advertisement
Appendix
Slideshow
103
Projecting Without a Computer (Slideshow)
By connecting a USB storage device such as a USB memory or a USB hard disk to the projector, you can project the files stored on the device without using a computer. This function is called Slideshow.
a • You may not be able to use USB storage devices that incorporate security functions.
•
You cannot correct keystone distortion while projecting a Slideshow, even if you press the [ ] and [ ] buttons on the control panel.
a •
When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
•
The projector does not support some file systems, so use media that has been formatted in Windows.
•
Format the media in FAT16/32.
Slideshow examples
Projecting images stored on USB storage
Specifications for files that can be projected using Slideshow
Type Notes
Image
File Type (Extension)
.jpg
.bmp
.gif
.png
The following cannot be projected.
- CMYK color mode format
- Progressive format
- Images with a resolution greater than 8192x8192
Due to the characteristics of JPEG files, images may not be projected clearly if the compression ratio is too high.
Cannot project images with a resolution greater than 1280x800.
•
Cannot project images with a resolution greater than 1280x800.
•
Cannot project animated GIFs.
Cannot project images with a resolution greater than 1280x800.
s
"Projecting the selected image" p.105
s
"Projecting image files in a folder in sequence (Slideshow)" p.106
Slideshow operating methods
Although the following steps are explained based on the remote control, you can perform the same operations from the control panel.
Starting Slideshow a Change the source to USB.
s
"Switching to the Target Image Using the Remote Control" p.30
Slideshow b Connect the USB storage device or digital camera to the projector.
s
Slideshow starts and the file list screen is displayed.
•
JPEG files are displayed as thumbnails (file contents are displayed as small images).
•
Other files or folders are displayed as icons as shown in the following table.
Icon File
JPEG files *
Icon File
BMP files
GIF files PNG files
* When it cannot be displayed as a thumbnail, it is displayed as an icon.
104 a •
You can also insert a memory card into a USB card reader and then connect the reader to the projector. However, some commercially available USB card readers may not be compatible with the projector.
•
If the following screen (Select Drive screen) is displayed, press the
[ ], [ ], [ ], and [ ] buttons to select the drive you want to use, and then press the [ ] button.
• To display the Select Drive screen, position the cursor on Select
Drive at the top of the file list screen, and then press the [ ] button.
Projecting images a Use the [ ], [ ], [ ], and [ ] buttons to select the file or folder you want to project.
Slideshow b While projecting, press the [ ] or [ ] button.
105 a
If not all of the files and folders are displayed on the current screen, press the [ ] ] button on the remote control, or position the cursor on Next Page at the bottom of the screen and press the [ ] button.
To return to the previous screen, press the [ [ ] button on the remote control, or position the cursor on Previous Page at the top of the screen and press the [ ] button.
Stopping Slideshow
To close Slideshow, disconnect the USB device from the USB port on the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from the projector.
b Press the [ ] button.
The selected image is displayed.
When a folder is selected, the files in the selected folder are displayed. To return to the previous screen, position the cursor on
Back to Top and press the [ ] button.
Rotating images
You can rotate the played images in 90˚ increments. The rotating function is also available during Slideshow.
a Play images, or run Slideshow.
Projecting the selected image
Attention
Do not disconnect the USB storage device while it is being accessed.
Slideshow may not operate correctly.
a Start Slideshow.
The file list screen is displayed.
s
Slideshow
106 b Press the [ ], [ ], [ ], and [ ] buttons to select the image file you want to project.
Projecting image files in a folder in sequence (Slideshow)
You can project the image files in a folder in sequence, one at a time. This function is called Slideshow. Use the following procedure to run
Slideshow.
a
To change files automatically when you run Slideshow, set Screen
Switching Time from Option in Slideshow to anything other than No .
The default setting is 3 seconds.
c Press the [ ] button.
The image is displayed.
a
Press the [ ][ ] buttons to move to the next or previous image file.
d Press the [Esc] button to return to the file list screen.
a Start Slideshow.
