Europe EB-430 Projector User Manual

User’s Guide

Notations Used in This Guide

•

Safety indications

The documentation and the projector use graphical symbols to show how to use the projector safely.

The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.

Warning

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

Caution

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

•

General information indications

Attention a s

g

[Name]

Menu Name

Indicates procedures which may result in damage or injury if sufficient care is not taken.

Indicates additional information and points which may be useful to know regarding a topic.

Indicates a page where detailed information regarding a topic can be found.

Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendices".

s

"Glossary" p.129

Indicates the name of the buttons on the remote control or the control panel.

Example: [Esc] button

Indicates Configuration menu items.

Example:

Select Brightness from Image .

Image - Brightness

Contents

3

Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2

Introduction

Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Enabling projection from a short distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Easy writing on a whiteboard or blackboard using the pattern function . . . . . . . . 7

Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . . . . . . 7

Connecting to a network and projecting images from the computer's screen

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Enhanced security functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Optional Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Enlarge and project your files with the Document Camera . . . . . . . . . . . . . . . . . 7

Easy connection to a computer with Quick Wireless . . . . . . . . . . . . . . . . . . . . . 7

Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Preparing the Projector

Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting a microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Connecting External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installing the Optional Wireless LAN Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Basic Usage

Projecting images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

From Installation to Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Automatically Detect Input Signals and Change the Projected Image (Source Search)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Switching to the Target Image Using the Remote Control . . . . . . . . . . . . . . . . . . 30

Projecting with USB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Connecting for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Correcting Keystone Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

H/V-Keystone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Quick Corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Adjusting the Image Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Adjusting the Horizontal Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . . . . . 38

Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . . . . . . 40

Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Changing the aspect mode (EB-435W/EB-425W only) . . . . . . . . . . . . . . . . . . . 40

Changing the aspect mode (EB-430/EB-420 only) . . . . . . . . . . . . . . . . . . . . . . 41

Useful Functions

Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . . . 44

Contents

4

Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Pointer Function (Pointer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . . . 47

Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Saving User Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Managing Users (Password Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Kinds of Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Setting Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Restricting Operation (Control Panel Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Installing the wire lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Configuration Menu

Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Network Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Soft keyboard operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Basic menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Wireless LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Wired LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Mail menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Others menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Troubleshooting

Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Moving images are not displayed (only the moving image portion turns black)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

The message "Not supported" is displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . 84

The message "No Signal" is displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . . . 85

The image is truncated (large) or small, or the aspect is not suitable . . . . . . . . . 86

Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . . . 89

No sound can be heard from the microphone . . . . . . . . . . . . . . . . . . . . . . . . 89

The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

I want to change the language for messages and menus . . . . . . . . . . . . . . . . . 90

Mail is not received even if an error occurs with the projector . . . . . . . . . . . . . 90

About Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Contents

5

Maintenance

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Appendix

Slideshow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Projecting Without a Computer (Slideshow) . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Specifications for files that can be projected using Slideshow . . . . . . . . . . . . . 103

Slideshow examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Slideshow operating methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Projecting the selected image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Projecting image files in a folder in sequence (Slideshow) . . . . . . . . . . . . . . . 106

Image file display settings and Slideshow operation settings . . . . . . . . . . . . . 107

Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

About EasyMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . . . . . . 108

Projector setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Displaying the Web Remote screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . . . . 111

Reading Error Notification Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Cable layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

About PJLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

About Crestron RoomView

®

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . . . . . . 114

Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 118

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 119

Projection Distance (For EB-430/EB-420) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Projection Distance (For EB-435W/EB-425W) . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Component Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Composite video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Input signal from the HDMI port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Introduction

This chapter explains the projector's features and the part names.

Projector Features

7

Projection Functions

Enabling projection from a short distance

You can project large images from a short distance without having to move the projector away from the screen.

s

"Screen Size and Projection Distance" p.119

Easy writing on a whiteboard or blackboard using the pattern function

You can project ruled lines and grid patterns. This is useful when drawing diagrams on a whiteboard or blackboard.

s

Settings - Pattern

p.63

Enhanced security functions

•

Password Protect to restrict and manage users

By setting a password you can restrict who can use the projector.

s

"Managing Users (Password Protect)" p.52

•

Control Panel Lock restricts button operation on the control panel

You can use this to prevent people changing projector settings without permission at events, in schools, and so on.

s

"Restricting Operation (Control Panel Lock)" p.54

•

Equipped with various anti-theft devices

The projector is equipped with the following types of anti-theft security devices.

•

Security slot

•

Security cable installation point s

"Anti-Theft Lock" p.55

Connecting with a USB cable and projecting (USB Display)

By simply connecting a commercially available USB cable, you can project images from a computer's screen without a computer cable.

s

"Projecting with USB Display" p.30

Connecting to a network and projecting images from the computer's screen

You can connect the projector to a computer on a network and project the computer's screen using the supplied EasyMP Network Projection

(application software).

s EasyMP Network Projection Operation Guide

Optional Functions

Enlarge and project your files with the Document Camera

You can project paper documents and objects using the optional Document

Camera. Image focus is automatically adjusted using the auto focus function. You can also enlarge images using digital zoom.

s

"Optional Accessories" p.118

Easy connection to a computer with Quick Wireless

By simply connecting the optional Quick Wireless Connection USB Key to a computer, you can project the computer's screen. (Windows computers only) s


Part Names and Functions

Front/Top

A

Name

Remote receiver

Function

Receives signals from the remote control.

B Foot adjust lever Press the foot lever to extend and retract the front foot.

s

"Adjusting the Image Position" p.37

C Front adjustable foot When setup on a surface such as a desk, extend the foot to adjust the position of the image.

s


Name

D Air intake vent

(air filter)

E Focus ring

F Control panel

G Lamp cover

H Air exhaust vent

I Indicators

J Lens cover

Function

Takes in air to cool the projector internally.

s

"Cleaning the Air Filter" p.94

s

"Replacing the Air Filter" p.99

Adjusts the image focus.

s

"Correcting the Focus" p.38

Operates the projector.

s

"Control Panel" p.11

Open when replacing the projector's lamp.

s

"Replacing the Lamp" p.96

Exhaust vent for air used to cool the projector internally.

Caution

While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent.

Indicates the projector's status.

s

"Reading the Indicators" p.79

Attach the cover when not using the projector to prevent the lens from getting dirty or being damaged.

8


Rear

Name

A HDMI port

B Video port

C RS-232C port

D Monitor Out port

E Audio1 port

F Audio Out port

Function

Inputs video signals from HDMI compatible video equipment and computers. This projector is compatible with HDCP

g .

s

"Connecting Equipment" p.18

Inputs composite video signals from video sources.

When controlling the projector from a computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used.

s

"ESC/VP21 Commands" p.112

Outputs analog RGB signals input from the Computer1 port to an external monitor. You cannot output signals input from other ports or component video signals.

Inputs audio from equipment connected to the

Computer1 port.

Outputs audio from the currently projected image or the

Mic port to an external speaker.

H

I

Name

G Mic port

Power inlet

Security slot

J Wireless LAN unit installation section

K Speaker

L LAN port

M USB(TypeA) port

N

O

P

Q

USB(TypeB) port

Computer2 port

Audio2 port

Computer1 port

Function

Inputs audio from the microphone.

s

"Connecting a microphone" p.23

Connects the power cable to the projector.

s

"From Installation to Projection" p.28

The security slot is compatible with the Microsaver

Security System manufactured by Kensington.

s


Install the optional Wireless LAN unit here. Remove the stopper when installing.

s

"Installing the Optional Wireless LAN Unit" p.26

Outputs audio.

Connects a LAN cable to connect to a network.

•

Connects a USB memory device or a digital camera, and projects images as a Slideshow.

s

"Projecting Without a Computer (Slideshow)" p.103

•

Connects the optional Document Camera.

•

Connects the projector to a computer via a commercially available USB cable, and projects the images on the computer.

s


•

Connects the projector to a computer via the commercially available USB cable to use the Wireless

Mouse function.

s

"Using the Remote Control to Operate the

Mouse Pointer (Wireless Mouse)" p.47

Inputs image signals from a computer and component video signals from other video sources.

Inputs audio from equipment connected to the

Computer2 port.

Inputs image signals from a computer and component video signals from other video sources.

9


Name

R Audio-L/R port

S S-Video port

Function

Inputs audio from equipment connected to the S-Video port or the Video port.

For S-video signals from video sources.

Base

10

Name

A Ceiling mount fixing points (three points)

B Wall mount plate fixing points (five points)

Function

Attach the optional Ceiling Mount here when suspending the projector from a ceiling.

s

"Installing the Projector" p.17

s


Attach the optional wall mount plate here when suspending the projector from a wall.

s



C

Name

Rear feet

Function

When setup on a surface such as a desk, turn to extend and retract to adjust the horizontal tilt.

s

"Adjusting the Horizontal Tilt" p.37

D Security cable installation point

Pass a commercially available wire lock through here and lock it in place.

s

"Installing the wire lock" p.55

E Front adjustable foot When setup on a surface such as a desk, extend the foot to adjust the position of the image.

s


Control Panel

11

Name

A [ t ] button

B [Source Search] button

C

[ ] button

Function

Turns the projector power on or off.

s


Switches to the image from the input port where video signals are being input.

s

"Automatically Detect Input Signals and Change the

Projected Image (Source Search)" p.29

•

When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

•

If pressed while projecting analog RGB signals from

Computer1 port or Computer2 port, you can automatically optimize Tracking, Sync., and Position.


D [ w ][

Name v ] button

Function

•

Displays the Keystone screen allowing you to correct keystone distortion in vertical and horizontal directions.

s

"H/V-Keystone" p.34

•

If pressed when the Configuration menu or the Help screen is displayed, these buttons select menu items and setting values.

s

"Using the Configuration Menu" p.57

s

"Using the Help" p.78

E

F

[Help] button

[Esc] button

Displays and closes the help screen which shows you how to deal with problems if they occur.

s


•

Stops the current function.

• If pressed when the Configuration menu is displayed, it moves to the previous menu level.

s


G [Tele]/[Wide] buttons

•

Adjusts the size of the projection screen. Press the [Tele] button to reduce the size of the projection screen and press the [Wide] button to increase the size of the projection screen.

• Corrects keystone distortion in the horizontal direction when the Keystone screen is displayed.

s

"H/V-Keystone" p.34

• If pressed when the Configuration menu or the Help screen is displayed, these buttons select menu items and setting values.

s


s


H [Menu] button Displays and closes the Configuration menu.

s


Remote Control

12


13

Name

A [ t ] button

B [Computer] button

C

D

E

F

G

H

[Video] button

Numeric buttons

[Auto] button

[Aspect] button

[Num] button

[Menu] button

Function


s


Each time you press the button, the input changes between images from the Computer1 port and the Computer2 port.

Each time the button is pressed, the image cycles through the S-Video, Video, and HDMI ports.

• Enter the Password.

s

"Setting Password Protect" p.52

• Use this button to enter numbers in Network settings from the Configuration menu.

If pressed while projecting analog RGB signals from

Computer1 port or Computer2 port, you can automatically optimize Tracking, Sync., and Position.

Each time the button is pressed, the aspect mode changes.

s

"Changing the Aspect Ratio of the Projected Image" p.40

Hold down this button and press the numeric buttons to enter passwords and numbers.

s


Displays and closes the Configuration menu.

s


Name

I

[ ][ ][ ][ ] button

J [User] button

K [Page] buttons

[ [ ][ ] ]

L [A/V Mute] button

Function

•

When the Configuration menu or Help screen is displayed, pressing these buttons selects menu items and setting values.

s


•

When projecting a Slideshow, pressing these buttons displays the previous/next image, rotates the image, and so on.

s

"Slideshow operating methods" p.103

•

During Wireless Mouse function, the mouse pointer moves in the direction of the button that was pushed.

s



Select any frequently used item from the seven available

Configuration menu items, and assign it to this button. By pressing the [User] button, the assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments.

s

"Settings Menu" p.63

Power Consumption is assigned as the default setting.

Changes pages in files such as PowerPoint files when using the following projection methods.

• When using the Wireless Mouse function s



• When using USB Display s


• When connecting to a network

When projecting images using Slideshow, pressing these buttons displays the previous/next image file.

Turns the video and audio on or off.

s

"Hiding the Image and Sound Temporarily (A/V

Mute)" p.44


14

Name

M [E-Zoom] buttons

[ z ][ x ]

N Strap hole

O [Help] button

P [Freeze] button

Q [Volume] buttons

[ a ][ b ]

R [Pointer] button

S

[ ] button

T [Esc] button

Function

Enlarges or reduces the image without changing the projection size.

s

"Enlarging Part of the Image (E-Zoom)" p.46

Allows you to attach a commercially available strap to the remote control.

Displays and closes the help screen which shows you how to deal with problems if they occur.

s


Pauses or resumes image playback.

s

"Freezing the Image (Freeze)" p.44

[ a ] Decreases the volume.

[ b ] Increases the volume.

s

"Adjusting the Volume" p.38

Displays the on-screen pointer.

s

"Pointer Function (Pointer)" p.45

• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

s


• Acts as a mouse's left button when using the Wireless

Mouse function.

s



• Stops the current function.

•

If pressed when the Configuration menu is displayed, it moves to the previous level.

s


•

Acts as a mouse's right button when using the Wireless

Mouse function.

s



U

V

W

X

Name

[Color Mode] button

[LAN] button

[USB] button

[Source Search] button

Y Remote control lightemitting area

Function

Each time the button is pressed, the color mode changes.

s

"Selecting the Projection Quality (Selecting Color

Mode)" p.38

Changes to the images projected with EasyMP Network

Projection. When projecting using the optional Quick

Wireless Connection USB Key, this button switches to that image.

Each time the button is pressed, it cycles through the following images:

• USB Display

• Images from the device connected to the USB(TypeA) port


s



Outputs remote control signals.


Replacing the remote control batteries

If the remote control becomes unresponsive or inoperable after it has been used for some time, the batteries may have reached the end of their service life. When this happens, replace them with new batteries. Obtain two AA size manganese or alkaline batteries. You cannot use other batteries except for the AA size manganese or alkaline.

Attention

Make sure you read the following manual before handling the batteries.

s Safety Instructions a Remove the battery cover.

While pushing the battery cover catch, lift the cover up.

Caution

Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.

c Reattach the battery cover.

Press the battery cover until it clicks into place.

Remote control operating range

15 b Replace the old batteries with new batteries.

Preparing the Projector

This chapter explains how to install the projector and connect projection sources.

Installing the Projector

Installation Methods

The projector supports the following four different projection methods.

Install the projector according to the conditions of the installation location.

•

Project images from in front of the screen. (Front projection)

•

Project images from behind a translucent screen. (Rear projec‐ tion)

•

Suspend the projector from a wall or ceiling and project im‐ ages from in front of a screen.

(Front/Ceiling projection)

•

Suspend the projector from the ceiling and project images from behind a translucent screen.

(Rear/Ceiling projection)

Warning

•

A special method of installation is required when suspending the projector from a wall or ceiling. If it is not installed correctly, it could fall causing an accident and injury.

• If you use adhesives on the wall mount plate fixing points or the ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its mount. This could cause serious injury to anyone under the mount and could damage the projector.

When installing or adjusting the mount, do not use adhesives to prevent the screws from loosening and do not use lubricant or oil and so on.

Attention

•

Do not use the projector on its side. This may cause malfunctions to occur.

•

Do not cover the projector's air intake vent or air exhaust vent. If either of the vents are covered, the internal temperature could rise and cause a fire.

a •

When installing the projector on a wall or on the ceiling, make sure you use the correct tools for the installation method.

s


•

You can change the setting as follows by pressing down the [A/V

Mute] button on the remote control for about five seconds.

Front W Front/Ceiling

Rear W Rear/Ceiling

•

Set Rear or Rear/Ceiling from the configuration menu.

s Extended - Projection

p.64

17

Connecting Equipment

The port name, location, and connector orientation differ depending on the source being connected.

Connecting a Computer

To project images from a computer, connect the computer using one of the following methods.

