Edge-Core SAF51003I User Manual

The Edge-Core SAF51003I Network Appliance Platform is a compact and powerful server designed for a wide range of applications, including network security, SD-WAN, and edge computing. With its Intel Atom C3000 series processor, up to 32GB of DDR4 memory, and multiple storage options including M.2 SSDs and a 2.5" HDD, the SAF51003I delivers high performance and reliability. It also features a rich set of I/O ports, including 8x 1000BASE-T RJ-45 LAN ports, a dedicated 1000BASE-T RJ-45 WAN port, and a 1000BASE-T RJ-45 DMZ port, making it ideal for connecting to various network devices.

PDF

Dokument

Reklama

SAF51003I

Network Appliance Platform

U s e r M a n u a l

www.edge-core.com

User Manual

SAF51003I

Network Appliance Platform

E052018-CS-R01

How to Use This Guide

This guide includes detailed information on the Network Appliance Platform, including how to install components and maintain the system. To deploy this device effectively and ensure trouble-free operation, you should first read the relevant sections in this guide so that you are familiar with all the features.

Who Should Read this Guide?

This guide is for system technicians who are responsible for installing, maintaining, and troubleshooting this Network Security Platform. The guide assumes a basic working knowledge of server appliance hardware, LANs (Local Area Networks), and the Internet Protocol (IP).

How this Guide is

Organized

The organization of this guide is based on the device’s main components. An introduction and initial configuration information is also provided.

The guide includes these sections:

■ Section I “Getting Started” — Includes an introduction to the device’s hardware features.

■ Section II “Installation Procedures” — Includes how to install or replace device hardware components.

■ Section III “System Configuration” — Includes information on how to configure

BIOS settings.

■ Section IV “Appendices” — Includes information on troubleshooting device problems and safety and regulatory statements.

– 3 –

How to Use This Guide

Conventions

The following conventions are used throughout this guide to show information:

Note: Emphasizes important information or calls your attention to related features or instructions.

Caution:

Alerts you to a potential hazard that could cause loss of data, or damage the system or equipment.

Warning: Alerts you to a potential hazard that could cause personal injury.

Revision History

This section summarizes the changes in each revision of this guide.

May 2018 Revision

This is the first revision of this guide.

– 4 –

Section I

Section II

How to Use This Guide 3

Contents 5

Figures 8

Tables 9

Getting Started 10

1 System Overview 11

Introduction 12

Front Panel Features

Rear Panel Features

System Board Layout

System Block Diagram

System Specifications

2 System Components

Power Supply

System Memory

M.2 Solid-State Drives (SSDs)

Mini PCIe Slot

System Battery

16 Installation Procedures

3 Chassis Installation

General Installation Guidelines

Installation Precautions

Installing the Server Appliance on a Desktop

– 5 –

20

21

Contents

Section III

Section IV

Appliance Cooling Requirements

Removing the Top Cover

4 Server Connections

Grounding the Device

Connecting Power and Powering On

Connecting to the Console Port

Connecting to 1000BASE-T Network Ports

System Configuration 31

5 BIOS Setup Access

BIOS Introduction

Accessing the BIOS Setup Menu

BIOS Setup Utility Keyboard Commands

6 BIOS Settings

Main Menu

Advanced Menu

IntelRCSetup 39

Security menu 40

Administrator Password

User Password

BOOT Menu

Save and Exit Menu

36

32

25 Appendices 44

A Troubleshooting 45

Power Supply

POST and Boot Problems

Cooling and Fans

Network Connections

B Installing the Intel Driver 47

– 6 –

C LED Control Utility

D Safety and Regulatory Information

Contents

48

49

– 7 –

Figures

Figure 1: SAF51003I Front Panel Features

Figure 2: SAF51003I Rear Panel Features

Figure 3: System Board

Figure 4: System Block Diagram

Figure 5: AC/DC Power Adapter

Figure 6: DIMM Slot

Figure 7: M.2 SSD Slot on System Board

Figure 8: Mini PCIe Slot

Figure 9: System Battery

Figure 10: Installing the Appliance on a Desktop

Figure 11: Removing the Top Cover

Figure 12: Grounding the Device

Figure 13: Connecting Power to the Server

Figure 14: Connecting to the Console Port

Figure 15: Connecting to 1000BASE-T RJ-45 Ports

Figure 16: Access to BIOS Settings

Figure 17: BIOS Setup Menu Access

Figure 18: BIOS Main Menu

Figure 19: BIOS Main Menu

Figure 20: BIOS Advanced Menu

Figure 21: BIOS Intel RC Setup

Figure 22: BIOS Security Menu

Figure 23: BIOS Boot Menu

Figure 24: BIOS Save and Exit Menu

Figure 25: Status LEDs

Figure 26: LED Control Utility

– 8 –

Tables

Table 1: SAF51003I Specifications

Table 2: Console Cable Wiring

Table 3: Maximum Twisted-Pair Copper Cable Lengths

Table 4: RJ-45 Port Status LEDs

Table 5: BIOS Setup Utility Commands

– 9 –

Section I

Getting Started

This section provides an overview of the Network Appliance Platform and introduces some basic concepts.