The file list screen is displayed.
s
b Use the [ ], [ ], [ ], and [ ] buttons to position the cursor over the folder for the Slideshow that you want to run, and then press the [ ] button.
c Select Slideshow at the bottom right of the file list screen, and then press the [ ] button.
Slideshow starts, and the image files in the folder are automatically projected in sequence, one at a time.
When the last file is projected, the file list is displayed again automatically. If you set Continuous Play to On in the Option window, projection starts again from the beginning when it reaches the end.
s
"Image file display settings and Slideshow operation settings" p.107
You can proceed to the next screen, return to the previous screen, or stop playback while projecting a Slideshow.
Slideshow
107 a
If Screen Switching Time on the Option screen is set to No , files do not change automatically when you select Play Slideshow. Press the
[ ] button, the [ ] button, or the [ ] ] button to continue to the next file.
You can use the following functions when projecting an image file with
Slideshow.
•
Freeze s
"Freezing the Image (Freeze)" p.44
• A/V Mute s
"Hiding the Image and Sound Temporarily (A/V Mute)" p.44
•
E-Zoom s
"Enlarging Part of the Image (E-Zoom)" p.46
Image file display settings and Slideshow operation settings
You can set the file display order and Slideshow operations on the Option screen.
a Press the [ ], [ ], [ ] and [ ] buttons to position the cursor over the folder where you want to set display conditions, and then press the [Esc] button. Select Option from the submenu displayed, then press the [ ] button.
b When the following Option screen is displayed, set each of the items.
Enable settings by positioning the cursor on the target item and pressing the [ ] button.
The following table shows the details for each item.
Display Order You can select to display the files in Name Order or Date
Order .
Sort Order
Continuous
Play
You can select to sort the files In Ascending or In
Descending order.
You can set whether to repeat the Slideshow.
Screen Switching Time
Effect
You can set the time for a single file to be displayed in Play
Slideshow. You can set a time between No (0) to 60
Seconds. When you set No , auto play is disabled.
You can set the screen effects when changing slides.
c When you have finished making settings, use the [ ], [ ], [ ], and [ ] buttons to position the cursor over OK , and then press the [ ] button.
The settings are applied.
If you do not want to apply the settings, position the cursor on
Cancel , and then press the [ ] button.
Monitoring and Controlling
108
About EasyMP Monitor
EasyMP Monitor lets you carry out operations such as checking the status of multiple Epson projectors that are connected to a network at a computer monitor, and controlling the projectors from the computer.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
The following provides brief descriptions of the monitoring and control functions that can be carried out using EasyMP Monitor.
•
Registering projectors for monitoring and control
Projectors on the network can be searched for automatically, and you can then select which projectors you want to register from the projectors that are detected.
You can register target projectors by entering their IP addresses.
•
Registered projectors can also be assigned to groups so that they can be monitored and controlled in groups.
•
Monitoring the status of registered projectors
You can check the power status (ON/OFF) for projectors and problems or warnings that require attention by using the icons.
You can select groups of projectors or a single projector and then check the cumulative lamp operating time or information such as input sources, problems, and warnings for the projectors.
•
Controlling registered projectors
Projectors can be selected in groups or as single projectors, and you can then carry out operations for the selected projectors such as turning the power on and off and switching their input sources.
You can use Web Control functions to change the settings in the projector's configuration menu.
If there are certain control actions which are carried out regularly at particular times or on particular days, you can use Timer Settings to register timer settings.
•
Mail Notification settings
You can set e-mail addresses to which notifications are sent if a status that requires attention, such as a problem, occurs with a registered projector.
•
Sending messages to registered projectors
You can use the Message Broadcasting plugin for EasyMP Monitor to send JPEG files to registered projectors.
Download the Message Broadcasting plugin from the Web site address provided at the beginning of this chapter.
Changing Settings Using a Web Browser (Web
Control)
By using the Web browser of a computer connected to the projector on a network, you can set the projector's functions and control the projector.
