Control 4 C4-16S2-E-B Installation And User Manual
The Control 4 C4-16S2-E-B is a powerful and versatile audio matrix switch that allows you to connect up to 16 audio sources to 16 different zones in your home. With adjustable gain, treble, bass, and balance for each zone, you can customize your listening experience to perfection. The front display makes it easy to see what's playing and adjust settings on the fly. Plus, with Ethernet and ZigBee connectivity, you can control the switch from anywhere in your home using the Control4 app or a compatible remote control.
Annonce
Annonce
Disclaimer
Control4
®
makes no representations or warranties with respect to this publication, and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. Control4 reserves the right to make changes to any and all parts of this publication at any time, without any obligation to notify any person or entity of such changes.
Trademarks
Control4 and the Control4 logo are trademarks or registered trademarks of
Control4 Corporation. Other product and company names mentioned in this document may be the trademarks or registered trademarks of their respective owners.
Copyright
Copyright © 2004-2008 Control4. All rights reserved. No part of this publication may be reproduced, photocopied, stored on a retrieval system, or transmitted without the express written consent of the publisher.
Contact Us
Control4 Corporation
11734 S. Election Road
Salt Lake City, UT 84020 USA http://www.control4.com
Audio Matrix Switch - 16 Installation and User Guide
Part Number: 200-00039 Rev C (Draft 2)
Hardware Model Number: C4-16S2-E-B
Contents
Important Information .................................... 1
Safety Instructions ................................. 1
Graphical Symbols on the Device.......... 3
Graphical Symbols in this Guide............ 3
Additional Resources ............................. 4
Introduction to the Audio Matrix Switch ......... 5
Features and Benefits............................ 5
Network Requirements .......................... 5
What’s in the Box ................................... 6
About the Audio Matrix Switch ............... 6
Front View......................................... 6
Back View ......................................... 7
Source Inputs.................................... 7
Audio Outputs ................................... 7
Front Display..................................... 8
Technical Specifications ................... 9
Set Up the Audio Matrix Switch ................... 11
Plan Your Physical Layout ................... 11
Connect Input and Output Devices ...... 14
Connect to the Network and Power ..... 14
Set Up Logical Connections ................ 14
Network Configuration ......................... 15
Use Audio Matrix Switch.............................. 19
View Output Assignments.................... 19
Manage Outputs .................................. 20
View Output Assignments............... 20
Configure an Output ....................... 21
Check Signal Status ....................... 22
View Network Settings ......................... 23
Set Front Display Preferences ............. 23
i
Chapter 4 Regulatory Compliance and Warranty......... 25
Regulatory Compliance ....................... 25
FCC ................................................ 25
Industry Canada ............................. 26
Edison Test Lab (ETL).................... 26
CE Declaration of Conformity ......... 27
Warranty .............................................. 28
Index ..................................................................................... 29
ii
P R E F A C E
Important Information
Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when
1
2 moving the cart/apparatus combination to avoid injury from tip-over.
13.
Unplug this apparatus during lighting storms or when unused for long periods of time.
14.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as when a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING! Do not expose the apparatus to dripping or splashing. Do not place objects filled with liquids near the apparatus.
WARNING! To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.
WARNING! Equipment must be connected to a
Mains socket outlet with a protective earthing connection.
Graphical Symbols on the Device
The following information is placed on the device:
Graphical Symbols in this Guide
Warning, Caution, Note, and Tip paragraphs draw your attention to important safe practices and additional information which may help you avoid injury, death, or loss of material or time.
WARNING! This indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury. DO NOT IGNORE A WARNING!
CAUTION! This indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. DO NOT IGNORE A CAUTION!
3
IMPORTANT! This indicates information that will help you avoid damage to your equipment, loss of materials, or loss of time. PAY ATTENTION TO THESE IMPORTANT
STATEMENTS!
NOTE: This indicates a note on related information about the current topic.
TIP: This indicates a tip that may save you time or effort.
Additional Resources
The following resources are available:
`
Your Control4-authorized reseller
`
Control4 Web Site: http://www.control4.com/
4
C H A P T E R 1
Introduction to the Audio
Matrix Switch
Control4 systems are uniquely configured for every customer and every site. A popular component among music lovers is the Control4 Audio Matrix Switch.
