Hewlett-Packard computer User Guide
Реклама
Реклама
Regulatory, Safety and Environmental Notices
User Guide
© Copyright 2007 Hewlett-Packard
Development Company, L.P.
Windows and Windows Vista are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the
United States and other countries. ENERGY
STAR is a U.S. registered mark of the United
States Environmental Protection Agency.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Seventh Edition: October 2007
First Edition: January 2007
Document Part Number: 437312-007
Table of contents
Products with wireless LAN devices or HP Broadband Wireless Modules .......................... 3
iii
iv
1 Regulatory notices
This guide provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product.
One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply on-board airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on.
To identify a hardware device, such as a wireless LAN (WLAN) network device, installed on the computer, open the Device Manager utility.
In Windows Vista® , follow these steps:
1.
Select Start > Computer > System properties .
2.
In the left pane, click Device Manager .
In Windows® XP Professional and Windows XP Home , follow these steps:
1.
Select Start > My Computer .
2.
If the left pane, select View System Information > Hardware tab > Device Manager .
Regulatory markings for your country may be located on the bottom of the product, under the battery, under a user-removable door (or some other user-accessible location), or on the wireless or modem module.
1
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods.
2 Chapter 1 Regulatory notices
Declaration of Conformity for products marked with the FCC logo
(United States only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired operation.
If you have questions about the product that are not related to this declaration, write to
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, TX 77269-2000
For questions regarding this FCC declaration, write to
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, TX 77269-2000 or call HP at 281-514-3333
To identify your product, refer to the part, series, or model number located on the product.
Products with wireless LAN devices or HP Broadband Wireless Modules
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
WARNING!
Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation of tablet PCs and notebooks.
During normal operation of tablet PCs: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennae should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennae, refer to the Tablet PC Tour user guide included with the computer.
During normal operation of notebooks: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennae should not be less than 20 cm (8 inches), including when the computer display is closed. To identify the location of the wireless antennae, refer to the
Notebook Tour user guide included with the computer.
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to cochannel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-
GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device.
Federal Communications Commission notice 3
Brazilian notice
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.
Este equipamento atende aos limites de Taxa de Absorção Específica referente à exposição a campos elétricos, magnéticos e eletromagnéticos de radiofreqüências adotados pela ANATEL.
Unless the computer has an Intel® PRO/Wireless 2100 Wireless LAN radio or an Intel PRO/Wireless
2200 Wireless LAN radio, the Brazilian certification mark is located on the bottom of the computer.
Wireless LAN certification markings
The Intel PRO/Wireless 2100 Wireless LAN has the certification mark below:
The Intel PRO/Wireless 2200 Wireless LAN has the certification mark below:
Canadian notices
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations. Wireless operation is subject to 2 conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device.
The antennae for this device are not replaceable. Any attempt at user access will damage your computer.
4 Chapter 1 Regulatory notices
For radio devices in the 5250- to 5350-MHz and 5470- to 5725-MHz bands, the maximum gain as specified by the Canadian e.i.r.p. limit is noted below:
● Broadcom 802.11a/b/g WLAN = 5.6 dBi
● Broadcom 4321AG 802.11a/b/g/draft-n Wi-Fi Adapter = 5.6 dBi
● Intel PRO/Wireless 3945ABG = 6 dBi
● Intel Wireless WiFi Link 4965AG = 6 dBi
● Intel Wireless WiFi Link 4965AGN = 6 dBi
For radio devices in the 5725- to 5825-MHz band, the maximum gain permitted, as specified by the
Canadian e.i.r.p. limits for point-to-point and non-point-to-point operation, is noted below:
● Broadcom 802.11a/b/g WLAN = 5.8 dBi
● Broadcom 4321AG 802.11a/b/g/draft-n Wi-Fi Adapter = 5.8 dBi
● Intel PRO/Wireless 3945ABG = 6 dBi
● Intel Wireless WiFi Link 4965AG = 6 dBi
● Intel Wireless WiFi Link 4965AGN = 6 dBi
European Union notices
Products bearing the CE marking comply with the following EU Directives:
● Low Voltage Directive 2006/95/EC
● EMC Directive 2004/108/EC
CE compliance of this product is valid only if powered with the correct CE-marked AC adapter provided by HP.
If this product has telecommunications functionality, it also complies with the essential requirements of the following EU Directive:
● R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards (European
Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family.
This compliance is indicated by one of the following conformity markings placed on the product.
● The following CE marking is valid for non-telecommunications products and for EU harmonized telecommunications products, such as Bluetooth®.
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany
European Union notices 5
● The following CE marking is valid for EU non-harmonized telecommunications products.
*If applicable, a notified body number is used. Refer to the regulatory label provided on this product.
The telecommunications functionality of this product may be used in the following EU and EFTA countries:
Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland, and United Kingdom.
Products with 2.4-GHz wireless LAN devices
France
L'utilisation de cet equipement (2.4GHz Wireless LAN) est soumise a certaines restrictions : Cet equipement peut être utilisé a l'interieur d'un batiment en utilisant toutes les frequences de 2400 a
2483.5MHz (Chaîne 1-13). Pour une utilisation en environnement exterieur, les frequences comprises entre 2400-2454 MHz (Chaîne 1-9) peuvent être utilisé. Pour les dernieres restrictions, voir http://www.arcep.fr
.
For 2.4 GHz Wireless LAN operation of this product certain restrictions apply: This product may be used indoor for the entire 2400-2483.5 MHz frequency band (channels 1-13). For outdoor use, only 2400-2454
MHz frequency band (channels 1-9) may be used. For the latest requirements, see http://www.arcep.fr
.
Italy
E'necessaria una concessione ministeriale anche per l'uso del prodotto. Verifici per favore con il proprio distributore o direttamente presso la Direzione Generale Pianificazione e Gestione Frequenze.
License required for use. Verify with your dealer or directly with the General Direction for Frequency
Planning and Management (Direzione Generale Pianificazione e Gestione Frequenze).
Products with 5-GHz wireless LAN devices
Frequency availability for 802.11a or 802.11h wireless LAN is not currently harmonized throughout the
European Union. For compliance requirements, users should verify compliance with their supplier, local
HP office, or telecommunications authority.
Products with HP Broadband Wireless Modules
THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO FREQUENCY
RADIATION.
The HP Broadband Wireless Module in your notebook is a radio transmitter and receiver. The device is designed not to exceed the limits for exposure to radio frequency (RF) recommended by international guidelines (ICNIRP). These limits are part of comprehensive guidelines that establish permitted levels
6 Chapter 1 Regulatory notices
of RF radiation for the general population. The guidelines were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The device also meets the
European R&TTE directives, including the protection of the health and the safety of the user and any other person.
The exposure standard for mobile devices employs a unit of measurement known as the Specific
Absorption Rate (SAR).* The SAR was obtained by testing the device at standard operating positions with the device transmitting at its highest certified power level in all tested frequency bands. The SAR information for your computer, including the recommended minimum distance from the body, is available on the HP Web site at http://www.hp.com/broadbandwireless . The actual SAR of the device while operating can be well below the maximum value, because the device operates at multiple power levels and uses only the power required to reach the network.
When installed in the notebook computer, this device meets RF exposure guidelines when the antennae are positioned at a minimum distance from the body. In order to transmit data or messages, this device requires a quality connection to the network. In some cases, transmission of data or messages may be delayed until such a connection becomes available. Be sure that the recommended distance is observed until the transmission is complete.
*The non-FCC, international guidelines state that the SAR limit for mobile devices used by the public is
2.0 watts/kilogram (W/kg) averaged over 10 grams of body tissue. The guidelines incorporate a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. SAR values may vary depending on national reporting requirements and the network band.
Ergonomics notice
Germany
Mobile Computer, welche das "GS" Zeichen tragen, entsprechen den ergonomischen Anforderungen und sind nur für kurzzeitige Benutzung von Bildschirmarbeitsaufgaben geeignet. Wird ein mobiler
Computer für Bildschirmarbeitsaufgaben verwendet, wo die Richtlinie 90/270/EEG
(Bildschirmarbeitsrichtlinie) anzuwenden ist, wird eine geeignete externe Tastatur notwendig. Abhängig von der Anwendung und der Aufgabe kann ein geeigneter externer Monitor erforderlich sein, um vergleichbare Arbeitsbedingungen zu einem stationären Arbeitsplatz zu erreichen.
Indian notice
The India Telegraph Act of 1885 requires that an IEEE 802.11a wireless LAN end user obtain a license.
To obtain this license, please contact The Wireless Planning & Coordination Wing, Ministry of
Communications, Sanchar Ghavan New Delhi.
Japanese notices
Indian notice 7
Wireless LAN 802.11b devices
Wireless LAN 802.11g devices
Wireless LAN certification markings
The Intel PRO/Wireless 2200b/g Wireless LAN has the certification mark below:
The Intel PRO/Wireless 2915a/b/g Wireless LAN has the certification mark below:
The Intel PRO/Wireless 3945a/b/g Wireless LAN has the certification mark below:
8 Chapter 1 Regulatory notices
The Intel Wireless WiFi Link 4965AG has the certification mark below:
The Intel Wireless WiFi Link 4965AGN has the certification mark below:
The Broadcom 802.11b/g Wireless LAN has the certification mark below:
The Broadcom 4311BG 802.11b/g Wireless LAN has the certification mark below:
The Broadcom 4311AG 802.11a/b/g Wireless LAN has the certification mark below:
The Broadcom 802.11a/b/g Wireless LAN has the certification mark below:
The Broadcom 802.11b/g Wireless LAN with Broadrange has the certification mark below:
Japanese notices 9
The Broadcom 802.11a/b/g Wireless LAN with Broadrange has the certification mark below:
The Atheros 2425BG 802.11b/g WiFi Adapter has the certification mark below:
The Broadcom 4321AG 802.11a/b/g/draft-n Wi-Fi Adapter has the certification mark below:
The Broadcom 802.11b/g WLAN has the certification mark below:
Wireless WAN certification markings
The HP hs2300 HSDPA Broadband Wireless Module has the certification mark below:
Bluetooth devices
10 Chapter 1 Regulatory notices
Certification markings for Bluetooth devices
The HP integrated module with Bluetooth 2.0 has the certification mark below:
Korean notice
Singaporean wireless notice
Turn off any WWAN devices while you are onboard aircraft. The use of these devices onboard aircraft is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, or legal action, or both.
Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress.
As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antenna during operation of the equipment.
This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands. The SAR data information is based on CENELEC's standards EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaged over 10 grams of tissue.
Taiwan notice
Korean notice 11
Airline travel notice
Use of electronic equipment onboard commercial aircraft is at the discretion of the airline.
Battery notices
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
For information about removing a battery, refer to the user guide included with the product.
ENERGY STAR compliance
HP computers marked with the ENERGY STAR® logo are compliant with the applicable U.S.
Environmental Protection Agency (EPA) ENERGY STAR specifications for computers. The EPA
ENERGY STAR logo does not imply endorsement by the EPA. As an ENERGY STAR Partner, Hewlett-
Packard Company has determined that the products marked with the ENERGY STAR logo are ENERGY
STAR qualified as per the applicable ENERGY STAR guidelines for energy efficiency. The following logo will appear on all ENERGY STAR qualified computers:
The ENERGY STAR program for computers was created by the EPA to promote energy efficiency and reduce air pollution through more energy-efficient equipment in homes, offices, and factories. One way that products achieve this goal is by using the Microsoft® Windows® power management feature to reduce power consumption when the product is not in use.
The power management feature allows the computer to initiate a low-power or “Sleep” mode after a period of user inactivity. When used with an external ENERGY STAR qualified monitor, this feature also supports similar power management features of the monitor. To take advantage of these potential energy savings, the power management feature has been preset to behave in the following ways when the system is operating on AC power:
● Turn off the display after 15 minutes
● Initiate Sleep after 30 minutes
The computer exits Sleep when the power/Sleep button is pressed. When the Wake On LAN (WOL) feature is enabled, the computer can also exit Sleep in response to a network signal.
Additional information on the potential energy and financial savings of the power management feature can be found on the EPA ENERGY STAR Power Management Web site at http://www.energystar.gov/ powermanagement .
Additional information on the ENERGY STAR program and its environmental benefits are available on the EPA ENERGY STAR Web site at http://www.energystar.gov
.
Laser compliance
This product may be provided with a device containing a laser that is classified as a Class 1 Laser
Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation.
12 Chapter 1 Regulatory notices
Each laser product complies with 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser
Notice No. 50, dated May 27, 2001; and with IEC 60825-1:1993/A2:2001.
WARNING!
Use of controls or adjustments, or performance of procedures other than those specified in the laser product installation guide, may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:
Do not try to open the module enclosure. There are no user-serviceable components inside.
Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified in the laser product installation guide.
Allow only authorized service providers to repair the unit.
Modem notices
WARNING!
To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following:
Do not use this product near water—for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning.
Do not use this product to report a gas leak while in the vicinity of the leak.
Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component.
If this product was not provided with a telephone line cord, use only 0.126 mm 2 (No. 26 AWG) or larger telecommunication line cord.
Do not plug a modem or telephone cable into the RJ-45 (network) jack.
SAVE THESE INSTRUCTIONS
Telecommunications device approvals
The telecommunications device in the computer is approved for connection to the telephone network in the countries and regions whose approval markings are indicated on the product label located on the bottom of the computer or on the modem.
Refer to the user guide included with the product to ensure that the product is configured for the country or region in which the product is located. Selecting a country or region other than the one in which it is located may cause the modem to be configured in a way that violates the telecommunication regulations/ laws of that country or region. In addition, the modem may not function properly if the correct country or region selection is not made. If, when you select a country or region, a message appears that states that the country or region is not supported, this means that the modem has not been approved for use in this country or region and thus should not be used.
U.S. modem statements
This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA.
On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone company if you are requested to do so.
Modem notices 13
Applicable certification jack USOC = RJ11C.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn't practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service.
If trouble is experienced with this equipment, call technical support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should perform repairs only to the equipment specifically discussed in the
“Troubleshooting” section of the user guide, if one is provided.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including a fax machine, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges).
In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions.
U.S. modem declarations
Refer to the following modem vendor declarations for the modem device installed in your computer:
14 Chapter 1 Regulatory notices
Modem notices 15
16 Chapter 1 Regulatory notices
Modem notices 17
18 Chapter 1 Regulatory notices
Modem notices 19
20 Chapter 1 Regulatory notices
Modem notices 21
Canadian modem statements
This equipment meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all devices does not exceed 5.
The REN for this terminal equipment is 1.0.
Japanese modem statements
If the computer does not have the Japanese certification mark on the bottom of the computer, refer to the appropriate certification marking below.
The Japanese certification mark for the Agere Systems AC'97 modem is below:
The Japanese certification mark for the HDAUDIO Soft Data Fax Modem with SmartCP is below:
The Japanese certification mark for the Agere Systems HDA modem is below:
The Japanese certification mark for the HDAUDIO Soft Data Fax Modem with SmartCP is below:
The Japanese certification mark for the V.92 56K Data/Fax Modem is below:
22 Chapter 1 Regulatory notices
The Japanese certification mark for the V.92 56K Data/Fax Modem is below:
The Japanese certification mark for the V.92 56K Data/Fax Modem is below:
New Zealand modem statements
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.
If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing.
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service.
Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications: a.
There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation.
b.
The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt.
c.
Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt.
d.
The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (So set between 2 and 10).
Voice support
All persons using this device for recording telephone conversations shall comply with New Zealand law.
This requires that at least one party to the conversation is aware that it is being recorded. In addition,
Modem notices 23
the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used, and what is disclosed to any other party.
This equipment shall not be set to make automatic calls to the Telecom ‘111' Emergency Service.
Power cord notice
If you were not provided with a power cord for the computer or for an external power accessory intended for use with the computer, you should purchase a power cord that is approved for use in your country or region.
The power cord must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of
0.75 mm²/18AWG, and the length of the cord must be between 1.5 m (5 ft) and 2 m (6½ ft). If you have questions about the type of power cord to use, contact your authorized service pr ovider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.
Japanese power cord notice
Macrovision Corporation notice
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
24 Chapter 1 Regulatory notices
2 Safety notices
Heat-related safety warning notice
WARNING!
To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
Battery notices
WARNING!
To reduce the risk of fire or burns, do not disassemble, crush, or puncture a battery; short the external contacts on a battery; or dispose of a battery in fire or water. Do not expose a battery to temperatures above 60°C (140°F).
WARNING!
Keep the battery away from children.
WARNING!
To reduce potential safety issues, only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased as an accessory from HP should be used with the computer.
Headset and earphone volume level notice
WARNING!
Listening to music at high volume levels and for extended durations can damage one’s hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and reduce the amount of time listening at high levels.
For your own safety, before using headsets or earphones, always reset the volume. Some headphones are louder than other headphones, even if the volume control setting is the same.
Changing the default audio or equalizer settings might lead to higher volume and should only be done with caution.
For your own safety, headsets or earphones used with this product should comply with the headphone limits in EN 50332-2.
If the computer includes a headset or earphones, this combination is in compliance to EN 50332-1.
Heat-related safety warning notice 25
Power cord notices
WARNING!
To reduce the risk of electric shock or damage to the equipment:
Plug the power cord into an AC outlet that is easily accessible at all times.
Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer).
If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature.
WARNING!
To reduce potential safety issues, only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used with the computer.
26 Chapter 2 Safety notices
Cleaning the keyboard
WARNING!
To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface. Clean the keyboard regularly to prevent keys from sticking and to remove dust, lint, and particles that can become trapped beneath the keys. A can of compressed air with a straw extension can be used to blow air around and under the keys to loosen and remove debris.
Travel notice
WARNING!
To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances.
Norway and Sweden: Cable grounding notice for products with a TV tuner
CAUTION: To reduce potential safety issues, use a galvanic isolator when connecting to a cable distribution system.
Cleaning the keyboard 27
3 Environmental notices
This chapter provides country- and region-specific environmental notices and compliance information.
Some of these notices may not apply to your product.
Battery disposal
WARNING!
When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.
Electronic hardware and battery recycling
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle .
Disposal of waste equipment by users in private households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.
28 Chapter 3 Environmental notices
Chinese material content declarations
The Table of Toxic and Hazardous Substances/Elements and their Content
As required by China's Management Methods for Controlling Pollution by Electronic Information
Products
Part Name
Battery
Cables
Camera
Chassis/Other
Flash memory card reader
Floppy disk drive
Hard disk drive
Headphones
I/O PCAs
Keyboard
Liquid crystal display
(LCD) panel
Media (CD/DVD/floppy)
Memory
Motherboard, processor, heat sinks
Mouse
Optical disk drive
Optional docking device
Power adapter
Power supply
Remote control
Smart card/Java card reader
Speakers, external
TV tuner
USB flash memory drive
Lead
(Pb)
X
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
O
O
O
X
O
O
O
O
Mercury
(Hg)
O
Toxic and Hazardous Substances and Elements
Cadmium
(Cd)
O
Hexavalent
Chromium
(Cr(VI))
O
Polybrominated biphenyls (PBB)
O
Polybrominated diphenyl ethers
(PBDE)
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Chinese material content declarations 29
USB hub
Web camera
Wireless receiver
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Wireless cards X O O O O O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.
All parts named in this table with an X are in compliance with the European Union's RoHS Legislation "Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment."
NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity.
30 Chapter 3 Environmental notices
ḍЁ lj⬉ᄤֵᙃѻક∵ᶧࠊㅵ⧚ࡲ⊩NJ
Toxic and Hazardous Substances and Elements
䪙 (Pb) ∲ (Hg) 䬝 (Cd) ݁Ӌ䫀 (Cr(VI)) ⒈㘨㣃 (PBB) ⒈Ѡ㣃䝮 (PBDE)
⬉∴
⬉㓚
✻Ⳍᴎ
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O ᴎㆅ
䮾ᄬ䇏व఼
䕃偅
/ ݊Ҫ
⹀Ⲭ
㘇ᴎ
I/O PCAs
X
X
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
䬂Ⲭ
⎆ᰒ⼎ሣ ҟ䋼 ˄
ݙᄬᴵ
CD/DVD/ 䕃Ⲭ˅
X
X
O
X
X
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Џᵓˈ໘⧚఼ᬷ⛁఼
哴ᷛ
ܝ偅
ᇍ䆒䗝ӊ
⬉⑤䗖䜡఼
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
⬉⑤
䘹఼
X
X
O
O
O
O
O
O
O
O
O
O
Smart व / Java व䇏व఼
㕂ᡀໄ఼
⬉㾚ᬊ఼
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
USB 䮾ᄬⲬ
USB 䲚㒓఼
㔥㒰ᨘڣ༈
X
X
O
O
O
O
O
O
O
O
O
O
᮴㒓ᬊ఼
᮴㒓㔥व
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O ˖㸼⼎䆹᳝↦᳝ᆇ⠽䋼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ䞣ഛ SJ/T11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
X ˖㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ䞣䍙ߎ SJ/T11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ
㸼Ё᳝ᷛ Ā X āⱘ᠔᳝䚼ӊ䛑ヺড়ⲳ RoHS ⊩㾘 Ā⌆䆂Ӯⲳ⧚џӮ 2003 ᑈ 1 ᳜ 27 ᮹݇Ѣ⬉ᄤ⬉఼䆒Ё䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ⱘ 2002/95/EC োᣛҸāDŽ
⊼˖ ⦃ֱՓ⫼ᳳ䰤ⱘখ㗗ᷛ䆚পއѢѻકℷᐌᎹⱘ⏽ᑺᑺㄝᴵӊDŽ
Chinese material content declarations 31
Japanese material content declaration
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that manufacturers provide material content declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, see the HP Web site at http://www.hp.com/go/jisc0950 .
United States mercury disposal
This computer contains mercury in the fluorescent lamp of the computer display, which may require special handling when the computer has reached the end of its useful life. Because of environmental considerations, local authorities may regulate the disposal of the mercury.
For disposal or recycling information, please contact your local authorities or the Electronic Industries
Alliance (EIA) at http://www.eiae.org
.
Perchlorate material - special handling may apply
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate .
This product’s real-time clock battery or coin cell battery may contain perchlorate and may require special handling when recycled or disposed of in California.
32 Chapter 3 Environmental notices
Index
Symbols/Numerics
2.4-GHz wireless LAN
A
B
C
Chinese Material Content
D
disposal notices
E electronic hardware and battery
environmental notices 28 equipment disposal notice 28
F
Federal Communications
Commission
cables 2 modifications 2 notice 2
France, 2.4-GHz wireless LAN
H
hardware device, identifying 1
headset and earphone volume level
I
Italy, 2.4-GHz wireless LAN
J
Japanese material content
K
L
M
Macrovision Corporation
modem statements
modifications, Federal
N
New Zealand modem
notices
environmental 28 equipment disposal 28
Federal Communications
headset and earphone volume
P
S
Singaporean wireless notice 11
Index 33
T
TV tuner, cable grounding
U
V
W
34 Index
Скачать
Общедоступная ссылка обновлена
Общедоступная ссылка на ваш чат была обновлена. Вы можете просматривать и управлять своими ссылками на чат после регистрации здесь.
Общедоступная ссылка на документ
Реклама