Samsung Electronics A3LML1650 LaserPrinter User Manual

PDF

Dokument

Oglas

Paper Specifications

Overview

This printer accepts a variety of media, such as cut-sheet paper (including up to 100 % recycled fiber content paper), envelopes, labels, transparencies and custom-size paper.

Properties such as weight, composition, grain and moisture content are important factors affecting printer performance and output quality. Paper that does not meet the guidelines outlined in this manual can cause the following problems:

• Poor print quality

• Increased paper jams

• Premature wear on the printer, requiring repairs.

Notes:

• Some paper may meet all of the guidelines in this manual and still not produce satisfactory results. This might be the result of improper handling, unacceptable temperature and humidity levels, or other variables over which Samsung has no control.

• Before purchasing large quantities of paper, make sure that the paper meets the requirements specified in this user

CAUTION: Using paper that does not meet that stated specifications may cause problems for the printer, requiring repairs. Repairs made necessary by the use of paper not specified in this manual are not covered by the Samsung warranty or service agreements.

2 S

PECIFICATIONS

Paper Specifications

Supported Sizes of Paper

Tray 1 or Optional Tray 2

Letter

Dimensions a

8.5 X 11 in. (216 X 279 mm)

Weight Capacity b

Executive

Legal

B5 (JIS)

210 X 297 mm (8.3 X 11.7 in.)

7.3 X 10.5 in. (191 X 267 mm)

8.5 X 14 in. (216 X 356 mm )

16 to 28 lb Bond

(60 to 105 g/m 2 )

550 sheets of

20 lb Bond

(75 g/m 2 ) paper

182 X 257 mm (7.2 X 10 in.)

Folio 216 X 330 mm (8.5 X 13 in.) a. The printer supports a wide range of media sizes. See “Printing on Card Stock or Custom-Sized Media” on page 4.17.

b. Capacity may vary depending on media weight and thickness, and environmental conditions.

Multi-Purpose Tray Dimensions a Weight Capacity b

Minimum Size (custom) 90 X 148 mm (3.5 X 5.83 in.)

Maximum Size (custom) 216 X 356 mm (8.5 X 14 in.)

60 to 163 g/m 2 Bond

(16 to 43 lb )

100 sheets of

75 g/m 2 Bond

(20 lb) paper

Transparency

Labels c

Envelopes

Same minimum and maximum paper sizes as listed above.

Thickness:

.10 X .14 mm

(0.0039 X 0.0055 in.)

20 typical

Thickness:

.10 X .14 mm

(0.0039 X 0.0055 in.)

25 typical up to 90 g/m 2

(16-24 lb) up to 10 a. The printer supports a wide range of media sizes. See “Printing on Card Stock or Custom-Sized Media” on page 4.17.

b. Capacity may vary depending on media weight and thickness, and environmental conditions.

c. Smoothness - 100 to 250 (Sheffield)

Note: You may experience some paper jams when using any media with a length of less than

148 mm (5.83 in.). For optimum performance, make sure you are storing and handling the paper correctly. Please refer to “Printer and Paper Storage Environment” on page A.6.

PECIFICATIONS A.

Paper Specifications

Guidelines for Using Paper

For best results, use conventional 90 g/m 2 (24 lb) paper. Make sure the paper is of good quality, and free of cuts, nicks, tears, spots, loose particles, dust, wrinkles, voids, and curled or bent edges.

If you are unsure of what type of paper you are loading (such as bond or recycled), check the label on the package of the paper.

The following problems with paper can cause print quality deviations, jamming, or even damage to the printer.

Symptom

Poor print quality or toner adhesion

Problems with feeding

Dropout, jamming, curl

Increased gray background shading

/printer wear

Excessive curl problems with feeding

Problem with Paper

Too moist, too rough, too smooth, or embossed; faulty paper lot

Stored improperly

Too heavy

Too moist, wrong grain direction or short-grain construction

Cutouts or perforations Jamming, damage to printer

Problems with feeding Ragged edges

Solution

Try another kind of paper, between 100 ~ 250 Sheffield,

4 ~ 5 % moisture content.

Store paper flat in its moistureproof wrapping.

Use lighter paper, open the rear output tray.

• Open the rear output tray.

• Use long-grain paper.

Do not use paper with cutouts or perforations.

Use good quality paper

Notes:

• Do not use letterhead paper that is printed with low-temperature inks, such as those used in some types of thermography.

• Do not use raised or embossed letterhead.

• The printer uses heat and pressure to fuse toner to the paper. Make sure that any colored paper or preprinted forms use inks that are compatible with this fusing temperature (200 °C or 392 °F for 0.1 second).

4 S

PECIFICATIONS

Paper Specifications

Category

Acid Content

Caliper

Curl in Ream

Cut Edge Conditions

Fusing Compatibility

Grain

Moisture Content

Smoothness

Specifications

5.5 ~ 8.0 pH

.094 ~ .18 mm (3.0 ~ 7.0 mils)

Flat within 5 mm (.02 in.)

Cut with sharp blades with no visible fray.

Must not scorch, melt, offset, or release hazardous emissions when heated to 200 °C (392 °F) for .1

second.

Long Grain

4 % ~ 6 % by weight

100 ~ 250 Sheffield

Paper Output Capacity

Output Tray

Top output (Face-down) tray

Rear output (Face-up) tray

Capacity

250 sheets of 20 lb bond (75 g/m 2 ) paper

100 sheets of 20 lb bond (75 g/m 2 ) paper

PECIFICATIONS A.

Paper Specifications

Printer and Paper Storage Environment

Ideally, the printer and paper storage environment should be at or near room temperature, and not too dry or humid.

Remember that paper absorbs and loses moisture rapidly.

Heat works with humidity to damage paper. Heat causes the moisture in paper to evaporate, while cold causes it to condense on the sheets. Heating systems and air conditioners remove most of the humidity from a room. As paper is opened and used, it loses moisture, causing streaks and smudging.

Humid weather or water coolers can cause the humidity to increase in a room. As paper is opened and used it absorbs any excess moisture, causing light print and dropouts. Also, as paper loses and gains moisture it can distort. This can cause paper jams.