This section includes these chapters:

■ “System Overview” on page 11

■ “System Components” on page 16

– 10 –

System Overview

This chapter includes the following sections:

■ “Introduction” on page 12

■ “Front Panel Features” on page 12

■ “Rear Panel Features” on page 12

■ “System Board Layout” on page 13

■ “System Block Diagram” on page 14

■ “System Specifications” on page 15

– 11 –

Chapter 1

| System Overview

Introduction

The SAF51003I Network Appliance Platform is an open server appliance based on standard Intel® x86 communications hardware. The system includes internal eMMC and M.2 SSD disk drives, all contained within a desktop form-factor.

Front Panel Features

Figure 1: SAF51003I Front Panel Features

1 2 3 4 5

Power Status LED

Custom-defined Status LEDs

WAN Port Status LEDs

Rear Panel Features

Figure 2: SAF51003I Rear Panel Features

1 2

DMZ Port Status LED

LAN Ports 1-8 Link Status LEDs

3 4

1000BASE-T RJ-45 LAN Ports

1000BASE-T RJ-45 WAN Port

Grounding Point

DC Power Jack

5 6 7 8

1000BASE-T RJ-45 DMZ Port

USB Port

Console Port

Reset Button

– 12 –

System Board Layout

Figure 3: System Board

1 2 3 4

Chapter 1

| System Overview

System Board Layout

Fan power connectors

DDR SODIMM slot

CPU and heatsink

System battery

HDD/SSD power connector

SATA III ports

M.2 SSD card slot

13 12 11 10

2.5” 500 GB HDD

Reset button

10. Console port

11. USB slot

12. RJ-45 WAN and DMZ ports

13. RJ-45 LAN ports

14. DC power jack

– 13 –

Chapter 1

| System Overview

System Block Diagram

Figure 4: System Block Diagram

– 14 –

Chapter 1

| System Overview

System Specifications

Table 1: SAF51003I Specifications

Item

Form-Factor

Dimensions (W x D x H):

Weight

CPUs

Memory

Local Storage

I/O Interfaces

Network Interfaces

Expansion

Accelerator

OS Version

Power Adapter

System Cooling

Temperature

Humidity

Compliances

Specification

Compact desktop

300 x 200 x 38.5 mm (11.81 x 7.87 x 1.52 inches)

1.58 kg (3.48 lb)

SoC, Intel® Atom™ Processor for Communications C3000 Series

(FCBGA, 14nm), supports 2-4 cores, 2.2 GHz (turbo 2.4 GHz)

Sockets: 2 x 260pin DDR4 SODIMM slots

Type: DDR4 1866/2133/2400 MT/s (64GB max)

1 x M.2 SATAIII SSD, support 2242/2280 type

1 x 2.5” 500GB HDD

Optional on-board eMMC 16-256GB (not equipped by default)

1 x RJ-45 type serial console

1 x hardware reset button (through hole)

1 x RJ-45 GbE for DMZ

1 x RJ-45 GbE port for WAN

8 x RJ-45 GbE for LAN

Type: 1x Mini PCIe

Signal: PCIe x1 and USB 2.0

Advanced Technologies: Intel® VT-x, Intel® VT-d, SR-IOV, VMDq,

QuickAssist, PECI over SMBUS, eSPI, NC-SI, Core and Memory

RAPL, Memory OLTT and CLTT

Ubuntu 16.04 Server X64

Input: AC 110 to 240 @ 50/60 Hz

Output: 12 VDC, 5.0 A, 60 W

2x PWM fans, supporting smart-fan

Operating: 0 °C to 40°C (32 °F to 104 °F)

Storage: -20 °C to 70 °C (-4 °F to 158 °F)

Operating: 20% to 90% (non-condensing)

Storage: 5% to 90% (non-condensing)

FCC

RoHS 2.0

– 15 –

System Components

This chapter includes the following sections:

■ “Power Supply” on page 17

■ “System Memory” on page 17

■ “M.2 Solid-State Drives (SSDs)” on page 18

■ “Mini PCIe Slot” on page 18

■ “System Battery” on page 19

– 16 –

Chapter 2

| System Components

Power Supply

The server system includes an external AC/DC power adapter. The power adapter connects to an AC power source in the range 110 to 240 VAC, 50/60 Hz.

