advertisement
Acer Projector
H8550BD/V7500/HV750/V240/
HT-820 Series
User's Guide
Copyright © 2015. Acer Incorporated.
All Rights Reserved.
Acer Projector User's Guide
Original Issue: 05/2015
Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concerning your unit should include the serial number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated.
Model number: _________________________________
Serial number: __________________________________
Date of purchase: _______________________________
Place of purchase: ______________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product names or trademarks are used herein for identification purposes only and belong to their respective companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
Information for your safety and comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the external power supply unit:
• Install the power supply unit before connecting the power cord to the AC power outlet.
• Unplug the power cord before removing the power supply unit from the projector.
• If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet.
iii
Warnings!
• Do not use this product near water.
• Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged.
• Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
iv
• To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface.
• Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp.
Using electrical power
• This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
• Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.
• If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
• Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip's input rating.
• This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
• Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
• the power cord or plug is damaged, cut or frayed
• liquid was spilled into the product
• the product was exposed to rain or water
• the product has been dropped or the case has been damaged
• the product exhibits a distinct change in performance, indicating a need for service
• the product does not operate normally after following the operating instructions
v
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Additional safety information
• Do not look into the projector's lens when the lamp is on. The bright may hurt your eyes.
• Turn on the projector first and then signal sources
• Do not place the product in following environments:
•
•
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the life span and darkening the image.
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
• Locations where the altitudes are higher than 10000 feet.
• Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It
vi
might cause fire or electric shock. In this case, unplug immediately and contact your dealer.
• Do not keep using this product to break or drop it. In this case contact your dealer for inspection.
• Do not face the projector lens to the sun. It can lead to fire.
• When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power.
• Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to wait for the fan to turn off before turning main power off.
• Do not touch air outlet grille and bottom plate which becomes hot.
• Clean the air filter frequently if have. The temperature inside may rise and cause damage when the filter/ventilation slots clogged with dirt or dust.
• Do not look into the air outlet grille when projector is operating. It may hurt your eyes.
• Always open the lens shutter or remove the lens cap when the projector is on.
• Do not block the projector lens with any object when the projector is under operation as this could cause the object to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press HIDE on the remote control.
• The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
• Do not operate lamps beyond the rated lamp life. It could cause it to break on rare occasions.
• Never replace the lamp assembly or any electronic components unless the projector is unplugged.
• The product will detect the life of the lamp itself. Please be sure to change the lamp when is showing warning message.
• When changing the lamp, please allow unit to cool down, and follow all changing instructions.
• Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
• Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you. The only user serviceable part is the lamp which has its own removable cover. Refer servicing only to suitable qualified professional service personnel.
• Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage.
• This product is capable of displaying inverted images for ceiling mount installation. Only use acer ceiling mount kit for mounting the projector and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
Increase the volume gradually until you can hear clearly and comfortably.
•
Do not increase the volume level after your ears have adjusted.
•
Do not listen to music at high volumes for extended periods.
•
Do not increase the volume to block out noisy surroundings.
•
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury,
Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal information, check www.lamprecycle.org
viii
First things first
Usage Notes
Do:
• Turn off the product before cleaning.
• Use a soft cloth moistened with mild detergent to clean the display housing.
• Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Don't:
• Block the slots and openings on the unit provided for ventilation.
• Use abrasive cleaners, waxes or solvents to clean the unit.
• Use under the following conditions:
•
In extremely hot, cold or humid environments.
•
In areas susceptible to excessive dust and dirt.
•
Near any appliance that generates a strong magnetic field.
•
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user's guide to maximize the life of your unit.
Warning:
• Do not look into the projector's lens when the lamp is on. The bright light may hurt your eyes.
• To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
•
Please do not open or disassemble the product as this may cause electric shock.
•
When changing the lamp, please allow unit to cool down, and follow all changing instructions.
• This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages.
•
Reset the "Lamp Hour Reset" function from the Onscreen display "Management" menu after replacing the lamp module.
•
When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting power.
• Turn on the projector first and then the signal sources.
• Do not use lens cap when projector is in operation.
• When the lamp reaches the end of its life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under
Information for your safety and comfort
First things first
Usage Notes
Precautions
Introduction
Product Features
Package Overview
Projector Overview
Projector Outlook
Control Panel
Remote Control Layout
MHL (Mobile High-Definition Link) Control
Getting Started
Connecting the Projector
Turning the Projector On/Off
Turning on the Projector
Turning the projector off
Adjusting the Projected Image
Adjusting the Height of Projected Image
How to optimize image size and distance
How to get a preferred image size by adjusting distance and zoom
How to get a preferred image position by adjusting lens shift
User Controls
Installation menu
Onscreen Display (OSD) Menus
Color
Image
Setting
Management
Audio
3D
9
9
11
11
12
13
13
14
1
1
2
5
6
3
3
8
iii
viii viii viii
15
16
21
23
25
27
28
29
18
18
20
Language
Appendices
Troubleshooting
LED & Alarm Definition Listing
How to install cable management
Cleaning and replacing the dust filters
Replacing the Lamp
Ceiling Mount Installation
Specifications
Compatibility modes
Regulations and safety notices
29
30
30
40
43
45
34
35
37
38
50
Introduction
Product Features
This product is a single-chip DLP
®
projector. Outstanding features include:
• DLP ® technology
• 1920x1080 1080p resolution
Full/4:3/16:9/L.Box aspect ratio supported
• Enables projecting 3D content via DLP Link Technology: Blue-Ray 3D supported and nVidia 3DTV Play Ready
• Acer ColorBoost technology delivers nature’s true colors for vivid, life-like images
• High brightness and contrast ratio
• Acer LumiSense+ technology can intelligently optimizes the brightness and color saturation of projected image based on actual ambient light.
• Versatile display modes (Bright, Standard, Movie, Dark Cinema, Game,
Sport, User) enable optimum performance in any situation
• NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
• Lower power consumption and economy (ECO) mode extend lamp life
• Acer EcoProjeciton Technology delivers Intelligent power management approach and physical efficiency improvement
• Equipped with HDMI ™ & MHL connection supporting HDCP
• Support HDMI CEC function
• Advanced digital keystone and 4-corner correction optimizes presentations
• Smart detection delivers quick, intelligent source detection
• Multi-language onscreen display (OSD) menus
• Manual focus projection lens zooms up to 1.36x
• 2x digital zoom and pan function
• Microsoft ® Windows ® 2000, XP, Vista
Macintosh
®
OS compliant
® , Windows 7, Windows 8,
• Support MHL V2.0 signal display
• Support LumiSense+
• Built-in One 10 Watts speaker
• Manual lens vertical shift adjustment
• Cable management
1
Note: Functions vary depending on model definition.
2
Package Overview
This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable
HDMI extension cable Security card User’s guide
Quick start guide Carrying case
(option)
Dust filters
(option)
Remote control
Dongle rubber
2 x Batteries
(option)
Cable management cover
WirelessHD-Kit
(option)
MHL
H DMI
DC 5V IN
WirelessCAST
(option)
Projector Overview
Projector Outlook
Front / upper side
9
8 7
# Description
1 Ambient light sensor
2 Remote control receiver
3 Lens Cap
4 Focus ring
5 Lens shift control ring
6 Zoom lever
6
5
4
1
2
3
11
10
# Description
7 Power button
8 Control panel
9 Lamp cover
10 Tilt adjusting wheels
11 Projection lens
3
4
Right / Rear side
1 2 3 4 5
DC 5V OUT DC 12V OUT
VIDEO Pr/Cr
1/MHL
VGA IN
USB CTRL
AUDIO IN Pb/Cb
2
AUDIO OUT Y RS232
6 7 8 9 10 11 12 13 14
6
7
3
4
1
2
#
5
Description
Composite video input connector
5V DC output connector
12V DC output connector
PC analog signal/HDTV/component video input connector (VGA, VGA IN,
VGA IN 1, VGA IN 2)
HDMI/MHL connector (HDMI/MHL,
HDMI 1/MHL)
Security bar
Audio in connector
# Description
8
9
Audio out connector
YPbPr/YCbCr input connector
10 RS232 connector
11
Mini USB Ctrl connector (for firmware upgrade and USB display)
12
HDMI 2 connector
13 Power socket
14 Kensington™ lock port
Note: Functions vary depending on model definition.
Control Panel
1 8 2 3
4
9
5
6
10
7
5
6
2
3
1
# Icon
4
7
8
9
10
POWER
Function
LAMP
TEMP
RESYNC
SOURCE
POWER
Description
Power Indicator LED
Lamp Indicator LED
Temp Indicator LED
Automatically synchronizes the projector to the input source.
Changes the active source.
See the contents in "Turning the Projector
MODE
MENU
Press "MODE" to select the display mode from Bright, Standard, Movie, Dark
Cinema, Game, Sport and User.
• Press "MENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu.
• Confirm your selection of items.
Four directional select keys
Use to select items or make adjustments to your selection.
Keystone Adjusts the image to compensate for distortion caused by tilting the projector.
Note: Functions vary depending on model definition.
5
6
Remote Control Layout
Model No:E-26281
9
11
2
5
7
13
MEDIA
SETUP
ZOOM
MODE
RATIO
SOURCE
HIDE
FREEZE
1
3
4
6
8
10
12
25
MEDIA
SETUP
ZOOM
MODE
SOURCE
HIDE
FREEZE
26
Model No:E-26171
15
17
19
21
23
14
16
18
20
22
24
E-26110
MC.JG811.009
LASER MODULE : M-5.2-6.5x10-5.5x5.5
BONTECH ELECTRONICS(K.S) CO ., LTD .
No. 2018, Zhonghuayuan west road,
Yushan town,Kunshan city, China
MC.JK211.004
6
7
8
9
10
11
3
4
5
1
# Icon Function
Infrared transmitter
2 POWER
12
13
Description
Sends signals to the projector.
Refer to the "Turning the Projector On/Off" section.
3D Press "3D" to select 3D models.
SOURCE
MODE
HIDE
FREEZE
MENU
Changes the active source.
Press "MODE" to select the display mode from Bright,
Standard, Movie, Dark Cinema, Game, Sport and User.
Momentarily turns off the video. Press "HIDE" to hide the image, press again to display the image.
MEDIA_SETUP No function.
RATIO To choose the desired aspect ratio.
ZOOM Zooms the projector display in or out.
To pause the screen image.
KEYSTONE
• Press "MENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu.
• Confirm your selection of items.
Adjusts the image to compensate for distortion caused by tilting the projector.
Four directional select keys
Use up, down, left, right buttons to select items or make adjustments to your selection.
7
20
21
22
23
24
25
26
15
16
18
19
# Icon Function
14
17
Pre./Rewind No function.
Description
Enter/ Play/
Pause
Back/Stop
No function.
No function.
Next/Fast forward
KeyPad 0~9
PgUp/PgDn
No function.
Press "0~9" to input a password in the "Security" OSD.
For computer mode only. Use this button to select the next or previous page. This function is only available when USB Ctrl connector (mini type B) is connected to a computer via a USB cable.
COMPONENT Press "COMPONENT" to change source to Component video.
This connection supports YPbPr (480p/576p/720p/1080i) and
YCbCr (480i/576i).
VIDEO To change source to COMPOSITE VIDEO.
VGA Press "VGA" to change source to the VGA connector. This connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
No function.
S-VIDEO
SD/USB A
USB B
No function.
For USB control and firmware upgrade.
HDMI/DVI
LAN/WiFi
To change source to HDMI/MHL. (no DVI function)
No function.
Laser pointer Aim the remote at the viewing screen.
Laser button Aim the remote at the viewing screen, press and hold this button to activate the laser pointer.
This function is not supported in Japanese market.
Note: Functions vary depending on model definition.
8
MHL (Mobile High-Definition Link) Control
2
1
MEDIA
SETUP
ZOOM
MODE
SOURCE
HIDE
FREEZE
3
4
6 5
8 7
2
3
4
7
8
5
6
1
# Icon Component
MODE
Description
•
Press "MODE" button for one second to activate the
MHL Control Mode.
•
To exit, press the "MODE" button again.
SOURCE
MENU
Press the "SOURCE" button to toggle between Navigation or Numeric mode.
Press to launch the root memu.
(only for Navigation mode)
Direction Keys Use up, down, left, right buttons to select items or make adjustments to your selection.
(only for Navigation mode)
Select To select the file. (only for Navigation mode)
Exit
PgUp/PgDn
KeyPad 0~9
To exit the file. (only for Navigation mode)
Use the button to select the next or previous page. (only for Navigation mode)
Number buttons. (only for Numeric mode)
Note: Functions vary depending on model definition.
Getting Started
Connecting the Projector
DVD player,
Set-top Box,
HDTV receiever
R B G
Power Bank
Smart Phone
Video output
9 9
D-Sub
4
2
R B G
5
6
8 3
D-Sub
HDTV adapter
HDMI HDMI HDMI
W R
11
Y
10
DC 5V OUT DC 12V OUT
VIDEO Pr/Cr
1/MHL
VGA IN
USB CTRL
USB
AUDIO IN Pb/Cb
2
AUDIO OUT Y RS232
13
R G B
HDMI
USB
11
7
DVD player
Acer Dongle
DVD player
USB
MHL
1
5
R W 4
11
R G B
12
DVD player,
Set-top Box,
HDTV receiever
RS232
RS232
9
10
4
5
2
3
6
1
#
7
Description
Power cord
VGA cable
VGA to component/HDTV adapter
3 RCA component cable
HDMI cable
HDMI extension cable (for wireless dongle)
MHL cable (MicroUSB to HDMI)
#
8 12V DC cable
Description
9 USB cable for charging device
10 Composite video cable
11 Audio cable Jack/RCA
12 RS232 cable
13 USB cable
Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector.
Note: Functions vary depending on model definition.
Note: USB cable needs powered extender if the length is over 5 m.
Note: Some smartphones require a converter (supplied by smartphone maker) to enable the MHL function.
Note: Before connecting the projector, remove the cable management, refer to "Removing the cable management" section.
Note: DC 12V out connector support 12V/100mA power for screen control only.
Note: USB DC 5V out connector support 5V/1.5A power output for power bank charging only when MHL source is not detected.
11
Turning the Projector On/Off
Turning on the Projector
1 Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
2 Turn on the projector by pressing "Power" button on the control panel or remote control, and the Power indicator LED will turn blue.
3 Turn on your source (computer, notebook, video player ,etc.). The projector will detect your source automatically.
•
•
If the screen displays "Lock" and "Source" icons, it means the projector is locked onto a specific source type and there is no such type of input signal detected.
If the screen displays "No Signal", please make sure the signal cables are securely connected.
• If you connect to multiple sources at the same time, use the "Source" button on either control panel or the remote control or direct source key on the remote control to switch between inputs.
Power button
12
Turning the projector off
1 To turn the projector off, press and hold the power button. This message appears: "Please press the power button again to complete the shutdown process." Press the power button again.
2 The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly. (only supported under "Instant
Resume" mode)
3 As long as the power cord remains plugged in, you can press the power button to turn the projector immediately back on anytime during the 2minute shutdown process. (only supported under "Instant Resume" mode)
4 Once the system has finished cooling, the LED power indicator will stop blinking and turn solid red to indicate standby mode.
5 It is now safe to unplug the power cord.
•
•
Warning indicators:
"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically shut down, and the LED temp indicator will turn solid red. Contact your local dealer or service center.
"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will automatically turn off, the projector will automatically shut down, and the LED temp indicator will blink. Contact your local dealer or service center.
Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or service center.
Note: Functions vary depending on model definition.
13
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise/lower the image:
Use Tilt adjusting wheel to fine-tune the display angle.
Tilt adjusting wheel
14
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen.
• 1080p series
If the projector is 3 m from the screen, good image quality is possible for image sizes between 93" and 127".
Note: Remind as below figure, the space of 183 cm height is required when located at 3 m distance.
Max sc reen siz e
Min scr een siz e
B
127"
Height:
135 cm
C
Height: 183 cm from base to top of image
5.5
6
6.5
7.1
3
3.5
4
4.5
5
171
187
202
221
93
109
125
140
156
Zoom Ratio: 1.36x
207 x 116
241 x 136
276 x 155
310 x 174
345 x 194
379 x 213
414 x 233
448 x 252
489 x 275
A
3 m
Desired Distance
1
1.3
1.5
2
2.5
31
40
47
62
78
Screen size
Desired
Distance
(m)
<A>
Diagonal
(inch)
<B>
(Min zoom)
W (cm) x H
(cm)
69 x 39
90 x 50
103 x 58
138 x 78
172 x 97
Top
From base to top of image
(cm)
<C>
45
58
67
90
112
247
270
292
319
135
157
180
202
225
<B>
Screen size
(Max zoom)
Diagonal
(inch)
W (cm) x H
(cm)
Top
From base to top of image (cm)
<C>
127
148
169
190
211
42
55
63
85
106
233
254
275
300
94 x 53
122 x 68
140 x 79
187 x 105
234 x 132
281 x 158
328 x 184
375 x 211
421 x 237
468 x 263
515 x 290
562 x 316
609 x 342
665 x 374
183
214
244
275
305
61
70
92
122
153
336
367
397
434
15
How to get a preferred image size by adjusting distance and zoom
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring.
• 1080p series
To obtain an image size of 60" set the projector at a distance 1.4 m and 1.9 m from the screen.
A
60"
Desired image size from base to top of image
1.9 m
C
Desired Image Size
Diagonal (inch)
<A>
31
40
50
60
70
80
90
100
120
150
180
200
250
300
Zoom Ratio: 1.36x
W (cm) x H (cm)
69 x 39
89 x 50
111 x 62
133 x 75
155 x 87
177 x 100
199 x 112
221 x 125
266 x 149
332 x 187
398 x 224
443 x 249
553 x 311
664 x 374
1.4 m
B
Desired Distance
2.1
2.4
2.8
3.5
4.3
0.9
1.2
1.4
1.7
1.9
4.7
5.9
7.1
Distance (m)
Max zoom
<B>
Min zoom
<C>
2.9
3.2
3.9
4.8
5.8
6.4
8.0
1.0
1.3
1.6
1.9
2.2
2.6
Top (cm)
From base to top of image
<D>
45
58
72
87
101
116
130
144
173
217
260
289
361
433
16
How to get a preferred image position by adjusting lens shift
The projector is equipped with lens shift for adjusting the position of projected image up and down without requiring you to physically move the projector.
Vertical Lens
Shift ring
Note: The figures shown in this section are for reference only not approximate value. The figures between units can be different due to assembly tolerance.
17
The vertical image height can be adjusted between -6% and 21% of the image height. (The minimum vertical image offset is fixed at 5% of the image height above the centre of the projector lens.)
H
Offset max=V x 21%
V
V
Offset min=V x -6%
18
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message "No signal input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more .
1 Turn on the projector by pressing "Power" button on the control pad.
2 Press the "MENU" button on the remote control to launch the OSD for projector installation and maintenance.
3 The background pattern acts as a guide to adjusting the calibration and alignment settings, such as screen size and distance, focus and more .
4 The Installation menu includes the following options:
•Projection method
•Projection Mode
•Projection Location
•Auto Keystone settings
•Manual Keystone settings
•H. Keystone
•V. Keystone
•LAN/WiFi
•LAN
•LAN IP/Mask
•Wireless HD dongle settings
•Language settings
•DC 5V Out (Standby)
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right arrow keys to adjust selected option settings, and the right arrow key to enter a submenu for feature setting. The new settings will be saved automatically upon exiting the menu.
5 Push the MENU button anytime to exit the menu and return to the Acer welcome screen.
19
Note: Functions vary depending on model definition.
20
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings.
Using the OSD menus
• To open the OSD menu, press "MENU" on the remote control or control panel.
• When the OSD is displayed, use the main menu. After selecting the desired main menu item, press submenu for feature setting.
keys to select any item in the
to enter
• Use the keys to select the desired item and adjust the settings by using the keys.
• Select the next item to be adjusted in the submenu and adjust as described above.
• Press "MENU" on the remote control or control panel, the screen will return to the main menu.
• To exit OSD, press "MENU" on the remote control or control panel. The
OSD menu will close and the projector will automatically save the new settings.
Main menu
Setting
Sub menu
Note: Some of the following OSD settings may not be available. Please refer to the actual OSD of your projector.
Note: Functions vary depending on model definition.
Color
LumiSense
+
Display Mode
Wall color
Brightness
Contrast
Saturation
Tint
The light sensor of LumiSense+ technology can intelligently optimize the brightness and color saturation of projected image based on actual ambient light. The feature greatly enhances dark detail visibility and color saturation.
•
Off: For normal mode. (ambient light sensor is off)
•
Auto Bright: Light sensor is on to automatically detect ambient light and optimize the brightness and color saturation of projected image.
•
Dynamic Black:automatically optimize the display of dark movie scenes enabling them to be shown in incredible detail.
There are many factory presets optimized for various types of images.
•
Bright: For brightness optimization.
• sRGB: standard RGB color space.
•
Game: For game content.
•
Movie: For brighter and general movie/video/photo playing.
•
Dark Cinema: For dark movie content.
•
Sport: For sport picture.
•
User: Memorize user's settings.
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone.
Adjust the brightness of the image.
•
Press to darken the image.
•
Press to lighten the image.
"Contrast" controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
•
Press to decrease the contrast.
•
Press to increase the contrast.
Adjusts a video image from black and white to fully saturated color.
• Press to decrease the amount of color in the image.
•
Press to increase the amount of color in the image.
Adjusts the color balance of red and green.
•
Press to increase the amount of green in the image.
•
Press to increase the amount of red in the image.
21
22
Color
Temperature
Gamma
Advanced
Mode
Use this function to choose CT1, CT2 (Native), CT3, User mode.
R Gain
Adjusts the red gain for color temperature optimization.
G Gain
Adjusts the green gain for color temperature optimization.
B Gain
Adjusts the blue gain for color temperature optimization.
R Bias
Adjusts the red bias for color temperature optimization.
G Bias
Adjusts the green bias for color temperature optimization.
B Bias
Adjusts the blue bias for color temperature optimization.
Effects the representation of dark scenery. With greater gamma value, dark scenery looks brighter.
Ind. Color Management
Adjusts the red, green, blue, cyan, yellow and magenta colors.
Ind. Hue
Adjusts the color balance of red and green.
Ind. Saturation
Adjusts the selected color to be less or more saturated color.
Ind. Gain
Adjusts the selected color's contrast.
Brilliant Color
Produces an expanded on-screen color spectrum that delivers enhanced color saturation for bright, true-to-life images.
White Peaking
Increases the brightness of whites that are near 100%. (video sources only)
Film Mode
Sets the image optimized to 24-frame True Film mode.
Noise Reduction
Adjusts signal noise reduction."0" means the noise reduction is off,
">0" increase noise reduction.
Black Extension
This ensures optimum black level for each analog source.
Note: "Saturation" and "Tint" functions are not supported under computer or HDMI mode.
Note: Functions vary depending on model definition.
Image
Projection Mode
•
•
Front: The factory default setting.
Rear: Reverses the image so you can project from behind a translucent screen.
Projection Location
Aspect Ratio
H./V. Keystone
4 Corner
Correction
•
Auto: Automatically adjusts projection location of image.
•
Desktop
•
Ceiling: Turns the image upside down for ceiling-mounted projection.
Use this function to choose your desired aspect ratio.
•
Auto: Keep the image with original width-higth ratio and maxi mize the image to fit native horizontal or vertical pixels.
•
Full: Resize image to fit full screen by width (1280 pixels) and height (800 pixels).
•
4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio.
•
16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:9 ratio.
•
L.Box: Keep original signal aspect ratio and zoom in by 1.333 times.
Auto V. Keystone
Automatically adjusts vertical image.
H. Keystone
Press the or button to adjust image distortion horizontally and makes a squarer image.
V. Keystone
Press the or button to adjust image distortion vertically and makes a squarer image.
Manually adjusts the shape and size of an image that is unevenly rectangular on all sides. Press "MODE" repeatedly to select the corner that you wish to adjust. Press four directional selection keys to adjust the image shape.
23
Sharpness
<Note> The function is unavailable when H./ V. Keystone is adjusted.
Adjusts the sharpness of the image.
•
Press to decrease the sharpness.
•
Press to increase the sharpness.
24
H. Position
(Horizontal position)
• Press to move the image left.
• Press to move the image right.
V. Position
(Vertical position)
• Press to move the image down.
•
Press to move the image up.
Frequency
Tracking
"Frequency" changes the projector's refresh rate to match the frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments.
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to correct it.
HDMI Color Range Adjust the color range of the HDMI image data to correct color display error.
•
Auto: Automatically adjust by information from player.
•
Limited Range: Prosess the input image as limited color range data.
•
Full Range: Prosess the input image as full color range data.
HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen.
•
Auto: Automatically adjust by information from player.
•
Underscan: Always no overscan on HDMI image.
•
Overscan: Always keep overscan on HDMI image.
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions are not supported under HDMI or Video mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only supported under HDMI mode.
Note: Functions vary depending on model definition.
Setting
Startup Screen
Screen Capture
Source Lock
Use this function to select your desired startup screen. If you change the setting, the changes will take effect when you exit the
OSD menu.
• Acer: The default startup screen of your Acer projector.
• User: Use memorize picture from "Screen Capture" function.
Use this function to customize the startup screen. To capture the image that you want to use as the startup screen, follow the instructions below.
Notice:
Before proceeding with the following steps, make sure that the
"Keystone" is set to the default value 0 and the aspect ratio is set to 4:3. For details, refer to the "Image" section.
• Change the "Startup Screen" from the default setting "Acer" to "User".
• Press "Screen Capture" to customize the startup screen.
• A dialog box appears to confirm the action. Choose "Yes" to use the current image as your customized startup screen. The capture range is the red rectangular area. Choose "No" to cancel the screen capture and exit the onscreen display (OSD).
• A message appears, stating that the screen capture is in progress.
• When the screen capture is finished, the message disappears and the original display is shown.
• The customized startup screen, as shown below, takes effect when there is a new input signal or when you restart the projector.
When Source Lock is turned "Off", the projector will search for other signals if the current input signal is lost. When Source Lock is turned "On", it will "lock" the current source channel unless you press "Source" button on the remote control for the next channel.
Closed Caption Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only available when a composite video or S-Video input signal is selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not available when the aspect ratio is "16:9" or "Auto" .
Auto Screen
DC 5V Out (Standby) Default is "Off". Choose "On" to enable DV 5V OUT connection during standby mode.
HDMI CEC
Reset
Default is "On", the down/up move of electronic screen will be related with power on/off of the projector.
Default is "Off". Select “On” to enable HDMI CEC function.
•
Press the button and choose "Yes" to return the parameters on all menus to the factory default settings.
25
26
Security Security
This projector provides a useful security function for the administrator to manage usage of the projector .
Press to change the "Security" setting. If the security function is enabled, your must enter the "Administrator Password" first before changing the security settings.
•
Select "On" to enable the security function. The user has to enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set timeout function.
•
Press or to select the timeout interval.
•
The range is from 10 minute to 990 minutes.
•
When the time is up, the projector will prompt the user to enter the password again.
•
The factory default setting of "Timeout(Min.)" is "Off".
•
Once the security function is enabled, the projector will request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be accepted for this dialogue.
User Password
•
Press to setup or change the "User Password".
• Press number keys to set your password on the remote control and press "MENU" to confirm.
•
Press to delete character.
•
Enter the password when you see "Confirm Password" displayed.
•
The password should be between 4 and 8 characters long.
•
If you select "Request password only when plugging the power cord in.", the projector will prompt the user to enter the password every time the power cord is plugged.
•
If you select "Always request password while projector turns on.", the user has to enter the password every time when the projector is turned on.
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•
Press to change the "Administrator Password".
•
The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to retrieve the administrator password:
•
An unique 6-digit "Universal Password" which is printed on the Security Card (please check accessory in the box). This unique password is the number which will be accepted by projector anytime no matter what the Administrator
Password is.
• If losing this security card and number, please contact with an
Acer service center.
Lock to user startup screen
Default Lock User Startup Screen is "Off". If lock user startup screen is "On", users cannot change startup screen anymore and avoid other users change that arbitrarily. Choose "Off" to unlock startup screen.
27
Note: Functions vary depending on model definition.
Management
ECO Mode
High Altitude
Turn Off Mode
Auto Shutdown
AC Power On
Lamp Hour Elapse
Lamp Reminding
Lamp Hour Reset
Choose "On" to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode.
Choose "On" to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector.
•
Instant Off: Shuts down the projector without fan cooling.
•
Instant Resume: Resumes the system when the Power button is pressed again within 2 minutes.
The projector will automatically shutdown when there is no signal input after the allocated time. (default is 120 minutes)
Choose "On" to power on projector while AC power plug in.
Displays the lamp’s elapsed operating time (in hours).
Activate this function to display a reminder to change the lamp 30 hours before its expected end-of-life.
Press the button and choose "Yes" to turn the lamp hour counter to 0 hours.
Note: Functions vary depending on model definition.
28
Audio
Volume •
Press to decrease the volume.
•
Press to increase the volume.
Mute •
Choose "On" to mute the volume.
•
Choose "Off" to restore the volume.
Power On/Off Volume Select this function to adjust the notification volume when turning the projector on/off.
Alarm Volume Select the function to adjust the volume of any warning notifications.
Note: Functions vary depending on model definition.
3D
3D
3D Format
Choose "On" to enable DLP 3D function.
•
On: Choose this item while using DLP 3D glasses, 120Hz 3D capable graphics cards and HQFS format file or DVD with corresponding SW player.
•
Off: Turn off 3D mode.
If the 3D content is not displayed correctly, you can select a 3D format that suits the 3D content you are viewing and obtain the best result.
24P 3D
3D L/R Invert
Choose "96Hz" or "144Hz" to compatible with 3D glasses.
If you see a discrete or overlapping image while wearing DLP 3D glasses, you may need to execute "Invert" to get best match of left/right image sequence to get the correct image (for DLP 3D).
3D Warning Message Choose "On" to display the 3D warning message.
29
Note: It needs correct settings on graphic card 3D application program for correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players on web page below,
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: "3D L/R Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
Language
Language
Choose the multilingual OSD menu. Use the to select your preferred menu language.
•
Press to confirm the selection.
or key
30
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center.
Image Problems and Solutions
1
#
2
Problem
No image appears onscreen
Partial, scrolling or incorrectly displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
Windows 8))
Solution
•
•
•
•
Connected as described in the "Getting Started"
section.
Ensure none of the connector pins are bent or broken.
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
Make sure you have removed the lens cap and the projector is switched on.
• Press "RESYNC" on the control panel.
• For an incorrectly displayed image:
• Open "My Computer", open the "Control
Panel", and then double-click the "Display" icon.
•
•
Select the "Settings" tab.
Verify that your display resolution setting is lower than or equal to WUXGA-RB (1920 x
1200).
•
•
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display you are using and follow the steps below:
Verify that the resolution setting is lower than or equal to WUXGA-RB (1920 x 1200).
•
•
•
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices". Next, select "Standard monitor types" under the SP box, and choose the resolution mode you need under the
"Models" box.
Verify that the resolution setting of the monitor display is lower than or equal to
WUXGA-RB (1920 x 1200).
3
4
5
6
7
8
Partial, scrolling or incorrectly displayed image
(For notebooks)
The screen of the notebook computer is not displaying your presentation
Image is unstable or flickering
•
•
•
•
•
•
•
Press "RESYNC" on the control panel.
For an incorrectly displayed image:
• Follow the steps for item 2 (above) to adjust the resolution of your computer.
• Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector.
If you are using a Microsoft ® Windows ® based notebook: Some notebook PCs may deactivate their own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to your computer's manual for detailed information.
If you are using an Apple ® Mac ® OS based notebook: In System Preferences, open Display and select Video Mirroring "On".
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
Change the display color depth settings on your computer.
Image has vertical flickering bar
Image is out of focus
Image is stretched when displaying a
"widescreen"
DVD title
•
•
Use "Frequency" to make an adjustment. Refer to the "Image" section for more information.
Check and reconfigure the display mode of your graphics card to make it compatible with the projector.
•
•
•
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the required distance of 3.3 to 23.3 feet (1.0 to 7.1
When you play a DVD encoded in anamorphic or 16:9 aspect ratio you may need to adjust the following settings:
• If you play a 4:3 format DVD title, please change the format to 4:3 in the projector OSD.
•
•
If the image is still stretched, you will also need to adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
If you play an Letterbox (LBX) format DVD title, please change the format to Letterbox (LBX) in the projector OSD.
31
32
9 Image is too small or too large
•
•
•
10 Image has slanted sides
•
•
•
11 Image is reversed
•
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press "MENU" on the remote control. Go to "Image -
-> Aspect Ratio" and try different settings or press
"RATIO" on the remote control to adjust directly.
If possible, reposition the projector so that it is centered on the screen.
Press the "Keystone / " button on the remote control until the sides are vertical.
Press "MENU" on the remote control. Go to "Image -
-> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote control.
Select "Image --> Projection Mode" on the OSD and adjust the projection direction.
33
OSD Messages
1
# Condition
Message
Message Reminder
• Fan Fail - the system fan is not working.
• Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Please check the following message.
Please also check the dust filters if they are installed. If the dust filter is clogged with dust, please clean it. Please refer to
"Cleaning and replacing the dust filters" for details.
• Replace the lamp - the lamp is about to reach its maximum lifetime. Prepare to replace it soon.
Problems with the Projector
1
#
2
Condition
The projector stops responding to all controls
Lamp burns out or makes a popping sound
Solution
If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power.
When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
34
LED & Alarm Definition Listing
LED Messages
Input power plug
Standby
Message
Power button ON
Lamp retry
Power off (Cooling state)
Lamp_LED
Red
Flash ON to
OFF 100ms
--
--
--
--
--
Temp_LED
Red
Flash ON to
OFF 100ms
--
--
--
--
--
Power LED
Red
Flash ON to
OFF 100ms
Blue
--
ON
--
--
--
ON
Quick
Flashing
-Quick
Flashing
ON -Power button OFF
(cooling completed; standby mode)
Error (thermal failure)
Error (fan lock)
Error (lamp breakdown)
Error (color wheel fail)
--
--
ON
Quick
Flashing
ON
Quick
Flashing
--
--
--
--
--
--
ON
ON
ON
ON
How to install cable management
Cable management
3
1
I. Ceiling Mount Scenario
1 Loosen the screw before removing the cable management cover from projector. (Illustration #1)
2 Carefully slide the clasp with your finger. (Illustration #2)
3 Pull out the cable management. (Illustration #3)
4 Plug in power cord and other cables you need.
5 If you need to install Acer Dongle
(WirlessHD-Kit/WirelessAndroid-Kit/WirelessCAST), follow the below steps:
(A) Install dongle rubber.
(B) Connect dongle to HDMI extension cable port.
(C) Fasten both side of dongle rubber to the specific position of cable management cover.
(D) Connect to HDMI 1/MHL port on projector.
6 Assembly the cable management cover firmly to projector, and tighten the screw. (Illustration #3,2,1)
35
36
II. Table Scenario
If you’d like to put projector on the table, you can use scissors to get rid of highlighted part, so that all the cables can be through from here (Illustration
#1)
1
2
37
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
2
1 1
Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Pull out the dust filter. (Illustration #1)
4 To clean the dust filters, use a small vacuum cleaner designed for computers and other office equipment. (Illustration #2)
5 If the dirt is difficult to remove or the filter is broken, please contact your local dealer or service center to obtain a new filter.
38
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp.
1
Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp.
2
3
4
6
5
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1 Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
2 Remove the screw that secure the lamp module. (Illustration #3)
Lift the handle so that it stands up. (Illustration #4)
Pull out the lamp plug. (Illustration #5)
3 Lift the handle so that it stands up. Pull out the lamp module by force.
(Illustration #6)
To replace the lamp module, use a new lamp and reverse the above steps.
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
39
40
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the steps below:
1 Drill four holes into a solid, structural ceiling member, and secure the ceiling mount base to the ceiling.
2 Choose the length combination based on actual environment. (CM-01S doesn’t include Type 2 and Type 3.)
Type 1 Type 2 Type 3
3 Type 1:
For the standard size use three bracket screws to mount the projector to the ceiling mount bracket.
Type 2 and Type 3:
Alternatively, for the larger size, use the sliding extensions for more supports.
Type 1: Type 2: Type 3:
41
Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution.
4 Connect the main body connector to the projector bracket (illustration 1), and then screw up four screws (illustration 2).
Illustration 1 Illustration 2
42
5 Adjust the angle and positioning as necessary.
360°
Diameter (mm)
Screw Type B
4
Length (mm)
25
SCREW SPEC. M4 x 25 mm
Large
V
Washer Type
Small
V
55.00 mm 85.00 mm
Specifications
The specifications listed below are subject to change without notice. For final specs, please refer to Acer's published marketing specifications.
Projection system
DLP ®
Resolution
Computer compatibility
• 1920x1080 1080p resolution
• Maximum: UXGA (1600 x 1200), WSXGA+
(1680x1050), 1080p(1920x1080), WUXGA-RB (1920 x 1200)
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +
Video compatibility
Aspect ratio
Displayable colors
Projection lens
Operating temperature
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Full, 4:3, 16:9, L.Box
16.7 million colors
F = 2.5 ~ 2.93, f = 15.98mm ~ 21.42mm, 1.36x Manual Zoom and
Manual Focus
Projection screen size (diagonal) 31" (79cm) ~ 300" (762cm)
Projection distance 3.3' (1.0m) ~ 23.3' (7.1m)
Throw ratio 85"@2m (1.07 ~ 1.45:1)
Horizontal scan rate
Vertical refresh scan rate
Lamp type
Keystone correction
Audio
Weight
15 - 100 kHz
24 - 120 Hz
260 W user-replaceable lamp
±30 degrees
Internal speaker with 10 W output
3.1 Kg (6.83 lbs)
Dimensions (W x D x H)
Digital Zoom
Power supply
Power consumption
373 mm X 223.4 mm X 100.5 mm (14.7" x 8.8" x 4.0")
2X
AC input 100 - 240 V auto-switching power supply
Normal mode: 315W ± 10% @ 110VAC
ECO mode: 260W ± 10% @ 110VAC
Standby mode < 0.5W
0ºC to 40ºC / 32ºF to 104ºF
43
44
I/O connectors
Standard package contents
• Power socket x1
• DC Jack x2
• VGA input x1
• Composite input x1
• YPbPr/YCbCr input x1
• HDMI (MHL) x1
• HDMI x1
• RS232 x1
• Mini USB x 1: (for firmware upgrade)
• Audio input x1
• Audio output x 1
• USB DC 5V out x1
• DC 12V out x 1
• AC power cord x1
• VGA cable x1
• HDMI extension cable x1
• Remote control x1
• Battery x2 (for remote control) (option)
• User's guide (CD-ROM) x1
• Quick start guide x1
• Security card x1
• Cable management cover x1
• Dust filters x1 (option)
• Carrying case x1 (option)
• Dongle rubber x 1
Note: Design and specifications are subject to change without notice.
45
Compatibility modes
A. VGA Analog
1 VGA Analog - PC Signal
Modes
VGA
SVGA
XGA
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4 i Mac DV (G3)
Resolution
640x480
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
640x480
800x600
1024x768
1152x870
1280x960
1024x768
V.Frequency [Hz] H.Frequency [KHz]
60
72
75
31.5
37.9
37.5
85
120
56
60
72
75
85
43.3
61.9
35.1
37.9
48.1
46.9
53.7
75
85
60
75
85
60
72
120
60
70
75
85
120
70
75
60
60
60
66.6(67)
60
60
75
75
75
75.2
65.3
75.0
31.4
34.9
37.9
48.4
68.7
75.0
60.0
67.5
77.1
64.0
77.0
80.0
91.1
60.0
77.4
48.4
56.5
60.0
68.7
99.0
63.8
46
2 VGA Analog - Extended Wide timing
Modes
WXGA
WSXGA+
WUXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
1280x800-RB
*1920x1200
1440x900
1680x1050
1920x1080
(1080P)
1366x768
1920x1200-RB
V.Frequency [Hz] H.Frequency [KHz]
60
75
47.8
60.3
85
60
120
60
119.909
60
60
60
68.6
44.8
92.9
49.6
101.6
74
59.9
65.3
60 67.5
60
59.94
47.7
74.04
3 VGA Analog -Component Signal
Modes
480i
576i
480p
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
Resolution
720x480(1440x480)
720x576(1440x576)
720x480
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
V.Frequency [Hz] H.Frequency [KHz]
59.94 (29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
60
50
15.7
15.6
31.5
31.6
45.0
37.5
33.8
28.1
27.0
67.5
56.3
B. HDMI Digital
1 HDMI - PC Signal
Modes
VGA
Resolution
640x480
640x480
640x480
640x480
V.Frequency [Hz] H.Frequency [KHz]
60
72
31.5
37.9
75
85
37.5
43.3
47
SVGA
XGA
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4 i Mac DV (G3)
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
640x480
800x600
640x480
800x600
800x600
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1024x768
1152x870
1280x960
1024x768
60
75
60
60
60
66.6(67)
60
60
72
75
85
120
70
75
85
60
75
75
75
120
56
60
72
75
85
120
60
70
75
85
60.0
75.2
65.3
75.0
31.4
34.9
37.9
99.0
63.8
67.5
77.1
64.0
77.0
80.0
91.1
61.9
35.1
37.9
48.1
46.9
53.7
77.4
48.4
56.5
60.0
68.7
48.4
68.7
75.0
60.0
2 HDMI - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
1280x800-RB
1440x900
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
60
47.8
60.3
68.6
44.8
120
60
119.909
60
92.9
49.6
101.6
59.9
48
WSXGA+
WUXGA
1920x1200
1680x1050
1920x1080
(1080P)
1366x768
1920x1200-RB
60
60
60
60
59.94
74
65.3
67.5
47.7
74.04
3 HDMI - Video Signal
Modes
480i
576i
480p
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
Resolution
720x480(1440x480)
720x576(1440x576)
720x480
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1200
V.Frequency [Hz] H.Frequency [KHz]
59.94 (29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
60
50
59.94
15.7
15.6
31.5
31.6
45.0
37.5
33.8
28.1
27.0
67.5
56.3
74.04
4 HDMI - 1.4a 3D Timing
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
720p (Frame Packing)
720p (Frame Packing)
1280 x 720
1280 x 720
1080p (Frame Packing ) 1920 x1080
720p (Frame Packing) 1280 x 720
720p (Frame Packing) 1280 x 720
1080i (Top and Bottom) 1920 x1080
1080i (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
720p (Side by Side (Half)) 1280 x 720
1080i (Side by Side (Half)) 1920 x1080
1080i (Side by Side (Half)) 1920 x1080
1080p (Side by Side (Half)) 1920 x1080
1080p (Side by Side (Half)) 1920 x1080
50
60
24
50
60
50 (25)
60 (30)
24
50
60
60
50 (25)
60 (30)
50
60
33.8
27.0
56.3
67.5
45.0
28.1
37.5
45.0
27.0
37.5
45.0
28.1
33.8
56.3
67.5
49
Graphic source monitor range limits
Horizontal scan rate:
Vertical scan rate:
Max. pixel rate:
15k-100kHz
24-120 Hz
165 MHz
C. MHL Digital
Modes Resolution
VGA
480i
576i
480p
480p_2x
576p
576p_2x
720p
720p
1080i
1080i
1080p
1080p
1080p
Graphic source monitor range limits
640x480
720x480 (1440x480)
720x576 (1440x576)
720x480
1440x480
720x576
1440x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
Horizontal scan rate:
Vertical scan rate:
Max. pixel rate:
V.Frequency
[Hz]
59.94/60
59.94/60
50(25)
59.94/60
59.94/60
50
50
59.94/60
50
60(30)
50(25)
23.97/24
25
H.Frequency
[KHz]
31.5
15.7
15.6
31.5
31.5
31.3
31.3
45.0
37.5
33.8
28.1
27.0
28.1
29.97/30
15k-50 kHz
33.8
24-60 Hz
Digital: 75 MHz
50
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
•
•
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
51
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
001
Radio device regulatory notice
Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio communication devices (RSS-210)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail: [email protected]
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it
Declare under our own responsibility that the product:
Product:
Trade Name:
Model Number:
DLP Projector
Acer
D1P1434
H8550BD/V7500/HV750/V240/HT-820
To which this declaration refers conforms to the relevant standard or other standardizing documents: x EN55022:2010 Class B; EN 55024:2010 x EN61000-3-2:2006+A1:2009+A2:2009, Class A x
EN61000-3-3:2008 x
EN 60950-1:2006/A11:2009/A1:2010+A12:2011 x
Regulation (EC) No. 1275/ 2008; EN 62301:2005 x
EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign requirements for energy-related product.
Year to begin affixing CE marking 2015.
_______________________________ Jun, 01, 2015
RU Jan / Sr. Manager Date
Regulation, Acer Inc.
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147 www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product: DLP Projector
Model Number: D1P1434
Machine Type: H8550BD/V7500/HV750/V240/HT-820
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
advertisement
Related manuals
advertisement