Edge-to-edge narrow bezel design and fan-less cooling system

 Designed for easy wall mount, panel mount, and VESA mount installation

 A true flat, easy-to-clean front surface with edge-to-edge design

 IO ports designed for easy connection

 IP65-rated front bezel against water and dust

 Onboard Intel® Bay Trail series SoC processor, with low power consumption never denies high performance

 Onboard 2GB DDR3L 1333Mhz SO-DIMM

 1* half-size Mini-PCIE slot & 1* full-size MSATA slot

 Support USB 3.0 data transport demand

 Support 4G SIM card socket

 Support 802.11 b/g/n WiFi communication

 Support HDMI video output

 Support RS232/422/485 serial port

The system has the following features besides other basic functions:

 WiFi: the Mini PCI-E onboard socket in the board is integrated a with a WiFi card(802.11 b/g/n) that can act as a mini wireless modem when external antennas are connected. Different computers in the house can build wireless connections through the Mini TOP system and take necessary data from it, thus reducing the complexity in network establishment.

 Giga LAN: The system is integrated with Gigabit LAN network controller with

ACPI management realizing efficient power management for the operating system.

 USB3.0: Experience Fastest data transfers at 5Gb/s with USB3.0 the new latest connectivity standard. Built connect easily with next-generation components and peripherals, USB3.0 transfers data 10x faster and backward compatible with previous USB2.0 components.

 CPU Usage: The CPU Usage diagram shows a beautiful data curve that indicates a pretty low CPU usage percentage for video playback of different formats. GPU performances are excellent as well.

 dB Value: The design of the system takes into consideration the needed quiet

1

operating environment in the living room and the average dB value is below 26 under normal operation to ensure the tranquility when you are absorbed in film watching.

1-2 Specifications

Main CPU Board



CPU



Intel

®

Bay Trail series SoC processor



System Memory



Onboard 2GB DDR3L 1333MHz SO-DIMM



BIOS



AMI 64Mb Flash ROM

I/O System



Standard I/O

For HPC070SC-FP2807A Series:



1 * Euro terminal block by 12V DC input





1 * USB3.0 & 1 * USB2.0 port

1 * RJ-45 LAN port for Gigabit Ethernet







1 * HDMI port

1 * RS232/422/485 serial port

1 * Power button

For HPC-080SC-FP2807A/ HPC-080SC-FP2930A & HPC-080SC-2807A Series:





1 * Euro terminal block by 12V DC input

1 * USB3.0 & 3 * USB2.0 port









1 * RJ-45 LAN port for Gigabit Ethernet

1 * HDMI port

1 * RS232/422/485 serial port & 1 * RS232 serial port

1 * Power button

2

1-3 I/O Outlets

For HPC070SC-FP2807A Series:

Bottom View

Rear IO

DC-in Jack

USB2.0

USB3.0

RJ-45

Q’ty

1

1

1

1

HDMI

RS232/422/485

RS232

Power Button

1

1

N/A

1

For HPC-080SC-FP2807A/ HPC-080SC-FP2930A Series:

Bottom View

Rear IO

DC-in Jack

USB2.0

USB3.0

RJ-45

HDMI

RS232/422/485

RS232

Power Button

Q’ty

1

3

1

1

1

1

1

1

3

For HPC-080SC-2807A Series:

RS232

1*USB 3.0 HDMI 1*RJ-45 DC-Jack

2*USB 2.0

Power

Button

RS232/422/485

1*USB 2.0

Bottom View

Rear IO

DC-in Jack

USB2.0

USB3.0

RJ-45

HDMI

RS232/422/485

RS232

Power Button

Q’ty

1

3

1

1

1

1

1

1

Notice:

1. The diagrams in this manual only serve for illustration, if there is any differences that we do not cover, please refer to the actual product you purchase.2.Model

HPC-080SCSC-FP2807A & HPC-080SCSC-FP2930A series share the same IO specifications, as the above diagram shows; 3.The main differences of

HPC-080SCSC-FP2807A & HPC-080SCSC-FP2930A series are mainly in size and different embedded CPU type.

4

1-4 Connector Pin Definition

(1) Connector Function

Icon Name Function

Power Button

Press to turn on/off the system.

USB 2.0 Port

To connect USB keyboard, mouse or other devices compatible with USB specification.

