Intel SERVER SYSTEM SR2500AL User's Guide
Annonce
Annonce
Intel
®
Server System SR2500AL
User’s Guide
A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/
Products
Intel Order Number D31969-004
Disclaimer
Information in this document is provided in connection with Intel® products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's
Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not designed, intended or authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of the Intel product could create a situation where personal injury or death may occur. Intel may make changes to specifications and product descriptions at any time, without notice.
Intel server boards contain a number of high-density VLSI and power delivery components that need adequate airflow for cooling. Intel's own chassis are designed and tested to meet the intended thermal requirements of these components when the fully integrated system is used together. It is the responsibility of the system integrator that chooses not to use Intel developed server building blocks to consult vendor datasheets and operating parameters to determine the amount of airflow required for their specific application and environmental conditions. Intel Corporation can not be held responsible if components fail or the server board does not operate correctly when used outside any of their published operating or non-operating limits.
Intel, Intel Pentium, and Intel Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2006-2007, Intel Corporation. All Rights Reserved ii Intel® Server System SR2500AL User’s Guide
Safety Information
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information on the
Intel
®
Deployment Assistant CD server/sb/cs-010770.htm
.
and/or at http://support.intel.com/support/motherboards/
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warnund Sicherheitshinweise in diesem Dokument, bevor
Sie eine der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu
Intel-Serverplatinen und Servergehäusen auf der Intel
®
Deployment Assistant CD unter http://support.intel.com/support/motherboards/server/sb/cs-010770.htm
.
oder
Consignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce document avant de suivre toute instruction. Consultez Intel Server Boards and Server
Chassis Safety Information sur le Intel
®
Deployment Assistant CD ou bien rendez-vous sur le site http://support.intel.com/support/motherboards/server/sb/cs-010770.htm
.
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety
Information en el Intel
®
Deployment Assistant CD motherboards/server/sb/cs-010770.htm
.
y/o en http://support.intel.com/support/
重要安全指导
在执行任何指令之前，请阅读本文档中的所有注意事项及安全声明。 和/或
http://support.intel.com/support/motherboards/server/sb/CS-010770.htm
上的 Intel
Server Boards and Server Chassis Safety Information（《Intel
服务器主板与服务器机箱安全信息》）。
iv Intel® Server System SR2500AL User’s Guide
Warnings
Heed safety instructions: Before working with your server product, whether you are using this guide or any other resource as a reference, pay close attention to the safety instructions. You must adhere to the assembly instructions in this guide to ensure and maintain compliance with existing product certifications and approvals. Use only the described, regulated components specified in this guide. Use of other products / components will void the UL listing and other regulatory approvals of the product and will most likely result in noncompliance with product regulations in the region(s) in which the product is sold.
System power on/off: The power button DOES NOT turn off the system AC power. To remove power from system, you must unplug the AC power cord from the wall outlet.
Make sure the AC power cord is unplugged before you open the chassis, add, or remove any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power, telephone, and communication cables. Turn off the server and disconnect the power cord, telecommunications systems, networks, and modems attached to the server before opening it. Otherwise, personal injury or equipment damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground any unpainted metal surface on your server when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a board from its protective wrapper or from the server, place the board component side up on a grounded, static free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that you can grip with your fingertips or with a pair of fine needle nosed pliers. If your jumpers do not have such a tab, take care when using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with the pliers, never the wide sides. Gripping the wide sides can damage the contacts inside the jumper, causing intermittent problems with the function controlled by that jumper. Take care to grip with, but not squeeze, the pliers or other tool you use to remove a jumper, or you may bend or break the pins on the board.
Intel® Server System SR2500AL User’s Guide v
vi Intel® Server System SR2500AL User’s Guide
Preface
About this Manual
Thank you for purchasing and using the Intel ®
Intel ® Server System SR2500ALBRP.
Server System SR2500ALLX and/or the
This manual is written for system technicians who are responsible for troubleshooting, upgrading, and repairing this server system. This document provides reference information, feature information, and step by step instructions on how to add and replace components on the server system. For the latest version of this manual, see http:// support.intel.com/support/motherboards/server/chassis/SR2500/ .
Manual Organization
Chapter 1 provides a list of reference resources. In this chapter you will find a list of technical documents that give additional details on the Intel
SR2500ALLX and/or the Intel they can be found.
®
®
Server System
Server System SR2500ALBRP, and the location where
Chapter 2 provides a brief overview of the server system. In this chapter, you will find a list of the server system features, illustrations of the product, and product diagrams to help you identify components and their locations.
Chapter 3 provides instructions on using the utilities that are shipped with the board or that may be required to update the system. This includes how to navigate through the
BIOS Setup screens, how to perform a BIOS update, and how to reset the password or
CMOS. Information about the specific BIOS settings and screens is available in the Intel
®
5000 Series Chipsets Server Board Family Datasheet.
®
5000 Series Chipsets Server Board Family Datasheet. See “Server System References” for a link to the Intel
Chapter 4 provides instructions on adding and replacing components. Use this chapter for step-by-step instructions and diagrams for installing or replacing components such as the fans, power supply, drives, and other components.
At the back of this manual, you will find technical specifications, regulatory information,
"getting help" information, and the warranty.
Product Contents
The Intel ® Server System SR2500ALLX and/or the Intel ® Server System SR2500ALBRP ships with the Intel ® Server Board S5000PAL. For further information, see the Intel
Server Board S5000PAL User’s Guide.
®
There are two versions of this server system: the Intel
SR2500ALLXR (SAS/SATA version) and the Intel
®
®
Server System SR2500ALLX/
Server System SR2500ALBRP/
SR2500ALBRPR (SATA only version). The contents of each server system are listed below.
Intel
®
Server System SR2500ALLX/SR2500ALLXR Contents
Your Intel ® items:
Server System SR2500ALLX/SR2500ALLXR ships with the following
• Intel ® Server Board S5000PAL, installed in the server system
• One 750 W power supply module, installed in the server system
• A box of hardware components, referred to below as the "hardware box"
• Low profile riser, installed in the server system
• Full height profile riser, installed in the server system
• Optical drive tray assembly, in hardware box
• Bridge board, installed in the server system
• Optical drive cable, installed in the server system
• Chassis intrusion switch, integrated into the server system riser
• Attention document, in the server system product box
• Quick Start User's Guide, in the server system product box
• One 32-6mm flat screw for installing the optical drive component, in the hardware box
• Rack handles, in the hardware box
• Peripheral bay filler panel, in the hardware box
• Standard control panel, installed in the server system
• Active SAS/SATA mid-plane, installed in the server system viii Intel® Server System SR2500AL User’s Guide
Intel
®
Server System SR2500ALBRP/SR2500ALBRPR
Contents
Your Intel ® items:
Server System SR2500ALBRP/SR2500ALBRPR ships with the following
• Intel ® Server Board S5000PAL, installed in the server system
• One 750 W power supply module, installed in the server system
• A box of hardware components, referred to below as the "hardware box"
• Low profile riser, installed in the server system
• Full height profile riser, installed in the server system
• Optical drive tray assembly, in the hardware box
• Bridge board, installed in the server system
• Optical drive cable, installed in the server system
• Chassis intrusion switch, integrated into the server system riser
• Attention document, in the server system product box
• Quick Start User's Guide, in the server system product box
• One 32-6mm flat screw for installing the optical drive component, in the hardware box
• Rack handles, in the hardware box
• Peripheral bay filler panel, in the hardware box
• Standard control panel, installed in the server system
• Passive mid-plane, installed in the server system
Intel® Server System SR2500AL User’s Guide ix
x Intel® Server System SR2500AL User’s Guide
Table of Contents
Safety Information ..................................................................................................... iii
Important Safety Instructions ................................................................................................ iii
Wichtige Sicherheitshinweise ............................................................................................... iii
Consignes de sécurité .......................................................................................................... iii
Instrucciones de seguridad importantes ............................................................................... iii
Preface ....................................................................................................................... vii
About this Manual ................................................................................................................ vii
Manual Organization ............................................................................................................ vii
Product Contents .................................................................................................................viii
Intel
®
Server System SR2500ALLX/SR2500ALLXR Contents ...................................viii
Intel
®
Server System SR2500ALBRP/SR2500ALBRPR Contents .............................. ix
Chapter 1: Server System References ..................................................................... 1
Chapter 2: Server System Features .......................................................................... 3
Chassis Component Identification ......................................................................................... 6
Internal Components ..................................................................................................... 6
Configuration Jumpers ........................................................................................................... 9
RAID Support ....................................................................................................................... 13
Standard Control Panel ............................................................................................... 18
Intel
®
Local Control Panel ........................................................................................... 19
Bezels .......................................................................................................................... 20
Peripheral Devices ............................................................................................................... 22
Hard Disk Drives .......................................................................................................... 22
Slimline Optical Drive Carrier ...................................................................................... 23
Advanced Management Options ......................................................................................... 23
Intel® Remote Management Module ........................................................................... 23
Rack-Mounted Systems ....................................................................................................... 23
Chapter 3: Hardware Installations and Upgrades ................................................. 25
Before You Begin ................................................................................................................. 25
Tools and Supplies Needed ........................................................................................ 25
System References ..................................................................................................... 25
Removing and Installing from a Rack .................................................................................. 25
Fixed Bracket Rack Mount Removal ........................................................................... 25
Fixed Bracket Rack Mount Installation ........................................................................ 26
Basic Rail Rack Mount Removal ................................................................................. 27
Basic Rail Rack Mount Installation .............................................................................. 27
Tool-less Rail Rack Mount Servicing ........................................................................... 28
Removing and Installing the Front Bezel ............................................................................. 28
Intel® Server System SR2500AL User’s Guide xi
xii
Removing the Front Bezel ........................................................................................... 29
Installing the Front Bezel ............................................................................................. 30
Removing and Installing the System Cover ........................................................................ 30
Removing the System Cover ...................................................................................... 30
Installing the Server System Cover ............................................................................. 31
Removing and Installing the Processor Air Duct ................................................................. 32
Removing the Processor Air Duct ............................................................................... 32
Installing the Processor Air Duct ................................................................................. 34
Installing and Removing Memory ........................................................................................ 35
Installing DIMMs .......................................................................................................... 35
Removing DIMMs ........................................................................................................ 37
Installing the Processor ............................................................................................... 37
Installing the Heat Sink(s) ........................................................................................... 39
Removing a Processor ................................................................................................ 40
Removing and Installing the Small Air Baffle ...................................................................... 40
Removing the Small Air Baffle .................................................................................... 41
Installing the Small Air Baffle ...................................................................................... 41
Removing and Installing the Large Air Baffle ...................................................................... 42
Removing the Large Air Baffle .................................................................................... 42
Installing the Large Air Baffle ...................................................................................... 43
Installing and Removing a Hot-swap Hard Drive ................................................................. 44
Installing a SAS or SATA Hot-swap Hard Disk Drive .................................................. 44
Removing a SAS or SATA Hot-swap Hard Disk Drive ................................................ 47
Installing or Removing a Slimline Optical Drive or Internal USB Floppy ............................. 47
Installing a Slimline Optical Drive or Internal USB Floppy .......................................... 48
Removing a Slimline Optical Drive or Internal USB Floppy ........................................ 49
Installing a Tape Drive ......................................................................................................... 51
Installing a Sixth Hard Drive ................................................................................................ 54
Filling Empty Server System Bays ...................................................................................... 57
Installing and Removing the PCI Riser Assembly ............................................................... 57
Removing the PCI Riser Assembly ............................................................................. 57
Installing the PCI Riser Assembly ............................................................................... 59
Replacing a PCI Riser Card ................................................................................................ 60
Removing a PCI Riser Card ........................................................................................ 60
Installing a PCI Riser Card .......................................................................................... 62
Installing and Removing a PCI Add-in Card ........................................................................ 63
Installing a PCI Add-in Card ........................................................................................ 63
Removing a PCI Add-in Card ...................................................................................... 64
Installing the I/O Expansion Module(s) ....................................................................... 66
Removing the I/O Expansion Module(s) ..................................................................... 67
Installing the Intel
®
RMM and Intel
®
RMM NIC ........................................................... 68
Removing the Intel
®
RMM and Intel
®
RMM NIC ......................................................... 70
Replacing the Mid-plane Board ........................................................................................... 71
Removing the Mid-plane Board ................................................................................... 71
Intel® Server System SR2500AL User’s Guide
Installing the Mid-plane Board ..................................................................................... 72
Replacing the Backplane ..................................................................................................... 74
Removing the Backplane ............................................................................................. 74
Installing the Backplane ............................................................................................... 76
Installing and Removing the RAID Activation Key and the RAID Mini DIMM ...................... 77
Installing the RAID Activation Key and the RAID Mini DIMM ...................................... 77
Removing the RAID Activation Key and the RAID Mini DIMM .................................... 78
Installing and Removing the RAID Battery Backup Unit (BBU) ........................................... 79
Installing the RAID Battery Backup Unit ...................................................................... 79
Removing the RAID Battery Backup Unit .................................................................... 80
Installing and Removing the Server Board .......................................................................... 81
Installing the Server Board .......................................................................................... 81
Removing the Server Board ........................................................................................ 82
Replacing the Backup Battery ............................................................................................. 84
Replacing the Power Supply ................................................................................................ 86
Replacing the Power Distribution Module ............................................................................ 88
Replacing the Control Panel ................................................................................................ 89
Replacing a Fan Module ...................................................................................................... 91
Replacing a Redundant Fan Module ........................................................................... 91
Replacing a Fixed Fan Module .................................................................................... 93
Replacing a Redundant System Fan ................................................................................... 95
Replacing a Fixed Fan ......................................................................................................... 97
Installing and Removing the Rack Handles ......................................................................... 98
Installing the Rack Handles ......................................................................................... 98
Removing the Rack Handles ....................................................................................... 99
Chapter 4: Server Utilities ...................................................................................... 101
Using the BIOS Setup Utility .............................................................................................. 101
Starting Setup ............................................................................................................ 101
If You Cannot Access Setup ...................................................................................... 101
Setup Menus ............................................................................................................. 101
Upgrading the BIOS ........................................................................................................... 103
Preparing for the Upgrade ......................................................................................... 103
Upgrading the BIOS .................................................................................................. 104
Clearing the Password ....................................................................................................... 104
Clearing the CMOS ............................................................................................................ 105
Appendix A: Technical Reference ........................................................................ 107
Cable Routing .................................................................................................................... 107
Fan Connections ................................................................................................................ 108
750W Single Power Supply Input Voltages ....................................................................... 109
750W Single Power Supply Output Voltages .................................................................... 109
System Environmental Specifications ................................................................................ 110
Appendix B: Troubleshooting ............................................................................... 111
Intel® Server System SR2500AL User’s Guide xiii
Resetting the System ........................................................................................................ 111
Problems following Initial System Installation .................................................................... 112
First Steps Checklist ................................................................................................. 112
Hardware Diagnostic Testing ............................................................................................ 112
Verifying Proper Operation of Key System Lights ..................................................... 113
Confirming Loading of the Operating System ........................................................... 113
Specific Problems and Corrective Actions ........................................................................ 113
Power Light Does Not Light ...................................................................................... 114
No Characters Appear on Screen ............................................................................. 114
Characters Are Distorted or Incorrect ....................................................................... 115
System Cooling Fans Do Not Rotate Properly .......................................................... 115
Drive Activity Light Does Not Light ............................................................................ 116
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light ............................ 116
Cannot Connect to a Server ...................................................................................... 116
Problems with Network ............................................................................................. 117
System Boots when Installing PCI Card ................................................................... 118
Problems with Newly Installed Application Software ................................................. 118
Problems with Application Software that Ran Correctly Earlier ................................ 118
Devices are not Recognized under Device Manager (Microsoft* Windows* Operating
System) ......................................................................................................... 119
Hard Drive(s) are not Recognized ............................................................................. 119
Bootable CD-ROM Disk Is Not Detected .................................................................. 119
LED Information ........................................................................................................ 120
BIOS POST Beep Codes .......................................................................................... 120
Appendix C: Intel
®
Server Issue Report Form .....................................................123
Appendix D: LED Decoder .....................................................................................127
Appendix E: Getting Help .......................................................................................133
World Wide Web ............................................................................................................... 133
Telephone ......................................................................................................................... 133
Appendix F: Regulatory and Compliance Information ........................................137
Product Regulatory Compliance ........................................................................................ 137
Product Safety Compliance ....................................................................................... 137
Product Regulatory Compliance References ............................................................ 138
Electromagnetic Compatibility Notices .............................................................................. 141
FCC Verification Statement (USA) ............................................................................ 141
Industry Canada (ICES-003) ..................................................................................... 142
Europe (CE Declaration of Conformity) ..................................................................... 142
VCCI (Japan) ............................................................................................................ 142
BSMI (Taiwan) .......................................................................................................... 142
Korean Compliance (RRL) ........................................................................................ 143
CNCA (CCC-China) .................................................................................................. 143
Product Ecology Compliance .................................................................................... 143 xiv Intel® Server System SR2500AL User’s Guide
Regulated Specified Components ............................................................................. 147
End-of-Life / Product Recycling ......................................................................................... 148
Appendix G: Warranty ............................................................................................ 149
Limited Warranty for Intel® Chassis Subassembly Products ............................................ 149
Appendix H: Installation/Assembly Safety Instructions ..................................... 153
English ............................................................................................................................... 153
Deutsch .............................................................................................................................. 155
Français ............................................................................................................................. 157
Español .............................................................................................................................. 159
Chinese .............................................................................................................................. 161
Italiano ............................................................................................................................... 162
Appendix I: Safety Information ............................................................................. 165
English ............................................................................................................................... 165
Server Safety Information .......................................................................................... 165
Safety Warnings and Cautions .................................................................................. 165
Intended Application Uses ......................................................................................... 166
Site Selection ............................................................................................................. 166
Equipment Handling Practices .................................................................................. 166
Power and Electrical Warnings .................................................................................. 167
System Access Warnings .......................................................................................... 168
Rack Mount Warnings ............................................................................................... 168
Electrostatic Discharge (ESD) ................................................................................... 169
Other Hazards ........................................................................................................... 169
Deutsch .............................................................................................................................. 170
Sicherheitshinweise für den Server ........................................................................... 170
Sicherheitshinweise und Vorsichtsmaßnahmen ........................................................ 170
Zielbenutzer der Anwendung ..................................................................................... 171
Standortauswahl ........................................................................................................ 171
Handhabung von Geräten ......................................................................................... 171
Warnungen zu Netzspannung und Elektrizität .......................................................... 172
Warnhinweise für den Systemzugang ....................................................................... 173
Warnhinweise für Racks ............................................................................................ 173
Elektrostatische Entladungen (ESD) ......................................................................... 174
Andere Gefahren ....................................................................................................... 174
Français ............................................................................................................................. 175
Consignes de securite sur le serveur ........................................................................ 175
Séurité: avertissements et mises en garde ............................................................... 175
Domaines d’utilisation prévus .................................................................................... 176
Sélection d’un emplacement ..................................................................................... 176
Pratiques de manipulation de l’équipement ............................................................... 177
Alimentation et avertissements en matiére d’électricité ............................................. 177
Avertissements sur le cordon d’alimentation ............................................................. 178
Intel® Server System SR2500AL User’s Guide xv
Avertissements sur l’accés au systéme .................................................................... 178
Avertissements sur le montage en rack .................................................................... 179
Décharges électrostatiques (ESD) ............................................................................ 180
Autres risques ........................................................................................................... 180
Périphériques laser ................................................................................................... 181
Español ............................................................................................................................. 181
Información de seguridad del servidor ...................................................................... 181
Advertencias y precauciones sobre seguridad ......................................................... 181
Aplicaciones y usos previstos ................................................................................... 182
Seleccién de la ubicación .......................................................................................... 182
Manipulacién del equipo ........................................................................................... 183
Advertencias de alimentacién y eléctricas ................................................................ 183
Advertencias sobre el cable de alimentación ............................................................ 183
Advertencias el acceso al sistema ............................................................................ 184
Advertencias sobre el montaje en bastidor ............................................................... 185
Descarga electrostática (ESD) .................................................................................. 185
Otros riesgos ............................................................................................................. 186 xvi Intel® Server System SR2500AL User’s Guide
List of Figures
Figure 1. Intel
®
Integrated Server System SR2500AL .............................................................. 3
Figure 2. ChassisComponents .................................................................................................. 6
Figure 3. Server Board Connector and Component Locations ................................................. 8
Figure 4. BIOS Select Jumper................................................................................................... 9
Figure 5. Recovery Jumpers ................................................................................................... 10
Figure 6. Light Guided Diagnostic LEDs ................................................................................. 11
Figure 7. Back Panel Connectors............................................................................................ 12
Figure 8. Passive Mid-Plane Components .............................................................................. 14
Figure 9. Active SAS/SATA Mid-Plane Components .............................................................. 15
Figure 10. Hot-Swap SAS/SATA Backplane Components (Front View) ................................. 16
Figure 11. Hot-Swap SAS/SATA Backplane Components (Rear View).................................. 17
Figure 12. Standard Control Panel.......................................................................................... 19
Figure 13. Intel
®
Local Control Panel...................................................................................... 20
Figure 14. Server System Back............................................................................................... 21
Figure 15. Optional Peripherals............................................................................................... 22
Figure 16. Front Bezel Supporting the Standard Control Panel .............................................. 28
Figure 17. Front Bezel Supporting the Intel
®
Local Control Panel .......................................... 28
Figure 18. Removing the Front Bezel...................................................................................... 29
Figure 19. Installing the Front Bezel........................................................................................ 30
Figure 20. Removing the Server System Cover...................................................................... 31
Figure 21. Installing the Server System Cover........................................................................ 32
Figure 22. Removing the Processor Air Duct .......................................................................... 33
Figure 23. Removing the Processor 2 Air Dam (Optional - only if two processors are installed).
34
Figure 24. Installing the Processor Air Duct ............................................................................ 35
Figure 25. Installing the Memory ............................................................................................. 36
Figure 26. Lifting the Processor Socket Handle ...................................................................... 38
Figure 27. Installing the Processor.......................................................................................... 38
Figure 28. Removing the Socket Cover .................................................................................. 39
Figure 29. Installing the Heat Sink (2U Passive Heat Sink Shown) ........................................ 39
Figure 30. Removing the Small Air Baffle ............................................................................... 41
Figure 31. Installing the Small Air Baffle ................................................................................. 42
Figure 32. Removing the Large Air Baffle ............................................................................... 43
Figure 33. Installing the Large Air Baffle ................................................................................. 44
Figure 34. Removing Hot-swap Disk Carrier from the Server System .................................... 45
Figure 35. Removing Retention Device from Drive Carrier ..................................................... 45
Figure 36. Installing Hard Drive into Carrier ............................................................................ 46
Figure 37. Install Drive Assembly into the Server System ...................................................... 46
Figure 38. Installing an Optical Drive into the Drive Tray ........................................................ 48
Figure 39. Installing an Optical Drive Assembly into the Server System ................................ 49
Figure 40. Removing the Slimline Optical Drive Assembly from the Server System .............. 50
Figure 41. Removing the Slimline Optical Drive from the Tray ............................................... 50
Intel® Server System SR2500AL User’s Guide xvii
Figure 42. Installing Filler Blank into the Server System ........................................................ 51
Figure 43. Removing Tape Drive Filler Panel from the Server System .................................. 52
Figure 44. Removing Sixth Drive Filler Panel from the Server System .................................. 52
Figure 45. Inserting a Tape Drive into the Carrier................................................................... 53
Figure 46. Installing Tape Drive Assembly into the Server System ........................................ 53
Figure 47. Installing Sixth HDD Bracket.................................................................................. 54
Figure 48. Installing Power and SATA Cables (Active Mid-Plane Installed) ........................... 55
Figure 49. Installing Power and SATA Cables (Passive Mid-Plane Installed) ........................ 56
Figure 50. Installing the Filler Panels...................................................................................... 57
Figure 51. Removing PCI Riser Assembly from the Server System....................................... 58
Figure 52. Installing PCI Riser Assembly into the Server System .......................................... 59
Figure 53. Removing the PCI Riser Card from the Server System (Full Height Side)............ 61
Figure 54. Installing PCI Riser Card into the Server System .................................................. 62
Figure 55. Installing a Full Height Add-In Card ....................................................................... 64
Figure 56. Removing a Full Height Add-In Card ..................................................................... 65
Figure 57. Installing the I/O Expansion Module to the Server Board ...................................... 66
Figure 58. Removing the I/O Expansion Module(s) from the Server Board............................ 67
Figure 59. Installing the Intel
®
RMM and the Intel
®
Figure 60. Removing the Intel
®
RMM and the Intel
RMM NIC Module to the Server System 69
®
RMM NIC Module from the Server System
70
Figure 61. Removing the Bridge Board from the Server System............................................ 71
Figure 62. Removing the Mid-plane from the Server System ................................................. 72
Figure 63. Installing the Mid-plane into the Server System .................................................... 73
Figure 64. Installing the Bridge Board into the Server System ............................................... 73
Figure 65. Removing the Backplane from the Server System ................................................ 75
Figure 66. Installing the Backplane into the Server System ................................................... 76
Figure 67. Installing the RAID Activation Key and the RAID Mini DIMM ................................ 77
Figure 68. Removing the RAID Activation Key and the RAID Mini DIMM .............................. 78
Figure 69. Installing the RAID Battery Backup Unit ................................................................ 79
Figure 70. Removing the RAID Battery Backup Unit .............................................................. 80
Figure 71. Installing the Server Board .................................................................................... 81
Figure 72. Removing the Server Board .................................................................................. 83
Figure 73. Replacing the Backup Battery ............................................................................... 85
Figure 74. Removing Power Supply Filler Panel from the Server System.............................. 86
Figure 75. Removing Power Supply Module from the Server System.................................... 87
Figure 76. Installing Power Supply Module into the Server System ....................................... 87
Figure 77. Installing Power Supply Filler Panel into the Server System ................................. 87
Figure 78. Removing the Power Distribution Module.............................................................. 88
Figure 79. Removing Standard Control Panel Module from the Server System..................... 90
Figure 80. Installing Control Panel Module into the Server System........................................ 90
Figure 81. Removing the Redundant Fan Module .................................................................. 92
Figure 82. Installing the Redundant Fan Module .................................................................... 92
Figure 83. Removing the Fixed Fan Module........................................................................... 94
Figure 84. Installing the Fixed Fan Module............................................................................. 94
Figure 85. Removing a Fan from the Redundant Fan Module................................................ 96
Figure 86. Installing a Fan into the Redundant Fan Module ................................................... 96
Figure 87. Removing a Fan from the Fixed Fan Module ........................................................ 97 xviii Intel® Server System SR2500AL User’s Guide
Figure 88. Installing a Fan into the Fixed Fan Module ............................................................ 98
Figure 89. Installing the Rack Handle ..................................................................................... 99
Figure 90. Removing the Rack Handle ................................................................................. 100
Figure 91. Clear Password Jumper....................................................................................... 105
Figure 92. Clear CMOS Jumper............................................................................................ 106
Figure 93. Cable Routing ...................................................................................................... 107
Figure 94. Connecting the Non-redundant Fan Power Cables to the Passive Mid-plane Board .
108
Figure 95. Connecting the Redundant Fan Power Cables to the Active Mid-plane Board.... 108
Figure 96. Diagnostic LED Placement Diagram.................................................................... 128
Intel® Server System SR2500AL User’s Guide xix
xx Intel® Server System SR2500AL User’s Guide
List of Tables
Table 1. Server System References ......................................................................................... 1
Table 2. Intel
®
Server System SR2500ALLX and/or the Intel
®
Server System SR2500ALBRP
Feature Summary ...................................................................................................................... 4
Table 3. NIC LED Descriptions ............................................................................................... 13
Table 4. Setup Menu Key Use .............................................................................................. 102
Table 5. Power Supply Output Capability .............................................................................. 109
Table 6. System Environmental Specifications ..................................................................... 110
Table 7. Resetting the System .............................................................................................. 111
Table 8. LED Information ......................................................................................................120
Table 9. POST Error Beep Codes ......................................................................................... 120
Table 10. Error Beep Codes Generated by Intel
®
Remote Management Module ................ 121
Table 11. POST Progress Code LED Example ..................................................................... 127
Table 12. Diagnostic LED POST Code Decoder ................................................................... 128
Table 13. Product Regulatory Compliance Markings ............................................................ 138
Table 14. Product Ecology Compliance Markings ................................................................. 144
Table 15. Other Markings ...................................................................................................... 146
Intel® Server System SR2500AL User’s Guide xxi
xxii Intel® Server System SR2500AL User’s Guide
1
Server System References
Four product codes are associated with the Intel® Server System SR2500AL:
• SR2500ALLX
• SR2500ALBRP
• SR2500ALLXR
• SR2500ALBRPR
Unless noted otherwise, all references to the Intel® Server System SR2500AL refer to all four product codes.
If you need more information about this product or information about the accessories that can be used with this server chassis, use the following resources.
Table 1. Server System References
For this information or software
Use this Document or Software
For in-depth technical information about the server system, including sub-system overviews and mechanical drawings
For basic BIOS settings and chipset information
For in-depth BIOS information
For in-depth firmware information on the
Baseboard Management
Controller (BMC)
For in-depth information on Intel
®
I/O Acceleration
Technology
Intel
®
Server Chassis SR2500 Technical Product Specification
Found at: http://support.intel.com/support/motherboards/server/chassis/
SR2500/
Intel
®
Server Board S5000PAL Technical Product Specification
Found at: http://support.intel.com/support/motherboards/server/S5000PAL/
Intel
®
5000 Series Chipsets Server Board Family Datasheet
Found at: http://support.intel.com/support/motherboards/server/S5000PAL/
Intel
®
S5000 Server Board Family Server BIOS External Product
Specification
Found: available to order by contacting your Intel field representative; Intel reference number 19953
ESB2 Baseboard Management Controller Core External Product
Specification for the Intel
®
S5000 Server Board Family
Found: available to order by contacting your Intel field representative; Intel reference number 19692.
Intel
®
I/O Acceleration Technology Improves Intel Server Platform
Network Performance, Reliability, and Efficiency whitepaper
Found: available from your Intel field representative
2
Table 1. Server System References
For this information or software
Use this Document or Software
If you just received this product and need to install it
For virtual system tours and interactive repair information
Accessories or other Intel server products
Intel
®
Integrated Server System SR2500AL Quick Start User's
Guide
Found: in the product box
A link to the SMaRT Tool is available under "Other Resources" at the right side of the screen at http://support.intel.com/support/motherboards/server/chassis/
SR2500
Spares and Configuration Guide
Found: available from your Intel field representative or on the
Server Configurator Tool at http://indigo.intel.com/ serverconfiguratortool/default.aspx
Tested HardwareOperating Systems List
Found at: http://support.intel.com/support/motherboards/server/S5000PAL/
Hardware (peripheral boards, adapter cards) and operating systems that have been tested with this product
To make sure your system falls within the allowed power budget
For software to manage your Intel
For diagnostics test software
®
server
Power Budget Tool
Found at: http://support.intel.com/support/motherboards/server/S5000PAL/
Intel
®
System Management Software
Found at: http://support.intel.com/support/motherboards/server/sysmgmt/ index.htm
Diagnostics
Found at: http://support.intel.com/support/motherboards/server/S5000PAL/
Intel® Server System SR2500AL User’s Guide
2
Server System Features
This chapter briefly describes the main features of the server system. This chapter provides illustrations of the product, a list of the server system features, and diagrams showing the location of important components and connections on the server system.
AF000027
Figure 1. Intel
®
Integrated Server System SR2500AL
4
Table 2 summarizes the features of the server system.
Table 2. Intel
®
Server System SR2500ALLX and/or the Intel
®
Server System
SR2500ALBRP Feature Summary
Feature
Dimensions
Server Board
Description
•
3.44 inches (87.30 mm) high
•
16.93 inches (430 mm) wide
•
27.75 inches (704.8 mm) deep
•
65 pounds (29.5 kg) - max chassis weight
Intel
®
Server Board S5000PAL
Memory
Chipset
Peripheral Interfaces
I/O Controll
Video
LAN
Expansion Capabilities
Product Specification for information on processor support.
•
Eight DIMM slots supporting stacked DDR2 533/667 MHz
FBDIMM memory
•
Support for up to 32 GB DDR2 533/667 MHz FBDIMM memory
Intel
®
5000P chipset, consisting of:
•
Intel
®
5000P Memory Controller Hub (MCH)
•
Intel
®
6321ESB I/O Controller Hub
External connections:
•
Stacked PS/2* ports for keyboard and mouse
•
RJ45 Serial B port
•
Two RJ45 NIC connectors for 10/100/1000 Mb connections
•
Two USB 2.0 ports
Internal connections:
•
One USB port header, which supports two USB 2.0 ports
•
One DH10 Serial A header
•
Six Serial ATA 150 connectors with integrated RAID 0/1 support
•
One ATA-100 44-pin connector for optical drive support
•
SSI-compliant 24-pin control panel header
•
SSI-compliant 24-pin main power connector, supporting the
ATX-12V standard on the first 20 pins
National Semiconductor* PC87427 controller
On-board ATI* ES1000 video controller with 16 MB DDR SDRAM
Intel
®
82563EB dual port controller for 10/100/1000 Mbit/sec
Ethernet LAN connectivity
•
One low profile riser slot supporting 1U or 2U PCI Express* riser cards
•
One full height riser slot supporting 1U or 2U PCI-X* and PCI
Express* riser cards
Intel® Server System SR2500AL User’s Guide
Table 2. Intel
®
Server System SR2500ALLX and/or the Intel
®
Server System
SR2500ALBRP Feature Summary
Feature
Hard Drives
Peripherals
Control Panel (dependent on option selected)
LEDs and displays
(dependent on option selected)
Description
•
Five hot-swap SATA / SAS drives
•
Drive bay for sixth hot-swap SATA / SAS drive or a 3.5 inch tape drive
•
Slimline bay for IDE optical drive
•
PCI riser card bracket
•
Standard control panel
•
Intel
®
Local Control Panel
With standard control panel:
•
NIC1 Activity
•
NIC2 Activity
•
Power / Sleep
•
System Status
•
System Identification
•
Hard Drive Activity
Power Supply
Fans
USB
System Management
With Intel
®
Local Control Panel:
•
NIC1 Activity
•
NIC2 Activity
•
Power / Sleep
•
System Status
•
System Identification
•
Hard Drive Activity
•
LCD Display
Up to two 750W power supply modules
•
Non-redundant three fan option (BRP)
•
Redundant fan module option containing six system fans (LX)
•
Two non-redundant fans in power supply
•
Two front panel USB ports
•
One internal USB header providing two USB ports
Intel
®
System Management Software
Intel® Server System SR2500AL User’s Guide 5
6
Chassis Component Identification
This section helps you identify the components of your server system. If you are near the system, you can also use the Quick Reference Label provided on the inside of the chassis cover to assist in identifying components.
Internal Components
E
F
G
B
C
D
A
H
I
O
J
N
K
M
L
A
AF000028
A.
B.
C.
D.
Rack Handles
SAS/SATA Backplane
Air Baffles
Power Distribution Module
I.
Processor Air Duct
J.
System Fan Assembly (redundant option shown)
K.
Bridge Board
L.
Control Panel (standard control panel shown)
M.
Flex Bay - 6th HDD or Tape Drive (optional) E.
Power Supply Module Housing (supports up to two power supply modules)
F.
Riser Card Assembly
G.
Integrated Chassis Intrusion Switch
H.
System Memory (below duct in illustration)
N.
Hard Drive Bays
O.
Slimline Optical Drive Bay
Figure 2. ChassisComponents
Intel® Server System SR2500AL User’s Guide
Server Board Connector and Component
Locations
A B C D E F G H I
PP
FF
EE
DD
CC
BB
AA
OO
NN
LL
MM
KK
JJ
II
HH
GG
Z
O
P
Q
M
N
J
K
L
Y X W V U T S R
TP02071
Intel® Server System SR2500AL User’s Guide 7
8
A.
D.
G.
System Identification LED -
Blue
J.
Serial B Configuration Jumper
M.
DIMM Sockets
P.
S.
BIOS Bank Select Jumper
POST Code Diagnostic LEDs
Processor 2 Socket
Processor Fan 2 Header
B.
Intel
®
6321ESB IO Controller
Hub
E.
Intel
®
Adaptive Slot - Full
Height
H.
Back Panel I/O Ports
K.
System Fan 4 Header
N.
Intel
®
5000P MCH or Intel
®
5000X MCH
Q.
Processor Fan 1 Header
T.
Bridge Board Connector
C.
I/O Expansion Module
Connector
F.
PCI Express* Riser Slot - Low
Profile
I.
Status LED - Green/Amber
L.
System Fan 3Header
O.
Processor 1 Socket
V.
System Fan 2 Header
Y.
Battery
BB. System Fan 1 Header
W.
CPU Power Connector
Z.
Power Supply Management
Connector
CC. 24-pin SSI Control Panel
Connector
FF. SATA Port 2
II.
SATA Port 5
R.
Voltage Regulator Heat Sink
U.
ATA-100 Optical Drive
Connector (Power + IO)
X.
Main Power Connector
AA. Dual Port USB 2.0 Header
DD. SATA Port 0
EE. SATA Port 1
HH. SATA Port 4
KK. Intel
®
Remote Management
Module (RMM) Connector
NN. 3-pin IPMB Header
LL. System Recovery Jumpers
GG. SATA Port 3
JJ. SATA SW RAID 5 Activation
Key Connector
MM. Chassis Intrusion Switch
Header
PP. Serial A Header OO. Intel
®
Local Control Panel
Header
QQ. Intel
®
RMM NIC Connector
Figure 3. Server Board Connector and Component Locations
Intel® Server System SR2500AL User’s Guide
Configuration Jumpers
3
BIOS Select
J3H1
1-2: Force
Lower Bank
2-3: Normal
Operation (Default)
3
Jumper Name
BIOS Select
TP02087
Jumper Purpose
If pins 1-2 are jumpered, the BIOS in the lower bank will be selected on the next reset. These pins should be jumpered on 2-3 for normal operation.
Figure 4. BIOS Select Jumper
Intel® Server System SR2500AL User’s Guide 9
10
BMC Force
Update Mode
2
3
J1D2
Password
Reset
Disable
2
3
J1D1
Enable
2
3
J1D3
Clear
CMOS
TP02080
Jumper Name Jumper Purpose
CMOS Clear
Password Clear
If pins 2-3 are jumpered, the CMOS settings will be cleared on the next reset. These pins should be jumpered on 1-2 for normal operation.
If pins 2-3 are jumpered, administrator and user passwords will be cleared on the next reset. These pins should be jumpered on 1-2 for normal operation.
BMC Force Update Mode If pins 2-3 are jumpered, BMC Force Update Mode is enabled. These pins should be jumpered on 1-2 for normal operation.
Figure 5. Recovery Jumpers
Intel® Server System SR2500AL User’s Guide
Intel
®
Light Guided Diagnostics
The server board contains diagnostic LEDs to help you identify failed and failing components, and to help you identify the server from among several servers. Except for the ID LED, the status LED, and the 5V standby LED, the LEDs turn on (amber) only if a failure occurs.
N
A
POST
Code LEDs
B
C
D E F G H I J K
L
M
Light Guided
Diagnostics
Legend
A through N
A. POST Code LEDs
B. ID LED
C. Status LED
D. DIMM A1 Fault
E. DIMM A2 Fault
F. DIMM B1 Fault
G. DIMM B2 Fault
H. DIMM C1 Fault
I. DIMM C2 Fault
J. DIMM D1 Fault
K. DIMM D2 Fault
L. CPU 1 Fault
M. CPU 2 Fault
N. 5V Standby
CPU 2
Socket
CPU 1
Socket
Figure 6. Light Guided Diagnostic LEDs
AF000644
Intel® Server System SR2500AL User’s Guide 11
Back Panel Connectors
12
A
B C D E F G H
TP02081
A.
Mouse
C.
Serial Port B (RJ45)
E.
NIC 2 (10/100/1000 Mb)
G.
USB Port 6
B.
Keyboard
D.
NIC 1 (10/100/1000 Mb)
F.
Video
H.
USB Port 5
Figure 7. Back Panel Connectors
Intel® Server System SR2500AL User’s Guide
The NIC LEDs at the right and left of each NIC provide the following information.
Table 3. NIC LED Descriptions
Left
LED
Right
LED State
Off
Solid Amber
Blinking Amber
Off
Solid Amber
Solid Green
Description
No network connection
Network connection in place
Transmit/receive activity
10 Mbps connection (if left LED is on or blinking)
100 Mbps connection
1000 Mbps connection
RAID Support
The server system provides an embedded SATA controller that supports both 1.5 and 3.0
Gbps data transfer rates.
The BIOS Setup utility provides multiple drive configuration options on the Advanced |
ATA Controller setup page, some of which affect the ability to configure RAID. The
“Onboard SATA Controller” option is enabled by default. When this option is enabled, the
“SATA Mode” option can be set to either Legacy or Enhanced. The Legacy and Enhanced modes affect the RAID configuration as follows:
• Legacy supports four disk drives and does not provide RAID support.
• Enhanced supports six disk drives and is required for RAID configurations.
When the enhanced mode is selected, you can choose to enable or disable “AHCI Mode” or “Configure SATA as RAID”. Intel ® Embedded Server RAID Technology II is enabled by the option, “Configure SATA as RAID.” The Intel ® Embedded Server RAID
Technology II feature provides RAID modes 0, 1, and 10.
For RAID 0, 1, and 10, enclosure management is provided through the SATA_SGPIO connector on the server board when a cable is attached between this connector on the server board and to the backplane or I
2
C interface.
If RAID 5 is desired, the optional Intel ® RAID Activation Key AXXRAKSW5 can be installed. To enable RAID 5, this activation key is placed on the SATA Key connector that is located at the left side of the server board. For information on how to install the Intel ®
RAID Activation Key AXXRAKSW5 accessory to enable RAID 5, see the documentation that is included with the accessory kit.
For information on configuring RAID, see the RAID software user’s guide that is included on the Intel
®
Server Deployment Toolkit 2.0 CD .
Intel® Server System SR2500AL User’s Guide 13
SAS/SATA Mid-Planes
The mid-plane serves as the primary interface between the server board, hot-swap backplane, and control panel. Two midplanes are offered for this system: a passive SATA
(data cables required), and an active SAS/SATA RAID (no data cables required). The following diagrams show the location for each connector found on the mid-planes.
A
B
C
D
E
F
G
H
I
J
AF000047
A.
Mid-plane Power
B.
Fan 6 Power
C.
Fan 5 Power
D.
SATA 0-7 Connectors
E.
Bridge Board Connector
F.
Fan 4 Power
G.
Fan 3 Power
H.
Fan 1 Power
I.
Fan 2 Power
J.
Backplane Connectors
Figure 8. Passive Mid-Plane Components
Note: SATA connectors 6 and 7 are not used in the Intel the Intel
®
Server System SR2500ALBRP.
®
Server System SR2500ALLX and/or
14 Intel® Server System SR2500AL User’s Guide
A
B C
D
E
F
G
H
I
K
J
AF000046
A.
RAID Battery Connector
B.
Mid-plane Power Connector
C.
Fan 6 Power
D.
Fan 5 Power
E.
Bridge Board Connector
F.
Fan 4 Power
G.
Fan 3 Power
H.
Fan 2 Power
I.
Fan 1 Power
J.
Backplane Connectors
Figure 9. Active SAS/SATA Mid-Plane Components
Intel® Server System SR2500AL User’s Guide 15
Hot-Swap SAS/SATA Backplane
The backplane serves as an interface between the mid-plane board and the system drives.
The following diagrams show the location for each connector found on the backplane.
A
B
C
D
AF000045
.
A.
Optical Drive Connector
B.
USB Floppy Connector
C.
Control Panel Connector
D.
SAS/SATA Connectors
Figure 10. Hot-Swap SAS/SATA Backplane Components (Front View)
16 Intel® Server System SR2500AL User’s Guide
A
B C
D
E
AF000044
A.
Flex Bay Power
B.
Flex Bay Data
D.
Backplane Power
E.
Data Connectors (one for the flex bay and one for the mid-plane)
C.
IDE Connector
Figure 11. Hot-Swap SAS/SATA Backplane Components (Rear View)
Intel® Server System SR2500AL User’s Guide 17
Front of Server System
Standard Control Panel
The diagram below shows the features available on the standard control panel. Another option is the Intel ® Local Control Panel, which is discussed next.
A B C D E F G
H
18
I
A.
B.
Callout
C.
D.
E.
F.
G.
H.
L K J
AF000030
Feature
NIC 2 Activity LED
NIC 1 Activity LED
Power/Sleep Button
Power/Sleep LED
Hard Disk Drive
Activity LED
System Status LED
System Identification
LED
System Identification
Button
Function
Continuous green light indicates a link between the system and the network to which it is connected.
Blinking green light indicates network activity.
Continuous green light indicates a link between the system and the network to which it is connected.
Blinking green light indicates network activity.
Continuous green light indicates the system has power applied to it.
Blinking green indicates the system is in S1 sleep state.
No light indicates the power is off / is in ACPI S4 or S5 state.
Random blinking green light indicates hard disk drive activity (SAS or SATA).
No light indicates no hard disk drive activity.
Solid green indicates normal operation.
Blinking green indicates degraded performance.
Solid amber indicates a critical or non-recoverable condition.
Blinking amber indicates a non-critical condition.
No light indicates POST is running or the system is off.
Solid blue indicates system identification is active.
No light indicates system identification is not activated.
Solid blue indicates system identification is active.
No light indicates system identification is not activated.
Intel® Server System SR2500AL User’s Guide
I.
J.
K.
L.
Callout Feature
Reset Button
USB 2.0 Port
NMI Button
Video Port
Function
Reboots and initializes the system.
Allows you to attach a USB component to the front of the chassis.
Puts the server in a halt-state for diagnostic purposes.
Allows you to attach a video monitor to the front of the chassis.
The front and rear video ports cannot be used at the same time.
Figure 12. Standard Control Panel
Intel
®
Local Control Panel
The diagram below shows the features available on the Intel
®
Local Control Panel.
A B
O N M L K J I H G
AF000031
C
D
E
F
F.
G.
D.
E.
A.
B.
C.
Callout
H.
Feature
USB 2.0 Port
LCD Display
Menu Control Button,
Scroll Up
Menu Control Button,
Scroll Down
Menu Control Button,
Scroll Left
Menu Control Button,
Enter
System Identification
LED
Power/Sleep LED
Function
Allows you to attach a USB component to the front of the chassis.
Screen on which system information is displayed.
Scroll up one option at a time.
Scroll down one option at a time.
Move to the previous option.
Select option.
Solid blue indicates system identification is active.
No light indicates system identification is not activated.
Continuous green light indicates the system has power applied to it.
Blinking green indicates the system is in S1 sleep state.
No light indicates the power is off / is in ACPI S4 or S5 state.
Intel® Server System SR2500AL User’s Guide 19
I.
Callout
J.
K.
L.
M.
N.
O.
Feature
Power/Sleep Button
System Status LED
NIC 2 Activity LED
NIC 1 Activity LED
Hard Disk Activity
LED
Reset Button
USB 2.0 Port
Function
Continuous green light indicates a link between the system and the network to which it is connected.
Blinking green light indicates network activity.
Solid green indicates normal operation.
Blinking green indicates degraded performance.
Solid amber indicates a critical or non-recoverable condition.
Blinking amber indicates a non-critical condition.
No light indicates POST is running or the system is off.
Continuous green light indicates a link between the system and the network to which it is connected.
Blinking green light indicates network activity.
Random blinking green light indicates hard disk drive activity
(SAS or SATA).
No light indicates no hard disk drive activity.
Reboots and initializes the system.
Allows you to attach a USB component to the front of the system.
Figure 13. Intel
®
Local Control Panel
Bezels
The optional front bezels provide a snap-on design that allows for maximum airflow through the server chassis. Two bezels are available. One fits a system that has the standard control panel installed. The other is used for a chassis with the other Intel
®
Local
Control Panel. Each bezel provides a lock to secure the hard drive and optical drive area.
For instructions on installing either of the front bezels, see “Installing the Front Bezel” .
The order numbers for the bezels are:
• ADWBEZBLACK: Black bezel for use with the standard control panel.
• ADWLCDBEZEL: Black bezel for use with the Intel ® Local Control Panel.
20 Intel® Server System SR2500AL User’s Guide
Rear of Server System
A B C D
P
O
N
M
L K
J
I H G F E
TP02125
A.
Low Profile Add-in Card Slots
B.
Full Height PCI Add-in Card Slots
C.
Upper Power Supply Module
D.
Upper Power Receptacle
E.
Lower Power Receptacle
F.
Lower Power Supply Module
G.
Server Management NIC (Optional)
H.
I/O Module (Optional)
I.
USB 6
J.
USB 5
K.
Video
L.
DB-9 Serial A Connector Knockout
M.
NIC 2
N.
NIC 1
O.
RJ45 Serial B Connector
P.
PS2* Keyboard and Mouse Connectors
Figure 14. Server System Back
Intel® Server System SR2500AL User’s Guide 21
Peripheral Devices
The server system provides locations and hardware for installing hard drives, a USB floppy drive, CD-ROM drive, or DVD-ROM drive. The drives must be purchased separately. The following figure shows the available options.
A B
E D C
TP02126
.
A.
Slimline Optical Drive Bay
B.
Tape Drive Filler Panel
C.
6th HDD or Tape Drive Bay (Optional)
D.
Hard Disk Drive Bays
E.
HDD to Floppy Drive Conversion (Optional)
Figure 15. Optional Peripherals
Hard Disk Drives
The server system ships with five drive carriers for installing five SAS or Serial ATA
(SATA) hot-swap drives.
Note: SAS drives are supported on the Intel
®
Server System SR2500ALLX/SR2500ALLXR only.
One left drive bay can be converted to be used as a floppy bay. To use the bay for a floppy drive, the AXXFLOPHDDTRAY accessory kit must be used.
For instructions on installing hard drives, see “Installing and Removing a Hot-swap Hard
Drive” .
Note: Drives can consume up to 17 watts of power each. Drives must be specified to run at a maximum ambient temperature of 45C.
Note: The Intel
®
Server System SR2500ALLX and/or the Intel
®
Server System SR2500ALBRP does not support all SAS or Serial ATA (SATA) hard drives. See “Server System
References” for an Internet link to a list of supported hardware.
22 Intel® Server System SR2500AL User’s Guide
Slimline Optical Drive Carrier
The slimline optical drive carrier can be used with an optional optical drive. One slimline carrier is included with your server system; the optical drive must be purchased separately.
You cannot install both an optical drive and a USB floppy drive.
The slimline optical drive carrier can be inserted or removed only when system power is turned off. Drives in the optical drive carrier are NOT hot swappable. For installation instructions on installing an optical drive, see “Installing or Removing a Slimline Optical
Drive or Internal USB Floppy” .
To use one of the drives provided by Intel, use the following order codes:
• Slimline CD-ROM Drive: AXXSCD
• Slimline DVD/CDR Drive: AXXDVDCDR
Note: The Intel
®
Server System SR2500ALLX and/or the Intel
®
Server System SR2500ALBRP does not support all slimline optical drives. See “Server System References” for an
Internet link to a list of supported hardware. Intel provides accessory kits for these drives.
Advanced Management Options
Intel® Remote Management Module
The Intel
®
Remote Management Module is available to provide advanced server management features.
For installation instructions on installing the Intel ® Remote Management Module, see the instructions provided with the management module.
Rack-Mounted Systems
Your Intel ® Server System SR2500ALLX and/or the Intel ® Server System
SR2500ALBRP can be mounted into a rack. Intel provides three options to mount this server into a rack. When installing the chassis into a rack, Intel recommends you install systems from the bottom of the rack to the top. In other words, install the first system in the rack into the bottom position of the rack, the second system in the second position from the bottom, and so on. Instructions for installing your chassis into a rack are included in the rail kit.
Intel® Server System SR2500AL User’s Guide 23
24 Intel® Server System SR2500AL User’s Guide
3
Hardware Installations and
Upgrades
Before You Begin
Before working with your server product, pay close attention to the “Safety Information” at the beginning of this manual.
Tools and Supplies Needed
• Phillips* (cross head) screwdrivers (#1 bit and #2 bit)
• Needle nosed pliers
• Antistatic wrist strap and conductive foam pad (recommended)
System References
All references to left, right, front, top, and bottom assume the reader is facing the front of the server system as it would be positioned for normal operation.
Removing and Installing from a Rack
Three Intel
®
rack options are available to install the Intel and/or the Intel
®
®
Server System SR2500ALLX
Server System SR2500ALBRP in a rack. The options are the fixed bracket kit, the basic rail kit, and the tool-less rail kit. Only the tool-less rail kit allows you to service the server system while installed in a rack. The other rack options require the system to be removed from the rack before servicing.
Note: Follow all safety guidelines while removing a system from a rack to avoid injury.
Fixed Bracket Rack Mount Removal
1. Disconnect all cables from the back of the system.
Note: Remember to use the system LED to properly identify the system you are servicing.
2. Remove screws from the brackets and remove the system from the rack.
Fixed Bracket Rack Mount Installation
1. Fully extend a rail assembly; the finger tab for the extension lock is revealed.
2. Press the finger tab and slide the inside rail from the middle rail until it completely separates.
Note: The middle rail and outer rail cannot be separated.
3. Position an inside rail along one side of the chassis with the finger tab facing outward and located closer to the rear of the chassis.
4. Align the holes in the rail with the tabs on the chassis and place the rail against the chassis.
5. Slide the rail as far as it will go toward the front of the chassis to engage the tabs.
6. Fasten the rail to the chassis using one screw at the front of the chassis.
7. In the same manner, attach the other inside rail to the other side of the chassis
8. Using two screws, attach one nut bar to the inside of the rack post. Do not completely tighten the screws; leave them loose enough to allow insertion of the brackets in the next step.
9. Insert the slotted foot of a rail bracket between each nut bar and post.
10. Align the face of the bracket foot with the inside edge of the rack post and firmly tighten the screws.
11. Repeat steps 8 to 10 above to install the other 3 brackets (2 front & 2 back). Ensure all brackets are at the same height on the rack.
12. Position a rail assembly (middle and outer rails) with its black plastic end caps toward the rear of the rack and its outer rail closest to the brackets.
13. Align the front screw hole in the outer rail with the threaded hole nearest the front of the front bracket and fit the rail assembly into the front and rear brackets.
14. Slide the middle rail toward the front until the access hole in the middle rail is aligned with the front screw hole in the outer rail.
15. Insert screw through the access hole and loosely attach the outer rail to the front bracket.
16. In a similar manner to steps 13 through 15, install a screw through a slot in the outer rail and into the rear-most threaded hole in the front bracket. Firmly tighten this screw.
17. Firmly tighten the front screw installed loosely in step 15.
18. In the same manner, attach the other rail assembly to the other side.
19. Slide the middle rail toward the front until the rear bracket area is accessible.
20. Attach the rear end of the outer rail to the rear bracket with at least one screw. If possible, attach at two places.
21. In the same manner, attach the other rail assembly to the other side.
26 Intel® Server System SR2500AL User’s Guide
22. Fully extend the left and right rails until the extension locks have engaged and the rails will not push back in. The rail system is now ready to receive the chassis.
Caution: Lifting and placing the chassis in the rails is a two-person job. If needed, use an appropriate lifting device.
23. With the chassis front facing you, lift the chassis and carefully insert the rails attached to the chassis in the extended rails.
24. Slide the chassis toward the rear of the cabinet until the rails lock together.
25. Depress and hold down the finger tabs on both extension locks while sliding the chassis toward the rear.
26. Slide the chassis all the way into the rack until the chassis handles are against the front posts.
Basic Rail Rack Mount Removal
1. Disconnect all cables from the back of the system.
Note: Remember to use the system LED to properly identify the system you are servicing.
2. Pull system from rack until brackets are fully extended.
3. Push in both clips on the brackets and slide the system forward until the inner rail separates from the outer rail.
4. Remove and service the system.
Basic Rail Rack Mount Installation
1. Extend the inner rail until it locks.
2. Depress the spring safety lock to release the inner rail.
3. Remove the inner rail from the rail assembly.
4. Attach the outer rail slides to the rack posts using two #10-32 x 1/2 screws at the front posts, and two #10-32 x 1/2 screws at the rear posts.
Note: The rail flanges mount to the inside of each post.
5. Insert the inner rails over the server chassis sidewall studs.
6. Slide the inner rails toward the front of the server chassis.
7. Secure the inner rails with one #6-32 x 1/4 screw for each rail.
8. Align the inner rails (attached to the server chassis) with the outer rail assemblies
(attached to the rack).
9. Engage the matching rails and slide the server chassis into the rack until the two safety stops lock into position.
10. Depress the two safety locks (one on each side).
Intel® Server System SR2500AL User’s Guide 27
11. Slide the server chassis all the way into the rack.
12. Use the rack screws (#10-32 x 3/4) to secure the chassis and rack handles into the rack.
Tool-less Rail Rack Mount Servicing
1. To service the system, pull the system out from the rack.
2. Disconnect the power cable(s) and proceed with servicing the system.
3. When the servicing is completed, re-connect the power cable(s).
4. Pull up on the green tabs on each rail and slide the system back into the rack.
Note: Beware of cables when re-installing the system into the rack so that the cables do not get pulled or interfered with.
Removing and Installing the Front Bezel
The front bezels are available as optional accessories for the Intel
SR2500ALLX and/or the Intel
®
®
Server System
Server System SR2500ALBRP. Two front bezel options are available. One is used for the standard control panel and the other is used with the
Intel
®
Local Control Panel. See the diagrams below to identify your front bezel. Note the orientation in the figures below - the control panel is at the right. If you are installing a bezel on your server system, make sure you position it as shown.
AF000154
Figure 16. Front Bezel Supporting the Standard Control Panel
28
AF000153
Figure 17. Front Bezel Supporting the Intel
®
Local Control Panel
Intel® Server System SR2500AL User’s Guide
Removing the Front Bezel
Use the steps below if your system includes a front bezel.
1. Unlock the bezel.
2. Disconnect any cables attached to the control panel.
3. Pull the bezel from the server system.
TP02129
Figure 18. Removing the Front Bezel
Intel® Server System SR2500AL User’s Guide 29
Installing the Front Bezel
Use the steps below if your system includes either the standard front bezel or the front bezel for the Intel
®
Local Control Panel. The front bezel is optional.
1. At each end of the bezel, line up the center notch on the bezel with the center guide on the rack handles.
2. Push the bezel onto the front of the server system until it clicks into place.
3. Connect any necessary cables to the front control panel area at the right side of the server system.
TP02130
Figure 19. Installing the Front Bezel
Removing and Installing the System Cover
Removing the System Cover
The server system must be operated with the chassis cover in place to ensure proper cooling. You will need to remove the top cover to add or replace components inside of the server. Before removing the chassis cover, power down the server and unplug all peripheral devices and the AC power cable(s).
Note: A nonskid surface or a stop behind the server system may be needed to prevent the server system from sliding on your work surface.
30 Intel® Server System SR2500AL User’s Guide
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord(s).
4. Remove the safety screw if it is installed. See letter "A" in the figure below.
5. While holding in the blue button at the top of the server system in (see letter "B"), slide the top cover back until it stops (see letter "C").
6. Insert your finger in the notch (see letter “D”) and lift the cover upward to remove it.
D
A
C
B
Figure 20. Removing the Server System Cover
TP02127
Installing the Server System Cover
1. Place the cover over the server system so that the side edges of the cover sit just inside the server system sidewalls.
2. Slide the cover forward until it clicks into place (see letter “A”).
3. (Optional) Insert the safety screw at the center of the top cover (see letter “B”) if required.
4. Reconnect all peripheral devices and the AC power cord(s).
Intel® Server System SR2500AL User’s Guide 31
B
A
TP02128
Figure 21. Installing the Server System Cover
Removing and Installing the Processor Air Duct
Always operate your server system with the processor air duct in place. The air duct is required for proper airflow within the server system.
For instructions on adding or replacing a processor, first remove the processor air duct, and then see your server board user guide for instructions on processor installations and removals. Return to these instructions to reinstall the processor air duct after installing your processor and heat sink.
Removing the Processor Air Duct
1. Observe the safety and ESD precautions at the beginning of this book. See " “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable.
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Lift the processor air duct from its location over the two processor sockets.
32 Intel® Server System SR2500AL User’s Guide
Figure 22. Removing the Processor Air Duct
TP02131
Intel® Server System SR2500AL User’s Guide 33
Installing the Processor Air Duct
1. Observe the safety and ESD precautions at the beginning of this book. See " “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Turn processor air duct over to reveal underside (see letter “A”).
5. If two processors are installed: remove air dam (see letter “B”) by sliding slotted holes off duct pins.
Notes: Do not remove the air dam if only one processor is installed.
Do not remove memory air deflector.
B
A
TP02133
Figure 23. Removing the Processor 2 Air Dam (Optional - only if two processors are installed)
6. Place the processor air duct over the processor socket(s). See the figure below. The front edge of the air duct should contact the fan module. Use caution not to pinch or disengage cables that may be near or under the air duct.
7. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
8. Plug all peripheral devices and the AC power cable(s) into the server.
34 Intel® Server System SR2500AL User’s Guide
Figure 24. Installing the Processor Air Duct
TP02132
Installing and Removing Memory
The silkscreen on the board for the DIMMs displays DIMM A1, DIMM A2, DIMM B1,
DIMM B2, DIMM C1, DIMM C2, DIMM D1 and DIMM D2 starting from the center of the board. See "Memory" for a discussion of the memory requirements and options. See
“Server System References” for a link to the list of tested DIMMs.
Installing DIMMs
To install DIMMs, follow these steps:
1. Observe the safety and ESD precautions in “Safety Information” .
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord(s) from the server.
4. Remove the server's cover. See the documentation that came with your server chassis for instructions on removing the server's cover.
5. Locate the DIMM sockets (see Figure 25 ).
Intel® Server System SR2500AL User’s Guide 35
A
D
C
B
DIMM B2
Socket
DIMM B1
Socket
DIMM A2
Socket
DIMM A1
Socket
DIMM C1
Socket
DIMM C2
Socket
DIMM D1
Socket
DIMM D2
Socket
36
TP02072
Figure 25. Installing the Memory
6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (see letter “A” in the figure above).
7. Holding the DIMM by the edges, remove it from its anti-static package.
8. Position the DIMM above the socket. Align the notch on the bottom edge of the
DIMM with the key in the DIMM socket. The arrow in the inset in Figure 7 is pointing to the key in the socket (see letter “B” in the figure above).
9. Insert the bottom edge of the DIMM into the socket.
10. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place (see letter “C” in the figure above). Make sure the clips are firmly in place (see letter “D” in the figure above).
Intel® Server System SR2500AL User’s Guide
11. Replace the server's cover and reconnect the AC power cord(s). See the documentation that came with your server chassis for instructions on installing the server's cover.
Removing DIMMs
To remove a DIMM, follow these steps:
1. Observe the safety and ESD precautions in “Safety Information” .
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Remove the AC power cord(s) from the server.
4. Remove the server's cover. See the documentation that came with your server chassis for instructions on removing the server's cover.
5. Gently spread the retaining clips at each end of the socket. The DIMM lifts from the socket.
6. Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static package.
7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets.
8. Replace the server's cover and reconnect the AC power cord(s). See the documentation that came with your server chassis for instructions on installing the server's cover.
Installing or Replacing the Processor
Caution: Processor must be appropriate: You may damage the server board if you install a processor that is inappropriate for your server. See “Server System References” for a link to the list of compatible processor(s).
Caution: ESD and handling processors: Reduce the risk of electrostatic discharge (ESD) damage to the processor by doing the following: (1) Touch the metal chassis before touching the processor or server board. Keep part of your body in contact with the metal chassis to dissipate the static charge while handling the processor. (2) Avoid moving around unnecessarily.
Caution: Protective socket cover needs to be removed for proper cooling of the processor; failure to remove the cover could result in damage to the system.
Installing the Processor
To install a processor, follow these instructions:
1. Observe the safety and ESD precautions in “Safety Information” .
2. Turn off all peripheral devices connected to the server. Turn off the server.
Intel® Server System SR2500AL User’s Guide 37
3. Disconnect the AC power cord(s) from the server.
4. Remove the server's cover. See the documentation that came with your server chassis for instructions on removing the server's cover.
5. Locate the processor socket and raise the socket handle completely (see Figure 26 ).
TP02074
Figure 26. Lifting the Processor Socket Handle
6. Raise the CPU load plate (see Figure 27 ).
A B
38
TP02075
Figure 27. Installing the Processor
Note: Do not touch the socket pins; they are very sensitive and easily damaged.
7. Line up the alignment marks on the processor and the socket, and insert the processor into the socket.
Note: Make sure the alignment triangle mark and the alignment triangle cutout align correctly.
8. Remove the protective socket cover (see Figure 28 ).
Note: Retain the protective socket cover for use when removing a processor that will not be replaced.
Intel® Server System SR2500AL User’s Guide
A
B
TP02076
Figure 28. Removing the Socket Cover
9. Lower the CPU load plate and lower the socket lever completely.
Installing the Heat Sink(s)
The heat sink has Thermal Interface Material (TIM) located on the bottom of it. Use caution when you unpack the heat sink so you do not damage the TIM.
1. Set the heat sink over the processor, lining up the four captive screws with the four posts surrounding the processor.
2. Loosely screw in the captive screws on the heat sink corners in a diagonal manner.
Do no fully tighten one screw before tightening another.
3. Gradually and equally tighten each captive screw until each is firmly tightened.
2
3
4
1
TP02077
Figure 29. Installing the Heat Sink (2U Passive Heat Sink Shown)
Intel® Server System SR2500AL User’s Guide 39
4. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.
5. Replace the server's cover and reconnect the AC power cord(s). See the documentation that came with your server chassis for instructions on installing the server's cover.
Removing a Processor
1. Observe the safety and ESD precautions in “Safety Information” .
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Remove the AC power cord(s) from the server.
4. Remove the server's cover. See the documentation that came with your server chassis for instructions on removing the server's cover.
5. Unplug the processor fan cable from the server board.
6. Loosen the four captive screws on the corners of the heat sink.
7. Twist the heat sink slightly to break the seal between the heat sink and the processor.
8. Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink again. Do not force the heat sink from the processor. Doing so could damage the processor.
9. Lift the processor lever.
10. Raise the CPU load plate.
11. Remove the processor.
12. If installing a replacement processor, see “Installing the Processor” . Otherwise, install the protective socket cover over the empty processor socket and reinstall the chassis cover.
Removing and Installing the Small Air Baffle
Some installation processes will require that you remove the small air baffle that is placed behind the hard drive bays, near the front of your server. The steps below describe how to remove and then install the small air baffle. Use these steps only when it is indicated as necessary for a component installation process.
Always operate your server system with the small air baffle in place. The small air baffle is required for proper airflow within the server system.
40 Intel® Server System SR2500AL User’s Guide
Removing the Small Air Baffle
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Pull up and out on the air baffle to remove it. See the figure below.
Figure 30. Removing the Small Air Baffle
Installing the Small Air Baffle
1. Lower the baffle into the server system.
2. Snap the baffle into place as shown in the figure below.
TP02136
Intel® Server System SR2500AL User’s Guide 41
TP02137
Figure 31. Installing the Small Air Baffle
3. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
4. Plug all peripheral devices and the AC power cable(s) into the server.
Removing and Installing the Large Air Baffle
Some installation processes will require that you remove the large air baffle that is placed behind the hard drive bays, next to the fan module near the front of your server. The steps below describe how to remove and then install the large air baffle. Use these steps only when it is indicated as necessary for a component installation process.
Always operate your server system with the large air baffle in place. The large air baffle is required for proper airflow within the server system.
Removing the Large Air Baffle
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Note how the cables are routed over and under the air baffle (if any). You will need to re-route these cables.
42 Intel® Server System SR2500AL User’s Guide
5. Pull up on the air baffle to remove it. See the figure below. You may need to remove or hold cables out of the way.
Figure 32. Removing the Large Air Baffle
TP02134
Installing the Large Air Baffle
1. Lower the baffle into the server system and snap into the server board standoff as shown in the figure below.
2. While setting the baffle into place, route the cables beneath it appropriately. See
Appendix , “Cable Routing” or the Quick Reference Label that came with your system for help in determining where the cables should be routed.
Intel® Server System SR2500AL User’s Guide 43
TP02134
Figure 33. Installing the Large Air Baffle
3. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
4. Plug all peripheral devices and the AC power cable(s) into the server.
Installing and Removing a Hot-swap Hard Drive
Up to six hot-swap SAS or SATA drives can be installed.
Cautions: If you install less than six drives or devices, empty drive bays must be occupied by carriers with baffles to maintain proper system cooling.
To avoid possible damage to your server system, do not use older style drive carriers.
Note: The server system does not support all hard drives. See “Server System References“ for an Internet link to a list of supported hardware.
Installing a SAS or SATA Hot-swap Hard Disk Drive
1. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
2. Open the latch at the front of the hard drive carrier. See letter "A" in the figure below.
44 Intel® Server System SR2500AL User’s Guide
3. Pull out on the black lever and slide the carrier from the server system. See letter
"B" in the figure below.
B
A
TP02141
Figure 34. Removing Hot-swap Disk Carrier from the Server System
4. Remove the four screws that attach the plastic retention device or the previously installed hard drive to the drive carrier. Two screws are at each side of the retention device or the hard drive. Store the plastic retention device for future use.
B
A
TP02142
Figure 35. Removing Retention Device from Drive Carrier
5. Remove the hard drive from its wrapper and place it on an antistatic surface.
6. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions.
7. With the drive circuit-side down, position the connector end of the drive so that it is facing the rear of the drive carrier.
8. Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the screws that were attached to the plastic retention device.
Intel® Server System SR2500AL User’s Guide 45
46
B
A
B
TP02143
Figure 36. Installing Hard Drive into Carrier
9. With the black lever in the fully open position, slide the drive assembly into the server system. The green latch at the front of the drive carrier must be to the right.
Do not push on the black drive carrier lever until the lever begins to close by itself.
10. When the black drive carrier lever begins to close by itself, push on it to lock the drive assembly into place.
B
A
TP02144
Figure 37. Install Drive Assembly into the Server System
11. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
12. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
13. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide
Removing a SAS or SATA Hot-swap Hard Disk Drive
1. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
2. Press in on the green latch at the front of the hard drive carrier.
3. Pull out on the black lever to slide the carrier from the server system.
4. Remove the four screws that attach the hard drive to the drive carrier. Lift the drive from the carrier. Store the drive in an anti-static bag.
5. If you are not installing a new drive, place the plastic retention device into the drive carrier, using the four screws you removed from the hard drive.
6. Insert the screws that held the drive in the carrier into the screw locations on the carrier for future use.
7. With the black lever in the fully open position, slide the drive carrier into the server system. The green latch must be to the right. Do not push on the black lever until the lever begins to close by itself.
Note: For proper airflow, the hard drive carrier must be replaced in the server system, even if no hard drive is installed in it.
8. When the black lever begins to close by itself, push on it to lock the drive carrier into place.
9. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
10. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
11. Plug all peripheral devices and the AC power cable(s) into the server.
Installing or Removing a Slimline Optical Drive or Internal USB Floppy
Cautions: Slimline optical drives are NOT hot swappable. Before removing or replacing the drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet.
To maintain proper system cooling, a filler blank must be installed if you do not install a device at this location.
Intel® Server System SR2500AL User’s Guide 47
Installing a Slimline Optical Drive or Internal USB Floppy
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
4. Remove the server system cover. For instructions, see “Removing the System
Cover” .
5. Insert the interposer board into the optical drive.
6. Obtain the optical drive and the drive tray.
7. Align the two holes on the left edge of the optical drive and interposer board with the two metal tabs in the tray as shown in Figure 38 (see letter “A”).
8. Lower the opposite side of the optical drive into the tray until it clicks into place
(see letter “B”).
A
48
B
TP02147
Figure 38. Installing an Optical Drive into the Drive Tray
9. Screw the interposer board into the carrier.
10. Insert the optical drive tray assembly into the server system as shown in Figure 39
(see letter “A”).
11. Make sure that the back end of the interposer board plugs into the matching socket on the backplane (see letter “B”).
12. Verify that the blue release lever on the tray locks into place.
13. (Optional) For installing the optional USB floppy drive, note the location of the backplane USB connector in Figure 39 (see letter “C”) and refer to the documentation that came with the device.
Intel® Server System SR2500AL User’s Guide
B
C
A
TP02149
Figure 39. Installing an Optical Drive Assembly into the Server System
14. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
15. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
16. Plug all peripheral devices and the AC power cable(s) into the server.
Removing a Slimline Optical Drive or Internal USB Floppy
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
4. Remove the server system cover. For instructions, see “Removing the System
Cover” .
5. If removing an internal USB floppy drive, unplug it from the backplane.
6. Press the blue release lever (see letter “A”) to unlock the optical drive tray and remove the slimline optical drive tray assembly from the server system as shown in
Figure 40 .
Intel® Server System SR2500AL User’s Guide 49
A B
C
50
AF000151
Figure 40. Removing the Slimline Optical Drive Assembly from the Server
System
7. Press downward on the side of the tray (see letter “A”) and disengage the drive from the two metal tabs on the opposite side of the tray (see letter “B”).
8. Lift up on the optical drive (see letter “C”) to remove it from the tray.
C
B
A
AF000152
Figure 41. Removing the Slimline Optical Drive from the Tray
Intel® Server System SR2500AL User’s Guide
9. If no device will be installed in this location, install a filler blank as shown in
Figure 42 .
A
AF000155
Figure 42. Installing Filler Blank into the Server System
10. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
11. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
12. Plug all peripheral devices and the AC power cable(s) into the server.
Installing a Tape Drive
To install a tape drive into your server system, your system must meet the following requirements:
• You must purchase the tape drive kit, order number ADRTAPEKIT.
• You must purchase a 3.5-inch tape drive.
• You must have an add-in card that supports a tape drive.
After purchasing the tape drive kit and the tape drive, use the instructions below to install them. In addition to these instructions, refer to the instructions that came with your tape drive for additional requirements.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
Intel® Server System SR2500AL User’s Guide 51
4. Remove the server system cover. For instructions, see “Removing the System
Cover” .
5. Remove the tape drive filler panel from the server system by using a long screwdriver to push it out from the inside of the server system. See the figure below to locate the tape drive filler panel.
AF000036
Figure 43. Removing Tape Drive Filler Panel from the Server System
6. Remove the hard drive blank that is installed in the sixth drive bay. See the figure below to locate the sixth drive filler panel.
52
AF000035
Figure 44. Removing Sixth Drive Filler Panel from the Server System
Intel® Server System SR2500AL User’s Guide
7. Attach the tape drive to the tape drive carrier kit using the four screws that were included with the tape drive kit. See the figure below.
A
B
AF000032
Figure 45. Inserting a Tape Drive into the Carrier
8. Slide the tape drive carrier with the installed tape drive into the combined tape drive bay/sixth drive bay until the carrier clicks into place.
AF000033
Figure 46. Installing Tape Drive Assembly into the Server System
Intel® Server System SR2500AL User’s Guide 53
9. See the documentation that came with your tape drive for data cable connection information.
10. Connect the 4-pin tape power cable to the tape drive.
11. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
12. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
13. Plug all peripheral devices and the AC power cable(s) into the server.
Installing a Sixth Hard Drive
Use the instructions below to install a hard drive in the sixth hard drive bay.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
4. Remove the server system cover. For instructions, see “Removing the System
Cover” .
5. Slide the sixth HDD bracket into the backplane as shown in the figure below.
54
Figure 47. Installing Sixth HDD Bracket
AF000012
Intel® Server System SR2500AL User’s Guide
6. The sixth hard drive kit comes with a power cable and two SATA cables. Cabling for the sixth hard drive varies depending on which mid-plane you have in your system. If you have an active mid-plane in your system, go to step 7 for cabling instructions. If you have a passive mid-plane in your system, go to step 8 for cabling instructions.
7.
If you have an active mid-plane in your system, install the power cable to the backplane and the sixth HDD board (see letter “A”). Install the short SATA cable to the backplane and the sixth HDD board (see letter “B”). Proceed to step 9.
A
B
AF002122
Figure 48. Installing Power and SATA Cables (Active Mid-Plane Installed)
Note: You will not use the long SATA cable from the 6th HDD kit in a system with an active midplane.
Intel® Server System SR2500AL User’s Guide 55
8.
If you have a passive mid-plane installed in your system, install the power cable to the backplane and the sixth HDD board (see letter “A”). Install one end of the long SATA cable (labeled HSBP/TAPE) to the sixth HDD board (see letter “B”) and route the cable through the air baffle as shown (see letter “C”). Connect the other end of the cable (labeled SERVER BOARD) to the SATA5 connector on the server board (see letter “D” in the figure below). Continue with step 9.
C
D
56
A
B
AF002122
Figure 49. Installing Power and SATA Cables (Passive Mid-Plane Installed)
Note: You will not use the short SATA cable from the 6th HDD kit in a system with a passive midplane.
9. Install a hard drive into the sixth hard drive bay. For instructions, see “Installing a
SAS or SATA Hot-swap Hard Disk Drive” .
10. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
11. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
12. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide
Filling Empty Server System Bays
A filler panel, drive blank, or empty drive carrier must be installed into an empty drive bay. To access the drive bays, remove the front bezel if it is installed. For instructions, see
“Removing the Front Bezel” . With the bezel removed, install the appropriate panel(s), blank, or empty hard drive bay(s) as described below.
• If you do not have an optical drive installed in the slimline bay, install the slimline filler panel. See letter “A” in the figure below.
• If you do not have a tape drive installed, install a filler panel into the empty slot above the sixth drive bay. See letter “B” in the figure below.
• If you do not have a sixth drive or a tape drive installed, install the drive bay blank into the sixth drive bay. See letter “C” in the figure below.
• Install empty hard drive carriers into any remaining empty hard drive bays.
A
B
C
Figure 50. Installing the Filler Panels
AF000011
Installing and Removing the PCI Riser Assembly
Removing the PCI Riser Assembly
To remove the PCI riser assembly, use the following instructions.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
Intel® Server System SR2500AL User’s Guide 57
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct by lifting straight up.
5. Disconnect any cables attached to any add-in cards.
6. Grasp both riser latches with thumb and forefinger (see letter “A”), and pull up to release riser assembly.
7. Lift riser assembly straight up (see letter “B”).
B
A
58
TP02145
Figure 51. Removing PCI Riser Assembly from the Server System
8. If you need to add or replace a PCI add-in card, see “Installing and Removing a PCI
Add-in Card” .
9. If you need to add or replace a PCI riser connector, see “Replacing a PCI Riser
Card” .
10. If you removed the PCI riser assembly for another procedure, continue with that procedure.
Intel® Server System SR2500AL User’s Guide
Installing the PCI Riser Assembly
1. Lower the riser assembly into place (see letter “A”).
2. Align the three hooks in the riser assembly with the matching slots at the back of the server system (see letter “B”).
A
B
TP02146
Figure 52. Installing PCI Riser Assembly into the Server System
3. Press down uniformly until the three hooks on the rear of the PCI riser assembly engage the server system back panel slots. The riser cards will seat into the matching sockets on the server board.
4. Connect any cables to add-in cards that require them. See your add-in card documentation for information and add-in card requirements.
5. Re-install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
6. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
7. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
8. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 59
Replacing a PCI Riser Card
Caution: PCI riser connectors are NOT hot swappable. Before removing or replacing the riser connector, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the
AC power cord from the system or wall outlet.
Note: To eliminate the possibility of installing the replacement connector on the wrong side of the PCI riser assembly, replace one connector at a time.
Removing a PCI Riser Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Disconnect any cables attached to any add-in cards.
6. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
7. Remove any add-in cards from the PCI riser connector. For instructions, see
“Removing a PCI Add-in Card” .
8. Push back on the blue release lever at the end of the riser connector (see letter “A” in the figure below).
9. While holding the lever back, push firmly on the edge of the board, sliding it toward the right of the riser module, to disengage the connector from the riser pins
(see letter “B” in the figure below) and remove from the server system (see letter
“C” in the figure below).
60 Intel® Server System SR2500AL User’s Guide
A
B
C
AF000326
Figure 53. Removing the PCI Riser Card from the Server System (Full Height
Side)
10. Install the replacement riser connector, if desired. For instructions, see “Installing
PCI Riser Card into the Server System” .
11. Install the PCI add-in card(s) if desired. For instructions, see “Installing a PCI Addin Card” .
12. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
13. Connect any cables to add-in cards that require them. See your add-in card documentation for information and add-in card requirements.
14. Re-install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
15. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
16. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 61
Installing a PCI Riser Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Disconnect any cables attached to any add-in cards.
6. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
7. Remove any add-in cards from the PCI riser connector. For instructions, see
“Removing a PCI Add-in Card” .
8. Press the hold the blue riser locking lever (see letter “A” in the figure below).
9. Place riser connector onto retention pins.
10. Slide the riser connector to the left of the riser module to lock it into place (see letter “B” in the figure below).
A
B
62
AF000147
Figure 54. Installing PCI Riser Card into the Server System
11. Release the blue locking lever.
Intel® Server System SR2500AL User’s Guide
12. Install the PCI add-in card(s) if desired. For instructions, see “Installing a PCI Addin Card” .
13. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
14. Connect any cables to add-in cards that require them. See your add-in card documentation for information and add-in card requirements.
15. Re-install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
16. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
17. Plug all peripheral devices and the AC power cable(s) into the server.
Installing and Removing a PCI Add-in Card
The instructions below describe how to install and remove a PCI add-in card.
Installing a PCI Add-in Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
6. Open the rear retention clip by pushing the blue slide upward and rotating clip to the fully open position (see letter “A”).
7. Open the front retention clip by rotating 90 degrees outward (see letter “B”).
8. Remove the filler panel from the selected add-in card slot (see letter “C”).
9. Insert add-in card until it seats in riser card connector (see letter “D”).
Intel® Server System SR2500AL User’s Guide 63
C
A
D
B
AF000148
Figure 55. Installing a Full Height Add-In Card
10. Close both retention clips.
Note: Make sure that all empty add-in card slots have filler panels installed.
11. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
12. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
13. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
14. Plug all peripheral devices and the AC power cable(s) into the server.
Removing a PCI Add-in Card
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
64 Intel® Server System SR2500AL User’s Guide
6. Open the rear retention clip by pushing the blue slide upward and rotating clip to the fully open position (see letter “A”).
7. Open the front retention clip by rotating 90 degrees outward (see letter “B”).
8. Remove the PCI add-in card from the riser card connector (see letter “C”).
D
A
C
B
AF000327
Figure 56. Removing a Full Height Add-In Card
9. Close both retention clips.
Note: Make sure that all empty add-in card slots have filler panels installed.
10. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
11. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
12. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
13. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 65
Installing and Removing the I/O Expansion
Module(s)
Installing the I/O Expansion Module(s)
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
5. Squeeze the sides of the I/O expansion module cover(s) to disengage it from the server system back panel and remove it. See letter “A” in the figure below.
6. Attach the standoffs to the server board (see letter “B” in the figure below) and attach the I/O expansion module(s) to the server board (see letter “C” in the figure below).
I/O Module
(Dual Gigabit)
I/O Module
(External SAS)
B
C
66
A
AF000740
Figure 57. Installing the I/O Expansion Module to the Server Board
7. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
8. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
9. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
10. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide
Removing the I/O Expansion Module(s)
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
5. Remove the I/O expansion module(s) from the server board (see letter “A” in the figure below).
6. Remove the standoffs from the server board (see letter “B” in the figure below).
7. Install the I/O expansion module cover(s) into the system back panel (see letter “C” in the figure below).
B
A
C
AF00074 3
Figure 58. Removing the I/O Expansion Module(s) from the Server Board
8. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
9. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
10. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
11. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 67
Installing and Removing the Intel
®
Management Module and the Intel
Remote
®
RMM NIC
Installing the Intel
®
RMM and Intel
®
RMM NIC
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
5. Squeeze the sides of the Intel
®
RMM NIC module cover to disengage it from the server system back panel and remove it. See letter “A” in the following figure.
6. A self-adhesive foam gasket is required to protect the underside of the NIC module.
Remove the backing paper from the spacer and install as illustrated (see letter “B” in the following figure).
7. Attach the standoffs to the server board (see letter “C” in the following figure) and attach the Intel
®
RMM NIC module to the server board (see letter “D” in the following figure).
8. Insert the standoff into the hole labeled TH4 on the Intel
“E” in the following figure). The standoff installs on the bottom side of the Intel
RMM board.
®
RMM board (see letter
®
68 Intel® Server System SR2500AL User’s Guide
1. Attach the Intel ® RMM board to the server board connector and snap the standoff into the matching hole on the server board (see letter “F” in the following figure).
B
A
E
D
F
C
AF000741
Figure 59. Installing the Intel
®
RMM and the Intel
®
RMM NIC Module to the
Server System
2. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
3. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
4. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
5. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 69
Removing the Intel
®
RMM and Intel
®
RMM NIC
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
5. Remove the Intel
® below).
RMM board from the server board (see letter “A” in the figure
6. Remove the Intel
® figure below).
RMM NIC module from the server board (see letter “B” in the
7. Remove the standoffs from the server board (see letter “C” in the figure below).
8. Install the Intel
®
RMM NIC module cover into the system back panel (see letter
“D” in the figure below).
70
A B
C
D
AF000744
Figure 60. Removing the Intel
®
RMM and the Intel
®
RMM NIC Module from the Server System
9. Install the PCI riser assembly into the server system. For instructions, see
“Installing the PCI Riser Assembly” .
10. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
11. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
12. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide
Replacing the Mid-plane Board
The instructions below describe how to replace the mid-plane board.
Removing the Mid-plane Board
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Disconnect all cables from the mid-plane board.
5. Remove the bridge board by lifting the retention mechanism from the mid-plane and the server board (see letter “A” in the figure below), and lifting straight up (see letter “B” in the figure below) and sliding the board out of the fan assembly (see letter “C” in the figure below).
A
B
B
C
A
AF000164
Figure 61. Removing the Bridge Board from the Server System
6. Remove the fan module. For instructions, see “Replacing a Fan Module” .
7. Hold the mid-plane board only by the edges. Slide the mid-plane board back to release it from the backplane (see letter “A” in the figure below).
Intel® Server System SR2500AL User’s Guide 71
8. Lift the mid-plane board over the retention pins (see letter “B” in the figure below) and out of the server system.
A
B
AF000014
Figure 62. Removing the Mid-plane from the Server System
Installing the Mid-plane Board
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Position the mid-plane board over the retention pins as shown in the figure below
(see letter “A”).
5. Slide the mid-plane board forward (see letter “B”) and insert the mid-plane into the backplane connector as shown.
72 Intel® Server System SR2500AL User’s Guide
A
B
AF000015
Figure 63. Installing the Mid-plane into the Server System
6. Connect cables as necessary to the mid-plane board.
7. Install the fan module. For instructions, see “Replacing a Fan Module” .
8. Install the bridge board by opening the retention mechanism (see letter “A” in the figure below), sliding the board through the fan assembly (see letter “B” in the figure below), and inserting it into the connector on the server board (see letter “C” in the figure below. Close the retention mechanism to hold the bridge board in place.
A
C
B
C
A
AF000163
Figure 64. Installing the Bridge Board into the Server System
Intel® Server System SR2500AL User’s Guide 73
9. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
10. Plug all peripheral devices and the AC power cable(s) into the server.
Replacing the Backplane
The instructions below describe how to replace the backplane.
Removing the Backplane
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the mid-plane board. For instructions, see “Removing the Mid-plane
Board” .
Note: To prevent damage to your system, you must ensure the mid-plane is completely removed before attempting to remove the backplane.
5. Remove all hot-swap drive carriers, regardless of whether a drive is installed in the carrier. For instructions, see “Removing a SAS or SATA Hot-swap Hard Disk
Drive” .
6. Disconnect all cables from the backplane.
7. Firmly grasp the top of the backplane and remove the backplane from the server system by pulling straight up as shown in the figure below.
74 Intel® Server System SR2500AL User’s Guide
AF000016
Figure 65. Removing the Backplane from the Server System
Intel® Server System SR2500AL User’s Guide 75
Installing the Backplane
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the mid-plane board. For instructions, see “Removing the Mid-plane
Board” .
5. Remove all hot-swap drive carriers, regardless of whether a drive is installed in the carrier. For instructions, see “Removing a SAS or SATA Hot-swap Hard Disk
Drive” .
6. Hold the backplane only by the edges. Do not push or pull on any components on the backplane. set the backplane in place at the front of the server system, with the sides of the board resting in the guides at the left and right sides of the server system.
7. Slide the backplane into the server system guides at the left and right sides of the server system until the pins at the left and right sides of the backplane bracket are fully inserted into the matching holes in the server system (see letters “A” and “B”).
A
B
76
AF000017
Figure 66. Installing the Backplane into the Server System
8. Install hot-swap drive carriers. For instructions, see “Installing a SAS or SATA
Hot-swap Hard Disk Drive” .
9. Install the mid-plane board. For instructions, see “Installing the Mid-plane Board” .
Intel® Server System SR2500AL User’s Guide
10. Connect necessary cables to the backplane.
11. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
12. Plug all peripheral devices and the AC power cable(s) into the server.
Installing and Removing the RAID Activation
Key and the RAID Mini DIMM
Installing the RAID Activation Key and the RAID Mini DIMM
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
5. Install the RAID activation key by pushing straight down (see letter “A” in the figure below).
6. Install the RAID mini DIMM by releasing the retention mechanism (see letter “B” in the figure below) and inserting the DIMM into the socket (see letter “C” in the figure below).
A B
B C
AF000742
Figure 67. Installing the RAID Activation Key and the RAID Mini DIMM
Intel® Server System SR2500AL User’s Guide 77
7. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
8. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
9. Plug all peripheral devices and the AC power cable(s) into the server.
Removing the RAID Activation Key and the RAID Mini DIMM
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
5. Remove the RAID activation key by lifting straight up (see letter “A” in the figure below).
6. Remove the RAID mini DIMM by releasing the retention mechanism (see letter
“B” in the figure below) and pulling the DIMM out of the socket (see letter “C” in the figure below).
78
A B
B C
AF000745
Figure 68. Removing the RAID Activation Key and the RAID Mini DIMM
7. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
8. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
9. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide
Installing and Removing the RAID Battery
Backup Unit (BBU)
Installing the RAID Battery Backup Unit
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
5. Insert the RAID battery backup unit into the server system and slide back until it locks into place as shown in the figure below (see letter “A”).
6. Attach the cable from the rear of the RAID battery backup unit to the mid-plane board as shown (see letter “B”).
A
B
AF000149
Figure 69. Installing the RAID Battery Backup Unit
7. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
8. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
Intel® Server System SR2500AL User’s Guide 79
9. Plug all peripheral devices and the AC power cable(s) into the server.
Removing the RAID Battery Backup Unit
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
5. Remove the cable from the rear of the RAID battery backup unit and the mid-plane board as shown in the figure below (see letter “A”).
6. Slide the RAID battery backup unit forward and lift from the server system (see letter “B”).
B
A
80
AF000150
Figure 70. Removing the RAID Battery Backup Unit
7. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
8. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
9. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide
Installing and Removing the Server Board
Installing the Server Board
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
6. Remove the optical drive cable if installed.
7. Remove the bridge board. For instructions, see Figure 61 “Removing the Bridge
Board from the Server System” on page -71 .
8. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
9. Remove the fan module assembly. For instructions, see “Replacing a Fan Module” .
10. Place the server board into the server system as shown in the figure below (see letter “A”), and attach the server board with six screws (see letter “B”).
B
A
AF000025
Figure 71. Installing the Server Board
Intel® Server System SR2500AL User’s Guide 81
11. Connect all power cables to the server board.
12. Install memory. For instructions, see “Installing DIMMs” .
13. Install processor(s). For instructions, see “Installing the Processor” .
14. Install the fan module assembly. For instructions, see “Replacing a Fan Module” .
15. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
16. Install the bridge board. For instructions, see Figure 64 “Installing the Bridge
Board into the Server System” on page -73 .
17. Install the optical drive cable (optional).
18. Install the PCI riser assembly. For instructions, see “Installing the PCI Riser
Assembly” .
19. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
20. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
21. Plug all peripheral devices and the AC power cable(s) into the server.
Removing the Server Board
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
6. Remove the optical drive cable if installed.
7. Remove the bridge board. For instructions, see Figure 61 “Removing the Bridge
Board from the Server System” on page -71 .
8. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
9. Remove the fan module assembly. For instructions, see “Replacing a Fan Module” .
10. Disconnect all cables from the server board.
11. Remove memory. For instructions, see “Removing DIMMs” .
12. Remove the processor(s). For instructions, see “Removing a Processor” .
82 Intel® Server System SR2500AL User’s Guide
13. Remove the six screws from the server board (see letter “A”) and lift the server board from the server system (see letter “B”).
A
B
Figure 72. Removing the Server Board
AF000026
14. Replace the server board. For instructions, see “Installing the Server Board” .
15. Connect all power cables to the server board.
16. Install the fan module assembly. For instructions, see “Replacing a Fan Module” .
17. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
18. Install the bridge board. For instructions, see Figure 64 “Installing the Bridge
Board into the Server System” on page -73 .
19. Install the optical drive cable (optional).
20. Install the PCI riser assembly. For instructions, see “Installing the PCI Riser
Assembly” .
21. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
22. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
23. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 83
Replacing the Backup Battery
The lithium battery on the server board powers the RTC for up to 10 years in the absence of power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) may be wrong. Contact your customer service representative or dealer for a list of approved devices.
Warning: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions.
Advarsel: Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.
Advarsel: Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren.
Varning: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.
Varoitus: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
84 Intel® Server System SR2500AL User’s Guide
1. Observe the safety and ESD precautions in “Safety Information” .
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord(s) from the server.
4. Remove the server's cover and locate the battery. See the documentation that came with your server chassis for instructions on removing the server's cover.
5. Insert the tip of a small flat bladed screwdriver, or an equivalent, under the tab in the plastic retainer. Gently push down on the screwdriver to lift the battery.
6. Remove the battery from its socket.
Figure 73. Replacing the Backup Battery
TP02079
7. Dispose of the battery according to local ordinance.
8. Remove the new lithium battery from its package, and, being careful to observe the correct polarity, insert it in the battery socket.
9. Close the chassis.
10. Run Setup to restore the configuration settings to the RTC.
Intel® Server System SR2500AL User’s Guide 85
Replacing the Power Supply
Caution: The power supply is only hot-swappable if you have a redundant system with two power supplies installed. If you only have one power supply installed, before removing or replacing the power supply, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet.
The power supply can be replaced if it fails or if one of the fans that is integrated into it fails. To replace the power supply, use the following instructions.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. If a filler panel is installed, press the release lever (see letter “A”) and use the finger hole (see letter “B”) to remove the filler panel as shown in the figure below.
B
A
AF000021
Figure 74. Removing Power Supply Filler Panel from the Server System
5. If a power supply is installed, release the latch (see letter “A”) and remove the power supply by pulling on the handle (see letter “B”) as shown in the figure below.
86 Intel® Server System SR2500AL User’s Guide
B A
AF000022
Figure 75. Removing Power Supply Module from the Server System
6. Insert the replacement power supply module into the power supply cage until it clicks into place.
AF000024
Figure 76. Installing Power Supply Module into the Server System
7. If no power supply is to be installed, insert a power supply filler panel as shown in the figure below.
AF000023
Figure 77. Installing Power Supply Filler Panel into the Server System
8. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
9. Plug all peripheral devices and the AC power cable(s) into the server.
Intel® Server System SR2500AL User’s Guide 87
Replacing the Power Distribution Module
To replace the power distribution module, use the following instructions.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
5. Remove the fan module assembly. For instructions, see “Replacing a Fan Module” .
6. Disconnect all power cables from the server board, backplane, and mid-plane.
7. Remove the hot-swap power supply/supplies. For instructions, see “Replacing the
Power Supply” .
8. Remove the two screws to release the module (see letter “A”).
9. Lift the module from the server system (see letter “B”).
A
B
A
88
AF000146
Figure 78. Removing the Power Distribution Module
10. Set the replacement power supply distribution module into the server system and screw the module into place.
11. Install the hot-swap power supply/supplies. For instructions, see “Replacing the
Power Supply” .
Intel® Server System SR2500AL User’s Guide
12. Connect all power cables to the server board.
13. Install the fan module assembly. For instructions, see “Replacing a Fan Module” .
14. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
15. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
16. Plug all peripheral devices and the AC power cable(s) into the server.
Replacing the Control Panel
The steps for replacing the standard control panel and the Intel ® necessary, differences between the two control panels are noted.
Local Control Panel are nearly identical. Use the steps below for both varieties of the control panel. Where
Your server must be operated with a control panel installed.
Caution: The control panel is NOT hot swappable. Before removing or replacing the control panel, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
4. Remove the server system cover. For instructions, see “Removing the System
Cover” .
Intel® Server System SR2500AL User’s Guide 89
5. Press the latch at the back of the control panel (see letter “A” in the figure below).
6. Slide the control panel out through the front of the server system (see letter “B” in the figure below).
A
B
AF000005
Figure 79. Removing Standard Control Panel Module from the Server
System
7. Slide the replacement control panel into the server system (see letter “A”) until it clicks into place (see letter “B”).
B
90
A
AF000006
Figure 80. Installing Control Panel Module into the Server System
Intel® Server System SR2500AL User’s Guide
8. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
9. (Optional) Install the front bezel. For instructions, see “Installing the Front Bezel” .
10. Plug all peripheral devices and the AC power cable(s) into the server.
Replacing a Fan Module
Replacing a Redundant Fan Module
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
6. Remove the optical drive cable if installed.
7. Remove the bridge board. For instructions, see Figure 61 “Removing the Bridge
Board from the Server System” on page -71 .
8. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
9. Disconnect the fan cables from the mid-plane.
Intel® Server System SR2500AL User’s Guide 91
10. Remove the fan module assembly by releasing the blue retention mechanism (see letter “A” in the figure below), sliding the assembly to the left (see letter “B”), and lifting the assembly off of the standoff and out of the system (see letter “C”).
A
B
C
B
C
Figure 81. Removing the Redundant Fan Module
11. Install the replacement fan module assembly by lowering it over the standoff (see letter “A” in the figure below), and sliding the assembly to the right (see letter “B”).
B
A
B
A
92
Figure 82. Installing the Redundant Fan Module
12. Connect the fan cables to the mid-plane.
13. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
Re-route cables through the air baffle as necessary.
Intel® Server System SR2500AL User’s Guide
14. Install the bridge board. For instructions, see Figure 64 “Installing the Bridge
Board into the Server System” on page -73 .
15. Install the optical drive cable (optional).
16. Install the PCI riser assembly. For instructions, see “Installing the PCI Riser
Assembly” .
17. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
18. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
19. Plug all peripheral devices and the AC power cable(s) into the server.
Replacing a Fixed Fan Module
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the processor air duct. For instructions, see “Removing the Processor Air
Duct” .
5. Remove the PCI riser assembly. For instructions, see “Removing the PCI Riser
Assembly” .
6. Remove the optical drive cable if installed.
7. Remove the bridge board. For instructions, see Figure 61 “Removing the Bridge
Board from the Server System” on page -71 .
8. Remove the large air baffle. For instructions, see “Removing the Large Air Baffle” .
9. Disconnect the fan cables from the mid-plane.
Intel® Server System SR2500AL User’s Guide 93
94
10. Remove the fan module assembly by pulling the blue retention mechanism towards the middle fan (see letter “A” in the figure below) and sliding the assembly to the left (see letter “B” in), and lifting the assembly off of the standoff and out of the system (see letter “C”).
A
B
C
B
C
Figure 83. Removing the Fixed Fan Module
11. Install the replacement fan module assembly by lowering it over the standoff (see letter “A” in the figure below), and sliding the assembly to the right (see letter “B”).
B
A
B
A
Figure 84. Installing the Fixed Fan Module
Intel® Server System SR2500AL User’s Guide
12. Connect the fan cables to the mid-plane.
13. Install the large air baffle. For instructions, see “Installing the Large Air Baffle” .
14. Install the bridge board. For instructions, see Figure 64 “Installing the Bridge
Board into the Server System” on page -73 .
15. Install the optical drive cable (optional).
16. Install the PCI riser assembly. For instructions, see “Installing the PCI Riser
Assembly” .
17. Install the processor air duct. For instructions, see “Installing the Processor Air
Duct” .
18. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
19. Plug all peripheral devices and the AC power cable(s) into the server.
Replacing a Redundant System Fan
Note: The fans that are integrated into the power supply cannot be replaced separately. If one of the fans in the power supply fails, the power supply must be replaced.
The system fans at the front of the server system can be individually replaced if one of them fails. Use the steps below to replace a system fan.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Remove the server system cover. For instructions, see “Removing the System
Cover” .
3. There are no screws to loosen. Lift the failed fan from the module.
Intel® Server System SR2500AL User’s Guide 95
96
6
5
3
4
1
2
AF000004
Figure 85. Removing a Fan from the Redundant Fan Module
4. Position the replacement fan so the connector on the fan is at the right and pointing down.
Note: Fan locations 1, 2, 3, and 4 use 80mm fans. Fan locations 5 and 6 use 60mm fans.
5. With the fan oriented correctly, insert the fan into the fan module, engaging the connector on the fan into the matching connector on the fan module.
6
5
3
4
1
2
AF000009
Figure 86. Installing a Fan into the Redundant Fan Module
Intel® Server System SR2500AL User’s Guide
6. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
Replacing a Fixed Fan
Caution: The system fans are NOT hot swappable. Before removing or replacing a fan, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet.
Note: The fans that are integrated into the power supply cannot be replaced separately. If one of the fans in the power supply fails, the power supply must be replaced.
The system fans at the front of the server system can be individually replaced if one of them fails. Use the steps below to replace a fan.
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Remove the fan module assembly. For instructions, see “Replacing a Fan Module” .
5. There are no screws to loosen. Remove the fan from the fan module (see letter “A” in the figure below).
3
2
1
A
Figure 87. Removing a Fan from the Fixed Fan Module
6. Position the replacement fan so the connector on the fan is at the right and pointing down.
7. With the fan oriented correctly, insert the fan into the fan module (see letter “A” in the figure below), and snap in place.
Intel® Server System SR2500AL User’s Guide 97
3
2
1
A
Figure 88. Installing a Fan into the Fixed Fan Module
8. Install the fan module assembly. For instructions, see “Replacing a Fan Module” .
9. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
10. Plug all peripheral devices and the AC power cable(s) into the server.
Installing and Removing the Rack Handles
Installing the Rack Handles
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the server system cover. For instructions, see “Removing the System
Cover” .
4. Align the rack handle with the two holes on the side of the server system as shown in the figure below.
5. Attach the rack handle to the server system with two screws as shown in the figure below.
98 Intel® Server System SR2500AL User’s Guide
AF000019
Figure 89. Installing the Rack Handle
6. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
7. Install the front bezel. For instructions, see “Installing the Front Bezel” .
8. Plug all peripheral devices and the AC power cable(s) into the server.
Removing the Rack Handles
1. Observe the safety and ESD precautions at the beginning of this book. See “Safety
Information” .
2. Power down the server and unplug all peripheral devices and the AC power cable(s).
3. Remove the front bezel if it is installed. For instructions, see “Removing the Front
Bezel” .
4. Remove the server system cover. For instructions, see “Removing the System
Cover” .
5. Remove the two screws holding the rack handle in place, and remove the rack handle from the server system as shown in the figure below.
Intel® Server System SR2500AL User’s Guide 99
AF000020
Figure 90. Removing the Rack Handle
6. Install the server system cover. For instructions, see “Installing the Server System
Cover” .
7. Plug all peripheral devices and the AC power cable(s) into the server.
100 Intel® Server System SR2500AL User’s Guide
4
Server Utilities
Using the BIOS Setup Utility
This section describes the BIOS Setup Utility options, which is used to change server configuration defaults. You can run BIOS Setup with or without an operating system being present. See setup screens.
“Server System References” for a link to the Intel ® 5000 Series
Chipsets Server Board Family Datasheet where you will find details about specific BIOS
Starting Setup
You can enter and start BIOS Setup under several conditions:
• When you turn on the server, after POST completes the memory test.
• When you have moved the CMOS jumper on the server board to the "Clear CMOS" position (enabled).
In the two conditions listed above, during the Power On Self Test (POST), you will see this prompt:
Press <F2> to enter SETUP
In a third condition, when CMOS/NVRAM has been corrupted, you will see other prompts but not the <F2> prompt:
Warning: CMOS checksum invalid
Warning: CMOS time and date not set
In this condition, the BIOS will load default values for CMOS and attempt to boot.
If You Cannot Access Setup
If you are not able to access BIOS Setup, you might need to clear the CMOS memory. For instructions on clearing the CMOS, see " Clearing the CMOS ".
Setup Menus
Each BIOS Setup menu page contains a number of features. Except for those features that are provided only to display automatically configured information, each feature is associated with a value field that contains user-selectable parameters. These parameters can be changed if the user has adequate security rights. If a value cannot be changed for any reason, the feature's value field is inaccessible.
102
“Setup Menu Key Use” describes the keyboard commands you can use in the BIOS Setup menus.
Table 4. Setup Menu Key Use
Key to Press Description
<F1> Pressing <F1> on any menu invokes the general help window.
Left and right arrows The left and right arrow keys are used to move between the major menu pages. The keys have no affect if a submenu or pick list is displayed.
Up arrow
Down arrow
Select Item up - The up arrow is used to select the previous value in a menu item's option list, or a value field pick list. Pressing the <Enter> key activates the selected item.
Select Item down - The down arrow is used to select the next value in a menu item's option list, or a value field pick list. Pressing the <Enter> key activates the selected item.
<F5> or <->
<F6> or <+>
<Enter>
<Esc>
<F9>
Change Value - The minus key or the <F5> function key is used to change the value of the current item to the previous value. This key scrolls through the values in the associated pick list without displaying the full list.
Change Value - The plus key or the <F6> function key is used to change the value of the current menu item to the next value. This key scrolls through the values in the associated pick list without displaying the full list. On 106-key Japanese keyboards, the plus key has a different scan code than the plus key on the other keyboard, but it has the same effect.
Execute Command - The <Enter> key is used to activate submenus when the selected feature is a submenu, or to display a pick list if a selected feature has a value field, or to select a sub-field for multi-valued features like time and date. If a pick list is displayed, the <Enter> key will undo the pick list, and allow another selection in the parent menu.
Exit - The <Esc> key provides a mechanism for backing out of any field.
This key will undo the pressing of the <Enter> key. When the <Esc> key is pressed while editing any field or selecting features of a menu, the parent menu is re-entered. When the <Esc> key is pressed in any submenu, the parent menu is re-entered. When the <Esc> key is pressed in any major menu, the exit confirmation window is displayed and the user is asked whether changes can be discarded.
Setup Defaults - Pressing <F9> causes the following to appear:
Setup Confirmation
Load default configuration now?
[Yes] [No]
If "Yes" is selected and the <Enter> key is pressed, all Setup fields are set to their default values. If "No" is selected and the <Enter> key is pressed, or if the <Esc> key is pressed, the user is returned to where they were before <F9> was pressed without affecting any existing field values.
Intel® Server System SR2500AL User’s Guide
Key to Press
<F10>
Table 4. Setup Menu Key Use
Description
Save and Exit - Pressing <F10> causes the following message to appear:
Setup Confirmation
Save Configuration changes and exit now?
[Yes] [No]
If "Yes" is selected and the <Enter> key is pressed, all changes are saved and Setup is exited. If "No" is selected and the <Enter> key is pressed, or the <Esc> key is pressed, the user is returned to where they were before <F10> was pressed without affecting any existing values.
Upgrading the BIOS
The upgrade utility allows you to upgrade the BIOS in flash memory. The code and data in the upgrade file include the following:
• On-board system BIOS, including the recovery code, BIOS Setup Utility, and strings.
• On-board video BIOS, and other option ROMs for devices embedded on the server board.
• OEM binary area
• Microcode
• A way to change the BIOS language
Preparing for the Upgrade
The steps below explain how to prepare to upgrade the BIOS, including how to record the current BIOS settings and how to obtain the upgrade utility.
Note: In the unlikely event that a BIOS error occurs during the BIOS update process, a recovery process may need to be followed to return the system to service. See “Server System
References” for a link to necessary software and instrutions.
Recording the Current BIOS Settings
1. Boot the computer and press <F2> when you see the message:
Press <F2> Key if you want to run SETUP
2. Write down the current settings in the BIOS Setup program.
Note: Do not skip step 2. You will need these settings to configure your server at the end of the procedure.
Intel® Server System SR2500AL User’s Guide 103
Obtaining the Upgrade
Download the BIOS image file to a temporary folder on your hard drive. See “Server
System References” for a link to the update software.
Note: Review the instructions and release notes that are provided in the readme file distributed with the BIOS image file before attempting a BIOS upgrade. The release notes contain critical information regarding jumper settings, specific fixes, or other information to complete the upgrade.
Upgrading the BIOS
Follow the instructions in the readme file that came with the BIOS upgrade. When the update completes, remove the bootable media from which you performed the upgrade.
Caution: Do not power down the system during the BIOS update process! The system will reset automatically when the BIOS update process is completed.
Note: You may encounter a CMOS Checksum error or other problem after reboot. If this happens, shut down the system and boot it again. CMOS checksum errors require that you enter Setup, check your settings, save your settings, and exit Setup.
Clearing the Password
If the user or administrator password(s) is lost or forgotten, moving the password clear jumper into the "clear" position clears both passwords. The password clear jumper must be restored to its original position before a new password(s) can be set.
1. Power down the system and disconnect the AC power.
2. Open the server chassis.
3. Move the jumper from the normal operation position, Password Clear Protect, at pins 1 and 2 to the Password Clear Erase position, covering pins 2 and 3.
104 Intel® Server System SR2500AL User’s Guide
BMC Force
Update Mode
2
3
J1D2
Password
Reset
2
3
J1D1
Disable
Enable
2
3
J1D3
Clear
CMOS
TP02080
Figure 91. Clear Password Jumper
4. Wait five seconds.
5. Return the Password Clear jumper to the Password Clear Protect position, covering pins 1 and 2.
6. Close the server chassis.
7. Reconnect the AC power and power up the server.
8. The password is now cleared and can be reset by going into BIOS setup.
Clearing the CMOS
If you are not able to access the BIOS setup screens, the CMOS Clear jumper will need to be used to reset the configuration RAM.
1. Power down the system and disconnect the AC power.
2. Open the server.
3. Move the jumper from the normal operation position, CMOS Clear by BMC, at pins 1 and 2 to the CMOS Clear Force Erase position, covering pins 2 and 3.
Intel® Server System SR2500AL User’s Guide 105
2
3
J1D2
Password
Reset
BMC Force
Update Mode
2
3
J1D1
Disable
Enable
2
3
J1D3
Clear
CMOS
TP02080
Figure 92. Clear CMOS Jumper
4. Wait five seconds.
5. Return the CMOS Clear jumper to the CMOS Clear by BMC location, covering pins 1 and 2.
6. Close the server chassis.
7. Reconnect the AC power and power up the system.
8. The CMOS is now cleared and can be reset by going into the BIOS setup.
106 Intel® Server System SR2500AL User’s Guide
Appendix A: Technical Reference
Cable Routing
When you add or remove components from your server system, make sure your cables are routed correctly before reinstalling the server system cover. Use caution to make sure no cables or wires are pinched and that the airflow from the fans is not blocked. Use the figures below to determine the correct cable routing.
D
A
C
B
E
F
A Power to Server Board (Aux.)
B Power to Server Board (Main)
C Power to Server Board (CPU)
D Power to Midplane Board
E Power to Backplane Board
F RAID Battery to Active Midplane Board
Figure 93. Cable Routing
AF000328
Fan Connections
Use the figures below to determine the proper fan connections.
3
2
1
AF000145
Figure 94. Connecting the Non-redundant Fan Power Cables to the Passive
Mid-plane Board
5
6
3
4
1
2
108
TP02140
Figure 95. Connecting the Redundant Fan Power Cables to the Active Midplane Board
Intel® Server System SR2500AL User’s Guide
750W Single Power Supply Input Voltages
• 100-127V at 50/60 Hz; 12 A max.
• 200-240V at 50/60 Hz; 6 A max.
750W Single Power Supply Output Voltages
The table below lists the total wattage available from the power subsystem for each voltage. Ensure that your loads do not exceed the combined total wattage of 750 Watts.
For information about calculating the power usage for your configuration, see
"Calculating Power Usage."
Table 5. Power Supply Output Capability
Voltage
+3.3 V
+5.0 V
+5 V Standby
36 A
45 A
Maximum Current
-12.0 V 2.0 A
Warning: Do not exceed a combined power output of 90 Watts for the +5 V and +3.3 V outputs.
Exceeding a combined 90 Watts will overload the power subsystem and may cause the power supplies to overheat and malfunction.
Intel® Server System SR2500AL User’s Guide 109
System Environmental Specifications
Temperature
Non-operating
Operating
Table 6. System Environmental Specifications
-40 ° to 70 °C.
10 ° to 35 °C; derated 0.5 °C for every 1000 ft (305 m) to a maximum of
10,000 ft.
Humidity
Non-operating
Shock
Operating
Packaged
Acoustic noise
Electrostatic discharge (ESD)
90% relative humidity (non-condensing) at 30 °C.
2.0 g, 11 msec, 1/2 sine
Operational after an 18" free fall.
7 Bels in sound power for a typical office ambient temperature
(65-75 °F). Your selection of peripherals may change the noise level.
Tested to 15 kilovolts (kV); no component damage.
110 Intel® Server System SR2500AL User’s Guide
Appendix B: Troubleshooting
This chapter helps you identify and solve problems that might occur while you are using the system.
For any issue, first ensure you are using the latest firmware and files. Firmware upgrades include updates for BIOS, the Baseboard Management Controller (BMC), and the hotswap controller (HSC). See “Server System References” for a link to the software updates. In addition to the server firmware and files, also update any drivers used for components you have installed in your system, such as video drivers, network drivers, and
SATA drivers.
Intel provides a package called the "Platform Confidence Test" that may help with your diagnostics. See “Server System References” for a link to this software.
If you are unable to resolve your server problems on your own, see “Getting Help” for assistance.
Resetting the System
Before going through in-depth troubleshooting, attempt first to reset your system using one of the methods below.
Table 7. Resetting the System
To do this
Soft boot reset to clear the system memory and reload the operating system
Clear system memory, restart POST, and reload the operating system
Cold boot reset. Turn the system power off and then on. This clears system memory, restarts POST, reloads the operating system, and halts power to all peripherals
Reset the BMC and get it back to a stable state
Press
<Ctrl+Alt+Del>
Reset button
Power off/on button
Remove AC power from the server for one minute
Problems following Initial System Installation
Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less frequent cause. If the problem you are experiencing is with a specific software application, see “Problems with Newly Installed
Application Software” .
First Steps Checklist
• Is AC power available at the wall outlet?
• Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis and at the AC source.
• Are all cables correctly connected and secured?
• Are the processors fully seated in their sockets on the server board?
• Are all standoffs in the proper location and not touching any components, causing a potential short?
• Are all add-in PCI boards fully seated in their slots on the server board?
• Are all jumper settings on the server board correct?
• Are all jumper and switch settings on add-in boards and peripheral devices correct?
To check these settings, refer to the manufacturer's documentation that comes with them. If applicable, ensure that there are no conflicts-for example, two add-in boards sharing the same interrupt.
• Are all peripheral devices installed correctly?
• If the system has a hard disk drive, is it properly formatted or configured?
• Are all device drivers properly installed?
• Are the configuration settings made in Setup correct?
• Is the operating system properly loaded? See the operating system documentation.
• Did you press the system power on/off switch on the front panel to turn the server on
(power on light should be lit)?
• Is the system power cord properly connected to the system and plugged into a
NEMA 5 15R outlet for 100-120V or a NEMA 6-15R outlet for 200-240V ?
• Are all integrated components from the tested components lists? Check the tested memory, and chassis lists, as well as the supported hardware and operating system list. See “Server System References” for links to the tested component lists.
Hardware Diagnostic Testing
This section provides a more detailed approach to identifying a hardware problem and locating its source.
112 Intel® Server System SR2500AL User’s Guide
Caution: Turn off devices before disconnecting cables: Before disconnecting any peripheral cables from the system, turn off the system and any external peripheral devices. Failure to do so can cause permanent damage to the system and/or the peripheral devices.
1. Turn off the system and all external peripheral devices. Disconnect each device from the system, except for the keyboard and the video monitor.
2. Make sure the system power cord is plugged into a properly grounded AC outlet.
3. Make sure your video display monitor and keyboard are correctly connected to the system. Turn on the video monitor. Set its brightness and contrast controls to at least two thirds of their maximum ranges (see the documentation supplied with your video display monitor).
4. If the operating system normally loads from the hard disk drive, make sure there is no CD-ROM / DVD disk in the optical drive.
5. If the power LED does light, attempt to boot from a USB floppy or from a CD-
ROM disk.
6. Turn on the system. If the power LED does not light, see “Power Light Does Not
Light” .
Verifying Proper Operation of Key System Lights
As POST determines the system configuration, it tests for the presence of each mass storage device installed in the system. As each device is checked, its activity light should turn on briefly. Check for the following:
• Does the drive activity light turn on briefly? If not, see “Drive Activity Light Does
Not Light” .
• If system LEDs are illuminated, see “Make sure the BIOS is configured to allow the
CD-ROM to be the first bootable device.” for a description of the light and steps to take to correct the problem.
Confirming Loading of the Operating System
Once the system boots up, the operating system prompt appears on the screen. The prompt varies according to the operating system. If the operating system prompt does not appear, see “No Characters Appear on Screen” .
Specific Problems and Corrective Actions
This section provides possible solutions for these specific problems:
• Power light does not light.
• No characters appear on screen.
• Characters on the screen appear distorted or incorrect.
Intel® Server System SR2500AL User’s Guide 113
• System cooling fans do not rotate.
• Diskette drive activity light does not light.
• Hard disk drive activity light does not light.
• CD-ROM drive activity light does not light.
• There are problems with application software.
• The bootable CD-ROM is not detected.
Try the solutions below in the order given. If you cannot correct the problem, contact your service representative or authorized dealer for help.
Power Light Does Not Light
Check the following:
• Did you press the power-on button?
• Is the system operating normally? If so, the power LED might be defective or the connection from the control panel to the server board might be loose.
• Have you securely plugged the server AC power cord into the power supply?
• Some ATX power supplies have a power switch on the back of the power supply, next to the fan. If your system has one, is it turned on?
• Remove all add-in cards and see if the system boots. If successful, add the cards back in one at a time with a reboot between each addition.
• Make sure the memory DIMMs comply with the system requirements.
• Make sure the memory DIMMs have been populated according to the system requirements.
• Remove the memory DIMMs and re-seat them.
• Make sure the processor(s) comply with the system requirements.
• Make sure the processor(s) have been populated according to the system requirements.
• Remove the processor(s) and re-seat them.
• Make sure the chassis standoffs are installed only below mounting holes. Misplaced standoffs can contact the pins on the bottom of the server board and cause a short.
No Characters Appear on Screen
Check the following:
• Is the keyboard functioning? Test it by turning the "Num Lock" function on and off to make sure the Num Lock light is functioning.
• Is the video monitor plugged in and turned on? If you are using a switch box, is it switched to the correct system?
114 Intel® Server System SR2500AL User’s Guide
• Are the brightness and contrast controls on the video monitor properly adjusted?
• Is the video monitor signal cable properly installed?
• Does this video monitor work correctly if plugged into a different system?
• Is the onboard video controller enabled in the BIOS?
• Remove all add-in cards and see if the video returns. If successful, add the cards back in one at a time with a reboot between each addition.
• Make sure the memory DIMMs comply with the system requirements.
• Make sure the memory DIMMs have been populated according to the system requirements.
• Remove the memory DIMMs and re-seat them.
• Make sure the processor(s) comply with the system requirements.
• Make sure the processor(s) have been populated according to the system requirements.
• Remove the processor(s) and re-seat them.
If you are using an add-in video controller board, do the following:
1. Verify that the video works using the onboard video controller.
2. Verify that the video controller board is fully seated in the server board connector.
3. Reboot the system for changes to take effect.
4. If there are still no characters on the screen after you reboot the system and POST emits a beep code, write down the beep code you hear. This information is useful for your service representative.
5. If you do not receive a beep code and characters do not appear, the video display monitor or video controller may have failed. Contact your service representative or authorized dealer for help.
Characters Are Distorted or Incorrect
Check the following:
• Are the brightness and contrast controls properly adjusted on the video monitor? See the manufacturer's documentation.
• Are the video monitor's signal and power cables properly installed?
• Does this video monitor work correctly if plugged into a different system?
System Cooling Fans Do Not Rotate Properly
If the system cooling fans are not operating properly, it is an indication of possible system component failure.
Check the following:
Intel® Server System SR2500AL User’s Guide 115
• Is the power-on light lit? If not, see “Power Light Does Not Light” .
• If your system has LED lights for the fans, is one or more of these LEDs lit?
• Are any other control panel LEDs lit?
• Have any of the fan motors stopped? Use the server management subsystem to check the fan status.
• Have your fans speeded up in response to an overheating situation?
• Have your fans speeded up in response to a fan that has failed?
• Are the fan power connectors properly connected to the server board?
• Is the cable from the control panel board connected to the both the control panel board and to the server board?
• Are the power supply cables properly connected to the server board?
• Are there any shorted wires caused by pinched-cables or have power connector plugs been forced into power connector sockets the wrong way?
Drive Activity Light Does Not Light
Check the following:
• Are the drive's power and signal cables properly installed?
• Are all relevant switches and jumpers on the drive set correctly?
• Is the drive properly configured?
• Is the drive activity light always on? If so, the signal cable may be plugged in incorrectly.
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not
Light
Check the following:
• Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed?
• Are all relevant switches and jumpers on the drive set correctly?
• Is the drive properly configured?
Cannot Connect to a Server
• Make sure the network cable is securely attached to the correct connector at the system back panel.
• Try a different network cable.
• Make sure you are using the correct and the current drivers. See “Server System
References” for a link to the current drivers.
116 Intel® Server System SR2500AL User’s Guide
• Make sure the driver is loaded and the protocols are bound.
• Make sure the hub port is configured for the same duplex mode as the network controller.
• Make sure the correct networking software is installed.
• If you are directly connecting two servers (without a hub), you will need a crossover cable.
• Check the network controller LEDs next to the NIC connectors.
Problems with Network
The server hangs when the drivers are loaded
• Certain drivers may require interrupts that are not shared with other PCI drivers. For these drivers, it may be necessary to alter settings so that interrupts are not shared.
See the documentation that came with your PCI card(s) for information on changing interrupts.
Diagnostics pass but the connection fails
• Make sure the network cable is securely attached.
• Make sure you specify the correct frame type in your NET.CFG file.
• The controller stopped working when an add-in adapter was installed.
• Make sure the cable is connected to the port from the onboard network controller.
• Make sure your BIOS is current. See “Server System References” for a link to the current version.
• Make sure the other adapter supports shared interrupts. Make sure your operating system supports shared interrupts.
• Try reseating the add-in adapter.
The add-in adapter stopped working without apparent cause
• Reseat the adater.
• Put the adapter in a different slot.
• The network driver files may be corrupt or deleted. Delete and then reinstall the drivers.
• Run diagnostics.
Intel® Server System SR2500AL User’s Guide 117
System Boots when Installing PCI Card
System Management features require full-time "standby" power. This means some parts of the system have power going to them whenever the power cord is plugged in, even if you have turned the system power off with the power button on the front panel. If you install a PCI card with the AC power cord plugged in, a signal may be sent to command the system to boot. Before installing a PCI card, you should always:
• Turn off the server power by using the power button on the front of the system.
• Unplug the AC power cord(s) from the server.
Problems with Newly Installed Application Software
Problems that occur when you run new application software are usually related to the software, not the server hardware. Faulty equipment is unlikely, especially if other software runs correctly.
Check the following:
• Make sure the system meets the minimum hardware requirements for the software.
See the software documentation.
• Make sure the software is properly installed and configured for the system. See the software documentation.
• Use only an authorized copy. Unauthorized copies often do not work.
• If you are running the software from a CD-ROM or DVD-ROM, try a different disk.
• Make sure the correct device drivers installed.
If the problems persist, contact the software vendor's customer service representative.
Problems with Application Software that Ran Correctly
Earlier
Problems that occur after the system hardware and software have been running correctly sometimes indicate equipment failure. However, they can also be caused by file corruption or changes to the software configuration.
Check the following:
• If you are running the software from a CD-ROM or DVD-ROM, try a different disk.
• Check your system for a virus infection.
• Uninstall and reinstall the software. Make sure all necessary files are installed.
• If the problems are intermittent, there may be a loose cable, dirt in the keyboard (if keyboard input is incorrect), a marginal power supply, or other random component failures.
• If you suspect that a transient voltage spike, power outage, or brownout might have occurred, reload the software and try running it again. Symptoms of voltage spikes
118 Intel® Server System SR2500AL User’s Guide
include a flickering video display, unexpected system reboots, and the system not responding to user commands.
Note: Random errors in data files: If you are getting random errors in your data files, they may be getting corrupted by voltage spikes on your power line. If you are experiencing any of the above symptoms that might indicate voltage spikes on the power line, you may want to install a surge suppressor between the power outlet and the system power cord.
Devices are not Recognized under Device Manager
(Microsoft* Windows* Operating System)
The Microsoft* Windows* operating systems do not include all of the drivers for the
Intel ® chipsets, onboard NICs, and other components. See “Server System References” for a link to the current drivers and chipset files.
Hard Drive(s) are not Recognized
Check the following:
• Make sure the drive is not disabled in BIOS Setup.
• Make sure the drive is connected correctly and that is plugged into the power supply.
• Make sure the drive is compatible. See “Server System References” for a link to the tested drives.
• Make sure you have not exceeded the power budget for the server. See “Server
System References” for a link to software to check your power budget.
• If using SCSI drives, verify that each SCSI ID number is unique on the SCSI bus.
See your drive documentation for details on setting the SCSI ID for your drives.
• If using ATA drives, verify that the master/slave settings are set correctly. See your drive documentation for details on setting the master/slave settings.
• If using a RAID configuration with SCSI or SATA drives, make sure the RAID card is installed correctly.
Bootable CD-ROM Disk Is Not Detected
Check the following:
• Make sure the BIOS is configured to allow the CD-ROM to be the first bootable device.
Intel® Server System SR2500AL User’s Guide 119
LED Information
The Intel
®
Server Board S5000PAL includes LEDs that can aid in troubleshooting your system. A table of these LEDs with a description of their use is listed below.
Table 8. LED Information
LED Name
Power
ID
System
Status
Function
Indicates system power is on or off
Location
Front control panel
Aid in server identification from the back panel
Visible fault warning
LED Color
Green
Front control panel and board rear left corner
Control panel and board rear left corner
Blue
Green or
Amber
Notes
Off = Power is off or in sleep state S5
On = Power is on or in sleep stats S0
Press ID LED button or use
Server Management software to turn the LED on and off.
Green = No Fault
Green blinking = degraded condition
Amber blinking = non-critical error
Amber = critical or nonrecoverable error
BIOS POST Beep Codes
The table below lists the POST error beep codes. Prior to system video initialization, the
BIOS uses these beep codes to inform users of error conditions. Please note that not all error conditions are supported by BIOS beep codes.
Table 9. POST Error Beep Codes
Number of
Beeps
1, 2, or 3
Reason for Beeps and Action to Take
4 - 7 or 9 - 11
8
Memory error. Reseat the memory or replace the DIMMs with known good modules.
Fatal error indicating a possible serious system problem. Remove all add-in cards and re-start the system. If the error still occurs, contact your system manufacturer. If the beep codes are not generated after the add-in cards are removed, insert the cards one at a time, booting the system between each card addition, until the beeps again occur to reveal the malfunctioning card.
Replace or reseat the system video add-in card. If on-board video is bing used, the server board may be faulty.
120 Intel® Server System SR2500AL User’s Guide
In addition to the beep codes above, additional beep codes are provided if an Intel ®
Remote Management Module is installed. The Intel ® provides the following additional beep codes.
Remote Management Module
Table 10. Error Beep Codes Generated by Intel
®
Remote Management
Module
Number of
Beeps
1
1-5-1-1
1-5-2-1
Reason for Beeps and Action to Take
1-5-2-3
1-5-2-4
1-5-4-2
1-5-4-3
1-5-4-4
Control panel CMOS clear has been initiated.
Processor failure. Reseat or replace the failed processor.
No processor is installed or the CPU 1 socket is empty. Reseat or replace the failed processor.
Processor configuration error or CPU 1 socket is empty. Reseat or replace the failed processor. In a two-processor system, make sure the processors are identical.
Front-side bus select configuration error.
DC power unexpectedly lost.
Chipset control failure.
Power control failure.
Intel® Server System SR2500AL User’s Guide 121
122 Intel® Server System SR2500AL User’s Guide
Appendix C: Intel
®
Server Issue Report
Form
Note: An on-line / automatic submission version of this form is available at http:// support.intel.com/support/motherboards/server/chassis/SR2500/. For the fastest service, please submit your form via the Internet.
Date Submitted: _______________________________________________________
Company Name: ______________________________________________________
Contact Name: ________________________________________________________
Email Address: _______________________________________________________
Intel Server Product: ___________________________________________________
Priority (Critical, Hot, High, Low): _______________________________________
Brief Problem Description. Provide a brief description below. See the last page for space to include a detailed problem description.
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
Board / Chassis Information
Baseboard Revision - PBA#: _____________________________________________
Baseboard Serial Number: _______________________________________________
Chassis Model:________________________________________________________
CPU1 Speed/Stepping/Spec: _____________________________________________
CPU2 Speed/Stepping/Spec: _____________________________________________
System BIOS Version: __________________________________________________
HSC Firmware Version: _________________________________________________
DIMM Configuration
DIMM A1 MB and Vendor / part number: __________________________________
DIMM A2 MB and Vendor / part number: __________________________________
DIMM B1 MB and Vendor / part number: __________________________________
DIMM B2 MB and Vendor / part number: __________________________________
DIMM C1 MB and Vendor / part number: __________________________________
DIMM C2 MB and Vendor / part number: __________________________________
DIMM D1 MB and Vendor / part number: __________________________________
DIMM D2 MB and Vendor / part number: __________________________________
Operating System Information
Operating System:_____________________________________________________
Version: _____________________________________________________________
Service Pack:_________________________________________________________
Add-in Card, Peripheral, Video, NIC
Check each box below as applicable, and provide the requested information.
Peripheral Card or Peripheral Description Driver Revision IRQ # I/O Base Address NIC
Description
Driver
Revision
IRQ
I/O Base
Address
FW
Revision
Peripheral
PCI-X*
Top PCI Slot
Middle PCI Slot
Bottom PCI Slot
PCIe* x4
Top PCI Slot
Middle PCI Slot
Bottom PCI Slot
PCIe x8
Top PCI Slot
Middle PCI Slot
Bottom PCI Slot
124 Intel® Server System SR2500AL User’s Guide
Peripheral
Video
On-board Video
Add-in Video
NIC
On-Board NIC1
On-Board NIC2
Description
Hard Drive Information
Drive Type (SCSI,
SATA, etc)
Make/Model
Driver
Revision
IRQ
I/O Base
Address
FW
Revision
Hot-swap or Fixed
IRQ
FW
Revision
Management Information
On-Board Platform Instrumentation only ___________________________________
Intel ® Remote Management Module _______________________________________
Control Panel Information
Standard Control Panel _________________________________________________
Intel ® Local Control Panel_______________________________________________
Intel® Server System SR2500AL User’s Guide 125
Complete Problem Description
In the space below, provide a complete description of the steps used to reproduce the problem or a complete description of where the problem can be found. Please also include any details on troubleshooting already done.
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
126 Intel® Server System SR2500AL User’s Guide
Appendix D: LED Decoder
During the system boot process, BIOS executes a number of platform configuration processes, each of which is assigned a specific hex POST code number. As each configuration routine is started, BIOS will display the given POST code to the POST
Code Diagnostic LEDs found on the back edge of the server board. To assist in troubleshooting a system hang during the POST process, the Diagnostic LEDs can be used to identify the last POST process to be executed.
Each POST code will be represented by a combination of colors from the four LEDs. The
LEDs are capable of displaying three colors: green, red, and amber. The POST codes are divided into two nibbles, an upper nibble and a lower nibble. Each bit in the upper nibble is represented by a red LED and each bit in the lower nibble is represented by a green
LED. If both bits are set in the upper and lower nibbles then both red and green LEDs are lit, resulting in an amber color. If both bits are clear, then the LED is off.
In the below example, BIOS sends a value of ACh to the diagnostic LED decoder. The
LEDs are decoded as follows:
• red bits = 1010b = Ah
• green bits = 1100b = Ch
Since the red bits correspond to the upper nibble and the green bits correspond to the lower nibble, the two are concatenated to be ACh.
Table 11. POST Progress Code LED Example
8h
LEDs Red
ACh 1
Result Amber
MSB
1
Green Red
0
Green
4h
1
Green Red
1
Red
2h
0
Green Red
0
Off
1h
0
Green
LSB
128
USB Port USB Port
Back edge of server board
Diagnostic LEDs
MSB LSB
Figure 96. Diagnostic LED Placement Diagram
Table 12. Diagnostic LED POST Code Decoder
Diagnostic LED Decoder Description Checkpoint
0x11h
0x12h
0x13h
Chipset
0x21h
Memory
0x22h
G=Green, R=Red, A=Amber
MSB LSB
Host Processor
0x10h OFF OFF OFF R
OFF
OFF
OFF
OFF
OFF
OFF
OFF
G
G
A
R
A
Power-on initialization of the host processor
(bootstrap processor)
Host processor cache initialization (including AP)
Starting application processor initialization
SMM initialization
OFF
OFF
OFF
OFF
R
A
G Initializing a chipset component
0x23h
0x24h
0x25h
0x26h
0x27h
0x28h
OFF
OFF
OFF
OFF
OFF
G
OFF
G
G
G
G
OFF
A
R
R
A
A
R
OFF Reading configuration data from memory (SPD on DIMM)
G Detecting presence of memory
OFF Programming timing parameters in the memory controller
G Configuring memory parameters in the memory controller
OFF Optimizing memory controller settings
G Initializing memory, such as ECC init
OFF Testing memory
Intel® Server System SR2500AL User’s Guide
Table 12. Diagnostic LED POST Code Decoder
PCI Bus
0x50h
0x51h
0x52h
0x53h
0x54h
0x55h
0x56h
0x57h
USB
0x58h
0x59h
G
G
ATA / ATAPI / SATA
0x5Ah
0x5Bh
SMBUS
G
G
0x5Ch
0x5Dh
G
G
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
R
R
R
R
A
A
A
A
R
R
R
R
OFF
OFF
G
G
R
A
A
A
OFF R
OFF A
Local Console
0x70h
0x71h
0x72h
OFF
OFF
OFF
Remote Console
0x78h
0x79h
0x7Ah
G
G
G
R
R
R
R
R
R
R
R
A
R
R
A
Keyboard (PS2 or USB)
0x90h
0x91h
0x92h
R
R
R
OFF OFF R
OFF OFF A
OFF G R
R
A
R
R
A
R
R
A
OFF R
OFF A
G R
G A
OFF R
OFF A
G R
G A
Enumerating PCI busses
Allocating resources to PCI busses
Hot Plug PCI controller initialization
Reserved for PCI bus
Reserved for PCI bus
Reserved for PCI bus
Reserved for PCI bus
Reserved for PCI bus
Resetting USB bus
Reserved for USB devices
Resetting PATA / SATA bus and all devices
Reserved for ATA
Resetting SMBUS
Reserved for SMBUS
Resetting the video controller (VGA)
Disabling the video controller (VGA)
Enabling the video controller (VGA)
Resetting the console controller
Disabling the console controller
Enabling the console controller
Resetting the keyboard
Disabling the keyboard
Detecting the presence of the keyboard
Intel® Server System SR2500AL User’s Guide 129
130
0x93h
0x94h
0x95h
R
R
R
Table 12. Diagnostic LED POST Code Decoder
OFF G
G OFF
A
R
G OFF A
Enabling the keyboard
Clearing keyboard input buffer
Instructing keyboard controller to run Self Test
(PS2 only)
Mouse (PS2 or USB)
0x98h
0x99h
0x9Ah
0x9Bh
A
A
A
A
OFF OFF R
OFF OFF A
OFF G
OFF G
R
A
Fixed Media
0xB0h
0xB1h
0xB2h
R
R
R
OFF R
OFF R
OFF A
R
A
R
OFF A A
Resetting the mouse
Detecting the mouse
Detecting the presence of mouse
Enabling the mouse
Resetting fixed media device
Disabling fixed media device
Detecting presence of a fixed media device (IDE hard drive detection, etc.)
Enabling / configuring a fixed media device 0xB3h R
Removable Media
0xB8h
0xB9h
0xBAh
A
A
A
OFF R
OFF R
OFF A
R
R
A
R
R
Resetting removable media device
Disabling removable media device
Detecting presence of a removable media device
(IDE CDROM detection, etc.)
Enabling / configuring a removable media device 0xBCh A G
Boot Device Selection
0xD0
0xD1
0xD2
0xD3
0xD4
0xD5
0xD6
0xD7
0xD8
0xD9
R
R
R
R
R
R
R
R
A
A
A
A
R
A
R
R
R
A
R
R
OFF R
OFF A
G R
G A
OFF R
OFF A
G R
G A
OFF R
OFF A
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Intel® Server System SR2500AL User’s Guide
Table 12. Diagnostic LED POST Code Decoder
0XDA
0xDB
0xDC
0xDE
0xDF
A
A
A
A
A
R
R
A
A
A
Pre-EFI Initialization (PEI) Core
G
G
OFF R
G R
G
R
A
A
0xE0h
0xE2h
0xE1h
0xE3h
R
R
R
R
R
R
R
R
R
A
R
A
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
Trying boot device selection
G
G
OFF Started dispatching early initialization modules
(PEIM)
OFF Initial memory found, configured, and installed correctly
Reserved for initialization module use (PEIM)
Reserved for initialization module use (PEIM)
Driver Execution Environment (DXE) Core
0xE4h
0xE5h
0xE6h
R
R
R
A
A
A
R
R
A
OFF
G
Entered EFI driver execution phase (DXE)
Started dispatching drivers
OFF Started connecting drivers
DXE Drivers
0xE7h
0xE8h
0xE9h
0xEAh
0xEEh
R
A
A
A
A
A
R
R
R
A
A
R
R
A
A
G Waiting for user input
OFF Checking password
G Entering BIOS setup
OFF Flash Update
OFF Calling Int 19. One beep unless silent boot is enabled.
G Unrecoverable boot failure / S3 resume failure 0xEFh A A A
Runtime Phase / EFI Operating System Boot
0xF4h
0xF5h
0xF8h
0xF9h
R
R
A
A
A
A
R
R
R
R
R
R
R
A
R
A
Entering Sleep state
Exiting Sleep state
Operating system has requested EFI to close boot services (ExitBootServices ( ) has been called)
Operating system has switched to virtual address mode (SetVirtualAddressMap ( ) has been called)
Intel® Server System SR2500AL User’s Guide 131
Table 12. Diagnostic LED POST Code Decoder
0xFAh A R A R Operating system has requested the system to reset (ResetSystem () has been called)
Pre-EFI Initialization Module (PEIM) / Recovery
0x30h
0x31h
0x34h
0x35h
0x3Fh
OFF
OFF
OFF
OFF
G
OFF R
OFF
G
G
G
R
R
R
A
R
A
R
A
A
Crisis recovery has been initiated because of a user request
Crisis recovery has been initiated by software
(corrupt flash)
Loading crisis recovery capsule
Handing off control to the crisis recovery capsule
Unable to complete crisis recovery.
132 Intel® Server System SR2500AL User’s Guide
Appendix E: Getting Help
World Wide Web
http://support.intel.com/support/motherboards/server/chassis/SR2500.
Telephone
All calls are billed per incident, levied in local currency at the applicable credit card exchange rate plus applicable taxes. (Intel reserves the right to change the pricing for telephone support at any time without notice).
Before calling, fill out an “Intel® Server Issue Report Form” . A sample form is provided on the following pages. However, for the fastest service, please submit your form via the
Internet.
For an updated support contact list, see http://www.intel.com/support/9089.htm/
U.S. and Canada
916-377-7000
Europe
Belgium ..... 02 714 3182
Denmark ... 38 487077
Finland ...... 9 693 79297
France ........ 01 41 918529
Germany ... 069 9509 6099
Holland ...... 020 487 4562
Italy ............ 02 696 33276
Norway ...... 23 1620 50
Spain .......... 91 377 8166
Sweden ....... 08 445 1251
UK .............. 870 6072439
In Asia-Pacific region
Australia .... 1800 649931
Cambodia .. 63 2 636 9797 (via Philippines)
China ......... 800 820 1100 (toll-free)
.................... 8 621 33104691 (not toll-free)
Hong Kong 852 2 844 4456
India ........... 0006517 2 68303634 (manual toll-free. You need an IDD-equipped telephone)
Indonesia ... 803 65 7249
Korea ......... 822 767 2595
Malaysia .... 1 800 80 1390
Myanmar ... 63 2 636 9796 (via Philippines)
New Zealand 0800 444 365
Pakistan ..... 632 63684 15 (IDD via Philippines)
Philippines 1 800 1 651 0117
Singapore .. 65 6213-1311
Taiwan ....... 2 2545-1640
Thailand .... 1 800 631 0003
Vietnam ..... 632 6368416 (IDD via Philippines)
Japan
Domestic .... 0120 868686
Outside country 81 298 47 0800
Latin America
Argentina .. Contact AT&T USA at 0-800 222 1288. Once connected, dial 800 843 4481
Brazil ......... 001-916 377 0180
Chile
Easter Island .. ............ Contact AT&T USA at 800 800 311. Once connected, dial 800 843 4481
Mainland and Juan .. Contact AT&T USA at 800 225 288. Once connected, dial 800 843 4481
134 Intel® Server System SR2500AL User’s Guide
Colombia ... Contact AT&T USA at 01 800 911 0010. Once connected, dial 800 843 4481
Costa Rica . Contact AT&T USA at 0 800 0 114 114. Once connected, dial 800 843 4481
Ecuador
(Andimate) .... Contact AT&T USA at 1 999 119. Once connected, dial 800 843 4481
(Pacifictel) ..... Contact AT&T USA at 1 800 225 528. Once connected, dial
800 843 4481
Guatemala . Contact AT&T USA at 99 99 190. Once connected, dial 800 843 4481
Mexico ....... Contact AT&T USA at 001 800 462 628 4240. Once connected, dial 800 843
4481
Miami ........ 1 800 621 8423
Panama ...... Contact AT&T USA at 00 800 001 0109. Once connected, dial 800 843 4481
Paraguay ... 001 916 377 0114
Peru ........... 001 916 377 0114
Uruguay ..... 001 916 377 0114
Venezuela ... Contact AT&T USA at 0 800 2255 288. Once connected, dial 800 843 4481
Intel® Server System SR2500AL User’s Guide 135
136 Intel® Server System SR2500AL User’s Guide
Appendix F: Regulatory and
Compliance Information
Product Regulatory Compliance
Warning: To ensure regulatory compliance, you must adhere to the assembly instructions in this guide to ensure and maintain compliance with existing product certifications and approvals. Use only the described, regulated components specified in this guide. Use of other products/components will void the UL listing and other regulatory approvals of the product and will most likely result in noncompliance with product regulations in the region(s) in which the product is sold.
To help ensure EMC compliance with your local regional rules and regulations, before computer integration, make sure that the server system, power supply, and other modules have passed EMC testing using a server board with a microprocessor from the same family (or higher) and operating at the same (or higher) speed as the microprocessor used on this server board. The final configuration of your end system product may require additional EMC compliance testing. For more information, please contact your local Intel representative.
This is an FCC Class A device. Integration of it into a Class B system does not result in a
Class B device.
Product Safety Compliance
This server chassis product, when correctly integrated per this guide, complies with the following safety and electromagnetic compatibility (EMC) regulations.
Intended Application
This product was evaluated as Information Technology Equipment (ITE), which may be installed in offices, schools, computer rooms, and similar commercial type locations. The suitability of this product for other product categories and environments (such as: medical, industrial, telecommunications, NEBS, residential, alarm systems, test equipment, etc.), other than an ITE application, may require further evaluation.
Product Regulatory Compliance References
The following table references Server Chassis Compliance and markings that may appear on the product. Markings below are typical markings however, may vary or be different based on how certification is obtained.
Note: Certifications Emissions requirements are to Class A.
Table 13. Product Regulatory Compliance Markings
Compliance Regional
Description
Australia / New Zealand
Compliance
Reference
AS/NZS 3548
(Emissions)
Compliance Reference Marking Example
N232
Argentina IRAM
Certification
(Safety)
Belarus Belarus
Certification
Canada / USA CSA 60950 - UL
60950 (Safety)
None Required
Canada / USA
China
Industry Canada
ICES-003
(Emissions)
FCC
CFR 47, Part 15
(Emissions)
CNCA - CB4943
(Safety)
GB 9254
(Emissions)
GB17625
(Harmonics)
CANADA ICES-003 CLASS A
CANADA NMB-003 CLASSE A
138 Intel® Server System SR2500AL User’s Guide
Table 13. Product Regulatory Compliance Markings
Compliance Regional
Description
CENELEC Europe
Germany
Compliance
Reference
Low Voltage
Directive 93/68/
EEC;
EMC Directive 89/
336/EEC
EN55022
(Emissions)
EN55024
(Immunity)
EN61000-3-2
(Harmonics)
EN61000-3-3
(Voltage Flicker)
CE Declaration of
Conformity
GS Certification -
EN60950
Compliance Reference Marking Example
International CB Certification -
IEC60950
CISPR 22 /
CISPR 24
None Required
Japan VCCI Certification
Korea RRL Certification
MIC Notice No.
1997-41 (EMC) &
1997-42 (EMI)
Intel® Server System SR2500AL User’s Guide 139
Table 13. Product Regulatory Compliance Markings
Compliance Regional
Description
Russia
Ukraine
Compliance
Reference
GOST-R
Certification
GOST R 29216-
91 (Emissions)
GOST R 50628-
95 (Immunity)
Ukraine
Certification
Compliance Reference Marking Example
None Required
Taiwan BSMI CNS13438
R33025
140 Intel® Server System SR2500AL User’s Guide
Electromagnetic Compatibility Notices
FCC Verification Statement (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation
5200 N.E. Elam Young Parkway
Hillsboro, OR 97124-6497
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. The customer is responsible for ensuring compliance of the modified product.
Only peripherals (computer input/output devices, terminals, printers, etc.) that comply with FCC Class A or B limits may be attached to this computer product. Operation with noncompliant peripherals is likely to result in interference to radio and TV reception.
All cables used to connect to peripherals must be shielded and grounded. Operation with cables, connected to peripherals, that are not shielded and grounded may result in interference to radio and TV reception.
Intel® Server System SR2500AL User’s Guide 141
Industry Canada (ICES-003)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:
"Apparelis Numériques", NMB-003 édictee par le Ministre Canadian des
Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled: "Digital
Apparatus," ICES-003 of the Canadian Department of Communications.
Europe (CE Declaration of Conformity)
This product has been tested in accordance to, and complies with the Low Voltage
Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate its compliance.
VCCI (Japan)
English translation of the preceding notice:
This is a Class A product based on the standard of the Voluntary Control Council for
Interference (VCCI) from Information Technology Equipment. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
BSMI (Taiwan)
142
The BSMI Certification Marking and EMC warning is located on the outside rear area of the product.
Intel® Server System SR2500AL User’s Guide
Korean Compliance (RRL)
Following is the RRL certification information for Korea.
English translation of the notice above:
1. Type of Equipment (Model Name): On License and Product
2. Certification No.: On RRL certificate. Obtain certificate from local Intel representative
3. Name of Certification Recipient: Intel Corporation
4. Date of Manufacturer: Refer to date code on product
5. Manufacturer/Nation: Intel Corporation/Refer to country of origin marked on product
CNCA (CCC-China)
The CCC Certification Marking and EMC warning is located on the outside rear area of the product.
Product Ecology Compliance
Intel has a system in place to restrict the use of banned substances in accordance with world wide product ecology regulatory requirements. The following is Intel's product ecology compliance criteria.
Intel® Server System SR2500AL User’s Guide 143
144
Table 14. Product Ecology Compliance Markings
Compliance
Regional
Description
California
Compliance Reference
California Code of Regulations, Title 22,
Division 4.5; Chapter 33: Best
Management Practices for Perchlorate
Materials.
Compliance Reference
Marking Example
Special handling may apply. See www.dtsc.ca.gov/ hazardouswaste/perchlorate.
This notice is required by
California Code of Regulations,
Title 22, Division 4.5; Chapter 33:
Best Management Practices for
Perchlorate Materials. This product / part includes a battery which contains Perchlorate material.
China
Intel Internal
Specification
Europe
China RoHS
Administrative Measures on the Control of
Pollution Caused by Electronic Information
Products" (EIP) #39. Referred to as China
RoHS.
Mark requires to be applied to retail products only. Mark used is the
Environmental Friendly Use Period
(EFUP). Number represents years.
China Recycling (GB18455-2001)
Mark requires to be applied to be retail product only. Marking applied to bulk packaging and single packages. Not applied to internal packaging such as plastics, foams, etc.
All materials, parts and subassemblies must not contain restricted materials as defined in Intel's Environmental Product
Content Specification of Suppliers and
Outsourced Manufacturers - http:// supplier.intel.com/ehs/environmental.htm
Waste Electrical and Electronic
Equipment (WEEE) Directive 2002/96/
EC - Mark applied to system level products only.
None Required
Intel® Server System SR2500AL User’s Guide
Compliance
Regional
Description
Europe
Germany
Compliance Reference
European Directive 2002/95/EC -
Restriction of Hazardous Substances
(RoHS). Threshold limits and banned substances are noted below.
Quantity limit of 0.1% by mass (1000
PPM) for: Lead, Mercury, Hexavalent
Chromium, Polybrominated Biphenyls
Diphenyl Ethers (PBB/PBDE)
Quantity limit of 0.01% by mass (100
PPM) for: Cadmium
German Green Dot
Applied to Retail Packaging Only for
Boxed Boards
Intel Internal
Specification
International
All materials, parts and subassemblies must not contain restricted materials as defined in Intel's Environmental Product
Content Specification of Suppliers and
Outsourced Manufacturers - http:// supplier.intel.com/ehs/environmental.htm.
ISO11469 Plastic parts weighing >25gm are intended to be marked with per
ISO11469.
Recycling Markings - Fiberboard (FB) and
Cardboard (CB) are marked with international recycling marks. Applied to outer bulk packaging and single package.
Compliance Reference
Marking Example
None Required.
None Required
>PC/ABS<
Japan Japan Recycling
Applied to Retail Packaging Only for
Boxed Boards
Intel® Server System SR2500AL User’s Guide 145
Other Markings
Table 15. Other Markings
Compliance
Description
Stand-by
Power
Compliance Reference
Stand-by Power Warnings
Applied to product if stand-by power switch is used.
Compliance Reference
Marking Example
Multiple Power
Cords
Multiple Power Cords Warnings
Applied to product if more than one power cord is used.
English:
This unit has more than one power supply cord. To reduce the risk of electrical shock, disconnect (2) two power supply cords before servicing.
Simplified Chinese
’ˆÓ F
为避免遭受电击，
在进行维修之前应断开两（ 2 j
ð电源系统电缆
Traditional Chinese
’ˆÓ F
ðäáô ï³ Ìª £¬
î¤ òä ú¼ë«áó ñý îñ ëë Ó 2 £©
German:
Dieses Geräte hat mehr als ein
Stromkabel. Um eine Gefahr des elektrischen Schlages zu verringern trennen sie beide (2)
Stromkabeln bevor
Instandhaltung
146 Intel® Server System SR2500AL User’s Guide
Compliance
Description
Ground
Connection
Compliance Reference
Ground Connection Warnings
Compliance Reference
Marking Example
Line1 :
“WARNING:”
Swedish on line2:
“Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk."
Finnish on line 3:
"Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan."
English on line 4:
"Connect only to a properly earth grounded outlet."
Regulated Specified Components
To maintain the UL listing and compliance to other regulatory certifications and/or declarations, the following regulated components must be used and conditions adhered to.
Interchanging or use of other components will void the UL listing and other product certifications and approvals.
Updated product information for configurations can be found on the Intel Server Builder
Web site at the following URL: http://channel.intel.com/go/serverbuilder
If you do not have access to Intel's Web address, please contact your local Intel representative.
• Server Chassis: (base chassis is provided with power supply and fans) - UL listed.
• Server board: you must use an Intel server board - UL recognized.
• Add-in boards: must have a printed wiring board flammability rating of minimum
UL94V-1. Add-in boards containing external power connectors and/or lithium batteries must be UL recognized or UL listed. Any add-in board containing modem telecommunication circuitry must be UL listed. In addition, the modem must have the appropriate telecommunications, safety, and EMC approvals for the region in which it is sold.
• Peripheral Storage Devices: must be a UL recognized or UL listed accessory and
TUV or VDE licensed. Total server configuration is not to exceed the maximum loading conditions of the power supply.
Intel® Server System SR2500AL User’s Guide 147
End-of-Life / Product Recycling
Product recycling and end-of-life take-back systems and requirements vary by country.
Contact the retailer or distributor of this product for information about product recycling and / or take-back.
148 Intel® Server System SR2500AL User’s Guide
Appendix G: Warranty
Limited Warranty for Intel® Chassis
Subassembly Products
Intel warrants that the Products (defined herein as the Intel® chassis subassembly and all of its various components and software delivered with or as part of the Products) to be delivered hereunder, if properly used and installed, will be free from defects in material and workmanship and will substantially conform to Intel's publicly available specifications for a period of three (3) years after the date the Product was purchased from an Intel authorized distributor. Software of any kind delivered with or as part of products is expressly provided "as is" unless specifically provided for otherwise in any software license accompanying the software.
If any Product furnished by Intel which is the subject of this Limited Warranty fails during the warranty period for reasons covered by this Limited Warranty, Intel, at its option, will:
• REPAIR the Product by means of hardware and/or software; OR
• REPLACE the Product with another Product; OR
• REFUND the then-current value of the Product if Intel is unable to repair or replace the Product.
If such Product is defective, transportation charges for the return of Product to buyer within the USA will be paid by Intel. For all other locations, the warranty excludes all costs of shipping, customs clearance, and other related charges. Intel will have a reasonable time to make repairs or to replace Product or to refund the then-current value of the Product.
In no event will Intel be liable for any other costs associated with the replacement or repair of Product, including labor, installation or other costs incurred by buyer and in particular, any costs relating to the removal or replacement of any product soldered or otherwise permanently affixed to any printed circuit board.
This Limited Warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of the Product.
Extent of Limited Warranty
Intel does not warrant that Products to be delivered hereunder, whether delivered standalone or integrated with other Products, including without limitation semiconductor components, will be free from design defects or errors known as "errata." Current characterized errata are available upon request.
This Limited Warranty does not cover damages due to external causes, including accident, problems with electrical power, usage not in accordance with product instructions, misuse, neglect, alteration, repair, improper installation, or improper testing.
Warranty Limitations and Exclusions
These warranties replace all other warranties, expressed or implied including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Intel makes no expressed warranties beyond those stated here. Intel disclaims all other warranties, expressed or implied including, without limitation, implied warranties of merchantability and fitness for a particular purpose. Some jurisdictions do not allow the exclusion of implied warranties, so this limitation may not apply.
All expressed and implied warranties are limited in duration to the limited warranty period. No warranties apply after that period. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you.
Limitations of Liability
Intel's responsibility under this, or any other warranty, implied or expressed, is limited to repair, replacement, or refund, as set forth above. These remedies are the sole and exclusive remedies for any breach of warranty. Intel is not responsible for direct, special, incidental, or consequential damages resulting from any breach of warranty under another legal theory including, but not limited to, lost profits, downtime, goodwill, damage to or replacement of equipment and property, and any costs of recovering, reprogramming, or reproducing any program or data stored in or used with a system containing this product.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights that vary from jurisdiction to jurisdiction.
Any and all disputes arising under or related to this Limited Warranty shall be adjudicated in the following forums and governed by the following laws: for the United States of
America, Canada, North America, and South America, the forum shall be Santa Clara,
California, USA, and the applicable law shall be that of the State of California, USA; for the Asia Pacific region, the forum shall be Singapore and the applicable law shall be that of Singapore; for Europe and the rest of the world, the forum shall be London and the applicable law shall be that of the United Kingdom.
In the event of any conflict between the English language version and any other translated version(s) of this Limited Warranty, the English language version shall control.
How to Obtain Warranty Service
To obtain warranty service for this Product, you may contact Intel or your authorized distributor.
150 Intel® Server System SR2500AL User’s Guide
• North America and Latin America To obtain warranty repair for the product, please go to the following Web site to obtain instructions: http://support.intel.com/support/ motherboards/draform.htm
• In Europe and in Asia Contact your original authorized distributor for warranty service.
Any replacement Product is warranted under this written warranty and is subject to the same limitations and exclusions for the remainder of the original warranty period.
Telephone Support
If you cannot find the information you need on Intel's World Wide Web site (http:// www.intel.com/), call your local distributor or an Intel Customer Support representative.
See “Getting Help” for telephone numbers.
Returning a Defective Product
Before returning any product, call your authorized dealer/distribution authority.
Intel® Server System SR2500AL User’s Guide 151
152 Intel® Server System SR2500AL User’s Guide
Appendix H: Installation/Assembly
Safety Instructions
English
The power supply in this product contains no user-serviceable parts. Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product with more than one power supply will have a separate AC power cord for each supply.
The power button on the system does not turn off system AC power. To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power supply.
The power cord(s) is considered the disconnect device to the main
(AC) power. The socket outlet that the system plugs into shall be installed near the equipment and shall be easily accessible.
SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall outlets.
4. Label and disconnect all cables connected to I/O connectors or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap attached to chassis ground of the system-any unpainted metal surface-when handling components.
6. Do not operate the system with the chassis covers removed.
Intel® Server System SR2500AL User’s Guide 153
154
After you have completed the six SAFETY steps above, you can remove the system covers. To do this:
1. Unlock and remove the padlock from the back of the system if a padlock has been installed.
2. Remove and save all screws from the covers.
3. Remove the cover(s).
For proper cooling and airflow, always reinstall the chassis covers before turning on the system. Operating the system without the covers in place can damage system parts. To install the covers:
1. Check first to make sure you have not left loose tools or parts inside the system.
2. Check that cables, add-in boards, and other components are properly installed.
3. Attach the covers to the chassis with the screws removed earlier, and tighten them firmly.
4. Insert and lock the padlock to the system to prevent unauthorized access inside the system.
5. Connect all external cables and the AC power cord(s) to the system.
A microprocessor and heat sink may be hot if the system has been running. Also, there may be sharp pins and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves.
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Dispose of used batteries according to manufacturer's instructions.
The system is designed to operate in a typical office environment.
Choose a site that is:
•
Clean and free of airborne particles (other than normal room dust).
•
Well ventilated and away from sources of heat including direct sunlight.
•
Away from sources of vibration or physical shock.
•
Isolated from strong electromagnetic fields produced by electrical devices.
•
In regions that are susceptible to electrical storms, we recommend you plug your system into a surge suppresser and disconnect telecommunication lines to your modem during an electrical storm.
•
Provided with a properly grounded wall outlet.
•
Provided with sufficient space to access the power supply cord(s), because they serve as the product's main power disconnect.
Intel® Server System SR2500AL User’s Guide
Deutsch
Benutzer können am Netzgerät dieses Produkts keine Reparaturen vornehmen. Das Produkt enthält möglicherweise mehrere
Netzgeräte. Wartungsarbeiten müssen von qualifizierten
Technikern ausgeführt werden.
Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu verwenden, wenn es sich nicht genau um den erforderlichen Typ handelt. Ein Produkt mit mehreren Netzgeräten hat für jedes
Netzgerät ein eigenes Netzkabel.
Der Wechselstrom des Systems wird durch den Ein-/Aus-Schalter für Gleichstrom nicht ausgeschaltet. Ziehen Sie jedes
Wechselstrom-Netzkabel aus der Steckdose bzw. dem Netzgerät, um den Stromanschluß des Systems zu unterbrechen.
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus der Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um elektrostatische Ladungen (ESD) über blanke Metallstellen bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß montiertes Gehäuse ein.
Intel® Server System SR2500AL User’s Guide 155
156
SICHERHEISMASSNAHMEN: Immer wenn Sie die
Gehäuseabdeckung abnehmen um an das Systeminnere zu gelangen, sollten Sie folgende Schritte beachten:
1. Schalten Sie alle an Ihr System angeschlossenen
Peripheriegeräte aus.
2. Schalten Sie das System mit dem Hauptschalter aus.
3. Ziehen Sie den Stromanschlußstecker Ihres Systems aus der Steckdose.
4. Auf der Rückseite des Systems beschriften und ziehen Sie alle Anschlußkabel von den I/O Anschlüssen oder Ports ab.
5. Tragen Sie ein geerdetes Antistatik Gelenkband, um elektrostatische Ladungen (ESD) über blanke Metallstellen bei der Handhabung der Komponenten zu vermeiden.
6. Schalten Sie das System niemals ohne ordnungsgemäß montiertes Gehäuse ein.
Zur ordnungsgemäßen Kühlung und Lüftung muß die
Gehäuseabdeckung immer wieder vor dem Einschalten installiert werden. Ein Betrieb des Systems ohne angebrachte Abdeckung kann Ihrem System oder Teile darin beschädigen. Um die
Abdeckung wieder anzubringen:
1. Vergewissern Sie sich, daß Sie keine Werkzeuge oder Teile im Innern des Systems zurückgelassen haben.
2. Überprüfen Sie alle Kabel, Zusatzkarten und andere
Komponenten auf ordnungsgemäßen Sitz und Installation.
3. Bringen Sie die Abdeckungen wieder am Gehäuse an, indem
Sie die zuvor gelösten Schrauben wieder anbringen. Ziehen
Sie diese gut an.
4. Bringen Sie die Verschlußeinrichtung (Padlock) wieder an und schließen Sie diese, um ein unerlaubtes Öffnen des
Systems zu verhindern.
5. Schließen Sie alle externen Kabel und den AC
Stromanschlußstecker Ihres Systems wieder an.
Der Mikroprozessor und der Kühler sind möglicherweise erhitzt, wenn das System in Betrieb ist. Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen.
Bei falschem Einsetzen einer neuen Batterie besteht
Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.
Intel® Server System SR2500AL User’s Guide
Français
Das System wurde für den Betrieb in einer normalen
Büroumgebung entwickelt. Der Standort sollte:
•
"sauber und staubfrei sein (Hausstaub ausgenommen);
•
"gut gelüftet und keinen Heizquellen ausgesetzt sein
(einschließlich direkter Sonneneinstrahlung);
•
"keinen Erschütterungen ausgesetzt sein;
•
"keine starken, von elektrischen Geräten erzeugten elektromagnetischen Felder aufweisen;
•
"in Regionen, in denen elektrische Stürme auftreten, mit einem
Überspannungsschutzgerät verbunden sein; während eines elektrischen Sturms sollte keine Verbindung der
Telekommunikationsleitungen mit dem Modem bestehen;
•
"mit einer geerdeten Wechselstromsteckdose ausgerüstet sein;
•
"über ausreichend Platz verfügen, um Zugang zu den
Netzkabeln zu gewährleisten, da der Stromanschluß des
Produkts hauptsächlich über die Kabel unterbrochen wird
Le bloc d'alimentation de ce produit ne contient aucune pièce pouvant être réparée par l'utilisateur. Ce produit peut contenir plus d'un bloc d'alimentation. Veuillez contacter un technicien qualifié en cas de problème.
Ne pas essayer d'utiliser ni modifier le câble d'alimentation CA fourni, s'il ne correspond pas exactement au type requis. Le nombre de câbles d'alimentation CA fournis correspond au nombre de blocs d'alimentation du produit
Notez que le commutateur CC de mise sous tension /hors tension du panneau avant n'éteint pas l'alimentation CA du système. Pour mettre le système hors tension, vous devez débrancher chaque câble d'alimentation de sa prise.
Intel® Server System SR2500AL User’s Guide 157
158
CONSIGNES DE SÉCURITÉ -Lorsque vous ouvrez le boîtier pour accéder à l'intérieur du système, suivez les consignes suivantes:
1. Mettez hors tension tous les périphériques connectés au système.
2. Mettez le système hors tension en mettant l'interrupteur général en position OFF (bouton-poussoir).
3. Débranchez tous les cordons d'alimentation c.a. du système et des prises murales.
4. Identifiez et débranchez tous les câbles reliés aux connecteurs d'E-S ou aux accès derrière le système.
5. Pour prévenir les décharges électrostatiques lorsque vous touchez aux composants, portez une bande antistatique pour poignet et reliez-la à la masse du système (toute surface métallique non peinte du boîtier).
6. Ne faites pas fonctionner le système tandis que le boîtier est ouvert.
Une fois TOUTES les étapes précédentes accomplies, vous pouvez retirer les panneaux du système. Procédez comme suit:
1. Si un cadenas a été installé sur à l'arrière du système, déverrouillez-le et retirez-le.
2. Retirez toutes les vis des panneaux et mettez-les dans un endroit sûr.
3. Retirez les panneaux.
Afin de permettre le refroidissement et l'aération du système, réinstallez toujours les panneaux du boîtier avant de mettre le système sous tension. Le fonctionnement du système en l'absence des panneaux risque d'endommager ses pièces. Pour installer les panneaux, procédez comme suit:
1. Assurez-vous de ne pas avoir oublié d'outils ou de pièces démontées dans le système.
2. Assurez-vous que les câbles, les cartes d'extension et les autres composants sont bien installés.
3. Revissez solidement les panneaux du boîtier avec les vis retirées plus tôt.
4. Remettez le cadenas en place et verrouillez-le afin de prévenir tout accès non autorisé à l'intérieur du système.
5. Rebranchez tous les cordons d'alimentation c. a. et câbles externes au système.
Le microprocesseur et le dissipateur de chaleur peuvent être chauds si le système a été sous tension. Faites également attention aux broches aiguës des cartes et aux bords tranchants du capot.
Nous vous recommandons l'usage de gants de protection.
Intel® Server System SR2500AL User’s Guide
Español
Danger d'explosion si la batterie n'est pas remontée correctement.
Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé par le fabricant. Disposez des piles usées selon les instructions du fabricant.
Le système a été conçu pour fonctionner dans un cadre de travail normal. L'emplacement choisi doit être:
•
"Propre et dépourvu de poussière en suspension (sauf la poussière normale).
•
"Bien aéré et loin des sources de chaleur, y compris du soleil direct.
•
"A l'abri des chocs et des sources de vibrations.
•
"Isolé de forts champs électromagnétiques géenérés par des appareils électriques.
•
"Dans les régions sujettes aux orages magnétiques il est recomandé de brancher votre système à un supresseur de surtension, et de débrancher toutes les lignes de télécommunications de votre modem durant un orage.
•
"Muni d'une prise murale correctement mise à la terre.
•
"Suffisamment spacieux pour vous permettre d'accéder aux câbles d'alimentation (ceux-ci étant le seul moyen de mettre le système hors tension).
El usuario debe abstenerse de manipular los componentes de la fuente de alimentación de este producto, cuya reparación debe dejarse exclusivamente en manos de personal técnico especializado. Puede que este producto disponga de más de una fuente de alimentación
No intente modificar ni usar el cable de alimentación de corriente alterna, si no corresponde exactamente con el tipo requerido.
El número de cables suministrados se corresponden con el número de fuentes de alimentación de corriente alterna que tenga el producto
Intel® Server System SR2500AL User’s Guide 159
160
Nótese que el interruptor activado/desactivado en el panel frontal no desconecta la corriente alterna del sistema. Para desconectarla, deberá desenchufar todos los cables de corriente alterna de la pared o desconectar la fuente de alimentación.
INSTRUCCIONES DE SEGURIDAD: Cuando extraiga la tapa del chasis para acceder al interior del sistema, siga las siguientes instrucciones:
1. Apague todos los dispositivos periféricos conectados al sistema.
2. Apague el sistema presionando el interruptor encendido/ apagado.
3. Desconecte todos los cables de alimentación CA del sistema o de las tomas de corriente alterna.
4. Identifique y desconecte todos los cables enchufados a los conectores E/S o a los puertos situados en la parte posterior del sistema.
5. Cuando manipule los componentes, es importante protegerse contra la descarga electrostática (ESD). Puede hacerlo si utiliza una muñequera antiestática sujetada a la toma de tierra del chasis - o a cualquier tipo de superficie de metal sin pintar.
6. No ponga en marcha el sistema si se han extraído las tapas del chasis.
Después de completar las seis instrucciones de SEGURIDAD mencionadas, ya puede extraer las tapas del sistema. Para ello:
1. Desbloquee y extraiga el bloqueo de seguridad de la parte posterior del sistema, si se ha instalado uno.
2. Extraiga y guarde todos los tornillos de las tapas.Extraiga las tapas.
Para obtener un enfriamiento y un flujo de aire adecuados, reinstale siempre las tapas del chasis antes de poner en marcha el sistema. Si pone en funcionamiento el sistema sin las tapas bien colocadas puede dañar los componentes del sistema. Para instalar las tapas:
1. Asegúrese primero de no haber dejado herramientas o componentes sueltos dentro del sistema.
2. Compruebe que los cables, las placas adicionales y otros componentes se hayan instalado correctamente.
3. Incorpore las tapas al chasis mediante los tornillos extraídos anteriormente, tensándolos firmemente.
4. Inserte el bloqueo de seguridad en el sistema y bloquéelo para impedir que pueda accederse al mismo sin autorización.
5. Conecte todos los cables externos y los cables de alimentación CA al sistema.
Intel® Server System SR2500AL User’s Guide
Chinese
Si el sistema ha estado en funcionamiento, el microprocesador y el disipador de calor pueden estar aún calientes. También conviene tener en cuenta que en el chasis o en el tablero puede haber piezas cortantes o punzantes. Por ello, se recomienda precaución y el uso de guantes protectores.
Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante.
El sistema está diseñado para funcionar en un entorno de trabajo normal. Escoja un lugar:
•
"Limpio y libre de partículas en suspensión (salvo el polvo normal).
•
"Bien ventilado y alejado de fuentes de calor, incluida la luz solar directa.
•
"Alejado de fuentes de vibración.
•
"Aislado de campos electromagnéticos fuertes producidos por dispositivos eléctricos.
•
"En regiones con frecuentes tormentas eléctricas, se recomienda conectar su sistema a un eliminador de sobrevoltage y desconectar el módem de las líneas de telecomunicación durante las tormentas.
•
"Provisto de una toma de tierra correctamente instalada.
•
"Provisto de espacio suficiente como para acceder a los cables de alimentación, ya que éstos hacen de medio principal de desconexión del sistema.
Intel® Server System SR2500AL User’s Guide 161
Italiano
162
Rivolgersi ad un tecnico specializzato per la riparazione dei componenti dell'alimentazione di questo prodotto. È possibile che il prodotto disponga di più fonti di alimentazione.
Non modificare o utilizzare il cavo di alimentazione in c.a. fornito dal produttore, se non corrisponde esattamente al tipo richiesto. Ad ogni fonte di alimentazione corrisponde un cavo di alimentazione in c.a. separato
L'interruttore attivato/disattivato nel pannello anteriore non interrompe l'alimentazione in c.a. del sistema. Per interromperla, è necessario scollegare tutti i cavi di alimentazione in c.a. dalle prese a muro o dall'alimentazione di corrente.
PASSI DI SICUREZZA: Qualora si rimuovano le coperture del telaio per accedere all'interno del sistema, seguire i seguenti passi:
1. Spegnere tutti i dispositivi periferici collegati al sistema.
2. Spegnere il sistema, usando il pulsante spento/acceso dell'interruttore del sistema.
3. Togliere tutte le spine dei cavi del sistema dalle prese elettriche.
4. Identificare e sconnettere tutti i cavi attaccati ai collegamenti
I/O od alle prese installate sul retro del sistema.
5. Qualora si tocchino i componenti, proteggersi dallo scarico elettrostatico (SES), portando un cinghia anti-statica da polso che è attaccata alla presa a terra del telaio del sistema
- qualsiasi superficie non dipinta - .
6. Non far operare il sistema quando il telaio è senza le coperture.
Dopo aver seguito i sei passi di SICUREZZA sopracitati, togliere le coperture del telaio del sistema come seque:
1. Aprire e rimuovere il lucchetto dal retro del sistema qualora ve ne fosse uno installato.
2. Togliere e mettere in un posto sicuro tutte le viti delle coperture.
3. Togliere le coperture.
Intel® Server System SR2500AL User’s Guide
Per il giusto flusso dell'aria e raffreddamento del sistema, rimettere sempre le coperture del telaio prima di riaccendere il sistema.
Operare il sistema senza le coperture al loro proprio posto potrebbe danneggiare i componenti del sistema. Per rimettere le coperture del telaio:
1. Controllare prima che non si siano lasciati degli attrezzi o dei componenti dentro il sistema.
2. Controllare che i cavi, dei supporti aggiuntivi ed altri componenti siano stati installati appropriatamente.
3. Attaccare le coperture al telaio con le viti tolte in precedenza e avvitarle strettamente.
4. Inserire e chiudere a chiave il lucchetto sul retro del sistema per impedire l'accesso non autorizzato al sistema.
5. Ricollegare tutti i cavi esterni e le prolunghe AC del sistema.
Se il sistema è stato a lungo in funzione, il microprocessore e il dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l'uso di guanti di protezione.
Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore.
Il sistema è progettato per funzionare in un ambiente di lavoro tipo.
Scegliere una postazione che sia:
•
"Pulita e libera da particelle in sospensione (a parte la normale polvere presente nell'ambiente).
•
"Ben ventilata e lontana da fonti di calore, compresa la luce solare diretta.
•
"Al riparo da urti e lontana da fonti di vibrazione.
•
"Isolata dai forti campi magnetici prodotti da dispositivi elettrici.
•
"In aree soggette a temporali, è consigliabile collegare il sistema ad un limitatore di corrente. In caso di temporali, scollegare le linee di comunicazione dal modem.
•
"Dotata di una presa a muro correttamente installata.
•
"Dotata di spazio sufficiente ad accedere ai cavi di alimentazione, i quali rappresentano il mezzo principale di scollegamento del sistema.
Intel® Server System SR2500AL User’s Guide 163
164 Intel® Server System SR2500AL User’s Guide
Appendix I: Safety Information
English
Server Safety Information
This document applies to Intel ® server boards, Intel ® server chassis (pedestal and rackmount) and installed peripherals. To reduce the risk of bodily injury, electrical shock, fire, and equipment damage, read this document and observe all warnings and precautions in this guide before installing or maintaining your Intel ® server product.
In the event of a conflict between the information in this document and information provided with the product or on the website for a particular product, the product documentation takes precedence.
Your server should be integrated and serviced only by technically qualified persons.
You must adhere to the guidelines in this guide and the assembly instructions in your server manuals to ensure and maintain compliance with existing product certifications and approvals. Use only the described, regulated components specified in this guide. Use of other products / components will void the UL Listing and other regulatory approvals of the product, and may result in noncompliance with product regulations in the region(s) in which the product is sold.
Safety Warnings and Cautions
To avoid personal injury or property damage, before you begin installing the product, read, observe, and adhere to all of the following safety instructions and information. The following safety symbols may be used throughout the documentation and may be marked on the product and / or the product packaging.
CAUTION
WARNING
Indicates the presence of a hazard that may cause minor personal injury or property damage if the CAUTION is ignored.
Indicates the presence of a hazard that may result in serious personal injury if the WARNING is ignored.
Indicates potential hazard if indicated information is ignored.
Indicates shock hazards that result in serious injury or death if safety instructions are not followed.
Indicates hot components or surfaces.
Intel® Server System SR2500AL User’s Guide 165
Indicates do not touch fan blades, may result in injury.
Indicates to unplug all AC power cord(s) to disconnect AC power
Please recycle battery
Intended Application Uses
This product was evaluated as Information Technology Equipment (ITE), which may be installed in offices, schools, computer rooms, and similar commercial type locations. The suitability of this product for other product categories and environments (such as medical, industrial, residential, alarm systems, and test equipment), other than an ITE application, may require further evaluation.
Site Selection
The system is designed to operate in a typical office environment. Choose a site that is:
• Clean, dry, and free of airborne particles (other than normal room dust).
• Well-ventilated and away from sources of heat including direct sunlight and radiators.
• Away from sources of vibration or physical shock.
• Isolated from strong electromagnetic fields produced by electrical devices.
• In regions that are susceptible to electrical storms, we recommend you plug your system into a surge suppresser and disconnect telecommunication lines to your modem during an electrical storm.
• Provided with a properly grounded wall outlet.
• Provided with sufficient space to access the power supply cord(s), because they serve as the product's main power disconnect.
Equipment Handling Practices
Reduce the risk of personal injury or equipment damage:
• Conform to local occupational health and safety requirements when moving and lifting equipment.
• Use mechanical assistance or other suitable assistance when moving and lifting equipment.
• To reduce the weight for easier handling, remove any easily detachable components.
166 Intel® Server System SR2500AL User’s Guide
Power and Electrical Warnings
Caution: The power button, indicated by the stand-by power marking, DOES NOT completely turn off the system AC power, 5V standby power is active whenever the system is plugged in.
To remove power from system, you must unplug the AC power cord from the wall outlet.
Your system may use more than one AC power cord. Make sure all AC power cords are unplugged. Make sure the AC power cord(s) is/are unplugged before you open the chassis, or add or remove any non hot-plug components.
Do not attempt to modify or use an AC power cord if it is not the exact type required. A separate AC cord is required for each system power supply.
Some power supplies in Intel
®
servers use Neutral Pole Fusing. To avoid risk of shock use caution when working with power supplies that use Neutral Pole Fusing.
The power supply in this product contains no user-serviceable parts. Do not open the power supply. Hazardous voltage, current and energy levels are present inside the power supply. Return to manufacturer for servicing.
When replacing a hot-plug power supply, unplug the power cord to the power supply being replaced before removing it from the server.
To avoid risk of electric shock, turn off the server and disconnect the power cord, telecommunications systems, networks, and modems attached to the server before opening it.
Power Cord Warnings
If an AC power cord was not provided with your product, purchase one that is approved for use in your country.
Caution: To avoid electrical shock or fire, check the power cord(s) that will be used with the product as follows:
• Do not attempt to modify or use the AC power cord(s) if they are not the exact type required to fit into the grounded electrical outlets
• The power cord(s) must meet the following criteria:
• The power cord must have an electrical rating that is greater than that of the electrical current rating marked on the product.
• The power cord must have safety ground pin or contact that is suitable for the electrical outlet.
• The power supply cord(s) is/are the main disconnect device to AC power. The socket outlet(s) must be near the equipment and readily accessible for disconnection.
• The power supply cord(s) must be plugged into socket-outlet(s) that is /are provided with a suitable earth ground.
Intel® Server System SR2500AL User’s Guide 167
System Access Warnings
Caution: To avoid personal injury or property damage, the following safety instructions apply whenever accessing the inside of the product:
• Turn off all peripheral devices connected to this product.
• Turn off the system by pressing the power button to off.
• Disconnect the AC power by unplugging all AC power cords from the system or wall outlet.
• Disconnect all cables and telecommunication lines that are connected to the system.
• Retain all screws or other fasteners when removing access cover(s). Upon completion of accessing inside the product, refasten access cover with original screws or fasteners.
• Do not access the inside of the power supply. There are no serviceable parts in the power supply. Return to manufacturer for servicing.
• Power down the server and disconnect all power cords before adding or replacing any non hot-plug component.
• When replacing a hot-plug power supply, unplug the power cord to the power supply being replaced before removing the power supply from the server.
Caution: If the server has been running, any installed processor(s) and heat sink(s) may be hot.
Unless you are adding or removing a hot-plug component, allow the system to cool before opening the covers. To avoid the possibility of coming into contact with hot component(s) during a hot-plug installation, be careful when removing or installing the hot-plug component(s).
Caution: To avoid injury do not contact moving fan blades. If your system is supplied with a guard over the fan, do not operate the system without the fan guard in place.
Rack Mount Warnings
The equipment rack must be anchored to an unmovable support to prevent it from tipping when a server or piece of equipment is extended from it. The equipment rack must be installed according to the rack manufacturer's instructions.
Install equipment in the rack from the bottom up, with the heaviest equipment at the bottom of the rack.
Extend only one piece of equipment from the rack at a time.
You are responsible for installing a main power disconnect for the entire rack unit. This main disconnect must be readily accessible, and it must be labeled as controlling power to the entire unit, not just to the server(s).
To avoid risk of potential electric shock, a proper safety ground must be implemented for the rack and each piece of equipment installed in it.
168 Intel® Server System SR2500AL User’s Guide
Electrostatic Discharge (ESD)
Caution: ESD can damage disk drives, boards, and other parts. We recommend that you perform all procedures at an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground -- any unpainted metal surface -- on your server when handling parts.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a board from its protective wrapper or from the server, place the board component side up on a grounded, static free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
Other Hazards
Battery Replacement
Caution: There is the danger of explosion if the battery is incorrectly replaced. When replacing the battery, use only the battery recommended by the equipment manufacturer.
Dispose of batteries according to local ordinances and regulations.
Do not attempt to recharge a battery.
Do not attempt to disassemble, puncture, or otherwise damage a battery.
Cooling and Airflow
Caution: Carefully route cables as directed to minimize airflow blockage and cooling problems.
For proper cooling and airflow, operate the system only with the chassis covers installed.
Operating the system without the covers in place can damage system parts. To install the covers:
• Check first to make sure you have not left loose tools or parts inside the system.
• Check that cables, add-in boards, and other components are properly installed.
• Attach the covers to the chassis according to the product instructions.
Laser Peripherals or Devices
Caution: To avoid risk of radiation exposure and/or personal injury:
• Do not open the enclosure of any laser peripheral or device
• Laser peripherals or devices have are not user serviceable
• Return to manufacturer for servicing
Intel® Server System SR2500AL User’s Guide 169
Deutsch
Sicherheitshinweise für den Server
Das vorliegende Dokument bezieht sich auf Intel ® Serverplatinen, Intel ® Servergehäuse
(Standfuß und Rack) sowie installierte Peripheriegeräte. Es enthält Warnungen und
Vorsichtsmaßnahmen zur Vermeidung von Gefahren durch Verletzung, Stromschlag,
Feuer und Beschädigungen von Geräten. Lesen Sie diese Dokument daher sorgfältig, bevor Sie Ihr Intel ® Serverprodukt installieren oder warten.
Bei Widersprüchen zwischen den hier vorliegenden Angaben und den Informationen im
Lieferumfang des Produkts oder auf der Website des betreffenden Produkts hat die
Produktdokumentation Vorrang.
Die Integration und Wartung des Servers darf nur durch technisch qualifizierte Personen erfolgen.
Um die Einhaltung der vorhandenen Zulassungen und Genehmigungen für das Produkt zu gewährleisten, sind die Richtlinien in diesem Handbuch sowie die Montageanleitungen in den Serverhandbüchern zu beachten. Verwenden Sie nur die beschriebenen, zugelassenen
Komponenten, die im vorliegenden Handbuch angegeben werden. Die Verwendung anderer Produkte oder Komponenten führt zum Erlöschen der UL-Zulassung und anderer
Genehmigungen für das Produkt. Dadurch kann das Produkt gegen Produktbestimmungen verstoßen, die im Verkaufsland gelten.
Sicherheitshinweise und Vorsichtsmaßnahmen
Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor dem Beginn der
Produktinstallation die nachfolgend aufgeführten Sicherheitshinweise und -informationen sorgfältig lesen und befolgen. In dem vorliegenden Handbuch sowie auf dem Produkt und auf der Verpackung werden folgende Sicherheitssymbole verwendet:
170
VORSICHT
WARNUNG
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung des
VORSICHTSHINWEISES zu leichteren Verletzungen bzw.
Sachbeschädigungen führen kann.
Weist auf eine Gefahrenquelle hin, die bei Nichtbeachtung der WARNUNG zu ernsten Verletzungen führen kann.
Weist auf potentielle Gefahr bei Nichtbeachtung der angezeigten
Informationen hin.
Weist auf die Gefahr eines Stromschlags hin, der bei Nichtbeachtung der
Sicherheitshinweise zu schweren oder tödlichen Verletzungen führen kann.
Weist auf Verbrennungsgefahr an heißen Bauteilen bzw. Oberflächen hin.
Intel® Server System SR2500AL User’s Guide
Weist darauf hin, daß das Anfassen des Gebläses zu Verletzungen führen kann.
Bedeutet, alle Netzkabel abzuziehen und das Gerät von der Netzspannung zu trennen.
Bereiten Sie bitte Batterie auf
Zielbenutzer der Anwendung
Dieses Produkt wurde in seiner Eigenschaft als IT-Gerät getestet, das in Büros, Schulen,
Computerräumen und ähnlichen öffentlichen Räumlichkeiten installiert werden kann. Die
Eignung dieses Produkts für andere Einsatzbereiche als IT (z. B. Medizin, Industrie,
Alarmsysteme oder Prüfgeräte) kann u. U. weitere Tests erfordern.
Standortauswahl
Das System ist für den Betrieb innerhalb normaler Büroumgebungen geeignet. Wählen
Sie einen Standort, der folgenden Kriterien entspricht:
• Sauber, trocken und frei von Partikeln in der Luft (außer dem normalen Raumstaub).
• Gut belüftet, nicht in der Nähe von Wärmequellen und keiner direkten
Sonnenbestrahlung ausgesetzt.
• Nicht in der Nähe von Vibrations- oder Erschütterungsquellen.
• Abgeschirmt von starken elektromagnetischen Feldern, die durch elektrische Geräte erzeugt werden.
• In gewittergefährdeten Gebieten sollten Sie das System an einen
Überspannungsschutz anschließen und bei einem Gewitter die
Telekommunikationskabel zum Modem abziehen.
• Eine ordnungsgemäß geerdete Wandsteckdose muß vorhanden sein.
• Ausreichender Freiraum für den Zugang zu den Netzkabeln, da diese die
Hauptvorrichtung zum Trennen des Produkts von der Stromversorgung sind.
Handhabung von Geräten
Beachten Sie zur Vermeidung von Verletzungen oder Beschädigungen an den Geräten die folgenden Hinweise:
• Halten Sie beim Transportieren und Anheben von Geräten die örtlichen
Gesundheits- und Sicherheitsvorschriften ein.
• Verwenden Sie mechanische oder andere geeignete Hilfsmittel zum Transportieren oder Anheben von Geräten.
• Entfernen Sie alle Komponenten, die sich leicht abnehmen lassen, um das Gewicht zu reduzieren und die Handhabung zu erleichtern.
Intel® Server System SR2500AL User’s Guide 171
Warnungen zu Netzspannung und Elektrizität
Caution: Durch Betätigen der mit dem Standby-Symbol gekennzeichneten Netztaste wird das
System NICHT vollständig vom Netz getrennt. Es sind weiterhin 5 V aktiv, solange das
System eingesteckt ist. Um das System vollständig vom Strom zu trennen, muß das
Netzkabel aus der Steckdose abgezogen werden. Das System verfügt möglicherweise über mehrere Netzkabel. Vergewissern Sie sich in diesem Fall, daß alle Netzkabel abgezogen sind. Wenn Sie Komponenten ein- oder ausbauen möchten, die nicht hot-plug-fähig sind, stellen Sie sicher, daß zuvor alle Netzkabel abgezogen sind.
Nehmen Sie keine Änderungen am Netzkabel vor, und verwenden Sie kein Kabel, das nicht genau dem geforderten Typ entspricht. Jedes Netzteil im System muß über ein eigenes
Netzkabel angeschlossen werden.
Einige Netzteile von Intel Servern verwenden Nullleitersicherungen. Vorsicht ist geboten im Umgang mit Netzteilen, welche Nullleitersicherungen verwenden, um das Risiko eines elektrischen Schlages zu vermeiden
Das Netzteil in diesem Produkt enthält keine Teile, die vom Benutzer gewartet werden können. Öffnen Sie das Netzteil nicht. Im Netzteil bestehen gefährliche Spannungen,
Ströme und Energiequellen. Schicken Sie das Gerät für Wartungsarbeiten an den
Hersteller zurück.
Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab, bevor
Sie es aus dem Server ausbauen.
Zur Vermeidung von Stromschlägen schalten Sie den Server aus, und trennen Sie vor dem
Öffnen des Geräts das Netzkabel sowie alle an den Server angeschlossene
Telekommunikationssysteme, Netzwerke und Modems.
Hinweis für Netzkabel
Wenn kein Netzkabel mit dem Produkt geliefert wurde, kaufen Sie ein Kabel, das für die
Caution: Prüfen Sie zur Vermeidung von Stromschlag oder Feuergefahr die mit dem Produkt zu verwendenden Netzkabel wie folgt:
• Nehmen Sie keine Änderungen an einem Netzkabel vor, und benutzen sie es nicht, wenn es nicht genau in die geerdeten Netzsteckdosen paßt.
• Netzkabel müssen die folgenden Anforderungen erfüllen:
— Die Nennbelastbarkeit des Netzkabels muß mindestens so hoch sein wie die am
Produkt angegebenen Nennstromaufnahme.
— Das Netzkabel muß einen zur Netzsteckdose passenden Schutzkontakt besitzen.
• Die Netzkabel sind die Hauptvorrichtung zum Trennen des Geräts vom Stromnetz.
Die Steckdose muß in der Nähe der Anlage angebracht und gut erreichbar sein.
• Netzkabel müssen an eine ordnungsgemäß geerdete Steckdose angeschlossen sein.
172 Intel® Server System SR2500AL User’s Guide
Warnhinweise für den Systemzugang
Caution: Um Verletzungen und Beschädigungen zu vermeiden, sollten Sie vor Arbeiten im
Produktinneren folgende Sicherheitsanweisungen beachten:
• Schalten Sie alle am Produkt angeschlossenen Peripheriegeräte aus.
• Schalten Sie das System mit dem Netzschalter aus.
• Trennen Sie das Gerät von der Stromquelle, indem Sie alle Netzkabel vom System bzw. aus der Steckdose ziehen.
• Ziehen Sie alle Kabel und alle an das System angeschlossenen
Telekommunikationsleitungen ab.
• Bewahren Sie alle Schrauben und anderen Befestigungselemente gut auf, nachdem
Sie die Gehäuseabdeckung entfernt haben. Wenn Sie Ihre Arbeiten im Systeminneren beendet haben, befestigen Sie die Gehäuseabdeckung mit den Originalschrauben bzw. -befestigungselementen.
• Führen Sie keine Arbeiten im Netzteil aus. Das Netzteil enthält keine für den
Benutzer wartungsbedürftigen Teile. Schicken Sie das Gerät für Wartungsarbeiten an den Hersteller zurück.
• Schalten Sie den Server aus, und ziehen Sie alle Netzkabel ab, bevor Sie
Komponenten ein- oder ausbauen, die nicht hot-plug-fähig sind.
• Wenn Sie ein hot-plug-fähiges Netzteil austauschen, ziehen Sie dessen Netzkabel ab, bevor Sie es aus dem Server ausbauen.
Caution: War Ihr Server in Betrieb, können die installierten Prozessoren und Kühlkörper heiß sein.
Sofern Sie keine Hot-Plug-Komponenten ein- oder ausbauen, warten Sie mit dem
Abnehmen der Abdeckungen, bis das System abgekühlt ist. Gehen Sie beim Aus- oder
Einbauen von Hot-Plug-Komponenten sorgfältig vor, um nicht mit heißen Komponenten in Berührung zu kommen.
Caution: Berühren Sie nicht die rotierenden Lüfterflügel, um Verletzungen zu vermeiden. Falls Ihr
System mit eine Lüfterabdeckung besitzt, darf es nicht ohne diese Abdeckung betrieben werden.
Warnhinweise für Racks
Das Geräte-Rack muß auf einer geeigneten, festen Unterlage verankert werden, um ein
Umkippen zu vermeiden, wenn ein Server oder andere Geräte herausgezogen werden.
Bei der Installation des Racks müssen die Anweisungen des Rack-Herstellers beachtet werden.
Gehen Sie bei der Installation von Geräten im Rack immer von unten nach oben vor, und bauen Sie das schwerste Gerät an der untersten Position im Rack ein.
Ziehen Sie jeweils immer nur ein Gerät aus dem Rack heraus.
Intel® Server System SR2500AL User’s Guide 173
Sie müssen für die gesamte Rack-Einheit einen Netztrennschalter einrichten. Dieser
Netztrennschalter muß leicht zugänglich sein und über eine Kennzeichnung verfügen, die besagt, daß er die Stromzufuhr zur gesamten Einheit steuert und nicht nur zu den Servern.
Zur Vermeidung von Stromschlaggefahr müssen das Rack selbst und alle darin eingebauten Geräte ordnungsgemäß geerdet sein.
Elektrostatische Entladungen (ESD)
Caution: Elektrostatische Entladungen können zur Beschädigung von Festplatten, Platinen und anderen Komponenten führen. Daher sollten Sie alle Arbeiten an einer ESD-Workstation ausführen. Steht ein solcher Arbeitsplatz nicht zur Verfügung, erzielen Sie einen gewissen
Schutz vor elektrostatischen Entladungen durch Tragen einer Antistatik-Manschette, die
Sie während der Arbeit zur Erdung an einem beliebigen unlackierten Metallteil des
Computergehäuses befestigen.
Gehen Sie bei der Handhabung von Platinen immer mit größter Vorsicht vor. Sie können
äußerst empfindlich gegenüber elektrostatischer Entladung sein. Halten Sie Platinen nur an den Kanten fest. Legen Sie die Platinen nach dem Auspacken aus der Schutzhülle oder nach dem Ausbau aus dem Server mit der Bauelementseite nach oben auf eine geerdete, statisch entladene Unterlage. Verwenden Sie dazu, sofern verfügbar, eine leitfähige
Schaumstoffunterlage, aber nicht die Schutzhülle der Platine. Ziehen Sie die Platine nicht
über eine Fläche.
Andere Gefahren
Batterieaustausch
Caution: Wird die Batterie unsachgemäß ausgetauscht, besteht Explosionsgefahr. Verwenden Sie als Ersatz nur die vom Gerätehersteller empfohlene Batterie.
Beachten Sie bei der Entsorgung von Batterien die gültigen Bestimmungen.
Versuchen Sie nicht, eine Batterie aufzuladen.
Versuchen Sie nicht, eine Batterie zu öffnen oder sonstwie zu beschädigen.
Kühlung und Luftstrom
Caution: Verlegen Sie Kabel sorgfältig entsprechend der Anleitung, um Störungen des Luftstroms und Kühlungsprobleme zu vermeiden.
Zur Gewährleistung des ordnungsgemäßen Kühlungs- und Luftstromverhaltens darf das
System nur mit angebrachten Gehäuseabdeckungen betrieben werden. Die
Inbetriebnahme des Systems ohne Abdeckung kann zur Beschädigung von
Systemkomponenten führen. So bringen Sie die Abdeckung wieder an:
• Vergewissern Sie sich zunächst, daß Sie keine Werkzeuge oder Teile im Gehäuse vergessen haben.
174 Intel® Server System SR2500AL User’s Guide
• Prüfen Sie, ob Kabel, Erweiterungskarten sowie weitere Komponenten ordnungsgemäß angebracht sind.
• Befestigen Sie die Abdeckungen am Gehäuse des Produkts, wie in dessen Anleitung beschrieben.
Laser-Peripheriegeräte oder -Komponenten
Caution: Beachten Sie zur Vermeidung von Strahlung und Verletzungen die folgenden Hinweise:
• Öffnen Sie keinesfalls das Gehäuse von Laser-Peripheriegeräten oder Laser-
Komponenten.
• Laser-Peripheriegeräte oder -Komponenten besitzen keine für den Benutzer wartungsbedürftigen Teile.
• Schicken Sie das Gerät für Wartungsarbeiten an den Hersteller zurück.
Français
Consignes de securite sur le serveur
Ce document s’applique aux cartes serveur Intel ® , au châssis de serveur Intel ® corporels, d’électrocution, d’incendie et de dommages matériels, lisez ce document et respectez tous les avertissements et précautions mentionnés dans ce guide avant d’installer ou de mettre à jour votre produit serveur Intel ® .
(sur pieds et sur rack) et aux périphériques installés. Pour réduire les risques de dommages
En cas de conflit entre les informations fournies dans ce document et celles livrées avec le produit ou publiées sur le site Web pour un produit particulier, la documentation du produit prime.
Votre serveur doit être intégré et entretenu uniquement par des techniciens qualifiés.
Vous devez suivre les informations de ce guide et les instructions d’assemblage des manuels de serveur pour vérifier et maintenir la conformité avec les certifications et approbations de produit existantes. Utilisez uniquement les composants décrits et réglementés spécifiés dans ce guide. L’utilisation d’autres produits/composants annulera la liste UL et les autres approbations réglementaires du produit, et le produit peut ne pas
être conforme aux autres lois et réglementations locales applicables au produit.
Séurité: avertissements et mises en garde
Pour éviter de vous blesser ou d’endommager votre équipement, lisez et respectez toutes les informations et consignes de sécurité avant de commencer l’installation du produit.
Les symboles de sécurité suivants peuvent être utilisés tout au long de cette documentation et peuvent figurer sur le produit ou sur son emballage.
Intel® Server System SR2500AL User’s Guide 175
ATTENTION
AVERTISSEMEN
T
Indique la présence d’un risque pouvant entraîner des blessures physiques mineures ou endommager légèrement le matériel si la mise en garde n’est pas prise en compte.
Indique la présence d’un risque pouvant entraîner des blessures corporelles graves si l’avertissement n’est pas pris en compte
.
Indique un risque potentiel si les informations signalées ne sont pas prises en compte.
Indique des risques d’électrocution pouvant entraîner des blessures corporelles graves ou mortelles si les consignes de sécurité ne sont pas respectées.
Signale des c omposants ou des surfaces soumis à des températures
élevées
.
Indique de ne pas toucher aux pales de ventilateur, car cela peut entraîner des blessures.
Indique de débrancher tous les cordons d’alimentation secteur pour déconnecter l’alimentation.
Veuillez réutiliser la batterie
Domaines d’utilisation prévus
Ce produit a été testé comme équipement informatique (ITE) et peut être installé dans des bureaux, des écoles, des salles informatiques et des endroits commerciaux similaires.
L’utilisation du présent produit dans des catégories et environnements de produits et domaines d’application (par exemple, le domaine médical, industriel, résidentiel, les systèmes d’alarme et les appareils de contrôle) autres qu’ITE doit faire l’objet d’évaluations supplémentaires.
Sélection d’un emplacement
Le système est conçu pour fonctionner dans un environnement standard de bureau.
Choisissez un emplacement respectant les conditions suivantes :
• Propre, sec et exempt de particules en suspension (autres que la poussière normale d’une pièce).
• Bien ventilé et à l’écart des sources de chaleur telles que la lumière directe du soleil et les radiateurs.
• À l’écart des sources de vibration ou des chocs physiques.
• Isolé des champs électromagnétiques importants produits par des appareils
électriques.
176 Intel® Server System SR2500AL User’s Guide
• Dans les régions sujettes aux orages magnétiques, nous vous recommandons de brancher votre système à un suppresseur de surtension et de déconnecter les lignes de télécommunication de votre modem pendant les orages.
• Équipé d’une prise murale reliée à la terre.
• Équipé d’un espace suffisant pour accéder aux cordons d’alimentation secteur, car ils servent de disjoncteur principal d’alimentation du produit.
Pratiques de manipulation de l’équipement
Réduisez le risque de dommages personnels ou matériels :
• Conformez-vous aux exigences de médecine du travail et de sécurité lorsque vous déplacez et soulevez le matériel.
• Utilisez l’assistance mécanique ou toute autre assistance appropriée lorsque vous déplacez et soulevez le matériel.
• Pour réduire le poids en vue de faciliter la manipulation, retirez tout composant amovible.
Alimentation et avertissements en matiére d’électricité
Attention: Le bouton d’alimentation, indiqué par le symbole de mise en veille, NE COUPE PAS complètement l’alimentation secteur du système car le courant de veille 5 V reste actif lorsque le système est sous tension. Pour couper l’alimentation du système, vous devez débrancher le cordon d’alimentation secteur de la prise murale. Votre système peut utiliser plusieurs cordons d’alimentation secteur. Assurez-vous que tous les cordons d’alimentation sont débranchés. Vous devez les débrancher avant d’ouvrir le châssis, d’ajouter ou de supprimer un composant non connectable à chaud.
Les alimentations de certains serveurs Intel sont munies de doubles fusibles pôle/neutre: veuillez observer les précautions d'usage afin d'éviter tout risque d'eléctrocution.
N’essayez pas de modifier ou d’utiliser un cordon d’alimentation secteur s’il ne s’agit pas du type exact requis. Un cordon secteur est requis pour chaque alimentation système.
Le bloc d’alimentation de ce produit ne contient aucun composant réparable par l’utilisateur. N’ouvrez pas le bloc d’alimentation. L’intérieur de celui-ci est soumis à des
Intel® Server System SR2500AL User’s Guide 177
niveaux dangereux de tension, de courant et d’énergie. Renvoyez-le au fabricant en cas de problème.
Lorsque vous remplacez un bloc d’alimentation à chaud, débranchez le cordon du bloc d’alimentation en cours de remplacement avant de le retirer du serveur.
Pour éviter tout risque d’électrocution, mettez le système hors tension et débranchez les cordons d’alimentation ainsi que les systèmes de télécommunication, réseaux et modems reliés au système avant d’ouvrir ce dernier.
Avertissements sur le cordon d’alimentation
Si aucun cordon d’alimentation secteur n’a été fourni avec votre produit, vous devez vous en procurer un qui soit approuvé pour une utilisation dans votre pays.
Attention: Pour éviter tout risque d’électrocution ou d’incendie, vérifiez les cordons d’alimentation qui seront utilisés avec le produit comme suit :
• N’essayez pas d’utiliser ou de modifier les cordons d’alimentation en CA s’ils ne correspondent pas exactement au type requis pour les prises électriques reliées à la terre.
• Les cordons d’alimentation doivent répondre aux critères suivants :
— Le cordon d’alimentation doit supporter une intensité supérieure à celle indiquée sur le produit.
— Le cordon d’alimentation doit posséder une broche ou un contact de mise à la terre approprié à la prise électrique.
• Les cordons d’alimentation électrique représentent le principal dispositif de déconnexion raccordé à l’alimentation secteur. Les prises de courant doivent se trouver à proximité de l’équipement et être facilement accessibles pour une déconnexion.
• Les cordons d’alimentation doivent être branchés sur des prises électriques correctement reliées à la terre.
Avertissements sur l’accés au systéme
178
Attention: Pour éviter de vous blesser ou d’endommager votre équipement, les consignes de sécurité suivantes s’appliquent chaque fois que vous accédez à l’intérieur du produit :
• Mettez hors tension tous les périphériques connectés à ce produit.
• Éteignez le système en appuyant sur le bouton d’alimentation.
• Déconnectez l’alimentation secteur en débranchant tous les cordons d’alimentation secteur du système ou de la prise murale.
• Déconnectez l’ensemble des câbles et lignes de télécommunication qui sont connectés au système.
Intel® Server System SR2500AL User’s Guide
• Mettez toutes les vis ou autres attaches de côté lorsque vous retirez les panneaux d’accès. Une fois que vous avez terminé d’accéder à l’intérieur du produit, refixez le panneau d’accès avec les vis ou attaches d’origine.
• N’essayez pas d’accéder à l’intérieur du bloc d’alimentation. Il ne contient aucune pièce réparable. Renvoyez-le au fabricant en cas de problème.
• Mettez le serveur hors tension et débranchez tous les cordons d’alimentation avant d’ajouter ou de remplacer tout composant non connectable à chaud.
• Lorsque vous remplacez le bloc d’alimentation à chaud, débranchez le cordon du bloc d’alimentation en cours de remplacement avant de retirer le bloc du serveur.
Attention: Si le serveur a été utilisé, les processeurs et dissipateurs de chaleur installés peuvent être chauds. À moins que vous n’ajoutiez ou ne retiriez un composant connectable à chaud, laissez le système refroidir avant d’ouvrir les panneaux. Pour éviter tout risque d’entrer en contact avec un composant chaud lors d’une installation à chaud, prenez toutes les précautions nécessaires lorsque vous retirez ou installez des composants connectables à chaud.
Attention: Pour éviter de vous blesser, ne touchez pas les pales de ventilateur en mouvement. Si votre système est fourni avec une protection sur le ventilateur, ne mettez pas le système en route sans la protection en place.
Avertissements sur le montage en rack
Le rack doit être fixé à un support inamovible pour éviter qu’il ne bascule lors de l’extension d’un serveur ou d’un élément de l’équipement. Le rack doit être installé conformément aux instructions du fabricant.
Installez les équipements dans le rack en partant du bas, en plaçant le plus lourd en bas du rack.
N’étendez qu’un seul élément de l’équipement à partir du rack à la fois.
Vous êtes responsable de l’installation d’un disjoncteur principal d’alimentation pour la totalité du rack. Ce disjoncteur principal doit être rapidement accessible et doit être
étiqueté comme contrôlant toute l’unité, et pas uniquement le ou les serveurs.
Pour éviter tout risque d’électrocution, le rack et chaque élément de l’équipement installé dans le rack doivent être correctement reliés à la terre.
Intel® Server System SR2500AL User’s Guide 179
Décharges électrostatiques (ESD)
Attention: Les décharges électrostatiques (ESD) peuvent endommager les lecteurs de disque dur, les cartes et d’autres pièces. Il est fortement conseillé d’effectuer l’ensemble des procédures décrites à un poste de travail protégé contre les ESD. Au cas où aucun poste de ce type ne serait disponible, protégez-vous contre les ESD en portant un bracelet antistatique relié à la masse du châssis (n’importe quelle surface métallique non peinte) de votre serveur lorsque que vous manipulez les pièces.
Manipulez toujours les cartes avec précaution. Elles peuvent être extrêmement sensibles aux ESD. Ne tenez les cartes que par leurs bords. Après avoir retiré une carte de son emballage de protection ou du serveur, placez-la sur une surface reliée à la terre, exempte de charge statique, composants orientés vers le haut. Utilisez si possible un tapis de mousse conducteur, mais pas l’emballage de la carte. Veillez à ce que la carte ne glisse sur aucune surface.
Autres risques
Remplacement de la pile
Attention: Il existe un risque d’explosion si la pile n’est pas correctement remplacée. Lors du remplacement de la pile, utilisez uniquement celle recommandée par le fabricant du matériel.
Mettez la pile au rebut en vous conformant aux réglementations locales.
N’essayez pas de recharger une pile.
N’essayez pas de démonter, de percer ou d’endommager la pile d’une quelconque façon.
Refroidissement et ventilation
180
Attention: Routez les câbles avec précaution comme indiqué pour minimiser les blocages de circulation d’air et les problèmes de refroidissement.
Afin de permettre une ventilation et un refroidissement corrects, ne mettez le système en marche que lorsque les panneaux du châssis sont en place. L’utilisation du système sans les panneaux peut endommager les composants système. Pour installer les panneaux :
• Vérifiez tout d’abord que vous n’avez pas oublié d’outils ou de composants détachés
à l’intérieur du système.
• Vérifiez que les câbles, les cartes d’extension et les autres composants sont correctement installés.
• Fixez les panneaux au châssis en suivant les instructions du produit.
Intel® Server System SR2500AL User’s Guide
Périphériques laser
Attention: Pour éviter tout risque d’exposition aux rayonnements et/ou de dommage personnel:
• N’ouvrez pas l’enceinte d’un périphérique laser.
• Les périphériques laser ne sont pas réparables par l’utilisateur.
• Retournez-les au fabricant en cas de problème.
Español
Información de seguridad del servidor
Este documento se aplica a las tarjetas de servidor de Intel®, las carcasas de servidor de
Intel® (montaje en bastidor y en pedestal) y los dispositivos periféricos. Para reducir el riesgo de daños corporales, descargas eléctricas, fuego y en el equipo, lea este documento y preste atención a todos las advertencias y precauciones de esta guía antes de instalar o mantener el producto de servidor de Intel®.
En el caso de que haya diferencias entre la información para un producto en particular contenida en este documento y la información proporcionada con dicho producto o en el sitio Web, la documentación del producto es la que prevalece.
Sólo personal técnico cualificado debe montar y prestar los servicios para el servidor.
Debe ceñirse a las directrices de esta guía y a las instrucciones de montaje de los manuales del servidor para asegurar y mantener el cumplimiento con las certificaciones y homologaciones existentes de los productos. Utilice sólo los componentes descritos y homologados que se especifican en esta guía. El uso de otros productos o componentes anulará la homologación UL y otras certificaciones oficiales del producto, pudiendo dejar de ser compatible con las normativas locales de los países en los que se comercializa.
Advertencias y precauciones sobre seguridad
Para reducir la posibilidad de que se produzcan lesiones personales o daños en la propiedad, antes de empezar a instalar el producto, lea, observe y cumpla toda la información e instrucciones de seguridad siguientes. Puede que se utilicen los siguientes símbolos de seguridad en la documentación y es posible que aparezcan en el producto o en su embalaje.
PRECAUCIÓN
ADVERTENCIA
Indica la existencia de un riesgo que podría causar lesiones personales o daños en la propiedad leves si no se tiene en cuenta la PRECAUCIÓN.
Indica la existencia de un riesgo que podría causar lesiones personales graves si no se tiene en cuenta la ADVERTENCIA.
Intel® Server System SR2500AL User’s Guide 181
Indica un riesgo potencial si no se tiene en cuenta la información indicada.
Indica riesgo de descargas eléctricas que podrían causar lesiones graves o la muerte si no se siguen las instrucciones de seguridad.
Indica componentes o superficies calientes.
Indica que no se deben tocar las aspas de los ventiladores, ya que de lo contrario se podrían producir lesiones.
Indica que es necesario desenchufar los cables de alimentación de CA para desconectar la alimentación de CA
Recicle por favor la batería
Aplicaciones y usos previstos
Este producto ha sido evaluado como equipo de tecnología informática (ITE) que puede instalarse en oficinas, escuelas, salas de equipos informáticos o lugares de ámbito comercial similares. Es posible que sea necesario llevar a cabo una evaluación adicional para comprobar si este producto es apropiado para otras categorías de productos y entornos además de las aplicaciones informáticas (por ejemplo, soluciones médicas, industriales, residenciales, sistemas de alarma y equipos de pruebas).
Seleccién de la ubicación
El sistema se ha diseñado para funcionar en un entorno normal de oficinas. Seleccione una ubicación que esté:
• Limpia, seca y libre de macropartículas en suspensión en el aire (que no sean el polvo habitual de la habitación).
• Bien ventilada y alejada de fuentes de calor, incluida la luz solar directa y los radiadores.
• Alejada de fuentes de vibración o de golpes físicos.
• Aislada de campos electromagnéticos producidos por dispositivos eléctricos.
• En zonas propensas a tormentas eléctricas, se recomienda que conecte el servidor a un supresor de sobretensiones y desconecte las líneas de telecomunicaciones al módem durante una tormenta eléctrica.
• Provista de una toma de corriente alterna correctamente conectada a tierra.
• Provista de espacio suficiente para acceder a los cables de la fuente de alimentación ya que constituyen la desconexión principal de la alimentación.
182 Intel® Server System SR2500AL User’s Guide
Manipulacién del equipo
Reduzca el riesgo de daños personales o en el equipo:
• Respete los requisitos de sanidad y seguridad laborales de su país cuando traslade y levante el equipo.
• Utilice medios mecánicos u otros que sean adecuados al trasladar o levantar el equipo.
• Para que el peso sea menor para manipularlo con más facilidad, extraiga los componentes que sean de fácil extracción.
Advertencias de alimentacién y eléctricas
Precaución: El botón de encendido, indicado con la marca del modo de reposo o stand-by, NO
DESCONECTA completamente la alimentación de CA del sistema, ya que el modo de reposo de 5 V sigue activo mientras el sistema está enchufado. Para desconectar el sistema debe desenchufar el cable de alimentación de CA de la toma de la pared. Puede usar más de un cable de alimentación de CA con el sistema. Asegúrese de que todos los cables de alimentación de CA están desenchufados. Asegúrese de que los cables de alimentación de CA estén desenchufado antes de abrir la carcasa, agregar o extraer cualquier componente que no es de conexión en funcionamiento.
Algunas fuentes de alimentación de electricidad de los servidores de Intel utilizan el polo neutral del fuselaje. Para evitar riesgos de choques electricos use precauciónes al trabajar con las fuentes de alimentación que utilizan el polo neutral de fuselaje.
No intente modificar ni utilizar un cable de alimentación de CA si no es del tipo exacto requerido. Se necesita un cable de CA para cada fuente de alimentación del sistema.
La fuente de alimentación de este producto no contiene piezas que puedan ser reparadas por el usuario. No abra la fuente de alimentación. Dentro de la fuente de alimentación puede haber niveles de tensión, corriente y energía peligrosos. Devuélvala al fabricante para repararla.
Al reemplazar una fuente de alimentación de conexión en funcionamiento, desenchufe el cable de alimentación de la fuente de alimentación que va a reemplazar antes de extraerla del servidor.
Para evitar el riesgo de descargas eléctricas, antes de abrir el servidor, apáguelo, desconecte el cable de alimentación, los sistemas de telecomunicaciones, las redes y los módems conectados al mismo.
Advertencias sobre el cable de alimentación
Si no se ha proporcionado con el producto ningún cable de alimentación de CA, adquiera alguno cuyo uso esté aprobado en su país.
Intel® Server System SR2500AL User’s Guide 183
Precaución: Para evitar descargas eléctricas o fuego, revise los cables de alimentación que usará con el producto tal y como se describe a continuación:
• No intente modificar ni utilizar los cables de alimentación de CA si no son exactamente del modelo especificado para ajustarse a las tomas de corriente conectadas a tierra.
• Los cables de alimentación deben reunir los siguientes requisitos:
— El cable de alimentación debe disponer de una capacidad nominal de corriente eléctrica mayor que la capacidad especificada en el producto.
— El cable de alimentación debe disponer de una patilla o contacto de conexión a tierra que sea apto para la toma de corriente.
• Los cables de la fuente de alimentación son los dispositivos de desconexión principales a la corriente alterna. El enchufe o enchufes de zócalo deben encontrarse cerca del equipo y el acceso a ellos debe poderse efectuar de forma inmediata con el fin de desconectarlos.
• Los cables de la fuente de alimentación deben estar conectados a los enchufes con una toma de tierra adecuada.
Advertencias el acceso al sistema
Precaución: Para evitar lesiones personales o daños en la propiedad, se aplican las siguientes instrucciones de seguridad siempre que se acceda al interior del producto:
• Apague todos los dispositivos periféricos conectados a este producto.
• Pulse el botón de alimentación para apagar el sistema.
• Desconecte la alimentación de CA desenchufando los cables de alimentación de CA del sistema o de la toma de corriente alterna.
• Desconecte todos los cables y líneas de telecomunicación que estén conectados al sistema.
• Guarde todos los tornillos o elementos de fijación cuando retire las cubiertas de acceso. Cuando termine de operar en el interior del producto, vuelva a colocar los tornillos o los elementos de fijación originales de la cubierta de acceso.
• No acceda al interior de la fuente de alimentación. No hay elementos en la fuente de alimentación que usted pueda reparar y utilizar. Devuélvala al fabricante para repararla.
• Apague el servidor y desconecte todos los cables de alimentación antes de agregar o reemplazar cualquier componente que no es de conexión en funcionamiento.
184 Intel® Server System SR2500AL User’s Guide
• Al reemplazar una fuente de alimentación de conexión en funcionamiento, desenchufe el cable de alimentación de la fuente de alimentación que va a reemplazar antes de extraerla del servidor.
Precaución: Si el servidor se ha estado ejecutando, los procesadores y disipadores de calor estarán recalentados. A no ser que esté instalando o extrayendo un componente de conexión en funcionamiento, deje que el sistema se enfríe antes de abrir las cubiertas. Para que no llegue a tocar los componentes que estén calientes cuando esté realizando una instalación de conexión en funcionamiento, tenga cuidado al extraer o instalar los componentes de conexión en funcionamiento.
Precaución: Para evitar posibles daños, no toque las aspas en movimiento de los ventiladores. Si el sistema se le ha suministrado con una protección para el ventilador, asegúrese de que cuando esté funcionando el sistema la protección esté en su sitio.
Advertencias sobre el montaje en bastidor
El bastidor del equipo se debe sujetar con un soporte fijo para evitar que se caiga cuando se extraiga un servidor o una pieza del mismo. El bastidor del equipo debe instalarse siguiendo las instrucciones del fabricante del bastidor.
Instale el equipo en el bastidor comenzando desde la parte de abajo, con el equipo más pesado en la parte inferior del bastidor.
Extraiga las piezas del equipo del bastidor de una a una.
El usuario es el responsable de la instalación de un dispositivo de desconexión de la alimentación principal para toda la unidad del bastidor. El acceso a este dispositivo de desconexión deberá ser de fácil acceso y deberán incluirse indicaciones que lo identifiquen como el control de alimentación eléctrica de toda la unidad, no sólo de los servidores.
Para evitar el riesgo de descargas eléctricas, deberá instalar una conexión a tierra apropiada para el bastidor y para cada pieza del equipo instalada en el mismo.
Descarga electrostática (ESD)
Precaución: Las descargas electrostáticas pueden dañar las unidades de disco, las tarjetas y otros componentes. Recomendamos que realice todos los procedimientos en una estación de trabajo protegida contra descargas electrostáticas. En caso de que no haya una
Intel® Server System SR2500AL User’s Guide 185
disponible, protéjase de alguna forma contras las descargas llevando un brazalete antiestático conectado a la toma de tierra de la carcasa (cualquier superficie de metal que no esté pintada) del servidor cuando manipule las piezas.
Manipule siempre las tarjetas con el máximo cuidado. Pueden ser sumamente sensibles a las descargas electrostáticas. Sujételas sólo por los bordes. Una vez extraída la tarjeta de su envoltorio de protección o del servidor, colóquela con el lado de los componentes hacia arriba sobre una superficie con toma de tierra y sin carga estática. Utilice una almohadilla de espuma conductora si dispone de ella, pero nunca el envoltorio de la tarjeta. No deslice la tarjeta sobre ninguna superficie.
Otros riesgos
Sustitución de la batería
Precaución: Existe el peligro de explosión si la batería no se reemplaza correctamente. Al reemplazar la batería, utilice sólo la batería recomendada por el fabricante del equipo.
Deseche las baterías respetando la normativa local.
No intente recargar la batería.
No intente desmontar, pinchar o causar cualquier otro desperfecto a una batería.
Enfriamiento y circulación de aire
Precaución: El tendido de los cables debe realizarse cuidadosamente tal y como se le indica para reducir al mínimo los problemas de obstrucción de la ventilación y de refrigeración.
Para conseguir una refrigeración y corriente de aire adecuadas, compruebe que cuando sistema esté funcionando, las cubiertas de la carcasa están instaladas. Si utiliza el sistema sin las cubiertas, podría dañar sus componentes. Para instalar las cubiertas:
• Compruebe primero que no ha dejado herramientas o piezas sueltas dentro del sistema.
• Compruebe que los cables, tarjetas adicionales y otros componentes están instalados correctamente.
• Sujete las cubiertas a la carcasa siguiendo las instrucciones del producto.
186 Intel® Server System SR2500AL User’s Guide
Periféricos o dispositivos láser
Precaución Para evitar el riesgo de la exposición a radiaciones o de daños personales:
• No abra la caja de ningún periférico o dispositivo láser
• Los periféricos o dispositivos láser no pueden ser reparados por el usuario
• Haga que el fabricante los repare
Intel® Server System SR2500AL User’s Guide 187
188 Intel® Server System SR2500AL User’s Guide
Download
Offentligt link opdateret
Det offentlige link til din chat er blevet opdateret. You may view and manage your chat links after registration here.
Dokument offentligt link
Annonce