Figure 5: AC/DC Power Adapter

AC power cord socket 2.

DC power connector

System Memory

The server has one DIMM memory slot. The slot accepts a 260-pin DDR4

SODIMM. You can install up to a maximum of 32GB.

Figure 6: DIMM Slot

DIMM slot

– 17 –

Module release lever

Chapter 2

| System Components

M.2 Solid-State Drives (SSDs)

The server supports a single SSD (32GB default) in compact M.2 form factor for local storage. The 2242/2280 type SSD card installs into the M.2 SATA III slot on the system board.

Figure 7: M.2 SSD Slot on System Board

1 2

M.2 securing screw

M.2 slot

SSD 2280/22110 M.2 card

Mini PCIe Slot

The server supports one standard Mini PCIe slot for add-in cards. A second Mini

PCIe slot (CONN 6) is non-standard with added 5 VDC power on pin 17.

Figure 8: Mini PCIe Slot

1 2

Standard Mini PCIe card slot

– 18 –

Non-standard Mini PCIe card slot

Chapter 2

| System Components

System Battery

The server system includes one lithium battery. If the system no longer displays the correct date and time, the system battery may need to be replaced.

Be sure to replace the battery with the same type, a CR2032 lithium battery.

Warning: Risk of fire if the battery is installed incorrectly.

Figure 9: System Battery

System battery

– 19 –

Section II

Installation Procedures

This section provides details on installing server hardware.

This section includes these chapters:

■ “Chassis Installation” on page 21

■ “Server Connections” on page 25

– 20 –

Chassis Installation

This chapter includes the following sections:

■ “General Installation Guidelines” on page 22

■ “Installation Precautions” on page 22

■ “Installing the Server Appliance on a Desktop” on page 23

■ “Appliance Cooling Requirements” on page 23

■ “Removing the Top Cover” on page 24

– 21 –

Chapter 3

| Chassis Installation

General Installation Guidelines

Be sure to follow the guidelines below when choosing a location.

■ The installation location should:

■ be able to maintain its temperature within 0 to 45 °C (32 to 113 °F) and its humidity within 10% to 90%, non-condensing.

■ provide adequate space (approximately five centimeters or two inches) on all sides for proper air flow.

■ be accessible for installing, cabling and maintaining the device.

■ allow the status LEDs to be clearly visible.

■ Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting fixtures and other sources of electrical interference, such as radios and transmitters.

■ Make sure that the unit is connected to a separate grounded power outlet and is powered from an independent circuit breaker. As with any equipment, using a filter or surge suppressor is recommended. Verify that the external power requirements for the switch can be met as listed under “Power Supply Units” on page 27 .

Installation Precautions

Warning: This appliance uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

Warning: When selecting a fiber QSFP+ device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved

Laser Class 1 QSFP+ transceiver.

Caution: Before installing your appliance, first review all the safety statements and guidelines in the Safety and Regulatory Information document.

Caution: The earth connection must not be removed unless all supply connections have been disconnected.

– 22 –

Chapter 3

| Chassis Installation

Installing the Server Appliance on a Desktop

The server appliance can be installed on a desktop or shelf.

To install the appliance on a desktop, follow these steps:

Attach the four adhesive feet to the bottom of the device.

Figure 10: Installing the Appliance on a Desktop

Adhesive feet.

Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow.

Appliance Cooling Requirements

Wherever the appliance is located, be sure to pay close attention to the device’s cooling requirements. The location should be well ventilated and provide unrestricted air flow at the front, back, and sides of the appliance. If the air flow is insufficient, it may cause the appliance to overheat and possibly fail.

– 23 –

Chapter 3

| Chassis Installation

Removing the Top Cover

To access internal components of the appliance, the top cover must be removed.

Figure 11: Removing the Top Cover

Side panel screws (2)

Open direction

Bottom panel screws (2)

Unscrew the two side panel screws and two bottom panel screws.

Push the cover towards the rear until it is free.

Lift the cover off to remove it.

– 24 –

Server Connections

This chapter includes the following sections:

■ “Grounding the Device” on page 26

■ “Connecting Power and Powering On” on page 27

■ “Connecting to the Console Port” on page 27

■ “Connecting to 1000BASE-T Network Ports” on page 29

– 25 –

Chapter 4

| Server Connections

Grounding the Device

The rear panel of the server appliance includes a single-screw grounding terminal.

The surface area around this terminal is not painted in order to provide for a good connection. The terminal must be connected to ground to ensure proper operation and to meet electromagnetic interference (EMI) and safety requirements.

Figure 12: Grounding the Device

Grounding terminal 2.

#14 AWG grounding wire

Before powering on the server, ground the device to earth as described below.

Ensure the device is properly grounded in compliance with ETSI ETS 300 253.

Verify that there is a good electrical connection to the grounding point (no paint or isolating surface treatment).

Disconnect all power cables to the device.

Attach a #14 AWG stranded copper wire to the grounding terminal on the server.

Then attach the grounding wire to the ground point.

Caution:

The earth connection must not be removed unless all supply connections have been disconnected.

– 26 –

Chapter 4

| Server Connections

Connecting Power and Powering On

The server needs to be powered from the included AC/DC power adapter. Before connecting the AC/DC power adapter to an AC power source, first verify that the external AC power source can provide 110 to 240 VAC, 50/60 Hz.

To connect the server to a power source:

Connect the AC/DC power adapter to the DC power jack on the device.

Figure 13: Connecting Power to the Server

DC power jack 2.

AC/DC power adapter connector

Connect the AC/DC power adapter to an AC power source.

Check the PWR LED indicator on the server to verify that power is being received. If not, recheck the power cord connections at the AC supply source and the AC/DC power adapter.

Connecting to the Console Port

The RJ-45 Console port on the server’s rear panel is used to connect to the server for BIOS configuration. The console device can be a PC or workstation running a

VT-100 terminal emulator, or a VT-100 terminal. An RJ-45 to DB-9 console cable can be used for connecting to a PC’s RS-232 serial DB-9 DTE (COM) port.

Note: To connect to notebooks or other PCs that do not have a DB-9 COM port, you can use a USB-to-male DB-9 adapter cable (not included with the server).

– 27 –

Chapter 4

| Server Connections

Connecting to the Console Port

Figure 14: Connecting to the Console Port

Console port

The following table describes the pin assignments used in the console cable.

Table 2: Console Cable Wiring

Server’s RJ-45

Console Port

6 RXD (receive data)

Null Modem

3 TXD (transmit data)

<---------------------

--------------------->

4,5 SGND (signal ground) -----------------------

No other pins are used.

PC’s 9-Pin

DTE Port

3 TXD (transmit data)

2 RXD (receive data)

5 SGND (signal ground)

The serial port’s configuration requirements are as follows:

■ Default Baud rate—115200 bps

■ Character Size—8 Characters

■ Parity—None

■ Stop bit—One

■ Data bits—8

■ Flow control—none

Follow these steps to connect to the Console port:

Attach one end of the included RJ-45-to-DB-9 serial cable to a DB-9 COM port connector on a management PC.

– 28 –

Chapter 4

| Server Connections

Connecting to 1000BASE-T Network Ports

Attach the other end of the serial cable to the Console port on the server.

Configure the PC’s COM port required settings using VT-100 terminal emulator software (such as HyperTerminal) running on the management PC.

Press the Enter key on the management PC to access the BIOS.

If you boot the Ubuntu OS, log in using the default user account and password:

■ Account: edgecore

■ Password: 1111

■ Root Password: 1111

For a detailed description of BIOS configuration settings, see “BIOS Settings” on page 36 .

Connecting to 1000BASE-T Network Ports

The RJ-45 10/100/1000BASE-T network ports on the server support automatic

MDI/MDI-X pinout configuration, so you can use standard straight-through twistedpair cables to connect to any other network device. The connections require unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cables with RJ-45 connectors at both ends.

Table 3: Maximum Twisted-Pair Copper Cable Lengths

Cable Type

1000BASE-T

Category 5, 5e, or 6 100-ohm UTP or STP

100BASE-TX

Category 5 or better 100-ohm UTP or STP

10BASE-T

Category 3 or better 100-ohm UTP

Maximum Cable Length Connector

100 m (328 ft)

RJ-45

Follow these steps to connect network cable an RJ-45 port:

Attach one end of a twisted-pair cable to the network device’s RJ-45 port.

– 29 –

Chapter 4

| Server Connections

Connecting to 1000BASE-T Network Ports

Figure 15: Connecting to 1000BASE-T RJ-45 Ports

RJ-45 network port

Attach the other end to an RJ-45 port on the server.

As a connection is made, the status LEDs on the server port will turn on to indicate that the connection is valid.

Table 4: RJ-45 Port Status LEDs

LED Condition Status

Status (link/activity) On/Blinking Green The port has a valid 1 Gbps link. Blinking indicates traffic passing through the port.

On/Blinking Amber The port has a valid 10/100 Mbps link. Blinking indicates traffic passing through the port.

Off There is no valid link on the port.

– 30 –

Section III

System Configuration

This section provides a description of system software configuration.

This section includes these chapters:

■ “BIOS Setup Access” on page 32

■ “BIOS Settings” on page 36

– 31 –

BIOS Setup Access

This chapter includes the following sections:

■ “BIOS Introduction” on page 33

■ “Accessing the BIOS Setup Menu” on page 33

■ “BIOS Setup Utility Keyboard Commands” on page 34

– 32 –

Chapter 5

| BIOS Setup Access

BIOS Introduction

The American Megatrends Inc. (AMI) BIOS software handles all basic communications between the CPUs and peripherals, as well as including code that supports advanced server system features. You can configure the BIOS settings through its menu-driven interface and then save the configuration into memory.

Note: You can access the system BIOS and configure settings with or without an operating system installed on the server.

This chapter describes how to access the BIOS setup menus and the following chapter, “BIOS Settings” on page 36 , describes the configuration settings.

Note that the majority of configuration settings are preconfigured as BIOS default values, whereas others are automatically detected during the boot-up process and configured without requiring any actions.

Accessing the BIOS Setup Menu

The server’s BIOS settings can be accessed through the console port.

Connect a computer running VT-100 terminal emulator software to the console port following the procedure in the section “Connecting to the Console Port” on page 27 .

Figure 16: Access to BIOS Settings

Console port

Power-on the server.

– 33 –

Chapter 5

| BIOS Setup Access

BIOS Setup Utility Keyboard Commands

When the BIOS boot message is displayed, press <Esc> on the keyboard to enter the BIOS setup menu.

Figure 17: BIOS Setup Menu Access

The BIOS main menu displays and you can view settings and make configuration changes.

Figure 18: BIOS Main Menu

BIOS Setup Utility Keyboard Commands

The AMI BIOS setup utility uses only the connected computer keyboard for menu navigation and configuration settings. The commands for each menu are shown on the right side of each menu.

The basic commands are describe in Table 5 .

Table 5: BIOS Setup Utility Commands

Key

Right and Left arrows

Up and Down arrows

<Enter>

Action

Moves the cursor left or right (selects the menu).

Moves the cursor up or down (Selects the submenu or fields).

Selects the highlighted submenu.

– 34 –

Chapter 5

| BIOS Setup Access

BIOS Setup Utility Keyboard Commands

Table 5: BIOS Setup Utility Commands (Continued)

Key Action

+ (plus key)

- (minus key)

<F1>

<F2>

<F3>

<F4>

<Esc>

Scrolls forward through setting options of the highlighted field.

Scrolls backward through setting options of the highlighted field.

Displays help navigation.

Loads the previously used configuration.

Loads optimized default values.

Saves the configuration and exits the setup utility.

Exit the BIOS setup utility or the current submenu.

– 35 –

BIOS Settings

This chapter includes the following sections:

■ “Main Menu” on page 37

■ “Advanced Menu” on page 38

■ “IntelRCSetup” on page 39

■ “Security menu” on page 40

■ “BOOT Menu” on page 41

■ “Save and Exit Menu” on page 42

– 36 –

Main Menu

The main menu describes general system information.

Figure 19: BIOS Main Menu

Chapter 6

| BIOS Settings

Main Menu

This menu includes the following items:

■ BIOS Vendor — American Megatrends.

■ BIOS Version — The BIOS version.

■ Build Date and Time — Shows the BIOS build date and time.

■ Access Level — Displays the access rights of the current BIOS user.

■ Total Memory — Displays the total system memory.

■ System Language — Selects the display language for the BIOS.

■ System Date — Displays the RTC date. Use the [+] or [-] keys to set the date.

■ System Time — Displays the RTC time. Use the [+] or [-] keys to set the time.

– 37 –

Chapter 6

| BIOS Settings

Advanced Menu

The Advanced menu includes items for Trusted Computing and other system features.

Figure 20: BIOS Advanced Menu

This menu includes the following items:

■ Trusted Computing — Trusted Computing settings.