This function allows you to perform setup and control operations remotely.
In addition, since you can use the computer's keyboard, entering characters required for the setup is easier.
Use Microsoft Internet Explorer 6.0 or later as the Web browser. If using a
Mac OS, use Safari or Firefox.
a
If you set Standby Mode to Communication On , you can use a Web browser to make settings and perform control even if the projector is in standby mode (when the power is off).
s Extended - Standby Mode
Projector setup
In a Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
There are also items that can only be set in a Web browser.
Monitoring and Controlling
109
Items in the Configuration menu that cannot be set by a Web browser
•
Settings menu - Keystone - Quick Corner
•
Settings menu - Pointer Shape
•
Settings menu - Pattern
•
Settings menu - User Button
•
Extended menu - User's Logo
•
Extended menu - Language
•
Extended menu - Operation - High Altitude Mode
•
Reset menu - Reset All and Reset Lamp Hours
The settings for items on each menu are the same as the projector's
Configuration menu.
s
Items that can only be set with a Web browser
•
SNMP Community Name
•
Monitor Password
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
Make sure the computer and projector are connected to the network. Use
Advanced when connecting via a Wireless LAN.
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need to make settings so that a proxy server is not used for a connection.
a Start a Web browser on the computer.
b Enter the IP address of the projector in the address input box of the Web browser, and press the Enter key on the computer's keyboard.
The Web Control screen is displayed.
When Web Control Password is set in the Network menu from the projector's Configuration menu, the password entry screen is displayed.
Displaying the Web Remote screen
The Web Remote function allows you to perform projector remote control operations with a Web browser.
a b
Display the Web Control screen.
Click Web Remote .
c The Web Remote screen is displayed.
Monitoring and Controlling
110
Name
F [Page] buttons
[Up] [Down]
G [Source Search] button
Name
A [ t ] button
B [Computer] button
C
D
E
[Video] button
[Freeze] button
[A/V Mute] button
Function
Turns the projector power on or off.
s
"From Installation to Projection" p.28
Each time you press the button, the input changes between images from the Computer1 port and the Computer2 port.
Each time the button is pressed, the image cycles through
Video, S-Video, and HDMI ports.
Pauses or resumes image playback.
s
"Freezing the Image (Freeze)" p.44
Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
H [LAN] button
I [USB] button
J [Volume] buttons
[ a ][ b ]
Function
Changes pages in files such as PowerPoint files when using the following projection methods.
•
When using the Wireless Mouse function s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
•
When using USB Display s
"Projecting with USB Display" p.30
•
When connecting to a network
When projecting images using Slideshow, pressing these buttons displays the previous/next image file.
Switches to the image from the input port where video signals are being input.
s
"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.29
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to that image.
s
"Switching to the Target Image Using the Remote
Each time the button is pressed, it cycles through the following images:
•
USB Display
•
Images from the device connected to the USB(TypeA) port s
"Switching to the Target Image Using the Remote
[ a ] Decreases the volume.
[ b ] Increases the volume.
s
Monitoring and Controlling
111
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset email addresses when a problem or warning occurs with a projector. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.
s Network - Mail - Mail Notification
a •
Up to a maximum of three notification destinations (addresses) can be registered, and notification messages can be sent to all three destinations at once.
• If a projector develops a critical problem and suddenly stops working, it may not be able to send a message notifying an operator of the problem.
• Controlling is possible if Standby Mode is set to Communication
On , even if the projector is in standby state (when the power is off).
s Extended - Standby Mode
•
Internal error
•
Fan related error
•
Sensor error
•
Lamp timer failure
•
Lamp out
•
Internal temperature error
•
High-speed cooling in progress
•
Lamp replacement notification
•
No-signal
No Signal is input to the projector. Check the connection status or check that the power for the signal source is turned on.
•
Auto Iris Error
•
Power Err. (Ballast)
See the following to deal with problems or warnings.
s
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent.
