HP computer User guide
Below you will find brief information for computer. This user guide provides country-specific nonwireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product. One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply onboard airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on.
Advertisement
Advertisement
Regulatory, Safety and Environmental
Notices
User Guide
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
© Copyright 2007 Hewlett-Packard
Development Company, L.P.
Windows and Windows Vista are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the
United States and other countries. Energy
Star is a U.S. registered mark of the United
States Environmental Protection Agency.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Second Edition: January 2007
Document Part Number: 437312-002
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Table of contents
iii ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
iv
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
1 Regulatory notices
This guide provides country-specific nonwireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product.
One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply onboard airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on.
To identify a hardware device, such as a wireless LAN (WLAN) network device, installed on the computer, open the Device Manager utility.
In Windows Vista™, follow these steps:
1.
Select Start > Computer > System properties .
2.
In the left pane, click Device Manager .
In Windows® XP Professional and Windows XP Home, follow these steps:
1.
Select Start > My Computer .
2.
If the left pane, select View System Information > Hardware tab > Device Manager .
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
1
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods.
2 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
Declaration of Conformity for products marked with the FCC logo
(United States only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired operation.
If you have questions about the product that are not related to this declaration, write to
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, TX 77269-2000
For questions regarding this FCC declaration, write to
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, TX 77269-2000 or call HP at 281-514-3333
To identify your product, refer to the part, series, or model number located on the product.
Products with wireless LAN devices
WARNING!
Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation of tablet PCs and notebooks.
During normal operation of tablet PCs: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennae should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennae, refer to the Tablet PC Tour user guide included with the computer.
During normal operation of notebooks: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennae should not be less than 20 cm
(8 inches), including when the computer display is closed. To identify the location of the wireless antennae, refer to the Notebook Tour user guide included with the computer.
CAUTION When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device.
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Federal Communications Commission notice 3
Brazilian notice
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.
Unless the computer has an Intel® PRO/Wireless 2100 Wireless LAN radio or an Intel PRO/Wireless
2200 Wireless LAN radio, the Brazilian certification mark is located on the bottom of the computer.
Wireless LAN certification markings
The Intel PRO/Wireless 2100 Wireless LAN has the certification mark below:
The Intel PRO/Wireless 2200 Wireless LAN has the certification mark below:
Canadian notices
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations. Wireless operation is subject to 2 conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device.
The antennae for this device are not replaceable. Any attempt at user access will damage your computer.
For radio devices in the 5250- to 5350-MHz and 5470- to 5725-MHz bands, the maximum gain as specified by the Canadian e.i.r.p. limit is noted below:
● Broadcom 802.11a/b/g WLAN = 5.6 dBi
● Broadcom 4321AG 802.11a/b/g/draft-n Wi-Fi Adapter = 5.6 dBi
ENWW 4 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
● Intel PRO/Wireless 3945ABG = 6 dBi
● Intel Wireless WiFi Link 4965AG = 6 dBi
● Intel Wireless WiFi Link 4965AGN = 6 dBi
For radio devices in the 5725- to 5825-MHz band, the maximum gain permitted, as specified by the
Canadian e.i.r.p. limits for point-to-point and non-point-to-point operation, is noted below:
● Broadcom 802.11a/b/g WLAN = 5.8 dBi
● Broadcom 4321AG 802.11a/b/g/draft-n Wi-Fi Adapter = 5.8 dBi
● Intel PRO/Wireless 3945ABG = 6 dBi
● Intel Wireless WiFi Link 4965AG = 6 dBi
● Intel Wireless WiFi Link 4965AGN = 6 dBi
Avis Canadien
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
European Union notices
Products bearing the CE marking comply with the following EU Directives:
● Low Voltage Directive 73/23/EEC
● EMC Directive 89/336/EEC
CE compliance of this product is valid only if powered with the correct CE-marked AC adapter provided by HP.
If this product has telecommunications functionality, it also complies with the essential requirements of the following EU Directive:
● R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards (European
Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family.
This compliance is indicated by one of the following conformity markings placed on the product.
● The following CE marking is valid for non-telecommunications products and for EU harmonized telecommunications products, such as Bluetooth®.
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany
Avis Canadien 5 ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
● The following CE marking is valid for EU non-harmonized telecommunications products.
*If applicable, a notified body number is used. Refer to the regulatory label provided on this product.
The telecommunications functionality of this product may be used in the following EU and EFTA countries:
Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, and United
Kingdom.
Products with 2.4-GHz wireless LAN devices
France
L'utilisation de cet equipement (2.4GHz wireless LAN) est soumise à certaines restrictions : cet equipement peut être utilisé à l'interieur d'un batiment en utilisant toutes les frequences de 2400 a
2483.5MHz (Chaine 1–13). Pour une utilisation en environnement exterieur, vous devez utiliser les frequences comprises entre 2454 a 2483.5-MHz (Chaine 10–13). Pour les dernières restrictions, voir http://www.art-telecom.fr
.
For 2.4-GHz wireless LAN operation of this product, certain restrictions apply. This equipment may use the entire 2400-MHz to 2483.5-MHz frequency band (channels 1 through 13) for indoor applications.
For outdoor use, the 2454-MHz to 2483.5-MHz frequency band (channels 10 through 13) may not be used. For the latest requirements, see http://www.art-telecom.fr
.
Italy
E'necessaria una concessione ministeriale anche per l'uso del prodotto. Verifici per favore con il proprio distributore o direttamente presso la Direzione Generale Pianificazione e Gestione Frequenze.
License required for use. Verify with your dealer or directly with the General Direction for Frequency
Planning and Management (Direzione Generale Pianificazione e Gestione Frequenze).
Products with 5-GHz wireless LAN devices
Frequency availability for 802.11a or 802.11h wireless LAN is not currently harmonized throughout the
European Union. For compliance requirements, users should verify compliance with their supplier, local
HP office, or telecommunications authority.
Ergonomics notice
Germany
Computers bearing the “GS” approval mark meet the applicable ergonomic requirements when used in conjunction with docking bases, keyboards, and monitors that bear the “GS” approval mark. Computers in a stand-alone mode are not intended for continuous use in an office environment.
ENWW 6 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Indian notice
The India Telegraph Act of 1885 requires that an IEEE 802.11a wireless LAN end user obtain a license.
To obtain this license, please contact The Wireless Planning & Coordination Wing, Ministry of
Communications, Sanchar Ghavan New Delhi.
Japanese notices
Wireless LAN 802.11b devices
Wireless LAN 802.11g devices
Wireless LAN certification markings
The Intel PRO/Wireless 2200b/g Wireless LAN has the certification mark below:
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Indian notice 7
The Intel PRO/Wireless 2915a/b/g Wireless LAN has the certification mark below:
The Intel PRO/Wireless 3945a/b/g Wireless LAN has the certification mark below:
The Broadcom 802.11b/g Wireless LAN has the certification mark below:
The Broadcom 4311BG 802.11b/g Wireless LAN has the certification mark below:
The Broadcom 4311AG 802.11a/b/g Wireless LAN has the certification mark below:
The Broadcom 802.11a/b/g Wireless LAN has the certification mark below:
The Broadcom 802.11b/g Wireless LAN with Broadrange has the certification mark below:
8 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
The Broadcom 802.11a/b/g Wireless LAN with Broadrange has the certification mark below:
Bluetooth devices
Certification markings for Bluetooth devices
The HP integrated module with Bluetooth has the certification mark below:
The HP integrated module with Bluetooth 2.0 has the certification mark below:
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Japanese notices 9
Korean notice
Singaporean wireless notice
Turn off any WWAN devices while you are onboard aircraft. The use of these devices onboard aircraft is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, or legal action, or both.
Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress.
As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antenna during operation of the equipment.
This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands. The SAR data information is based on CENELEC's standards EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaged over 10 grams of tissue.
Taiwan notice
Airline travel notice
Use of electronic equipment onboard commercial aircraft is at the discretion of the airline.
Battery notices
CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
For information about removing a battery, refer to the user guide included with the product.
ENWW 10 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Energy Star compliance
Computers bearing the Energy Star® logo are compliant with the U.S. Environmental Protection Agency
(EPA) Energy Star Computers Program 3.0. The EPA Energy Star logo does not imply endorsement by the EPA. As an Energy Star Partner, HP has determined that the product meets the Energy Star guidelines for energy efficiency.
Laser compliance
This product may be provided with a device containing a laser that is classified as a Class 1 Laser
Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation.
Each laser product complies with 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser
Notice No. 50, dated May 27, 2001; and with IEC 60825-1:1993/A2:2001.
WARNING!
Use of controls or adjustments, or performance of procedures other than those specified in the laser product installation guide, may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:
Do not try to open the module enclosure. There are no user-serviceable components inside.
Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified in the laser product installation guide.
Allow only authorized service providers to repair the unit.
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Energy Star compliance 11
Modem notices
WARNING!
To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following:
Do not use this product near water—for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning.
Do not use this product to report a gas leak while in the vicinity of the leak.
Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component.
If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord.
Do not plug a modem or telephone cable into the RJ-45 (network) jack.
SAVE THESE INSTRUCTIONS
Telecommunications device approvals
The telecommunications device in the computer is approved for connection to the telephone network in the countries whose approval markings are indicated on the product label located on the bottom of the computer or on the modem.
Refer to the user guide included with the product to ensure that the product is configured for the country in which the product is located. Selecting a country other than the one in which it is located may cause the modem to be configured in a way that violates the telecommunication regulations/laws of that country. In addition, the modem may not function properly if the correct country selection is not made.
If, when you select a country, a message appears that states that the country is not supported, this means that the modem has not been approved for use in this country and thus should not be used.
12 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
U.S. modem statements
This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA.
On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone company if you are requested to do so.
Applicable certification jack USOC = RJ11C.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn't practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service.
If trouble is experienced with this equipment, call technical support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should perform repairs only to the equipment specifically discussed in the
“Troubleshooting” section of the user guide, if one is provided.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including a fax machine, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges).
In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions.
Modem notices 13 ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
U.S. modem declarations
Refer to the following modem vendor declarations for the modem device installed in your computer:
14 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Modem notices 15
16 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Modem notices 17
18 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Modem notices 19
Canadian modem statements
This equipment meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all devices does not exceed 5.
The REN for this terminal equipment is 1.0.
Japanese modem statements
If the computer does not have the Japanese certification mark on the bottom of the computer, refer to the appropriate certification marking below.
The Japanese certification mark for the Agere Systems AC'97 modem is below:
The Japanese certification mark for the HDAUDIO Soft Data Fax Modem with SmartCP is below:
The Japanese certification mark for the Agere Systems HDA modem is below:
The Japanese certification mark for the HDAUDIO Soft Data Fax Modem with SmartCP is below:
20 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
New Zealand modem statements
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.
If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing.
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service.
Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications: a.
There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation.
b.
The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt.
c.
Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt.
d.
The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (So set between 2 and 10).
Voice support
All persons using this device for recording telephone conversations shall comply with New Zealand law.
This requires that at least one party to the conversation is aware that it is being recorded. In addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used, and what is disclosed to any other party.
This equipment shall not be set to make automatic calls to the Telecom ‘111' Emergency Service.
Modem notices 21 ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Power cord notice
If you were not provided with a power cord for the computer or for an external power accessory intended for use with the computer, you should purchase a power cord that is approved for use in your country.
The power cord must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of
0.75 mm²/18AWG, and the length of the cord must be between 1.5 m (5 ft) and 2 m (6½ ft). If you have questions about the type of power cord to use, contact your authorized service provider.
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.
Japanese power cord notice
Macrovision Corporation notice
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
22 Chapter 1 Regulatory notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
2 Safety notices
Battery notices
WARNING!
To reduce the risk of fire or burns, do not disassemble, crush, or puncture a battery; short the external contacts on a battery; or dispose of a battery in fire or water. Do not expose a battery to temperatures above 60°C (140°F).
WARNING!
Keep the battery away from children.
WARNING!
To reduce potential safety issues, only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased as an accessory from
HP should be used with the computer.
Headset and earphone volume level notice
Listening to music at high volume levels and for extended durations can damage one’s hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and reduce the amount of time listening at high levels.
● For your own safety, headsets or earphones used with this product should comply with the headphone limits in clause 7 of EN 50332-2.
● If a headset or earphones are shipped with this product, they are in compliance to EN 50332-1.
Power cord notices
WARNING!
To reduce the risk of electric shock or damage to the equipment:
Plug the power cord into an AC outlet that is easily accessible at all times.
Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer).
If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed)
3-pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature.
WARNING!
To reduce potential safety issues, only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from
HP should be used with the computer.
Battery notices 23 ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Travel notice
WARNING!
To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances.
24 Chapter 2 Safety notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
3 Environmental notices
This chapter provides country-specific environmental notices and compliance information. Some of these notices may not apply to your product.
Battery disposal
WARNING!
When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.
Electronic hardware and battery recycling
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle .
Disposal of waste equipment by users in private households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.
Battery disposal 25 ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Chinese material content declarations
The Table of Toxic and Hazardous Substances/Elements and their Content
As required by China's Management Methods for Controlling Pollution by Electronic Information
Products
26 Chapter 3 Environmental notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Chinese material content declarations 27
Japanese material content declaration
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that manufacturers provide material content declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, see the HP Web site at http://www.hp.com/go/jisc0950 .
United States mercury disposal
This computer contains mercury in the fluorescent lamp of the computer display, which may require special handling when the computer has reached the end of its useful life. Because of environmental considerations, local authorities may regulate the disposal of the mercury.
For disposal or recycling information, please contact your local authorities or the Electronic Industries
Alliance (EIA) at http://www.eiae.org
.
Perchlorate material - special handling may apply
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate .
This product’s real-time clock battery or coin cell battery may contain perchlorate and may require special handling when recycled or disposed of in California.
28 Chapter 3 Environmental notices
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
Index
Symbols/Numerics
2.4-GHz wireless LAN
A
B
C
Chinese Material Content
D
disposal notices
E electronic hardware and battery
environmental notices 25 equipment disposal notice 25
F
Federal Communications
Commission
cables 2 modifications 2 notice 2
France, 2.4-GHz wireless LAN
G
H
hardware device, identifying 1
headset and earphone volume level
I
Italy, 2.4-GHz wireless LAN
J
Japanese material content
K
L
M
Macrovision Corporation
modem statements
modifications, Federal
N
New Zealand modem
notices
environmental 25 equipment disposal 25
Federal Communications
headset and earphone volume
P
S
Singaporean wireless notice 10
Index 29 ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
T
U
V
W
30 Index
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
ENWW
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Regulatory notices
Safety notices
Environmental notices
Frequently asked questions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following: Do not use this product near water—for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning. Do not use this product to report a gas leak while in the vicinity of the leak. Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component. If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord. Do not plug a modem or telephone cable into the RJ-45 (network) jack.
When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal.