As a result, paper storage and handling are as important as the paper-making process itself. Paper storage environmental conditions directly affect the feed operation.

Care should be taken not to purchase more paper than can be easily used in a short time (about 3 months). Paper stored for long periods may experience heat and moisture extremes, which can cause damage. Planning is important to prevent damage to a large supply of paper.

Unopened paper in sealed reams can remain stable for several months before use. Opened packages of paper have more potential for environment damage, especially if they are not wrapped with a moisture-proof barrier.

The paper storage environment should be properly maintained to ensure optimum printer performance. The required condition is 20 ° to 24 °C (68° to 75 °F), with a relative humidity of

45 % to 55 %. The following guidelines should be helpful when evaluating the paper’s storage environment:

• Paper should be stored at or near room temperature.

• The air should not be too dry or too humid (due to the hygroscopic properties of paper).

• The best way to store an opened ream of paper is to rewrap it tightly in its moisture-proof wrapping. If the printer environment is subject to extremes, unwrap only the amount of paper to be used during the day’s operation to prevent unwanted moisture changes.

6 S

PECIFICATIONS

Envelopes

Paper Specifications

Envelope construction is critical. Envelope fold lines can vary considerably, not only between manufacturers, but also within a box from the same manufacturer. Successful printing on envelopes depends upon the quality of the envelopes. When selecting envelopes, consider the following components:

• Weight: The weight of the envelope paper should not exceed

90 g/m 2 (24 lb) or jamming may occur.

• Construction: Prior to printing, envelopes should lie flat with less than 6 mm (0.25 in.) curl, and should not contain air.

• Condition: Envelopes should not be wrinkled, nicked, or otherwise damaged.

• Temperature: You should use envelopes that are compatible with the heat and pressure of the printer.

• Size: You should only use envelopes within the following size ranges.

Multi-Purpose

Tray

Minimum

90 X 148 mm

(3.5 X 5.83 in.)

Maximum

216 X 356 mm

(8.5 X 14 in.)

Notes:

• Use only the Multi-Purpose Tray to print envelopes.

• You may experience some paper jams when using any media with a length less than 148 mm (5.83 in.). This may be caused by paper that has been affected by environmental conditions. For optimum performance, make sure you are storing and handling the paper correctly.

Please refer to “Printer and Paper Storage Environment” on page A.6.

PECIFICATIONS A.

Paper Specifications

Envelopes with

Double Side Seams

Double side-seams construction has vertical seams at both ends of the envelope rather than diagonal seams. This style may be more likely to wrinkle. Be sure the seam extends all the way to the corner of the envelope as illustrated below.

Correct

Incorrect

Envelopes with

Adhesive Strips or

Flaps

Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal must use adhesives compatible with the heat and pressure in the printer. The extra flaps and strips might cause wrinkling, creasing, or even jams and may even damage the fuser.

Envelope Margins

The following gives typical address margins for a commercial

#10 or DL envelope.

Type of Address

Return address

Delivery address

Minimum

15 mm (0.6 in.)

51 mm (2 in.)

Maximum

15 mm (0.6 in.)

89 mm (3.5 in.)

Notes:

• For best print quality, position margins no closer than 15 mm (0.6 in.) from the edges of the envelope.

• Avoid printing over the area where the envelope’s seams meet.

Envelope Storage

Proper storage of envelopes helps contribute to print quality.

Envelopes should be stored flat. If air is trapped in an envelope, creating an air bubble, then the envelope may wrinkle during printing. See “Printing on Envelopes” on page 4.12.

8 S

PECIFICATIONS

Paper Specifications

Labels

CAUTIONS:

• To avoid damaging the printer, use only labels recommended for laser printers.

• To prevent serious jams, always use the Multi-Purpose Tray to print labels and always use the rear output tray.

• Never print on the same sheet of labels more than once and never print on a partial sheet of labels.

When selecting labels, consider the quality of each component:

• Adhesives: The adhesive material should be stable at

200 °C (392 °F), the printer’s fusing temperature.

• Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets with spaces between the labels, causing serious jams.

• Curl: Prior to printing, labels must lie flat with no more than

13 mm (.5 in.) of curl in any direction.

• Condition: Do not use labels with wrinkles, bubbles, or other indications of separation.

See “Printing on Labels” on page 4.14.

Transparencies

Transparencies used in the printer must be able to withstand

200 °C (392 °F), the printer’s fusing temperature.

CAUTION: To avoid damaging the printer, use only transparencies recommended for use in laser printers.

See “Printing on Transparencies” on page 4.15.

PECIFICATIONS A.

Appendix

B B

If you have a USB (Universal Serial Bus) port enabled on your computer, and if your computer is running Windows 98, you can connect your ML-1650 series printer to the USB chain of devices.

This appendix provides information on the following topics:

◆ Installing the Printer Software

◆ Frequently Asked Questions About USB

Installing the Printer Software

If you have a USB (Universal Serial Bus) port enabled on your computer, and if your computer is running Windows 98, you can connect your ML-1650 series printer to the

USB chain of devices.

Note: Connecting the printer to the USB port of the computer requires a certified

USB cable. You will need to buy the USB 1.0 compliant cable.

1. Install PCL driver

To operate your printer with Windows PC, you must install the

PCL printer driver. Place the CD-ROM in the CD-ROM drive and perform the instructions on page 2.10.

2. Connect printer with

USB cable and install USB driver

1 Make sure that both the printer and computer are turned

ON .

2 Plug one end of the USB cable into the USB port on the printer.

➝ To PC

3 Plug the other end into the USB port on the computer.

4 The Add New Hardware Wizard dialog box appears. Click

Next .

SING

OUR

RINTER WITH A

USB C

ABLE B.

Installing the Printer Software

5 Check Search for the best driver for your device and click

Next .

6 Check CD-ROM drive and click Browse , then choose x:\1650\Eng (or the desired language code, see page

D.2.) \USB (where x is the drive letter for the CD-ROM drive).

7 Click Next . The USB driver will be installed.

8 Follow the instructions on the screen to complete the installation.

2 U

SING

OUR

RINTER WITH A

USB C

ABLE

Installing the Printer Software

3. Set your PC printer port

1 From the Start menu, select Settings , then select Printers .

2 Select the ML-1650 Series PCL 6 printer icon in the

Printers folder.

3 Select Properties from the File menu.

4 Click the Details tab. Select SSUSB: (ML-1650) in the

Print to the following port box. Click OK . The setup is now completed.

SING

OUR

RINTER WITH A

USB C

ABLE B.

Frequently Asked Questions About USB

Universal Serial Bus (USB) makes it easy to connect devices to your computer without having to open your PC. USB uses a standard port and plug combination for connecting devices like printers, modems, scanners, and digital cameras. It also offers the benefit of being able to easily add, remove, and move devices.

Because USB is a relatively new technology, we recommended using a parallel printing connection. However, USB is an option to customers who want to print from Windows 98, Macintosh using a USB cable. If your computer’s USB port is enabled and properly setup, you can connect your printer to it or to a chain of USB devices via a USB cable.

1 In Windows 98, select Start ➝ Settings ➝ Control Panel .

2 Double-click the System icon.

3 Click the Device Manager tab.

4 Click the plus (+) icon before the Universal Serial Bus

Controller item.

If you see a USB host controller and a USB root hub listed, USB is properly enabled. If you have multiple hubs on the USB chain, try connecting your printer to a different hub or to another USB device. Also, make sure the cable connections are firm. (USB hubs are hardware devices into which you can plug multiple USB cables.)

If you do not see these devices listed, refer to your computer’s documentation or contact the manufacturer for more information on enabling and setting up USB. Remember, you can always use a parallel cable to connect your printer’s parallel port to your computer. (If you decide to switch to a parallel cable connection, you may need to remove and reinstall the printer software.)

4 U

SING

OUR

RINTER WITH A

USB C

ABLE

Frequently Asked Questions About USB

Can other users on my USB chain print to my ML-1650 series printer?

Yes. Windows 98 allows you to “share” your printer using software settings on your computer. After others on the USB chain have installed the printer software for your specific printer, they can print to your shared printer.

After I install my printer, why isn’t my ML-1650 series printer assigned to an LPT printer port in the Print dialog box of my software application?

USB uses a different naming convention for USB devices. After the printer has been installed, you see SSUSB:(your printer name) instead of LPT .

How can I increase printing speed and quality?

When operated on a USB chain, your printer may become slower if other USB devices are being used while you’re printing.

For optimal print performance, avoid using other devices in the

USB chain while printing.

SING

OUR

RINTER WITH A

USB C

ABLE B.

Appendix

C C

Your printer supports Macintosh systems with a built-in USB interface or 10/100 Base-TX network interface card. When you print a file from Macintosh, you can use the PCL driver to support your printer’s major printing features. You can also use

PostScript driver by installing the PPD file.

Topics included in this appendix are:

◆ Macintosh Installation

◆ Using PCL Driver

◆ Using PS Driver

Macintosh Installation

System Requirements

To use your ML-1650 Series printer and its software with a

Macintosh, your system should have:

Macintosh Hardware

Requirement

• One of the following Macintosh models:

-Power Macintosh series (for network connection only)

-Power Macintosh G3, G4

-iMac series

-iBook series

• USB interface or network interface (for network connection only)

Macintosh System

Requirement

• For network connection: System 7.6 or later

• For USB connection: System 8.6 or later

Printer Hardware

Requirement

• PS DIMM (for PS driver user only.)

• Network interface (for network connection only.)

SING

OUR

RINTER WITH

ACINTOSH C.

Macintosh Installation

Connecting To Macintosh

You can connect the printer to your Macintosh using the USB interface or network interface.

USB Connection

USB cable is not provided in your printer. Purchase a certified

USB 1.0 compliant cable.

1 Turn off the printer and computer.

2 Hold the USB cable so the icon faces up and connect it to your printer’s USB connector.

3 Connect the other end of the cable to an available USB port on your Macintosh computer. If you have any connecting problems, please refer to your computer documentation.

Note: If you are using a USB hub, connect the printer’s cable to the first tier of the hub or the printer may malfunction. If the printer doesn’t work with the hub, connect it directly to the USB port.

2 U

SING

OUR

RINTER WITH

ACINTOSH

Macintosh Installation

Network Connection

If you have a printer with 10/100Base-TX network interface card installed, you can connect to an Ethernet network. Use a Category 5 twisted pair cable with RJ-45 connectors for

10/100Base-T Ethernet.

1 Plug one end of the network cable into the twisted-pair connector on the back of the printer.

2 Connect the other end to the network hub.

Note: You must configure your printer for the network.

For information about configuring your printer, refer to the Network User’s Guide.

SING

OUR

RINTER WITH

ACINTOSH C.

Macintosh Installation

Installing Software for Macintosh

1 Turn on your computer and printer.

2 Insert the CD-ROM which came with your printer into the CD-

ROM drive.

3 Double-click Samsung ML-1650 on your Macintosh desktop.

4 Select the correct language, then click Continue .

5 The Samsung Laser Printer Installer opens. Select installation type. The installer provides two options for software installation:

• Easy Install (recommended method): This option loads

PPD, installs PCL driver.

• Custom Install : This option allows you to choose which components will be installed. If you want to use the PCL driver, you must install it. If you want to use PostScript driver, you must install the PPD file.

6 Click Install .

7 After installation is complete, click Quit .

4 U

SING

OUR

RINTER WITH

ACINTOSH

Using PCL Driver

If you want to use your printer’s PCL driver on your Macintosh computer, take the following steps:

Choosing PCL Driver

1 From the Apple menu, select Chooser .

2 From the left pane of the Chooser window, click

SAMSUNG PCL . Then the Samsung PCL driver name will appear in the right pane of the Chooser window.

3 Click the Samsung PCL driver, and close the Chooser window.

4 You see the message box indicating that you have changed your current printer. Click OK .

5 A Samsung PCL printer icon will be created on your desktop.

Printing from a Macintosh

When you print with a Macintosh, you need to check the printer software setting in each application you use. Follow these steps to print from a Macintosh:

1 Open a Macintosh application and select a file you want to print.

2 Open the File menu, and click Page Setup ( Document

Setup in some applications). You will see the Page Setup dialog box.

SING

OUR

RINTER WITH

ACINTOSH C.

Using PCL Driver

3 Choose your paper size, orientation, paper type and other options and click OK .

Choose Watermark if you want to add a watermark to each page in your document to emphasize its purpose or indicate how it should be handled. For details on the watermark option, see page 5.21.

6 U

SING

OUR

RINTER WITH

ACINTOSH

Using PCL Driver

4 Now open the File menu and click Print . You see the main printer settings dialog box.

5 Choose the number of copies and indicate which pages you want to print. For advanced printing features, select the desired option. For details, see page C.8.

Select the desired option for advanced printing features.

6 Click Print when you are finished checking your settings.

SING

OUR

RINTER WITH

ACINTOSH C.

Using PCL Driver

Advanced Printing

The Page Setup dialog box contains five categories of page setup properties. Listed below is the name of each property.

-Darkness/Quality

-Layout

-Color

-Background Printing

-Paper Source

Figures below display each property in the Page Setup dialog box.

Darkness/Quality

Select print darkness.

Select print resolution.

Layout

Select the number of pages you want to print on one sheet of paper. The pages will appear decreased in size and arranged on the sheet.

8 U

SING

OUR

RINTER WITH

ACINTOSH

Color

Using PCL Driver

Select grayscale mode.

Grayscale

Black&White

Background Printing

Turns background printing on or off.

Paper Source

Click it if optional Tray 2 is installed.

Select a priority for your print job in the queue of jobs waiting to print, by clicking one of the following:

• Normal to print in the order the job is received.

• Urgent to print before any

Normal priority job.

• Print at: to print at the specific time you enter in the day and time in the fields to the right.

• Put document on hold to hold the print job in the print queue until you are ready to release it.

Select the corresponding paper source. If Auto Select is set, the printer automatically selects the print media according to the following order: Multi-Purpose

Tray, Tray 1, Tray 2 (option).

SING

OUR

RINTER WITH

ACINTOSH C.

Using PS Driver

If you want to use the PS driver which were installed on your Macintosh computer, you must install the PPD file to access your printer features and allow the computer to communicate with your printer.

PPD file installation method is different for USB connection and the network connection.

Installing PPD file on the USB-connected Macintosh

1 Follow the instruction as described on page C.4 to install the PPD file on your computer.

2 Open the Macintosh HD and double-click Apple Extras .

3 Double-click Apple LaserWriter Software .

4 Double-click Desktop Printer Utility .

5 Select LaserWriter 8 , and select Printer (USB) in the list box. Then click OK .

6 Click the Change button in the USB Printer Selection section. The name of your printer appears in the list.

7 Click ML-1650 , then click OK .

8 Click the Auto Setup button in the PostScript Printer

Description (PPD) File section.

If Auto Setup does not work properly, click Select PPD and choose Samsung ML-1650 Series .

9 When the setup is completed, click the Create button.

1 0 Click the Save button to save ML-1650 as a desktop printer.

10 U

SING

OUR

RINTER WITH

ACINTOSH

Using PS Driver

Installing PPD file on the network-connected Macintosh

1 Follow the instruction as described on page C.4 to install the PPD file on your computer.

2 From the Apple menu, select Chooser .

3 Click LaserWriter 8 (the PostScript driver provided with your Macintosh). The name of your printer appears in the list. Select SEC000xxxxxxxxx from the printer box

(where the xxxxxxxxx varies depending on each of the products.).

4 When the setup is completed, you see your printer icon is created as a desktop printer.

If Auto Setup does not work properly, click Select PPD

Printing from a Macintosh

Follow these steps to print from a Macintosh:

1 Open a Macintosh application and select a file you want to print.

2 Open the File menu, and click Print . You see the main printer settings dialog box.

3 Choose the number of copies and indicate which pages you want to print. For advanced printing features, select the desired option.

4 Click Print when you are finished checking your settings.

SING

OUR

RINTER WITH

ACINTOSH C.

Appendix

D D

While your printer is primarily a Windows printer, you can also print from a DOS software program using the Remote Control

Panel utility provided in the ML-1650 series CD-ROM.

Topics included in this Appendix are:

◆ About Remote Control Panel for DOS

◆ Installing the Remote Control Panel for DOS Users

◆ Selecting Print Settings

About Remote Control Panel for DOS

DOS users have access to many printer features through specific DOS printer drivers; however, many software manufactures do not develop printer drivers for their software programs. The Samsung ML-1650 series printer provides the

DOS software control panel for improved printer control when

DOS printer drivers are not available or when certain print settings are not available through DOS software programs.

Notes:

• ML-1650 series printer’s Remote Control Panel for DOS can be used when the printer is connected via the parallel interface.

• The ML-1650 series printer’s Remote Control Panel is not a printer driver. It should be used to set print settings that are not available through DOS sof tware programs. Printer drivers are supplied by the manufacturers of your DOS sof tware programs.

If your DOS sof tware program does not include a printer driver for your Samsung printer, contact the manufacturer of the sof tware program or use one of the alternate printer drivers.

RINTING FROM

DOS A

PPLICATIONS D.

Installing the Remote Control

Panel for DOS Users

Language Codes

Code

DEU

ENG

ESN

FRN

ITA

KOR

Language

German

English

Spanish

French

Italian

Korean

The Remote Control Panel utility is provided on the printer software CD-ROM. If you do not have a CD-ROM drive, refer to

Appendix G, “Installing Software from Diskette” for information on obtaining printer software on diskettes.

To install the DOS Remote Control Panel:

1 Insert the printer software CD-ROM or RCP diskette in your computer’s drive.

2 At the DOS prompt, make a directory that you want to use the DOS software and change to that directory.

3 From the floppy drive, type:

COPY x:\*.* (where x is the floppy drive designator)

From the CD-ROM drive, type:

COPY x:\1650\xxx\RCP\*.* (where x is the CD-ROM drive designator and xxx is the designator for your language. See the list on the left for the designator for each language).

Then press Enter .

Selecting Print Settings

When you are running DOS, you can use this Remote Control

Panel to select print settings that may not be available from some DOS programs. Typically, duplicate print settings that are selected from a DOS software program override print settings selected in the ML-1650 Series Remote Control Panel.

Note: Af ter you change the RCP settings, you must send it to the printer by pressing S nd

2 P

RINTING FROM

DOS A

PPLICATIONS

Selecting Print Settings

To access the Remote Control Panel

1 Make sure that the Remote Control Panel is in your path statement. You can check your path by typing PATH and pressing Enter . If the Remote Control Panel directory is not in your path, you will have to change to the default directory

C:\DOSUTIL to start the program.

2 At the DOS prompt, type DOSRCP and press Enter .

After the Remote Control Panel appears, you can activate its selections in one of two ways:

• With the mouse – Move the mouse to position the pointer on the desired selection, then click the left mouse button.

• With the keyboard – Press the key that corresponds to the highlighted letter in the selection name.

The Remote Control Panel allows you to access the following features:

PRINTING

• Paper Size sets the paper size.

• Paper Source sets the default paper source.

• Copies sets the number of copies printed for each page.

• Orientation determines how the output is printed on the page.

• Top Margin sets the top margin of the print material.

• Left Margin sets the left margin of the print material.

• Auto CR sets how the printer performs a carriage return.

• Quality determines the print resolution.

RINTING FROM

DOS A

PPLICATIONS D.

Selecting Print Settings

CONFIG

• Power Save determines the length of time the printer waits after a job is printed before it goes to a reduced power state. If the printer is used frequently, select OFF which keeps the printer ready to print with the minimum warm-up time. This uses more electricity to keep the printer warm and ready to print.

• Econo Mode determines the toner quantity the printer should use when printing. If set to ON , the printer conserves toner when printing. The default value is OFF , which provides 100% usage.

• Auto Continue determines what action the printer should take when a manual feed print job is sent to the printer and there is no paper in the Multi-Purpose Tray. If set to ON , the printer will pick up the paper from the standard Tray 1 or optional Tray 2 after fifteen seconds. Otherwise, the printer will wait for you to load paper in the Multi-Purpose Tray.

• Jam Recovery determines what action the printer should take when a paper jam occurs. When set to OFF , the printer does not reprint a page that has jammed. When set to ON , the printer keeps the image in memory for a printed page until the printer signals that the page has successfully printed. The printer reprints all jammed pages.

JOB

• Timeout determines the amount of time (in seconds) the printer will wait before printing the last page of a print job that does not end with a command to print the page or a formfeed character. Valid range is 0 to 300 seconds.

• Paper Type provides the printer with information about the type of paper to be used for a print job. For the best result, set this to the paper type you loaded in the paper tray in the printer. When using the plain paper, set this to Default .

• SRT Mode makes the printer optimize the print quality to 1200 dpi image quality.

4 P

RINTING FROM

DOS A

PPLICATIONS

Selecting Print Settings

TEST

• Configuration Page prints the configuration sheet. A list of the user default settings, the installed options, and the amount of printer memory available prints.

• Demonstration Page prints the demonstration page. It shows the printer features and specifications.

PCL5e

• Typeface allows you to select the desired typeface. This setting is ignored when the software application specifies a font.

• Symbol Set determines the symbol set. A symbol set is a set of alphabetic and numeric characters, punctuation, and special symbols used when printing with a selected font.

• Pitch sets the font pitch (only if you have selected a scalable monospaced font). Pitch refers to the number of fixed-space characters in a horizontal inch of type.

• Lines Per Page sets the number of lines that print on each page. The setting can range from 5 to 128 lines per page.

• Point Size sets the font point size (only if you have selected a scalable typographic font). Point size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch. You can select point sizes from 4.0 to 999.75 in increments of 0.25 points.

• Courier determines the courier font type: Regular or Dark.

• Font List prints the font list showing all the fonts available for

PCL emulation.

PS3

• Font List prints the font list showing all the fonts available for

PostScript (only available when the PostScript option is installed).

• PS Error determines what action the printer should take when an error occurs in PS interpreter. When set to OFF , the printer does not print error information when error occurs in PS interpreter. When set to ON , the printer prints error information when error occurs in PS interpreter.

RINTING FROM

DOS A

PPLICATIONS D.

Appendix

E E

If you want to use the PostScript driver provided with your system CD-ROM or diskettes to print a document, use the information on this Appendix.

Topics included in this Appendix are:

◆ Setting Up Your Printer with PS Option

◆ Installing PPD Files

◆ Accessing the PS Printer Driver Features

Setting Your Printer with the PS Option

If you want to use the PostScript driver to print a document, your printer should have:

• PS DIMM

For instructions on installing the printer options, see Appendix

H, “Printer Options.”

Installing PPD Files

PPDs, in combination with the PostScript driver, access the printer features and allow the computer to communicate with the printer. An installation program for the PPDs is provided on the ML-1650 CD-ROM.

Notes:

• Installing the PostScript printer driver may require the use of the operating system files on the original CD-ROM or diskette that came with your system.

• If you have a PostScript 3 driver and want to use it, you must install the PostScript 3 PPD which is also provided on the ML-

1650 series CD-ROM.

1 Before installing PPD files, make sure that the printer and the PC are properly connected with parallel, USB, or optional network interface. For information on:

• Connecting with parallel interface, see page 2.7.

• Connecting with an USB interface, see Appendix B, “Using

Your Printer with a USB Cable.” To use the USB interface, you must also install the USB port driver.

• Connecting with an optional network interface, see

Appendix F, “Using Your Printer on a Network.”

SING

INDOWS

OST

CRIPT

RIVER E.

Installing PPD Files

2 Insert the CD-ROM shipped with your printer into your CD-ROM drive.

If the CD-ROM drive does not automatically run:

Select Run from the Start menu, and type x:\cdsetup.exe

in the Open box (where x is the drive letter for the CD-ROM drive), then click OK .

3 When the opening screen appears, select the appropriate language.

4 Click Install the Samsung Software-II on your PC

(PostScript) .

5 Click on HaveDisk , click Browse , then choose:

• for Windows 9x, x:\Eng (or the desired language code.

See page D.2.) \ps\Win95_98\level 2

• for Windows NT 4.0, x:\Eng (or the desired language code.