■ ACPI Settings — The Advanced Configuration and Power Interface (ACPI) settings. ACPI is the standard method for computers to discover and configure hardware components.

■ HW Monitor — Information on hardware health status.

■ Smart Fan Function — Configures system fan speeds and temperature threshold settings.

■ S5 RTC Wake Settings

— Enables the system to wake from an ACPI S5 (soft off) state based on a real-time clock alarm setting.

■ Serial Port Console Redirection — Settings that enable the BIOS settings to be configured from a serial port connection.

■ SIO Configuration

— Super I/O chip functions, such as serial port settings.

■ PCI Subsystem Settings

— Configures settings for PCI, PCI-X, and PCI.

– 38 –

Chapter 6

| BIOS Settings

IntelRCSetup

■ Network Stack Configuration — Enables the Unified Extensible Firmware

Interface (UEFI) network boot option.

■ CSM Configuration — Compatibility Support Module (CSM) configuration.

Settings for CSM provide support for legacy operating systems that are not UEFI compatible.

■ SDIO Configuration — Configures settings for access to SD storage devices.

■ USB Configuration — Configures settings for USB controllers and ports.

IntelRCSetup

The Intel RC Setup menu provides configuration access to Intel chipset features.

Figure 21: BIOS Intel RC Setup

This menu includes the following items:

■ Platform — The platform name of the Intel chipset.

■ RC Revision — The version of the Intel chipset.

■ Processor BSP Revision — The version of the Intel board support package.

■ Microcode Revision — The version of the Intel chip microcode.

■ Processor Configuration — Configures parameters related to the CPU.

■ CPU Thermal Configuration — Configures settings for CPU thermal control.

– 39 –

Chapter 6

| BIOS Settings

Security menu

■ CK420 Configuration — Enables spread spectrum support for the clock generator to reduce system EMI.

■ Miscellaneous Configuration — Settings for other Intel chipset parameters.

■ Wake on LAN Configuration — Enables network interface Wake on LAN function to power on the system.

■ North Bridge Chipset Configuration — Configures parameters for the processor memory, PCI bus connections, and AGP graphics functions.

■ South Bridge Chipset Configuration — Configures parameters for controlling system I/O functions.

Security menu

The Security menu allows you to set passwords to protect the system from unauthorized access.

Administrator

Password

The administrator password is limited to 3-20 characters and is case sensitive. The password does not support special characters, such as "!", "%", "^", "~".

When the administrator password is set, the password must be entered to access the BIOS setup menu. If an incorrect password is entered more than three times, the system BIOS displays a warning message.

User Password

The user password is limited to 3-20 characters and is case sensitive. The password does not support special characters, such as "!", "%", "^", "~".

When a user password is set, you must enter the password during system boot and to access the BIOS setup menu. If an incorrect password is entered more than three times, the system BIOS displays a warning message.

Note: To set a user password, you must first set an administrator password. Setting a user password first automatically sets the administrator password by default.

Note: If you forget the administrator password, the BIOS settings must be cleared by removing the system battery.

– 40 –

Figure 22: BIOS Security Menu

Chapter 6

| BIOS Settings

BOOT Menu

The Boot menu allows you to set the boot device priority sequence and various other parameters.

Figure 23: BIOS Boot Menu

– 41 –

Chapter 6

| BIOS Settings

Save and Exit Menu

This menu includes the following items:

■ Setup Prompt Timeout — The number of seconds to wait for the keystroke to enter the BIOS setup menu. (Range: 1-65535 seconds)

■ Bootup NumLock State — Sets the keyboard Numlock state.

■ Quiet Boot — Sets the screen display during boot-up. When set to disabled, the system displays POST messages. When set to enabled, the system logo is displayed.

■ Boot Option Priorities — Sets the priority sequence for boot device types. The selection for Boot Option #1 is the first priority.

■ Hard Drive BBS Priorities — Sets the boot priority sequence for installed hard drive devices.

Save and Exit Menu

The Save and Exit menu provides options for saving BIOS settings and exiting the setup utility.

Figure 24: BIOS Save and Exit Menu

This menu includes the following items:

■ Save Changes and Exit — Saves the current settings and exits the BIOS setup utility. Select the field and press Enter. In the dialog box that displays, select

“Yes” to save the settings and exit the BIOS setup utility.

– 42 –

Chapter 6

| BIOS Settings

Save and Exit Menu

■ Discard Changes and Exit — Discards the current changes, and exits the

BIOS setup utility.

■ Save Changes and Reset — Saves the current changes and reboots the server.

■ Discard Changes and Reset — Discards the current changes and reboots the server.

■ Save Changes — Saves the current BIOS settings.

■ Discard Changes — Discards the current changes.

■ Restore Defaults — Restores the BIOS configuration to factory default values.

■ Save as User Defaults — Saves the current BIOS configuration as a User

Default.

■ Restore User Defaults — Restores the BIOS configuration to previously saved

User Default values.

■ Boot Override — Allows you to select an available boot option that overrides other boot priorities when you exit the BIOS setup utility and reboot the system.

– 43 –

Section IV

Appendices

This section provides additional information and includes these items:

■ “Troubleshooting” on page 45

■ “Installing the Intel Driver” on page 47

■ “LED Control Utility” on page 48

■ “Safety and Regulatory Information” on page 49

– 44 –

Troubleshooting

When possible, before checking specific troubleshooting options, always look for

POST messages by first rebooting the server using one of these methods:

■ Reset the system through OS software.

■ Power down by removing power to the unit.

Power Supply

If the server does not power on, check these items:

■ Make sure power is available at the source outlet.

■ Look for loose power cord connections.

Note: If you cannot isolate the power problem, the power adapter may be defective. Replace the power adapter and check all items again.

POST and Boot Problems

If the server does not complete the POST or boot the OS, check these items:

■ Check the POST messages for errors.

■ Check installed SSD cards are properly seated.

■ Check the boot settings in the BIOS.

■ OS software is not installed or corrupted. Reinstall the OS.

Cooling and Fans

If the system is running hot, check these items:

■ Make sure the top cover is installed.

– 45 –

Appendix A

| Troubleshooting

Network Connections

■ Check to be sure the ambient temperature is not too high.

■ Make sure all fans are running properly.

■ Check the fan settings in the BIOS. The fans might need to run at a higher speed.

■ Make sure that airflow around the server is not obstructed.

Network Connections

If there are problems with network connections, check these items:

■ Verify that the server and attached device are powered on.

■ Be sure the cable is plugged into both the server port and corresponding device.

■ Verify that the proper cable type is used and its length does not exceed specified limits.

■ Check the attached device and cable connections for possible defects. Replace the defective cable if necessary.

– 46 –

Installing the Intel Driver

If after installing the Linux OS some RJ-45 ports cannot be found, download and install the latest Intel ixgbe driver for your OS.

For example, you install Ubuntu 16.04.4 and find that ports LAN1–LAN8 can be used by the built-in Intel igb driver, but the WAN and DMZ ports cannot be found in the OS. In this case, download and install the latest Intel ixgbe driver.

The Intel ixgbe driver and related information can be found at the following URL: https://downloadcenter.intel.com/download/14687/Intel-Network-Adapter-Driverfor-PCIe-Intel-10-Gigabit-Ethernet-Network-Connections-Under-Linux-

– 47 –

LED Control Utility

The custom-defined Status LEDs can be controlled using a software utility. If you do not have the Utility file, contact Edgecore sales or technical support.

Figure 25: Status LEDs

Status 1 and Status 2 LEDs

Make sure you have the Utility file, which includes two files; devmen2.c

and test_led.py

At the Linux command line, type gcc -o devmem2 devmem2.c

to compile.

Execute test_led.py

to see detailed information and how to use the utility.

Figure 26: LED Control Utility

– 48 –

Safety and Regulatory

Information

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or better for 10 Mbps connections, Category 5 or better for 100 Mbps connections,

Category 5, 5e, or 6 for 1000 Mbps connections. For fiber optic connections, you may use 50/125 or 62.5/125 micron multimode fiber or 9/125 micron singlemode fiber.

Japan - VCCI Class A

この装置は , クラス A 情報技術装置です。この装置を家庭環境で使用す

ると電波妨害を引き起こすことがあります。この場合には使用者が適切な

対策を講ずるよう要求されることがあります。 VCCI-A

CE Mark

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the

Council Directive 2014/30/EU on the Approximation of the laws of the Member

States relating to Electromagnetic Compatibility and 2014/35/EU for electrical equipment used within certain voltage limits. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission: ■ Limit according to 55032:2012+AC:2013, Class A

■ Limit for harmonic current emission according to EN 61000-

3-2:2014, Class A

■ Limitation of voltage fluctuation and flicker in low-voltage supply system according to EN 61000-3-3:2013

Immunity: ■ Product family standard according to EN 55024:2010+

A1:2015

– 49 –

Appendix D

| Safety and Regulatory Information

LVD:

■

Electrostatic Discharge according to IEC 61000-4-2:2008

ED. 2.0

Radio-frequency electromagnetic field according to

IEC 61000-4-3:2010 ED. 3.2

Electrical fast transient/burst according to IEC 61000-4-

4:2012 ED. 3.0

Surge immunity test according to IEC 61000-4-5:2014 ED.

3.0

Immunity to conducted disturbances, Induced by radiofrequency fields: IEC 61000-4-6:2013 ED. 4.0

Power frequency magnetic field immunity test according to

IEC 61000-4-8:2009 ED. 2.0

Voltage dips, short interruptions and voltage variations immunity test according to IEC 61000-4-11:2004 ED. 2.0

EN 60950-

1:2006+A11:2009+A1:2010+A12:2011+A2:2013

PSE Alarm

本製品に同梱いたしております電源コードセットは、

本製品専用です。本電源コードセットは、本製品以外の

製品並びに他の用途でご使用いただくことは出来ません。

製品本体に同梱された電源コードセットを利用し、他製品

の電源コードセットを使用しないで下さい。

Power Cord Safety

Please read the following safety information carefully before installing the switch:

Warning: Installation and removal of the unit must be carried out by qualified personnel only.

■ The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.

■ Do not connect the unit to an A.C. outlet (power supply) without an earth

(ground) connection.

■ The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN 60320/IEC 320 appliance inlet.

■ The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.

– 50 –

Appendix D

| Safety and Regulatory Information

■ This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth

(ground).

† Impédance à la terre

Important! Before making connections, make sure you have the correct cord set.

Check it (read the label on the cable) against the following:

Power Cord Set

U.S.A. and Canada

Denmark

Switzerland

U.K.

Europe

The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA 5-15P

(15 A, 125 V) configuration.

The supply plug must comply with Section 107-2-D1, Standard DK2-1a or

DK2-5a.

The supply plug must comply with SEV/ASE 1011.

The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with a 5 A fuse which complies with BS1362.

The mains cord must comply with IEC 60227 (designation

60227 IEC 52).

The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must comply with IEC 60227 (designation

60227 IEC 52).

IEC-320 receptacle.

Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:

Avertissement: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.

■ Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).

■ Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.

– 51 –

Appendix D

| Safety and Regulatory Information

■ Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit respecter une configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.

■ La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de cette prise.

■ L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à la terre (masse).

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la

CSA.

Les spécifications minimales pour un cable flexible sont AWG No. 18, ouAWG No. 16 pour un cable de longueur inférieure à 2 mètres.

- type SV ou SJ

- 3 conducteurs

Danemark:

Suisse:

Europe

Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre (mise

à la masse) et respecter la configuration NEMA 5-15P (15 A, 125 V).

La prise mâle d’alimentation doit respecter la section 107-2 D1 de la norme DK2 1a ou DK2 5a.

La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011.

La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”)

Le cordon d'alimentation doit être conforme à la norme IEC 60227 (IEC

60227 désignation 52)

Bitte unbedingt vor dem Einbauen des Switches die folgenden

Sicherheitsanweisungen durchlesen:

Warnung: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal erfolgen.

■ Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden.

– 52 –

Appendix D

| Safety and Regulatory Information

■ Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die internationalen Sicherheitsnormen erfüllt.

■ Der Gerätestecker (der Anschluß an das Gerät, nicht der

Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320 konfigurierten

Geräteeingang haben.

■ Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die

Stromversorgung des Geräts kann nur durch Herausziehen des

Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.

■ Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-

Bedingungen betrieben werden.

Stromkabel . Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.

Europe Das Netzkabel muss mit IEC 60227 (IEC 60227 entsprechen Bezeichnung 52)

Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

– 53 –

SAF51003I

E052018-CS-R01

Witaj! Jestem chatbotem AI specjalnie przeszkolonym, aby pomóc Ci w obsłudze Edge-Core SAF51003I User Manual. Dokładnie przejrzałem dokument i mogę pomóc Ci zlokalizować dokładne informacje, których potrzebujesz, lub wyjaśnić treść w jasny i prosty sposób. Niezależnie od tego, czy szukasz wskazówek dotyczących konkretnych funkcji, kroków rozwiązywania problemów, czy ogólnego użytkowania, możesz zadawać pytania. Im więcej szczegółów podasz na temat swoich obaw lub potrzeb, tym dokładniej i skuteczniej mogę Ci pomóc!

Asystent pisze

Asystent jest niedostępny. Spróbuj ponownie później.

Reklama