advertisement
i
Intellectual Property Rights (IPR) Information
Copyrights
Trademarks
© All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.
The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8 and
Explorer are trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Warranty
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the router yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.
Do not stack the routers.
The router should be used in a sheltered area, within a temperature range of 0 to +40 Celsius.
Do not expose the router to direct sunlight or other heat sources.
The housing and electronic components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
Keep the package out of reach of children.
When you want to dispose of the router, please follow local regulations on conservation of the environment.
We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. ii
Vigor2912 Series
Dual-WAN Security Router
Quick Start Guide
T a b l l e o f f C o n t t e n t t s
1 .
.
P a c k a g e C o n t t e n t t .................................................................................................. 1
2 .
.
P a n e l E x p l a n a t i o n
3 .
.
H a r d w a r e I I n s t t a l l l l a t t i i o n
3 .
.
1 N e t t w o r r k C o n n e c t t i i o n ................................................................................................................... 6
3 .
.
2 W a l l l l M o u n t t e d I I n s t t a l l l l a t t i i o n ........................................................................................................... 7
4 .
.
S o f f t t w a r e C o n f f i i g u r r a t t i i o n
5 .
.
C u s t t o m e r S e r v i i c e ............................................................................................... 12 iii
1 .
.
P a c k a g e C o n t t e n t t
Take a look at the package content. If there is anything missed or damaged, please contact
DrayTek or dealer immediately.
Vigor router
RJ-45 Ethernet Cable
Quick Start Guide
2x antenna (“n” model)
Power Adapter
1
2 .
.
P a n e l l E x p l l a n a t t i i o n
V i i g o r r 2 9 1 2
LED
ACT (Activity)
WCF
QoS
DoS
LAN (P4~P1)
WAN(W2~W1)
VPN
USB
Status
Blinking
Off
On
Off
On
Off
On
Blinking
On
Off
Blinking
On
Off
Blinking
On
On
Blinking
Explanation
The router is powered on and running normally.
The router is powered off.
The Web Content Filter is active. (It is enabled from Firewall >> General Setup ).
The Web Content Filter is inactive.
The QoS function is active.
The QoS function is inactive.
The DoS/DDoS function is active.
It will blink while detecting an attack.
The port is connected.
The port is disconnected.
The data is transmitting.
Internet connection is ready.
Internet connection is not ready.
The data is transmitting.
The VPN tunnel is active.
USB device is connected and ready for use.
The data is transmitting.
2
Interface
PWR
ON/OFF
USB
W1~W2/P1
W2/P1~P4
Factory Reset
Description
Connecter for a power adapter.
Power Switch.
Connecter for a USB device (for 3G/4G USB Modem or printer).
Connecter an ADSL or cable modem for accessing
Internet (WAN).
Connecters for local network devices (LAN).
Restore the default settings. Usage: Turn on the router
(ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.
3
V i i g o r r 2 9 1 2 n
LED
ACT (Activity)
WCF
QoS
WLAN
LAN (P4~P1)
WAN(W2~W1)
VPN
USB
Status
Blinking
Off
On
Off
On
Off
On
Blinking
On
Off
Blinking
On
Off
Blinking
On
On
Blinking
Explanation
The router is powered on and running normally.
The router is powered off.
The Web Content Filter is active. (It is enabled from Firewall >> General Setup ).
The Web Content Filter is inactive.
The QoS function is active.
The QoS function is inactive.
Wireless access point is ready.
It will blink slowly while wireless traffic goes through.
ACT and WLAN LEDs blink quickly and simultaneously when WPS is working, and will return to normal condition after two minutes.
(You need to setup WPS within 2 minutes.)
The port is connected.
The port is disconnected.
The data is transmitting.
Internet connection is ready.
Internet connection is not ready.
The data is transmitting.
The VPN tunnel is active.
USB device is connected and ready for use.
The data is transmitting.
4
Interface
PWR
ON/OFF
USB
W1~W2/P1
W2/P1~P4
Wireless LAN
ON/OFF/WPS
Factory Reset
Description
Connecter for a power adapter.
Power Switch.
Connecter for a USB device (for 3G/4G USB Modem or printer).
Connecter for local network devices or modem for accessing Internet (WAN).
Connecters for local network devices (LAN).
Press "Wireless LAN ON/OFF/WPS" button once to wait for client device making network connection through
WPS.
Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on) or disable (WLAN LED off) wireless connection.
Restore the default settings. Usage: Turn on the router
(ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.
5
3 .
.
H a r r d w a r r e I I n s t t a l l l l a t t i i o n
This section will guide you to install the router through hardware connection.
3 .
.
1 N e t t w o r r k C o n n e c t t i i o n
1.
Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router with
Ethernet cable (RJ-45).
2.
Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and the other end of the cable (RJ-45) into the Ethernet port on your computer.
3.
Connect one end of the power cord to the router’s power port on the rear panel, and the other side into a wall outlet.
4.
Power on the device by pressing down the power switch on the rear panel.
5.
The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking.
6
3 .
.
2 W a l l l l M o u n t t e d I I n s t a l l l l a t t i i o n
Vigor router has keyhole type mounting slots on the underside.
1.
A template is provided on the Vigor router packaging box to enable you to space the screws correctly on the wall.
2.
Place the template on the wall and drill the holes according to the recommended instruction.
3.
Fit screws into the wall using the appropriate type of wall plug.
Note The recommended drill diameter shall be 6.5mm (1/4”).
4.
When you finished about procedure, the router has been mounted on the wall firmly.
7
4 .
.
S o f f t t w a r r e C o n f f i i g u r r a t t i i o n
To access Internet, please finish basic configuration after completing the hardware installation.
The Quick Start Wizard is designed for you to easily set up your router for Internet access.
You can directly access the Quick Start Wizard via Web Configurator.
1.
Make sure your PC connects to the router correctly.
Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router
192.168.1.1
.
2.
Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to ask for username and password. Please type “admin/admin” as the
Username/Password and click Login .
8
3.
Now, the Main Screen will pop up.
4.
Click Wizards>>Quick Start Wizard .
5.
Enter the login password on the field of New Password and retype it on the field of
Confirm Password . Then click Next to continue.
9
6.
On the next page as shown below, please select the WAN interface that you use. Then click Next for next step.
7.
On the next page as shown below, please select the appropriate protocol according to the information from your ISP . For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step.
10
PPPoE: If you click PPPoE as the protocol, after clicking Next , you will get the following web page. Please manually enter the Username/Password provided by your
ISP. Then click Next .
Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step.
11
DHCP: if you click DHCP, you will get the following page. Simply click Next to continue.
8.
Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet.
5 .
.
C u s t t o m e r r S e r r v i i c e
If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to [email protected].
12
advertisement
Related manuals
advertisement