This chapter introduces the Control4 Audio Matrix Switch and its features.
Features and Benefits
`
Switches up to 16 input sources to up to 16 simultaneous output zones.
`
Adjustable gain, treble, bass, and balance for each zone
`
Audio sensing on inputs
`
Device chassis is three standard rack units (RU) tall and rack mountable conforming to EIA 19” rack standards (5.25” x 17.34” x 14”)
`
Communicates with control devices via Ethernet
10/100 port and ZigBee (a wireless standard for mesh-networking).
`
Backlighting feature turns on with any button push or
Select Dial push and stays lit for a preset time (default is 30 seconds).
Network Requirements
In order for the Audio Matrix Switch to be managed and controlled from the Control4 user interfaces, it must communicate with the system through either a wired
(Ethernet) or wireless (ZigBee 802.15.4 mesh) network. If you want to use an Ethernet connection for the Audio
5
Matrix Switch, ensure that your home network wiring is in place before starting system setup.
What’s in the Box
The following items are included in your Control4 Audio
Matrix Switch box.
`
Control4 Audio Matrix Switch
`
IEC power cord
`
This manual
About the Audio Matrix Switch
Front View
1 2 3
1. Front Display —For displaying or setting audio switch settings and navigating system menus
2. Buttons —For choosing options or menus displayed in the front panel user interface
3. Select Dial —For scrolling through and selecting screen elements or options displayed in the LCD
6
Back View
1 2 3 4
1. Power Plug Port —For standard IEC cord
(included). Supports universal AC input
(100-240 VAC 50/60 Hz).
2. Ethernet —RJ-45 for a 10/100 Mb Ethernet connection
3. Audio In (Left-Right pairs) 1-16 —RCA jacks for stereo channel input for up to 16 stereo analog sources
4. Audio Out (Left-Right pairs) 1-16 —RCA jacks for stereo channel line output for up to 16 amplifiers
Source Inputs
Each of the 16 signal sensing analog audio inputs (the
RCA style ports) is labeled 1-16 for each individual source.
Audio Outputs
The system automatically creates generic source names displayed in the front of the device. To change these names, you must update your system using supported system designing software (such as Composer Pro on a
PC). For more information, refer to the documentation that shipped with your Control4 controller or contact your professional installer or reseller.
7
Front Display
The best method of initially setting up system routing for the Audio Matrix Switch is using Composer Pro software on a PC (for trained installers only). You can also make adjustments from the front display.
The front display allows you to set or change audio source routing and change zone settings for volume, bass, treble, and mute. The display also shows the current source and zone activity.
8
Technical Specifications
Table 1-1. Audio Matrix Switch Technical Specifications
Inputs
# of Channels
Input Connectors
Input Impedance
Nominal Input Level
Maximum Input Level
16 L/R Stereo Pairs
RCA Jacks
10 k
Ω
typical
-14 dBV
+4 dBV
Outputs
# of Channels
Output Connectors
Output Impedance
Nominal Output Level
Maximum Output Level
16 L/R Stereo Pairs
RCA Jacks
50
Ω
typical
-14 dBV
+4 dBV
Zone (Output) Control:
Available Gain
Treble
Bass
Balance
Mute (-75 dB) to -40 to +8 dB
-12 to +12 dB, 2 dB steps, High Shelving EQ
-12 to +12 dB, 2 dB steps, Low Shelving EQ
L / R
Input Power Requirement:
Voltage 100-240V~
Frequency
Amps
Watts
50/60 Hz
.08 Amps
8 Watts
9
10
C H A P T E R 2
Set Up the Audio Matrix
Switch
This device operates as part of the Control4 home system, which requires physical and logical connections to function as designed.
Essential setup tasks include:
2.Connect Input and Output Devices
3.Connect to the Network and Power
5.Static IP Modifications
This chapter describes, in general terms, how to set up physical connections required for the Audio Matrix Switch and all associated devices. Refer to any device-specific documentation for additional installation instructions.
To set up the logical connections required, refer to
Control4 Composer Pro User Guide software documentation.
Plan Your Physical Layout
This section explains physical and logical connections and can help you plan your physical connections.
Use a worksheet to plan your audio zones. Using the
worksheet provided in Table 1 on page 12, identify the
ports you will use for each planned devices and zones.
11
12
Table 1: Audio Matrix Switch Routing Worksheet
14.
15.
16.
10.
11.
12.
13.
8.
9.
6.
7.
4.
5.
2.
3.
RCA
Pair
#
Audio In
Sources— RCA
(Left-Right) pairs for stereo channel input for up to 16 stereo analog sources
1.
Audio Out Zones —
RCA (Left-Right) pairs for stereo channel output for up to 16 output zones
13
Connect Input and Output Devices
1.
Connect audio source devices (such as CD changers or players, tuners, iPods, or tape players) you want included in the system to the audio in jacks.
2.
Connect amplifiers or amplified speakers as needed to the audio out jacks.
NOTE: If you are not sure which jacks to use, try using
the worksheet provided in Table 1 to plan your routes.
Connect to the Network and Power
1.
If you are using an Ethernet connection for the Audio
Matrix Switch, plug the data cable from the home network connection into the Audio Matrix Switch RJ-
45 port (labeled Ethernet) and the network port in your wall or at the network hub or switch.
2.
Connect the power cord provided to the back of the
Audio Matrix Switch and to the power outlet. Once the power cord is connected, the Audio Matrix Switch should power up.
Set Up Logical Connections
Physical and logical connections are required in order to control, navigate, and use the Audio Matrix Switch as designed.
Thus far you have set up the physical connections for the
Control4 Audio Matrix Switch. To complete the logical setup, trained installers must use a PC connected (and with Control4 Composer software installed) to the home network. If you are a trained Control4 installer, refer to the
Control4 Composer User Guide .
14
Network Configuration
To set the network configuration:
1.
At the In to Out Assignments screen, press the
Network button.
2.
On the Network Configuration screen, choose an
Ethernet or ZigBee network by rotating and pressing the Select Dial.
IMPORTANT! When making logical connections in
Composer, identify the device as the network type
(Ethernet or Zigbee) that you choose on the device network configuration. To avoid unexpected behavior, do not identify the device as both network types.
3.
If the switch is set to use a ZigBee network, the EUID,
Gateway, and ZigBee channel number are displayed.
This screen has two menu options:
`
Identify: When identifying the switch in
Composer, press this button.
`
Back: Returns to the Network Configuration screen.
4.
If the switch is set to use an Ethernet network, the
MAC address, method of obtaining a network IP address, the device’s IP address, Subnet Mask, and
Gateway are displayed.
15
16
The Audio Matrix Switch, by default, uses DHCP to obtain a network IP address.
If the local area network does not support DHCP, you can configure the switch to use a Static IP address instead:
4a. Press the Select Dial to enter Edit mode.
4b. Press the Down or Up button (or rotate the
Select Dial) to choose Static IP.
4c. Press OK (or press the Select Dial).
4d. Press Save (or press the Select Dial).
4e. Edit the IP, Mask, and GWay fields for the
Static IP network: Use the Select Dial to select a line, then press the dial.
Use the Select Dial to scroll the number up or down and edit as needed, then press the
Select Dial to move to the next field within the number.
4f. When finished editing, press Save.
17
18
C H A P T E R 3
Use Audio Matrix Switch
This chapter introduces the user interface available to
Audio Matrix Switch users and common system tasks you can perform with the Audio Matrix Switch from the front display.
NOTE: Following initial setup, you may never need to manually change settings on the Audio Matrix Switch.
This device is managed by the Control4 system. The use of this chapter is completely optional.
This device assists in fulfilling a room-specific music request. To play music, use a system navigation device available to your current room to choose a specific music source or a device. That device may or may not need to make use of this switch.
View Output Assignments
Once you complete the physical and logical setup tasks, you can view or change setup configuration in the Audio
Matrix Switch front display.
When you power up the Audio Matrix Switch, the following
System Status screen appears momentarily.
The System Status screen is then replaced by the
In to Out Assignments screen.
19
Once you make an assignment, the screen displays the assignment. For example, Output 1 is mapped to Input 1.
Manage Outputs
View Output Assignments
To view output assignments:
1.
Ensure your Audio Matrix Switch is powered up and that the In to Out Assignments screen displays in the front display.
2.
On the In to Out Assignments screen, view the current input-to-output assignments.
The screen consists of 16 output zones and any assigned input source. The shaded arrow indicates the Output currently selected.
20
To explore these menu options, press the buttons on the front panel:
` Setup: Displays an output-specific screen. The most recent screen accessed is displayed by default, but you can choose to view a different output’s setting by changing the Output number.
` Network: Displays the Network Configuration screen. From this screen, you can select
Ethernet or Zigbee.
` Display: Displays the Display Configuration
Screen.
Configure an Output
To change output source or settings:
1.
On the Output to Input screen, press the Setup button to view the output settings of the default output screen (which is the last output screen accessed).
From the output screen, you can: (1) change to another output screen; (2) change the output settings on the screen; or (3) toggle to the Input Signal
Sensing screen.
1a. If the output-specific screen you want to view did not display, use the Select Dial to highlight and select the output number and then change it.
1b. (Optional) Change settings for the current output using the supported ranges:
` Input: Displays the number of the currently assigned input source and any label given to the input source. You can change this setting to any available input sources.
21
` Gain: Supported range: Mute and -44 to
+4 dB (default: 0 dB)
` Treble: Supported range: -12 to +12 dB
(default: 0 dB)
` Bass: Supported range: -12 to +12 dB
(default: 0 dB)
` Balance: Supported range: -50 to +50dB
(default: 0 dB)
1c. To toggle to view input signal sensing information, press the Inputs button.
1d. To exit the screen, press the Exit button.
2.
Rotate the Select Dial to highlight a setting.
3.
Press the Select Dial to enter edit mode.
4.
Rotate the dial to change the setting; then press the dial to Save the new setting and exit edit mode or, to exit without saving, use the Cancel button.
5.
Press the Inputs button to go to the Input Signal
Sensing screen, or press the Exit button to return to the Output to Input screen.
Check Signal Status
1.
From the Output to Input screen, press the Setup button, then press the Inputs button to access the
Input Signal Sensing screen.
2.
On the Input Signal Sensing screen, a shaded circle appears by the device connection number of any input device with a signal present.
22
View Network Settings
To view network settings:
1.
Press Network.
2.
From the Network Configuration screen, select
Ethernet or Zigbee.
3.
To return to the Network Configuration screen, press
Back.
Set Front Display Preferences
To set your viewing preferences for the front display:
1.
On the Output to Input screen, press the Display button. The Display Configuration screen displays.
Use the buttons and/or the Select Dial to choose a setting to change: Once you press the Select button
(or press the dial), you enter Edit mode.
2.
In Edit mode, use the buttons or Select Dial to change the highlighted setting then press the OK button (or press the dial) to save the change and exit.
Brightness: Supported range: 0 to 100
Contrast: Supported range: 0 to 100
Backlight Timeout: Supported settings are:
`
OFF (always off)
`
1 to 90 seconds (default is 30 seconds)
`
ON (always on)
Reset Defaults: Restores factory defaults.
23
24
C H A P T E R 4
Regulatory Compliance and Warranty
Regulatory Compliance
This product complies with standards established by the following regulatory bodies:
Federal Communications Commission (FCC)
Industry Canada
Underwriters Laboratories Inc. (UL)
CE
FCC
FCC ID: R33C416S2EB
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
25
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
`
Reorient or relocate the receiving antenna.
`
Increase the separation between the equipment and receiver.
`
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
`
Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modifications not expressly approved by Control4 could void the user’s authority to operate the equipment.
Industry Canada
This Class B digital apparatus complies with Canada ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
Edison Test Lab (ETL)
This product has been tested by ETL and has been found to be in compliance with:
`
UL 60065, Second Edition, “Standard for Audio/Video and Electronic
Equipment”
`
CSA C22.2 No. 60065-03, First Edition: 2006, “Audio, Video and Similar
Electronic Equipment”
26
CE Declaration of Conformity
European Contact Information
Control4 UK Limited
Unit 3, Green Park Business Centre
Sutton-on-the-Forest, York
YO61 IET, United Kingdom
+44 (0) 134781 2300, [email protected]
United States Contact
Information
Control4 Corporation
11734 S. Election Road, Suite 200
Salt Lake City, UT 84020-6432, USA
Tel (801) 523-3100
Product: Audio Matrix Switch (Model # C4-16S2-E-B)
The undersigned hereby declares, on behalf of Control4 Corporation, that the above-referenced product, to which this declaration relates, is in conformity with the provisions of:
`
Council Directive 89/336/EEC (May 3, 1989) on Electromagnetic
Compatibility
`
Council Directive 1999/5/EC (Mar 9, 1999) on Radio & Telecommunication
Terminal Equipment (R&TTE)
`
Council Directive 73/23/EEC (Feb. 19, 1973) on Low Voltage Equipment
Safety
`
Council Directive 93/68/EEC (Jul. 22, 1993) Amending Directives 89/336/
EEC and 73/23/EEC
`
` and has been tested to the requirements of, and shown to be in compliance with, the following requisite standards:
`
EN 300-328 V1.7.1 (2006-10), Electromagnetic Compatibility and Radio
Spectrum Matters (ERM); wide band transmission systems; data transmission equipment operating in the 2.4 GHz ISM band and using wide band modulation techniques.
`
EN 55024:1998 incorporates: EN61000 (4-2, 4-3, 4-4, 4-5, 4-6, 4-8, 4-11 and A1 & A2)
EN 61000-3-2:2005, Limits for harmonic current emissions
EN 61000-3-3:2002, Limitation of voltage fluctuations and flicker in low voltage supply systems
The Technical Construction File required by these Directives is maintained at the corporate headquarters of Control4, Salt Lake City, Utah, U.S.A.
Signed,
Brett Molen—Vice President, Engineering, June 6, 2008
27
Warranty
This device has a limited two (2) year warranty on parts from the date of purchase. Control4 will replace or repair any defective unit. Return unit to the place of purchase for replacement. For any damages incurred, the warranty will never exceed the purchase price of the device. This warranty does not cover installation, removal, or reinstallation cost. The warranty is not valid in cases where damage was incurred due to misuse, abuse, incorrect repair, or improper wiring or installation. It does not cover incidental or consequential damage.
This warranty gives you specific legal rights, and you might also be entitled to other rights that vary from state to state. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages. In these cases, the above mentioned limitations might not apply to you. For complete warranty information, see www.control4.com/warranty.
28
Index
A
About the Audio Matrix Switch
Additional Resources
Audio
Inputs
Outputs
Audio In
Audio Matrix Switch
Back View
Audio In
Audio Out
Ethernet
Power Plug Port
Front View
Buttons
Front Display
Select Dial
Audio Matrix Switch Routing Worksheet
Audio Out
B
Back View
Backlighting
Buttons
C
Cautions
Check Signal Status
Configure an Output
Connect Input and Output Devices
29
Connect to the Network and Power
D
Display
E
Ethernet
,
DHCP
Static IP
F
Features and Benefits
Front Display
Front View
I
Input
Connect Input and Output Devices
M
Manage Outputs
View Output Assignments
Display
Network
Setup
N
Network
Ethernet
Requirements
Settings
Zigbee
Network Configuration
Notes
30
O
Output
Configure
Connect Input and Output Devices
Manage Outputs
View Assignments
P
Plan Your Physical Layout
Power Plug Port
R
Regulatory Compliance
S
Safety Instructions
Select Dial
Set Front Display Preferences
Set Up Logical Connections
Set Up the Audio Matrix Switch
Setup
Source
Source Inputs
Static IP
T
Technical Specifications
Tips
U
Use Audio Matrix Switch
V
View
View Network Setting
31
View Output Assignments
W
Warnings
Warranty
What’s in the Box
Z
Zigbee
32
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce