Entertainment System

Locations and Names of the Controls

1

2

3

4

5

6

20

19

18

7 8

AUX

1 2 3 RPT4 RDM5 6

USB

RESET

9 10 11 12 13 14 15 16

VOLUME

17

1. NFC DETECTION AREA

2. IR REMOTE CONTROL SENSOR

3. 1/2/3 BUTTON

1 TEL / REDIAL BUTTON

2 HANG UP BUTTON

4.ZONE 1/2 BUTTON

5. / BUTTON

6.PLAY/PAUSE BUTTON

RADIO REGION SELECT BUTTON

7.POWER BUTTON

8.STOP BUTTON

AS/PS BUTTON

9.AUX IN SOCKET

10.HEADPHONE SOCKET

11. USB SOCKET

12.BT MODE BUTTON/EQ BUTTON

13.MICROPHONE IN

14.RESET BUTTON

15.INPUT MODE BUTTON/BAND BUTTON

16.5/RANDOM BUTTON

17.VOL KNOB/SEL BUTTON

18.6 BUTTON

19.4/REPEAT BUTTON

20.LCD DISPLAY

PAGE 1

The remote control description

21 20

1

2

3

4

5

6

7

8

9

10

APS

SCAN CLOCK

SEL

AF

MODE

TOP

BAND

INT

PTY

RPT

TA

RDM

CALL

LOG

19

18

17

16

15

14

13

12

11

1.Power button

2.APS button

3.SCAN button

4.CLOCK button

5.BAND button

6.MODE button

7.NUMBER buttons(0~9)

1/PAUSE/PLAY button

2/ INT button

3/RPT button

4/RDM button

8. button

9. MUTE button

10. T-M button

11.TEL button

12. HANG UP/CLEAR button

13. button

14.TA button

15.PTY button

16.- button

17.AF button

18.UP button

19.SEL button

20.+ button

21.DOWN button

Common operation:

1. To turn the unit on/off .

When the unit is power Off, it may be switched On by pressing POWER button.When

the unit is switched On, press and hold POWER button for more than 1 second to

switch the power off.

2. To select function mode

Press INPUT MODE button on the front panel repeatedly to select Tuner,USB(After

inserting a USB storage),BT, F AUX,AV and R AUX mode.

3. To adjust the volume level

Rotate the VOL KNOB on the front panel or press the + or button on the remote control

to adjust volume level during playback.

4. Volume Adjust

Rotate VOL KNOB clockwise to increase to increase volume,rotate anticlockwise to

reduce volume.

PAGE 2

5. To mute or resume sound

Press MUTE button on the remote control to eliminate or resume sound immediately

during playback.

6. To select and adjust the mode of the sound and menu

Press SEL button repeatedly to select the mode of AF ON/AF OFF mode ,TA ON/TA OFF

PTY NEWS/PTY MUSICS,NEWS/POP M,BASS,TRE(treble), LIR(balance),

LOUD OFF/LOUD ON, VOL LAST/VOL DEFA, BEEP ON/BEEP OFF,DX/LOCAL

(in RADIO mode),STEREO/MONO(in RADIO mode),SUBW ON

/SUBW OFF,CLK XX XX, in the sequence and circulation.

In each item, rotate the VOL KNOB to select your desired mode.

1) VOL LAST/VOL DEFA

VOL LAST: The volume level when switching off will be restored with power On.

VOL DEFA: The volume level of the main unit after power on is a constant value.

When selecting VOL DEFA item, press SEL button to display AVOL , then you can pre-set

the constant volume level after power on with VOL control.

2) BEEP ON/BEEP OFF

BEEP ON mode: The beep is generated when any key is pressed.

BEEP OFF mode: The beep sound is disabled.

3) DX/LOCAL

Radio station search mode is divided by this DX/LOCAL switch, which can be used to

control an attenuator in the tuner during search. The detecting level of seek, scan,

auto-memory will be reduced as much as the attenuated level of the tuner. In radio mode,

press the LOC button to change local reception or distance reception. (Note: This button

is only for FM reception. In AM mode, LOC is invalid.)

4) CLK XX XX

When select CLK XX XX mode, Rotate the VOL KNOB to adjust HOUR, press SEL button

for confirmation. With the same means to adjust MINUTE.

7.To select a preset EQ mode

Press and hold BT button on the front panel to select the preset music equalizer curves:

FLAT,CLASSIC,ROCK,CINEMA,EQ OFF. The sound effect will be changed.

8..ZONE 1/2 Button

Pressing ZONE 1 or 2 button will turn on or off the audio source in each of the different

areas which your speakers are connected. “ZONE <1>” or “ZONE <2>” will display on

the LCD once it is selected .

9. To reset unit

When the display is incorrect, or the function buttons are not effective or

sound is distorted, then use a sharp point to press RESET button, that

will make the unit be reset to factory default and re-instate the correct functions.

PAGE 3

Radio Operation

1. FREQUENCY SELECT

In RADIO mode. Press and hold PLAY/PAUSE button for about 5 seconds to

select your desired frequency EUROPE,USA1,USA2 or AUSTRALIA.

2. AM/FM BUTTON

In RADIO mode, press and hold INPUT MODE button on the front panel or briefly press

BND button on the remote control to select your desired radio band of FM1, FM2, FM3,

AM1, AM2 , and the selected band will be displayed on the LCD of the front panel.

3. TUNE/SEEK UP/DOWN

In RADIO mode:

1) Press and hold or button on the front panel or Press and hold

/ button on the remote control to automatically search down/up for a available

station from the current frequency.

2) Press or button on the front panel or press / button on

the remote control to manually search up or down with step by step for your desired station

from the current frequency.

4. APS BUTTON & SCAN BUTTON

In RADIO mode:

1) When pressing and holding APS button on the remote control or

press and hold button on

the front panel

, the radio searches from the lowest frequency and checks the signal strength level

until 1 cycle search is finished.And then the 6 strongest stations are preset to the corresponding preset

number memory bank. The AS operation is implemented in each bank of the selected band.

When the AS operation is finished, it will resume broadcasting

on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)

2) When briefly pressing APS button on the remote control or

press button on the front panel

,

the radio searches for each preset station from the M1. When the field strength level is more than

the threshold level of the stop level, the radio holds at that preset number for a few seconds with

releasing mute, and then searches again.

After finishing a circle of searching, it will stop searching on the M1.

NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.

In AM band, AM1, AM2 is checked one at a time.

3)Press the SCAN button on the remote control to scan the radio frequency. If a valid signal has detected,

the current frequency will be hold and blinking for 5 seconds, then press SCAN again to stop and remain

the current frequency;otherwise, the radio will go on to scan the other radio frequency 5 seconds later.

5. PRESET STATION [ 1-6 ] BUTTONS

In RADIO mode:

1) To memorize the current frequency on the current band, press and hold any one of the six preset

buttons (1-6) .

2) To recall the preset memory on the current band, press one of the preset buttons [1-6] .

6. STEREO/MONO BUTTON

Press ST button on the remote control to select the STEREO or MONO sound mode for

FM band.

PAGE 4

7. LOC BUTTON

1) In RADIO mode, when the signal of the distance radio station are very weak and the receiving

effect is bad during tuning, press LOC button on the remote control to turn off the LOC function,

then tune again for the distance radio station;

2) In RADIO mode, when the signals from the local radio stations are too strong, this could lead

to interference. press LOC button on the remote control to turn on the LOC function,

Re-tune for the local station required.

8. To search for stations with a PTY (PROGRAM TYPE) program

Press and hold SEL button on the front panel or press PTY button on the remote control

to select one of PTY programs:

PTY MUSIC------------------------ PTY NEWS

1. POP M, ROCK M 1. NEWS, AFFAIRS, INFO

2. EASY M, LIGHT M 2. SPORT, EDUCATE, DRAMA

3. CLASSICS, OTHER M 3. CULTURE, SCIENCE, VARIED

4. JAZZ, COUNTRY 4. WEATHER, FINANCE, CHILDREN

5. NATION M, OLDIES 5. SOCIAL, RELIGION, PHONE IN

6. FOLK M 6. TRAVEL, LEISURE, DOCUMENT

When turning on a PTY program, the PTY program and PTY word is flashed on LCD.

After selecting a desired PTY program and no operation for 5 seconds, it will search

for the station of the PTY program. During 1 loop, if the desired station of the PTY

program is not found,it returns to previous normal radio and PTY icon disappears.

9. AF [ALTERNATIVE FREQUENCIES] BUTTON

When pressed briefly, AF switching mode is selected and the state of AF switching

mode is displayed by AF segment in display.

Segment off: AF switching mode off.

Segment on: AF switching mode on, and has RDS information.

Segment flashing: AF switching mode on, but RDS information is not received yet.

When AF switching mode is selected, the radio checks the signal strength of AF all the

time. The interval of checking time of each AFs depends on the signal strength of the

current station, from a few minutes for strong station to a few seconds for weak station.

Every time that new AF is stronger than current station, it switches over to that frequency

for a very short time, and the NEW FREQUENCY is displayed for 1-2 seconds.

Because the mute time of AF switching or checking time is very short, it is almost

inaudible in case of normal program.

During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only

receive and save RDS program.

10. TA [TRAFFIC ANNOUNCEMENT] BUTTON

When TA mode is on(TA is displayed on LCD), it will begin to seek TA station and TA

SEEK will be displayed on LCD for a while.

When traffic announcement is transmitted:

1). If the unit is in SD, USB mode, it will switch to radio mode temporarily.

2). If volume level is below 20, volume level is raised to 20, and returns to its previous

mode and volume level when the traffic announcement is over.

If volume is adjusted during traffic announcement, only the traffic announcement

volume is valid

PAGE 5

USB Operation

1. Pause Playback

During playback, press PLAY/PAUSE button on the front panel or remote

control to pause the playback, press PLAY/PAUSE button again to resume

normal playback.

2. Stop Playback

During playback, press STOP button once to pause the playback, then press the

PLAY/PAUSE button to resume the normal playback;

press STOP button twice to stop the playback, then press PLAY/PAUSE

button to start playback from the beginning of the first chapter/track.

3. Select Chapter with the or button or / Button

Press or button on the front panel or / Button

on the remote control during playback to select the previous or next chapter

to playback.

Note: Press or button or press / Button

multiple times to advance multiple chapters/tracks backward or forward .

4. To scan tracks

During playback, press INT button on the front panel briefly to play the first 10

seconds of each track.

Press INT button again to cancel INT function and retain playing the track

currently selected.

5. To repeat track(s)

During playback, press RPT button briefly to play the current track repeatedly,

and the LCD will display RPT ONE.

Press RPT button twice to play the tracks in the Album repeatedly, and the LCD

will display RPT DIR.

Press RPT button thrice to play the tracks of the albums, and the LCD will display

RPT ALL.

Press RPT button again to cancel RPT function, and the LCD will display RPT OFF.

6. To play tracks in random

During playback, press RDM button briefly to play all tracks in random. Press it

again to cancel RDM function.

7. Tracks search

Press APS button on the remote control, it will activate TRK SEARCH mode.

The LCD will display TRK 0/00/000(deside on the total number of tracks in the

USB stick) and flash the 0 on the biggest digit position. Then press + or button

on the remote control to select number on the flashing digit position from 0 ~ 9,

Press APS button to change the position and with the same means to select

numbers in the other position. After finishing selecting the numbers on all digits

position, press PLAY/PAUSE button to play the track of the selected serial

number.

PAGE 6

Bluetooth Handsfree System

2 ) Select the item of Finding the Bluetooth Device and enter it. After finishing the

finding,it will show the name of the Bluetooth Device FURRION DV3010-XXXX

(where X can be any character A-Z or number 0-9 ) .Select it and enter it, then it will

show an interface that ask you to input a password, input the password 0000 and

enter it. Then it will tell you pair OK.

mobile

(1)Press TEL button to CALL mode, the LCD will display CALL

(2)Input telephone number with number button 0~9.

Short press CLEAR button to cancel the wrongly input number if necessary

(3)Short press TEL button to execute the dialing.

Short press TEL /1 button on the front panel,it will show CALL OUT on

the LCD, then it will execute the dialing.

5.1 Incoming call ringing, short press TEL button on the remote control or 1 button on

the front panel to accept the call.

5.2 To reject Incoming call ringing, short press HANG UP button on the remote control

or 2 button on the front panel to REJECT the call.

5.3 During a phone call, short press HANG UP button on the remote control

or 2 button on the front panel to end the call.

Note: When an incoming call is present the LCD of the DV3010 will display CALL IN.

6. In BT mode, press CALL LOG button to check the LAST DIAL,LAST IN,LAST MISS phone

numbers(press + or button to rotate)

7. To play an audio file from an external Bluetooth device(mobile phone) of the DV3010

After the device has been paired successfully and the DV3010 screen displays

LINK OK

If your mobile device supports A2DP you will then be able to stream music from your Bluetooth device so it can be played by stereo speaker.

You must select on your mobile Bluetooth device to play the audio through Bluetooth.

If your mobile device supports AVRCP then you will be able to control the basic phone

audio output functions by the Wall mount Stereo controls. Eg .

Play Pause .

Note:

During other modes(execpt Bluetooth conversation), press BT MODE button on the

front panel to switch the mode with others.

8.To setup your Stereo using NFC(only support mobile phone with NFC function)

(1) Turn on the NFC function of your mobile phone and make sure the screen is active

and unlocked.

(2) With the NFC detection area of your phone touch with the NFC detection area

of the Stereo, you can connect or disconnect your mobile phone with the Stereo

conveniently.

Note: For the first time pair and connect, it will ask you to input a password.

The password is “0000”.

PAGE 8

Installing the unit

*

Before finally installing the unit, connect the wiring temporarily and make sure

the unit and the system work properly.

*Fix the unit with screw according to following diagram.

SCREW

PLASTIC SHELL

OF THE FRONT PANEL

SCREW

1 . Remove plastic shell of the front panel from the unit.

2. Fix the unit with 4 pieces # 8 pan head self tapping screw.

3. Put back plastic shell of the front panel to the unit.

PAGE 9

Wiring Diagram

IR REMOTE JACK

AV IN AV OUT

SUBWOOFER OUT

ANTENNA

Wiring connecting socket view

AUDIO IN WIRING CONNECTING SOCKET

10

11

12

7

8

9

PIN NO

1

2

COLOR

GREY

GREY/BLACK

3

4

5

6

WHITE

WHITE/BLACK

GREE/BLACK

GREE

PURPLE/BLACK

PURPLE

BLUE

NONE

RED

BLACK

FRONT

FRONT

FRONT

FRONT

REAR

REAR

REAR

REAR

FUNCTION

RIGHT SPEAKER

RIGHT SPEAKER

LEFT SPEAKER

LEFT SPEAKER

LEFT SPEAKER

LEFT SPEAKER

(

(+)

RIGHT SPEAKER

RIGHT SPEAKER

AUTO ANTENNA

MEMORY B+

GROUND

-

(+)

(

(+)

(

)

( -

-

)

)

(+)

)

PAGE 10

Specification

GENERAL

Supply Voltage DC 12V

Current Consumption Max.10A

Power Output 4x 25W RMS

Number of channels 2 STEREO channels.

Unit Dimensions (L X W X H): 200x110.5x105(mm)

FM SECTION

Frequency range 87.5Mhz - 108Mhz (Europe)

87.5 Mhz - 107.9Mhz(U.S.A.)

87.5 Mhz - 108Mhz(Australia)

Effective sensitivity 3uV.

I.F Frequency 10.7MHz.

AM SECTION

Frequency range 522Khz - 1620Khz(Europe)

530khz - 1710Khz(U.S.A.)

522 Khz - 1710Khz(Australia)

Effective sensitivity 40dB

I.F Frequency 450KHz

Preamp Output 2 V Output

USB PLAYBACK

System MP3 audio system

Frequency characteristics 20Hz -100Hz <=5 dB

10KHz-20KHz <=5 dB

Signal to noise (USB) 50dB [1KHz]

FCC Notice:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

---Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Note: It must not be collocated or operated in conjunction with any other antenna or transmitter.