Kongsberg cNODE Modem
Embed
Quick Reference Guide
Installing the cNODE Modem Embed cables
Procedure
1 Connect the transducer cable.
If you have a cable kit, the wires are already connected to the connectors.
2 Prepare 8 wires with the appropriate length for the modem interface.
3 Install a crimp terminal in one end of each cable.
4 Install the crimp terminals in a Molex 8–pin receptacle according to the cable drawing.
5 Connect J3 to P3 on the top of the PCB.
6 Prepare 2 red and 2 black wires with the appropriate length for the power.
7 Install a crimp terminal in one end of each cable.
8 Install the crimp terminals in a Molex 4–pin receptacle according to the cable drawing.
9 Connect J4 to P4 in the front on the PCB.
10 Prepare 3 wires with the appropriate length for the service interface.
11 Install a crimp terminal in one end of each cable.
12 Install the crimp terminals in a Molex 8–pin receptacle according to the cable drawing.
13 Connect J5 to P5 in the front on the PCB.
Installing the transducer cables TD80V
Prerequisites
Procedure
1 Use a yellow wire (0.5 mm 2 ) and connect the white wire from the transducer with both capacitors and the yellow wire from the transformer.
2 Use a red wire (0.5 mm 2 ) and connect the black wire from the transducer with both capacitors and the red wire from the transformer.
431016 / A / 2019–11–15
3 Use a black wire (0.5 mm 2 ) and connect two wires in parallel to the black wire from the transformer.
4 Use a green wire (0.24 mm 2 ) and connect two wires to the green wire from the transducer.
5 Use an orange wire (0.24 mm 2 ) and connect to the orange wire from the transducer.
6 Add crimp terminals to the end of the wires.
7 Install the crimp terminals in a Molex 8-pin receptacle.
a Connect the green wires to pin 1 and 5 on the receptacle.
b Connect the black wires to pin 3 and 7 on the receptacle.
c Connect the blue wires to pin 4 and 8 on the receptacle.
d Connect the orange wire to pin 6 on the receptacle.
This is now receptacle J1.
8 Connect receptacle J1 to connector P1 on the front of the PCB.
Installing the transducer cables TD180
Prerequisites
Procedure
1 Use a yellow wire (0.5 mm 2 ) and connect the white wire from the transducer with the yellow wire from the transformer.
2 Use a red wire (0.5 mm 2 ) and connect the black wire from the transducer with the red wire from the transformer.
3 Use a black wire (0.5 mm 2 ) and connect two wires in parallel to the black wire from the transformer.
4 Use a green wire (0.24 mm 2 ) and connect two wires to the green wire from the transducer.
5 Use an orange wire (0.24 mm 2 ) and connect to the orange wire from the transducer.
6 Add crimp terminals to the end of the wires.
7 Install the crimp terminals in a Molex 8-pin receptacle.
a Connect the green wires to pin 1 and 5 on the receptacle.
b Connect the black wires to pin 3 and 7 on the receptacle.
c Connect the blue wires to pin 4 and 8 on the receptacle.
d Connect the orange wire to pin 6 on the receptacle.
431016 / A / 2019–11–15
This is now receptacle J1.
8 Connect receptacle J1 to connector P1 on the front of the PCB.
Transducer connector pinout J1
This is the pin configuration for a female plug, as seen towards the plug (face view).
4
5
2
3
6
7
8
Pin number
1
Colour
Green
Black
Blue
Green
Orange
Black
Blue
Signal
ID data
Screen
TD +
TD –
ID data
Ground
RS-485 Data +
RS-485 Data –
Minimum requirements
0.24 mm 2
0.5 mm 2
0.5 mm 2
0.24 mm 2
0.24 mm 2
0.5 mm 2
0.5 mm 2
Modem interface connector pinout J3
This is the pin configuration for a female plug, as seen towards the plug (face view).
Pin number
3
4
1
2
5
Signal
RS-232 Tx
RS-232 Rx
Ground
RS-422 Tx +
RS-422 Tx –
431016 / A / 2019–11–15
Minimum requirements
0.5 mm 2
0.5 mm 2
0.5 mm 2
0.5 mm 2
0.5 mm 2
Pin number
6
7
8
Signal
RS-422 Rx +
RS-422 Rx –
Ground
Minimum requirements
0.5 mm 2
0.5 mm 2
0.5 mm 2
Power connector J4
This is the pin configuration for a female plug, as seen towards the plug (face view).
Pin number
3
4
1
2
Colour
Red
Red
Black
Black
Signal
External power (24 VDC)
External power (24 VDC)
Ground
Ground
Minimum requirements
0.5 mm 2
0.5 mm 2
0.5 mm 2
0.5 mm 2
431016 / A / 2019–11–15
Service connector J5
This is the pin configuration for a female plug, as seen towards the plug (face view).
8
9
10
6
7
4
5
Pin number
1
2
3
Signal
Responder trigger +
Not connected
Not connected
Ground
Not connected
Responder trigger –
Not connected
Not connected
RS-232 Tx
RS-232 Rx
Minimum requirements
0.5 mm 2
0.5 mm 2
0.5 mm 2
0.5 mm 2
0.5 mm 2
Support information
Should you need technical support for your cNODE Modem Embed you must contact a Kongsberg
Maritime office. A list of all our offices is provided on our website. You can also contact our main support office in Norway.
Manuals and technical information can be downloaded from our support website.
Company name
Address
Telephone
Telephone 24h support
Telefax
Website
Support website
E-mail address
Kongsberg Maritime AS
Strandpromenaden 50, 3183 Horten, Norway
+47 33 03 41 00
+47 33 03 24 07
+47 33 04 76 19 https://www.kongsberg.com/maritime/
Product support A to Z [email protected]
431016 / A / 2019–11–15