Subject: EPSON Projector
Line 1: The name of the projector where the problem occurred
Line 2: The IP address set for the projector where the problem has occurred.
Line 3 and on: Details of the problem
The details of the problem are listed line by line. The main message contents are listed below.
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages are sent to the specified computer when a problem or warning occurs. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.
s
Network - Others - SNMP
Monitoring and Controlling
112 a •
SNMP should be managed by a network administrator or someone who is familiar with the network.
•
To use the SNMP function to monitor the projector, you need to install the SNMP manager program on your computer.
•
The managing function using SNMP cannot be used via wireless
LAN in Quick connection mode.
•
Up to two destination IP addresses can be saved.
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
Item
HDMI
Video
S-Video
USB Display
USB
LAN
A/V Mute ON/OFF On
Off
RGB
Component
Command
SOURCE 21
SOURCE 24
SOURCE 30
SOURCE 41
SOURCE 42
SOURCE 51
SOURCE 52
SOURCE 53
MUTE ON
MUTE OFF
Add a Carriage Return (CR) code (0Dh) to the end of each command and transmit.
For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Command list
When the power ON command is transmitted to the projector, the power turns on and it enters warm-up mode. When the projector's power has turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message is output and a ":" is returned.
The main contents are listed below.
Power ON/OFF
Signal selection
Item
On
Off
Computer1
Computer2
Auto
RGB
Component
Auto
Command
PWR ON
PWR OFF
SOURCE 1F
SOURCE 11
SOURCE 14
SOURCE 2F
Cable layouts
Serial connection
•
Connector shape: D-Sub 9-pin (male)
Monitoring and Controlling
•
Projector input port name: RS-232C
<At the projector>
<At the projector>
Signal Name
GND
TD
RD
Function
Signal wire ground
Transmit data
Receive data
Communications protocol
• Default baud rate setting: 9600 bps
• Data length: 8 bit
• Parity: None
•
Stop-bit: 1 bit
• Flow control: None
113
<At the computer>
(PC serial cable) <At the computer>
About PJLink
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for controlling network-compatible projector's as part of their efforts to standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
See the following for more information on network settings related to
PJLink.
s
It complies with all commands except for the following commands defined by PJLink Class1, and agreement was confirmed by the PJLink standard adaptability verification.
URL: http://pjlink.jbmia.or.jp/english/
•
Non-compatible commands
Mute settings
Function
Image muting set
Audio muting set
PJLink Command
AVMT 11
AVMT 21
•
Input names defined by PJLink and corresponding projector sources
Source PJLink Command
Computer1
Computer2
Video
S-Video
HDMI
USB
INPT 11
INPT 12
INPT 21
INPT 22
INPT 32
INPT 41
Monitoring and Controlling
114
LAN
USB Display
Source
INPT 52
INPT 53
PJLink Command
• Manufacturer name displayed for "Manufacture name information query"
EPSON
•
Model name displayed for "Product name information query"
EB-420/CS500XN/PowerLite 420
EB-425W/CS500WN/PowerLite 425W
EB-435W/CS520WN/PowerLite 435W
EB-430/CS510XN/PowerLite 430
•
Monitoring and control with application software
You can use Crestron RoomView ® Express or Crestron RoomView ®
Server Edition provided by Creston ® to monitor devices in the system, to communicate with the help desk, and to send emergency messages. See the following Web site for details.
http://www.crestron.com/getroomview
This manual describes how to perform operations on your computer using a Web browser.
a • You can only enter single-byte alphanumeric characters and symbols.
• The following functions cannot be used while using Crestron
RoomView ® .
s
"Changing Settings Using a Web Browser (Web Control)" p.108
Message Broadcasting (EasyMP Monitor plug-in)
• Controlling is possible if Standby Mode is set to Communication
On , even if the projector is in standby state (when the power is off).
s Extended - Standby Mode
About Crestron RoomView
®
Crestron RoomView ® is an integrated control system provided by
Crestron ® . It can be used to monitor and control multiple devices connected on a network.