USB 3.0 Port

HDMI Port

COM Port

To connect USB keyboard, mouse or other devices compatible with USB specification. USB 3.0 ports supports up to 5Gbps data transfer rate.

To connect display device that support HDMI specification.

Mainly for user to connect external MODEM or other devices that supports Serial Communications Interface.

RJ-45 LAN Port

This connector is standard RJ-45 LAN jack for Network connection.

DC-in Power

Connector

For user to connect compatible terminal power block to provide power supply for the system.

(2) I/O Connectors Pin Definition

COM Port Connector

The pin assignment for RS-232/ 422/ 485 is listed as follows:

Pin NO. RS232

6

7

8

9

1

2

3

4

5

DCD

RXD

TXD

DTR

GND

DSR

RTS

CTS

RI

*RS422

(optional)

TX-

TX+

RX+

RX-

GND

NC

NC

NC

NC

*RS485

(optional)

DATA-

DATA+

NC

NC

GND

NC

NC

NC

NC

For RS232/422/485 COM port in normal settings can functions as RS232 port. With compatible COM cable they can function as RS422 or RS 485 port as well. User also needs to go to BIOS to set ‘Transmission Mode Select’ for COM1/COM2 (refer to

Page 21) at first, before using specialized cable to connect different pins of this port.

5

*Note: in the case that the COM port marked as RS232 port, it can not support

RS422/485 function.

RJ-45 Ethernet Connector

Ethernet connection can be established by plugging one end of the Ethernet cable into this RJ-45 connector and the other end (phone jack) to a 1000/100/10-Base-T hub.

The pin assignment for RJ-45 Ethernet LAN connectors are listed as follows:

Pin Definition Pin Definition

L1

L2

L3

L4

A

B

MDI0+

MDI0-

MDI1+

MDI1-

L5

L6

L7

L8

MDI2+

MDI2-

MDI3+

MDI3-

Active LED (Yellow)

100 LAN LED (Green) / 1000 LAN LED

(Orange)

6

Chapter 2

Hardware and Installation

2-1 Dimension and Outlines

Product Dimension for HPC070SC-FP2807A Series:

* Measure Unit: mm.

7

Product Dimension for HPC-080SC-FP2807A/ HPC-080SC-FP2930A Series:

* Measure Unit: mm.

8

Product Dimension for HPC-080SC-2807A Series:

* Measure Unit: mm.

9

2-2 To Open the Chassis

HPC070SC-FP2807A

HPC-080SC-FP2807A/HPC-080SC-FP2930A

HPC-080SC-2807A

Use a screwdriver to unscrew the screws marked above that lock the back cover (see red circles).

Remove them to open the chassis.

10

Notice: When lifting the cover up to open the chassis for further installation, see to it that the connecting cables are not unplugged. It is very important for the cables connected to their original places for normal functioning.

2-3 Jumper Settings

Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2 jumper pins to close the pins. And remove jumper clip from 2 jumper pins to open the pins. Diagram 2-1 illustrates how to set up a jumper.

JP1 (3-pin): INVERTER VLED 5V/12V Select

JP1 → INVERTER

1 3

1-2 Closed: Inverter VLED= 5V;

1 3

2-3 Closed: Inverter VLED= 12V.

JPCOM1 (4-pin): COM1 Header Pin9 Function Select

JCOMP1 → COM1 Header

6

4

2

5

3

1

2-4 Closed:

RI=RS232;

6

4

2

5

3

1

6

4

2

5

3

1

3-4 Closed:

RI= 5V;

4-6 Closed:

RI= 12V.

11

JP3 (4-pin): LVDS VLCD 3.3V/5V/12V Select

JP3 → LVDS VLCD

5 3 1

5 3 1

5 3 1

6 4 2

2-4 Closed:

VLCD = 3.3V

Pin 1-3 of J1 (10-pin): Clear CMOS Setting

6 4 2 6 4 2

3-4 Closed:

VLCD = 5V;

4-6 Closed:

VLCD = 12V;

Pin 1-3 of J1 → Clear CMOS Setting

10 9

2

Pin 1

10 9

1-3 Open: Normal;

1-3 Closed: Clear CMOS.

2

Pin 1

Pin 5-7 of J1 (10-pin): Clear Management Engine Setting

Pin 5-7 of J1 → Clear ME Select

10 9

5-7 Open: Normal;

2

Pin 1

10 9

5-7 Closed: Clear ME.

2

Pin 1

12

Pin 2-4 of J1 (10-pin): AT/ATX Mode Function Select

Pin 2-4 of J1 → AT Mode Select

10 9

2-4 Open:

ATX Mode Selected;

2

Pin 1

10 9

2-4 Closed:

AT Mode Selected.

2

Pin 1

*ATX Mode Selected: Press power button to power on after power input ready;

AT Mode Selected: Directly power on as power input ready.

Pin 6-8 of J1 (10-pin): Security Management Engine Function Select

Pin 6-8 of J1 → Didable ME Select

10 9

6-8 Open:

Normal;

6-8 Closed:

Disable ME Selected.

2

Pin 1

10 9

2

Pin 1

* Note: Pin-9 & Pin-10 of J1 block is only optional for the latest upgraded PCB version. The previous J1 block only come with 8 pins.

13

2-4 Hardware Installation

Remove the screws that lock the back cover to the system from the back side before hardware installation procedures (refer to 2-2).

2-4-1 To Install MSATA Card

1. Place the Panel PC with this side up upon a flat operation platform. See to it to put a protective cushion under the panel to prevent possible damage.

2. Remove the screws that lock the chassis on the back side of the system (refer to

2-2).

3. Locate the full-size MSATA slot on the board.

4. Remove the marked screw and use it to lock MSATA card to the slot in later installation.

14

5. Insert the gold-figure side of the compatible MSATA card into the slot at a

30 degree angle and press down.

6. Lock the card to the board by tightening up the screw to the marked spot.

2-4-2 To Install Wireless LAN Card

Please refer to the following instructions for the installation of the wireless LAN card.

1. Locate the Mini-PCIE card slot on the board.

2. Remove the marked screw and use it to lock WIFI card to the slot in later installation.

3. Insert the gold-figure side of the compatible WI-FI card into the slot and press down.

4. Lock the card to the board by tightening up the screw to the marked spot.

15

5. The metal hats on the end of the antenna string are sealed by acetate tape to avoid possible damage to the system.

6. Tear off the tape to find metal hats of

WiFi antenna string.

7. Press the metal hats on the end of the antenna string to the antenna slots on the card as showed.

16

2-4-3 To Install Optional Fixed Parts

1. The fixed parts are optional for specific models that support this kind of fixing mode.

2. The models that support this fixing mode have two slots reserved on both sides of the system.

3. Insert corresponding edges of the fixed part into the slots until them matched. The screw is for user to lock the system upon the platform with corresponding punched holes. Fix the other part to the other side of the system in the same way.

*Note:Fixed parts are only optional for specific models. Please refers to the actual prodcut for speficication.

17

Chapter 3

Introducing BIOS

Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard.

Users are welcome to download the latest BIOS version form our official website.

The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.

Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best.

3-1 Entering Setup

Power on the computer and by pressing <Del> immediately allows you to enter Setup.

If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the “RESET” button on the system case. You may also restart by simultaneously pressing <Ctrl>,

<Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to

Press <Del> to enter Setup

18

3-2 BIOS Menu Screen

The following diagram show a general BIOS menu screen:

Menu Bar

General Help Items

Menu Items

Current Setting Value

Function Keys

BIOS Menu Screen

3-3 Function Keys

In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here:

 Press  (left, right) to select screen;

 Press  (up, down) to choose, in the main menu, the option you want to confirm or to modify.

 Press <Enter> to select.

 Press <+>/<–> keys when you want to modify the BIOS parameters for the active option.

 [F1]: General help.

 [F2]: Previous value.

 [F3]: Optimized defaults.

 [F4]: Save & Exit.

 Press <Esc> to quit the BIOS Setup.

 [F7]: User can press this key to enter Boot Menu when system start up.

3-4 Getting Help

Main Menu

The on-line description of the highlighted setup function is displayed at the top right corner the screen.

19

Status Page Setup Menu/Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press

<Esc>.

3-5 Menu Bars

There are six menu bars on top of BIOS screen:

Main To change system basic configuration

Advanced

Chipset

Security

Boot

To change system advanced configuration

To change chipset configuration

Password settings

To change boot settings

Save & Exit Save setting, loading and exit options.

