Kemppi Pro Evolution 3200, 4200, 5200 Owner's Manual
विज्ञापन
विज्ञापन
1913130E
0617
Kemppi pRO eVOLUTiON
3200, 4200, 5200
Kemppi pRO eVOLUTiON
3200 mVU, 4200 mVU, 5200 mVU
contents
1.
2. preface ........................................................................................................................3
1.1.
1.2.
1.3.
1.4.
InstallatIon ...............................................................................................................7
2.1.
Introduction .......................................................................................................................3
Product introduction ..........................................................................................................3
1.2.1. Operation control and connectors ................................................................................... 4
Accessories .......................................................................................................................5
1.3.1.
1.3.2.
1.3.3.
Remote control devices ................................................................................................... 5
Control panels ................................................................................................................. 5
Cables ............................................................................................................................. 6
Operation safety ................................................................................................................6
Siting the machine and mounting the control panels PL and PX ......................................7
2.2.1.
2.2.2.
Connection to the mains supply ...................................................................................... 7
Welding and earth cables ................................................................................................ 8
3.
4.
5.
6. operatIon control swItches and potentIometers and theIr use ..... 8
3.1.
3.2.
3.3.
3.4.
4.1.
Main switch I/O ..................................................................................................................8
Pilot lamps .........................................................................................................................9
Local or remote control of welding current ........................................................................9
Operation of cooling fan ....................................................................................................9
accessorIes ...............................................................................................................9
PL and PX control panels’ operation in MMA welding .......................................................9
4.1.1.
4.1.2.
4.1.3.
4.1.4.
Control for MMA welding dynamics (PL, PX) .................................................................. 9
Control of ignition pulse current (PX) ............................................................................ 10
Meter display (PL, PX) .................................................................................................. 10
Operation mede selection (PX) ..................................................................................... 10 coolIng unIt supply .............................................................................................. 11 maIntenance ............................................................................................................ 11
6.1.
6.2.
6.3.
Cables ............................................................................................................................. 11
Power source ..................................................................................................................12
Regular maintenance ......................................................................................................12
operatIon dIsturbances ....................................................................................12
7.
8.
9.
7.1.
7.2.
7.3.
7.4.
7.5.
Operation of the overload protection ...............................................................................12
Control fuses ...................................................................................................................12
Under- and overvoltages in the mains supply .................................................................13
Loss of a phase in the mains supply ...............................................................................13
Disposal of the machine ..................................................................................................13
orderIng numbers ................................................................................................13
technIcal data .......................................................................................................14
10. terms of guarantee .............................................................................................15
– Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
1. preface
1.1. IntroductIon
Congratulations on having purchased this product. Properly installed Kemppi products should prove to be productive machines requiring maintenance at only regular intervals. This manual is arranged to give you a good understanding of the equipment and its safe operation. It also contains maintenance information and technical specifications. Read this manual from front to back before installing, operating or maintaining the equipment for the first time. For further information on Kemppi products please contact us or your nearest Kemppi distributor.
The specifications and designs presented in this manual are subject to change without prior notice.
In this document, for danger to life or injury the following symbol is used:
Read the warning texts carefully and follow the instructions. Please also study the Operation safety instructions and respect them when installing, operating and servicing the machine.
1.2. product IntroductIon
Kemppi Pro Evolution 3200, 4200 and 5200 are multi-operator power sources designed for demanding professional use. They are suitable for MMA/MIG and pulsed MIG as well as for
TIG welding in DC. Kemppi Pro Evolution can be used as power source with a welding auto mate or robot.
Power control of Kemppi Pro Evolution power source has been realized with at approx. 20 kHz frequency IGBT transistors operating and control unit with microprosessor.
Kemppi Pro machines can be seen in operating instructions for each unit. Mounting intructions for control panels PX and PL are in their packages.
This manual handles installation and use of Kemppi Pro Evolution power sources.
This equipment’s electromagnetic compatibility (EMC) is designed for use in an industrial environment. Class A equipment is not intended for use in residential location where the electrical power is provided by the public low-voltage supply system.
© Kemppi oy Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 – 3
1.2.1. Operation control and connectors
H12
H11
S11
01
F11
X16
F12
pro evolutIon
F11 Fuse for connetion for control table 6,3 A delayed
H11 Signal lamp I/O
H12 Warning lamp for thermal protection
S11 Main switch I/O
X11, Welding connection
X12 parallel
X13 Earth connection
X14, Connection for control cable
X15
01 Inlet of mains cable parallel
02 Inspection cover for control panel PL, PX Accessories
X16 Socket outlet
F12 Fuse for socket outlet
Fuse 230 V, 250 VA
1,0 A delayed
S11
H12
H11
01
F11
pro evolutIon mvu
4 – Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
X11
X12
X13
X15
X14
X11
X12
X13
X15
X14
1.3. accessorIes
1.3.1. Remote control devices
R10 6185409
R61
Control of MMA/TIG welding current (R61), reference scale 1 … 10.
R20 6185419
R63 R61
S31
S32
MIG-MAG remote control device with controls for wire feed (R63) and voltage (R61), memory scales 1 … 10.
You can use control device also for control of MMA current from potentiometer R63.
1.3.2. Control panels
P21 P22 P23 R22
P31
S33
R21
P32 P33 H31 H32
S34 S35
S21
S36
S37
PL panel 6185801
P21 Current meter set value / welding current
P22 Voltage meter open circuit / terminal voltage
P23 Display for adjustment value of MMA welding dynamics -9 … 0 …+9
R21 Adjustment of welding current
R22 Adjustment of MMA welding dynamics
S21 Selection for local / remote control local / MIG/TIG / remote control
PX panel 6185802
H31 Signal lamp for voltage display
H32 Signal lamp for display of adjustment status
P31 Current meter / set value / welding current
P32 Voltage meter / open circuit / terminal voltage
P33 Display for adjustment value of MMA welding dynamics and start current -9 … 0 …+9
S31, Adjustment of welding current + / -
S32
S33 Selection for local / remote control local / MIG/TIG / remote control
S34 Selection for characteristics
Point to point welding / normal welding / carbon arc gouging
S35 Selection of property to be adjusted
MMA welding dynamics / start current
S36, Adjustment for MMA welding dynamics
S37 and start current + / -
RECALL STD = resetting of factory set up (=0)
© Kemppi oy Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 – 5
1.3.3. Cables
Pro Evolution 3200
Pro Evolution 4200
Pro Evolution 5200
Pro Evolution 3200 MVU
Pro Evolution 4200 MVU
Pro Evolution 5200 MVU
16d Extension cable for remote control
20 Earth cable
21 MMA welding cable
R10, Remote control devices, see also page 5
R20
1.4. operatIon safety
Please study these Operation safety instructions and respect them when installing, operating and servicing the machine.
Welding arc and spatters
Welding arc hurts unprotected eyes. Be careful also with reflecting arc flash. Welding arc and spatter burn unprotected skin. Use safety gloves and protective clothing.
Danger for fire or explosion
Pay attention to fire safety regulations. Remove flammable or explosive materials from welding place. Always ensure that you have sufficent fire fighting equipment available where you are welding. Be prepared for hazards in special welding jobs, eg. for the danger of fire or explosion when welding container type work pieces. Note! Fire can break out from sparks even several hours after the welding work has been finished!
Mains voltage
Never take welding machine inside a work piece (eg. container or truck). Do not place welding machine on a wet surface. Always check cables before operating the machine. Change damaged cables without delay. Damaged cables may cause an injury or set out a fire. Connection cable must not be crushed, it must not touch sharp edges or hot work pieces.
Welding power circuit
Isolate yourself by using proper protective clothing, do not wear wet clothing. Never work on a wet surface or use defect cables. Do not put the MIG-gun or welding cables on welding machine or on other electric equipment. Do not press the MIG-gun switch, if the gun is not directed towards a work piece.
Welding fumes
Take care that there is sufficient ventilation during welding. Take special safety precautions when welding metals which contain lead, cadmium, zinc, mercury or beryllium.
6 – Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
2. InstallatIon
2.1. sItIng the machIne
Site the machine on a stationary, horizontal, dry base in a position that does NOT allow dust, dirt or metal particles to enter the machines cooling air flow.
60 0 max. 15 0
- Preferably site the machine somewhat higher above the
floor level.
- Ensure that the front as well as the rear of the machine
there is at least 20 cm free distance to allow good
circulation of the cooling air through the machine.
- Protect the machine against heavy rain and in hot
circumstances against direct sunshine. Ensure the free
circulation of the cooling air.
rain water
Degree of protection of machine IP23 allows at its maximum the water spray coming in 60º angle to hit machine’s outer covering.
See to that the machine is positioned away from the line of particle spray, created by grinding tools etc.
2.2. mountIng the control panels pl and pX
Mounting of panel should only be carried out by competent electrician.
Attention! Disconnect plug of machine from mains socket and wait for approx. 2 min before removing cover plate.
- On the front face of machine there is a cover plate where the control panel is mounted.
Without a panel the machine is controlled either from remote control unit or Promig
or Protig unit.
- Mount PL or PX panel according to mounting instructions delivered with them.
2.2.1. Connection to the mains supply
Kemppi Pro Evolution power sources are delivered equipped with 5 m mains cable without plug.
If local electricity regulations of operating country are stating otherwise, the mains cable should be replaced in conformity with the local regulations.
Connection of the mains cable, mounting and change of the plug should only be carried out by a competent electrician.
Remove the machine’s right side plate to enable the mounting of a mains cable.
© Kemppi oy Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 – 7
If changing the mains cable take into consideration the following:
The cable is entered into the machine through the inlet ring on the rear panel of the machine and fastened with a cable clamp (05). The phase conductors of the cable are coupled to connectors
L1, L2 and L3. The earth protection coloured green-yellow is coupled to connector
If you are using 5-lead cable, you must connect neutral conductor with terminal N.
05
Sizes of the mains cables and fuse ratings for the machine at 100% duty cycle are specified in the table below:
Rated voltage Mains voltage range Fuses, slow-blow
Pro Evolution 3200
Pro Evolution 4200
Pro Evolution 5200
400 V 3~
400 V 3~
400 V 3~
360 V… 440 V
360 V… 440 V
360 V… 440 V
25 A
35 A
35 A
Pro Evolution 3200 MVU 400 V 3~ 230 V 3~ 360 V… 440 V 200 V… 260 V 35 A
Pro Evolution 4200 MVU 400 V 3~ 230 V 3~ 360 V… 440 V 200 V… 260 V 50 A
Pro Evolution 5200 MVU 400 V 3~ 230 V 3~ 360 V… 440 V 200 V… 260 V 60 A
Connection cable *) mm 2
4 x 6.0 S
4 x 6.0 S
4 x 6.0 S
4 x 6.0 S
4 x10 S
4 x 16 S
*) In cables of S type there is a protective grounding conductor coloured green-yellow.
2.2.2. Welding and earth cables
Recommended copper cables with cross-sectional area are as follows:
Kemppi Pro Evolution 3200 50 ... 70 mm 2
Kemppi Pro Evolution 4200 70 ... 90 mm 2
Kemppi Pro Evolution 5200 70 ... 90 mm 2
In enclosed table are shown typical load capacities of rubber insulated copper cables, when ambient temperature is 25 ºC and lead temperature is 85 ºC.
CABLE DUTY CYCLE ED VOLTAGE LOSS / 10m
...........................100% .........60% ........... 30%
50 mm 2 ..............285 A .........370 A ......... 520 A ...........0,35 V / 100 A
70 mm 2 ..............355 A .........460 A ......... 650 A ...........0,25 V / 100 A
95 mm 2 ..............430 A .........560 A ......... 790 A ...........0,18 V / 100 A
Do not overload welding cables due to voltage losses and heating.
Fasten the earth clamp of the return current cable carefully, preferably direct onto the piece to be welded. The contact surface of the earth clamp should always be as large as possible.
Clean the fastening surface from paint and rust.
3. operatIon control swItches and potentIometers and theIr use
3.1. maIn swItch I/o
When you turn the switch into I-position, pilot lamp H11 on the front face is illuminated and the machine is ready for use.
Always turn the machine on and off with the mains switch, never use the mains plugs as a switch.
– Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
I
2
3.2. pIlot lamps
The pilot lamps of the machine report the electric operation:
The green pilot lamp H11 when lit indicates that the machine is on and ready for use and it is connected to the mains supply with the main switch in the I-position.
H12 indicates when lit that the thermal protection of the machine has been activated due to over heating. The cooling fan will continue to run and cool the machine down and when the lamp is off the machine ia ready to weld.
3.3. local or remote control of weldIng current
You can control welding current either from local controls of PX or PL control panel, or from remote control unit which is connected to remote control connector X14 or X15, or from Promig or Protig unit.
Selector switch of control panel has to be in a position corresponding to control mode: local control / MIG/TIG / remote control unit.
Suitable remote control units R10 and R20, see page 5.
At MIG and TIG welding, current control is made according to operation instruction of control ling MIG or TIG unit.
3.4. operatIon of coolIng fan
In Kemppi Pro Evolution 3200 there is one and in 4200 and 5200 there are two simultaneously operating fans.
- The fan is started for a moment when main switch is placed into postion I.
- The fan will start during welding as the machine heats up and it will run for 1 to 10 minutes
after the welding has stopped.
- On no-load fan is started in intervals of approx. half an hour for minute’s time.
4. accessorIes
4.1. pl and pX control panels’ operatIon In mma weldIng
4.1.1. Control for MMA welding dynamics (PL, PX)
With control for electrode dynamics you can influence arc behaviour in different kinds of opera tion situations.
When arc is roughened, blowing is increasing and at the same time also spatter.
Soft arc. Object to reduce amount of spatter in welding at the upper end of recommen ded currents for electrode.
Factory setup (PX). Normal setting for all electrode types.
Rough arc. Object e.g. cellulose covered electrodes and thin stainless electrode in welding at the lower end of the recommended curents for electrode.
9
0
-9
0 =
Roughening
Factory setup
Softening
© Kemppi oy t
Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 –
I
2
4.1.2. Control of ignition pulse current (PX)
Display 0 corresponds to factory set up of ignition pulse. Number of ignition pulsesd epends on electrode type and diameter which are used. Ignition pulse changes with set value of welding current in such a way that at low values ignition pulse is low and short and at high values it is higher and longer.
Low, short ignition pulse. Object e.g. small stainless electrodes.
Factory set up. Object e.g. basic electrodes.
High, long ignition pulse. Object e.g. high efficiency electrodes.
9
0
-9
0 = factory set up
4.1.3. Meter display (PL, PX)
t
Voltage meter shows machine’s terminal voltage which is voltage between connectors X11/X12 and X13.
Accurancy of current true value in respect to real value is ±2,5 %, ±2 A.
Accurancy of voltage true value in respect to real value is ±2,5 %, ±0,2 V.
Depending on welding cable legth and copper cross section, real arc voltage and meter display might differ main volts from each other. Error will incease when current is growing. See table in paragraph ”Welding and earth cables”, page 8.
In current measurement the same error won’t appear.
4.1.4. Operation mede selection (PX)
Normal MMA welding
U
2
In normal MMA welding there are constant current characteristics in the machine. The machine is trying to keep welding current value regardless of arc length changes.
U
2
=20V+0,04xI
2 norm line max.
statically constant current
I
2
10 – Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
U
2
Point to point welding
Point to point welding is necessary then when the seam to be welded does not withstand heat of continuous arc and welding has to be carried out by interrupting arc. The reason is usually thin materials or variable fittings.
The machine has characteristic curve which makes interrupting of arc easier when electrode is drawn further from seam.
U
2
=20V+0,04xI
2
U
U
2
I
2 statically constant current U is limited below max. voltage of machine
Carbon arc gouging
In carbon arc gouging there are dynamic constant voltage curves. If the tip gouging carbon makes a short circuit, the power source will make an strong increase to the current, the short circuit ends rapidly and the arc will remain or reignite easier.
dynamically constant voltage
I
2
5. coolIng unIt supply
1~230 v / 250 va
Kemppi Pro Evolution 4200 and 5200 power sources have as stardard a by productive earthed outlet X16 isolated safety transformer. Procool cooling unit is connected to this outlet.
6. maIntenance
The amount of use and the working environment shoud be taken into consideration when planning the frequency of maintenance of the machine. Careful use and preventive maintenance will help to ensure trouble-free operation.
6.1. cables
Check the condition of welding and connection cables daily. Do not use damaged cables.
Make sure that the mains cables in use are safe and according to laid down regulations.
The repair and mounting of a mains connection cables should be carried out only by an authorized electrician.
© Kemppi oy Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 – 11
6.2. power source
Note! Disconnect the plug of the machine from the mains socket and wait approx. 2 minutes (capacitor charge) before removing the cover plate.
Check at least every half year:
- Electric connectors of the machine - clean the oxidized parts and tighten the loosened ones.
- Note! You must know correction tension torques before starting the reparation of the joints.
- Clean the inner parts of the machine from dust and dirt e.g. with a soft brush and vacuum
cleaner. Also clean the ventilation net behind the front grate.
- Do not use compressed air, there is a risk that dirt is packed even more tightly into gaps
of cooling profiles.
- Do not use pressure washing device.
- Only authorized electrician shall carry out repairs to the machines.
6.3. regular maIntenance
Kemppi Service Workshops make regular maintenance according to agreement.
The major points in the maintenace procedure are listed as follows:
- Cleaning of the machine
- Checking and maintenance of the welding tools
- Checking of connectors, switches and potentiometers
- Checking of electric connections
- Meter checking
- Checking of mains cable and plug
- Damaged parts or parts in bad connection are replaced by new ones
- Maintenace testing. Operation and performance values of the machine are checked, and
adjusted when necessary by means of test equipment.
7. operatIon dIsturbances
In case of problems contact the Kemppi works in Lahti, Finland, or your local Kemppi dealer.
Check the maintenace objects before the machine is sent to the Service Workshop.
7.1. operatIon of the overload protectIon
Yellow pilot lamp H12 of thermal protection is lit when thermostat has operated due to overheating of machine.
The thermostat of machine will operate, if machine is continuously loaded over rated values or cooing air circulation is blocked.
Cooling fan cools down the machine and when the pilot lamp is not lit the machine is automati cally ready for welding.
7.2. control fuses
Fuse F11, 6,3 A delayed, on the rear wall of machine is as protection for connection of auxiliary devices X14-15.
Voltage unit for auxiliary devices (1~230 V/240 VA) has a fuse of its own F12 1,0 A delayed.
Use same type and rating of fuse which is marked beside the fuse adapter.
Damage caused by a wrong type fuse is not covered by the guarantee.
1 – Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
7.3. under- and overvoltages In the maIns supply
Primary circuits of machine are protected against sudden, transient overvoltages.
Machine is designed to withstand 3 x 440 V voltage continiously (see technical data). See to it that voltage is kept within admissble limits especially when mains supply is taken e.g. from combusition engine generator.
If the mains has undervoltage (under approx. 300 V), machine control stops to operate automa tically.
7.4. loss of a phase In the maIns supply
Loss of a phase causes noticeable poorer welding properties than normally or the machine doesn’t get started at all. Loss of a phase can be due to following:
- blowing of mains supply fuse
- defective mains cable
- bad connection of mains connection cable on terminal block or plug of machine
7.5. dIsposal of the machIne
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment that has reached the end of its life must be collected separately and returned to an environmentally compatible recycling facility. As the owner of the equipment, you should get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human health!
8. orderIng numbers
Kemppi Pro Evolution 3200
Kemppi Pro Evolution 4200
Kemppi Pro Evolution 5200
Kemppi Pro Evolution 3200 MVU
Kemppi Pro Evolution 4200 MVU
Kemppi Pro Evolution 5200 MVU
Return current cable
Return current cable
5 m - 50 mm 2
5 m - 70 mm 2
Cable for MMA welding
Cable for MMA welding
PL
PX
5 m - 50 mm 2
5 m - 70 mm 2
R10
R20
Remote controlled interconnecting cable 10 m
T10
T120
P40
P40L
P30W
© Kemppi oy
6131320
6131420
6131520
613132003
613142003
613152003
6184511
6184711
6184501
6184701
6185801
6185802
6185409
6185419
6185481
6185231
6185252
6185264
6185264L
6185262
Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 – 13
9. technIcal data
Mains voltage
3~50/60 Hz
Pro Evolution 3200
400 V -15%...+20%
Voltage supply for cooling unit
PROCOOL 10 1~, 230 V / 250 VA
X 16 fuse 1,0 A delayed
Pro Evolution 4200
400 V -15%...+20%
Rated power
80 % ED
100 % ED
Connection cable/ fuse delayed
Max. welding voltage 40 0 C
Extemal dimensions length width height
Weight
Voltage supply for auxiliary devices
X 14, X 15
320 A / 13,3 kVA
4 x 6 S - 5 m / 25 A
530 mm
230 mm
520 mm
37 kg
50 V DC fuse 6,3 A delayed
420 A / 19,7 kVA
400 A / 18,6 kVA
4 x 6S - 5 m /35 A
520 A / 26,6 kVA
440 A / 20,0 kVA
4 x 6S - 5 m / 35 A
70 % ED
80 % ED
100 % ED
Welding current range
MMA
TIG
MIG
320 A / 32,8 V
Max. welding voltage 20 0 C
100 % ED 320 A / 32,8 V
10 A ... 320 A
5 A ... 320 A
12 V ... 37 V
Max. welding voltage
Open circuit voltage
Open circuit power
Efficiency at nominal values
46 V / 300 A appr. 65 V
< 75 W appr. 85 %
Power factor at nominal values
Storage temperature range
Operating temperature range
Temperature class
Degree of protection appr. 0,93
-40 ... +60
-20 ... +40
H (180
IP 23 C
0
0
0
C
C
C) / B (130 0
420 A / 36,8 V
400 A / 36 V
420 A / 36,8 V
10 A ... 420 A
5 A ... 420 A
12 V ... 39 V
46 V / 400 A appr. 65 V
< 75 W appr. 85 % appr. 0,93
-40 ... +60 0 C
-20 ... +40 0 C
C) H (180
IP 23 C
0 C) / B (130 0
520 A / 40,0 V
440 A / 37,6 V
480 A / 39,6 V
10 A ... 520 A
5 A ... 520 A
12 V ... 42 V
50 V / 500 A appr. 65 V
< 75 W appr. 85 % appr. 0,93
-40 ... +60
C) H (180
IP 23 C
0
0 C
-20 ... +40 0 C
C) / B (130 0 C)
530 mm
230 mm
520 mm
41 kg
50 V DC fuse 6,3 A delayed
530 mm
230 mm
520 mm
48 kg
50 V DC fuse 6,3 A delayed
1~, 230 V / 250 VA fuse 1,0 A delayed
Pro Evolution 5200
400 V -15%...+20%
1~, 230 V / 250 VA fuse 1,0 A delayed
14 – Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
9. technIcal data
Mains voltage
3~50/60 Hz
Rated power
80 % ED
100 % ED
Connection cable/ fuse delayed
Pro Evolution 3200 MVU Pro Evolution 4200 MVU Pro Evolution 5200 MVU
400 V -15%...+20%
230 V -10%...+10%
320 A / 13,3 kVA
4 x 6 S - 5 m / 35 A
Max. welding voltage 40 0 C
70 % ED
80 % ED
100 % ED 320 A / 32,8 V
Max. welding voltage 20 0 C
100 % ED 320 A / 32,8 V
Welding current range
MMA
TIG
MIG
10 A ... 320 A
5 A ... 320 A
12 V ... 37 V
Max. welding voltage
Open circuit voltage
Open circuit power appr. 65 V
< 75 W
400 V -15%...+20%
230 V -10%...+10%
420 A / 19,7 kVA
400 A / 18,6 kVA
4 x 10S - 5 m / 50 A
420 A / 36,8 V
400 A / 36 V
420 A / 36,8 V
10 A ... 420 A
5 A ... 420 A
12 V ... 39 V
46 V / 300 A appr. 65 V
< 75 W
400 V -15%...+20%
230 V -10%...+10%
520 A / 26,6 kVA
440 A / 20,0 kVA
520 A / 40,0 V
440 A / 37,6 V
10 A ... 520 A
5 A ... 520 A
12 V ... 42 V
46 V / 400 A 50 V / 500 A appr. 65 V
< 75 W
4 x 16S - 5 m / 63 A
480 A / 39,6 V
Efficiency at nominal values
Power factor at nominal values
Storage temperature range
Operating temperature range
Temperature class
Degree of protection
Extemal dimensions
Weight length width height appr. 85 % appr. 0,93
-40 ... +60
-20 ... +40
H (180
IP 23 C
0
530 mm
230 mm
630 mm
45 kg
0
0
C
C
C) / B (130
Voltage supply for auxiliary devices 50 V DC
X 14, X 15 fuse 6,3 A delayed
Voltage supply for cooling unit
PROCOOL 10 1~, 230 V / 250 VA
X 16 fuse 1,0 A delayed
0 appr. 85 % appr. 0,93
-40 ... +60
C) H (180
IP 23 C
530 mm
230 mm
630 mm
49 kg
0
50 V DC
0 C
-20 ... +40 0 C
C) / B (130 fuse 6,3 A delayed
1~, 230 V / 250 VA fuse 1,0 A delayed
0 C) appr. 85 % appr. 0,93
-40 ... +60
-20 ... +40 0 C
H (180
IP 23 C
0
530 mm
230 mm
630 mm
56 kg
50 V DC
0 C
C) / B (130 fuse 6,3 A delayed
1~, 230 V / 250 VA fuse 1,0 A delayed
0 C)
© Kemppi oy Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 – 15
10. terms of guarantee
Kemppi Oy provides a guarantee for products manufactured and sold by them if defects in manufacture and materials occur. Guarantee repairs must be carried out only by an Authorised
Kemppi Service Agent. Packing, freight and insurance costs to be paid by orderer. The guarantee is effected on the date of purchase. Verbal promises which do not comply with the terms of guarantee are not binding on guarantor.
Limitations on guarantee
The following conditions are not covered under the terms of guarantee: defects due to natural wear and tear, non-compliance with operating and maintenance instructions, connection to incorrect or faulty supply voltage (including voltage surges outside equipment spec.), incorrect gas pressure, overloading, transport or storage damage, fire of damage due to natural causes i.e. lightning or flooding.
This guarantee does not cover direct or indirect travelling costs, daily allowances or accommodation.
Note: Under the terms of guarantee, welding torches and their consumables, feeder drive rolls and feeder guide tubes are not covered. Direct or indirect damage due to a defective product is not covered under the guarantee. The guarantee is void if changes are made to the product without approval of the manufacturer, or if repairs are carried out using non-approved spare parts.
The guarantee is also void if repairs are carried out by non-authorised agents.
Undertaking guarantee repairs
Guarantee defects must be informed to Kemppi or authorised Kemppi Service Agents within the guarantee period. Before any guarantee work is undertaken, the customer must provide proof of guarantee or proof of purchase, and serial number of the equipment in order to validate the guarantee.
The parts replaced under the terns of guarantee remain the property of Kemppi.
Following the guarantee repair, the guarantee of the machine or equipment, repaired or replaced, will be continued to the end of the original guarantee period.
16 – Kemppi pro evolution 300, 400, 500, 300 mvu, 400 mvu, 500 mvu / 0617 © Kemppi oy
KEMPPI OY
PL 13
FIN – 15801 LAHTI
FINLAND
Tel (03) 899 11
Telefax (03) 899 428 www.kemppi.com
KEMPPIKONEET OY
PL 13
FIN – 15801 LAHTI
FINLAND
Tel (03) 899 11
Telefax (03) 7348 398 e-mail: myynti.fi @kemppi.com
KEMPPI SVERIGE AB
Box 717
S – 194 27 UPPLANDS VÄSBY
SVERIGE
Tel (08) 590 783 00
Telefax (08) 590 823 94 e-mail: [email protected]
KEMPPI NORGE A/S
Postboks 2151, Postterminalen
N – 3103 TØNSBERG
NORGE
Tel 33 34 60 00
Telefax 33 34 60 10 e-mail: [email protected]
KEMPPI DANMARK A/S
Literbuen 11
DK – 2740 SKOVLUNDE
DANMARK
Tel 44 941 677
Telefax 44 941 536 e-mail:[email protected]
KEMPPI BENELUX B.V.
Postbus 5603
NL – 4801 EA BREDA
NEDERLAND
Tel +31 (0)76-5717750
Telefax +31 (0)76-5716345 e-mail: [email protected]
KEMPPI (UK) Ltd
Martti Kemppi Building
Fraser Road
Priory Business Park
BEDFORD, MK443WH
ENGLAND
Tel 0845 6444201
Fax 0845 6444202 e-mail: [email protected]
KEMPPI FRANCE S.A.
65 Avenue de la Couronne des Prés
78681 EPONE CEDEX
FRANCE
Tel (01) 30 90 04 40
Telefax (01) 30 90 04 45 e-mail: [email protected]
KEMPPI GmbH
Otto – Hahn – Straße 14
D – 35510 BUTZBACH
DEUTSCHLAND
Tel (06033) 88 020
Telefax (06033) 72 528 e-mail:[email protected]
KEMPPI SP. z o.o.
Ul. Piłsudskiego 2
05-091 ZA¸BKI
Poland
Tel +48 22 781 6162
Telefax +48 22 781 6505 e-mail: [email protected]
KEMPPI WELDING
MACHINES AUSTRALIA PTY LTD
P.O. Box 404 (2/58 Lancaster Street)
Ingleburn NSW 2565, Australia
Tel. +61-2-9605 9500
Telefax +61-2-9605 5999 e-mail: [email protected]
Ver. 9
www.kemppi.com
डाउनलोड
सार्वजनिक लिंक अपडेट किया गया
आपकी चैट का सार्वजनिक लिंक अपडेट कर दिया गया है. You may view and manage your chat links after registration here.
दस्तावेज़ सार्वजनिक लिंक
विज्ञापन