The projector supports the control protocol, and can therefore be used in a system built with Crestron RoomView ® .
Visit the Crestron ® Web site for details on Crestron RoomView ® .
http://www.crestron.com
The following provides an overview of Crestron RoomView ® .
•
Remote operation using a Web browser
You can operate a projector from your computer just like using a remote control.
Operating a projector from your computer
Displaying the operation window
Check the following before carrying out any operations.
•
Make sure the computer and projector are connected to the network.
When communicating with a wireless LAN, connect in Advanced connection mode.
s
•
Set Crestron RoomView to On from the Network menu.
s
Network - Others - Crestron RoomView
Monitoring and Controlling a b
Start a Web browser on the computer.
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
The operation window is displayed.
Using the operation window
A You can perform the following operations when you click the buttons.
Power
Button
Vol-/Vol+
Function
Turns the projector power on or off.
Adjusts the volume.
115
A/V Mute
Freeze
Button
Contrast
Button
Brightness
Color
Sharpness
Zoom
Function
Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
B Switch to the image from the selected input source. To display input sources that are not shown on the screen, click (a) or (b) to scroll up or down.
You can change the source name if necessary.
C You can perform the following operations when you click the buttons. To display buttons that are not shown on the screen, click (c) or (d) to scroll left or right.
Function
Pauses or resumes image playback.
s
"Freezing the Image (Freeze)" p.44
You can adjust the difference between light and dark in the images.
You can adjust the image brightness.
You can adjust the color saturation for the images.
You can adjust the image sharpness.
Click the [ z ] button to enlarge the image without changing the projection size. Click the [ x ] button to reduce an image that was enlarged with the [ z ] button.
Click the [ ], [ ], [ ], or [ ] button to change the position of an enlarged image.
s
"Enlarging Part of the Image (E-Zoom)" p.46
D
[ ], [ ], [ ], or [ ] buttons have the same effects as [ ][ ][ ][ ] buttons on the remote control. You can perform the following operations when you click the other buttons.
Monitoring and Controlling
OK
Menu
Auto
Search
Esc
Button Function
Performs the same operation as the [ ] button on the remote control.
s
Displays and closes the Configuration menu.
If clicked while projecting analog RGB signals from
Computer1 port or Computer2 port, automatically optimizes the image by adjusting the Tracking, Sync., and Position.
Switches to the image from the input port where video signals are being input.
s
"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.29
Performs the same operation as the [Esc] button on the remote control.
s
E You can perform the following operations when you click the tabs.
Tab
Contact IT Help
Info
Tools
Function
Displays the Help Desk window. Used to send messages to, and receive messages from, the administrator using
Crestron RoomView ® Express.
Displays information on the projector that is currently connected.
Changes settings in the projector that is currently connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the operation window. You can use this window to change settings in the projector that is currently connected.
116
A Crestron Control
Make settings for Crestron ® central controllers.
B Projector
The following items can be set.
Item
Projector Name
Location
Assigned To
Function
Enter a name to differentiate the projector that is currently connected from other projectors on the network. (The name can contain up to 15 single-byte alphanumeric characters.)
Enter an installation location name for the projector that is currently connected on the network. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)
Enter a user name for the projector. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)
Monitoring and Controlling
DHCP
Send
Item
IP Address
Subnet Mask
Default Gateway
Function
Select the Enabled check box to use DHCP. You cannot enter an IP address if DHCP is enabled.
Enter the IP address to assign to the currently connected projector.
Enter a subnet mask for the currently connected projector.
Enter the gateway address for the currently connected projector.
Click this button to confirm the changes made to the
Projector .
C Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item
New Password
Confirm
Send
Function
Enter the new password when changing the password to open the Tools window. (The name can contain up to 26 single-byte alphanumeric characters.)
Enter the same password as you entered in New
Password . If the passwords are not the same, an error is displayed.
Click this button to confirm the changes made to the
Admin Password .
D User Password
Select the Enabled check box to require a password to open the operation window on the computer.
The following items can be set.
Item
New Password
Confirm
Send
117
Function
Enter the new password when changing the password to open the operation window. (The name can contain up to 26 single-byte alphanumeric characters.)
Enter the same password as you entered in New
Password . If the passwords are not the same, an error is displayed.
Click this button to confirm the changes made to the
User Password .
Optional Accessories and Consumables
118
The following optional accessories and consumables are available. Please purchase these products as and when needed.The following list of optional accessories and consumables is current as of: August 2011. Details of accessories are subject to change without notice.
Optional Accessories
Document Camera ELPDC06/ELPDC11
Use when projecting images such as books, OHP documents, or slides.
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector.
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
These are extension cables for when the computer cable supplied with the projector is too short.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male ^ 3)
Use to connect a Component Video
source.
Wireless LAN unit ELPAP07
Use when connecting the projector to a computer wirelessly and projecting.
Quick Wireless Connection USB Key ELPAP08
Use when you want to quickly establish one-to-one connection between the projector and a computer with Windows installed.
Wall mount * ELPMB27
Use this arm type fitting when installing the projector on a wall.
Interactive Unit ELPIU03
Use when operating the computer screen on the projection surface.
Ceiling mount * ELPMB23
Use when installing the projector on a ceiling.
Ceiling pipe (450 mm) * ELPFP13
Ceiling pipe (700 mm) * ELPFP14
Use when installing the projector on a high ceiling.
* Special expertise is required to suspend the projector. Contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Consumables
Lamp unit (for EB-425W/EB-420) ELPLP60
Lamp unit (for EB-435W/EB-430) ELPLP61
Use as a replacement for a used lamp.
Air filter ELPAF36
Use as a replacement for a used air filter.
Screen Size and Projection Distance
Projection Distance (For EB-430/EB-420)
A Projection distance
B Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a wall or ceiling)
C Center of lens
119
4:3 Screen Size
50"
60"
70"
80"
90"
100"
108"
100x76
120x91
140x105
160x120
180x135
200x150
219x165
* Project using Wide (maximum zoom).
A
Minimum (Wide) to Maximum
(Tele)
55 - 75
66 - 90
78 - 106
89 - 122
101 *
112 *
122 *
Unit: cm
B
Minimum
(Wide)
6
8
9
10
12
13
14
16:9 Screen Size
50"
60"
70"
80"
90"
99"
110x62
130x75
150x87
180x100
200x110
219x123
* Project using Wide (maximum zoom).
A
Minimum (Wide) to Maximum
(Tele)
60 - 82
72 - 99
85 - 116
98 *
110 *
121 *
Unit: cm
B
Minimum
(Wide)
17
21
24
28
31
34
Screen Size and Projection Distance
Projection Distance (For EB-435W/EB-425W)
A Projection distance
B Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a wall or ceiling)
C Center of lens
120
4:3 Screen Size
50"
60"
70"
80"
90"
102"
100x76
120x91
140x105
160x120
180x135
207x155
* Project using Wide (maximum zoom).
A
Minimum (Wide) to Maximum
(Tele)
58 - 79
70 - 96
82 - 112
94 *
107 *
121 *
Unit: cm
B
Minimum
(Wide)
9
11
13
14
16
18
16:9 Screen Size
60"
70"
80"
90"
100"
113"
130x75
150x87
180x100
200x110
220x120
250x141
* Project using Wide (maximum zoom).
A
Minimum (Wide) to Maximum
(Tele)
63 - 87
74 - 101
85 - 116
97 *
108 *
122 *
Unit: cm
B
Minimum
(Wide)
14
16
19
21
23
26
16:10 Screen Size
55"
60"
115x72
130x81
A
Minimum (Wide) to Maximum
(Tele)
56 - 77
61 - 84
Unit: cm
B
Minimum
(Wide)
9
9
Screen Size and Projection Distance
16:10 Screen Size
70"
80"
90"
100"
116"
150x94
170x110
190x120
220x130
251x157
* Project using Wide (maximum zoom).