See page D.2.) \ps\WinNT\level 2

• for Windows 2000, x:\Eng (or the desired language code. See page D.2.) \ps\Win2000\ where x is the drive letter for the CD-ROM drive, then click OK .

6 Follow the instructions on the screen to complete the installation.

2 U

SING

INDOWS

OST

CRIPT

RIVER

Accessing the PS Printer Driver Features

Certain printer features are not available in this PS driver. Refer to “Printer Driver Features” on page 2.12.

The printer automatically switches between PS and PCL printer languages depending on the driver you have selected.

Opening the Printer Properties Window

The properties window for the Windows PostScript printer driver can be opened from the Printers folder or an application.

To open the properties window from the Printer folder:

1. Click the Windows Start button.

2. Select Settings then Printers to open the Printers window.

3. Select Samsung ML-1650 Series PS .

4. Click the right mouse button and select Properties to open the properties window.

To open the properties window from inside an application:

1. From the File menu, select Print to open the Print dialog box.

2. Make sure that Samsung ML-1650 Series PS is selected in the Name drop-down list.

3. Click Properties to open the properties window.

SING

INDOWS

OST

CRIPT

RIVER E.

Appendix

F F

If you work in a networked environment, the printer can be shared by other users on the network.

This appendix provides information on the following topics:

◆ About sharing the Printer on a Network

◆ Setting Up a Locally Shared Printer

◆ Setting Up a Network-Connected Printer

About Sharing the Printer on a Network

If you work in a networked environment, you can connect the ML-1650 series printer to your network.

Locally Shared

You can connect the printer directly to a selected computer

(called the “host computer”) on the network. The printer can then be shared by other users on the network through a Windows 9x or NT 4.0 network printer connection.

Network-Connect

If an option network card was installed on your printer (see page H.5 for information on installing the option network card in your printer).

Printing Across a Network

Whether the printer is locally connected or network connected, you need to install the ML-1650 series printer software on each computer that will print documents to the

ML-1650 series printer.

SING THE

RINTER ON A

ETWORK F.

Setting Up a Locally Shared Printer

Setting Up Host Computer

1 Start Windows.

2 From the Start menu, select Control Panel , and doubleclick on the Network icon.

3 Check the File and Print Sharing box, then click OK .

Close the window.

4 Click Start and select Printers from Settings , then double-click your printer name.

5 Select Properties in the Printers menu.

6 Click the Sharing tab, then check the Shared As box.

Fill in the Shared Name field, then click OK .

Setting Up Client PC

1 Right-click Start , and select Explorer.

2 Open your network folder in the left column.

3 Right-click the shared name, and select Capture Printer

Port .

4 Select the port you want, check the Reconnect at log on box, then click OK .

5 From the Start menu, select Settings , then Printers .

6 Double-click your printer icon.

7 From the Printers menu, select Properties.

8 Press the Details tab, select the printer port, then click

OK .

2 U

SING THE

RINTER ON A

ETWORK

Setting Up a Network-Connected Printer

To use ML-1650 series printer as a network printer, you must install an optional network card in your printer. See page H.5 for information on installing network card.

After the network card is installed, you must set up your printer as a network printer using the documentation and

Samsung SyncThru software provided with the network card.

SING THE

RINTER ON A

ETWORK F.

Appendix

G G

If you need to install the printer software on a system that does not have a CD-ROM drive, use the instruction on this appendix to create the software diskettes and install the printer software from the diskettes.

This appendix provides information on the following topics:

◆ Making Installation Diskettes

◆ Installing Software from Diskettes

Making Installation Diskettes

If you do not have a CD-ROM drive but you have access to another computer with a CD-ROM drive, you can copy software installation files from your printer software CD-

ROM onto floppy diskettes, and then use the diskettes instead of the CD-ROM to install the software.

You can make installation diskettes for PCL6 printer driver,

USB driver for Windows 98, PostScript Printer Description

(PPD) file and Remote Control Panel utility independently.

Make sure that you have several formatted diskettes ready, and then follow these steps:

1 Insert the CD-ROM shipped with your printer into the

CD-ROM drive. Installation will start automatically.

If the CD-ROM drive does not automatically run:

Select Run from the Start menu, and type x:\cdsetup.exe

in the Open box (where x is the drive letter for the CD-ROM drive), then click OK .

2 When the opening screen appears, select the appropriate language.

3 Click Make your own Diskette set of software.

NSTALLING

OFTWARE FROM

ISKETTES G.

Making Installation Diskettes

Shows the number of disks required to copy the selected component.

4 The Copy to Floppy dialog box appears.

Select the desired components you want to copy to the diskette from the Select box. You can select PCL6 Printer

Driver, PostScript Printer Description file, USB Port Driver and RCP.

Select the floppy disk drive you will use to insert the diskette.

Select the floppy drive you will use.

Select the component you want to copy.

Shows the path of the selected component.

2 I

NSTALLING

OFTWARE FROM

ISKETTES

5 Click Copy all disk images .

If you want to copy a portion of the selected component, select the disk you want to copy in the Disk Images window, then click Copy selected disk image .

6 When prompted, insert a blank, formatted diskette into the floppy drive, and click Yes to copy the first diskette.

For multiple diskettes, when the first diskette is finished, you are prompted to insert disk 2.

Make sure you label each diskette in order of creation PCL printer driver, disk 1 of 3, etc.

Making Installation Diskettes

7 If you have more than one disk, insert the next disk and click Yes . Repeat this step for a third disk if necessary.

8 When copying to diskettes has been completed, click

Close in the Copy to Floppy dialog box. Then click Exit in the SAMSUNG PRINTER SETUP dialog box.

Installing Software from Diskettes

The instructions to install a PCL 6 printer driver, PPD file and

RCP are same. Take the following steps:

1 Insert the first diskette (if you have more than are selected software diskette) which contains the desired installation software; PCL 6 printer driver, USB driver, PPD file or RCP.

2 From the Start menu, select Run .

3 Type A:\setup.exe in the Open box and click OK . (if your floppy drive is not A , substitute the correct letter.)

4 Follow the on-screen instruction to complete the installation.

NSTALLING

OFTWARE FROM

ISKETTES G.

Appendix

H H

Your printer is a full-featured laser printer that has been optimized to meet most of your printing needs. Recognizing that each user may have different requirements, however,

Samsung makes several options available to enhance the printer’s capabilities.

This appendix provides information on the following topics:

◆ Precautions

◆ Memory and PostScript DIMMs

◆ Network Interface Card

◆ Paper Tray 2

Precautions

DISCONNECT THE POWER CORD:

Never remove the printer control board while the printer is plugged in.

To avoid the possibility of electrical shock, always disconnect the power cord when installing or removing ANY internal or external printer option.

DISCHARGE STATIC ELECTRICITY:

The control board and internal printer options (Memory DIMM,

PS DIMM, Network interface) are sensitive to static electricity.

Before installing or removing an internal option, discharge static electricity from your body by touching something metal, such as the metal back plate on any device plugged into a grounded power source. If you walk round before finishing the installation, discharge any static electricity once again.

RINTER

PTIONS H.

Memory and PostScript DIMMs

Additional printer memory and the PostScript option are provided on DIMMs (single in-line memory modules). This procedure is applicable to either option.

Turn the printer power off and unplug all cables from the printer.

Remove the two screws on the rear of the printer, then remove the control board cover.

Locate the PS DIMM slot (the lower slot on the left as shown) and the memory

DIMM slot (the upper slot) on the control board. They are not interchangeable.

• To install the memory DIMM, continue with Step 4.

• To install the PS DIMM, go to Step 5.

2 P

RINTER

PTIONS

Memory

PS DIMM

Memory and PostScript DIMMs

Hold the memory DIMM so that the

2 are aligned with the slot as shown, and insert the DIMM all the way into the upper slot labeled DRAM MODULE at a 90(Straight) degrees angle.

Hold the PS DIMM so that the notch 1 with the slot as shown, and insert the

DIMM all the way into the lower slot labeled FLASH-ROM MODULE at a

90(Straight) degrees angle.

Reconnect the power cord and turn the printer on.

Note: For PostScript driver installation and usage information on a Macintosh system, refer to Appendix C, “Using Your Printer with a Macintosh.” For PS printing on a Windows system, refer to Appendix E, “Using Windows PostScript Driver.”

RINTER

PTIONS H.

Network Interface Card

Review the precautions on page H.1 and then follow this procedure to install the Network card option in your printer.

Unpack the network printer card. You should find the following items.

Network card

(PortThru)

User’s guide

CD-ROM

(SyncThru)

Brackets Screws

Two brackets come with the network card. Select the long bracket and attach it to the network card with two screws provided.

Turn the printer power off and unplug all cables from the printer.

Remove the two screws on the back of the printer, then remove the control board cover. See the figure on page H.2.

Remove the two screws, then remove the plate.

4 P

RINTER

PTIONS

Network Interface Card

Align the connector on the network card with the connector on the control board.

Push the card firmly into the connector until it is completely inserted in place.

Tighten the two screws as shown.

Tighten the two screws, then replace the plate.

Reconnect the power cord and printer cable, then turn the printer on.

Note: For information on configuring and using the printer on a network environment, refer to the documentation provided with the network card option.

RINTER

PTIONS H.

Paper Tray 2

You can increase the paper handling capacity of your printer by installing the optional Tray 2. The optional paper tray consists of two components; the support unit and paper tray .

Note: Be sure you check the lla be using the optional Tray 2. (For use with ML-1650 Series only)

Turn off the printer and unplug all cables from the printer.

Observe the location of the support unit’s connector and tabs.

tap connector

Label tap

Align the printer with the support unit and lower it into place on the tabs and connector.

support unit paper tray

Load paper in Tray 2. For information on loading paper in the tray, see page 2.4.

6 P

RINTER

PTIONS

Paper Tray 2

Reconnect the cables, then turn the printer on.

Note: To print from Tray 2, you must configure the printer driver from your application prior to printing. To access the printer driver, see page 5.2.

Click. If this box is checked, you can select Tray 2 in the

Paper Source drop-down list.

RINTER

PTIONS H.

Appendix

I I

You can use Samsung ML-1650 Series printer in Linux environment.

This appendix provides information on the following topic:

◆ Linux Driver Installation

Linux Driver Installation

This Linux driver is designed for the Samsung ML-1650

Series printer and supports Linux Red Hat 6.0 or higher and

Intel Linux. If your Linux version is not included, this driver might not work properly.

• Install Setup Script file configuration a. /cdrom/linux/install.sh

b. /cdrom/linux/ssprt.db

c. /cdrom/linux/readme.txt

Installation

To install the driver, open the x terminal screen and take the following steps:

1. Mount the CD-ROM drive.

Note: To mount the CD-ROM drive, you must be a super user or must be authorized to mount the CD-ROM by the super user. If you fail to mount the CD-ROM drive, ask the system administrator.

To mount the CD-ROM drive:

1 Insert the Samsung ML-1650 Series CD-ROM into the

CD-ROM drive.

2 Mount the CD-ROM drive under a directory like /mnt in order to access the files on the CD-ROM:

>mount -t iso9660 /dev/cdrom /mnt/cdrom

2. Install setup script.

For details on installing the setup script, refer to the

/cdrom/linux/readme.txt

file.

Add the driver to the printer list by typing in:

/cdrom/linux>install.sh

(or)

/cdrom/linux>./install.sh

(if the path of the current working directory is not determined.)

SING

OUR

RINTER IN

INUX I.

Linux Driver Installation

3. Set up the printer filter.

To set up:

1 Run printtool at x terminal.

2 To add the printer driver, click the Add button.

3 In the Add a Printer Entry window, decide the printer type you will use. Select Local Printer if you have a PCconnected printer.

4 Click the OK button.

5 If the Info button appears, ignore it, then click the OK button.

6 The Edit xxxx Entry window opens (where xxxx is the printer type you have selected at step 3).

If you are not an advanced user, do not change the

Names/Spool Directory/File Limit in Kb/Printer

Device option.

7 Click the Select button in the Input Filter to access filter setup.

8 Select Samsung Printer PCL5e Compatible for the

Printer Type item. Then select the default resolution and paper size.

9 To save the setting, press the OK button.

1 0 In the Edit xxxx Entry window, press the OK button to complete the printer driver installation.