A B When using the supplied computer cable

C

Connect the computer's display output port to the projector's Computer1 or Computer2 port.

You can output audio from the projector's speaker by connecting the computer's audio output port to the projector's Audio1 or Audio2 port using a commercially available audio cable.

When using a commercially available USB cable

D

Connect the computer's USB port to the projector's USB(TypeB) port.

You can send the audio with the projected image.

When using a commercially available HDMI cable

Connect the computer's HDMI port to the projector's HDMI port.


a

You can switch the audio input by using Audio Input .

s Extended - Operation - Audio Input

p.64

18

Connecting Equipment a

You can use the commercially available USB cable to connect the projector to a computer to project images from the computer.This function is called USB

Display.

s


Connecting Image Sources

To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.

A

B

When using a commercially available video cable

Connect the video output port on the image source to the projector's Video port using a commercially available video cable.

You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.

When using a commercially available S-video cable

19


Connect the video output port on the image source to the projector's S-Video port using a commercially available video cable.

You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.

C D When using the optional component video cable s

"Optional Accessories and Consumables" p.118

Connect the component output port on the image source to the projector's Computer1 or Computer2 port.

You can output audio from the projector's speaker by connecting the image source's audio output port to the projector's Audio1 or Audio2 port using a commercially available audio cable.

E When using a commercially available HDMI cable

Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.


a

You can switch the audio input by using Audio Input .


p.64

20


Attention

•

If the input source is on when you connect it to the projector, it could cause a malfunction.

•

If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.

21

Connecting Equipment a •

If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.

•

When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".

Connecting USB Devices

You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.

Using the USB cable supplied with the USB device, connect the USB device to the USB(TypeA) port on the projector.

22

When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.

s

"Slideshow" p.103

If the Document Camera is connected while projecting images from another input port, press the [USB] button on the remote control, or the [Source Search] button on the control panel, to switch to images from the Document Camera.

s

"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.29

a

While projecting images from a USB device, if you want to connect an audio output device, connect it to the Audio2 port.


23

Attention

•

If you use a USB hub, operation may not be performed correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.

•

When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.

•

Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.

•

Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.

Removing USB devices

After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from the projector.

Connecting a microphone

You can output microphone audio from the projector's speaker by connecting a commercially available dynamic microphone.

a • Plug-in-power is not supported.

• Adjust Mic Input Level if the microphone audio is difficult to hear, or if it is too loud resulting in a crackling sound.

s Settings - Mic Input Level

p.63

• Make the following settings to output audio from a microphone when the projector is turned off.

Set Standby Mode to Communication On . s Extended - Standby Mode

p.64

Set Standby Microphone to On . s Extended - Standby Microphone

p.64


Connecting External Equipment

You can output images and audio by connecting an external monitor or speaker.

A When outputting images to an external monitor

Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.

B When outputting audio to an external speaker

Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.

a •

If you set Standby Mode to Communication On , you can output images to an external monitor even if the projector is in standby mode.

s Extended - Standby Mode

p.64

•

Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video signals.

•

Setting gauges for functions such as Keystone, Configuration menu, or Help screens are not output to the external monitor.

•

When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external output.

Connecting a LAN Cable

Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN cable.

24

Connecting Equipment a

To prevent malfunctions, use a category 5 shielded LAN cable.

25


Installing the Optional Wireless LAN Unit

a Remove the stopper fixing screw, and then remove the wireless

LAN unit's stopper.

b Install the Wireless LAN unit.

c To avoid losing the wireless LAN unit, secure the stopper using the stopper fixing screw.

26

Basic Usage

This chapter explains how to project and adjust images.

Projecting images

From Installation to Projection

This section explains the procedure for connecting the projector to a computer with the computer cable and projecting images.

28 e f

Turn on the computer.

Change the computer's screen output.

When using a laptop computer, you need to change the screen output from the computer.

Hold down the Fn key (function key), and press the b

key.

a

The method for changing differs depending on the computer being used. See the documentation supplied with the computer.

If the image is not projected, you can change the projected image using one of the following methods.

•

Press the [Source Search] button on the control panel or the remote control.

s

"Automatically Detect Input Signals and Change the Projected Image

(Source Search)" p.29

•

Press the button for the target port on the remote control.

s

"Switching to the Target Image Using the Remote Control" p.30

a

After projecting the image, adjust the image if necessary.

s

"Correcting Keystone Distortion" p.34

s


a b c d

Remove the lens cover.

Connect the projector to an electrical outlet with the power cable.

Connect the projector to the computer with the computer cable.

Turn on the projector.


Automatically Detect Input Signals and Change the Projected Image (Source Search)

Press the [Source Search] button to project images from the port currently receiving an image.

Because only images from ports receiving an image are projected, you can quickly project the image you want.

Using Remote Control Using the Control Panel a

The following screen is displayed while no image signals are input.

29

Computer1 Computer2 S-Video Video

LAN USB USB Display HDMI

When two or more image sources are connected, press the [Source Search] button until the target image is projected.

When your video equipment is connected, start playback before beginning this operation.


30

Switching to the Target Image Using the Remote

Control

You can change directly to the target image by pressing the following buttons on the remote control.

Remote control

Projecting with USB Display

You can use the commercially available USB cable to connect the projector to a computer to project images from the computer.

You can send the computer's audio with the projected image.

A Each time the button is pressed, it cycles through the following images:

•

Computer1 port

•

Computer2 port

B Each time the button is pressed, it cycles through the following images:

•

S-Video port

•

Video port

•

HDMI port

C Changes to the images projected with EasyMP Network Projection. When projecting using the optional Quick Wireless Connection USB Key, this button switches to that image.

D Each time the button is pressed, it cycles through the following images:

•

USB Display

•

Images from the device connected to the USB(TypeA) port

System requirements

For Windows

OS

CPU

Amount of

Memory

Hard Disk

Free Space

Display

Windows 2000 * 1

Windows XP * 2

Windows Vista

Professional 32 bit, Home Edition 32 bit, Tablet PC Edition 32 bit

Ultimate 32 bit, Enterprise 32 bit,

Business 32 bit, Home Premium 32 bit, Home Basic 32 bit

Windows 7 Ultimate 32/64 bit, Enterprise 32/64 bit, Professional 32/64 bit, Home

Premium 32/64 bit, Home Basic 32 bit, Starter 32 bit

Mobile Pentium III 1.2 GHz or faster

Recommended: Pentium M 1.6 GHz or faster

256 MB or more

Recommended: 512 MB or more

20 MB or more

Resolution of no less than 640x480 and no higher than

1600x1200.

Display color of 16-bit color or greater

* 1 Service Pack 4 only

* 2 Except for Service Pack 1


For Mac OS

OS

CPU

Amount of

Memory

Hard Disk

Free Space

Display

Mac OS X 10.5.1 or later

Mac OS X 10.6.x

Power PC G4 1GHz or faster

Recommended: Core Duo 1.83GHz or faster

512 MB or more

20 MB or more

Resolution of no less than 640x480 and no higher than

1680x1200.

Display color of 16-bit color or greater

31

Connecting for the first time

The first time you connect the projector and the computer using the USB cable, the driver needs to be installed. The procedure is different for

Windows and Mac OS.

a • You do not need to install the driver the next time you connect.

• When inputting images from multiple sources, change the input source to USB Display.

• If you use a USB hub, operation may not be performed correctly.

Connect the USB cable directly to the projector.

For Windows a Connect the computer's USB port to the projector's USB(TypeB) port using a commercially available USB cable.

a

For Windows 2000 or Windows XP, a message asking you if you want to restart your computer may be displayed.Select

No .

For Windows 2000

Double-click Computer , EPSON PJ_UD , and then

EMP_UDSE.EXE

.

For Windows XP

Driver installation starts automatically.

b

For Windows Vista/Windows 7

When the dialog box is displayed, click Run EMP_UDSE.exe

.

When the License Agreement screen is displayed, click Agree .


32 c d

Computer images are projected.

It may take a while for computer images to be projected. Until the computer images are projected, leave the equipment as is and do not disconnect the USB cable or turn off the power of the projector.

Disconnect the USB cable when you are finished.

When disconnecting the USB cable, there is no need to use Safely

Remove Hardware .

a •

If it is not installed automatically, double-click My Computer

- EPSON_PJ_UD - EMP_UDSE.EXE

on your computer.

•

If nothing is projected for some reason, click All Programs -

EPSON Projector - Epson USB Display - Epson USB

Display Vx.xx

on your computer.

•

When using a computer running Windows 2000 under user authority, a Windows error message is displayed and you may not be able to use the software. In this case, try updating

Windows to the latest version, restart, and then try to connect again.

For more details, contact your local dealer or the nearest address provided in the following document.

s Epson Projector Contact List

For Mac OS a Connect the computer's USB port to the projector's USB(TypeB) port using a commercially available USB cable.

The Setup folder of USB Display is displayed in the Finder.

Double-click the USB Display Installer icon.

b c Follow the on-screen instructions to install.

d e f

When the License Agreement screen is displayed, click Agree .

Enter the administrator authority password and start the installation.

When the installation is complete, the USB Display icon is displayed in the Dock and menu bar.

Computer images are projected.

It may take a while for computer images to be projected. Until the computer images are projected, leave the equipment as is and do not disconnect the USB cable or turn off the power of the projector.

When you have finished, select Disconnect from the menu bar or from the USB Display icon on the Dock. You can then disconnect the USB cable.

a • If the USB Display setup folder is not displayed automatically in the Finder, double-click EPSON PJ_UD - USB Display

Installer on your computer.

• If nothing is projected for some reason, click the USB

Display icon in the Dock.

• If there is no USB Display icon in the Dock, double-click

USB Display from the Applications folder.

• If you select Exit from the USB Display icon menu on the

Dock, USB Display does not start automatically when you connect the USB cable.

Uninstalling

For Windows 2000 a b c d

Click Start , select Settings , and then click Control Panel .

Double-click Add/Remove Programs .

Click Change or Remove Programs .

Select Epson USB Display and click Change/Remove .


For Windows XP a b c

Click Start , and then click Control Panel .

Double-click Add or Remove Programs .

Select Epson USB Display and click Remove .

For Windows Vista/Windows 7 a b c

Click Start , and then click Control Panel .

Click Uninstall a program under Programs .

Select Epson USB Display and click Uninstall .

For Mac OS a Open the Applications folder, double-click USB Display , and then double-click Tool .

b Run USB Display UnInstaller .

33

Adjusting Projected Images

Correcting Keystone Distortion

You can correct keystone distortion using one of the following methods.

•

H/V-Keystone

Manually correct distortion in the horizontal and vertical directions independently.

H/V-Keystone

Manually correct distortion in the horizontal and vertical directions independently. H/V-Keystone correction is ideal for fine-tuning keystone distortion.

You can use H/V-Keystone to correct the projected image under the following conditions.

Correction angle: approx 15˚ right and left/approx. 15˚ up and down a Press the [ ] or [ ] buttons on the control panel during projection to display the Keystone screen.

34

•

Quick Corner

Manually correct the four corners independently.

b Press the following buttons to correct keystone distortion.

Press the [ w ] or [ v ] buttons to correct vertical distortion.

a

When you correct keystone distortion, the projected image may be reduced.

Press the [Tele] or [Wide] buttons to correct horizontal distortion.


35 a

You can set H/V-Keystone from the Configuration menu.

s Settings - Keystone - H/V-Keystone

p.63

Quick Corner

This allows you to manually correct each of the four corners of the projected image separately.

a Press the [Menu] button while projecting.

s


Using Remote Control Using the Control Panel c Select Quick Corner , and then press the [ ] button.

d Using the [ ], [ ], [ ], and [ ] buttons on the remote control, or the [ ], [ ], [Wide], and [Tele] buttons on the control panel, select the corner to correct, and then press the [ ] button.

b Select Keystone from Settings .


36 e Using the [ ], [ ], [ ], and [ ] buttons on the remote control, or the [ ], [ ], [Wide], and [Tele] buttons on the control panel, correct the position of the corner.

When you press the [ ] button, the screen shown in step 4 is displayed.

If the message "Cannot adjust any further." is displayed while adjusting, you cannot adjust the shape any further in the direction indicated by the gray triangle.

f Repeat procedures 4 and 5 as needed to adjust any remaining corners.

g When you are done, press the [Esc] button to exit the correction menu.

Because Keystone was changed to Quick Corner , the corner selection screen from step 4 is displayed when you press the [ ] and [ ] buttons on the control panel next time. Change Keystone to H/V-Keystone if you want to perform horizontal and vertical correction using the [ ] and [ ] buttons on the control panel.

s

Settings - Keystone - H/V-Keystone

p.63


37 a

If the [Esc] button is held down for about two seconds while the corner selection screen from step 4 is displayed, the following screen is displayed.

Adjusting the Image Position

Press the foot lever to extend and retract the front foot. You can adjust the position of the image by tilting the projector up to 10 degrees.

Reset Quick Corner : Resets the result of Quick Corner corrections.

Switch to H/V-Keystone : Switches the correction method to

H/V-Keystone .

s

"Settings Menu" p.63

a

The larger the angle of tilt, the harder it becomes to focus. Install the projector so that it only needs to be tilted at a small angle.

Adjusting the Image Size

Press the [Wide] and [Tele] buttons on the control panel to adjust the size of the projected image.

Adjusting the Horizontal Tilt

Extend and retract the rear feet to adjust the projector's horizontal tilt.

a

You can also make adjustments from the configuration menu.

s Settings - Zoom

p.63

A Extend the rear foot.


B Retract the rear foot.

Correcting the Focus

You can correct the focus using the focus ring.

•

Adjust the volume from the Configuration menu.

s Settings - Volume

p.63

Caution

Do not start when the volume is set too high.

A sudden increase in volume may cause loss of hearing. Always lower the volume before powering off, so that you can power on and then gradually increase the volume.

38

Adjusting the Volume

You can adjust the volume using one of the following methods.

•

Press the [Volume] buttons on the remote control to adjust the volume.

[ a

] Decreases the volume.

[ b

] Increases the volume.

Remote control

Selecting the Projection Quality (Selecting Color

Mode)

You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.

Dynamic

Mode

Presentation

Theatre

Photo *1

Sports *2 sRGB

Application

Ideal for use in a bright room. This is the brightest mode, and reproduces shadow tones well.

Ideal for making presentations using color materials in a bright room.

Ideal for watching films in a dark room. Gives images a natural tone.

Ideal for projecting still pictures, such as photos, in a bright room. The images are vivid and brought into contrast.

Ideal for watching TV programmes in a bright room. The images are vivid and brought to life.

Ideal for images that conform to the sRGB

g

color standard.


Mode

Blackboard

Whiteboard

Application

Even if you are projecting onto a blackboard

(greenboard), this setting gives your images a natural tint, just like when projecting onto a screen.

Ideal for making presentations using a whiteboard.

* 1 This selection is only available when the input signal is RGB or when the source is USB Display, USB, or LAN.

* 2 This can be selected when inputting component video signals, S-video signals, or composite video signals.

Each time you press the [Color Mode] button, the Color Mode name is displayed on the screen and the Color Mode changes.

Remote control a Press the [Menu] button.

s


Using Remote Control Using the Control Panel b Select Auto Iris from Image .

39 a

You can set Color Mode from the Configuration menu.

s Image - Color Mode

p.60

Setting Auto Iris

By automatically setting the luminance according to the brightness of the displayed image, it lets you enjoy deep and rich images.

c Select On .

The setting is stored for each Color Mode.

d Press the [Menu] button to finish making settings.

a

Auto Iris can only be set when the Color Mode is set to

Dynamic or Theatre .


Changing the Aspect Ratio of the Projected Image

You can change the Aspect Ratio g

of the projected image to suit the type, the ratio of height and width, and the resolution of the input signals.

Available Aspect Modes vary depending on the image signal currently being projected.

Changing methods

Each time you press the [Aspect] button, the Aspect Mode name is displayed on the screen and the aspect ratio changes.