A
Minimum (Wide) to Maximum
(Tele)
72 - 99
83 - 113
94 *
105 *
122 *
B
Minimum
(Wide)
11
13
14
16
18
121
Supported Monitor Displays
Supported Resolutions
Computer signals (analog RGB)
Signal
VGA
SVGA
XGA
WXGA
WXGA+
SXGA
SXGA+
WSXGA+
UXGA
*
MAC13”
MAC16”
MAC19”
1, 2
Refresh Rate (Hz)
60/72/75/85
56/60/72/75/85
60/70/75/85
60
60
60/75/85
60/75/85
70/75/85
60/75/85
60/75/85
60/75
60
60
67
75
75
59
75
Resolution (dots)
640x480
800x600
1024x768
1280x768
1360x768
1280x800
1440x900
1152x864
1280x1024
1280x960
1400x1050
1680x1050
1600x1200
640x480
832x624
1024x768
1024x768
1152x870 MAC21”
* 1 EB-435W/EB-425W only
* 2 Only compatible when Wide is selected as the Resolution from the
Configuration menu.
Images may also be projected when signals other than the above are input.
However, some functions may be limited.
Component Video
Signal
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1080i)
Composite video
Signal
TV (NTSC)
TV (SECAM)
TV (PAL)
Refresh Rate (Hz)
60
50
60
50
50/60
50/60
Refresh Rate (Hz)
60
50
50/60
Input signal from the HDMI port
Signal
VGA
SVGA
XGA
WXGA
SXGA
SXGA+
UXGA
Refresh Rate (Hz)
60
60
60
60
60
60
60
60
Resolution (dots)
720x480
720x576
720x480
720x576
1280x720
1920x1080
Resolution (dots)
720x480
720x576
720x576
Resolution (dots)
640x480
800x600
1024x768
1280x800
1280x960
1280x1024
1400x1050
1600x1200
122
Supported Monitor Displays
Signal
SDTV (480i/480p)
SDTV (576i/576p)
HDTV (720p)
HDTV (1080i)
HDTV (1080p)
Refresh Rate (Hz)
60
50
50/60
50/60
24/30/50/60
Resolution (dots)
720x480
720x576
1280x720
1920x1080
1920x1080
123
Specifications
Projector General Specifications
Product name
Dimensions
LCD panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Lamp
Max. audio output
Speaker
Power supply
Power consumption
100 to 120 V area
220 to 240 V area
Operating altitude
Operating temperature
Storage temperature
Mass
EB-435W
0.59" Wide
EB-430 EB-425W
345 (W) x 105 (H) x 277 (D) mm (not including raised section)
0.55" 0.59" Wide
EB-420
0.55"
1,024,000
WXGA (1280 (W)x 800 (H) dots)x 3
Polysilicon TFT active matrix
786,432
XGA (1024 (W) x 768 (H) dots)x 3
Manual
1,024,000
WXGA (1280 (W)x 800 (H) dots)x 3
Digital (1-1.35)
UHE lamp, 230 W Model No.: ELPLP61
786,432
XGA (1024 (W) x 768 (H) dots)x 3
UHE lamp, 200 W Model No.: ELPLP60
16 W
1
100 to 240V AC ±10%, 50/60 Hz 3.4 to 1.5 A
Operating: 332 W
Standby power consumption (Communication On): 6.8 W
Standby power consumption (Communication Off): 0.28 W
Operating: 316 W
Standby power consumption (Communication On): 7.3 W
Standby power consumption (Communication Off): 0.37 W
Operating: 294 W
Standby power consumption (Communication On): 6.2 W
Standby power consumption (Communication Off): 0.29 W
Operating: 283 W
Standby power consumption (Communication On): 6.8 W
Standby power consumption (Communication Off): 0.39 W
Altitude 0 to 2,286 m
+5 to +35°C (No condensation)
Approx. 3.9 kg
100 to 240V AC ±10%, 50/60 Hz 3.0 to 1.3 A
-10 to +60°C (No condensation)
Approx. 3.9 kg Approx. 3.8 kg Approx. 3.8 kg
Connectors Computer1 port
Computer2 port
1
1
Mini D-Sub15-pin (female)
Mini D-Sub15-pin (female)
124
Specifications
Video port
S-Video port
Audio1 port
Audio2 port
Audio-L/R port
Mic port
Audio Out port
Monitor Out port
HDMI port
USB(TypeA) port *
USB(TypeB) port *
USB port
(dedicated Wireless LAN unit)
LAN port
RS-232C port
1
1
1
1
1
1
1
1
1
1
1
1
1
1
* Supports USB 2.0. However, the operation of all USB compatible devices is not guaranteed.
