UAT PGCAD-9711 ADSLAdd-on Card User Manual

Quick Start

ADSL Modm Card

Table of Contents

Congratulations!................................................................................................................1

Step 1 – Know your PC’s Operating System

...............................................................1

Step 2 – Determine your Connection Settings

...........................................................2

Step 3 – Install the ADSL Modem Card

.......................................................................3

Step 4 – Install the Drivers and Make a Connection

.................................................5

Windows 95A ....................................................................................................................6

Windows 95B.....................................................................................................................8

Windows 98, 98SE...........................................................................................................11

Setting the ADSL Configuration...........................................................................13

Making a RFC 1483 or RFC 1577 connection - 95A, 95B, 98, 98SE .................14

Making a RFC 2364 connection - 95A, 95B, 98, 98SE........................................18

Windows 2000 .................................................................................................................19

Setting the ADSL Configuration...........................................................................21

Making a RFC 1483 or RFC 1577 connection - 2000 ..........................................22

Making a RFC 2364 connection - 2000.................................................................24

Windows NT4.0 - RFC 1483 or RFC 1577 ....................................................................25

Setting the ADSL Configuration for RFC 1483 or RFC 1577.............................27

Windows NT4.0 - RFC 2364...........................................................................................28

Setting the ADSL Configuration for RFC 2364...................................................31

Creating a Dial-up Network Connection ......................................................................32

Appendix

Editing your Service Connection ..................................................................................33

Removing Drivers............................................................................................................34

Diagnostic Tools .............................................................................................................35

Trouble Shooting ............................................................................................................37

Connector Pin-out ...........................................................................................................38

LED Functions.................................................................................................................38

System Requirements & Compliance information......................................................39

Copyright & Regulatory Information...........................................................................39

Congratulations!

You are about to accelerate into ADSL technology. Your new ADSL modem card is an internal Asymmetric Digital Subscriber Line (ADSL) PCI modem card, which conveniently plugs into your computer system. The modem connects directly to your telephone line via a standard connector.

This guide is designed to walk you through installation of your ADSL Modem card in the easiest and quickest way possible. Please follow the instructions carefully.

Step 1 – Know your PC’s Operating System

You will need to know the exact version of Microsoft Windows installed in your computer. If you do not know or are unsure, please proceed as follows to determine your version of the Microsoft Operating System.

On your desktop, right -click My Computer . Then select Properties . The version number of the Microsoft Windows Operating System installed in your computer will be displayed on the General tab. Refer to the following table for more detailed information.

Windows OS System Properties Description Release (Microsoft Web)

Win 95A

Win 95B

Win 98

Win 98SE

Win 2000

Win NT

4 00 950A

4.00.950B

4.10.1998

4.10.2222A 2nd Edition

5.00.2195

4.00.1381

Windows 95 OSR1

Windows 95 OSR2

Window 98

Windows 98 2nd Edition

Windows 2000

Windows NT 4.0

If you have questions regarding your PC system and the Microsoft Windows Operating

System, please contact your original PC manufacturer or Microsoft for assistance.

Before Installing the ADSL PCI Modem Card, it is important to verify that the ADSL data port RJ-11 jack is configured so that the center two pins, pins 3 and 4, are used for ADSL data, otherwise the ADSL PCI modem card will not make a proper connection. If the ADSL

1

data port installation uses pins 2 and 5 for data, then a wiring converter will be required. Do not alter or remove a wiring converter if present. Consult with your ADSL service provider regarding a wiring converter or before attempting any wiring changes.

2

Step 2 – Determine your Connection settings

You need to know your PC systems Windows OS and Internet Protocol supplied by your ADSL service provider. Refer to the following chart for your ADSL Driver .

RFC1483

RFC2364

RFC1577

RFC2516

Protocol Selection

!!

Bridged Ethernet over ATM

!!

Point-to-Point Protocol over ATM

!!

