idp Smart-30 Technical Manual

PDF

Document

2014-03-24

Color ID Card Printer

-Technical Manual

2014-03-24

Copyright Notice

Users must respect the copyright laws applicable in their country.

This manual must not be photocopied, translated, reproduced or transmitted in whole or in part for any reason and by the means that might be, albeit electronic or mechanical, without the express, written authorization of IDP Corporation.

All information contained herein may be subject to modification without prior notice.

IDP Corporation accepts no liability for any possible errors herein, nor for any accidental damage or damage caused through the dissemination or the use of this manual.

Trademarks

SMART is a trademark and IDP Card Printer is a registered trademark of IDP Corporation.

Windows is registered trademarks of Microsoft Corp. All other trademarks or registered trademarks are marks of their respective holders. Smart Design is a trademark of

IDP Corporation.

2014-03-24

1. Introduction



1.1 Printer Basic Information

◦ 1.1.1 Printer Outside Features

◦ 1.1.2 Printer Inside Features

◦ 1.1.3 Ribbon Cartridge Feature

◦ 1.1.4 LED Status and Button Operation

1.2 Printer Installation and Instructions

◦ 1.2.1 Ribbon Installation

◦ 1.2.2 Card Thickness Adjustment

◦ 1.2.3 Cards Load



1.3 Printer Specifications

2. Main Parts

2.1 Sensors

2.2 Thermal Head and Rollers

2.3 Motors

2.4 PCBs

2.5 Wired Diagram

2014-03-24



3. Parts Replacement

3.1 Covers

◦ 3.1.1 Side Cover Right / Left

◦ 3.1.2 LED-Button Unit

◦ 3.1.3 Stacker Unit

◦ 3.1.4 Front Cover

◦ 3.1.5 Rear Cover

3.2 Top Cover Unit

◦ 3.2.1 Thermal Print Head

◦ 3.2.2 Top Cover

◦ 3.2.3 Cooling Fan

◦ 3.2.4 Top Cover Frame

3.3 Main PCBs

◦ 3.3.1 Main Board

◦ 3.3.2 PCB Ribbon RF

2014-03-24



3.4 Drive Unit

◦ 3.4.1 Main Drive

◦ 3.4.2 Belt Tension Setting

◦ 3.4.3 Ribbon, Head Down_Up Drive



3.5 Rollers

◦ 3.5.1 Cleaning Roller / Cleaning Roller Fixed

4 Administration

4.1 Setup

◦ 4.1.1 Overview

 4.1.1.1 Function

 4.1.1.2 Start

◦ 4.1.2 Printer Setup

 4.1.2.1 Basic Setup

 4.1.2.2 Expansion Setup

◦ 4.1.3 Printer Setup Adjustment

 4.1.3.1 Printing Location

 4.1.3.2 Printing Density

 4.1.3.3 Ribbon Operation

 4.1.3.4 Flipper

2014-03-24



 4.1.3.5 Magnetic Stripe

 4.1.3.6 Thermal Print Head Replacement

 4.1.3.7 Security

 4.1.3.8 Etc.

4.2 Test

◦ 4.2.1 Overview

◦ 4.2.2 Basic Operation

 4.2.2.1 Select

 4.2.2.2 Control

 4.2.2.3 Print

 4.2.2.4 Allocation

 4.2.2.5 Status

 4.2.2.6 Message

◦ 4.2.3 Encoding

 4.2.3.1 Magnetic Stripe

 4.2.3.2 Contact SMART Card

 4.2.3.3 Contactless (PC/SC) SMART Card

2014-03-24



◦ 4.2.4 Status

 4.2.4.1 Printer Status Code

 4.2.4.2 Printer Error Code



4.3 Firmware

◦ 4.3.1 Overview

◦ 4.3.2 Automatic Update

◦ 4.3.3 Manual Update

5. Trouble Shooting

6.Appendix

A. Service Parts List

B. Expanded View

C. Option Unit Placement & Wiring

1.1 Printer Basic Information

1.1.1 Printer Outside Features

This SMART-30 Card Printer takes a power via the adaptor provided with the printer. Using USB port, it communicates with user’s PC. For the user’s convenience, the printer working status can be seen by LED and most of the operations can be controlled by buttons.

The following shows the external functional features found on your Smart Printer

No. Name Function

①

TOP COVER OPEN

BUTTON

Open Top Cover.

②

② HOPPER COVER

Load the cards for printing.

④

③ LED & BUTTON

Display printer status and control printer

③

④ SIDE COVER

⑤ STACKER Enable to remove Stacker

⑤

Fig.1-1 Printer Front/Side Features

2014-03-24

1.1 Printer Basic Information

⑥

⑦ ⑧ ⑩ ⑨

Fig.1-2 Printer Read Features

No. Name Function

⑥

REAR CARD

OUTLET

Eject Error Card

⑦ POWER SWITCH Printer On/Off

⑧

DC POWER

CONNECTOR

Connect DC power (Adapter)

⑨

⑩

USB PORT

ETHERNET PORT

(OPTION)

Communicate with PC using

USB cable

Use it after removing the ethernet port protector

2014-03-24

1.1 Printer Basic Information

1.1.2 Printer Inside Features

Smart Printer adopts a semi-permanent cartridge to install a Ribbon. The following shows the internal components and functional features found on your Smart Printer.

⑤

④

①

②

③

2014-03-24

Fig.1-3 Printer Inside Features

No.

①

②

Name

STACKER

HOPPER

Function

Stack printed cards and can be removed.

Load new cards for printing and encoding.

Loosen screws and adjust bracket according to card thickness.

③

CARD THICKNESS

CONTROL BRACKET

④ RIBBON CARTRIDGE Install ribbon and cleaning roller

⑤ THERMAL PRINT HEAD

This enables the Cards to be printed.

Caution! Do not contact the surface of the printer head with fingers or a sharp metal object to avoid degrading print quality or damaging printer head permanently.

1.1 Printer Basic Information

1.1.3 Ribbon Cartridge Feature

②

①

③

Fig.1-4 Ribbon Cartridge

④

No. Name Function

① Ribbon Cartridge

Install a Ribbon and a disposable cleaning roller provided with the

Ribbon. (Important! This semipermanent ribbon cartridge is a component of the printer. Printer does not operate if it is broken or damaged. In this case, please contact printer reseller.)

② Ribbon Take-Up Core Collect the ribbon used in printing

③ Ribbon Supply Core Provide the ribbon for printing

④

Disposable

Cleaning Roller

It removes dust in the surface of card to improve print quality before the card is printed. It should be changed together with the Ribbon.

(Caution! This disposable cleaning roller is provided with the Ribbon. If this is not changed, print quality mighty be degraded. )

2014-03-24

1.1 Printer Basic Information

1.1.4 LED Status and Button Operation

SMART-30 Printer shows the real-time working status to user using LED and can be controlled by button according to each working status.

LED

BUTTON

2014-03-24

1.1 Printer Basic Information

Please refer LED status and button operation. SMART-30 shows status messages on watchman that installed with printer driver.

Watchman

INIT Error xx

< Retry >

SMART - 30

System Ready

S m a r t

Unlock Please..

S m a r t

Verify your PC

S M A R T

Printing!

Print Error xx

< Cancel >

Top Cover Open

< Eject >

LED Button

RED

Blink

BLUE

Retry

Power

State

System Ready Status

Printer Locked Status

Need to Verify using

Authenticated PC.

In Printing

SMART-30 is ready. If you press button, power is turned on or off.

When activating Physical Key option and SMART-30 is locked by the key, or activating Root/User authentication option and SMART is locked by the password. Printer is locked so can’t be operated

When activating PC authentication option and using SMART-30 in other

PC. Printer can’t be operated

SMART-30 is in printing.

상세 설명

Error occur in initializing

Error code is displayed when SMART-30 can’t be initialized . Please press button to re-initialize.

RED

Blink

RED

Blink

Cancel

Error occur in printing or

Moving card

Error occur in printing or moving card. If pressing button,, printing will be canceled.

Moving

Card

Top Cover Open Top cover is opened. If pressing button, SMART-30 eject card.

2014-03-24

1.1 Printer Basic Information

No Watchman

Check Please..

Ribbon Not Found

Check Please..

Ribbon Zero

Check Please..

TPH Not Found

Card Out Error

< Cancel >

Board Test Mode

Wait

LED

RED

Blink

RED

Blink

RED

Blink

RED

Blink

Initializing

RED

Blink

Button

Ribbon

Research

Ribbon

Research

State

Thermal Print Head is not installed

Card Out Error

(Check card in Printer)

Ribbon remains is zero. Need to change the ribbon. If pressing button, SMART-

30 search ribbon again.

When the thermal Print Heat is not installed or disconnected to head cable, this message is displayed. Please power off SMART printer and check the thermal head installation status.

상세 설명

Ribbon is not installed or not searched

Fail to ribbon search. Check the ribbon installed status and if there is nor ribbon, please reinstall ribbon in printer.

All ribbons are used

Printer Test Mode

When there is printing error , the card is not ejected after pressing button.

SMART-30 is on test mode that the sensors and motors of printer are tested.

2014-03-24

1.1 Printer Basic Information

Printer Error Code

Error Code

Details

Card In Error

Card Move Center Error

Card Out Error

Card Move Magnetic Error

Card Move IC Contact Error

Card Move RF Error

Card Move Error from Printer to Flipper

Card Move Error from Flipper to Printer

Thermal Print Head Up Error

Thermal Print Head Down Error

IC Contactor Up Error

IC Contactor Down Error

Flipper Top Error

Flipper Bottom Error

Error in Printing

Magnetic R/W Error

Error Code

Details

Ribbon Search Error

Ribbon Move Error

No Thermal Print Head Installed

Thermal Print Head Overheat

No Ribbon Installed

Printing Data Error

Card Back Out Error

Magnetic Data Removing Error

Wrong Printer Password

Magnetic Track 1 Read Error

Magnetic Track 2 Read Error

Magnetic Track 3 Read Error

Printer Lock State

Printer Spool Full

Undefined

2014-03-24

1.2 Printer Installation and Instructions

1.2 Printer Installations and Instructions

1.2.1 Ribbon Installation

Before printing, prepare the related items such as a card, a ribbon and a cleaning roller. In this section, we invite you to know the proper method to install the ribbon and the cleaning roller into the printer.

1. Turn off the power of printer

2. Open the top cover of printer by pressing the top cover open button

(Refer to Fig.2-1).

3. Take out the ribbon cartridge (Refer to

Fig.2-2).

Fig.2-1 Open Top Cover Fig.2-2 Take out ribbon cartridge

2014-03-24

Ribbon Supply

Core

Ribbon Take-up

Core

Fig.2-3 Prepare the ribbon

4. Prepare the ribbon before inserting it into the ribbon cartridge.

※ Refer to the illustration on the inside of the cartridge.

2014-03-24

1.2 Printer Installation and Instructions

Fig.2-4 Install the ribbon]

5. Insert the supply side of the ribbon to no.1 hole and press the opposite(no.2) until it clicks. Insert the take-up side of the ribbon to no.3 and no.4 by the same way. And fasten the ribbon.

※ Caution! If the ribbon is not fastened, a rolling up error might happen.

1.2 Printer Installation and Instructions

Fig.2-5 Install the cleaning roller

6. Install the disposable cleaning roller to the ribbon cartridge.

2014-03-24

Fig.2-6 Peel the protective wrapper

7. Peel the protective wrapper from the cleaning roller.

To avoid contamination, always hold the cleaning roller. Be careful to touching, dust and contamination because it is adhesive.

※ Caution! Do not use without peeling off the not perform its function.

1.2 Printer Installation and Instructions

Fig.2-7 Install the ribbon cartridge

8. Install the ribbon cartridge to the printer after install the ribbon and cleaning roller to the cartridge.

Fig.2-8 Close Top Cover

9. Close the top cover until it clicks.

(If it is not closed, check the installation state of the ribbon cartridge.)

2014-03-24

1.2 Printer Installation and Instructions

1.2.2 Card Thickness Adjustment

This session shows how to adjust the card thickness for taking a card into printer properly.

Card Thickness Adjustment

(HOPPER GATE)

Fig.2-10 Card Thickness Adjustment 2

3. For Adjusting card thickness, please loosen two screws with a phillips screwdriver, and push up or down the HOPPER GATE, and tighten the crews(Fiz.2-10).

(Card Thickness 0.76mm is default)

3. For 0.76mm(30mil) cards, please push up the HOPPER GATE and tighten the screws(Fig.2-11)

4. For 0.38mm(15mil) cards, please push down the HOPPER GATE and tighten the screws(Fig.2-12)

Fig.2-9 Card Thickness Adjustment 1

1. If the hopper cover is closed, please open it.

2. Please check the Hopper Gate is properly adjusted to your card’s thickness.

(Caution! If the adjusted card thickness is thinner than your card’s thickness, SMART-30 can’ take a card into printer. If the adjusted card thickness is thicker than your card’s thickness, several cards may be taken into printer at the same time and error occur.)

Fig.2-11 For 0.76mm Cards Fig.2-12 For 0.38mm Cards

2014-03-24

1.2 Printer Installation and Instructions

1.2.3 Cards Load

This section shows how to load plastic cards into the Smart Printer.

1. Properly hold cards by sides (Fiz.2-13).

※ Caution! Do not bend the cards and do not touch the surface of the cards.

Fig.2-13 Prepare Card 1

2. Push the stack back and forth to an angle of about 45 ° vertically.

※ Caution! Static charge makes cards stuck with significant adhesive force. These cards must be physically separated from each other before inserted into the feeder.

If not separated, feeding or printing problems may occur.

Fig.2-14 Prepare cards 2 Fig.2-15 Prepare Cards 3

2014-03-24

Fig.2-16 Cards Load 1 Fig.2-17 Card Load 2

1.2 Printer Installation and Instructions

3. Restore the cards stack to its original condition.

4. Place the cards to the hopper and close the hopper cover.

5. In case of one card insert, refer to Fig.2-

18 and Fig.2-19, and insert the card into the hopper.

(Please push a card until you can’t push it any more.)

Fig.2-18 Cards Load 3 Fig.2-19 Cards Load 4

2014-03-24

1.3 Printer Specifications

2014-03-24

Product Specification

Card Types

Printing Method

Card Format

Card Thickness

Resolution

Memory

Printing Speed

Ribbon Capacity

Hopper & Stacker

Interface

Display

Power

Dimension

Operating Environment

Weight

Agency Listing

Printer Driver

Option

M/S Encoding Moudule

IC(Contact)Encoding Module

RF Encoding(Internal)

Flipper

1.3 Printer Specifications

SMART-30S SMART-30D

PVC, Polyester Cards with polished PVC finish

Dye-Sublimation / Resin Thermal / Edge-to-Edge

ISO CR80 (54mm x 86mm)

0.38mm(15mil) ~ 0.76mm(30mil)

300 dpi

32MB

Color (YMCKO ) : 128 card/hour

Color (YMCKOK) : 100 card/hour

Black Overlay (KO) : 300 cards/hour

Mono (Black) : 600 cards/hour

Color (YMCKO) : 250 cards/roll

Color (YMCKOK) : 200 cards/roll

Black Overlay (KO) : 600 cards/roll

Mono : 1200 cards/roll (Black, Gold, Silver)

Hopper : 100 cards, Stacker : 25 cards

USB

1 LED Button

Free Voltage (110/240V AC), 50~60 HZ, 45W

172mm(W) x 190mm(H) x 377mm(D)

Temperature : 20~35 ℃, Humidity : 20~80%

3.4 Kg

MIC, CE, FCC

Microsoft Windows 2000/2003/XP/Vista/7/8, Mac OS, Linux

ISO 7811 (Track I,II,III Read / Write) Hico/LoCo

ISO 7816 (ID - 1)

ISO 14443 (Type A / B), ISO 15693, MIFARE

Option Default

2.1 Sensors

CASE OPEN

SENSOR

ENCODER

SENSOR

2014-03-24

CARD IN

SENSOR

COLOR OUT

SENSOR

HEAD UP-DOWN

SENSOR

COLOR IN

SENSOR

2.1 Sensors

CARD OUT

SENSOR

2.2 Thermal Head and Rollers

Cleaning

Roller

Card Supply

Roller

MS Roller

Thermal

Head

2.2 Thermal Head and Rollers

Card In

Roller

Cleaning Roller

Fixed

Printing

Roller

IC Roller

2014-03-24

2.3 Motors

Ribbon Driver

Motor(DC)

FAN

2.3 Motors

Main Driver

Step Motor

Head Up_Down-

Hopper Motor(DC)

2014-03-24

2.4 PCBs

Front

Display

2014-03-24

Ribbon

PCB

Main

2.4 PCBs

2.5 Wired Diagram

2014-03-24

2.5 Wired Diagram

3.1 Covers

3.1.1 Side Cover Right / Left

Screw

3.1 Covers

1. Loosen 4 screws on Bottom Frame.

2. Open Front Cover and Top Cover.

3. Grip the bottom part of right/left Side

Cover and pivot from upper part of right/left Side Cover.

4. Upper part of right/left Side Cover is connected with Side Plate, so push up the

Side cover paralleled to Side Plate direction to disassemble.

2014-03-24

Right

Cover

3.1.2 LED-Button Unit

Front

Cover

3.1 Covers

Button

Power wire

1. Open the Front Cover.

2. Broaden the gab between LED-Button unit and Main Frame using screw driver, and then Hook is disassembled. At this time, pull carefully the LED-Button unit to disassemble it.

3. When pull out LED-Button unit, be cautious not to make damage on the wire of LED-

Button unit.

4. Disconnect LED-Button Power wire from

LED-Button unit.

LED-Button

Unit

2014-03-24

3.1.3 Stacker Unit

STACKER

3.1 Covers

1. Hold both sides of the Stacker.

2. Pull out Stacker to separate it from printer.

At this time, hold printer to prevent printer from moving.

3. When install Stacker into printer, push it according the rail of the Stacker and the track of printer.

4. Push the Stacker into printer until the clicking sound.

2014-03-24

3.1.4 Front Cover

Front

Cover

3.1 Covers

1. Open the Front Cover

2. Broaden the gab between Main Frame and

Front Cover using screw driver and disassemble Front Cover from Main Frame.

Front

Cover

2014-03-24

3.1.5 Rear Cover

Left View

Rear Cover

3.1 Covers

1. Rear Cover is assembled to Main Frame by

Hook.

2. Unlocked the Hook on both side of the

Rear Cover using Screw Driver.

Right View

2014-03-24

3.2 Top Cover Unit

3.2.1 Thermal Print Head

Top Cover

Unit

Thermal

Head

Top Cover

Frame

Thermal

Head

Thermal

Head wire

2014-03-24

3.2 Top Cover Unit

1. Printer Top Cover Unit consists of Top

Cover, Top Cover Frame and Thermal Print

Head.

2. Thermal Print Head is fixed by Hinge and

Hook on Top Cover Frame.

3. Press the push button of Hook, rotate the thermal print head to the bottom side and disassemble thermal print head from Top

Cover Frame.

4. Disconnect the Thermal Print Head Wire.

3.2.2 Top Cover

Screw

3.2 Top Cover Unit

1. Top Cover is fixed to Top Cover Frame by 3 screws and 2 Hooks.

2. Loosen Screws and unlock Hooks using screw driver, and then disassemble Top

Cover from Top Cover Frame.

Screw

2014-03-24

3.2.3 Cooling Fan

Cooling FAN

Hook

FAN wire

Connector

3.2 Top Cover Unit

1. Cooling Fan is fixed on Top Cover Frame by 2 Hooks.

2. Unlock Hooks using screw drive and disassemble Cooling Fan.

3. Fan Wire is connected to Connector of

Main Board through inside of Printer.

4. Disassemble Bottom Frame from Printer and disconnect Fan Wire from Connector.

5. Arrange Fan Wire and disconnect. Be cautious not to peel it by Plate edge.

M / B

2014-03-24

3.2 Top Cover Unit

3.2.4 Top Cover Frame

Screw

Shaft Top

Set

Color

Sensor wire

Top Cover

Mold

M / B

Thermal

Head wire

Color

Sensor wire

2014-03-24

1. Top Cover Frame is assembled to Main

Frame by Shaft Top Set.

2. Disconnect Thermal Print Head Wire on

Main Board.

3. Disconnect Color In Sensor Wire on

Thermal Print Head position.

4. Loosen 2 screws and broaden both Main

Frames, and then disassemble Top Cover

Frame.

5. To disassemble Color in Sensor, push

Snap for fixing and pull out Color In

Sensor.

3.3 Main PCBs

3.3.1 Main Board

Hook

Push

2014-03-24

Main

Frame

3.3 Main PCBs

1. Main Board is fixed on Bottom Frame.

2. Bottom Frame is fixed on Main Frame by

4 Hooks and 4 Screws, but 4 screws are loosened when Side Cover was disassembled. (Refer to 3.1.1).

3. 2 Hooks are at same position on each side (Lift and Right) on Bottom Frame.

4. To unlock Hooke, push Main Frame to the right and push Bottom Frame to the left.

5. More easy way to unlock Hooks, hold

Main Frame and push Bottom Frame to the back side.

6. Main Board is fixed on Main Frame by 6

Screws.

Screw

Base Plate M / B

Left View

3.3 Main PCBs

1. Before disassembling Main Board, disconnect cables(T2, T3, T4, T5) on the

Right side.

( Be cautious not to make damage on T4

FFC)

2. T5 Wire is connected to LCD-Button unit.

On 3.1.2, when disassembling LCD-

Button unit, T5 was disconnected form

LCD-Button unit, but disconnect T5 Wire to disassemble Main Board.

3. Disconnect cables(T1, T6) on the Left side.

Right View

2014-03-24

T5 T4 T2 T3

3.3.2 PCB Ribbon RF

2014-03-24

FFC wire

Pull

PCB

Ribbon RF

3.3 Main PCBs

1. PCB Ribbon RF is fixed by Hook.

2. Disconnect FFC Wire from PCB Ribbon RF

(Be cautious no to make damage on FFC connector)

3. Lift Hook parts by using the screw driver or other device and pull out paralleled to

Side Frame direction to disassemble.

3.4 Drive Unit

3.4.1 Main Drive

3.4 Drive Unit

Main Drive

Motor

1. Main Drive consists of Step Motor and Time

Belt.

2. Disassemble Pulley(2), Time Belt(3) and

GEAR(7), and then can loosen 3 screws for fixing Step Motor.

3. Step Motor is located inside of Frame.

4. When assemble Step Motor, adjusting the tension by assembling Pulley(2) and Time

Belt(3) together and tighten 3 screws.

2014-03-24

3.4.2 BELT Tension Setting

3.3 Drive Unit

Belt-Step Motor 50M2M160 Tension

Setting

- After put the belt to the pulley, press the pulley as 1.5 ~ 2 kgf to the No.1 arrow direction as Fig.3-1.

- In this state, tighten 3 screws to set tension and fix Step Motor.

Fig,3-1

2014-03-24

3.4.3 Ribbon, Head Down_Up Drive

3.4 Drive Unit

1. Ribbon and Head Down_Up Drive is located on the left side of Frame.

2 Ribbon Motor is fixed by 2 screws inside of

Frame. (See B.2.1 ASSY S3,LEFT-1, B2.2 ASSY

S3,LEFT-2)

3 After disassembling Gear is assembled to

Ribbon Motor, enable to disassemble Ribbon

Motor.

4 Head Up/Down Motor is fixed by 3 screws inside of Frame. (See B.2.1 ASSY S3,LEFT-1,

B2.2 ASSY S3,LEFT-2)

5 After disassembling Gear(25) and ASSY(24), enable to disassemble Head Up/Down Motor.

6 After loosening 3 screws and disconnecting wire, enable to disassemble Head Up/Down

Motor.

Head

Up/Down

Motor

2014-03-24

3.5 Rollers

2014-03-24

Cleaning

Roller Fixed

Card In

Roller2

Card In

Roller1

Ms Roller

Printing

Roller

3.6 Rollers

1. Every Roller is fixed by using Bearing or

Bushing on each Main Frame.

2. Disassemble E-Ring on the end of Roller.

3. Disassemble Bearing or Bushing fixed on

Frame. While pushing Roller to Frame

Right Side. Disassemble Left Side of

Roller from Frame.

IC Roller

3.6 Rollers

3.5.1 Cleaning Roller / Cleaning Roller Fixed

Cleaning

Roller

Cleaning

Roller BKT

1. While broadening the fixing parts of

Cleaning Roller Bracket, pull out Cleaning

Roller.

2. Cleaning Roller Bracket is assembled to

Main Frame by using Hinge.

3. Transform the fixing parts of Main Frame for Hinge and disassemble Cleaning

Bracket.

4. Disassemble Bush on the end of Cleaning

Roller Fixed.

5. While pushing Cleaning Roller Fixed to the Right Side, disassemble Roller from the Left Side.

Cleaning

Roller Fixed

Main Frame

2014-03-24

4.1 Setup

4.1.1 Overview

4.1.1.1 Function

SMART Card Printer is delivered in optimized state from factory. However it can be set the setup value using

CardPrinterSetup Utility provided with CD when the unit is disassemble and reassemble or change of part. The following setup value can be changed using CardPrinterSetup utility.

Item Explanation

Print Location

Print Thickness

Ribbon Operation

Set the start position or end position of the printed image.

Set the print thickness of color, resin black, overlay.

Set the ribbon moving power

Flipper

Magnetic Stripe

Ribbon Color Sensor

Recognition

Security

Etc.

Set the rotation angle of Flipper

Set the start position of magnetic data.

Set the sensor value to distinguish the ribbon color.

Set the value for the printer security

Set the printer’s hardware version and the printer state.

2014-03-24

4.1 Setup

4.1.1.2 Start

When start the program there will be displayed the password input window. If input the password, the recorded setup value will be shown and can change that value. The password is saved to SMART Card Printer so even if change to other PC, it need to input the password to change the setup value.

(SMART Printer is not set its password so if you press O.K, you can see the setup value and can change. Default is no password)

2014-03-24

[ CardPrinterSetup startup ] [ CardPrinterSetup main window ]

4.1 Setup

4.1.2 Setup

4.1.2.1 Basic Setup

The most of basic setup can be realized on this window easily. To set more detailed setup, press “>” button for expansion.

Printer ID | Printer Name

Change Root/User password for SMART Printer

Device selection tab

Printer information ( Firmware Version, Serial Number)

Thermal header information

Image position related factors

Image density related factors

Expansion button for extended setup

Calibration sheet preview and printing

Main menus for get/set, save/load, close and load default

2014-03-24

4.1 Setup

•

Basic Setup Item

Item

Device

Change Password Change password

Firmware Ver. The printer’s firmware version

Serial No.

Header Serial No.

Header Resister

The printer’s serial no.

The printer’s Thermal Print Head serial no. When the thermal print head is change, it should be changed.(See 4.1.3.6)

The resistor value of the thermal print head. When the thermal print head is change, it should be changed.

Head Type

Explanation

Available device list will be displayed. “SMART” is printer ID value. “I&A SMART Card Printer” is the printer driver name. Using the printer ID, the printer can be distinguish when you use SDK.

X Start Position

Y Start Position

Y End Position

Y Scale

Set type of thermal print head.

Adjust X start position (Range : -30 ~ 30)

※ If the value is change, the example will be changed. (See 4.1.3.1)

Adjust Y start position. (Range : -30 ~ 30)

※ If the value is change, the example will be changed. (See 4.1.3.1)

Adjust Y end position (Range : -20 ~ 20)

※ If the value is change, the example will be changed. (See 4.1.3.1)

Adjust the length of image (Range : -60 ~ 60)

※ If the value is change, the example will be changed. (See 4.1.3.1)

Total Density Set the image’s total density (Range : -500 ~ 500) (See 4.1.3.2)

YMC Density Set the color density (YMC) (Range : -500 ~ 500) (See 4.1.3.2)

2014-03-24

•

Basic Setup Item

Item

Black Density

Explanation

Set the image’s total density (Range : -1500 ~ 1000) (See 4.1.3.2)

Overlay Density Set the color density (YMC) (Range : -500 ~ 500) (See 4.1.3.2)

Example

Get Config.

Preview the changed value

To check the adjusted value. You can print the test card

Show the expansion items

Set Config.

Load from File

Save to File

Load : SMART

Load : SMART Lite

Load the printer’s setup value

Save the changed setup value

In case you use the password, if it is not matching, it will not be saved

Load the saved file

Save the setup value to the file

Exit the program

Load standard setup value for SMART

Load standard setup value for SMART Lite

Load : SMART Rewritable Load standard setup value for SMART Rewritable

4.1 Setup

2014-03-24

4.1 Setup

4.1.2.2 Expansion Setup

This window can be used to check the printer’s state or change the detailed setup.

Menu buttons

Usage counter

Ribbon sensor control factors

Ribbon motor control factors

Flipper control factors

Magnetic control factors

Security factors

2014-03-24

4.1 Setup

•

Expansion Setup Item

I s

Item

Change Printer ID

Explanation

When use SDK, this ID can be used to distinguish each printer (See 4.1.3.8)

Set PC Serial

Change Head

When use PC Authentication, set the PC to print (See 4.1.3.7)

In case of changing thermal print head, set the serial no. and resistor value (See 4.1.3.6)

Set Mag. Encrypt Key When transport the magnetic data and if it is encrypted, you can set the Key (See 4.1.3.7)

Image

Magnetic

SIM

External RF

Total printed image number

Total magnetic encoding number

Total Contact Smartcard encoding number (It can be increasing by SDK)

Total Contact Smartcard(SIM) encoding number (It can be increased by SDK)

Total RF Smartcard(external) encoding number (It can be increased by SDK)

Internal RF

Printed Panels

Total RF Smartcard(internal) encoding number (It can be increased by SDK)

Printed panel number for the image printing

Cleaning Count Total printed panel number and magnetic encoding number for checking cleaning cycle.

Skipped Cleaning After demanding clean warning, skipped cleaning number

Image After installing new head, printed image number

Magnetic

SIM

After installing new head, magnetic encoding number

After installing new head, Contact Smartcard encoding number (It can be increasing by SDK)

After installing new head, SIM Smartcard encoding number (It can be increased by SDK) s e

External RF

Internal RF

After installing new head, RF card(external) encoding number (It can be increased by SDK)

After installing new head, RF card(internal) encoding number (It can be increased by SDK)

Cleaning Count

After installing new head, printed panel number and magnetic encoding number for checking cleaning cycle.

2014-03-24

Skipped Cleaning After installing new head and demanding clean warning, skipped cleaning number

4.1 Setup

•

Expansion Setup Item

Item

Yellow Level

Magenta Level

Cyan Level

Black Level

RMP +

RMP -

RMM+

RMM-

Auto Rotator Set

Rotate Top

Rotate Bottom

Reserved

Warming Up Display

Mag. Write Mode

Magnetic Space

2014-03-24

SBS Only

Explanation

Set the yellow level value (Use only in board type 1, 2 )

Set the magnetic level value (Use only in board type 1, 2)

Set the cyan level value (Use board type 1, 2)

Set the black level value (Use board type 1, 2)

Set the ribbon motor’s max torque value when a panel of ribbon is being printed on a card

Range : 2000 ~ 7000 (See 4.1.3.3)

Set the ribbon motor’s min torque value when a panel of ribbon is being printed on a card

Range : 2000 ~ 7000 (See 4.1.3.3)

Set the ribbon motor’s max torque value when a panel of ribbon is not being printed (RMM+ should be bigger than RMM–) Range : 4000 ~ 8000 (See 4.1.3.3)

Set the ribbon motor’s min torque value when a panel of ribbon is not being printed (RMM– should be smaller than RMM+) Range : 4000 ~ 8000 (See 4.1.3.3)

Automatically Find proper Rotate Top and Rotator Bottom value

Set the angle to be flat for the Flipper front side (Range : -30 ~ 30)

(The lower the value the more the angle) (See 4.1.3.4)

Set the angle to be flat for the Flipper back side (Range : -30 ~ 30)

(The lower the value the more the angle) (See 4.1.3.4)

Not Use

Set the cycle of blinking LED button when heat the head on RW model. If the value is increased, the LED blink slower.

Set the track writing mode

Set the start position of magnetic data (Range : 10 ~ 30)

If the value is increased, the start position will be close to the end (See 4.1.3.5)

Set the printer is only operated in the application which made by SDK (See 4.1.3.7)

•

Expansion Setup Item

Item

Board type

Security

Use USB Serial

Ribbon Position

Card Out Delay

Card Out

Explanation

Set the main board type (Do not change!)

Authentication function is applied for security in SMART printer. (See 4.1.3.7)

- PC Auth. : Matching SMART printer and PC ( To use this function, press “ Set PC Serial” and save the

PC authentication information to SMART Printer)

- Physical key : Set the use of Physical Key in case the printer have customized physical key

- User Auth. : Set password for specified user.

- Root Auth. : Set password for administrator.

When SMART is connected to USB, it transmits the USB serial number to PC. Default is the same number used by all SMART. Please set this option when you want to use multiple

SMART printers connected to 1 PC via USB. It enables unique serial numbers for each USB.

(See 4.1.3.8)

When you want to use multiple SMART printers connected to 1 PC via USB, you have to set this option of SMART one at a time and connect all SMARTs to PC via USB.

Option for ribbon printing reposition. It can be adjusted between +5 ~ -5 (mm).

Set the time to operate Hopper Motor. Do not change.

Set printed or encoded card out direction (The back out can be done only in dual side printer)

Error Card Out

DCL Mode

Dump Mode

Cleaning Warning

2014-03-24

Set error card out direction (The back out can be done only in dual side printer)

Use DCL mode. If set DCL mode, the driver installation will not be required when connect the printer. Even if the driver is installed, it does not use the driver. Please note it is developed for the user who want to operate the printer with their specific program because do not need to use the driver. (Note: When use this function, it is not printing in normal program.)

(See 4.1.3.8)

Set to record the log data in printer.

Set to activate cleaning warning window. (See 4.1.3.8)

4.1.3 Printer Setup Adjustment

4.1.3.1 Printing Location

SMART Card Printer is the direct thermal printer and need to some setting to print all over the card surface.

In CardPrinterSetup, if press “Print” button, the image like left side will be printed. In this time, if four circles on each side are printed well and the space of upper & bottom is in 0.5mm, it is proper setting.

For correct setting, you can adjust the setup value as follows.

1. Do not make too much space on left and right side as adjusting X start position value.

2. Do make the image start point in 0.4mm ~ 0.5mm from the card upper side as adjusting Y start position value.

3. Do make the image end point in 0.4mm ~ 0.5mm from the card bottom side as adjusting Y end position value. In this case, Y scale value should be input more bigger than the proper setup value.

4. Do make the four circles can be shown fully as adjusting Y scale value.

2014-03-24

4.1 Setup

4.1.3.2 Printing Density

SMART Card Printer is direct thermal printer. Use the thermal heat to print. To print the correct and proper printing, the thermal heat should be different in color printing, resin black printing, overlay printing. So for the best printing image, some adjustment is needed.

•

Color Printing Density

Color printing is print the color image using the color ribbon. SMART printer can print 16,777,216 color. In its color printing thickness, the color expression range can be widen and get the clear image by printing so thickly as possible as the ribbon is allowed. However if it is too thick, the ribbon can folded and there might be green or red bad image. And if it is too weak, the image is not clear as below third figure. Set the proper thickness.

2014-03-24

Too Strong Proper Too Weak

4.1 Setup

•

Resin Black Printing Density

Resin Black is used to print the black clearly such as the barcode or text. It print the black which extracted by the printer device driver or set as black in Smart Design. The red box in the below figure is printed by resin black.

Resin Black is printed as binary type, not level for the printing result. So the setting standard of printing thickness is different.

If the thickness is too strong, the barcode is not clear and too widen. And if too weak, the barcode is printed too short. Set the resin black printing thickness properly to get the clear barcode printing. Not too strong but a little bit strong is best.

2014-03-24

Too Strong Proper Too Weak

4.1 Setup

•

Overlay Printing Thickness

Overlay is coating to the surface of card for the protection of printing image. Usually the overlay print all over the card surface but it can be printed in specific area by the device driver or Smart Design software.

Overlay is binary type such as black resin, print or not. So the setting standard of printing thickness is different.

If it is too strong, it is too dull and can be occurred the bad overly such as left figure. And if too weak, some area will not be overlaid. You can check it if place the card under light. So set the overlay printing thickness properly. Not too strong but a little bit strong is best.

2014-03-24

Too Strong Proper Too Weak

4.1 Setup

4.1.3.3 Ribbon Operation

SMART-30 Card Printer’s ribbon movement is variable to make the interference minimized. So to get the stable image quality, set the proper ribbon movement setting. As below graph SMART Card Printer is control the speed of printing and normal movement differently to get the regular speed. And its movement speed is changed for the remained ribbon balance. Set the movement speed as below graph.

RMP control the ribbon movement when printing. If set too low, the ribbon can not be rewind and the problem can be occurred. On the contrary if set too strong, the rolling speed is too fast so there might be bad image.

RMM control the normal movement. If set too low value, the printer is stop as print head is adhered with ribbon. If too high, the ribbon rolling speed is too fast so the correct printing position can not be detected.

(We recommend to not change RMP and RMM until there is critical problem)

Movement Speed

RMM +

RMM -

RMP +

RMP -

Normal Ribbon Movement

Printing Ribbon Movement

250 1 Ribbon Balance

2014-03-24

4.1 Setup

4.1.3.4 Flipper

On SMART-30, flipper can be attached as option. When there is no printing, the Flipper keep the horizontal flat. So the setup of Flipper is to make it the horizontal flat by adjusting its angle.

“Rotate Top” and “Rotate Bottom” are the accurate setting when the Flipper is front side or back side to make a horizontal flat with the card movement passage. This value is between -30 ~ 30 and + is upper adjustment, - is down adjustment.

(We recommend that there is Flipper card jam problem.)

2014-03-24

4.1 Setup

4.1.3.5 Magnetic Stripe

On SMART-30, Magnetic Stripe Encoder can be installed as option. It is encoder module which can read/write to the three tracks to the magnetic stripe card in ISO specification. The magnetic track can be saved as SC, SS, TD, ES, LRC,

SC format.

In recording the magnetic data, the location of SS (Start Sentinel) should be apart 7.44 ± 0.5 mm from the card edge as ISO spec. SS location can be adjusted using “Magnetic Space”. If “Magnetic Space” value is higher, it is more far from the card edge.

2014-03-24

SC SS TD (Track Data) ES LRC SC

(SC: Sync Clock pulse, SS: Start Sentinel, ES: End Sentinel, LRC: longitudinal redundancy check)

4.1 Setup

4.1.3.6 Thermal Print Head Replacement

To change the print head, the print head module as below photo should be changed. After change the print head module, its serial no. and register value should be registered. First press “>” button and click “Change Header” and input the serial no. with the resister value which is described on the print head. “Reset User Issue Count” is initialization of the printing number.

(After change the thermal print head, the printing position and thickness should be adjusted.)

(See 3.2.1. for Thermal Print Head Replacement mechanically)

2200169

2615

KPE

B22001692615

2014-03-24

4.1 Setup

4.1.3.7 Security

•

Password

It need to input the password to change the setup value but if you do not set the password, it need not. When execute CardPrinterSetup program, the password input window will be displayed. If you set the password, it is saved to SMART Card Printer itself so even if you change the PC, the password is needed for that card printer.

To change the password, click “Change Password” in basic setup window. It will be activated after the printer is reboot.

(The default is no password setting.)

(If the password is not remember, please contact the manufacturer.)

2014-03-24

4.1 Setup

•

PC Auth.

PC Auth. is a function to operate a SMART printer with specific PC. This is to prevent the access of unauthorized person to print card with another printers. Please read as below.

1. In expansion mode, click “PC Auth.” and “Set Config.”

2. Click “Set PC Serial” and save the current PC information to the card printer.

PC Auth. will be activated after the printer’s rebooting. When connect SMART printer which is applied PC

Authentication to the other PC, “Verify Your PC” message will be displayed on the LCD (or Watchman).

(In case PC Witness is activated and PC is not found, please contact I&A system or your distributor.)

2014-03-24

4.1 Setup

•

Physical Key

Physical Key is the function which is enable to operate SMART printer who have the physical key. It is provided as special option. To use this function, in expansion mode change “Physical Key” to “Use” and press “Set Config.”

Physical Key will be activated after SMART printer reboot. If the printer is locked, “Unlock Please” message will be displayed on LCD and if not, “System Ready” will be displayed.

Physical Key is electrical key so its setup will be kept when the printer is reboot (power off/on).

2014-03-24

4.1 Setup

•

User Auth.

User Auth. allows using PC for someone who knows User password. To activate this function, please tick ‘User

Auth.’ and click ‘Set Config’.

After setting User Auth., this function is activated after re-booting ID card printer. In case printer is locked, LCD

(or Watchman) displays “Unlock Please” message. When you unlock the printer by inputting password using SDK,

“System Ready’ is displayed.

To change password, click ‘Change User Password’ and password change pop up comes up. You can change password and it will be applied after card printer is re-booted.

2014-03-24

4.1 Setup

•

Root Auth.

Root Witness allows using PC for someone (administrator) who knows Root password.

To activate this function, please tick ‘Root Auth.’ and click ‘Set Config’.

After setting Root Auth., this function is activated after re-booting ID card printer. In case printer is locked, LCD

(or Watchman) displays “Unlock Please” message. When you unlock the printer by inputting password using SDK,

“System Ready’ is displayed.

To change password, click ‘Change Root Password’ and password change pop up comes up. You can change password and it will be applied after card printer is re-booted.

2014-03-24

4.1 Setup

•

SBS Only

SMART-30 Printer is provided the printer driver same as other normal printer so it can be used in the application for SMART card printer and other general application. “SBS Only” function can be realized in the application which is developed by our SDK.

To use this function, in the expansion mode, change “SBS Only” to “Use” and press “Set Config.”

SBS Only will be activated after SMART printer is reboot. This SBS Only mode is not activated in other general application.

2014-03-24

4.1 Setup

•

Magnetic Encryption

If the magnetic stripe card is read and write by SMART printer, the magnetic information can be transfer by USB.

“Magnetic Encryption” is define the key which is used to encrypt the magnetic information to prevent that information’s hacking between PC and SMART printer.

To use “Magnetic Encryption”, press “Set Mag. Encryption Key” and input the key you want to use to the dialog.

For the encryption, you can use the magnetic read/write encryption key in SDK provided.

2014-03-24

4.1 Setup

4.1.3.8 Etc.

•

Printer ID

To use SMART-30 printer’s SDK, you have to set the printer which you want to use. And in this case you need to get ID to distinguish the printer and it named as Printer ID. Normally we use one PC and one SMART card printer so do not need to concern. However if use more than one SMART card printer is connected with PC or want to use the several card printer using networking function, you have to set the different Printer ID per each card printer.

To change Printer ID, press “Change Printer ID” and when there is pop up window, input Printer ID and press O.K.

The changed Printer ID will be activated after rebooting of SMART card printer.

The default Printer ID is “SMART.”

2014-03-24

4.1 Setup

•

Use USB Serial

In SMART-30 Card Printer, even if you change the USB port, you do not need to install the printer driver. This is because their own ID is used in USB communication. Basically every printer have their own ID but considering the general usage circumstance and the convenience of maintenance, it is set as same ID. So if want to use more than one printer in one PC, you have set the different ID (this is not same as Printer ID we explained already). Use USB

Serial is ID which is used when the printer is recognized by USB and the serial no. of printer will be used as ID.

To activate Use USB Serial, change “Use USB Serial” to “Use” and press “Set Config.” button. This change will be activated after SMART printer is reboot.

(When use more than one SMART printer in one PC, “Use USB Serial” should be set as “Use”. If not, PC might be not working.)

2014-03-24

4.1 Setup

•

DCL Mode

With DCL mode, you can control card printer without installation of printer driver. It is operated with DCL order in

SDK. You can control this mode with DCL order in SDK but printer driver installation pop-up appears whenever card printer is connected.

If you set ‘DCL Mode’ to ‘Use’, it does not use printer driver and previously installed driver becomes off-line.

In order to use DCL mode, please change ‘DCL Mode’ to ‘Use’ and click ‘Set Config’. This function is activated after card printer is re-booted.

(If DCL mode is activated, you will not use printer on general programs. It is only controlled by DCL order in SDK. )

2014-03-24

4.1 Setup

•

Cleaning Warning

SMART printer checks the cleaning time. At that time, Cleaning message is displayed in LCD window.

In order not to display the cleaning message, please change ‘Cleaning Warning’ to ‘Off’ and click ‘Set Config’.

This function is activated after card printer is re-booted.

2014-03-24

4.2 Test

4.2.1 Overview

CardPrinterTest is to test the all function of SMART Card Printer. To operate CardPrinterTest program, the device driver should be installed to PC and SMART printer should be connected.

Card Printer use the standard printer device driver so it can be printed same as general printer. However if there is encoder, it need to install the driver which the encoder is required. In this case the printer’s detailed operation can be controlled using “Card Printer SDK.” CardPrinterTest program is developed by “Card Printer SDK”.

CardPrinterTest is consist of Choice, Control, Print, Allocation, Encode, State, Message.

① Select : Choose the printer when there is more than one printer is connected.

② Control : Order the command such as Card In, Out, Move and Rotate.

③ Print : Print the image.

④ Allocation : Set the encoding number.

⑤ Encoding : Do magnetic stripe encoding, Smartcard and Contactless Smartcard encoding.

⑥ State : Check the printer’s state.

⑦ Message : Display all kinds of message which displayed when use CardPrinterTest.

2014-03-24

4.2 Test

If execute CardPrinterTest program, the following window will be displayed. It is consist of ① Select, ② Control,

③ Print, ④ Allocation, ⑤ Encoding, ⑥ State, ⑦ Message.

①

Select

②

Control

③

Print

④

Allocation

⑤

Encoding

⑥

State

⑦

Message

2014-03-24

4.2 Test

4.2.2 Basic Operation

4.2.2.1 Selection

The section next to “Printer” is for the printer selection. If you execute CardPrinterTest program, you can find out the below thing and show the available printer list, The displayed thing is “Printer ID”. (explained at 4.1 chapter) In below image, it show there is one printer is connected and its printer ID is “SMART”. Usually one printer is connected so do not much concern for this matter.

(When connect more than two printers to one PC, use after select “USB Serial” in CardPrinterSetup program.

If the printer selection section is not activated, it means there is no printer connected so please check the printer is ON.)

2014-03-24

4.2 Test

4.2.2.2 Control

Control is consist of SBS, Card, Move, Rotate, Etc. and it is used to control the printer’s each step.

• SBS is the operation of SBS (Step-By-Step) mode. The user can control SMART printer using the command. The difference of NORMAL mode and SBS mode is that the printer do printing after get the printing command(DoPrint). If press “Start” in SBS, SMART printer operate as SBS mode and in this time if there is printer spool, it will be removed. To close SBS mode, press “Stop”.

• Card is the command for Card In / Out. “IN” is for moving the card to the printer inside and “OUT” is the command to card out to the stacker. “Back” is to out the card to back side.

• Move is the command to move the card. “Print” is to move the print location, “Mag.” is magnetic location, “IC” is

Smartcard location, “RF” is Contactless Smartcard location, “To Rotate” is move to the inside of rotator, “From

Rotate” is move the card from rotator inside to the printer inside.

• Rotate is for the card flipping. When the card is the printer inside if do “Auto” command, the card is move to rotator and flip and move to the printing location. “Batch” is repeat as set. “To bottom” is the card flip to back side. “To Top” is the card flip to front side. For Etc., “Auto Ribbon Set” is automatically set the ribbon. And using “Use Log”, you can decide to record to the log file or not.

2014-03-24

4.2 Test

4.2.2.3 Print

Print can be used to print the designed image which made by Smart Design. To print the card, use “…” and choose

CSD file. Press “Open” and select CSD file and press “Print”.

When the printer is NORMAL state, if you press “Print”, the data is transfer to SMART printer and print. However in

SBS mode, if press “Print”, the data is transfer to SMART printer and waiting the printing command. So in SBS mode, it need to press “Do Print” for the printing. This function is needed to control the printer in detail.

2014-03-24

4.2 Test

4.2.2.4 Allocation

Allocation is used to test the encoding and decoding continually. Set the repeat no. and if press “Batch Start” it repeat the test. In this case if “Include Card In/Out” section is marked, the card in/out operation is also proceed.

However if it is not checked, use one card continually..

In Strategy, if the retry is not checked, the encoding is placed only one time and it is checked, it is repeat as set when there is an error. If Prompt on Error is checked, the pop up message will be displayed when there is an error.

And if it is not checked, the test is proceeding after an error is counting.

Error is the error number for each encoding.

2014-03-24

4.2 Test

4.2.2.5 Status

State is to check the printer state. If press “Get Temperature”, it display the thermal head’s temperature. In this case if check “realtime check”, the temperature is checked on time.

“Get Status” is to check the printer’s state. It show the ribbon balance, printer condition and error state. If check

“realtime”, on time checking.

2014-03-24

4.2 Test

4.2.2.6 Message

It show the communication detail between CardPrinterTest program and SMART Printer so you can check what kind of command is doing now.

2014-03-24

4.2.3 Encoding

4.2.3.1 Magnetic Stripe

Magnetic encoding is to test the magnetic stripe card when choose “Magnetic” tap as below.

4.2 Test

2014-03-24

4.2 Test

In Magnetic tap, you can do the read/write of the magnetic stripe card.

“Read” is the reading of the magnetic stripe card and show the date. In fact “Read” is consist of “Do Read” and

“Read All Buffer” but operated at one time. “Do Read” is read the magnetic data in the printer inside. “Read All

Buffer” is bring the data to PC. So “Read” is same as “Do Read” and “Read All Buffer”. Only checked track can be concerned.

“Write” is the writing of the magnetic stripe card and record the date. “Write” is also consist of “Write All Buffer” and

“Do Write”. “Write All Buffer” is send the encoding date to the printer, “Do Write” is recording the data to the magnetic card. You can choose “Lo Co”/”Hi Co” as its card type. “Random Fill” is inputting the random date to test.

2014-03-24

4.2 Test

When you tick ‘Bit Mode’, display is changed to Bit Mode writing condition. In the ‘Bit Mode’, you can input data with ‘0’ and ‘1’ only. You can set BPI information in the ‘Bit Mode’.

BPI range: 210 ~ 40,

You can set BPI value: 210, 168, 140, 120, 105, 93, 84, 76, 70, 64, 60, 56, 52, 49, 46, 44, 42, 40

If you set not defined BPI value, above BPI value is set automatically.

(EX) If you set 170 BPI, it becomes 210 BPI.

Bit which can be written on card may be varied in accordance with BPI. Please refer a formula as below,

Bit can be written = 2.8 X BPI

If you use 210BPI, 2.8 X 210 = 588. SO you can write 588 bit.

2014-03-24

4.2 Test

If you want to write and read on magnetic in order, you need to do following procedures.

Card “IN” → Move “Mag” → Magnetic “Random Fill” → Magnetic “Write” → Magnetic “Read” → Card “OUT”

When you select ‘Magnetic’ on the encoding selection tap and click “Batch Start”, magnetic encoding is repeated as below.

2014-03-24

4.2.3.2 Contact Smart Card

Contact Smartcard encoding is enable to encode the date to Smartcard when you choose the IC tap.

4.2 Test

2014-03-24

4.2 Test

In IC tap, the read/write of Smartcard is possible.

“ICH Contact” is the command to contact the head with Smartcard chip. “ICH Discontact” is the dis-contact command. “Init” is the initialization of the installed IC reader. The installed IC reader will be displayed on right down control board. “Contact” is contacting between the IC head and Smartcard. “Reset” is stop to use.

After “Contact”, “Get ATR”, “Read”, “Write” and “Clear” command are possible to operate. “Get ATR” is loading ATR value of Smartcard. “Read” is reading such as name, address, phone data. “Write” is writing.

If read/write the date directly using APDU command, you can use the following APDU command. “Load APDU” is load the saved APDU command. “Save APDU” is save the current APDU command. “Clear APDU” is clear the APDU screen. To see the individual APDU command, press “Send APDU” on the line..

To write and read on Smartcard, you have to proceed the following procedure.

Card “IN” → Move “IC” → IC “ICH Contact” → IC “Init” → IC “Contact” → IC “Write” → IC “Clear” → IC “Read” → IC

“Reset” → IC “ICH Dis-contact” → Card “OUT”

If press “Batch Start”, IC encoding will be repeated. SMART Printer is support the internal Smartcard encoder and external SIM encoder. SIM is not possible to move automatically so the batch is not possible for SIM.

2014-03-24

4.2 Test

4.2.3.3 Contactless (PC/SC) Smart Card

Smartcard encoding through PC/SC – The contactless smartcard can be tested through PC/SC protocol after select

“RF (PC/SC)” tap of CardPrinterTest program.

2014-03-24

4.2 Test

In RF (PC/SC) tap, the read & write to the contactless smartcard can be done.

“Init” is the command to show the installed PC/SC type reader. The available reader will be shown to the left full down control. “Contact” is the command for the connection to the contactless smartcard and “Reset” is the disconnection.

After “Contact”, “Get UID”, “Read”, “Write” and “Clear” can be executed. “Get UID” is the reading command for RF chip’s serial value. “Read” is also the reading command for the data such as name, address and phone which are predefined. “Write” is the writing command for name, address and phone.

When read and write to the contactless smartcard using APDU command, you can use the below APDU command.

“Load APDU” is loading of the saved APDU command and “Save APDU” is saving the current displayed APDU command. “Clear APDU” is clearing. To send the individual APDU command, you just press “Send APDU” which you want.

To write and read from the contactless smartcard, you have to follow the below procedure.

Card “IN” → Move “from In (-62)” → RF (PC/SC) “Init” → RF (PC/SC) “Contact” → RF (PC/SC) “Write” → RF (PC/SC)

“Read” → RF (PC/SC) “Reset” → Card “OUT”

After select “RF (PC/SC)” in tap, if you press “Batch Start”, the encoding will be repeated. SMART printer have the internal installed contactless smartcard encoder and external installed contactless smartcard encoder. For the external contactless smartcard encoder, you can test by not marking “Internal (Batch)” item.

2014-03-24

4.2 Test

4.2.4 Status

4.2.4.1 Printer Status Code

SMSC_M_CARDIN

SMSC_M_CARDOUT

SMSC_M_MOVE_PRINT

SMSC_M_MOVE_PRN2ROT

SMSC_M_MOVE_ROT2PRN

SMSC_M_MOVE_IC

SMSC_M_MOVE_RF

SMSC_M_MOVE_MAG

SMSC_M_THUP

SMSC_M_THDOWN

SMSC_M_ICHUP

SMSC_M_ICHDOWN

SMSC_M_PRINT

SMSC_M_MAGRW

SMSC_M_SEEKRIBBON

SMSC_M_MOVERIBBON

SMSC_M_ROTATORTOP

SMSC_M_ROTATORBOTTOM

SMSC_S_HOPPERHASCARD

SMSC_S_CLEANWARNING

SMSC_S_CARDIN

SMSC_S_CARDOUT

SMSC_S_EQUIPLAMINATOR

SMSC_S_EQUIPROTATOR

SMSC_M_RECVPRINTDATA

SMSC_S_HASPRINTBUFFER

SMSC_M_SBSRUNNING

SMSC_S_SBSMODE

SMSC_S_CASEOPEN

SMSC_M_INIT

SMSC_S_TESTMODE

2014-03-24

0x0000000000000001

0x0000000000000002

0x0000000000000004

0x0000000000000008

0x0000000000000010

0x0000000000000020

0x0000000000000040

0x0000000000000080

0x0000000000000100

0x0000000000000200

0x0000000000000400

0x0000000000000800

0x0000000000001000

0x0000000000002000

0x0000000000004000

0x0000000000008000

0x0000000000010000

0x0000000000020000

0x0000000000040000

0x0000000000080000

0x0000000000100000

0x0000000000200000

0x0000000000400000

0x0000000000800000

0x0000000001000000

0x0000000002000000

0x0000000004000000

0x0000000008000000

0x0000000010000000

0x0000000020000000

0x0000000080000000

// Under Card In

// Under Card Out

// Move to Printing Position

// Move to Flipper from Printer

// Move to Printer from Flipper

// Move to IC Position

// Move to RF Position

// Move to Magnetic Stripe Position

// Thermal Print Head Up

// Thermal Print Head Down

// IC Head (Contactor) Up

// IC Head (Contactor) Down

// Under Printing

// Magnetic Stripe Read/Write

// Searching Ribbon

// Moving Ribbon

// Card Front Side Flipping to Up

// Card Front Side Flipping to Down

// Card is in the Hopper

// Need to cleaning State (After firmware 1.00.60)

// Card Detection by Card In Sensor

// Card Detection by Card Out Sensor

// Laminator is installed (After firmware 1.00.60)

// Flipper is installed

// Receiving Printing Buffer

// Reserving Printing Data Buffer

// Doing SBS Command

// SBS Mode State

// Case Open State

// Under Initialization

// Test Mode State

4.2 Test

Status codes are changed after Printer firmware 1.00.60 as below.

SMSC_S_CLEANWARNING

SMSC_S_THUP

SMSC_S_EQUIPLAMINATOR

SMSC_S_ROTATORTOP

0x0000000000080000

0x0000000000400000

// Need to cleaning State (After f/w 1.00.60

)

// Thermal Print Head Up state (Before f/w 1.00.60)

// Laminator is installed (After f/w 1.00.60)

// Card Front Side is up at Rotator (Before f/w 1.00.60)

2014-03-24

4.2.4.2 Printer Error Code

SMSC_F_CARDIN

SMSC_F_MOVETOPRINT

SMSC_F_CARDOUT

SMSC_F_MOVETOMAG

SMSC_F_MOVETOIC

SMSC_F_MOVETORF

SMSC_F_MOVETOROTATOR

SMSC_F_MOVEFROMROTATOR

SMSC_F_THUP

SMSC_F_THDOWN

SMSC_F_ICHUP

SMSC_F_ICHDOWN

SMSC_F_ROTATORTOP

SMSC_F_ROTATORBOTTOM

SMSC_F_PRINT

SMSC_F_MAGRW

SMSC_E_SEEKRIBBON

SMSC_E_MOVERIBBON

SMSC_E_NOTH

SMSC_E_THOVERHEAT

SMSC_E_EMPTYRIBBON

SMSC_F_DATA

SMSC_F_CARDBACKOUT

SMSC_F_CARDERASE

SMSC_F_INCORRECT_PW

SMSC_F_MAGREADT1

SMSC_F_MAGREADT2

SMSC_F_MAGREADT3

SMSC_F_LOCKED

SMSC_F_SPOOLFULL

SMSC_F_SET

0x0000000100000000

0x0000000200000000

0x0000000400000000

0x0000000800000000

0x0000001000000000

0x0000002000000000

0x0000004000000000

0x0000008000000000

0x0000010000000000

0x0000020000000000

0x0000040000000000

0x0000080000000000

0x0000100000000000

0x0000200000000000

0x0000400000000000

0x0000800000000000

0x0001000000000000

0x0002000000000000

0x0004000000000000

0x0008000000000000

0x0010000000000000

0x0020000000000000

0x0040000000000000

0x0080000000000000

0x0100000000000000

0x0200000000000000

0x0400000000000000

0x0800000000000000

0x1000000000000000

0x2000000000000000

0x4000000000000000

// Card In Fail

// Moving to Printing Position is Fail

// Card Out is Fail

// Moving to Magnetic Position is Fail

// Moving to IC Position is Fail

// Moving to RF Position is Fail

// Moving to Flipper is fail

// Moving to Printer from Flipper is Fail

// Thermal Print Head Up Fail

// Thermal Print Head Down Fail

// IC Head (Contactor) Up Fail

// IC Head (Contactor) Down Fail

// Card Front Side Flipping to Up is Fail

// Card Front Side Flipping to Down is Fail

// Error in Printing

// Magnetic Stripe Track Read/Write Fail

// Ribbon Search Error

// Ribbon Move Error

// Thermal Print Head is not Installed

// Thermal Print Head Overheat

// Empty Ribbon

// Printing Data Error

// Card Back Out Fail

// Card Data Erase Fail

// Incorrect Password

// Magnetic ISO Track 1 Read Fail

// Magnetic ISO Track 2 Read Fail

// Magnetic ISO Track 3 Read Fail

// Printer Locked

// Spooler Full

// Recently Printer Operation Fail

4.2 Test

2014-03-24

4.3 Firmware

4.3.1 Overview

CardPrinterFirmware is the software for changing the firmware of SMART printer. The firmware of SMART printer is the operating software for the processor of SMART printer. If new function is added or there is other reason, it will be provided by web-site or distributor.

Printer ID

Device selection tab

Current firmware version

New firmware

Main buttons

Messages

2014-03-24

4.3.2 Automatic Update

Printer Update is the same as Laminator Update. The upgrade procedure is as follows.

1.Check the current printer’s firmware version.

2.Press “Browse” button and select the firmware you want to install.

3.Press “Update” button and update.

4.Click “OK” on dialogue message to continue the update.

5.Waiting until the firmware update is finished.

1. Check current firmware version

2. Browse new firmware

3. Push Update buttons

4.3 Firmware

4. Push OK button

( In firmware update, the printer is automatically rebooted.)

( During update, please do not operate the printer or close the program.)

2014-03-24

4.3.5 Manual Update

Manual update procedure is as follows.

1.Check the printer’s firmware version.

2.Press “Browse” button and select the firmware you want to install.

3.If press “Manual Update”, “Manual Update Instruction” window will be displayed.

4.Follow “Manual Update Instruction”.

5.If press “Transfer” and transferring is complete, window will be closed.

6.Waiting until the firmware update is finished.

1. Check current firmware version

2. Browse new firmware

3. Push “Manual Update” button

4.3 Firmware

( In firmware update, follow the instruction and do not operate other thing.)

2014-03-24

5.1 General Operation

Symptom

When the ribbon is torn

Countermeasures

Open the top cover and pull out the ribbon cartridge. Connect the ribbon and install again. If the problem is occurred too often, refer to the below countermeasures.

Check the card specification or change to the new one.

2 The color density setting is too high Refer to the manual 4.1.3.2 and adjust the printing density.

3 The card printing position is not proper

Adjust the image start position as 0.5mm from the card starting point. If the problem is not solved, refer to the manual 4.1.3.1.

Ribbon is not recognized. – There will be displayed

“ Ribbon Not Found” error message.

Press the left button of front LCD to replay. If the problem is not solved, refer to the below countermeasures.

1 Ribbon tag is bad Change to the new ribbon.

2 All ribbon is used

3 Ribbon is torn

Change to the new ribbon.

Open top cover and pull out the ribbon cartridge. Connect the ribbon.

4 Thermal print head is not properly installed

5 Ribbon is not authorized one

Refer to the manual 3.2.1 and check the Print Head installation state.

Change to the authorized one.

Related Parts

2014-03-24

5.1 General Operation

Symptom

6 Color In Sensor or Color Out Sensor is bad

Countermeasures

When Color In/Out Sensor have some problem, replace the sensors.

Change the Color In Sensor

- Manual 3.2.4

Change the Color Out Sensor

Related Parts

630026(SENSOR COLOR OUT2

BD,SMART,0.3)

630024(SENSOR COLOR IN

BD,SMART,0.4)

7 Encoder sensor or connection cable is bad

Bad connection status of sensor cable may make this error (See 2.1)

Refer to the manual 3.4.3 and replace the cable or sensor.

9 Ribbon RF Board’s connection cable is bad

10 Main board is bad

Refer to the manual 3.3.2 and change the connection cable.

Refer to 3.3.1 and replace the main board.

630033(SENSOR ENCODER2

BD,SMART,0.1)

611076(WIRE,I/O_30 LEFT,20P,230mm)

630020(RIBBON RF,SMART,0.2)

611079(FFC CABLE,240mm,16P,

0.5mm,2896 C-type)

630083 (MAIN BD,SMART,0.57)

2014-03-24

5.1 General Operation

Symptom

Printer is not working even if the printing data is sent or the printer is not booting.

1 Printer power is off.

2 Using another DC adaptor.

3 Printer driver is not online but offline.

Countermeasures

Refer to the below countermeasures.

Power on the printer.

Check DC adaptor and use our adaptor which supplied with the printer.

Change to the online.

Check the state and plug out and in for USB cable.

Print through the proper printer driver

6 Printer driver port setting is wrong. Check the printer driver port setting is USB port.

Install the ribbon or clear the printer error refer to this manual.

8 Ribbon balance is 0.

Power and communication cable are too long.

(Power cable : Over 1.5 M, communication cable : Over 1.8M)

10 USB port of PC is down.

Change to the new ribbon.

Using the cable which supplied from us.

Reboot PC.

11 The printer communication USB cable is bad

12 Power adaptor is bad

13 Printer is bad

Change USB cable.

Call to the nearest dealer and change it.

The printer should be replaced

Related Parts

610120(CABLE,USB2AB1,1.8M,

USB1.0)

610697(ADAPTOR,STD-

2427P,24V/2.7A,-)

2014-03-24

5.2 Card Moving

Symptom

Card is not inserted from the hopper

1 Card size is not correct or it is not proper card

3 Card arrangement is not proper

4 There is electrical static or moisture on the card

5 The hopper unit or connection cable are bad

When there is moving error as the ribbon is rolled to the printing roller or movement rollers.

1 Card size is not correct or it is not proper card

2 The printer’s printing position is set no properly

Countermeasures

Press the left key on the front side of printer to replay. If it is not moving and the problem is happen so often, please refer to the below countermeasures.

If the card is not in specification., it might be not inserted to the hopper. It should be changed.

Related Parts

Refer to 1.2.2 and adjust the card thickness .

Arrange the cards as the manual 1.2.3 and put the cards again to the hopper.

If the card hopper is totally not working, check the connection of card hopper and if there is no problem, the hopper cable and hopper should be changed.

630097(HEAD UD MOTOR_30

BD,SMART30,0.1)

611076(WIRE,I/O_30

LEFT,20P,230mm)

Open the top cover, remove the ribbon which rolled to the card and roller using the front LCD buttons. If the problem is happen so often, please refer to the below countermeasures.

If the card size is more large or small, the printing position might be not correct. Refer to the manual 4.1.3.1 and reset the printing position or change the card.

If the card size is more large or small, the printing position might be not correct. Refer to the manual 4.1.3.1 and reset the printing position.

2014-03-24

5.2 Card Moving

Symptom

When there is an error during card movement

1 Card size is not correct or it is not proper card

2 Using another DC adaptor.

3 There is dust on the surface of cards

Countermeasures

Press the left key on the front side of printer to replay. If it not moving and the problem is happen so often, please refer to the below countermeasures.

Change to the proper card.

Some problem might be happened if use another DC Adaptor which is not supplied with the product. Please check DC Adaptor.

※ If use other DC Adaptor, Magnetic stripe encoding error or other operation problem can be occurred.

Clean the card or change to new card.

Clean the cleaning roller using the cleaning card kit. The related rollers are IC roller, cleaning roller fixed, MS(Magnetic Stripe) roller.(See 2.2 Thermal Head and Rollers)

Related Parts

4 There is dust on the moving rollers

2014-03-24

100

5.3 Printer Noise

Symptom Countermeasures

When print, there is a big bang sound at the end of printing.

Card side is not in specification or the setting is not proper.

Refer to the manual 4.1.3.1 and reset or change the card.

There is ribbon gear noise as the printer is not properly wind the ribbon.

Ribbon is winding on the gear side of ribbon core so it is get out of gear. Remove the ribbon on the ribbon core gear.

If there is not enough lubricant oil, this kind of noise can be occurred. In this case the lubricant oil should be varnished as below instruction.

Related Parts

There is a frictional noise during card movement Lubricant Oil

2014-03-24

101

5.4 Printing Quality

Symptom

Some parts of a card are not printed or printed in different colors

1 When there is dust on the surface of card

3 There is too much dust inside of the printer

When there is not printed lines

2 When there is dust on the Print Head

Countermeasures Related Parts

It can be happened if the printer is not used for a long time or not clean card is used. Change the card and try to print again. If the problem is occurred so often, refer to the below countermeasures.

Remove the dust on card surface or change to the new card.

If the cleaning roller is contaminated, change to the new one.

※ If the printer is not used for long time, the adhesive power of the disposable cleaning roller is decreased so in this case, it should be changed to new one.

Remove the dust inside of the printer

This can be occurred when there is dust on the Thermal Print Head or the Print Head thermal line is damaged. Refer to the below countermeasure.

Disposable

Cleaning Roller

Check the ribbon cartridge’s installation state and whether the ribbon panel is wrinkled.

Clean the Print Head using the cleaning kit.

3 Thermal Print Head surface is damaged

4 Thermal Print Head’s thermal line is damaged

The Print Head should be changed. Refer to the manual 3.2.1./ 4.1.3.6 and change.

The Print Head should be changed. Refer to the manual 3.2.1 / 4.1.3.6 and change.

640257(ASSY

S3,PRINT_HEAD_KPE)

640257(ASSY

S3,PRINT_HEAD_KPE)

2014-03-24

102

Symptom

Pictures are not smooth or blurred

5.4 Printing Quality

Countermeasures

It can be happened when the printing density is set too low. Increase the printing density value and if the problem not solved, refer to the below countermeasures.

※ Refer to the manual 4.1.3.2.

Related Parts

1 The card surface is not even and it have a faulty

2 The color density is not proper

3 Thermal Print Head surface is contaminated

Check the card surface or change to the new card.

Reset the printing density refer to the manual 4.1.3.2.

Clean the Print Head with the cleaning kit.

103

2014-03-24

5.4 Printing Quality

Symptom

If the color matching is wrong

1 the movement and printing roller are contaminated

Countermeasures

It might be the problem of printing position. The image starting position should be 0.5mm. If the problem is not solved, refer to the below countermeasures.

※ Reset the position as manual 4.1.3.1.

Clean the surface of rollers which described as follows. The related rollers are

IC roller, Printing roller, MS roller.

Related Parts

In case the installation of Card In Sensor is not good, the position can be move. Please check the sensor’s condition.

2 the installation of the Card In sensor is bad

3 Card In Sensor is bad

When the Card In Sensor is bad, it might be not set the correct position. The

Card In Sensor should be changed.

630110(SEN_POS_30

BD,SMART30,0.2)

2014-03-24

104

5.4 Printing Quality

Symptom

When the side part of card is not printed

Countermeasures

It might be occurred when the print density is set too low.

Increase the printer printing density and if the problem is not solved, refer to the below countermeasures.

※ Adjust the density refer to the manual 4.1.3.2.

Related Parts

Check the ribbon cartridge’s installation state and whether the ribbon panel is wrinkled.

2 The card surface is not even and it have a faulty Check the card surface or change to the new card.

Clean the Print Head using the cleaning kit.

3 In case the Print Head is contaminated

105

2014-03-24

Symptom

When the following problem is occurred

Countermeasures

If print too dark image, this kind of problem might be happened. Refer to the manual 4.1.3.2 and adjust the printing density. If the problem is not cleared, using plus type driver and adjusting it until the problem is removed.

5.4 Printing Quality

Related Parts

When the card is out without printing

In case the Print Head is not properly installed or the

Print Head cable connection is bad, this kind of problem might be happened. Refer to the manual 3.2.1 and check the Print Head and cable connection state. If the state is normal, the Print Head should be changed.

640257(ASSY S3,PRINT_HEAD_KPE)

If the card printing operation is not working except the card movement

Please check the adaptor connection state. In the case of using other adaptor, this fault may occur. Please check the authorized adaptor is used .

106

2014-03-24

5.5 Magnetic Stripe Read/Write

Symptom

In case there is the magnetic stripe encoding read/write error

In case the magnetic stripe read/write error is occurred too often

3 The anti-magnetic force is not proper

Countermeasures

Press the left button of front LCD to replay.

Refer to the below countermeasures.

Check the program and driver’s version and the matching between the data and track.

Change the card or place the card correctly.

The range of anti-magnetic force is LoCo(300Oe~600Oe),

HiCo(1750Oe~4000Oe). Check the magnetic stripe card’s spec.

4 The magnetic stripe of card is bad

6 The magnetic stripe head is contaminated

Related Parts

Check the read/write ability of card and change to new one.

The cable between M8 board and M8 head should be installed like Z type to the printer hopper. If the cable is not properly installed, it will be affected by the step motor noise. Refer to the manual C.1

Refer to the manual C.1 and uninstall the magnetic stripe head and clean with the cleaning kit.

Clean the magnetic stripe head surface. Refer to the manual C.1 and check the head state, if there is no problem, the magnetic board

(89030231) or main board should be replaced. When change the main board, refer to the manual 3.3.1.

630096(MS MAIN BD,SMART,0.5)

630083(MAIN BD,SMART,0.57)

2014-03-24

107

5.6 Flipper

Symptom

Flipper is not recognized

Flipper is not working

Check the program setting

2 The flipper connection cable is bad

3 The flipper cable or flipper is bad

4 Main board is bad

When there is card jam in flipping

Countermeasures

In case there is no flipper operation sound when the printer is initialized or the flipper is not recognized, check the flipper cable connection state. Refer to the

C.2 and check it.

Refer to the below countermeasures.

Check it is set as both side in the printer properties.

Related Parts

Check the flipper connection cable state. Refer to the manual C.2 and check it.

Change the flipper cable or flipper. Refer to the manual C.2 and change it.

Change the main board.

640288(ASSY

S3,FLIPPER_OPTION)

610148(FFC CABLE,350MM

30P, 0.5MM,2896 CTYPE)

630083 (MAIN

BD,SMART,0.57)

Press the left button of front LCD to replay. If the problem is not removed, power off and open the rear cover of flipper and remove the card. If this problem is happen so often, please refer to the below countermeasures.

1 The flipper setting value is changed. Refer to the manual 4.1.3.4 and adjusting the flipper.

2 The flipper cable or flipper is bad

3 Main board is bad

Refer to the C.2 and change it.

Change the main board

640288(ASSY

S3,FLIPPER_OPTION)

610148(FFC CABLE,350MM

30P, 0.5MM,2896 CTYPE)

630083 (MAIN

BD,SMART,0.57)

2014-03-24

108

A. Service Parts List

NO.

A.1

A.2

A.3

A.4

A.5

A.6

A.7

A.8

A.9

A.10

2014-03-24

Item

BOARD

SENSOR

CABLE

FFC

CASE

MOTOR

BELT

ROLLER

ETC

OPTION

A. Service Parts List

109

A.1 BOARD

NO CODE NO.

1 630083

2 630020

3 630050

ITEM

MAIN BOARD

RIBBON RF BOARD

USB HUB BOARD 1

DESCRIPTION

MAIN BD,SMART,0.57

RIBBON F BD,SMART,2.0

USB HUB BD,SMART,0.1

630096

630104

MS BOARD

INTERNAL RF BOARD

MS MAIN BD,SMART,0.5

IN_RF_GENDER_30 BD,SMART30,0.1

6 630070 PCBA-EHTERNET MAIN ASS’Y NETWORK HUB BD EDDY-CPU V2.5-ASSY

PHOTO

C.1

C.4

C.6

PAGE

3.3.1

B.1.4

B.2.10

3.3.2

B.2.4

C.5

A.1 BOARD

2014-03-24

110

A.2 SENSOR

NO CODE NO.

1 630019

ITEM

HEAD UP-DOWN SENSOR

2 630101

3 630024

4 630026

5 630033

6 630098

7 630103

CARD IN_OUT SENSOR

COLOR IN SENSOR

COLOR OUT SENSOR

ENCODER SENSOR

CASE ON/OFF SENSOR

IC UP-DOWN SENSOR

DESCRIPTION

SENSOR DETECTOR BD,SMART,0.4

SEN_POS_30 BD,SMART30,0.2

SENSOR COLOR IN BD,SMART,0.4

SENSOR COLOR OUT2 BD,SMART,0.3

SENSOR ENCODER2 BD,SMART,0.1

SEN_CASE_30 BD,SMART30,0.1

IC_CAM_SW_30 BD,SMART30,0.2

PHOTO PAGE

2.1

B.2.1

2.1

B.2.3

2.1

B.1.1.1

2.1

B.2.7

2.1

B.2.2

2.1

B.2.1

C.3

A.2 SENSOR

2014-03-24

111

A.3 CABLE

NO CODE NO.

1 611075

2 611076

3 611077

4 610132

5 611078

6 610137

7 610120

ITEM

IO CABLE R

IO CABLE L

LED CABLE

HEAD CABLE

IC SENSOR CABLE

RF IN CABLE

USB CABLE

DESCRIPTION

WIRE,I/O_30 RIGHT,20P,420mm

WIRE,I/O_30 LEFT,20P,230mm

WIRE,LED_30 SW,5P,220mm

WIRE,THERMAL HEAD,26P,370MM

WIRE,IC_30 MOT SEN,6P,210mm

WIRE,OMNIKEY RF IN USB,170MM,USB1.0

CABLE,USB2AB1.8M,1.8M,USB1.0

PHOTO PAGE

B.1.4

C.3

C.4

1.1.1

B.2.15

A.3 CABLE

2014-03-24

112

A.4 FFC

NO CODE NO.

1 611079

2 610146

3 611080

ITEM

RIBBON RF

MS FFC

IC FFC

DESCRIPTION

FFC CABLE,240mm,16P,0.5mm,2896 C-type

FFC CABLE,170mm,16P,0.5mm,2896 C-type

FFC CABLE,37mm,8P,1mm,2896 C-Type

PHOTO PAGE

3.3.2

C.1

C.3

A.4 FFC

2014-03-24

113

A.5 CASE

NO CODE NO.

1 611042

2 611034

3 611089

4 611040

5 611039

6 611035

7 611039

ITEM

TOP COVER

TOP CASE OPEN BUTTON

HOPPER COVER

SIDE COVER R

SIDE COVER L

PRINTER BACK COVER

STACKER

DESCRIPTION

COVER S3,TOP

BUTTON S3,TOP

ASSY S3,FRONT_COVER

COVER S3,SIDE_R

COVER S3,SIDE_L

COVER S3,BACK

COVER S3,STACKER

2014-03-24

PHOTO PAGE

B.2.11

B.1.1.3

B.2.11

B.2.12

B.2.11

B.2.12

A.5 CASE

114

NO CODE NO.

8 610079

9 610490

ITEM

RIBBON CARTRIDGE

FOOT

DESCRIPTION

CASE SS,CARTRIDGE

ASSY SS,FOOT_RUBBER_LA0621

PHOTO PAGE

B.2.13

B.1.13

B.2.10

A.5 CASE

2014-03-24

A.6 MOTOR

NO CODE NO.

1 630058

2 630097

3 640264

ITEM

RIBBON MOTOR

HEAD DOWN/UP MOTOR

PRINT STEP MOTOR

DESCRIPTION

RIBBON MOTOR BD,SMART,0.4

HEAD UD MOTOR_30 BD,SMART30,0.1

ASSY S3,STEP_MOTOR

PHOTO PAGE

B.2.1

B.1.7

B.2.4

A.6 MOTOR

2014-03-24

A.7 BELT

NO CODE NO.

1 611010

2 610913

ITEM

STEP BELT

RIBBON FEEDING BELT

DESCRIPTION

BELT S3,50S2M160

BELT SS,PI39.7X3.5_SILICONE

PHOTO PAGE

B.2.9

B.2.8

A.7 BELT

2014-03-24

A.8 ROLLER

NO CODE NO.

1 611063

2 611067

3 610920

4 611095

5 611066

6 611064

7 611065

ITEM

FIX ROLLER

MS ROLLER

CLEANING ROLLER

PRINTING ROLLER

IC ROLLER

HOPPER ROLLER 1

HOPPER ROLLER 2

DESCRIPTION

ROLLER S3,CLEANING_FIX

ROLLER S3,MS

ROLLER SS,CLEANING,1.1

ASSY S3,ROLLER PRINTING

ROLLER S3,IC

ROLLER S3,HOPPER_CARD_IN_1

ROLLER S3,HOPPER_CARD_IN_2

PHOTO PAGE

2.2

B.2.5

2.2

B.2.5

3.5.1

B.1.8

B.2.7

2.2

B.2.5

2.2

B.2.5

2.2

B.2.5

2.2

B.2.5

A.8 ROLLER

2014-03-24

A.9 ETC

NO CODE NO.

1 610344

2 651089

3 640266

4 630105

5 610697

ITEM

FAN

PRINT HEAD ASS'Y

DISPLAY PANEL

MS HEAD

ADAPTOR

DESCRIPTION

FAN,AD0524HB-G70(T)/LF

SP S3 PRINT_HEAD_ASSY_KPE

ASSY S3,FRONT_DISPLAY

MS_TG313RWVPH_30 BD,SMART30,0.1

ADAPTOR,STD-2427P,24V/2.7A,-

PHOTO PAGE

B.1.1.3

B.1.3

B.2.13

B.1.11

B.2.10

C.1

1.1.1

B.2.15

A.9 ETC

2014-03-24

A.10 OPTION

NO CODE NO.

1 651084

ITEM

MAGNETIC ENCODER

DESCRIPTION

SP S3 MAGNETIC_ENCODER

SP S3 FLIPPER 2 651107 FLIPPER

3 651079 INTERNAL SMART CARD ENCODER SP S3 INTERNAL_SMART_CARD_ENCODER

4 651081

INTERNAL CONTACTLESSSMART

CARD ENCODER

SP S3 INTERNAL_CONTACTLESS_CARD_ENCODER1

5 650967 ETHERNET HUB SP SS NETWORK_HUB

PHOTO PAGE

C.1

C.4

C.6

C.2

C.3

A.10 OPTION

2014-03-24

B. Expanded View

B.1 PHANTOM PARTS EXPANDED VIEW

B.2 MAIN PARTS EXPANDED VIEW

B.3 FLIPPER OPTION PARTS EXPANDED VIEW

B. Expanded View

2014-03-24