User can press the right or left arrow key on the keyboard to switch from menu bar.

The selected one is highlighted.

3-6 Main Menu

Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item.

System Date

Set the date. Please use [Tab] to switch between date elements.

System Time

Set the time. Please use [Tab] to switch between time elements.

20

3-7 Advanced Menu

OS Selection

The optional settings: [Windows 8.X]; [Linux/Android]; [Windows 7].

* Note: User need to go to this item to select the OS mode before installing corresponding OS driver, otherwise problems will occur when installing the driver.

 ACPI Settings

Press [Enter] to make settings for the following sub-item:

ACPI Settings

ACPI Sleep State

Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed.

The optional settings are: [Suspend Disabled]; [S3 (Suspend to RAM)].

 Super I/O Configuration

Press [Enter] to make settings for the following sub-items:

Super IO Configuration

 Serial Port 1 Configuration

Press [Enter] to make settings for the following items:

Serial Port

Use this item to enable or disable serial port (COM).

Change Settings

Use this item to select an optimal setting for super IO device.

Transmission Mode Select

The optional settings are: [RS422]; [RS232]; [RS485].

Mode Speed Select

The optional settings are: [RS232/RS422/RS485=250kbps]; [RS232=1Mbps,

RS422/RS485=10Mbps].

Serial Port FIF0 Mode

The optional settings are: [16-Byte FIF0]; [32-Byte FIF0]; [64-Byte FIF0]; [128-Byte

21

FIF0].

 Serial Port 2 Configuration

Press [Enter] to make settings for the following items:

Serial Port

Use this item to enable or disable serial port (COM).

Change Settings

Use this item to select an optimal setting for super IO device.

Serial Port FIF0 Mode

The optional settings are: [16-Byte FIF0]; [32-Byte FIF0]; [64-Byte FIF0]; [128-Byte

FIF0].

ERP Function

The optional settings:[Disabled]; [Enabled].

This item should be set as [Disabled] if you wish to have all active wake-up functions.

WatchDog Timer

Use this item to enable or disable WatchDog Timer Control. When set as

[Enabled], the following sub-items shall appear:

WatchDog Timer Value

User can set a value in the range of [10] to [255].

WatchDog Timer Unit

The optional settings are: [Sec.]; [Min.].

WatchDog Wake-up Timer in ERP

This item support WDT wake-up while ERP function is set as [Enabled].

The optional settings are: [Enabled]; [Disabled].

When set as [Enabled], the following sub-items shall appear:

WatchDog Timer Value in ERP

User can select a value in the range of [10] to [4095] seconds when ‘WatchDog

Timer Unit in ERP’ set as [Sec]; or in the range of [1] to [4095] minutes when

‘WatchDog Timer Unit in ERP’ set as [Min].

WatchDog Timer Unit

The optional settings are: [Sec.]; [Min.].

ATX Power Emulate AT Power

This item support Emulate AT power function, MB power On/Off control by power supply. Use needs to select ‘AT or ATX Mode’ on MB jumper at first (ATX Mode &

AT Mode Select).

 Serial Port Console Redirection


COM1/COM2

Console Redirection

Use this item to enable or disable COM1 Console Redirection.

The optional settings are: [Disabled]; [Enabled].

When set as [Enabled], user can make further settings in the ‘Console

Redirection Settings’ screen:

 Console Redirection Settings

22

The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Press [Enter] to make settings for the following sub-items ：

Terminal Type

The optional settings are: [VT100]; [VT100+]; [VT-UTF8]; [ANSI].

Bits per second

The optional settings are: [9600]; [19200]; [38400]; [57600]; [115200].

Data Bits

The optional settings are: [7]; [8].

Parity

The optional settings are: [None]; [Even]; [Odd];[Mark]; [Space].

Stop Bits

The optional settings are: [1]; [2].

Flow Control

The optional settings are: [None]; [Hardware RTS/CTS].

VT-UTF8 Combo Key Support


Recorder Mode


Resolution 100x31

The optional settings are:[Disabled]; [Enabled].

Legacy OS Redirection Resolution

The optional settings are: [80x24]; [80x25].

Putty Keypad

The optional settings are: [VT100]; [LINUX]; [XTERMR6]; [SCO]; [ESCN];

[VT400].

Redirection After BIOS POST

The optional settings are: [Always Enable]; [BootLoader].

Legacy Console Redirection

 Legacy Console Redirection Settings

Press [Enter] to make settings in ‘Legacy Serial Redirection Port’.

Legacy Serial Redirection Port

Use this item to select a COM port to display redirection of Legacy OS and Legacy

OPROM messages.

The optional settings: [COM1]; [COM2].

Serial Port for Out-of-Band Management/

Windows Emergency Management Services (EMS)

Console Redirection

The optional settings: [Disabled]; [Enabled].

When set as [Enabled], user can make further settings in ‘Console Redirection

Settings’ screen:

 Console Redirection Settings

The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Press [Enter] to make settings for the following sub-items.

23

Out-of-Band Mgmt Port

The optional settings are: [COM1]; [COM1(Pci Bus0, Dev0, Func0) (Disabled)].

Terminal Type

The optional settings are: [VT100]; [VT100+]; [VT-UTF8]; [ANSI].

Bits per second

The optional settings are: [9600]; [19200]; [57600]; [115200].

Flow Control

The optional settings are: [None]; [Hardware RTS/CTS]; [Software Xon/Xoff].

Data Bits

The default setting is: [8].

*This item may or may not show up, depending on different configuration.

Parity

The default setting is: [None].


Stop Bits

The default setting is: [1].


 PC Health Status

Press [Enter] to view current hardware health status and set value in ‘Shutdown

Temperature’.

Shutdown Temperature

Use this item to select system shutdown temperature.

The optional settings are: [Disabled]; [70

[85 o

C/180 o

F]; [90 o

C/188 o

F]. o

C/156 o

F]; [75 o

C/164 o

F]; [80 o

C/172 o

F];

 CPU Configuration

Press [Enter] to view current CPU configuration and make settings for the following sub-items:

Limit CPUID Maximum


This item should be set as [Disabled] for Windows XP.

Execute Disable Bit


Hardware Prefetcher


Use this item to turn on/off the Mid Level Cache (L2) streamer prefetcher.

Adjacent Cache Line Prefetch


Use this item to turn on/off prefetching of adjacent cache lines.

Intel Virtualization Technology

The optional settings: [Enabled]; [Disabled].

When set as [Enabled], a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

EIST


Use this item to enable or disable Intel SpeedStep.

CPU C State Report


24

When set as [Enabled], the following item shall appear:

Enhanced C state

Use this item to enable or disable CPU Enhanced C state.


Max CPU C-State

This item controls Max C-state that the processor will support.

The optional settings: [C7]; [C6]; [C1].

 SATA Configuration


SATA Configuration

SATA Controller


SATA Speed Support

The item is for user to set the maximum speed the SATA controller can support.

The optional settings are: [Gen1]; [Gen2].

SATA Mode

The optional settings are: [IDE Mode]; [AHCI Mode].

SATA Port

The optional settings are: [Enabled]; [Disabled]. m-SATA


 Network Stack Configuration

Press [Enter] to go to ‘Network Stack’ screen to make further settings.

Network Stack


When set as [Enabled], the following sub-items shall appear:

Ipv4 PXE Support


Use this item to enable Ipv4 PXE Boot Support. When set as [Disabled], Ipv4 boot optional will not be created.

Ipv6 PXE Support


Use this item to enable Ipv6 PXE Boot Support. When set as [Disabled], Ipv4 boot optional will not be created.

PXE boot wait time

Use this item to set wait time to press [ESC] key to abort the PXE boot.

 CSM Configuration


Compatibly Support Module Configuration

Boot Option Filter

This item controls Legacy/UEFI ROMs priority.

The optional settings are: [UEFI and Legacy]; [Legacy Only]; [UEFI Only].

Network

This item controls the execution of UEFI and legacy PXE OpROM.

The optional settings are: [Do not launch]; [UEFI only]; [Legacy only].

Storage

This item controls the execution of UEFI and Legacy Storage OpROM.

The optional settings are: [Do not launch]; [UEFI only]; [Legacy only].

25

Other PCI devices

This item determines OpROM execution policy for devices other than Network, storage or video.

The optional settings are: [UEFI only]; [Legacy only].

 Wake-up Function Settings


Wake-up System with Fixed Time

Use this item to enable or disable system wake-up by RTC alarm.


When set as [Enabled], system will wake on the hour/min/sec specified.

Wake-up System with Dynamic Time

Use this item to enable or disable system wake-up by RTC alarm.


When set as [Enabled], system will wake on the current time + increased minute(s).

*This function is supported when EUP Function is set as [Disabled].

USB1 Wake-up from S3-S4/USB2 Wake-up from S3-S4/USB3 Wake-up from

S3-S4/USB4 Wake-up from S3-S4


USB Wake-up is affected by ERP function in S4. Please disable ERP before activating this function in S4.

 USB Configuration


USB Configuration

Legacy USB Support

The optional settings are: [Enabled]; [Disabled]; [Auto].

[Enabled]: To enable legacy USB support.

[Disabled]: To keep USB devices available only for EFI specification,

[Auto]: To disable legacy support if no USB devices are connected.

XHCI Hand-off

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.


EHCI Hand-off

This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver.


USB Mass Storage Driver Support


USB hardware delay and time-outs:

USB Transfer Time-out

Use this item to set the time-out value for control, bulk, and interrupt transfers.

The optional settings are: [1 sec]; [5 sec]; [10 sec]; [20 sec].

Device Reset Time-out

Use this item to set USB mass storage device start unit command time-out.

The optional settings are: [10 sec]; [20 sec]; [30 sec]; [40 sec].

Device Power-up Delay

Use this item to set maximum time the device will take before it properly reports

26

itself to the host controller. ‘Auto’ uses default value: for a root port it is 100 ms, for a hub port the delay is taken from hub descriptor.

The optional settings: [Auto]; [Manual].

Select [Manual] you can set value for the following sub-item: ‘Device Power-up

Delay in Seconds’.

Device Power-up Delay in Seconds

The delay range is from [1] to [40] seconds, in one second increments.

 Reltek PCIe GBE Family Controller (MAC:XX:XX:XX:XX:XX:XX)

Use this item to get driver information and configure Realtek ethernet controller parameter.

3-8 Chipset Menu

 North Bridge

Press [Enter] to view current using memory information and make settings for the following sub-items:

PAVC

Use this item to enable or disable Protected Audio Video Control.

The optional settings are: [Disabled]; [LITE Mode]; [SERPENT Mode].

DVMT Pre-Allocated

Use this item to select DVMT 5.0 pre-allocated (fixed) graphics memory size used by the internal graphics device.

The optional settings are: [64M]; [96M]; [128M]; [160M]; [192M]; [224M]; [256M];

[288M]; [320M]; [352M]; [384M]; [416M]; [448M]; [480M]; [512M].

DVMT Total Gfx Mem

Use this item to select DVMT 5.0 total graphics memory size used by the internal graphics device.

The optional settings are: [128 MB]; [256 MB]; [MAX].

Aperture Size

The optional settings are: [128 MB]; [256 MB]; [512MB].

27

GTT Size

The optional settings are: [1MB]; [2 MB].

Primary IGFX Boot Display

Use this item to select the video device which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection.

The optional settings are: [VBIOS Default]; [HDMI]; [LVDS].

* Note: [LVDS] option only shows up when ‘Active LVDS’ item is set as [Enabled].

Active LVDS


[Disable]: VBIOS does not enable LVDS.

[Enable]: VBIOS enable LVDS driver by integrated encoder.

* Note: When set as ‘Enabled’, user can make further settings in ‘LCD Panel

Type’

LCD Panel Type

Use this item to select LCD panel resolution.

The optional setting are: [640 x 480 18-bit]; [800x 600 18-bit]; [1024 x 600 18-bit];

[1024 x 768 24-bit]; [1280 x 720 18-bit]; [800 x 480 18-bit]; [1366 x 768 18-bit];



[1920 x 1080 24-bit].

 South Bridge

Press [Enter] to make further setting in the following sub-items:

Mini PCIE


Mini PCIE Speed

The optional settings are: [Auto]; [Gen2]; [Gen1].

Onboard PCIE LAN


Audio Controller

Use this item to control the detection of the Azalia HD Audio device.


[Disabled]: Azalia will be unconditionally disabled;

[Enabled]: Azalia will be unconditionally enabled;

Azalia HDMI Codec

Use this item to enable or disable internal HDMI codec for Azalia.


 USB Configuration


USB Configuration

USB 3.0 Support

This item is for user to select mode of operation of XHCI controller.

The optional settings are: [Enabled]; [Auto]; [Disabled].

USB 2.0 Support

This item is for user to control the USB EHCI (USB2.0) functions. One EHCI controller must always be enabled.


System state after Power Failure

28

Use this item to select AC power state when ACpower is re-applied after a power failure. The optional settings are: [Always On]; [Always Off]; [Former State].

*[Always On] and [Former State] options are affected by ERP function. Please disable ERP to support [Always On] and [Former State].

3-9 Security Menu

Security menu allow users to change administrator password and user password settings.

3-10 Boot Menu

Boot Configuration

29

Setup Prompt Timeout

Use this item to set number of seconds to wait for setup activation key.

Bootup Numlock State

Use this item to select keyboard numlock state.

The optional settings are: [On]; [Off].

Quiet Boot


Boot Option Priorities

Boot Option#1/2…

The optional settings are: [UEFI: Built-in EFI Shell]; [Disabled].

3-11 Save & Exit Menu

Save Changes and Reset

This item allows user to reset the system after saving the changes.

Discard Changes and Reset

This item allows user to reset the system without saving any changes.

Restore Defaults

Use this item to restore /load default values for all the setup options.

Save as User Defaults

Use this item to save the changes done so far as user defaults.

Restore User Defaults

Use this item to restore defaults to all the setup options.

Boot Oerride

UEFI: Built-in EFI Shell

Press this item and a dialogue box shall appear to ask if user wish to save configuration and reset.

Reset System with TXE disable Mode

Press [Enter] for TXE to run into the temporary disable mode. Ignore if TXE Ignition

FM.

30

Chapter 4

Touch Panel

HPC070SC-FP2807A is designed based on the technology of projected capacitive type multi-touch screen of which specifications are listed below:

Specification

Front Bazel

Display Type

Display

IP65, NEMA 4 rugged protection, Full planar metal border

7’’ with LED backlight

Brightness

Display Color

320 nits

16.7M

Resolution 1024 x 600 @ 60Hz

Viewing Angle (H/V) 150 o

/145

o

Pixel Pitch 0.15 x 0.15 mm

Aspect Ratio

Contrast Ratio

Response Time

16:9

500:1

30 ms

Touch Screen

Type

Active Range

Transparency

Surface Hardness

Glass haze value projected capacitive type

152.40 x 91.44mm ±0.2mm

≥85%

≥6H(JIS-5400)

≤3%

HPC080SC-FP2807A/ HPC080SC-FP2930A is designed based on the technology of of projected capacitive type multi-touch screen of which specifications are listed below:

Specification

Front Bazel

Pixel Pitch

Aspect Ratio

Contrast Ratio

Response Time

Display

IP65, NEMA 4 rugged protection, Full planar metal

Display Type

Brightness

Display Color border


400 nits

16.7m



/160

o

0.158 x 0.158 mm

4:3

700:1

30 ms

Type

Active Range

Touch Screen

Projective capacitive type

Transparency

Surface Hardness

163.05 x 122.54mm ±0.2mm

≥85%

≥6H(JIS-5400)

31

HPC-080SC-2807A is designed based on the technology projective capacitive type multi-touch screen of which specifications are listed below:

Specification

Front Bazel

Display Type

Brightness

Display Color

Display

IP65, NEMA 4 rugged protection, metal front bazel




/160

o

Pixel Pitch

Aspect Ratio

Contrast Ratio

0.158 x 0.158 mm

4:3

700:1

Response Time

400 nits

16.7M

Type

Active Range

Transparency

30 ms

Touch Screen

Projective capacitive type

163.05 x 122.54mm ±0.2mm

Surface Hardness

Glass haze value

≥85%

≥6H(ASTM D3363, pressure 1N/45

o

)

≤3%

32

Appendix

General Notices

European Union CE Marking and Compliance Notices

Products intended for sale within the European Union are marked with the Conformity European (CE)

Making, which indicates compliance with the applicable Directive and European standards and amendments identified.

Shielded Cables Notice

All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Peripheral Devices Notice

Only peripherals (input/out devices, terminals, printers, etc) certified to comply with Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception.

Wireless Related Information

Wireless Interoperability

Wireless LAN PCI Express Mini Card is designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CKK), and/or Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to:

The IEEE802.11a/b/g/n Standard on Wireless LANs was defined and approved by the Institute of

Electrical and Electronics Engineers.

The Wireless Fidelity (WiFi) certification as defined by the Wi-Fi Alliance.

Usage Environment and Your Health

Wireless LAN PCI Express Mini Card emits radio frequency electromagnetic energy like other radio devices. However, the level of energy emitted is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.

Due to the fact that Wireless LAN PCI Express Mini Card operates within the guidelines found in radio frequency safety standards and recommendations, we believe the integrated wireless cards are safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

In some situation or environment, the use of Wireless LAN PCI Express

Mini Card may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

Using the integrated wireless cards on board of airplanes, or in hospitals

In any other environment that the risk of interference to other devices and service are perceived or identified to be harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization

(e.g., airport or hospital), you are encouraged to ask for authorization to use Wireless LAN PCI Express

Mini Card prior to turning on the computer.

33

Electronic Emissions Notices

European Union Compliance Statement Class B Compliance

European Union – Compliance to the Electromagnetic Compatibility Directive

This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. We cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.

This product has been tested and found to comply with the limits Class B Information Technology

Equipment according to European Standard EN55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices.

Properly shielded and grounded cables and connectors must be used in order to reduce the potential for causing interference to radio and TV communications and to other electrical or electronic equipment.

FCC Rules and Regulations-Part 15

This devices uses, generates and radiates radio frequency energy. The radio frequency energy produced by this device is well below the maximum exposure allowed by the Federal Communications

Commission (FCC)

 This device complies with the limits for the Class B digital device pursuant to Part 15 subject to the following two conditions:

 This device may not cause harmful interference.

 This device must accept any interference received, including interference that may cause undesired operation.

The FCC limits are designed to provide reasonable protection against harmful interference when the equipment is installed and used in accordance with the instruction manual and operated in a commercial environment. However, there is no guarantee that interference will not occur in a particular commercial installation, or if operated in a residential area.

If harmful interference with radio or television reception occurs when the device is turned on, the user must correct the situation at the user’s own expense. The user is encouraged to try one or more of the following corrective measures:

 Re-orient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that on which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

CAUTION: The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by

Intel could void the user’s authority to operate this device.

34

JETWAY HPC-080SCSC-FP2807A, HPC-080SCSC-FP2930A User Manual

Panel PC

User’s Manual

TABLE OF CONTENT

Safety Precautions

User’s Notice

Package Contents

Environmental Protection Announcement

Chapter 1

Introduction

1-1 General Descriptions

1-2 Specifications

1-3 I/O Outlets

1-4 Connector Pin Definition

Chapter 2

Hardware and Installation

2-1 Dimension and Outlines

2-2 To Open the Chassis

2-3 Jumper Settings

2-4 Hardware Installation

2-4-1 To Install MSATA Card

2-4-2 To Install Wireless LAN Card

2-4-3 To Install Optional Fixed Parts

Chapter 3

Introducing BIOS

3-1 Entering Setup

3-2 BIOS Menu Screen

3-3 Function Keys

3-4 Getting Help

Main Menu

Status Page Setup Menu/Option Page Setup Menu

3-5 Menu Bars

There are six menu bars on top of BIOS screen:

3-6 Main Menu

3-7 Advanced Menu

3-8 Chipset Menu

3-9 Security Menu

3-10 Boot Menu

3-11 Save & Exit Menu

Chapter 4

Touch Panel

Specification

Specification

Specification

Appendix

General Notices

Wireless Related Information

Electronic Emissions Notices

FCC Rules and Regulations-Part 15

Related manuals

JETWAY

HBFHP792C Series

JETWAY

HPC-101

Intel

H110 Express

JETWAY

HPC070SC-FP2807A

JETWAY

HPC080SC-FP2807A

JETWAY

HPC-104BR-2930-4G

JETWAY

JNP793D2-3160

JETWAY

HPC-101

JETWAY

HPC080SC-FP3350

Mintronix Computer Solutions

MP5000C

Cumberland

Converting EDGE 1 to EDGE 2