Classical Internet Protocol over ATM

!!

Point-to-Point Protocol over Ethernet

ADSL Driver

Selection

RFC1483 RFC2364 RFC1577 RFC2516

Win 95A & 95B

Win 98 & 98SE

Win NT 4.0

Win 2000

1483w95

1483w98

1483nt4

1483w2k

2364w95

2364w98

2364nt4

2364w2k

1577w95 See Note

!

1577w98 See Note

!

1577nt4 See Note

!

1577w2k See Note

!

Note

!

: RFC2516 (Point-to-Point Protocol over Ethernet) is supported by third party developers. See the PPPoE driver supplement for detailed information and installation instructions.

Having determined the ADSL Driver you will be installing, you now need to gather the connection information supplied by your ADSL service provider.

VPI value:_________

VCI value:_________

Framing: !

VC/MUX

!

LLC/SNAP

Mode: !

ANSI T1.413

!

ITU G.lite

!

ITU G.dmt

For RFC 1483 or 2516 For RFC 2364 or 1577

Host:

Domain:

Gateway:

IP Address:

Subnet Mask:

DNS or server address:

User Name:

Password:

Host or IP Address:

3

Step 3 – Install the ADSL modem card

Caution: To avoid possible damage to your modem card, touch the metal chassis of your

PC system to remove static charge from your person, and then remove your ADSL modem card from the protective anti-static bag.

1. Shut down your computer and switch the power off .

2. Unplug the power cord for your computer from the electrical outlet.

3. Remove the cover from your systems chassis (see your PC manufacturer’s manual).

4. Unscrew “slot cover bracket” from an unused PCI (usually white in color) slot.

5. Gently and evenly insert the PCI modem card into your empty PCI slot.

6. Make sure the card is firmly seated, and then secure the card with the bracket screw .

7. Replace the cover of your computer system.

8.

Connect the ADSL/phone line

to the connector port on the modem card and plug the other end of the cable into your ADSL/phone service.

4

Step 4 – Install the drivers and make a connection

You will be installing drivers and then proceeding to make an Internet connection. This process requires you to enter in information as prompted by the Microsoft Installation

Wizard.

NOTE : You may need the Microsoft Windows Operating System installation files (CAB files) to complete the installation. The CAB files are contained in the Microsoft’s system

CD-ROM. Some systems may have already installed the CAB files to the hard drive, but you should have the Microsoft Windows CD-ROM handy just in case.

Proceed now to the installation procedure for the Windows Operating System installed in your computer.

Windows 95A -------------------------------------------------------------------------------Page 6

Windows 95B -------------------------------------------------------------------------------Page 8

Windows 98, 98SE------------------------------------------------------------------------- Page 11

Windows 2000 ------------------------------------------------------------------------------Page 19

Windows NT - RFC 1483 or RFC 1577 -----------------------------------------------Page 25

Windows NT - RFC 2364----------------- -----------------------------------------------Page 28

5

Windows 95A

After installing the ADSL modem card, plug the power cable back into the PC system and turn the power on.

Before you proceed to install drivers you will need to upgrade your Dial-Up

Networking (DUN) application to version 1.3 or above.

The Microsoft DUN is conveniently contained on your ADSL Driver CD-ROM.

1. After restart, the Update Device Driver

Wizard will detect the ADSL modem as a

PCI Network Controller.

CANCEL the

New hardware found window .

2. At your desktop, click Start , and then select Run .

3. The Run window appears. Insert the

ADSL Driver CD , then click on Browse and proceed to locate the ADSL Driver 95

CD-ROM. Then locate and select the

Msdun13.exe

file. The Msdun13.exe

appears in the Open box. Click OK .

4. The Microsoft Dial-Up Networking 1.3

window appears with the message This will install Microsoft Dial -Up

Networking 1.3 for Windows 95. Do you wish to continue?

Click Yes .