Remote control

A Normal or Auto

B 16:9

C Full

D Zoom

E Native a

You can set the aspect ratio from the Configuration menu.

s Signal - Aspect

p.61

Changing the aspect mode (EB-435W/EB-425W only)

Projecting images from video equipment or from the HDMI port

Each time the [Aspect] button on the remote control is pressed, the aspect mode changes in the order Normal or Auto , 16:9 , Full , Zoom , and

Native .

Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)

Projecting images from a computer

The following shows projection examples for each aspect mode.

Aspect mode

XGA 1024X768(4:3)

Input Signal

WXGA 1280X800(16:10)

Normal

40


Aspect mode

16:9

XGA 1024X768(4:3)

Input Signal

WXGA 1280X800(16:10)

Full

41

Changing the aspect mode (EB-430/EB-420 only)

Projecting images from video equipment

Each time the [Aspect] button on the remote control is pressed, the aspect mode changes in the order 4:3 and 16:9 .

When inputting a 720p/1080i signal and the aspect mode is set to 4:3 , a 4:3 zoom is applied (the right and left sides of the image are cut off).


Zoom

Native a

If parts of the image are missing, set the Resolution setting to Wide or Normal from the Configuration menu, according to the size of the computer panel.

s Signal - Resolution

p.61

A 4:3

B 16:9

Projecting images from the HDMI port

Each time the [Aspect] button on the remote control is pressed, the aspect mode changes in the order Auto , 4:3 , and 16:9 .


A Auto


B 4:3

C 16:9

Projecting images from a computer

Each time the [Aspect] button on the remote control is pressed, the aspect mode changes in the order Normal , 4:3 , and 16:9 .

The following shows projection examples for each aspect mode.

Aspect mode

XGA 1024X768(4:3)

Input Signal

WXGA 1280X800(16:10)

Normal

4:3

16:9 a

If parts of the image are missing, set the Resolution setting to Wide or Normal from the Configuration menu, according to the size of the computer panel.


p.61

42

Useful Functions

This chapter explains useful functions for giving presentations and so on, and the security functions.


44

Hiding the Image and Sound Temporarily (A/V

Mute)

You can use this when you want to focus the audience's attention on what you are saying, or if you do not want to show details such as when you are changing between files during presentations from a computer.

a •

If you use this function when projecting moving images, the images and sound continue to be played back by the source, and you cannot return to the point where A/V Mute was activated.

•

Microphone audio is still output even when A/V Mute is turned on.

•

You can select the screen displayed when the [A/V Mute] button is pressed from the Configuration menu.

s Extended - Display - A/V Mute

p.64

•

The lamp is still lit during A/V Mute, so the lamp hours continue to accumulate.

Each time you press the [A/V Mute] button, A/V Mute turns on or off.

Remote control

Freezing the Image (Freeze)

When Freeze is activated on moving images, the frozen image continues to project on the screen, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the Freeze function is activated beforehand.

Each time you press the [Freeze] button, Freeze turns on or off.

Remote control


45 a •

Audio does not stop.

•

For moving images, the images continue to play back while the screen is frozen, so it is not possible to resume projection from the point where the screen was frozen.

•

If the [Freeze] button is pressed while the Configuration menu or the Help screen is displayed, the menu or the Help screen that is displayed is closed.

•

Freeze still works while E-Zoom is being used.

Pointer Function (Pointer)

This allows you to move a pointer icon on the projected image, and helps you draw attention to the area you are talking about.

b Move the Pointer icon ( ).

Remote control

When any pair of adjacent [ ], [ ], [ ], or [ ] buttons are pressed at the same time, the pointer can be moved diagonally.

a

You can select the shape of the pointer icon from the

Configuration menu.

s Settings - Pointer Shape

p.63

a Display the Pointer.

Each time you press the [Pointer] button, the pointer appears or disappears.

Remote control


Enlarging Part of the Image (E-Zoom)

This is useful when you want to expand images to see them in greater detail, such as graphs and tables.

46 b Move the Cross ( ) to the area of the image that you want to enlarge.

Remote control a Start E-Zoom.

Press the [ z

] button to display the Cross ( ).

Remote control


c Enlarge.

Remote control

[ z ] button: Expands the area each time it is pressed. You can expand quickly by holding the button down.

[ x ] button: Reduces images that have been enlarged.

[Esc] button: Cancels E-Zoom.

a • The enlargement ratio appears on the screen. The selected area can be enlarged to between 1 to 4 times in 25 incremental steps.

•

During enlarged projection, press the [ ], [ ], [ ], and

[ ] buttons to scroll the image.


47

Using the Remote Control to Operate the Mouse

Pointer (Wireless Mouse)

When the USB port of a computer and the USB(TypeB) port on the projector are connected with a commercially available USB cable, you can use the remote control to control the computer's mouse pointer.

Once the connection has been made, the mouse pointer can be operated as follows.

Moving the mouse pointer

[ ][ ][ ][ ] buttons:

Moves the mouse pointer.

Mouse clicks

This is available when projecting images from a computer connected to the

Computer1, Computer2, or HDMI ports.This is also available when projecting in USB Display.

The following operating systems are compatible with Wireless Mouse.

OS

Windows

Windows 98

Windows 98SE

Windows Me

Windows 2000

Windows XP

Windows Vista

Windows 7

Mac OS

Mac OS X 10.3.x

Mac OS X 10.4.x

Mac OS X 10.5.x

Mac OS X 10.6.x

It may not be possible to use the Wireless Mouse function under some versions of the operating systems.

Drag and drop

Page Up/Down

[ ] button: Left click. Press quickly twice to double-click.

[Esc] button: Right click.

While holding down the [ ] button, press the [ ], [ ], [ ], and [ ] buttons.

Release the [ ] button to drop at the desired location.

[ [ ] button: Moves to the previous page.

[ ] ] button: Moves to the next page.


48 a

•


• If the mouse button settings are set to reverse on the computer, the operation of the remote control buttons will also be reversed.

•

The Wireless Mouse function does not operate under the following conditions.

- When the configuration menu or a Help screen is displayed

- When operating functions other than the Wireless Mouse function

(such as adjusting the volume).

However, when using the E-Zoom or Pointer function, the page up or down function is available.

Saving a User's Logo

You can save the image that is currently being projected as a User's Logo.

You can use the registered user's logo as a display when projection starts or no image signal is being input.

s

Extended - Display

p.64

a

Once a User Logo has been saved, the logo cannot be returned to the factory default.

a Project the image you want to save as the User's Logo, and then press the [Menu] button.

s


Using Remote Control Using the Control Panel b Select User's Logo from Extended .


49 d Move the box to select the part of the image to use as the User's

Logo.

You can perform the same operations from the projector's control panel.

Remote control a •

When User's Logo Protect from Password Protect is set to

On , a message is displayed and the User's Logo cannot be changed. You can make changes after setting User's Logo

Protect to Off .

s


•

If User's Logo is selected when Keystone, E-Zoom, Aspect, or

Adjust Zoom is being performed, the function currently being performed is cancelled.

c When the message "Choose this image as the User's Logo?" is displayed, select Yes .

a

When you press the [ ] button on the remote control or the control panel, the screen size may change depending on the signal to match the actual resolution of the image signal.

a

You can save at 400x300 dots in size.

e When you press the [ ] button and the message "Select this image?" is displayed, select Yes .

Projection Functions f Select the zoom factor from the zoom setting screen.

50 a

When a User Pattern is saved, the previous User Pattern is erased.

a Project the image you want to use as the User Pattern, and then press the [Menu] button.

s


Using Remote Control Using the Control Panel g When the message "Save this image as the User's Logo?" is displayed, select Yes .

The image is saved. After the image has been saved, the message

"Completed." is displayed.

a •

When a User's Logo is saved, the previous User's Logo is erased.

•

It takes a while to save. Do not operate the projector or any connected equipment while it is saving, otherwise malfunctions may occur.

Saving User Pattern

There are four types of patterns registered to the projector, such as ruled lines and grid patterns.

s

Settings - Pattern - Pattern Type

p.63

You can also save the image that is currently being projected as a User

Pattern.

b Select Pattern from Settings .

c Select User Pattern .

Projection Functions a

If User Pattern is selected when Keystone, E-Zoom, Aspect, or

Adjust Zoom is being performed, the function currently being performed is cancelled.

d When "Do you want to use the currently projected image as the

User Pattern?" is displayed, select Yes .

e When you press the [ ] button, the message "Do you want to use the currently projected image as the User Pattern?" is displayed.

Then, select Yes .

The image is saved. After the image has been saved, the message

"The User Pattern setting is complete." is displayed.

a •

Once a User Pattern has been saved, User Pattern cannot be returned to the factory default.

•

It takes a while to save a User Pattern. Do not operate the projector or any connected equipment while it is saving, otherwise malfunctions may occur.

51

Security Functions

52

The projector has the following enhanced security functions.

•

Password Protect

You can limit who can use the projector.

•

Control Panel Lock

You can prevent people changing the settings on the projector without permission.

s


•

Anti-Theft Lock

The projector is equipped with the following anti-theft security device.

s


•

User's Logo Protect

Even if someone tries to change the User's Logo set by the owner of the projector, it cannot be changed. When User's Logo Protect is set to On , the following setting changes for the User's Logo are prohibited.

•

Capturing a User's Logo

•

Setting Display Background , Startup Screen , or A/V Mute from

Display s

Extended - Display

p.64

•

Network Protect

When Network Protect is set to On , changing the settings for Network is prohibited.

s

"Network Menu" p.66

Managing Users (Password Protect)

When Password Protect is activated, people who do not know the password cannot use the projector to project images even if the projector power is on.

Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft device as the projector cannot be used even if it is stolen. At the time of purchase,

Password Protect is not activated.

Setting Password Protect

Use the following procedure to set Password Protect.

a During projection, hold down the [Freeze] button for about five seconds.

The Password Protect setting menu is displayed.

Remote control

Kinds of Password Protect

The following three kinds of Password Protect settings can be made according to how the projector is being used.

•

Power On Protect

When Power On Protect is On , you need to enter a preset password after the projector is plugged in and turned on (this also applies to Direct

Power On). If the correct password is not entered, projection does not start.


53 a •

If Password Protect is already activated, you must enter the password.

If the password is entered correctly, the Password Protect setting menu is displayed.

s

"Entering the Password" p.53

•

When the password is set, stick the supplied password protect sticker in a visible position on the projector as a further theft deterrent.

b Select the type of Password Protect you want to set, and then press the [ ] button.

(3) While holding down the [Num] button, enter a four digit number using the numeric buttons. The number entered is displayed as " * * * * ". When you enter the fourth digit, the confirmation screen is displayed.

Remote control

(4) Re-enter the password.

"Password accepted." is displayed.

If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.

c Select On , and then press the [ ] button.

Press the [Esc] button, the screen displayed in step 2 is displayed again.

d Set the password.

(1) Select Password , and then press the [ ] button.

(2) When the message "Change the password?" is displayed, select Yes and then press the [ ] button. The default password is set to "0000". Change this to your own desired Password. If you select No , the screen displayed in step 2 is displayed again.

Entering the Password

When the password entry screen is displayed, enter the password using the numeric buttons on the remote control.

While holding down the [Num] button, enter the password by pressing the numeric buttons.


54

When you enter the correct password, Password Protect is temporarily released.

Attention

• If an incorrect password is entered three times in succession, the message

"The projector's operation will be locked." is displayed for approximately five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password.

• If you have forgotten the password, make a note of the " Request Code : xxxxx" number that appears on the screen and contact the nearest address provided in the Epson Projector Contact List.


• If you continue to repeat the above operation and input the wrong Password thirty times in succession, the following message is displayed and the projector does not accept any more Password entries. "The projector's operation will be locked. Contact Epson as described in your documentation." s Epson Projector Contact List

Restricting Operation (Control Panel Lock)

Do one of the following to lock the operation buttons on the control panel.

•

Full Lock

All of the buttons on the control panel are locked. You cannot perform any operations from the control panel, including turning the power on or off.

•

Partial Lock

All of the buttons on the control panel, except for the [ t

] button, are locked.

This is useful at events or shows when you want to deactivate all buttons during projection or at schools when you want to limit button operation.

The projector can still be operated using the remote control.

a Press the [Menu] button while projecting.

s


Using Remote Control Using the Control Panel b Select Control Panel Lock from Settings .

c Select either Full Lock or Partial Lock according to your purpose.


55 d Select Yes when the confirmation message is displayed.

The control panel buttons are locked according to the setting you chose.

a

You can release the control panel lock by one of the following two methods.

• Select Off from Control Panel Lock .

s Settings - Control Panel Lock

p.63

• Press and hold down the [ ] button on the control panel for about seven seconds, a message is displayed and the lock is released.

Anti-Theft Lock

The projector is equipped with the following types of anti-theft security devices.

•

Security slot

The security slot is compatible with the Microsaver Security System manufactured by Kensington.

See the following for more details on the Microsaver Security System.

s http://www.kensington.com/

• Security cable installation point

A commercially available theft-prevention wire lock can be passed through the installation point to secure the projector to a desk or pillar.

Installing the wire lock

Pass an anti-theft wire lock through the installation point.

See the documentation supplied with the wire lock for locking instructions.

Configuration Menu

This chapter explains how to use the Configuration menu and its functions.

Using the Configuration Menu

This section explains how to use the Configuration menu.

Although steps are explained using the remote control as an example, you can perform the same operations from the control panel. Check the guide under the menu for the available buttons and their operations.

a Display the Configuration menu screen.

c Select a submenu item.

d Change settings.

b Select a top menu item.

e Press the [Menu] button to finish making settings.

57

List of Functions

Configuration Menu Table

Settable items vary depending on the model being used and the image signal and source being projected.

Top Menu Name

Image menu s

p.60

Signal menu s

p.61

Submenu Name Items or Setting Values

Color Mode

Brightness

Contrast

Color Saturation

Tint

Sharpness

Abs. Color Temp.

Color Adjustment

Dynamic, Presentation, Theatre,

Photo, Sports, sRGB, Blackboard, and Whiteboard

-24 - 24

-24 - 24

-32 - 32

-32 - 32

-5 - 5

5000K to 10000K

Red: -16 to 16

Green: -16 to 16

Blue: -16 to 16

Auto Iris

Auto Setup

Resolution

Tracking

Sync.

Position

Progressive

Noise Reduction

On and Off

On and Off

-

-

Auto, Wide, and Normal

Up, Down, Left, and Right

Off, Video, and Film/Auto

Off, NR1, and NR2

HDMI Video Range Auto, Normal, and Expanded

Input Signal Auto, RGB, and Component

58

Top Menu Name

Settings menu s

p.63

Extended menu s

p.64

Submenu Name

Video Signal

Aspect

Overscan

Keystone

Zoom

Control Panel Lock

Remote Receiver

User Button

Pattern

Display

User's Logo

Projection

Items or Setting Values

Auto, NTSC, NTSC4.43, PAL,

M-PAL, N-PAL, PAL60, and

SECAM

Normal, Auto, 4:3, 16:9, Full,

Zoom, and Native

Auto, Off, 4%, and 8%

H/V-Keystone and Quick Corner

0 (Wide) to 40 (Tele)

Full Lock, Partial Lock, and Off

Pointer Shape Pointer 1, Pointer 2, Pointer 3

Power Consumption Normal and ECO

Volume

Mic Input Level

0 - 20

0 - 5

Front/Rear, Front, Rear and Off

Power Consumption, Info,

Progressive,Test Pattern,

Resolution, Mic Input Level, and

Pattern Display

-

Pattern Display, Pattern Type,

User Pattern, and Test Pattern

Messages, Display Background,

Startup Screen, and A/V Mute

Operation

Standby Mode

Front, Front/Ceiling, Rear, and

Rear/Ceiling

Direct Power On, Sleep Mode,

Sleep Mode Timer, High

Altitude Mode, and Audio Input

Communication On and

Communication Off


Top Menu Name

Info menu s

p.74

Reset menu s

p.75

Submenu Name Items or Setting Values

Standby Microphone On and Off

Language 15 or 35 languages * 1

Lamp Hours

Source

Input Signal

Resolution

-

-

-

-

Video Signal

Refresh Rate

Sync Info

Status

Serial Number

Event ID

Reset All

Reset Lamp Hours

-

-

-

-

-

-

-

-

* 1 The number of supported languages differs depending on the region where the projector is used.

Network menu

Top Menu Name

Basic menu s

p.68

Wireless LAN menu s

p.68

Submenu Name

Projector Name

PJLink Password

Web Control Password -

-

-

Projector Keyword

Wireless LAN Power


On and Off

On and Off

Connection Mode

Channel

Quick and Advanced

1ch, 6ch, and 11ch

59

Top Menu Name

Security menu s

Wired LAN menu s s

p.70

p.71

Mail menu

p.72

Others menu s

p.73

Submenu Name

Wireless LAN Sys.

SSID Auto Setting

SSID

IP Settings

SSID Display

IP Address Display

Security


802.11b/g and 802.11b/g/n

-

On and Off

DHCP, IP Address, Subnet Mask, and Gateway Address

On and Off

On and Off

No, WEP, WPA-PSK, and WPA2-

PSK

128Bit and 64Bit

ASCII and HEX

-

1, 2, 3, 4

WEP Encryption

Format

Key ID

Encryption Key 1, En‐ cryption Key 2, Encryp‐ tion Key 3, and Encryp‐ tion Key 4

Authentication Type

PSK

IP Settings

IP Address Display

Mail Notification

SMTP Server

Port Number

Address 1 Setting, Ad‐ dress 2 Setting, and Ad‐ dress 3 Setting

SNMP

-

Open and Shared

DHCP, IP Address, Subnet Mask, and Gateway Address

-

-

-

On and Off

On and Off

On and Off


Top Menu Name Submenu Name

Trap IP Address 1 and

Trap IP Address 2

-


Priority Gateway Wired LAN and Wireless LAN

AMX Device Discovery On and Off

Crestron RoomView

Bonjour

On and Off

On and Off

Image Menu

Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.

60 s



Sub-menu

Color Mode

Function

You can select the quality of the image to suit your surroundings.

s

"Selecting the Projection Quality (Selecting Color Mode)" p.38

Brightness

Contrast

You can adjust the image brightness.

You can adjust the difference between light and dark in the images.

Color Saturation You can adjust the color saturation for the images.

Tint

Sharpness

You can adjust the image tint.

You can adjust the image sharpness.

Abs. Color Temp.

(This item cannot be selected if Color Mode is set to sRGB

g .)

You can adjust the overall tint of the image.You can adjust tints in

10 stages from 5000 K to 10000 K. The image is tinted blue when a high value is selected and tinted red when a low value is selected.


61

Sub-menu

Color Adjustment

Auto Iris

Reset

Function

(This item cannot be selected if Color Mode is set to sRGB

g .)

You can adjust the color strength for Red, Green , and Blue individually.

(This item can be set only if Color Mode is set to Dynamic or

Theatre .)

Set to On to adjust the iris to obtain the optimum light for images being projected.

The setting is stored for each Color Mode.

s

"Setting Auto Iris" p.39

You can reset all adjustment values for the Image menu to their default settings. See the following to return all menu items to their default settings.

s

"Reset Menu" p.75

Signal Menu

Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.

You cannot make settings on the Signal menu when the source is USB

Display, USB, or LAN.

s



Sub-menu

Auto Setup

Resolution

Tracking

Function

Set to On to automatically adjust Tracking, Sync., and Position to the optimum state when the input signal changes.

Set to Auto to automatically identify the resolution of the input signal. If images are not projected correctly when set to Auto , for example if some of the image is missing, adjust to Wide for wide screens, or set to Normal for 4:3 or 5:4 screens depending on the connected computer.

You can adjust computer images when vertical stripes appear in the images.


Sub-menu

Sync.

Function

You can adjust computer images when flickering, fuzziness, or interference appear in the images.

Position

Progressive

You can adjust the display position up, down, left, and right when a part of the image is missing so that all of the image is projected.

Interlace

g

(i) signal is converted to Progressive

g (p). (IP

conversion)

Off : Ideal for images with a large amount of movement.

Video : Ideal for general video images.

Film/Auto : This is ideal for movie films, computer graphics, and animation.

Noise Reduction (This cannot be set when a digital RGB signal is input, or when an interlace signal is being displayed when Progressive is set to

Off .)

Smoothes out rough images. There are two modes. Select your favorite setting. It is recommended that this is set to Off when viewing image sources in which noise is very low, such as for

DVDs.

HDMI Video

Range

Input Signal

Video Signal

Aspect

When the projector's HDMI port is connected to a DVD player, the projector's video range is set according to the DVD player's video range setting.

You can select the input signal from the Computer1 port or the

Computer2 port.

If set to Auto , the input signal is set automatically according to the connected equipment.

If colors do not appear correctly when set to Auto , select the appropriate signal according to the connected equipment.

You can select the input signal from the S-Video port or the

Video port. If set to Auto , video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being projected when set to Auto , select the appropriate signal according to the connected equipment.

You can set the aspect ratio

g for projected images.

s

"Changing the Aspect Ratio of the Projected Image" p.40

62

Sub-menu

Overscan

Reset

Function

Changes the output image ratio (the range of the projected image). You can set the cropping range to Off , 4% , or 8% . When the source is HDMI, Auto is available. When Auto is selected, it automatically changes to Off or 8% according to the input signal.

You can reset all adjustment values on the Signal menu to their default settings, except for Input Signal .

See the following to return all menu items to their default settings.

s

"Reset Menu" p.75


Settings Menu

Sub-menu

Keystone

Zoom

Control Panel

Lock

Function

You can correct keystone distortion.

• When H/V-Keystone is selected:

Adjust V-Keystone and H-Keystone to correct horizontal and vertical keystone distortion.

• When Quick Corner is selected:

Select and correct the four corners of the projected image.

s

"Quick Corner" p.35

Adjusts the projected image size.

You can use this to restrict operation of the projector's control panel.

s


63

Sub-menu

Pointer Shape

Function

You can select the shape of the pointer.

Pointer 1:

Pointer 2:

Power Consumption

Volume

Pointer 3: s

"Pointer Function (Pointer)" p.45

You can set the lamp brightness to one of two settings.

Select ECO if the images being projected are too bright, such as when projecting images in a dark room or onto a small screen.

When ECO is selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and fan rotation noise during projection is reduced.

Electrical consumption: about 16 to 26% decrease, lamp life: about 1.2 to 1.5 times longer

You can adjust the volume. Setting values are saved for each source.

Mic Input Level Adjust this if the microphone input level is low and the microphone audio output from the projector's speaker is difficult to hear, or if the input level is too high, resulting in a crackling sound in the audio from the microphone.When Mic Input Level is turned down to 0, no microphone audio is output from the speaker.

When the microphone input level is raised, the audio from the connected device becomes quieter. When the microphone input level is lowered, the audio from the connected device becomes louder.

Remote Receiver You can limit the reception of the operation signal from the remote control.

When set to Off , you cannot perform any operations from the remote control. If you want to make operations from the remote control, hold down the [Menu] button on the remote control for at least 15 seconds to reset the setting to its default value.


64

Sub-menu

User Button

Pattern

Function

You can select the item assigned from the Configuration menu with the remote control's [User] button. By pressing the [User] button the assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/ adjustments. You can assign one of the following items to the [User] button.

Power Consumption , Info , Progressive , Test Pattern ,

Resolution , Mic Input Level , and Pattern Display

Pattern Display : Display a pattern.

Pattern Type : You can select from Patterns 1 to 4 or User

Pattern. Patterns 1 to 4 display projection lines such as ruled lines or a grid.

Pattern 2: Pattern 1:

Pattern 3: Pattern 4:

Sub-menu

Reset

Function

You can reset all adjustment values in the Settings menu to their default settings, except for Zoom and User Button .


s

"Reset Menu" p.75

Extended Menu

User Pattern : Captures a user pattern.

s

"Saving User Pattern" p.50

Test Pattern : When the projector is set up, a test pattern is displayed so that you can adjust the projection status without connecting equipment. While the test pattern is displayed, zoom, focus adjustments, and keystone correction can be performed.

To cancel the Test Pattern, press the [Esc] button on the remote control or the control panel.

Attention

If a pattern is displayed for a long time, a residual image may be visible in projected images.


Sub-menu

Display

User's Logo *1

Projection

Function

You can make settings related to the projector's display.

Messages : When set to Off , the following items will not be displayed.

Item names when the Source, Color Mode, or Aspect Ratio is changed, messages when no signal is being input, and warnings such as High Temp Warning.

Display Background * 1 : You can set the screen status for when no image signal is available to Black , Blue , or

Logo .

Startup Screen * 1 : Set to On to display the User's Logo when projection starts.

A/V Mute * 1 : You can set the screen displayed when the remote control's [A/V Mute] button is pressed to Black ,

Blue , or Logo .

You can change the user's logo that is displayed as a background during Display Background, A/V Mute, and so on.

s

"Saving a User's Logo" p.48

Select from one of the following projection methods depending on how the projector is installed.

Front , Front/Ceiling , Rear , and Rear/Ceiling

You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.

Front W Front/Ceiling

Rear W Rear/Ceiling s

"Installation Methods" p.17

65

Sub-menu

Operation

Function

Direct Power On : Set to On to turn on the projector simply by plugging it in.

When the power cable is plugged in, note that the projector turns on automatically in cases such as a power outage being restored.

Sleep Mode : When this is set to On , the power is turned off automatically when no image signal is input and no operation is performed within a certain amount of time.

Sleep Mode Timer : When Sleep Mode is set to On , you can set the time before the projector automatically turns off within a range of 1 to 30 minutes.

High Altitude Mode : Set this to On when using the projector at an altitude of 1500 m or above.

Audio Input : When set to Auto , audio for the image currently being projected is output.If anything other than

Auto is selected, audio for the selected audio input port is output.When the input source is HDMI, USB Display, or

LAN, the audio for the image currently being projected is output regardless of the Audio Input setting.

Standby Mode If you set Communication On , you can perform the following operations even if the projector is in standby mode.

• Monitoring and controlling the projector over the network.

s

"Monitoring and Controlling" p.108

•

Outputting analog RGB signals from the Computer1 port to an external monitor.

• Outputting audio from the microphone to the projector's speaker.

(Only when the Standby Microphone is set to On .) s

"Connecting Image Sources" p.19

Standby Microphone

(This item is settable only when Standby Mode set to

Communication On .)

When set to On , you can output audio from the microphone from the projector's speaker even if the projector is in standby mode.


66

Sub-menu

Language

Reset

Function

You can set the language for messages and menus.

You can reset the adjustment values for Display * 1 and

Operation * 2 from the Extended menu to their default settings.


s

"Reset Menu" p.75

* 1 When User's Logo Protect is set to On in Password Protect , settings related to user's logo cannot be changed. You can make changes after setting User's

Logo Protect to Off .

s


* 2 Except for High Altitude Mode.

Network Menu

When Network Protect is set to On in Password Protect , a message is displayed and the network settings cannot be changed. Turn Network

Protect Off and then configure the network.

s


Sub-menu

Net. Info. - Wireless LAN

Net. Info. -

Wired LAN

Network Configuration

Function

Displays the following network setting status information.

•

Connection Mode

•

Antenna Level

•

Projector Name

•

SSID

•

DHCP

•

IP Address

•

Subnet Mask

•

Gateway Address

•

MAC Address

•

Region Code *

Displays the following network setting status information.

•

Projector Name

•

DHCP

•

IP Address

•

Subnet Mask

•

Gateway Address

•

MAC Address

The following menus are available for setting network items.

Basic , Wireless LAN , Security , Wired LAN , Mail , Others ,

Reset , and Setup complete

* Displays available region information for the Wireless LAN unit being used.

For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.

s Epson Projector Contact List a

By using a Web browser of a computer connected to the projector on a network, you can set functions and control the projector. This function is called Web Control. You can easily enter text using a keyboard to make settings for Web Control such as Security settings.

s

"Changing Settings Using a Web Browser (Web Control)" p.108


Notes on operating the Network menu

Selecting from the top menu and sub menus, and changing selected items is the same as making operations from the Configuration menu.

When done, make sure you go to the Setup complete menu, and select one of Yes , No , or Cancel . When you select Yes or No , you return to the

Configuration menu.

67

Yes : Saves the settings and exits the Network menu.

No : Does not save the settings and exits the Network menu.

Cancel : Continues displaying the Network menu.

Soft keyboard operations

The Network menu contains items that require input of alphanumerics during setup. In this case, the following software keyboard is displayed.Use

the [ ], [ ], [ ], and [ ] buttons on the remote control or the [ ],

[ ], [Wide], and [Tele] buttons on the control panel to move the cursor to the desired key, and then press the [ ] button to enter the alphanumeric character. Enter figures by holding down the [Num] button on the remote control, and pressing the numeric buttons. After inputting, press Finish on the keyboard to confirm your input. Press Cancel on the keyboard to cancel your input.

•

Each time the CAPS key is selected and the [ ] button is pressed, it sets and changes between upper case and lower case letters.

•

Each time the SYM1/2 key is selected and the [ ] button is pressed, it sets and changes the symbol keys for the section enclosed by the frame.


Basic menu

68

Sub-menu

Projector Keyword

Function

When set to On , you have to enter the keyword when you try to connect the projector to a computer via a network. As a result, you can prevent presentations from being interrupted by connections from other computers.

Normally this should be set to On .


Wireless LAN menu

Sub-menu Function

Projector Name Displays the projector name used to identify the projector when connected to a network.

When editing, you can enter up to 16 single-byte alphanumeric characters.

PJLink Password Set a password to use when you access the projector using compatible PJLink software.

You can enter up to 32 single-byte alphanumeric characters.

Web Control

Password

Set a password to use when making settings and controlling the projector using Web Control. Enter no more than eight singlebyte alphanumeric characters. Web Control is a computer function that allows you to set up and control the projector by using the Web browser on a computer connected on a Network.

s


Sub-menu

Wireless LAN

Power

Function

Turn On when connecting the projector to the computer over wireless LAN.

If you do not want to connect via wireless LAN, turn it Off to prevent unauthorized access by others.

This is set to On by default.


Sub-menu

Connection

Mode

Channel

Wireless LAN

Sys.

SSID Auto Setting

SSID

Function

Set the connection mode when using EasyMP Network

Projection to connect the projector and computer.

This is set to Quick by default.

See the following manual for details on Connection Mode.


(This can only be set if Connection Mode is set to Quick .)

Select the frequency band used by the wireless LAN from 1ch ,

6ch , or 11ch .

This is set to 11ch by default.

Set the Wireless LAN Sys. to either 802.11b/g or 802.11b/g/n .

The default value is 802.11b/g/n .

(This can only be set if Connection Mode is set to Quick .)

Set to On to speed up the projector search.

Set to Off when connecting to multiple projectors at the same time.

This is set to On by default.

(This can be set only if SSID Auto Setting is set to Off .)

Enter an SSID g . When an SSID is provided for the wireless LAN

system in which the projector participates, enter the SSID.

You can enter up to 32 single-byte alphanumeric characters.

69

Sub-menu

IP Settings

SSID Display

IP Address Display

Function

(This can be set only if Connection Mode is set to Advanced .)

You can make network settings.

DHCP : Set to On

to make network settings using DHCP g . If this

is set to On , you cannot set any more addresses.

IP Address

: You can input the IP address g

assigned to the projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.

0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

Subnet Mask : You can input the subnet mask

g for the projector.

You can enter a number from 0 to 255 in each field of the address.

However, the following subnet masks cannot be used.

0.0.0.0, 255.255.255.255

Gateway Address : You can input the IP address for the gateway for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following Gateway addresses

g

cannot be used.


To prevent the SSID

g from being displayed on the LAN Standby

screen, set this to Off .

To prevent the IP address g from being displayed on the LAN

Standby screen, set this to Off .


Security menu

Sub-menu

Security

Function

Select the security type from the items that are displayed.

When setting security, follow the instructions from the administrator of the network system you are about to access.

WEP Encryption You can set the encryption method for WEP encryption.