RCA pin jack
Mini DIN 4-pin
Stereo mini pin jack
Stereo mini pin jack
RCA pin jack x 2 (L-R)
Stereo mini pin jack
Stereo mini pin jack
Mini D-Sub15-pin (female)
HDMI (Audio is only supported by PCM)
USB connector (Type A)
USB connector (Type B)
USB connector (Type A)
RJ-45
Mini D-Sub 9-pin (male)
125
Specifications
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 15˚ it could be damaged and cause an accident.
126
Specifications
127
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Trade Name: EPSON
Type of Product:
Model:
LCD Projector
H447C/H448C/H449C/H469C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
Appearance
A Center of lens
B Measurements from the center of the lens to the wall mount plate fixing points or the ceiling mount fixing points.
128
Units: mm
Glossary
129
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
AMX Device Discovery
Aspect Ratio
Component Video
Composite video
Contrast
DHCP
Gateway Address
HDCP
HDTV
Interlace
IP Address
Progressive
SDTV
SNMP
AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
See the AMX Web site for more details.
URL http://www.amx.com/
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
Pr).
A method that combines the video signal into a luminance component and a color component for transmission down a single cable.
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called "contrast adjustment".
to equipment connected to a network.
This is a server (router) for communicating across a network (subnet) divided according to subnet mask
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by
HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressive
•
of 16:9
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
A number to identify a computer connected to a network.
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount of flicker in images decreases because the volume of information has doubled compared with an interlace system.
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV
Definition Television.
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network.
Glossary sRGB
SSID
Subnet Mask
SVGA
S-Video
SXGA
Sync.
Tracking
Trap IP Address
VGA
XGA
130
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source to sRGB.
SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices that correspond to SSID.
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
A method that separates the video signal into a luminance component (Y) and a color component (C).
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If tracking is not carried out correctly, wide vertical stripes appear in the signal.
for the destination computer used for error notification in SNMP.
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
General Notes
131
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
About Notations
Microsoft ® Windows ® 98 operating system
Microsoft ® Windows ® Me operating system
Microsoft ® Windows ® 2000 operating system
Microsoft ® Windows ® XP Professional operating system
Microsoft ® Windows ® XP Home Edition operating system
Microsoft ® Windows Vista ® operating system
Microsoft ® Windows ® 7 operating system
In this guide, the operating systems above are referred to as "Windows 98",
"Windows Me", "Windows 2000", "Windows XP", "Windows Vista", and
"Windows 7". Furthermore, the collective term Windows may be used to refer to Windows 98, Windows Me, Windows 2000, Windows XP,
Windows Vista, and Windows 7, and multiple versions of Windows may be referred to as, for example, Windows 98/Me/2000/XP/Vista, with the
Windows notation omitted.
Mac OS X 10.3.x
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
In this guide, the operating systems above are referred to as "Mac OS X
10.3.9", "Mac OS X 10.4.x", "Mac OS X 10.5.x", and "Mac OS X 10.6.x".
Furthermore, the collective term "Mac OS" is used to refer to them.
General Notice:
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corp.
Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
WPA ™ and WPA2 ™ are registered trademarks of Wi-Fi Alliance.
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2011. All rights reserved.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement