Wenglor P1EL200 Operating Instructions Manual

Add to My manuals
21 Pages

advertisement

Wenglor P1EL200 Operating Instructions Manual | Manualzz
EN
P1ELxxx
Retro-Reflex Sensor with Light Band
Operating Instructions
Translation of the Original Operating Instruction Subject to change without notice
Available as PDF version only
Version 1.0.0
Status: 28.06.2019
www.wenglor.com
Table of Contents
1. General���������������������������������������������������������������������������������������������������������������������������������� 3
1.1 Information Concerning these Instructions���������������������������������������������������������������������������������������������3
1.2 Explanations of Symbols�������������������������������������������������������������������������������������������������������������������������3
1.3 Limitation of Liability���������������������������������������������������������������������������������������������������������������������������������4
1.4 Copyrights������������������������������������������������������������������������������������������������������������������������������������������������4
2. For Your Safety���������������������������������������������������������������������������������������������������������������������� 5
2.1 Use for Intended Purpose������������������������������������������������������������������������������������������������������������������������5
2.2 Use for Other than the Intended Purpose������������������������������������������������������������������������������������������������5
2.3 Personnel Qualifications��������������������������������������������������������������������������������������������������������������������������6
2.4 Modification of Products��������������������������������������������������������������������������������������������������������������������������6
2.5 General Safety Precautions���������������������������������������������������������������������������������������������������������������������6
2.6 Laser Warnings����������������������������������������������������������������������������������������������������������������������������������������6
2.7 Approvals and protection class���������������������������������������������������������������������������������������������������������������6
3. Technical Data����������������������������������������������������������������������������������������������������������������������� 7
3.1 Switching distance�����������������������������������������������������������������������������������������������������������������������������������8
3.2 Complementary Products������������������������������������������������������������������������������������������������������������������������8
3.3 Housing Dimensions��������������������������������������������������������������������������������������������������������������������������������9
3.4 Control Panel������������������������������������������������������������������������������������������������������������������������������������������10
3.5 Scope of Delivery�����������������������������������������������������������������������������������������������������������������������������������10
4. Transport and Storage�������������������������������������������������������������������������������������������������������� 11
4.1 Transport������������������������������������������������������������������������������������������������������������������������������������������������11
4.2 Storage���������������������������������������������������������������������������������������������������������������������������������������������������11
5. Installation and Electrical Connection������������������������������������������������������������������������������� 12
5.1 Installation����������������������������������������������������������������������������������������������������������������������������������������������12
5.1.1 Reference Setup��������������������������������������������������������������������������������������������������������������������������12
5.1.2 Lateral Reflector Inclination���������������������������������������������������������������������������������������������������������13
5.1.3 Aligning the Reflector������������������������������������������������������������������������������������������������������������������14
5.1.4 Sensor Inclination������������������������������������������������������������������������������������������������������������������������15
5.2 Electrical Connection�����������������������������������������������������������������������������������������������������������������������������17
5.3 Diagnostics���������������������������������������������������������������������������������������������������������������������������������������������17
6. Settings�������������������������������������������������������������������������������������������������������������������������������� 19
6.1 Standard Teach �������������������������������������������������������������������������������������������������������������������������������������19
6.2 Precision Teach – with Stationary (static) Conveyor Belt����������������������������������������������������������������������19
6.3 Precision Teach – with Running (dynamic) Conveyor Belt�������������������������������������������������������������������20
7. Maintenance Instructions��������������������������������������������������������������������������������������������������� 20
8. Proper Disposal������������������������������������������������������������������������������������������������������������������ 20
9. Appendix������������������������������������������������������������������������������������������������������������������������������ 21
9.1 List of Abbreviations�������������������������������������������������������������������������������������������������������������������������������21
9.2 Change Index, Operating Instructions���������������������������������������������������������������������������������������������������21
9.3 EU Declaration of Conformity����������������������������������������������������������������������������������������������������������������21
2
Table of Contents
1. General
1.1 Information Concerning these Instructions
• These instructions apply to the product with ID code P1ELxxx.
• They make it possible to use the product safely and efficiently.
• These instructions are an integral part of the product and must be kept on hand for the entire duration of
its service life.
• Local accident prevention regulations and national work safety regulations must be complied with as well.
• The product is subject to further technical development, and thus the information contained in
these o
­ perating instructions may also be subject to change. The current version can be found at
www.wenglor.com in the product’s separate download area.
NOTE!
The operating instructions must be read carefully before using the product and must be kept
on hand for later reference.
1.2 Explanations of Symbols
• Safety precautions and warnings are emphasized by means of symbols and attention-getting words
• Safe use of the product is only possible if these safety precautions and warnings are adhered to
The safety precautions and warnings are laid out in accordance with the following principle:
Attention-Getting Word!
Type and Source of Danger!
Possible consequences in the event that the hazard is disregarded.
••Measures for averting the hazard.
The meanings of the attention-getting words, as well as the scope of the associated hazards, are listed below.
DANGER!
This word indicates a hazard with a high degree of risk which, if not avoided, results in death
or severe injury.
WARNING!
This word indicates a hazard with a medium degree of risk which, if not avoided, may result
in death or severe injury.
CAUTION!
This word indicates a hazard with a low degree of risk which, if not avoided, may result in
minor or moderate injury.
ATTENTION!
This word draws attention to a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTE!
A note draws attention to useful tips and suggestions, as well as information regarding
efficient, error-free use.
Retro-Reflex Sensor
3
1.3 Limitation of Liability
• The product has been developed in consideration of the current state-of-the-art and applicable standards
and guidelines. Subject to change without notice.
• A valid declaration of conformity can be accessed at www.wenglor.com in the product’s separate
­download area.
• wenglor sensoric elektronische Geräte GmbH (hereinafter referred to as “wenglor”) excludes all liability in
the event of:
• Non-compliance with the instructions
• Use of the product for purposes other than those intended
• Use by untrained personnel
• Use of unapproved replacement parts
• Unapproved modification of products
• These operating instructions do not include any guarantees from wenglor with regard to the described
procedures or specific product characteristics.
• wenglor assumes no liability for printing errors or other inaccuracies contained in these operating
­instructions, unless wenglor was verifiably aware of such errors at the point in time at which the operating
­instructions were prepared.
1.4 Copyrights
• The contents of these instructions are protected by copyright law.
• All rights are reserved by wenglor.
• Commercial reproduction or any other commercial use of the provided content and information, in
­particular graphics and images, is not permitted without previous written consent from wenglor.
4
General
2. For Your Safety
2.1 Use for Intended Purpose
The product is based on the following functional principle:
Retro-reflex sensor with light band
The retro-reflex sensor with light band scans a significantly larger range than a retro-reflex sensor with a
dot-shaped spot. As a result it’s ideally suited for the reliable detection of objects with irregular shapes or
varying sizes, for example polybags. The light barrier’s light band is nearly collimated, making it very precise
and homogenous. The sensor has a very small blind spot and detects objects as of emitter beam overlap of 4
mm within the overall range of detection. It’s compact design permit installation in extremely small spaces, for
example on the side panels of a conveyor system.
This product can be used in the following industry sectors:
• Special machinery manufacturing • Consumer goods industry
• Heavy machinery manufacturing
• Paper industry
• Logistics
• Electronics industry
• Automotive industry
• Glass industry
• Food industry
• Steel industry
• Packaging industry
• Aviation industry
• Pharmaceuticals industry
• Chemicals industry
• Plastics industry
• Alternative energy
• Woodworking industry
• Raw materials extraction
2.2 Use for Other than the Intended Purpose
• Not a safety component in accordance with 2006/42/EC (Machinery Directive).
• The product is not suitable for use in potentially explosive atmospheres.
• The product may only be used with accessories supplied or approved by wenglor, or combined with
approved products. A list of approved accessories and combination products can be accessed at
www.wenglor.com on the product detail page.
DANGER!
Risk of personal injury or property damage in case of use for other than the intended
purpose!
Use for other than the intended purpose may lead to hazardous situations.
• Observe instructions regarding use for intended purpose.
Retro-Reflex Sensor
5
2.3 Personnel Qualifications
• Suitable technical training is a prerequisite.
• In-house electronics training is required.
• Trained personnel must have uninterrupted access to the operating instructions.
DANGER!
Risk of personal injury or property damage in case of incorrect initial start-up and
maintenance!
Personal injury and damage to equipment may occur.
••Adequate training and qualification of personnel.
2.4 Modification of Products
DANGER!
Risk of personal injury or property damage if the product is modified!
Personal injury and damage to equipment may occur. Non-observance may result in loss of
the CE marking and the guarantee may be rendered null and void.
••Modification of the product is impermissible.
2.5 General Safety Precautions
NOTE!
• These instructions are an integral part of the product and must be kept on hand for the
entire duration of its service life.
• In the event of possible changes, the respectively current version of the operating
­instructions can be accessed at www.wenglor.com in the product’s download area.
• Read the operating instructions carefully before using the product.
• Protect the sensor against contamination and mechanical influences.
2.6 Laser Warnings
LASER CLASS 1
EN 60825-1:2014
Laser Class 1 (EN 60825-1)
Applicable standards and safety regulations must be observed.
T = 250 µs, tp = 20 µs, λ = 650 nm , Pp < 200 µW
2.7 Approvals and protection class
RoHS
6
For Your Safety
3. Technical Data
P1EL
100
Optical Data
Range
Light band height
200
300
1600 mm
27 mm
42 mm
Light source
Laser (red)
Wavelength
650 nm
Laser Class (EN 60825-1)
1
Smallest detectable part *
4 mm
Service life (ambient temp. = +25° C)
100000 h
Max. permissible ambient light
10000 Lux
Electrical Data
Supply power
54 mm
12…30 V DC
Current consumption (operating voltage = 24 V)
< 30 mA
Switching frequency
275 Hz
175 Hz
125 Hz
Response time
1,8 ms
2,9 ms
4,0 ms
Temperature range
−30...60 °C
Switching output switching current
< 2,5 V
Switching output residual current
100 mA
Switching output residual current
< 50 µA
Short-circuit protection
Yes
Reverse polarity protected
Yes
Overload-proof
Yes
Lockable
Yes
Protection class
Mechanical Data
Setting method
III
Teach-in
Housing material
Degree of protection
Plastic
IP67 / IP68
Lens cover
PMMA
Output function
PNP NO
Connection
M12×1
Connection Diagram No.
Suitable Mounting Technology No.
150
2
* The smallest detectable part depends on the utilized teach-in mode and alignment to the reflector:
Teach-in for interference-free detection: 5 mm
Teach-in for precise detection: 4 mm
Retro-Reflex Sensor
7
3.1 Switching distance
Achievable switching distance depends on the utilized reflector. Depending on the utilized sensor type, types
Z90R007 through Z90R009 serve as reference reflectors. Other reflectors can also be used, which are shown
in the following table along with their corresponding ranges.
Reflector
ZRDF03K01
ZRDF10K01
Z90R004
Z90R005
Z90R007
Z90R008
Z90R009
Range
0,40…1,60 m
0,40…1,60 m
0,40…1,60 m
0,40…1,60 m
0,40…1,60 m
0,40…1,60 m
0,40…1,60 m
Sensor
P1EL100
P1EL200
P1EL300
Reference Reflector
Z90R007
Z90R008
Z90R009
3.2 Complementary Products
wenglor can provide you with suitable connection technology for your product.
Suitable connection technology no.
2
S02
PNP-NPN converter BG7V1P-N-2M
8
Technical Data
3.3 Housing Dimensions
P1EL100
P1EL200
Retro-Reflex Sensor
9
P1EL300
1 = emitter diode
2 = receiver diode
M3 screw = 0.5 Nm
Dimensions specified in mm (1 mm = 0.03937”)
3.4 Control Panel
1E1
68
30
06
06 = teach-in key
30 = switching status indicator / contamination warning
68 = supply power indicator
3.5 Scope of Delivery
• Sensor
• Safety precautions
• Spacer sleeves Z1PE002
10
Technical Data
4. Transport and Storage
4.1 Transport
Upon receipt of shipment, the goods must be inspected for damage in transit. In the case of damage, conditionally accept the package and notify the manufacturer of the damage. Then return the device, making
reference to damage in transit.
4.2 Storage
The following points must be taken into condition with regard to storage:
• Do not store the product outdoors.
• Store the product in a dry, dust-free place.
• Protect the product against mechanical impacts.
• Protect the product against exposure to direct sunlight.
ATTENTION!
Risk of property damage in case of improper storage!
The product may be damaged.
• Storage instructions must be complied with.
Retro-Reflex Sensor
11
5. Installation and Electrical Connection
5.1 Installation
• Protect the product from contamination during installation.
• Observe all applicable electrical and mechanical regulations, standards, and safety rules.
• Protect the product against mechanical influences.
• Make sure that the sensor is mounted in a mechanically secure fashion.
• Specified torque values must be complied with (see Technical Data on page 10).
The following installation instructions must be observed in order to assure that the sensor can function correctly:
5.1.1 Reference Setup
All sensor values are based on a reference setup which demonstrates the following characteristics:
••The P1ELxxx sensor and the conveyor belt’s zero level (conveyor level) are arranged at a right angle to
each other.
••The conveyor level doesn’t fluctuate at all.
••The sensor is mounted such that the bottom edge of the emitted light band is at the conveyor level.
••The sensor’s light band is parallel to the conveyor level (max. tolerance: +0/–2 mm).
••The utilized reflector is inclined 2° and captures the entire light band.
12
Installation and Electrical Connection
5.1.2 Lateral Reflector Inclination
Z90R007 through Z90R009 reflectors, which are laid out for the P1ELxxx, are inclined 2° due to their format
and can be mounted without lateral tilting.
The reflectors listed in section 3.1, “Switching Distance”, are not inclined and must therefore be mounted at
an inclined angle of 2° (±0.5°). The direction in which the reflector is tilted depends on the installation situation and must correspond exactly to the illustration.
Insulation situation 1
Insulation situation 2
Retro-Reflex Sensor
13
5.1.3 Aligning the Reflector
Z90R007 through Z90R009 reflectors must be mounted as shown in the following illustration. Correct
inclination of the surface of the reflector relative to the sensor is described in section „5.1.2 Lateral Reflector
Inclination“ on page 13.
14
Installation and Electrical Connection
5.1.4 Sensor Inclination
Deviation of the top edge of the light band should not exceed +0 to –2 mm of downward sloping to the conveyor plane in order to permit detection of the smallest object. Deviation amounting to more than this value
leads to poor detection of small or flat objects.
Ideal Alignment
Incorrect Alignment
Excessive tilting of the sensor (> 2 mm downward sloping of the top edge of the light band) towards the
conveyor plane results in an area with reduced detection of small objects which are in close proximity to the
sensor.
Retro-Reflex Sensor
15
Tilting the sensor away from the conveyor plane results in an area with reduced detection of small objects
which are far away from the sensor, i.e. close to the reflector.
NOTE!
Ideal alignment can be easily determined by means of the band of light above the conveyor
belt. First of all, height is determined from the conveyor belt to the uppermost point of the
band of light directly on the sensor. Afterwards, height is determined from the conveyor belt
to the uppermost point of the band of light on the reflector. Alignment is ideal when these
two distances are identical.
wenglor recommends a sensor adjustment range with parallel upper light-band edge, or
maximum downward sloping of the upper edge of the light band amounting to 2 mm within
the corresponding working range.
ATTENTION!
Risk of property damage in case of improper installation!
The product may be damaged.
• Installation instructions must be complied with.
CAUTION!
Risk of personal injury or property damage during installation!
Personal injury and damage to the product may occur.
• A safe installation environment must be assured.
16
Installation and Electrical Connection
5.2 Electrical Connection
150
Legend
PT
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output
Switching Output
Contamination/Error Output
Contamination/Error Output
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
(NO)
(NC)
(NO)
(NC)
Power over Ethernet
Safety Input
Safety Output
Signal Output
Ethernet Gigabit bidirect. data line (A-D)
Encoder 0-pulse 0-0 (TTL)
Platinum measuring resistor
not connected
Test Input
Test Input inverted
Trigger Input
Ground for the Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Ground for the Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Encoder A/A (TTL)
Encoder B/B (TTL)
Encoder A
Encoder B
Digital output MIN
Digital output MAX
Digital output OK
Synchronization In
Synchronization OUT
Brightness output
Maintenance
reserved
Wire Colors according to IEC 60757
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green/Yellow
DANGER!
Risk of personal injury or property damage due to electric current!
Voltage conducting parts may cause personal injury or damage to equipment.
••The electric device may only be connected by appropriately qualified personnel.
5.3 Diagnostics
Causes for Triggering the Contamination Warning (blinking LED):
Display LED
Diagnosis/Cause
Contamination
Continuous blinking
Aged emitter diode
at approx. 2.5 Hz
Unreliable working range
Continuous blinking Short-circuit
at approx. 5 Hz
Hardware error
Retro-Reflex Sensor
Elimination
Carefully clean the optic cover and the reflector with a
cloth.
Replace the sensor.
Check distance to the sensor (see “3.1 Switching distance” on page 8).
Check electrical wiring and eliminate the short-circuit.
Replace the sensor.
17
Contamination Warning Flowcharts
Retro Reflective Barrier
no contamination
Reflector
Object
t
not detected
on
Switching Status Indicator
Reflector
Object
Sensor
Object
Reflector
Sensor
detected
Object
Sensor
not detected
off
on
beginning contamination
Reflector
Object
Switching Status Indicator
Reflector
Object
Sensor
Object
Reflector
not detected
Sensor
detected
off
blinking
Object
Sensor
not detected
blinking
advanced contamination
Reflector
Object
Object
Sensor
Object
Switching Status Indicator
Reflector
not detected
off
Sensor
not detected
off
Reflector
Object
Sensor
not detected
off
Required action in case of fault:
NOTE!
• Shut down the machine.
• Analyze and eliminate the cause of error with the help of the diagnostics information.
• If the error cannot be eliminated, please contact wenglor’s support department.
• Do not operate in case of indeterminate malfunctioning.
• The machine must be shut down if the error cannot be unequivocally clarified or reliably
eliminated.
DANGER!
Risk of personal injury or property damage in case of non-compliance!
The system’s safety function is disabled. Personal injury and damage to equipment.
••Required action as specified in case of fault.
18
Installation and Electrical Connection
6. Settings
NOTE!
It takes three minutes for the sensor to warm up. In order to assure interference-free operation, teach-in should not be conducted until after the warm-up phase.
6.1 Standard Teach
The sensor is taught in such that it demonstrates stable switching performance despite interference such
as vibration. In this mode, the smallest part which can be detected is somewhat larger than in the precise
detection mode.
• Install the sensor in accordance with the mounting instructions.
• Align the sensor to the reflector.
• Press and hold the teach-in key until switching status indicator A1 starts blinking slowly (2 Hz) after two
seconds.
• Release the teach-in key.
• The switching threshold is taught in and the LED for A1 blinks twice in order to confirm successful
teach-in.
6.2 Precision Teach – with Stationary Conveyor Belt
The sensor is taught in such that the detection of very small parts is possible. With the conveyor belt at a
standstill, the sensor is set to a signal analysis phase which lasts for 10 seconds. The sensor’s receive signals
are analyzed during this time, on the basis of which the switching threshold is calculated.
• Install the sensor in accordance with the mounting instructions.
• Align the sensor to the reflector.
• Press and hold the teach-in key until switching status indicator A1 starts blinking rapidly (4 Hz) after five
seconds.
• Release the teach-in key.
• Recording is started during which the LED continues to blink at a rate of 4 Hz.
• The calculated switching threshold is taught in and the LED for A1 blinks twice in order to confirm successful teach-in. If teach-in has not been successful, LED A1 blinks 4 times. If this is the case, the procedure must be repeated.
Retro-Reflex Sensor
19
6.3 Dynamic Teach – with Running Conveyor Belt
The sensor is taught in such that, depending on the application, minimal thresholds can be set in order to
detect smallest possible parts by means of this process. With running conveyor belt, the sensor is set to a
signal analysis phase which lasts for 10 seconds. The application-specific receive signals are analyzed by the
sensor during this time, on the basis of which the switching threshold is calculated. And thus application-specific receive signals do not result in erroneous sensors switching.
• Install the sensor in accordance with the mounting instructions.
• Align the sensor to the reflector.
• Press and hold the teach-in key until switching status indicator A1 starts blinking rapidly (4 Hz) after five
seconds.
• Release the teach-in key.
• Recording is started during which the LED continues to blink at a rate of 4 Hz.
• The sensor analyzes the receive signals for 10 seconds, on the basis of which it calculates a precise
switching threshold that’s matched to the application.
• The calculated switching threshold is taught in and the LED for A1 blinks twice in order to confirm successful teach-in. If teach-in has not been successful, LED A1 blinks 4 times. If this is the case, the procedure must be repeated.
NOTE!
If the sensor is used at a very small distance above a conveyor belt, it’s advisable to activate the belt during the recording phase. Height fluctuations, impacts, belt seams etc. are
analyzed as a result and made use of when calculating the switching threshold. Erroneous
switching due to the conveyor belt can be avoided in this way.
7. Maintenance Instructions
NOTE!
• This wenglor sensor is maintenance-free.
• Cleaning and inspection of the plug connections at regular intervals are advisable.
• Do not clean the sensor with solvents or cleansers which could damage the product.
• The product must be protected against contamination during initial start-up.
8. Proper Disposal
wenglor sensoric GmbH does not accept the return of unusable or irreparable products. Respectively valid
national waste disposal regulations apply to product disposal.
20
Maintenance Instructions
9. Appendix
9.1 List of Abbreviations
Abbreviation
Tu
Meaning
Ambient temperature
Ub
MTTFd
Supply voltage
Mean Time to Dangerous Failure
9.2 Change Index, Operating Instructions
Version
1.0.0
Date
06.06.19
Description/Change
Initial version of the operating instructions
9.3 EU Declaration of Conformity
The EU declaration of conformity can be found on our website at www.wenglor.com in the product’s
­download area.
Retro-Reflex Sensor
21

advertisement

Related manuals