128Bit : Uses 128 (104) bit encoding.

64Bit : Uses 64 (40) bit encoding.

Format

Key ID

You can set the input method for the WEP encryption key to

ASCII or HEX .

You can select the WEP encryption ID key.

70

Sub-menu

Encryption Key

1/Encryption Key

2/Encryption Key

3/Encryption Key

4

Authentication

Type

PSK

Function

You can enter the key used for WEP encryption. Enter the key in single-byte characters following instructions from the network administrator for the network in which the projector participates. The type of character and the number that can be entered differ according to the WEP Encryption and Format settings.

128Bit - ASCII : Single-byte alphanumerics, 13 characters.

64Bit - ASCII : Single-byte alphanumerics, 5 characters.

128Bit - HEX : 0 to 9 and A to F, 26 characters.

64Bit - HEX : 0 to 9 and A to F, 10 characters.

Set the WEP authentication type.

Open : Uses open system authentication.

Shared : Uses shared key authentication.

(This can only be set when WPA-PSK or WPA2-PSK are selected from Security .)

You can enter a Pre-Shared Key (encrypted key) in single-byte alphanumeric characters. Enter at least 8 and up to 32 characters.

Type of security

When the optional wireless LAN unit is installed and being used in

Advanced connection mode, it is strongly recommended that you set security. Select one of the following security methods.

•

WEP

Data is encrypted with a code key (WEP key). This mechanism prevents communication unless the encryption keys for the access point and the projector match.


•

WPA

This is an encryption standard that improves security which is a weak point of WEP. Although there are multiple kinds of WPA encryption methods, this projector uses TKIP and AES.

WPA also includes user authentication functions. WPA authentication provides two methods: using an authentication server, or authenticating between a computer and an access point without using a server. This projector supports the latter method, without a server.

a

For setting details, follow the directions from the network administrator of your network.

Wired LAN menu

71


72

Sub-menu

IP Settings

IP Address Display

Function

You can make settings related to the following addresses.

DHCP

g

: Set to On to configure the network using DHCP. If this is set to On , you cannot set any more addresses.

IP Address g

: You can input the IP address assigned to the projector. You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.


Subnet Mask g : You can input the subnet mask for the projector.

You can input a number from 0 to 255 in each field of the address.

However, the following subnet masks cannot be used.

0.0.0.0, 255.255.255.255

Gateway Address

g : You can input the IP address for the gateway

for the projector. You can input a number from 0 to 255 in each field of the address. However, the following gateway addresses cannot be used.


To prevent the IP address from being displayed on Network Info in the Network menu and on the LAN Standby screen, set this to

Off .

Mail menu

When this is set, you receive an email notification if a problem or warning occurs in the projector.

s

"Using the Mail Notification Function to Report Problems" p.111

Sub-menu

Port Number

Function

Mail Notification Set to On to send an email to the preset addresses when a problem or warning occurs with a projector.

SMTP Server You can input the IP address

g for the SMTP server for the

projector.

You can enter a number from 0 to 255 in each field of the address.

However, the following IP addresses cannot be used.

127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from

0 to 255)

You can input the port number for the SMTP server. The default value is 25. You can input numbers between 1 to 65535.


Sub-menu

Address 1 Setting/Address 2

Setting/Address

3 Setting

Function

You can input the email address of the destination to send the notification email to. You can register up to three destinations.

You can enter up to 32 single-byte alphanumeric characters for the email addresses.

The address for destination 1 is the mail notification sender's address.

You can select the problems or warnings to be notified about by email. When the selected problem or warning occurs in the projector, an email is sent to the specified destination address notifying that a problem or warning has occurred. You can select multiple items from the displayed items.

Others menu

73

Sub-menu

SNMP

Function

Set to On to monitor the projector using SNMP.

To monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a network administrator.

The default value is Off .

Trap IP Address

1/Trap IP Address 2

You can register up to two IP addresses for the SNMP trap notification destination. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

Priority Gateway You can set the priority gateway to a Wired LAN or Wireless

LAN .


74

Sub-menu

AMX Device Discovery

Crestron Room-

View

Bonjour

Function

When the projector is connected to a network, set this to On to allow the projector to be detected by AMX Device

Discovery g

.Set this to Off if you are not connected to an environment controlled with a controller from AMX or AMX

Device Discovery.

Set this to On only when monitoring or controlling the projector over the network using Crestron RoomView ® . Otherwise, set this to Off .

s

"About Crestron RoomView ® " p.114

When this is set to On , the following functions are not available.

•

Web control

•

Message Broadcasting (EasyMP Monitor Plug-in)

Set this to On when connecting to the network using Bonjour.

See Apple's Web site for more information on the Bonjour service.

http://www.apple.com/

Reset menu

Resets all of the network settings.

Sub-menu

Reset network settings.

Function

To reset all of the Network settings, select Yes .

Info Menu (Display Only)

Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the source currently being projected. Depending on the model used, some input sources are not supported.


75 s



Sub-menu

Status

Serial Number

Event ID

Function

This information is about errors that have occurred with the projector.

It may be needed if service is required.

Displays the projector's serial number.

Displays the application error log.

s

"About Event ID" p.92

* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", and so on.

Reset Menu

Sub-menu

Lamp Hours

Source

Input Signal

Resolution

Video Signal

Refresh Rate

Sync Info

Function

You can display the cumulative lamp operating time * .

When it reaches the lamp warning time, the characters are displayed in yellow.

You can display the source name for the connected equipment currently being projected.

You can display the content of Input Signal set in the

Signal menu according to the source.

You can display the resolution.

You can display the settings for Video Signal in the Signal menu.

You can display the refresh rate

g

.

You can display the image signal Information.

It may be needed if service is required.

Sub-menu

Reset All

Function

You can reset all items in the Configuration menu to their default settings.

The following items are not reset to their defaults: Input Signal ,

Zoom , User's Logo , all items for Network menus, Lamp Hours ,

Language , and Password .


Sub-menu

Reset Lamp

Hours

Function

Clears the cumulative lamp hours use time. Reset this when you replace the lamp.

76

Troubleshooting

This chapter describes how to identify problems and what to do if a problem is found.

Using the Help

If a problem occurs with the projector, the Help screen is displayed to assist you by pressing the Help button. You can solve problems by answering the questions.

a Press the [Help] button.

The Help screen is displayed.

Using Remote Control Using the Control Panel c Confirm the selection.

Using Remote Control Using the Control Panel

78

Questions and solutions are displayed as shown on the screen below.

Press the [Help] button to exit the Help.

b Select a menu item.

a

See the following if the Help function does not provide a solution to the problem.

s

"Problem Solving" p.79

Using Remote Control Using the Control Panel

Problem Solving

If you are having a problem with the projector, first check the projector's indicators and see "Reading the Indicators".

See the following if the indicators do not show clearly what the problem might be.

s

"When the Indicators Provide No Help" p.82

Reading the Indicators

The projector is provided with the following three indicators that indicate the operating status of the projector.

A Power indicator

B Lamp indicator

C Temp indicator

Indicates the operating status.

Standby condition

When the [ t ] button is pressed in this condition, projection starts.

Preparing for network monitoring or cool down in progress

All buttons are disabled while the indicator is flashing.

Warming up

Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.

The [ t ] button is disabled during warm-up.

Projecting

Indicates the projection lamp status.

Indicates the internal temperature status.

See the following table for the status of indicators and how to resolve the problems.

79

Problem Solving

80

If all indicators are off, the power cable is not connected correctly or the power is not being supplied.

Sometimes, when the power cable is unplugged, the t

indicator remains lit for a short period, but this is not a fault.

Status Cause

Internal Error

: Lit : Flashing : Off : Varies according to the projector status

Remedy or Status

Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the

Epson Projector Contact List.


Fan Error

Sensor Error

High Temp Error

(overheating)

Lamp Error

Lamp Failure




The lamp turns off automatically and projection stops. Wait for approximately five minutes. After approximately five minutes the projector switches to standby mode, so check the following two points.

•

Check that the air filter and air exhaust vent are not blocked, and that the projector is not positioned against a wall.

• If the air filter is clogged, clean or replace it.

s


,"Replacing the Air Filter" p.99

If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


When using at an altitude of 1500 m or more, set High Altitude Mode to On .

s

"Extended Menu" p.64

Check the following two points.

• Take out the lamp and check whether it is cracked.

s


• Clean the air filter.

s


Problem Solving

81

Status Cause

Auto Iris Error

Power Err.

Remedy or Status

If it is not cracked : Reinstall the lamp and turn on the power.

If the error continues : Replace the lamp with a new one and then turn on the power.

If the error continues : Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


If it is cracked : Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be projected until the lamp is replaced.) s Epson Projector Contact List

When using at an altitude of 1500 m or more, set High Altitude Mode to On .

s

"Extended Menu" p.64




High Temp Warning

Replace Lamp

(This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)

•

Check that the air filter and air exhaust vent are not blocked, and that the projector is not positioned against a wall.

• If the air filter is clogged, clean or replace it.

s


, "Replacing the Air Filter" p.99

Replace it with a new lamp.

s


If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may blow increases. Replace it with a new lamp as soon as possible.

a •

See the following if the projector is not operating properly, even though the indicators are all showing normal.

s

"When the Indicators Provide No Help" p.82

•

If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Problem Solving

When the Indicators Provide No Help

If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.

Problems Relating to Images

• No images appear

Projection does not start, the projection area is completely black, or the projection area is completely blue.

• Moving images are not displayed

Moving images played back from a computer appear black and the images are not projected.

•

Projection stops automatically

•

The message "Not supported" is displayed

•

The message "No Signal" is displayed

•

Images are fuzzy, out of focus, or distorted

•

Interference or distortion appear in images

•

The image is truncated (large) or small, or the aspect ratio is not suitable

Only part of the image is displayed, or the height and width ratios of the image are not correct.

•

Image colors are not right

The whole image appears purplish or greenish, images are black

& white, or colors appear dull.

•

Images appear dark s

p.83

s

p.84

s s s s s s

p.84

p.84

p.84

p.85

p.85

p.86

s

p.87

s

p.87

Problems when Projection Starts

•

The projector does not turn on

Other Problems

• No sound can be heard or the sound is faint s

p.88

s

p.89

•

No sound can be heard from the microphone

•

The remote control does not work

•

I want to change the language for messages and menus

•

Mail is not received even if an error occurs with the projector s

p.89

s

p.90

s

p.90

s

p.90

82

Problem Solving

83

Problems Relating to Images

No images appear

Did you press the [

Is A/V Mute active?

t ] button?

Are all of the indicators off?

Is the lens cover attached?

Check

Are the Configuration menu settings correct?

Is the image to be projected completely black?

(Only when projecting computer images)

Is the image signal format setting correct?

(Only when projecting images from a video source)

Is the USB cable connected correctly?

(Only when projecting USB Display)

Is Windows Media Center displayed in full screen?

(Only when projecting using USB Display or network connection)

Is an application using the Windows DirectX function displayed?

(Only when projecting using USB Display or network connection)

Remedy

Press the [ t ] button to turn the power on.

The power cable is not connected correctly or power is not being supplied.

Connect the projector's power cable correctly.

s


Check the breaker and so on to ensure power is being supplied.

Press the [A/V Mute] button on the remote control to cancel A/V Mute.

s

"Hiding the Image and Sound Temporarily (A/V Mute)" p.44

Remove the lens cover.

Reset all of the settings.

s Reset - Reset All

p.75

Some input images, such as screen savers, may be completely black.

Change the setting according to the signal for the connected equipment.

s Signal - Video Signal

p.61

Check that the USB cable is connected correctly. Reconnect it if it is not connected or not connected properly.

When Windows Media Center is displayed at full screen, you cannot project using USB Display or network connection.

Reduce the screen size.

Applications using the Windows DirectX function may not display images correctly.

Problem Solving

84

Moving images are not displayed (only the moving image portion turns black)

Check

Is the computer's image signal being output to the LCD and the monitor?

(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)

Remedy

Change the image signal from the computer to external output only. Check your computer's documentation, or contact the computer's manufacturer.

Projection stops automatically

Check

Is Sleep Mode set to On ?

Remedy

Press the [ t ] button to turn the power on. If you do not want to use Sleep Mode, change the setting to Off .

s Extended - Operation - Sleep Mode

p.64

The message "Not supported" is displayed.

Check



Do the image signal resolution and refresh rate correspond to the mode?


Remedy



p.61

See the documentation supplied with the computer for how to change the image signal resolution and refresh rate output from the computer.

s

"Supported Monitor Displays" p.122

The message "No Signal" is displayed.

Check

Are the cables connected correctly?

Is the correct port selected?

Remedy

Check that all the cables required for projection are securely connected.

s


Change the image by pressing the [Source Search] button on the remote control or the control panel.

s

"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.29

Problem Solving

85

Check

Is the power of the connected computer or video equipment turned on?

Are the image signals being output to the projector?

(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)

Turn the power on for the equipment.

Remedy

If the image signals are only being output to the computer's LCD monitor or accessory monitor, change the output so that the image signals are also output externally. For some computer models, when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.

If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn the projector and computer off and then back on again.

s


s Computer's documentation

Images are fuzzy, out of focus, or distorted

Check

Is the focus adjusted correctly?

Is the projector at the correct distance?

Is the Keystone adjustment value too large?

Has condensation formed on the lens?

Remedy

Turn the focus ring to adjust the focus.

s


Is it projecting outside of the recommended projection distance range?

Setup within the recommended range.

s

"Screen Size and Projection Distance" p.119

Lower the projection angle to reduce the amount of Keystone correction.

s


If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and wait for the condensation to disappear.

Interference or distortion appear in images

Check



Remedy



p.61

Problem Solving

86

Check


Is an extension cable being used?

Is the correct resolution selected?


Are the Sync.

g and Tracking g

settings adjusted correctly?


Remedy


s


If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to check if the cables you are using may be causing the problem.

Set the computer so that the signals being output are compatible with the projector.

s



Press the [Auto] button on the remote control or the [ ] button on the control panel to perform automatic adjustment.

If the images are not adjusted correctly even after performing automatic adjustment, you can also make adjustments from the Configuration menu.

s Signal - Tracking , Sync.

p.61

Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings , and then clear the

Transfer layered window checkbox.

Is Transfer layered window selected?


The image is truncated (large) or small, or the aspect is not suitable

Check

Is a wide-panel computer image being projected?


Is the image still being enlarged by E-Zoom?

Is the display position adjusted correctly?

Is the computer set for dual display?


Remedy



p.61

Press the [Esc] button on the remote control to cancel E-Zoom.

s


(Only when projecting analog RGB signals input from the Computer1 or Computer2 port)

Press the [Auto] button on the remote control or the [ ] button on the control panel to adjust the position.

You can also adjust the position from the Configuration menu.

s Signal - Position

p.61

If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.

s Computer video driver documentation

Problem Solving

Check

Is the correct resolution selected?


Remedy

Set the computer so that the signals being output are compatible with the projector.

s



Image colors are not right

Check

Do the input signal settings match the signals from the connected device?

Is the image Brightness adjusted correctly?


Is the contrast g adjusted correctly?

Is color adjustment set to an appropriate value?

Are the color saturation and tint adjusted correctly?


Remedy

Change the following settings according to the signal for the connected equipment.

•

When the image is from a device connected to the Computer1 or Computer2 port.

s Signal - Input Signal

p.61

•

When the image is from a device connected to the Video or S-Video port.


p.61

Adjust the Brightness setting from the Configuration menu.

s Image - Brightness

p.60


s


Adjust the Contrast setting from the Configuration menu.

s Image - Contrast

p.60

Adjust the Color Adjustment setting from the Configuration menu.

s Image - Color Adjustment

p.60

Adjust the Color Saturation and Tint settings from the Configuration menu.

s Image - Color Saturation , Tint

p.60

Images appear dark

Check

Is the image brightness set correctly?

Remedy

Adjust the Brightness and Power Consumption settings from the Configuration menu.

s Image - Brightness

p.60

s Settings - Power Consumption

p.63

87

Problem Solving

88

Check

Is the contrast g adjusted correctly?

Is it time to replace the lamp?

Remedy

Adjust the Contrast setting from the Configuration menu.

s Image - Contrast

p.60

When the lamp is nearly ready for replacement, the images become darker and the color quality declines. Replace the lamp with a new one.

s


Problems when Projection Starts

The projector does not turn on

Did you press the [ t ] button?

Are all of the indicators off?

Check Remedy

Press the [ t ] button to turn the power on.

The power cable is not connected correctly or power is not being supplied.

Disconnect and then reconnect the power cable.

s


Check the breaker and so on to ensure power is being supplied.

Do the indicators turn on and off when the power cable is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Is the Control Panel Lock set to Full Lock ?

Press the [ t ] button on the remote control. If you do not want to use Control Panel Lock , change the setting to Off .

s Settings - Control Panel Lock

p.63

Is the remote receiver set correctly?

Check the Remote Receiver from the Configuration menu.

s Settings - Remote Receiver

p.63

Problem Solving

89

Other Problems

No sound can be heard or the sound is faint

Check

Check that the audio/video cable is securely attached to both the projector and audio source.

Is the volume adjusted to the minimum setting?

Is the Mic Input Level set at the maximum?

Is A/V Mute active?

Is the audio cable's specification "No resistance"?

Is it connected with an HDMI cable?

Is Output audio from the projector selected?


Is the correct audio input selected?

Remedy

Disconnect the cable from the audio input port, and then reconnect the cable.

Adjust the volume so that sound can be heard.

s Settings - Volume

p.63

s


Lower the Mic Input Level.

s Settings - Mic Input Level

p.63

Press the [A/V Mute] button on the remote control to cancel A/V Mute.

s


When using a commercially available audio cable, make sure it is labeled "No resistance".

If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.

Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings , and then select

Output audio from the projector .

Check the Audio Input from the configuration menu.


p.64

No sound can be heard from the microphone

Check

Is the microphone connected correctly?

Is the microphone input volume turned down too low?

Remedy

Disconnect the cable from the Mic port, and then reconnect the cable.

s

"Connecting External Equipment" p.24

Adjust the microphone input volume so that sound can be heard. s Settings - Mic Input Level

p.63

Problem Solving

90

The remote control does not work

Check

Is the remote control light-emitting area pointing towards the remote receiver on the projector during operation?

Is the remote control too far from the projector?

Is direct sunlight or strong light from fluorescent lamps shining onto the remote receiver?

Is the correct setting for the

Are the batteries dead or have the batteries been inserted in the wrong direction?

Remote Receiver selected?

Remedy

Point the remote control towards the remote receiver during operation.

s

"Remote control operating range" p.15

The operating range for the remote control is about 6 m.

s

"Remote control operating range" p.15

Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote receiver to

Off from Remote Receiver in the Configuration menu.


p.63

Check the Remote Receiver from the Configuration menu.


p.63

Insert new batteries in the correct direction.

s

"Replacing the remote control batteries" p.15

I want to change the language for messages and menus

Check

Change the language setting.

Remedy

Adjust the Language setting from the Configuration menu.

s Extended - Language

p.64

Mail is not received even if an error occurs with the projector

Is Standby Mode set to

Check

Communication On ?

Did a fatal abnormality occur and the projector come to a sudden stop?

Remedy

To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from the Configuration menu.


p.64

When the projector comes to a sudden stop, email cannot be sent.

If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact

List.


Problem Solving

91

Check

Is power being supplied to the projector?

Is the Mail Notification function set correctly in the Configuration menu?

Remedy

Check that your electrical outlet or power source is functioning correctly.

An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.

s

"Mail menu" p.72

About Event ID

92

Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Event ID

0432

0435

0434

0482

0484

0485

0433

0481

0483

04FE

0479

04FF

0891

0892

0893

0894

0898

Cause

Failed to startup EasyMP Network Projection.

Network communication is unstable.

Cannot play transferred images.

Communication was disconnected from the computer.

EasyMP Network Projection ended unexpectedly.

A system error occurred in the projector.

Cannot find an access point with the same SSID.

The WPA/WPA2 authentication type does not match.

The WEP/TKIP/AES encryption type does not match.

Communication was disconnected because the projector connected to an unauthorized access point.

Failed to acquire DHCP.

Restart the projector.

Remedy

Check the network communication status, and reconnect after waiting for a while.

Restart EasyMP Network Projection.

Check the network communication status, and then restart the projector.

Restart the projector.

Set the computer, the access point, and the projector to the same SSID.

Check that the wireless LAN security settings are correct.

s Security

p.70

Contact your network administrator for more information.

0899 Other communication errors

Check that the DHCP server is operating correctly. If you are not using DHCP, turn off the DHCP setting.

s Wireless LAN - IP Settings

p.68

If restarting the projector or EasyMP Network Projection does not solve the problem, contact your local dealer or the nearest address provided in the Epson

Projector Contact List.


Maintenance

This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.

Cleaning

94

You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.

Attention

Turn off the projector's power before cleaning.

Attention

Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged.

Cleaning the Projector's Surface

Clean the projector's surface by wiping it gently with a soft cloth.

If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and then firmly wring the cloth dry before using it to wipe the projector's surface.

Attention

Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality of the case may change or become discolored.

Cleaning the Air Filter

Clean the air filter and the air intake vent when the following message is displayed.

"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter."

Attention

•

Dust collecting on the air filter may cause the internal temperature of the projector to rise, leading to a malfunction or early deterioration of optical parts. Clean the air filter immediately when the message is displayed.

•

Do not rinse the air filter in water. Do not use detergents or solvents.

Cleaning the Lens

Use a commercially available cloth for cleaning glasses to gently wipe the lens.

Warning

Do not use sprays that contain flammable gas to remove dirt and dust from the lens. The projector may catch fire because of the high temperature of the lamp inside the projector.

Cleaning a •

If a message is frequently displayed, even after cleaning, it is time to replace the air filter. Replace it with a new air filter.

s

"Replacing the Air Filter" p.99

•

It is recommended that you clean these parts at least once every three months. Clean them more often than this if using the projector in a particularly dusty environment.

95

Replacing Consumables

96

This section explains how to replace the lamp and the air filter.

Replacing the Lamp

Lamp replacement period

It is time to replace the lamp when:

•

The following message is displayed.

"It is time to replace your lamp. Please contact your Epson projector reseller or visit www.epson.com to purchase."

The message is displayed for 30 seconds.

•

The lamp indicator flashes orange.

Attention

•

The lamp replacement message is set to appear after the following time periods in order to maintain the initial brightness and quality of the projected images.

EB-435W/EB-430

When Power Consumption is set to Normal : About 3900 hours

When Power Consumption is set to ECO : About 5900 hours

EB-425W/EB-420

When Power Consumption is set to Normal : About 4900 hours

When Power Consumption is set to ECO : About 5900 hours s Settings - Power Consumption

p.63

•

If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may blow increases. When the lamp replacement message is displayed, replace the lamp with a new one as soon as possible, even if it is still working.

•

Do not repeatedly turn off the power and immediately back on. Turning the power on and off frequently may shorten the lamp's operating life.

•

Depending on the individual characteristics of the lamp and the way it has been used, the lamp may become darker or stop working before the message is displayed. You should always have a spare lamp unit ready in case it is needed.

How to replace the lamp

The lamp can be replaced even when the projector is suspended from a wall or ceiling.

•

The projected image gets darker or starts to deteriorate.


Warning

•

When replacing the lamp because it has stopped working, there is a possibility that the lamp may be cracked.When replacing the lamp of a projector that has been installed on a wall or ceiling, assume that the lamp is cracked and stand to the side of the lamp cover, not underneath it. Also, remove the lamp cover gently.

• Never disassemble or modify a lamp. If a modified or disassembled lamp is installed in the projector and used, it could cause a fire, electric shock, or an accident.

Caution

Wait until the lamp has cooled down sufficiently before removing the lamp cover. If the lamp is still hot, burns or other injuries may result. It takes approximately one hour after the power has been turned off for the lamp to sufficiently cool down.

a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cable.

b Wait until the lamp has sufficiently cooled down, and then remove the lamp cover at the top of the projector.

Loosen the lamp cover fixing screw with the screwdriver supplied with the new lamp unit or a Phillips (+) screwdriver. Then slide the lamp cover straight forward and lift to remove it.

c Loosen the two lamp fixing screws.

97


98 d Remove the old lamp by pulling the handle.

If the lamp is cracked, replace it with a new lamp, or contact your local dealer for further advice.

s Epson Projector Contact List e Install the new lamp.

Insert the new lamp along the guide rail in the correct direction so that it fits in place, push in firmly, and once it is fully inserted tighten the two screws.

Replacing Consumables f Attach the lamp cover.

99

Attention

•

Make sure you install the lamp securely. If the lamp cover is removed, the power turns off automatically as a safety precaution. If the lamp or the lamp cover is not installed correctly, the power does not turn on.

•

This product includes a lamp component that contains mercury (Hg). Please consult your local regulations regarding disposal or recycling. Do not dispose of it with normal waste.

Resetting the lamp hours

The projector records how long the lamp is on and a message and indicator notify you when it is time to replace the lamp. After replacing the lamp, make sure you reset the lamp hours from the Configuration menu.

s

"Reset Menu" p.75

a

Only reset the lamp hours after the lamp has been replaced. Otherwise, the lamp replacement period will not be indicated correctly.

Replacing the Air Filter

Air filter replacement period

If the message is displayed frequently even though the air filter has been cleaned, replace the air filter.

How to replace the air filter

The air filter can be replaced even when the projector is suspended from a wall or ceiling.

Replacing Consumables a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cable.

b Open the air filter cover.

Press the tabs on the air filter cover and open the cover.

d Install the new air filter.

c Remove the air filter.

Grip the tab in the center of the air filter, and pull the air filter straight out.

e Close the air filter cover.

100

Replacing Consumables a

Dispose of used air filters properly in accordance with your local regulations.

Material of the frame part: Polypropylene

Material of the filter part: Polypropylene

101

Appendix

Slideshow

103

Projecting Without a Computer (Slideshow)

By connecting a USB storage device such as a USB memory or a USB hard disk to the projector, you can project the files stored on the device without using a computer. This function is called Slideshow.

a • You may not be able to use USB storage devices that incorporate security functions.

•

You cannot correct keystone distortion while projecting a Slideshow, even if you press the [ ] and [ ] buttons on the control panel.

a •

When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.

•

The projector does not support some file systems, so use media that has been formatted in Windows.

•

Format the media in FAT16/32.

Slideshow examples

Projecting images stored on USB storage

Specifications for files that can be projected using Slideshow

Type Notes

Image

File Type (Extension)

.jpg

.bmp

.gif

.png

The following cannot be projected.

- CMYK color mode format

- Progressive format

- Images with a resolution greater than 8192x8192

Due to the characteristics of JPEG files, images may not be projected clearly if the compression ratio is too high.

Cannot project images with a resolution greater than 1280x800.

•


•

Cannot project animated GIFs.


s

"Projecting the selected image" p.105

s

"Projecting image files in a folder in sequence (Slideshow)" p.106

Slideshow operating methods

Although the following steps are explained based on the remote control, you can perform the same operations from the control panel.

Starting Slideshow a Change the source to USB.

s

"Switching to the Target Image Using the Remote Control" p.30

Slideshow b Connect the USB storage device or digital camera to the projector.

s

"Connecting USB Devices" p.22

Slideshow starts and the file list screen is displayed.

•

JPEG files are displayed as thumbnails (file contents are displayed as small images).

•

Other files or folders are displayed as icons as shown in the following table.

Icon File

JPEG files *

Icon File

BMP files

GIF files PNG files

* When it cannot be displayed as a thumbnail, it is displayed as an icon.

104 a •

You can also insert a memory card into a USB card reader and then connect the reader to the projector. However, some commercially available USB card readers may not be compatible with the projector.

•

If the following screen (Select Drive screen) is displayed, press the

[ ], [ ], [ ], and [ ] buttons to select the drive you want to use, and then press the [ ] button.

• To display the Select Drive screen, position the cursor on Select

Drive at the top of the file list screen, and then press the [ ] button.

Projecting images a Use the [ ], [ ], [ ], and [ ] buttons to select the file or folder you want to project.

Slideshow b While projecting, press the [ ] or [ ] button.

105 a

If not all of the files and folders are displayed on the current screen, press the [ ] ] button on the remote control, or position the cursor on Next Page at the bottom of the screen and press the [ ] button.

To return to the previous screen, press the [ [ ] button on the remote control, or position the cursor on Previous Page at the top of the screen and press the [ ] button.

Stopping Slideshow

To close Slideshow, disconnect the USB device from the USB port on the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from the projector.

b Press the [ ] button.

The selected image is displayed.

When a folder is selected, the files in the selected folder are displayed. To return to the previous screen, position the cursor on

Back to Top and press the [ ] button.

Rotating images

You can rotate the played images in 90˚ increments. The rotating function is also available during Slideshow.

a Play images, or run Slideshow.

Projecting the selected image

Attention

Do not disconnect the USB storage device while it is being accessed.

Slideshow may not operate correctly.

a Start Slideshow.

The file list screen is displayed.

s

"Starting Slideshow" p.103

Slideshow

106 b Press the [ ], [ ], [ ], and [ ] buttons to select the image file you want to project.

Projecting image files in a folder in sequence (Slideshow)

You can project the image files in a folder in sequence, one at a time. This function is called Slideshow. Use the following procedure to run

Slideshow.

a

To change files automatically when you run Slideshow, set Screen

Switching Time from Option in Slideshow to anything other than No .

The default setting is 3 seconds.

c Press the [ ] button.

The image is displayed.

a

Press the [ ][ ] buttons to move to the next or previous image file.

d Press the [Esc] button to return to the file list screen.

a Start Slideshow.

The file list screen is displayed.

s

"Starting Slideshow" p.103

b Use the [ ], [ ], [ ], and [ ] buttons to position the cursor over the folder for the Slideshow that you want to run, and then press the [ ] button.

c Select Slideshow at the bottom right of the file list screen, and then press the [ ] button.

Slideshow starts, and the image files in the folder are automatically projected in sequence, one at a time.

When the last file is projected, the file list is displayed again automatically. If you set Continuous Play to On in the Option window, projection starts again from the beginning when it reaches the end.

s

"Image file display settings and Slideshow operation settings" p.107

You can proceed to the next screen, return to the previous screen, or stop playback while projecting a Slideshow.

Slideshow

107 a

If Screen Switching Time on the Option screen is set to No , files do not change automatically when you select Play Slideshow. Press the

[ ] button, the [ ] button, or the [ ] ] button to continue to the next file.

You can use the following functions when projecting an image file with

Slideshow.

•

Freeze s


• A/V Mute s


•

E-Zoom s


Image file display settings and Slideshow operation settings

You can set the file display order and Slideshow operations on the Option screen.

a Press the [ ], [ ], [ ] and [ ] buttons to position the cursor over the folder where you want to set display conditions, and then press the [Esc] button. Select Option from the submenu displayed, then press the [ ] button.

b When the following Option screen is displayed, set each of the items.

Enable settings by positioning the cursor on the target item and pressing the [ ] button.

The following table shows the details for each item.

Display Order You can select to display the files in Name Order or Date

Order .

Sort Order

Continuous

Play

You can select to sort the files In Ascending or In

Descending order.

You can set whether to repeat the Slideshow.

Screen Switching Time

Effect

You can set the time for a single file to be displayed in Play

Slideshow. You can set a time between No (0) to 60

Seconds. When you set No , auto play is disabled.

You can set the screen effects when changing slides.

c When you have finished making settings, use the [ ], [ ], [ ], and [ ] buttons to position the cursor over OK , and then press the [ ] button.

The settings are applied.

If you do not want to apply the settings, position the cursor on

Cancel , and then press the [ ] button.

Monitoring and Controlling

108

About EasyMP Monitor

EasyMP Monitor lets you carry out operations such as checking the status of multiple Epson projectors that are connected to a network at a computer monitor, and controlling the projectors from the computer.

You can download EasyMP Monitor from the following Web site.

http://www.epson.com

The following provides brief descriptions of the monitoring and control functions that can be carried out using EasyMP Monitor.

•

Registering projectors for monitoring and control

Projectors on the network can be searched for automatically, and you can then select which projectors you want to register from the projectors that are detected.

You can register target projectors by entering their IP addresses.

•

Registered projectors can also be assigned to groups so that they can be monitored and controlled in groups.

•

Monitoring the status of registered projectors

You can check the power status (ON/OFF) for projectors and problems or warnings that require attention by using the icons.

You can select groups of projectors or a single projector and then check the cumulative lamp operating time or information such as input sources, problems, and warnings for the projectors.

•

Controlling registered projectors

Projectors can be selected in groups or as single projectors, and you can then carry out operations for the selected projectors such as turning the power on and off and switching their input sources.

You can use Web Control functions to change the settings in the projector's configuration menu.

If there are certain control actions which are carried out regularly at particular times or on particular days, you can use Timer Settings to register timer settings.

•

Mail Notification settings

You can set e-mail addresses to which notifications are sent if a status that requires attention, such as a problem, occurs with a registered projector.

•

Sending messages to registered projectors

You can use the Message Broadcasting plugin for EasyMP Monitor to send JPEG files to registered projectors.

Download the Message Broadcasting plugin from the Web site address provided at the beginning of this chapter.

Changing Settings Using a Web Browser (Web

Control)

By using the Web browser of a computer connected to the projector on a network, you can set the projector's functions and control the projector.

This function allows you to perform setup and control operations remotely.

In addition, since you can use the computer's keyboard, entering characters required for the setup is easier.

Use Microsoft Internet Explorer 6.0 or later as the Web browser. If using a

Mac OS, use Safari or Firefox.

a

If you set Standby Mode to Communication On , you can use a Web browser to make settings and perform control even if the projector is in standby mode (when the power is off).


p.64

Projector setup

In a Web browser, you can set items that are usually set in the projector's

Configuration menu. The settings are reflected in the Configuration menu.

There are also items that can only be set in a Web browser.


109

Items in the Configuration menu that cannot be set by a Web browser

•

Settings menu - Keystone - Quick Corner

•

Settings menu - Pointer Shape

•

Settings menu - Pattern

•

Settings menu - User Button

•

Extended menu - User's Logo

•

Extended menu - Language

•

Extended menu - Operation - High Altitude Mode

•

Reset menu - Reset All and Reset Lamp Hours

The settings for items on each menu are the same as the projector's

Configuration menu.

s

"Configuration Menu" p.56

Items that can only be set with a Web browser

•

SNMP Community Name

•

Monitor Password

Displaying the Web Control screen

Use the following procedure to display the Web Control screen.

Make sure the computer and projector are connected to the network. Use

Advanced when connecting via a Wireless LAN.

a

If your Web browser is set up to connect via a proxy server, the Web

Control screen cannot be displayed. To display Web Control, you need to make settings so that a proxy server is not used for a connection.

a Start a Web browser on the computer.

b Enter the IP address of the projector in the address input box of the Web browser, and press the Enter key on the computer's keyboard.

The Web Control screen is displayed.

When Web Control Password is set in the Network menu from the projector's Configuration menu, the password entry screen is displayed.

Displaying the Web Remote screen

The Web Remote function allows you to perform projector remote control operations with a Web browser.

a b

Display the Web Control screen.

Click Web Remote .

c The Web Remote screen is displayed.


110

Name

F [Page] buttons

[Up] [Down]

G [Source Search] button

Name

A [ t ] button

B [Computer] button

C

D

E

[Video] button

[Freeze] button

[A/V Mute] button

Function


s


Each time you press the button, the input changes between images from the Computer1 port and the Computer2 port.

Each time the button is pressed, the image cycles through

Video, S-Video, and HDMI ports.


s



s


Mute)" p.44

H [LAN] button

I [USB] button

J [Volume] buttons

[ a ][ b ]

Function

Changes pages in files such as PowerPoint files when using the following projection methods.

•

When using the Wireless Mouse function s



•

When using USB Display s


•

When connecting to a network

When projecting images using Slideshow, pressing these buttons displays the previous/next image file.


s



Changes to the images projected with EasyMP Network

Projection. When projecting using the optional Quick

Wireless Connection USB Key, this button switches to that image.

s

"Switching to the Target Image Using the Remote

Control" p.30

Each time the button is pressed, it cycles through the following images:

•

USB Display

•

Images from the device connected to the USB(TypeA) port s

"Switching to the Target Image Using the Remote

Control" p.30

[ a ] Decreases the volume.

[ b ] Increases the volume.

s



111

Using the Mail Notification Function to Report

Problems

When you set Mail Notification, notification messages are sent to the preset email addresses when a problem or warning occurs with a projector. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.

s Network - Mail - Mail Notification

p.72

a •

Up to a maximum of three notification destinations (addresses) can be registered, and notification messages can be sent to all three destinations at once.

• If a projector develops a critical problem and suddenly stops working, it may not be able to send a message notifying an operator of the problem.

• Controlling is possible if Standby Mode is set to Communication

On , even if the projector is in standby state (when the power is off).


p.64

•

Internal error

•

Fan related error

•

Sensor error

•

Lamp timer failure

•

Lamp out

•

Internal temperature error

•

High-speed cooling in progress

•

Lamp replacement notification

•

No-signal

No Signal is input to the projector. Check the connection status or check that the power for the signal source is turned on.

•

Auto Iris Error

•

Power Err. (Ballast)

See the following to deal with problems or warnings.

s

"Reading the Indicators" p.79

Reading Error Notification Mail

When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent.

Subject: EPSON Projector

Line 1: The name of the projector where the problem occurred

Line 2: The IP address set for the projector where the problem has occurred.

Line 3 and on: Details of the problem

The details of the problem are listed line by line. The main message contents are listed below.

Management Using SNMP

By setting SNMP to On in the Configuration menu, notification messages are sent to the specified computer when a problem or warning occurs. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.

s

Network - Others - SNMP

p.73


112 a •

SNMP should be managed by a network administrator or someone who is familiar with the network.

•

To use the SNMP function to monitor the projector, you need to install the SNMP manager program on your computer.

•

The managing function using SNMP cannot be used via wireless

LAN in Quick connection mode.

•

Up to two destination IP addresses can be saved.

ESC/VP21 Commands

You can control the projector from an external device using ESC/VP21.

Item

HDMI

Video

S-Video

USB Display

USB

LAN

A/V Mute ON/OFF On

Off

RGB

Component

Command

SOURCE 21

SOURCE 24

SOURCE 30

SOURCE 41

SOURCE 42

SOURCE 51

SOURCE 52

SOURCE 53

MUTE ON

MUTE OFF

Add a Carriage Return (CR) code (0Dh) to the end of each command and transmit.

For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Command list

When the power ON command is transmitted to the projector, the power turns on and it enters warm-up mode. When the projector's power has turned on, a colon ":" (3Ah) is returned.

When a command is input, the projector executes the command and returns a ":", and then accepts the next command.

If the command being processed terminates abnormally, an error message is output and a ":" is returned.

The main contents are listed below.

Power ON/OFF

Signal selection

Item

On

Off

Computer1

Computer2

Auto

RGB

Component

Auto

Command

PWR ON

PWR OFF

SOURCE 1F

SOURCE 11

SOURCE 14

SOURCE 2F

Cable layouts

Serial connection

•

Connector shape: D-Sub 9-pin (male)


•

Projector input port name: RS-232C

<At the projector>

<At the projector>

Signal Name

GND

TD

RD

Function

Signal wire ground

Transmit data

Receive data

Communications protocol

• Default baud rate setting: 9600 bps

• Data length: 8 bit

• Parity: None

•

Stop-bit: 1 bit

• Flow control: None

113

<At the computer>

(PC serial cable) <At the computer>

About PJLink

PJLink Class1 was established by the JBMIA (Japan Business Machine and

Information System Industries Association) as a standard protocol for controlling network-compatible projector's as part of their efforts to standardize projector control protocols.

The projector complies with the PJLink Class1 standard established by the

JBMIA.

See the following for more information on network settings related to

PJLink.

s

"Network Menu" p.66

It complies with all commands except for the following commands defined by PJLink Class1, and agreement was confirmed by the PJLink standard adaptability verification.

URL: http://pjlink.jbmia.or.jp/english/

•

Non-compatible commands

Mute settings

Function

Image muting set

Audio muting set

PJLink Command

AVMT 11

AVMT 21

•

Input names defined by PJLink and corresponding projector sources

Source PJLink Command

Computer1

Computer2

Video

S-Video

HDMI

USB

INPT 11

INPT 12

INPT 21

INPT 22

INPT 32

INPT 41


114

LAN

USB Display

Source

INPT 52

INPT 53

PJLink Command

• Manufacturer name displayed for "Manufacture name information query"

EPSON

•

Model name displayed for "Product name information query"

EB-420/CS500XN/PowerLite 420

EB-425W/CS500WN/PowerLite 425W

EB-435W/CS520WN/PowerLite 435W

EB-430/CS510XN/PowerLite 430

•

Monitoring and control with application software

You can use Crestron RoomView ® Express or Crestron RoomView ®

Server Edition provided by Creston ® to monitor devices in the system, to communicate with the help desk, and to send emergency messages. See the following Web site for details.

http://www.crestron.com/getroomview

This manual describes how to perform operations on your computer using a Web browser.

a • You can only enter single-byte alphanumeric characters and symbols.

• The following functions cannot be used while using Crestron

RoomView ® .

s


Message Broadcasting (EasyMP Monitor plug-in)

• Controlling is possible if Standby Mode is set to Communication

On , even if the projector is in standby state (when the power is off).


p.64

About Crestron RoomView

®

Crestron RoomView ® is an integrated control system provided by

Crestron ® . It can be used to monitor and control multiple devices connected on a network.

The projector supports the control protocol, and can therefore be used in a system built with Crestron RoomView ® .

Visit the Crestron ® Web site for details on Crestron RoomView ® .

http://www.crestron.com

The following provides an overview of Crestron RoomView ® .

•

Remote operation using a Web browser

You can operate a projector from your computer just like using a remote control.

Operating a projector from your computer

Displaying the operation window

Check the following before carrying out any operations.

•

Make sure the computer and projector are connected to the network.

When communicating with a wireless LAN, connect in Advanced connection mode.

s

"Wireless LAN menu" p.68

•

Set Crestron RoomView to On from the Network menu.

s

Network - Others - Crestron RoomView

p.73

Monitoring and Controlling a b

Start a Web browser on the computer.

Enter the IP address of the projector in the address field of the

Web browser, and press the Enter key on the keyboard.

The operation window is displayed.

Using the operation window

A You can perform the following operations when you click the buttons.

Power

Button

Vol-/Vol+

Function


Adjusts the volume.

115

A/V Mute

Freeze

Button

Contrast

Button

Brightness

Color

Sharpness

Zoom

Function


s


Mute)" p.44

B Switch to the image from the selected input source. To display input sources that are not shown on the screen, click (a) or (b) to scroll up or down.

You can change the source name if necessary.

C You can perform the following operations when you click the buttons. To display buttons that are not shown on the screen, click (c) or (d) to scroll left or right.

Function


s


You can adjust the difference between light and dark in the images.

You can adjust the image brightness.

You can adjust the color saturation for the images.

You can adjust the image sharpness.

Click the [ z ] button to enlarge the image without changing the projection size. Click the [ x ] button to reduce an image that was enlarged with the [ z ] button.

Click the [ ], [ ], [ ], or [ ] button to change the position of an enlarged image.

s


D

[ ], [ ], [ ], or [ ] buttons have the same effects as [ ][ ][ ][ ] buttons on the remote control. You can perform the following operations when you click the other buttons.


OK

Menu

Auto

Search

Esc

Button Function

Performs the same operation as the [ ] button on the remote control.

s

"Remote Control" p.12

Displays and closes the Configuration menu.

If clicked while projecting analog RGB signals from

Computer1 port or Computer2 port, automatically optimizes the image by adjusting the Tracking, Sync., and Position.


s



Performs the same operation as the [Esc] button on the remote control.

s

"Remote Control" p.12

E You can perform the following operations when you click the tabs.

Tab

Contact IT Help

Info

Tools

Function

Displays the Help Desk window. Used to send messages to, and receive messages from, the administrator using

Crestron RoomView ® Express.

Displays information on the projector that is currently connected.

Changes settings in the projector that is currently connected. See the next section.

Using the tools window

The following window is displayed when you click the Tools tab on the operation window. You can use this window to change settings in the projector that is currently connected.

116

A Crestron Control

Make settings for Crestron ® central controllers.

B Projector

The following items can be set.

Item

Projector Name

Location

Assigned To

Function

Enter a name to differentiate the projector that is currently connected from other projectors on the network. (The name can contain up to 15 single-byte alphanumeric characters.)

Enter an installation location name for the projector that is currently connected on the network. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)

Enter a user name for the projector. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)


DHCP

Send

Item

IP Address

Subnet Mask

Default Gateway

Function

Select the Enabled check box to use DHCP. You cannot enter an IP address if DHCP is enabled.

Enter the IP address to assign to the currently connected projector.

Enter a subnet mask for the currently connected projector.

Enter the gateway address for the currently connected projector.

Click this button to confirm the changes made to the

Projector .

C Admin Password

Select the Enabled check box to require a password to open the Tools window.


Item

New Password

Confirm

Send

Function

Enter the new password when changing the password to open the Tools window. (The name can contain up to 26 single-byte alphanumeric characters.)

Enter the same password as you entered in New

Password . If the passwords are not the same, an error is displayed.


Admin Password .

D User Password

Select the Enabled check box to require a password to open the operation window on the computer.


Item

New Password

Confirm

Send

117

Function

Enter the new password when changing the password to open the operation window. (The name can contain up to 26 single-byte alphanumeric characters.)

Enter the same password as you entered in New

Password . If the passwords are not the same, an error is displayed.


User Password .

Optional Accessories and Consumables

118

The following optional accessories and consumables are available. Please purchase these products as and when needed.The following list of optional accessories and consumables is current as of: August 2011. Details of accessories are subject to change without notice.

Optional Accessories

Document Camera ELPDC06/ELPDC11

Use when projecting images such as books, OHP documents, or slides.

Computer cable ELPKC02

(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)

This is the same as the computer cable supplied with the projector.


(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)


(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)

These are extension cables for when the computer cable supplied with the projector is too short.

Component video cable ELPKC19

(3 m - for mini D-Sub 15-pin/RCA male ^ 3)

Use to connect a Component Video

g

source.

Wireless LAN unit ELPAP07

Use when connecting the projector to a computer wirelessly and projecting.

Quick Wireless Connection USB Key ELPAP08

Use when you want to quickly establish one-to-one connection between the projector and a computer with Windows installed.

Wall mount * ELPMB27

Use this arm type fitting when installing the projector on a wall.

Interactive Unit ELPIU03

Use when operating the computer screen on the projection surface.

Ceiling mount * ELPMB23

Use when installing the projector on a ceiling.

Ceiling pipe (450 mm) * ELPFP13

Ceiling pipe (700 mm) * ELPFP14

Use when installing the projector on a high ceiling.

* Special expertise is required to suspend the projector. Contact your local dealer or the nearest address provided in the Epson Projector Contact List.


Consumables

Lamp unit (for EB-425W/EB-420) ELPLP60

Lamp unit (for EB-435W/EB-430) ELPLP61

Use as a replacement for a used lamp.

Air filter ELPAF36

Use as a replacement for a used air filter.

Screen Size and Projection Distance

Projection Distance (For EB-430/EB-420)

A Projection distance

B Distance from the center of the lens to the base of the screen

(or to the top of the screen, if suspended from a wall or ceiling)

C Center of lens

119

4:3 Screen Size

50"

60"

70"

80"

90"

100"

108"

100x76

120x91

140x105

160x120

180x135

200x150

219x165

* Project using Wide (maximum zoom).