1 1 You can find that the printer driver is added to the driver window. Select Quit from the PrintTool menu.

2 U

SING

OUR

RINTER IN

INUX

INDEX

Numeric

2-sided printing 5.7

B

booklet printing 5.11

C

cancel, print job 5.5

Cancel/Reprint button 3.2

cardstock, print 4.17

clean, printer 6.4

clean sheet, print 7.6

components 1.3

configuration page, print 7.6

control panel buttons 3.1

lights 3.4

custom-sized media, print 4.17

D

Data light 3.4

Demo button 3.3

demo page, print 2.8, 7.6

diskette, make, install software G.1

DOS RCP see remote control panel driver, PCL6 access 5.1

features 2.12

install 2.10

remove 2.13

E

envelopes, print 4.12

error messages 7.22

F

face-down tray 4.4

face-up tray 4.4

features 1.1

G

graphic mode 5.20

graphic properties 5.18

H

halftone, setting 5.20

I

install

Linux driver I.1

PPD file for windows E.1

PPD file for macintosh C.4

printer software, parallel cable 2.9

printer software, USB cable B.1

remote control panel for DOS D.2

software from diskette G.3

toner cartridge 2.2

NDEX I

INDEX

J jam see paper jam

L labels, print 4.14

letterhead, print 4.16

load, paper in the multi-purpose tray 4.8

in tray 1 or the optional tray 2 2.4

using the manual feed 4.10

Linux driver I.1

Macintosh connecting network interface C.3

connecting USB interface C.2

install PCL driver C.4

install PPD file C.10

solving common problems 7.25

system requirements C.1

manual 2-sided printing 5.7

manual duplexing 5.7

manual feed loading paper 4.10

paper source setting 5.3

Manual light 3.5

memory, option H.2

multi-purpose tray loading paper 4.8

paper source setting 5.3

multiple pages on one sheet, print 5.10

N network interface install network card H.5

set up a locally shared printer F.2

sharing the printer on a network F.1

n-up printing 5.10

O option memory DIMM H.2

network interface card H.5

paper tray 2 H.7

PS DIMM H.2

orientation 5.3

output tray, select 4.4

rear 4.4

top 4.4

overlay, print 5.24

P paper acceptable size and capacities 4.2, A.3

choose 4.1

guidelines 4.3, A.4

load 2.4, 4.6

specifications A.2

storage environment A.6

paper jam, clear 7.7

in the optional Tray 2 7.14

input area 7.10

inside the printer 7.12

output area 7.7

tips for avoiding paper jams 7.15

II I

NDEX

INDEX

(continued) paper level indicator 4.6

Paper light 3.5

paper orientation, setting 5.3

paper out, indicator 7.22

paper source, setting 5.3

paper tray change paper size in tray 2.5

load paper 2.4

optional Tray 2 H.7

paper type, setting 5.3

parallel, connection 2.7

PCL 6 driver see driver, PCL 6 poster, print 5.16

postscript level 3 emulation 1.2

access windows PS driver E.3

install PPD file for Macintosh C.4, C.10

install PPD file for windows E.1

problem solving 7.27

print media see paper print quality problem, solving back of printouts dirty 7.20

background scatter 7.19

black pages 7.20

character voids 7.21

checklist 7.16

curl or wave 7.20

dropouts 7.17

grey background 7.18

horizontal stripes 7.21

light or feded print 7.16

loose toner 7.21

misformed characters 7.19

page skew 7.19

toner smear 7.18

toner specks 7.17

vertical lines 7.17

vertical repetitive defects 7.18

wrinkles or creases 7.20

printer light patterns 7.22

Q quality, problems 7.16

printer driver see driver, PCL 6 printer software, install 2.10

printing booklets 5.11

cancel 5.5

cleaning sheet 7.6

configuration page 7.6

demo page 7.6

fitting to a selected paper size 5.15

from windows application 5.1

from DOS applications D.1

general problems, solving 7.2

help 5.5

multiple pages on one sheet 5.10

on a network F.1

on both sides of the paper 5.7

on different paper for first page 5.14

poster 5.16

quality problems, solving 7.16

using page overlay 5.24

using windows PS driver E.1

watermarks 5.21

with macintosh C.1

problem, solving common macintosh problems 7.25

common windows problems 7.24

error messages 7.22

general 7.2

paper jam 7.7

print quality 7.16

PS errors 7.27

Troubleshooting checklist 7.1

PS see postscript level 3 emulation

NDEX III

INDEX

Ready Mode 3.4

rear output tray 4.4

remote control panel install D.2

use D.2

reprint, last page 3.2

resolution 5.19

S setup printer chapter 2 specifications paper A.2

printer A.1

SRT mode 5.19

system error 7.23

T toner cartridge cleaning sheet 6.5

install 2.2

life expectancy 6.1

recycle 6.1

redistribute toner 6.2

save toner 5.6, 6.1

storage 6.1

Toner Save button 3.1. 5.6

top output tray 4.4

transparency, print 4.15

troubleshooting see problem, solving tray 1 see paper tray

U uninstall, driver 2.13

unpacking 2.1

USB cable setup in windows B.1

setup in macintosh C.2

W watermark, print 5.21

IV I

NDEX

Živjo! Sem AI chatbot, posebej usposobljen za pomoč pri Samsung Electronics A3LML1650 LaserPrinter User Manual. Temeljito sem pregledal dokument in vam lahko pomagam najti točne informacije, ki jih potrebujete, ali razložim vsebino na jasen in preprost način. Ne glede na to, ali iščete navodila o določenih funkcijah, korake za odpravljanje težav ali splošno uporabo, lahko zastavite svoja vprašanja. Več podrobnosti kot navedete o svojih pomislekih ali potrebah, natančneje in učinkoviteje vam lahko pomagam!

Pomočnik tipka

Pomočnik je prekinil povezavo. Poskusite znova pozneje.

Izgleda, da ste prišli do dokumenta, ki je napisan v več jezikih, vključno z jezikom, ki ni vaš materni jezik. Uporabite lahko naslednje povezave, da začasno skrijete strani brez jezika, ki ga želite.

Oglas