advertisement
USER MANUAL
– EN
IN 20217 Exercise bike inSPORTline Omahan UB
CONTENTS
2
SAFETY INSTRUCTIONS
•
Read the manual carefully and keep it for future reference.
•
To ensure the best safety of the exerciser, regularly check it on damages and worn parts.
•
If you pass on this exerciser to another person or if you allow another person to use it, make sure that that person is familiar with the content and instructions in these instructions.
•
Only one person should use the exerciser at a time.
•
Before the first use and regularly make sure that all screws, bolts and other joints are properly tightened and firmly seated.
•
Before you start your work-out, remove all sharp-edged objects around the exerciser.
•
Only use the exercise for your work-out if it works flawlessly.
•
Any broken, worn or defective part must immediately be replaced and/or the exerciser must no longer be used until it has been properly maintained and repaired.
•
Parents and other supervisory persons should be aware of their responsibility, due to situations which may arise for which the exerciser has not been designed and which may occur due to children ’s natural play instinct and interest in experimenting.
•
If you do allow children to use this exerciser, be sure to take into consideration and assess their mental and physical condition and development, and above all their temperament.
Children should use the exerciser only under adult supervision and be instructed on the correct and proper use of the exerciser. The exerciser is not a toy.
•
Make sure there is sufficient free space around the exerciser when you set it up min 0.6 m.
•
To avoid possible accidents, do not allow children to approach the exerciser without supervision, since they may use it in a way for which it is not intended due to their natural play instinct and interest in experimenting.
•
Please note that an improper and excessive work-out may be harmful to your health.
•
Please note that levers and other adjustment mechanisms are not projecting into the area of movement during the work-out.
•
No adjustable part may protrude and limit user movement.
•
When setting up the exerciser, please make sure that the exerciser is standing in a stable way and that any possible unevenness of the floor is evened out.
•
Always wear appropriate clothing and shoes which are suitable for your work-out on the exerciser. The clothes must be designed in a way so that they will not get caught in any part of the exerciser during the work-out due to their form (for example, length). Be sure to wear appropriate shoes which are suitable for the work-out, firmly support the feet and which are provided with a non-slip sole.
•
Be sure to consult a physician before you start any exercise program. He may give you proper hints and advice with respect to the individual intensity of stress for you as well as to your work-out and sensible eating habits.
•
Maximal weight: 150 kg
•
Category: HC for home use (EN 957)
IMPORTANT NOTES
•
Assemble the exerciser as per assembly instructions and be sure to only use the structural parts provided with the exerciser and designed for it. Prior to the assembly, make sure the contents of the delivery is complete by referring to the parts list of the assembly and operating instructions.
3
•
Be sure to set up the exerciser in a dry and even place and always protect it from humidity. If you wish to protect the place particularly against pressure points, contamination, etc., it is recommended to put a suitable, non-slip mat under the exerciser.
•
The general rule is that exercisers and training devices are no toys. Therefore, they must only be used by properly informed or instructed persons.
•
Stop your work-out immediately in case of dizziness, nausea, chest pain or any other physical symptoms. In case of doubt, consult your physician immediately.
•
Children, disabled and handicapped persons should use the exercise only under supervision and in presence of another person who may give support and useful instructions.
•
Be sure that your body parts and those of other persons are never close to any moving parts of the exerciser during its use.
•
When adjusting the adjustable parts, make sure they are adjusted properly and note the marked, maximum adjusting position, for example of the saddle support, respectively.
•
Do not work out immediately after meals!
WARNING! A system for monitoring heart rate may not be accurate. Overloading during training may cause serious injury or death. If you feel any discomfort, immediately stop the exercise!
PRODUCT DESCRIPTION
1. Console
2. Handlebars
3. Middle post
4. Front stabilizer
5. Pedal – L
6. Rear stabilizer
7. Seat
8. Bottle holder
4
TECHNICAL SPECIFICATIONS
Model
Unfolded dimension
Maximal load capacity
Speed ratio
Flywheel
Saddle adjustment - Vertical
Saddle adjustment - Horizontal
B30
1090 x 560 x 1490 mm
150 kg
10.3
External, magnetic, one directional Φ280/9 kg
10 positions, 270 mm
70 mm
5
ASSEMBLY
Prepare all parts and tools in clean and free space.
Follow each step carefully.
6
ASSEMBLY MATERIAL
No.
26 Allen screw
27 Flat washer
28 Spring washer
29 Screw
32 Screw
87 Screw
Allen key
Allen key
Wrench
Name
7
Specification
M10×70×20
Φ 10
Φ 10
M4×6
M4×16
ST4×12
5×80×80S
6 ×66×140 t4.0×38×145
4
1
6
6
Qty
4
4
4
1
1
STEP 1
Attach the front stabilizer (2) to the main frame using the washer (28), spring washer (27) and bolt
(26).
8
STEP 2
Attach the rear stabilizer (3) to the main frame (1) using the curved washer (28), spring washer (27) and bolt (26).
STEP 3
Attach the seat post (4) to the main frame (1).
9
STEP 4
Attach the seat (5) to the seat support (60) using the nuts (59).
STEP 5
Attach the seat (5) to the seat post (4) using the nut (25) and the hand screw (23).
Secure the L-seat cover (16) and the R-seat cover (17) to the seat post (4) with the screws (29).
10
STEP 6
Attach the bolt (31) to the main frame (1).
Connect the motor communication cable (10) and the console communication cable (9).
Attach the center post (6) to the main frame (1). Bolts (31) are preassembled. Attach the post (6) to the main frame (1) and then one by one tighten the preassembled bolts (31). Then attach the caps
(88).
STEP 7
Attach the handles (7). Pass the pulse measurement cables (11) through the hole in the middle post
(6). Then attach the hand screw (21) to the handle cover (13).
Attach the bottle holder (20) to the middle post (6) with the screw (32).
11
STEP 8
Connect the console communication cable (9) to the back of the console. Connect the pulse cable from the handles (11) to the console (12).
Attach the bracket (8) to the middle post (6) with the screws (24).
STEP 9
Attach the handle covers (14 and 15) to the center post (6) with the screws (32).
Attach the front handle cover (13) with the screws (87).
12
STEP 10
Attach the pedal L (18) and pedal R (19) to the main frame (1).
STEP 11
Plug in the power.
13
CONSOLE
Buttons
Up
Down
Mode / Enter
Reset
Start / Stop
Recovery
Body fat
Function
Time
Increase load / navigation key
Decrease load / navigation button
Confirm settings or selections
Holding the button for 2 seconds resets the setting / entering the setting / returning to the main menu in the setting or pausing mode
Starts or stops the device
Orientation test, which evaluates your physical condition after training
Body test program, available if no other program is running
Speed
RPM
Distance
Calories
Pulse
Watts
Manual
Beginner
Advance
Sporty
Cardio / H.R.C
Watt program
User program
Without setting, the time will be added from 00:00 to 99:59, time is added by 1 min
With the setting, the time will be counted from the set time to 00:00 after one minute
Range from 00:00 to 99:59, time is added by 1 min
Current speed, max. 99.9 km / h (mph)
Current speed of the flywheel
Range from 0.00 to 99.00
Distance from 0.00 to 99.99 km (miles).
The user can set the target distance using the UP / DOWN buttons.
The increase is by 1 km, range from 0.00 to 99.00
Displays calories burned from 0 to 9999 calories.
The changes are by 1 calorie, ranging from 0 to 9999.
The data are for guidance only, not for medical purposes
The user can set a target heart rate from 0-30 to 230.
An alarm sounds if the set value is exceeded
Displays the current power from 0 to 999.
Manual program
4 programs
4 programs
4 programs
Cardio program
Performance program, used to maintain constant performance
The user sets his own program
14
USE
Turn on
Connect the device to the socket, the console will start, and all the data will be displayed for 2 seconds
(Fig. 1).
Fig. 1
Program selection
Use the UP and DOWN buttons to select the manual program (Fig. 2) - beginner (Fig. 3) - advanced
(Fig. 4) - sporty (Fig. 5) - cardio (Fig. 6) - watt (Fig. 7) - user (Fig. 8)
Fig. 3 Fig. 2
Fig. 4 Fig. 5
Fig. 6
15
Fig. 7
Fig. 8
Manual program
Press "Start" on the home page to enter the manual mode and start the program.
Use the "Up" and "Down" buttons to select the manual mode and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to set the time (Fig. 9), distance (Fig. 10), calories (Fig. 11), heart rate (Fig. 12), confirm with "Mode / Enter".
Press "Start / stop" to start the program. Use the "Up" and "Down" buttons to adjust the resistance.
The resistance is displayed in the Watt window. If the resistance is not adjusted for 3 seconds, it switches to the watt display (Fig. 13).
Press "Start / stop" to start or stop the program. Press "Reset" to return to the home page.
Fig. 9
Fig. 11
Fig. 10
Fig. 12
Fig. 13
16
Beginner
Use the "Up" and "Down" buttons to select the beginner and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to select mode 1 - 4 (Fig. 14) and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to set the time.
Press "Start / stop" to start the program. Use the "Up" and "Down" buttons to adjust the resistance.
Press "Start / stop" to start or stop the program. Press "Reset" to return to the main page.
Fig. 14
Advanced
Use the "Up" and "Down" buttons to select advance and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to select mode 1 - 4 (Fig. 15) and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to set the time.
Press "Start / stop" to start the program. Use the "Up" and "Down" buttons to adjust the resistance.
Press "Start / stop" to start or stop the program. Press "Reset" to return to the main page.
Fig. 15
Sporty
Use the "Up" and "Down" buttons to select the sporty and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to select mode 1 - 4 (Fig. 16) and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to set the time.
Press "Start / stop" to start the program. Use the "Up" and "Down" buttons to adjust the resistance.
Press "Start / stop" to start or stop the program. Press "Reset" to return to the main page.
17
Fig. 16
Cardio
Use the "Up" and "Down" buttons to select H.R.C and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to set the age (Fig. 17).
Use the "Up" and "Down" buttons to select 55% (Fig. 18), 75%, 90% or TAG (user setting, original value: 100).
Use the "Up" and "Down" buttons to set the time.
Press "Start / stop" to start or stop the program. Press "Reset" to return to the main page.
Fig. 17 Fig. 18
Watt
Use the "Up" and "Down" buttons to select Watt and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to set the target power (Watt, original value: 120) (Fig. 19).
Use the "Up" and "Down" buttons to set the time.
Press "Start / stop" to start the program. Use the "Up" and "Down" buttons to adjust the Watt value.
Press "Start / stop" to start or stop the program. Press "Reset" to return to the main page.
Fig. 19
User program
Use the "Up" and "Down" buttons to select the user program and confirm with "Mode / Enter".
Use the "Up" and "Down" buttons to select U1 - U4.
18
Use the "Up" and "Down" buttons to set the profile (Fig. 20). The user must set 20 parts, in each of which he must set the resistance. During the setting, the user can exit the setting by pressing the
"Mode / Enter" button for 2 seconds.
Use the "Up" and "Down" buttons to set the time.
Press "Start / stop" to start the program. Use the "Up" and "Down" buttons to adjust the Watt value.
Press "Start / stop" to start or stop the program. Press "Reset" to return to the main page.
Fig. 20
Recovery program
After the exercise, grasp the sensors on the handles and press "Recovery". All functions except time are stopped and the countdown starts from 00:60 to 00:00 (Fig. 21). The display then shows the result from F1 to F6, where F1 is the best result and F6 the worst result (Fig. 22).
Press "Recovery" to return to the menu.
Fig. 21
Body fat
Press "Body fat" to start the program.
Fig. 22
Use the "Up" and "Down" buttons to select U1 - U4.
Use the "Up" and "Down" buttons to set the profile. The user must set the age (Fig. 23, age), height, weight and then the program will start.
The user must hold the sensors on the handles during the test. The display shows "= =" "= =" (Fig. 24) for 8 seconds.
The display shows FAT, then BMI (fig. 25) and FAT% (fig. 26) are displayed for 30 seconds.
Fig. 23
19
Fig. 24
Fig. 25
ERROR MESSAGES
E-1: heart rate not detected
E-4: % of body fat and BMI is below 5 or above 50 (Fig. 27)
Fig. 26
Fig. 27
NOTE:
The device switches to standby mode if it is not used for 4 minutes. Press any button to wake up the device.
If the data is difficult to read or incorrect, unplug and reconnect the device.
USE
Exercise on the exercise bike is based on very simple movements, but you will surely fall in love with them. Thanks to simplicity of the exercise on the exercise bike in can be done by elderly people. Prior to exercise, it is necessary to adjust the height of the saddle. It is important that you sit comfortably.
The bicycle saddle must be set so that you can hold the ergonomically shaped handles when sitting.
You should not have fully extended hands. You can damage your muscles.
To ensure a comfortable and comfortable exercise, put your feet on the pedal. Nowadays, all modern pedals are equipped with straps for fastening and stabilizing of the foot. It is important for your foot to be firmly and safely positioned during exercise.
The basis of exercising on a bicycle is that the legs are moving on a specific elliptical path. This movement is very similar to cycling. When doing exercise on a bicycle, you just sit on the saddle with the right height, keep your feet firmly in the pedals, hold the ergonomically shaped handles and exercise.
It is advisable at the beginning to choose a lower load. If you exercise at regular intervals on an exercise bike, you can gradually increase the load. You can increase the load gradually over a week or two weeks. Selecting a high load during the start of training can lead to rapid fatigue and muscle damage.
When exercising, it's important to choose the right load and the right tempo. Try to keep it throughout the exercise. It is not recommended to choose a high pace right from the start. Increase tempo after about a week of regular exercise. The high pace is not equal to the faster burning of calories. Correct calorie burning is reflected in an appropriate and regular exercise. At the beginning of the exercise, the
20
number of burned calories may seem low, but regular and appropriate exercise is the key to achieving the best results.
Exercise on the exercise bike also leads to the formation of muscles. It is mainly used to strengthen the thigh and calf muscles. While exercising on a bicycle, you also move your buttocks.
If you want to exercise right, you should not forget to breathe properly. Proper and regular breathing is recommended in any exercise. It is important to keep regular deep inhales and exhales. Regular and proper breathing during exercises on the exercise bike involves intense exercise of the abdominal muscles. It is advisable to practice 30-35 after consuming food. Failure to do so may result in less calories burned, and in older age even lead to digestive problems.
For best results, you should also consider your diet. It is recommended to start a day of eating sweet food and pastries or muesli with milk. For lunch is recommended to eat a caloric richer meal. Do not forget about the soup. In the evening, light meals are recommended. If you want to improve your health, it's not just a regular exercise but a whole diet.
Bicycle exercise is an effective exercise for all busy people. Exercise on the exercise bike is effective in strengthening muscles, especially thighs, calves and buttocks. Regular exercise can lead to a slimmer figure. Exercise is recommended not only as a winter training for cyclists but also for people who want to burn excess calories. Regular breathing, regular exercise, reasonable tempo, and balanced diet can lead to your desired results.
EXERCISING INSTRUCTIONS
A successful workout begins with warm-up exercises and ends with cool-down (relaxing) exercises.
The warm-up exercises should make your body ready for the main workout. The cool-down phase should protect your muscles from injuries and cramps. Do warm-up and cool-down exercises as shown in the chart below.
Touching your toes
Slowly bend your back from hips. Keep your back and arms relaxed while stretching downwards to your toes. Do it as far as you are able and hold the position for 15 seconds. Bend your knees slightly.
Upper thigh
Lean against a wall with one hand. Reach down and behind you. Lift up your right or left foot to your buttock as high as possible. Keep for
30 seconds and repeat twice for each leg.
Hamstring stretched
Sit and outstretch your right leg. Rest the sole of your left foot against the inside of your right tight. Stretch out your right arm along your right leg as far as you can. Hold for 15 seconds and relax. Repeat all with your left leg and left arm.
Inside upper thigh
Sit on the floor and place your feet together. Knees are pointed outwards. Pull your feet as close as possible to your groin. Press your knees carefully downwards. Keep this position for 30-40 seconds if possible.
Calves and Achilles tendon
Lean against a wall with your left leg in front of the right one and your arms forward. Stretch out your right leg and keep your left foot on the floor. Bend your left leg and lean forwards by moving your right hip in the direction of the wall. Hold for 30-40 seconds. Keep your leg stretched and repeat exercising with other leg.
21
CORRECT BODY POSTURE
When training, keep your body upright, or you can learn your hand on your forearms. During pedaling, you should not have your legs fully extended. Your knees should be slightly bent when fully pressing down the pedal. Keep your head straight with your spine to minimize the pain of the cervical muscles and upper back muscles. Always exercise fluently and rhythmically.
MAINTENANCE
•
When assembling, tighten all screws and adjust the bike to the horizontal position.
•
Check the screws after 10 hours of use.
•
Wipe the sweat after the exercise. Clean the device with a cloth and gentle cleanser. Do not use solvents or aggressive cleaners on the plastic parts.
•
When noise is increased, it is necessary to check that all joints are tightened properly.
•
Place the product in a clean, ventilated and dry room.
•
Do not expose the device to direct sunlight.
STORAGE
Keep the exercise bike in a clean and dry environment. Make sure the power switch is turned off and the exercise bike is not plugged into the power socket.
IMPORTANT NOTICE
•
This exercise bike comes with standard safety regulations and is suitable for home use use.
Any other use is prohibited and may be dangerous to users. We are not responsible for any injury caused by improper and forbidden use of the machine.
•
Consult your doctor before starting training on the exercise bike. Your doctor should evaluate whether you are physically fit to use the machine and how much effort you are able to undergo. Incorrect exercise or switching of the body can harm your health.
•
Carefully read the following tips and exercises. If you experience pain, nausea, breathing, or other health problems during exercise, immediately stop the exercise. If the pain persists, contact your doctor immediately.
•
This exercise bike is not suitable for medical purpose. It can also not be used for healing purposes.
•
The heart rate monitor is not a medical device. It provides only approximate information about your average heart rate, and any suggested pulse rate is not medically binding. Accumulated data may not always be accurate regarding uncontrollable human and environmental factors.
ENVIRONMENT PROTECTION
After the product lifespan expired or if the possible repairing is uneconomic, dispose it according to the local laws and environmentally friendly in the nearest scrapyard.
By proper disposal you will protect the environment and natural sources. Moreover, you can help protect human health. If you are not sure in correct disposing, ask local authorities to avoid law violation or sanctions.
Don’t put the batteries among house waste but hand them in to the recycling place.
22
DIAGRAM
23
PARTS LIST
No.
1 Main frame
Name
2 Front stabilizer
3 Rear stabilizer
4 Seat post
5 Seat
6 Middle post
7 Handlebars
8 Console
9 Console communication cable
10 Motor communication cable
11 Pulse communication cable
12 Console communication cable
13 Front handlebar cover
14 Side handlebar cover – L
15 Side handlebar cover – R
16 Seat cover – L
17 Seat cover – R
18 Pedal – L
19 Pedal – R
20 Bottle handlebar
21 Knob
22 Handlebar clamping ring
23 Seat knob
24 Screw M5 ×10
25 Sleeve Φ25×Φ19×60
26 Screw M10×70×20
27 Spring washer Φ10
28 Arc washer
29 Screw M4×6
30 Allen screw M8×20
31 Allen screw M12*60
32 Screw
M4×16
33 Closing part of the seat
34 Crank cover
35 Screw
2
6
6
5
1
1
1
1
1
4
1
1
1
1
1
1
2
1
1
1
1
1
Qty. No.
1 36 Crank – L
1 37 Crank – R
1
1
38 Strap
1
1
Name
39 Foam roller
40 Motor cover – left
41 Motor cover – right
42
43
44
45
Brake cable
Power adapter 240 V
Magnetic sensor
Power communication cable
46 Magnetic motor
47 End cap
48 Support feet
49 Allen screw Φ8×33×M6×15
50 Transport wheels Φ54.5×23.5
51 Allen screw M6×15
52 Bearing 6203-2RS
53 Nut M5
54 Screw M5x60
55 Screw S T4×12
56 Seat post grommet
57
58
Crank axis
Belt
59 Nut M8
1
4
4
4
60 Seat adjustment
61 Shaft retaining ring
Φ17
62 Shaft retaining ring
Φ12
63 Shaft retaining ring
Φ10
64 Tensioning wheel
65 Tensioning spring
66 Brake tension spring
67 Magnet
1
2
2
68 Magnetic control axis
69 Ball-bearing 6300-2RS
70 Washer
24
2
3
1
1
1
1
1
1
10
2
2
4
4
1
1
1
1
1
1
2
1
Qty.
1
1
1
1
1
1
1
10
2
1
5
3
1
2
71 Ball-bearing 6003-2RS
72 One-way bearing
73 Small pulley
74 Ball-bearing
75 Flywheel axis
76 Flywheel
77 Square cover
78 Pulse handle
79 Screw
ST4×20
80 Round end cap
2
2
2
1
1
1
1
1
1
1
81 Screw ST4x16
82 Magnet
83 Screw
84 Fixed tension wheel
85 Magnet
86 Plastic screw
87 Screw ST4×12
88 Hole plug
89 Spring washer
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS
General Conditions of Warranty and Definition of Terms
All Warranty Conditions stated hereunder determine Warranty Coverage and Warranty Claim
Procedure. Conditions of Warranty and Warranty Claims are governed by Act No. 89/2012 Coll. Civil
Code, and Act No. 634/1992 Coll., Consumer Protection, as amended, also in cases that are not specified by these Warranty rules.
The seller is SEVEN SPORT s.r.o. with its registered office in Borivojova Street 35/878, Prague
13000, Company Registration Number: 26847264, registered in the Trade Register at Regional Court in Prague, Section C, Insert No. 116888.
According to valid legal regulations it depends whether the Buyer is the End Customer or not.
“The Buyer who is the End Customer” or simply the “End Customer” is the legal entity that does not conclude and execute the Contract in order to run or promote his own trade or business activities.
“The Buyer who is not the End Customer” is a Businessman that buys Goods or uses services for the purpose of using the Goods or services for his own business activities. The Buyer conforms to the
General Purchase Agreement and business conditions.
These Conditions of Warranty and Warranty Claims are an integral part of every Purchase Agreement made between the Seller and the Buyer. All Warranty Conditions are valid and binding, unless otherwise specified in the Purchase Agreement, in the Amendment to this Contract or in another written agreement.
Warranty Conditions
Warranty Period
The Seller provides the Buyer a 24 months Warranty for Goods Quality, unless otherwise specified in the Certificate of Warranty, Invoice, Bill of Delivery or other documents related to the Goods. The legal warranty period provided to the Consumer is not affected.
By the Warranty for Goods Quality, the Seller guarantees that the delivered Goods shall be, for a certain period of time, suitable for regular or contracted use, and that the Goods shall maintain its regular or contracted features.
The Warranty does not cover defects resulting from (if applicable):
• User’s fault, i.e. product damage caused by unqualified repair work, improper assembly, insufficient insertion of seat post into frame, insufficient tightening of pedals and cranks
•
Improper maintenance
•
Mechanical damages
•
Regular use (e.g. wearing out of rubber and plastic parts, moving mechanisms, joints etc.)
25
2
4
1
6
4
1
1
8
1
•
Unavoidable event, natural disaster
•
Adjustments made by unqualified person
•
Improper maintenance, improper placement, damages caused by low or high temperature, water, inappropriate pressure, shocks, intentional changes in design or construction etc.
Warranty Claim Procedure
The Buyer is obliged to check the Goods delivered by the Seller immediately after taking the responsibility for the Goods and its damages, i.e. immediately after its delivery. The Buyer must check the Goods so that he discovers all the defects that can be discovered by such check.
When making a Warranty Claim the Buyer is obliged, on request of the Seller, to prove the purchase and validity of the claim by the Invoice or Bill of Delivery that includes the product’s serial number, or eventually by the documents without the serial number. If the Buyer does not prove the validity of the
Warranty Claim by these documents, the Seller has the right to reject the Warranty Claim.
If the Buyer gives notice of a defect that is not covered by the Warranty (e.g. in the case that the
Warranty Conditions were not fulfilled or in the case of reporting the defect by mistake etc.), the Seller is eligible to require a compensation for all the costs arising from the repair. The cost shall be calculated according to the valid price list of services and transport costs.
If the Seller finds out (by testing) that the product is not damaged, the Warranty Claim is not accepted.
The Seller reserves the right to claim a compensation for costs arising from the false Warranty Claim.
In case the Buyer makes a claim about the Goods that is legally covered by the Warranty provided by the Seller, the Seller shall fix the reported defects by means of repair or by the exchange of the damaged part or product for a new one. Based on the agreement of the Buyer, the Seller has the right to exchange the defected Goods for a fully compatible Goods of the same or better technical characteristics. The Seller is entitled to choose the form of the Warranty Claim Procedures described in this paragraph.
The Seller shall settle the Warranty Claim within 30 days after the delivery of the defective Goods, unless a longer period has been agreed upon. The day when the repaired or exchanged Goods is handed over to the Buyer is considered to be the day of the Warranty Claim settlement. When the
Seller is not able to settle the Warranty Claim within the agreed period due to the specific nature of the
Goods defect, he and the Buyer shall make an agreement about an alternative solution. In case such agreement is not made, the Seller is obliged to provide the Buyer with a financial compensation in the form of a refund.
26
27
advertisement