A

Minimum (Wide) to Maximum

(Tele)

55 - 75

66 - 90

78 - 106

89 - 122

101 *

112 *

122 *

Unit: cm

B

Minimum

(Wide)

6

8

9

10

12

13

14

16:9 Screen Size

50"

60"

70"

80"

90"

99"

110x62

130x75

150x87

180x100

200x110

219x123


A


(Tele)

60 - 82

72 - 99

85 - 116

98 *

110 *

121 *

Unit: cm

B

Minimum

(Wide)

17

21

24

28

31

34


Projection Distance (For EB-435W/EB-425W)

A Projection distance

B Distance from the center of the lens to the base of the screen

(or to the top of the screen, if suspended from a wall or ceiling)

C Center of lens

120

4:3 Screen Size

50"

60"

70"

80"

90"

102"

100x76

120x91

140x105

160x120

180x135

207x155


A


(Tele)

58 - 79

70 - 96

82 - 112

94 *

107 *

121 *

Unit: cm

B

Minimum

(Wide)

9

11

13

14

16

18

16:9 Screen Size

60"

70"

80"

90"

100"

113"

130x75

150x87

180x100

200x110

220x120

250x141


A


(Tele)

63 - 87

74 - 101

85 - 116

97 *

108 *

122 *

Unit: cm

B

Minimum

(Wide)

14

16

19

21

23

26

16:10 Screen Size

55"

60"

115x72

130x81

A


(Tele)

56 - 77

61 - 84

Unit: cm

B

Minimum

(Wide)

9

9


16:10 Screen Size

70"

80"

90"

100"

116"

150x94

170x110

190x120

220x130

251x157


A


(Tele)

72 - 99

83 - 113

94 *

105 *

122 *

B

Minimum

(Wide)

11

13

14

16

18

121

Supported Monitor Displays

Supported Resolutions

Computer signals (analog RGB)

Signal

VGA

SVGA

XGA

WXGA

WXGA+

SXGA

SXGA+

WSXGA+

UXGA

*

MAC13”

MAC16”

MAC19”

1, 2

Refresh Rate (Hz)

60/72/75/85

56/60/72/75/85

60/70/75/85

60

60

60/75/85

60/75/85

70/75/85

60/75/85

60/75/85

60/75

60

60

67

75

75

59

75

Resolution (dots)

640x480

800x600

1024x768

1280x768

1360x768

1280x800

1440x900

1152x864

1280x1024

1280x960

1400x1050

1680x1050

1600x1200

640x480

832x624

1024x768

1024x768

1152x870 MAC21”

* 1 EB-435W/EB-425W only

* 2 Only compatible when Wide is selected as the Resolution from the

Configuration menu.

Images may also be projected when signals other than the above are input.

However, some functions may be limited.

Component Video

Signal

SDTV (480i)

SDTV (576i)

SDTV (480p)

SDTV (576p)

HDTV (720p)

HDTV (1080i)

Composite video

Signal

TV (NTSC)

TV (SECAM)

TV (PAL)

Refresh Rate (Hz)

60

50

60

50

50/60

50/60

Refresh Rate (Hz)

60

50

50/60

Input signal from the HDMI port

Signal

VGA

SVGA

XGA

WXGA

SXGA

SXGA+

UXGA

Refresh Rate (Hz)

60

60

60

60

60

60

60

60

Resolution (dots)

720x480

720x576

720x480

720x576

1280x720

1920x1080

Resolution (dots)

720x480

720x576

720x576

Resolution (dots)

640x480

800x600

1024x768

1280x800

1280x960

1280x1024

1400x1050

1600x1200

122

Supported Monitor Displays

Signal

SDTV (480i/480p)

SDTV (576i/576p)

HDTV (720p)

HDTV (1080i)

HDTV (1080p)

Refresh Rate (Hz)

60

50

50/60

50/60

24/30/50/60

Resolution (dots)

720x480

720x576

1280x720

1920x1080

1920x1080

123

Specifications

Projector General Specifications

Product name

Dimensions

LCD panel size

Display method

Resolution

Focus adjustment

Zoom adjustment

Lamp

Max. audio output

Speaker

Power supply

Power consumption

100 to 120 V area

220 to 240 V area

Operating altitude

Operating temperature

Storage temperature

Mass

EB-435W

0.59" Wide

EB-430 EB-425W

345 (W) x 105 (H) x 277 (D) mm (not including raised section)

0.55" 0.59" Wide

EB-420

0.55"

1,024,000

WXGA (1280 (W)x 800 (H) dots)x 3

Polysilicon TFT active matrix

786,432

XGA (1024 (W) x 768 (H) dots)x 3

Manual

1,024,000

WXGA (1280 (W)x 800 (H) dots)x 3

Digital (1-1.35)

UHE lamp, 230 W Model No.: ELPLP61

786,432

XGA (1024 (W) x 768 (H) dots)x 3

UHE lamp, 200 W Model No.: ELPLP60

16 W

1

100 to 240V AC ±10%, 50/60 Hz 3.4 to 1.5 A

Operating: 332 W

Standby power consumption (Communication On): 6.8 W

Standby power consumption (Communication Off): 0.28 W

Operating: 316 W



Operating: 294 W



Operating: 283 W



Altitude 0 to 2,286 m

+5 to +35°C (No condensation)

Approx. 3.9 kg

100 to 240V AC ±10%, 50/60 Hz 3.0 to 1.3 A

-10 to +60°C (No condensation)

Approx. 3.9 kg Approx. 3.8 kg Approx. 3.8 kg

Connectors Computer1 port

Computer2 port

1

1

Mini D-Sub15-pin (female)


124

Specifications

Video port

S-Video port

Audio1 port

Audio2 port

Audio-L/R port

Mic port

Audio Out port

Monitor Out port

HDMI port

USB(TypeA) port *

USB(TypeB) port *

USB port

(dedicated Wireless LAN unit)

LAN port

RS-232C port

1

1

1

1

1

1

1

1

1

1

1

1

1

1

* Supports USB 2.0. However, the operation of all USB compatible devices is not guaranteed.

RCA pin jack

Mini DIN 4-pin

Stereo mini pin jack


RCA pin jack x 2 (L-R)




HDMI (Audio is only supported by PCM)

USB connector (Type A)

USB connector (Type B)

USB connector (Type A)

RJ-45

Mini D-Sub 9-pin (male)

125

Specifications

This product is also designed for IT power distribution system with phase-to-phase voltage 230V.

Angle of tilt

If you use the projector tilted at an angle of more than 15˚ it could be damaged and cause an accident.

126

Specifications

127

DECLARATION of CONFORMITY

According to 47CFR, Part 2 and 15

Class B Personal Computers and Peripherals; and/or

CPU Boards and Power Supplies used with Class B Personal Computers

We:

Located at:

Tel:

Epson America, Inc.

3840 Kilroy Airport Way

MS: 3-13

Long Beach, CA 90806

562-290-5254

Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Trade Name: EPSON

Type of Product:

Model:

LCD Projector

H447C/H448C/H449C/H469C

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

Appearance

A Center of lens

B Measurements from the center of the lens to the wall mount plate fixing points or the ceiling mount fixing points.

128

Units: mm

Glossary

129

This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.

AMX Device Discovery

Aspect Ratio

Component Video

Composite video

Contrast

DHCP

Gateway Address

HDCP

HDTV

Interlace

IP Address

Progressive

SDTV

SNMP

AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.

Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).

See the AMX Web site for more details.

URL http://www.amx.com/

The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.

SDTV and general computer displays have an aspect ratio of 4:3.

A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or

Pr).

A method that combines the video signal into a luminance component and a color component for transmission down a single cable.

The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called "contrast adjustment".

An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP address g

to equipment connected to a network.

This is a server (router) for communicating across a network (subnet) divided according to subnet mask

g .

HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by

HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.

An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.

• Vertical resolution of 720p or 1080i or greater (p = Progressive

•

Screen aspect ratio g

of 16:9

g , i = Interlace g )

Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.

Images are more likely to flicker because one frame is displayed every other line.

A number to identify a computer connected to a network.

Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount of flicker in images decreases because the volume of information has doubled compared with an interlace system.

An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV

g High-

Definition Television.

An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network.

Glossary sRGB

SSID

Subnet Mask

SVGA

S-Video

SXGA

Sync.

Tracking

Trap IP Address

VGA

XGA

130

An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source to sRGB.

SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices that correspond to SSID.

This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.

A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.

A method that separates the video signal into a luminance component (Y) and a color component (C).

A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.

The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called

Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.

The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If tracking is not carried out correctly, wide vertical stripes appear in the signal.

This is the IP address g

for the destination computer used for error notification in SNMP.

A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.

A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.

General Notes

131

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko

Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the

U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as

Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

The contents of this guide may be changed or updated without further notice.

Illustrations in this guide and the actual projector may differ.

About Notations

Microsoft ® Windows ® 98 operating system

Microsoft ® Windows ® Me operating system


Microsoft ® Windows ® XP Professional operating system

Microsoft ® Windows ® XP Home Edition operating system

Microsoft ® Windows Vista ® operating system


In this guide, the operating systems above are referred to as "Windows 98",

"Windows Me", "Windows 2000", "Windows XP", "Windows Vista", and

"Windows 7". Furthermore, the collective term Windows may be used to refer to Windows 98, Windows Me, Windows 2000, Windows XP,

Windows Vista, and Windows 7, and multiple versions of Windows may be referred to as, for example, Windows 98/Me/2000/XP/Vista, with the

Windows notation omitted.

Mac OS X 10.3.x

Mac OS X 10.4.x

Mac OS X 10.5.x

Mac OS X 10.6.x

In this guide, the operating systems above are referred to as "Mac OS X

10.3.9", "Mac OS X 10.4.x", "Mac OS X 10.5.x", and "Mac OS X 10.6.x".

Furthermore, the collective term "Mac OS" is used to refer to them.

General Notice:

IBM, DOS/V, and XGA are trademarks or registered trademarks of International

Business Machines Corp.

Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.

Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

WPA ™ and WPA2 ™ are registered trademarks of Wi-Fi Alliance.

HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.

PJLink trademark is a trademark applied for registration or is already registered in

Japan, the United States of America and other countries and areas.

Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

©SEIKO EPSON CORPORATION 2011. All rights reserved.

Index

132

A

A/V Mute ...................................................... 44

Abs. Color Temp. ........................................ 60

Air exhaust vent ............................................. 8

Air filter replacement period ..................... 99

Aspect ...................................................... 40, 62

Auto Iris .................................................. 39, 61

Auto Setup .................................................... 61

B

Basic menu .................................................... 68

Blackboard .................................................... 39

Brightness ..................................................... 60

C

Ceiling ..................................................... 17, 65

Ceiling mount fixing points ....................... 10

Cleaning ........................................................ 94

Cleaning the air filter and air intake vent

.......................................................................... 94

Cleaning the projector's surface ................ 94

Color Adjustment ........................................ 61

Color Mode ............................................ 38, 60

Color Saturation .......................................... 60

Computer port ............................................... 9

Configuration menu .................................... 57

Connection mode ........................................ 69

Consumables .............................................. 118

Continuous ................................................. 107

Contrast ........................................................ 60

Control panel ............................................... 11

Control Panel Lock ............................... 54, 63

Crestron RoomView ................................. 114

Cross .............................................................. 46

D

Direct Power On .......................................... 65

Display ........................................................... 65

Display Background .................................... 65

Display Order ............................................. 107

Display settings .......................................... 107

Distance ...................................................... 119

Document Camera .................................... 118

Dynamic ........................................................ 38

E

EasyMP Monitor ....................................... 108

Email address ............................................... 73

ESC/VP21 ................................................... 112

Extended menu ............................................ 64

E-Zoom ......................................................... 46

F

Focus ring ....................................................... 8

Foot adjust lever ............................................. 8

Freeze ............................................................. 44

Front ........................................................ 17, 65

Front adjustable foot ..................................... 8

Full Lock ....................................................... 54

G

Gateway Address ................................... 69, 72

I

H

H/V-Keystone .............................................. 34

HDMI port ...................................................... 9

HDMI Video Range .................................... 62

Help function ............................................... 78

High Altitude Mode .................................... 65

How to replace the air filter ........................ 99

How to replace the lamp ............................. 96

Image menu .................................................. 60

Indicators ...................................................... 79

Info menu ..................................................... 74

Input Signal ............................................ 62, 75

IP Address ..................................................... 72

K

Keystone ........................................................ 63

L

Lamp cover ..................................................... 8

Lamp Hours .................................................. 75

Lamp indicator ............................................. 79

Lamp replacement period .......................... 96

Language ....................................................... 66

M

Mail Notification ................................. 72, 111

Mail Notification menu .............................. 72

Message Broadcasting ............................... 108

Messages ....................................................... 65

Mic Input Level ............................................ 63

Index

133

N

Network Configuration .............................. 66

Network information .................................. 66

Network menu ............................................. 66

Noise Reduction ........................................... 62

O

Monitor displays ........................................ 122

Mouse pointer .............................................. 47

Operating temperature ............................. 124

Operation ...................................................... 65

Optional accessories .................................. 118

Overheating .................................................. 80

P

Part names and functions ............................. 8

Password protect .......................................... 52

Password protect sticker ............................. 53

Pattern ........................................................... 64

Photo ............................................................. 38

PJLink .......................................................... 113

PJLink Password .......................................... 68

Pointer ........................................................... 45

Pointer Shape ............................................... 63

Port Number ................................................ 72

Position ......................................................... 62

Power Consumption ................................... 63

Power indicator ............................................ 79

Power inlet ...................................................... 9

Power On Protect ........................................ 52

Presentation ......................................... 38, 103

Problem solving ........................................... 79

Q

Quick Corner ............................................... 63

R

Progressive .................................................... 62

Projection ...................................................... 65

Projector Keyword ....................................... 68

Projector Name ............................................ 68

Projector setup ........................................... 108

Reading mail ............................................... 111

Rear .......................................................... 17, 65

Rear feet ........................................................ 11

Rear screen .................................................... 17

Refresh Rate .................................................. 75

Remote control ............................................ 12

Remote receiver ............................................. 8

Replacing batteries ....................................... 15

Reset All ........................................................ 75

Reset Lamp Hours ....................................... 76

Reset menu ............................................. 74, 75

Resetting the lamp operating time ............ 99

Resolution ..................................................... 75

Rotating images ......................................... 105

S

Screen size ................................................... 119

Screen switching time ............................... 107

Security menu .............................................. 70

Select Drive ................................................. 104

Settings menu ............................................... 63

Sharpness ...................................................... 60

Signal menu .................................................. 61

Sleep Mode ................................................... 65

Slideshow ............................................ 103, 106

SMTP Server ................................................. 72

SNMP .......................................................... 111

Soft keyboard ................................................ 67

Source ............................................................ 75

Source Search ......................................... 11, 29

Specifications ............................................. 124

Sports ............................................................. 38 sRGB .............................................................. 38

SSID ............................................................... 69

Standby Microphone ................................... 65

Standby Mode .............................................. 65

Startup Screen .............................................. 65

Storage temperature .................................. 124

Subnet Mask ........................................... 69, 72

Supported monitor displays ..................... 122

S-Video port ................................................. 10

Sync Info ....................................................... 75

Sync. ............................................................... 62

T

Temp indicator ............................................ 79

Theatre .......................................................... 38

Tint ................................................................ 60

Tracking ........................................................ 61

U

USB(TypeA) port ........................................... 9

USB(TypeB) port ........................................... 9

User Button .................................................. 64

User Pattern .................................................. 50

User's Logo ................................................... 48

Index

User's Logo Protect ...................................... 52

V

W

Web browser .............................................. 108

Web Control ............................................... 109

Web Control Password ............................... 68

Web Remote ............................................... 109

Whiteboard ................................................... 39

Wired LAN menu ........................................ 71

Wireless LAN menu .................................... 68

Wireless LAN Power ................................... 68

Wireless LAN system .................................. 69

Wireless mouse function ............................ 47

Z

Video port ....................................................... 9

Video Signal ........................................... 62, 75

Volume .......................................................... 63

Zoom ............................................................. 63

134

No results