5. An End-User License Agreement will appear. To accept, click Yes .

6

6. Back in the Microsoft Dial-Up

Networking 1.3 window. You will be asked: Do you want to restart your computer now?

Click Yes.

7

NOTE : You may need the Microsoft Windows Operating System installation files (CAB files) to complete the installation. The CAB files are contained in the Microsoft’s system

CD-ROM. Some systems may have already installed the CAB files to the hard drive, but you should have the CD-ROM handy just in case.

7. After your computer reboots, the New

Hardware Found window will detect the

ADSL modem card as a PCI Network

Controller.

Select the Driver from disk provided by hardware manufacturer option. Click OK .

8. Insert the ADSL Driver CD-ROM into your systems CD drive.

9. The Install From Disk window appears.

Click Browse to locate the driver on your

CD-ROM for the protocol supported by your ADSL provider: 1483w95,

2364w95, or 1577w95 (The example uses

“D” as the CD -ROM drive letter. Drive letters may vary.) Then click OK .

NOTE : During the installation process you may be asked to insert your

Windows 95 CD. Insert the Windows 95

CD into the CD drive and click OK .

NOTE : If during the file copying process a file is reported as “not found” enter the path with the CD Drive letter and :\Win95 (ex:D:/Win95).

10. You must now set the ADSL configuration. Go to page 13.

8

Windows 95B


6.

Before you proceed to install drivers you will need to upgrade your Dial-Up Networking

(DUN) application to version 1.3 or above. The Microsoft DUN is conveniently contained on your ADSL Driver CD-ROM.

1. After restart, the Update Device Driver

Wizard will detect the ADSL modem card as a PCI Network Controller.

CANCEL the New hardware found window .

2. At your desktop, click Start , and then select Run .

3. The Run window appears. Insert the

ADSL Driver CD , then click on Browse and proceed to locate the ADSL Driver 95

CD-ROM. Then locate and select the

Msdun13.exe

file. The Msdun13.exe

appears in the Open box. Click OK .

4. The Microsoft Dial-Up Networking 1.3

window appears with the message This will install Microsoft Dial -Up

Networking 1.3 for Windows 95. Do you wish to continue?

Click Yes .

5. An End-User License Agreement will appear. To accept, click Yes .

Back in the Microsoft Dial-Up

9

Networking 1.3 window. You will be asked Do you want to restart your computer now? Click Yes.

You may need the Microsoft Windows Operating System installation files (CAB files) to complete the installation. The CAB files are contained in the Microsoft’s system CD-

ROM. Some systems may have already installed the CAB files to the hard drive, but you should have the CD-ROM handy just in case.

7. After your computer reboots, the Update

Device Driver Wizard will detect the

ADSL modem card as a PCI Network

Controller , click Next .

8. Insert the ADSL Driver CD-ROM into you systems CD drive.

9. The Update Device Driver Wizard will appear and indicate that “ Windows was unable to locate a driver for this device ”. Click Other Locations .

10. The Select Other Location window appears. Click Browse to locate the driver on your CD-ROM for the protocol supported by your ADSL provider:

1483w95, 2364w95 or 1577w95

(The example uses “E” as the CD-ROM drive letter. Your drive may have a different letter.) Then click OK .

11. The Update Device Driver Wizard will then find the ITeX ADSL PCI NIC . Click

Finish .

10

NOTE: During the installation process you may be asked to insert your Windows

95 CD-ROM. Insert the Windows 95 CD into the drive and click OK .

NOTE: During the installation process you may be asked to insert your

Windows 95 CD-ROM. Insert the Win95

CD into the drive. Click OK .

NOTE: If during the file copying process a file is reported as “not found” enter the path (CD Drive letter) and :\Win95 (ex.

D:\Win95 )


11

Windows 98, 98SE


1. The Add New Hardware Wizard window will automatically appear to indicate that a

new PCI Network Controller has been found. Click Next .

2. Still in the Add New Hardware Wi zard .

You will be asked “ What do you want

Windows to do?

” Select the Search for the best driver for your device option, then click Next .

3. Insert the ADSL Driver CD into your systems CD-ROM drive.

4. Select Specify a location and click

Browse to locate the driver on your CD-

ROM for the protocol supported by your

ADSL provider: 1483w98 or 2364w98 or

1577w98 (The example uses “D” as the

CD-ROM drive letter. Your drive may have a different letter.) Then click Next .

5. The Add New Hardware Wizard will appear and indicate the ITeX ADSL PCI

NIC has been recognized and will install a new driver. Click Next .

12

6. If prompted to insert your Windows

CD, do so at this time, then click OK.

7. Enter the [CD drive Letter] and then :\Win98 (e.g: E:\Win98 ) and click OK .

8. At the conclusion of the ADSL modem driver installation, the Add

New Hardware Wizard window appears and displays your newly installed ITeX ADSL PCI NIC .

Click Finish.

9. The System Settings Change window appears. For the PC system to set up the ITeX Apollo 2 Drivers , a system Restart is required. Click

Yes .

NOTE : After restarting the system, the Diagnostic Tool icon (See Appendix) is active and monitoring connectivity.


13

1.

WINDOWS 95/98

SETTING THE ADSL CONFIGURATION

FOR RFC 1483/1577/2364

After your PC has rebooted, right -click on the Mapi Icon , and select the

Configuration option .

2. The Configuration window appears.

This is the Network Protocol and

PVC settings section. Enter in the

VPI, VCI, and Framing values supplied by your ADSL service provider.

3. In the Select ADSL Mode section, select the mode(s) recommended by your ADSL service provider. Click on the mode(s) required and then click on

NOTE

: THE SERVICE MODE TYPE

WILL BE ONE OF THE FOLLOWING:

!!

ANSI T1.413 Issue 2

!!

ITU G.992.2 Annex A (G.lite)

!!

ITU G.992.1 Annex A (G.dm

4. The PVC Setup window appears.

Click Yes to restart your PC system and to allow the new changes to take effect.

5. You must now make an ADSL connection.

Proceed to the section for your protocol.

14

Making an ADSL connection

RFC 1483 – Bridged Ethernet over ATM – 95/98

RFC 1577 - Classical Internet Protocol over ATM – 95/98

RFC1483


!!

Go to page 14

RFC1577


!!

Go to page 14

RFC2364


!!

Go to page 18

1. From the Start menu on the tool bar, select Settings , Control Panel , and then double-click on the Network icon.

2. The Network window appears. Select the Configuration tab, scroll the installed network component window and find ITeX ADSLPCI NIC .

15

3. Scroll the installed network component window and select TCP/IP !

ITeX

ADSL PCI NIC. Then click the

Properties button.

4. The TCP/IP Properties window will appear. Select the IP Address tab and then select the Specify an IP Address option. Enter the IP Address and

Subnet Mask settings supplied by your

ADSL provider.

16

5. To setup a new gatew ay, select the

Gateway tab, and then enter the setting in the New Gateway section. Click Add .

6. Select DNS Configuration tab. Select the Enable DNS option.

NOTE: You now need to have available the Host , Domain and DNS settings supplied by your ADSL service provider

7. Enter your host name into Host: box.

8. Enter your domain name into Domain: box.

9. Enter DNS number into DNS Server

Search Order box and click Add . If you have more than one DNS numbers, repeat this step.

10. After setting all the necessary TCP/IP properties, click OK.

17

11. The

OK .

Network window appears. Click

12. The System Setting Change window appears. You will be asked if you want to restart your computer. Click Yes .

Congratulations, you are done. Your ADSL Internet connection is established!

18


RFC 2364 - Point-to-Point Protocol over ATM – 95/98

1. Double-click on the ITeX

PPPoA icon that appears on your desktop.

2. The Connect To window appears.

Enter the User Name and Password supplied by your Internet service provider (ISP). Then click Connect .

3. The Connecting to My Connection window appears. The message

Logging on to network confirms a valid connecting process.

4. The Connection Established window appears. Internet service is now established. Click Close and then the Diagnostic tool icon will appear on the task bar.


19

Windows 2000


1. After installing the ADSL modem card, power on the PC system. After start -up, the Found New Hardware Wizard will appear. Click Next .

2. Still in the Found New Hardware

Wizard , select the Search for a suitable device. option. Click Next .

3. Next you will be prompted for software drivers. Select Specify a location. Click

Next .

4. Insert the ADSL Driver CD into the systems CD-ROM drive. Click Browse to locate the driver on your CD-ROM for the protocol supported by your ADSL provider: 1483w2K or 2364w2K or

1577w2K (The example uses “D” as the

20

CD-ROM drive letter. Your drive may have a different letter.) Click OK .

5. The Found New Hardware Wizard will then find the ITeX ADSL PCI NIC, click

Next .

6. The Digital Signature Not Found window appears. You will be asked; Do you want to continue instal lation? Click Yes .

7. The Found New Hardware Wizard will prompt that Windows has finished installing the software for this device .

Click Finish.

NOTE: You may be asked if you want to restart your computer, if so click Yes.

If you are not asked, you need to restart your computer manually at this time.


21

WINDOWS 2000

SETTING THE ADSL CONFIGURATION

FOR RFC 1483/1577/2364

1. After your PC has rebooted, right -click on the Mapi Icon , and select the



This is the Network Protocol and




NOTE : The service mode type will be one of the following:

!!

ANSI T1.413 Issue 2

!!


!!

ITU G.992.1 Annex A (G.dmt)

.



5. You must now make an ADSL connection. Proceed to the section for your protocol.

RFC1483

RFC1577

RFC2364


!!

Go to page 22


!!

Go to page 22


!!

Go to page 24

22


RFC 1483 – Bridged Ethernet over ATM – 2000

RFC 1577 - Classical Internet Protocol over ATM – 2000

1. Double-click My Computer , Control Panel , and then Network and Dial -up

Connections .

2. The Network and Dial-up Connections window appears. Right -click on the Local

Area Connection, and then click on propert ies.

3. The Local Area Connection window appears. Click on Internet Protocol

(TCP/IP) , then click on Properties .

23

4. The Internet Protocol (TCP/IP) window appears. Under the General tab, enable Use the following IP address . The default settings for IP configurations will turn from gray to clear . Enter in the IP address , Subnet

Mask , and Default Gateway supplied by your ADSL service provider. Click

OK .

5. The previous General Tab window appears. Click OK .

24


6. The Network and Dial-up Connection window appears. CLOSE this window and your connection is complete.

25


RFC 2364 - Point-to-Point Protocol over ATM – 2000

1. Double-click on the ITeX PPPoA icon that appears on your desktop.

2. The Connect My Connection window will appear. Enter your User Name and

Password sup plied by your ADSL service provider. You are now ready to make a network connection. Click Dial .

3. The Connection complete appears, click OK .

window

Congratulations, you are done. Your ADSL connection is established!

26

Windows NT4.0

RFC 1483 – Bridged Ethernet over ATM

RFC 1577 - Classical Internet

Protocol over ATM

1. On your desktop, double-click My

Computer , and then double-click

Control Panel .

2. In the Control Panel window, doubleclick the Network icon. The Network window appears. Select the Adapters tab and then click Add .

3. The Select Network Adapter window appears. Click Have Disk .

4. Insert ADSL Driver CD-ROM into your systems CD drive.

5. The Insert Disk window appears. Click



ADSL provider: 1483NT4 or 1577NT4

(The example uses “d” as the CD-ROM drive letter. Your drive may have a different letter.) Click OK .

6. The Select OEM Option window will find the ITeX ADSL PCI NIC , Click

OK .

27

7. The Network window will appear.

Click the Adapters tab to verify that the ITeX ADSL PC NIC has been found. Click on the Protocols tab and verify that the ADSL Management and Monitor Interface is present.

NOTE: To review the Network window properties at any time, rightclick the Network Neighborhood icon and select Properties .

NOTE: If no previous network devices have been installed, then the Network

Neighborhood icon will not be present on your desktop. To open the Network window, double-click My Computer then Control Panel then Network .

8. The Microsoft TCP/IP Properties window appears. Enter in the IP

Address , Subnet Mask and Default

Gateway supplied by your ADSL service provider. Click OK .

9. The Network Settings Change window appears. You must now re-start your computer for the settings to take effect.

Click Yes .

28


WINDOWS NT 4.0

SETTING THE ADSL CONFIGURATION FOR

RFC 1483 OR RFC 1577









!!

ANSI T1.413 Issue 2

!!


!!

IT U G.992.1 Annex A (G.dmt)


Click Yes to restart your PC system and to allow the new changes to take effect

29

5. Now you must create a Dial-up Connection. Please go to page 32.

30

Windows NT4.0

RFC 2364 – Point to Point Protocol over ATM

1. On your desktop, double-click My

Computer , and then double-click Control

Panel .

2. In the Control Panel window, doubleclick the Network icon. The Network window appears. Select the Adapters tab and then click Add .

3. The Select Network Adapter window appears. Click Have Disk .

4. Insert the ADSL Driver CD-ROM into your systems CD drive.

5. The Insert Disk window appears. Click



ADSL provider: 2364NT4 (The example uses “d” as the CD-ROM drive letter.

Your drive may have a different letter.)

Click OK .

6. The Select OEM Option window will find the ITeX ADSL PCI NIC , Click OK .

31

7. The Setup Message window appears.

Click OK .

8. The Windows NT Setup window appears. Insert your NT4.0 CD-

ROM into the PC system CD drive, and type in “D:\i386” Click

Continue .

9. The Add RAS Device window appears.

Click on the “Scroll arrow” to locate

ISDN1-itexwana . Then click OK .

10. The Remote Access Setup window appears. Click Continue .

11. The Network window will appear. Click the Adapters tab to verify that the ITeX

ADSL PC NIC has been found. Click on the Protocols tab and verify that the

ADSL Management and Monitor

Interface is present. Click on the

Services tab to verify that the Remote

Access Service is present. Then click

Close .

NOTE: To review the Network window properties at any time, right -click the

Network Neighborhood icon and select

Properties .

NOTE: If no previous network devices

32

have been installed, then the Network

Neighborhood icon will not be present on your desktop. To open the Network window, double-click My Computer then

Control Panel then Network .

12. The Network Settings Change window appears. You must now re-start your computer for the settings to take effect.

Click Yes .

13. You must now set the ADSL configuration for RFC 2364. Go to page 31.

33

WINDOWS NT 4.0

SETTING THE ADSL CONFIGURATION FOR

RFC 2364









!!

ANSI T1.413 Issue 2

!!


!!

ITU G.992.1 Annex A (G.dmt)



5. You must now create a Dial-up Network Connection. Please go to page 32.

34

WINDOWS NT4.0

CREATING A DIAL-UP NETWORK CONNECTION

2. Double-click on the ITeX PPPoA icon that appears on your desktop.

2. The Dial -Up Networking window appears and prompts for the phone number of the dial-up server. Unless instructed to enter a phone number by the ADSL service provider , enter zero

“0”. Click Dial .

3. The Connect to MyDialUpServer window appears. Enter the User name,

Password and Domain supplied by your

ADSL service provider. Click OK .

NOTE : If this screen persists and a connection logon error is reported, confirm that the correct User name and

Password are entered and try the connection again. Also verify that the connection address is correct.

4. The Connection Complete window is displayed at the completion of a successful Dial-Up logon. Choose a disp lay behavior and click OK to close.


35

Editing Your Service Connection

Service Connection

1. To view or edit the ADSL connection service address, right-click the Diagnostic

Tool icon (located on the Taskbar), and select the Configuration option.

2. The PVC Setup (Permanent Virtual Connection) window displays the connection service address. Click Close to exit window.

3. To edit the connection service address , select and enter the VPI and VCI address in the field shown and click PVC Setting .

4. To accept a Connection Address that has been changed ( restart the PC System), click Yes .

NOTE: A PC system restart will begin once the connection address change is accepted.

IP Configuration

1. This section includes the IP configuration specifics for Windows NT4.0. The NT 4.0 windows are slightly different from those of Windows 95 /98. Other than minor screen differences, the process for editing the IP address settings is the same for

Windows NT 4.0 and Windows 95/98.

2. At your desktop, double-click My Computer , then double-click Control Panel to view the contents of the control panel. In the Control Panel window, double-click the Network icon.

Note : The Network window shortcut is a right -click on the Network

Neighborhood icon on your desktop, and then a left -click on Properties .

3. Select the Protocols tab of the network window. Select TCP/IP Protocol and click

Properties .

4. Select the IP address option and note that the IP Address and Subnet Mask regions will turn from gray to active .

5. Enter the IP Address (e.g. 192.168.4.39) and Subnet mask (e.g. 255.255.255.0).

6. Enter the Default Gateway in this window, and then enter the Host Name and

Domain.

NOTE : Please refer to your ADSL service provider.

To enter the Domain search

(DNS) entries, click Add, then enter the address. Click Add to save the address.

Repeat the process for additional DNS entries.

Click OK to update the changes.

36

Removing Drivers

Windows 95, 98 WINDOWS NT4.0

WINDOWS 2000

1. On the desktop, click the

START Menu on the Task

Bar.

2. Select Programs . The system window appears.

3. Select the ITeX Tab, and then click on the Un-Installer Tab.

Note: For W95-98-NT4, an Uninstall Finished windows message appears. Click

Yes to restart your system and confirm changes.

37

Diagnostic Tools

The diagnostic tool icon allows the user to monitor the ADSL connectivity, setup the service connection address, and run diagnostic tests. The Diagnostic Tools icon is displayed on the task bar as shown. By positioning the mouse cursor over the icon, the upstream and downstream rates are displayed.

Maximum receiving rate

Maximum transfer rate

The Diagnostic Tool icon consists of two lights side by side. The left light indicates data is being transmitted whereas the right light indicates data is being received. The state of the connection can be determined as follows:

Color Code Description

Red, Red No ADSL connectio n and No ADSL handshaking. Check your cable connections.

ADSL handshaking – Connection not established. Precursor to Black,

Yellow or

Yellow/Blac

Black, establishing an ADSL connecting.

ADSL connection established – no data traffic or idle connection

Green ,

Green,

Green

?

ADSL connection established – NIC is receiving data (TX/off,

ADSL connection established – NIC is transmitting data (TX/on,

ADSL connection established – NIC is transmitting and receiving data

(TX/on, RX/on)

NIC is disconnected or a driver problem exists.

On the Diagnostic Tool icon, located on the right hand side of the status bar, right-click the icon to display the menu, then click Open . The ADSL

Diagnostic Tool window ap pears on your desktop.

The four tabs of the Diagnostic Tools are ADSL

Status , Diagnostic , ADSL Statistics and

Configuration .

ADSL Status window displays the current state of the ADSL connection, including the current ADSL

State, ADSL protocol in use, and the Net Data Rates for upstream and downstream data.

NOTE: ADSL protocols supported by the ADSL drivers are T1.413, G.dmt and G.lite. The protocol must be supported also by the ADSL equipment located at the central office.

ADSL Statistic window keeps tabs on errors that might affect overall system performance. The counts are reset whenever the PC system is restarted.

38

Re-training Count tracks the number of ADSL connections performed. Due to unexpected line condition changes, the drivers can re-train the connection causing the Re-training Count total to increment. The Diagnostic Tool icon will flash yellow while reconnecting.

ADSL implements Reed Solomon (RS) error checking:

FEC Count tracks the forward error correction count.

CRC Count tracks the accuracy of correcting data errors over each 17msec.

ATM HEC Count (header error check) errors are recorded as an indication of ATM packet accuracy.

As a measure of packet transfer performance, the

Packet Errors are counted and tracked against the

Click Run Diagnostics to run t he diagnostic program that will test PC functionality and report the status. A warning message pops up that the

ADSL service will disconnect before performing the diagnostic test. If connected to the Internet at this time, disconnect any Dial-up sessions. Click Yes to begin the diagnostic program or click No to exit diagnostic program . The diagnostic program performs a brief hardware check and displays the hardware status

The Diagnostic window is used to verify the ADSL modem card functionality. Running the Diagnostic program will disconnect the NIC from the ADSL line. Close all Dial-up sessions and close all files before running the Diagnostic program. Product

Information (e.g. driver revisions) is displayed by clicking the Product Info tab.

Product Information lists the versions of the

Diagnostic Tools and the driver version. The DLL version describes the software being used by both the drivers and Diagnostic Tool software.

39

Connector Pin-out

The ADSL modem card is equipped with a RJ-11 jack for connection to the ADSL data port. The center two pins, pins 2 and 3, are used for ADSL data. For the card to make a proper

ADSL connection, the installed ADSL data port should also use pins 2 and 3 for data. If the ADSL data port installation uses pins

1 and 4 for data, then a wiring converter will be required. Do not alter or remove the wiring converter if present. Consult with your

ADSL provider before attempting any wiring changes.

LED functions for the Apollo 3

Green LED on tom

Green LED on Top

Status Signals

PWR On 0.5s, Off 0.5s

On

SYNC On 0.25s, Off 0.25s

Description

Modem initialized, idle mode (disconnect)

Power Supply OK

Modem Connecting

(On 0.25s, Off 0.25s) x 2,

Modem Connected

Off 0.5s

Yellow LED on Top DATA On TX or RX ATM data transmission smission,

Off no data

(in showtime status)

Red LED on Bottom ERR On 0.25s on any CRC r

All 4 LED All On

ATM data transmission

(in showtime status)

Driver not installed or

40

System Requirements & Compliance Certification

System Requirements

! !

IBM PC/AT or compatible

! !

Pentium 100Mhz or faster

! !

30Mbytes available hard disk space or more

! !

2x CD-ROM drive or better

! !

32Mbyte available system memory or more

Power Requirements

! !

0.75A Max @ +5V

?

5%, 0.1A max @

?

12V,

?

5%

Environmental Requirements

! !

Operating Temperature: 0

?

C to 70

?

C with airflow

! !

Non-operating Temperature: -10

?

C to 85

?

C

! !

Operating Humidity: 10% to 90% non-condensing

! !

Non-operating storage humidity: 5% to 95% non-condensing

Compliance Certification

! !

UL 1950

! !

CE approved

! !

FCC Part 15 Class B

Copyright & Regulatory Information

Copyright

?

2000, Integrated Telecom Express, Inc. All rights reserved.

This manual and software described in it are copyrighted with all rights reserved. This manual may not be copied, in whole or in part, without written consent. All product names are trademarks and or registered trademarks of their respective companies.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure:

!!

Reorient or relocated the receiving antenna.

!!

Increase the separation between the equipment and receiver.

!!

Connect the equipment into a different outlet circuit from than the receiver.

!!

Consult an experienced radio/TV technician for help.

CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment.

41

No results