alot =o

ee Installation Instructions

Electric Cooktop

For use with models ETT304-1, ETT365-2, MET304 and METB365-1

Part No. 65170 Rev. K

TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI 221.1 AND

UL 858 STANDARD FOR HOUSEHOLD COOKING APPLIANCES.

Table of Contents

Before YOu Bein... .........s:sccssssscscsececeseeeseesanananssasanenesesesnes 1

Important Safety INStruUCtiONS ...........ccceccececsnctcrsnsssreneeeeee 1

Planning the Location oo... cccccccccseececececececeeeeeeeeeeeeeeees 4

Cabinet Layout... ccccccsssesescseeeeeeeeeeeeeeeeeeeenenenenenes 4 important Information About Safety Instructions.............. 1 Installation INStruCtiOns................:sscccceccesecessnsnsssssssseeesveres 6

Safety Symbols and Labels 0.0... cccccccccccccccceceeeeeeeeeeneees 4 Chassis Installation 00... cc cccccccecececceccccceceeeeeeeeeeeeneneees 6

General Safety Precautions .............ccccccccccccccceceeeeeeeeeeneees 2

Installation Specifications. .............sccececsescsssesssssssseseseeree 3

Product DIMENSIONS ...... ccc cc ccccceceeeeecececececcceeeeeeeeeeneneees 3

Electrical Specifications ....... cc cccceteeeceeeeeeeseeeeeseeeeees 3

Verify the Package Contents...........ccccccccceseseeeeeeeeeeeeeees 6

Electrical COMMECTION 0... ccc ccc cccee esas ee eeesenesee ene eeeeeeees 6

Verifying Proper Operation .......ccccccccccccccceeeeseeeeeeeseeeeees 8

Customer Service Information

If You Need Help... Product Data Label

if you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team.

For repairs to Dacor appliances under warranty call the

Dacor Distinctive Service line. When you call, have the model and serial number of the appliance ready. The model and serial number are printed on the product data label.

*

* The product data label contains the model and serial number information and the electrical requirements. itis located on the bottom of the cooktop chassis.

Dacor Customer Service Team

Phone: (800) 793-0093 (U.S.A. and Canada)

Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time

Web site: www.dacor.com

Dacor Distinctive Service (for repairs under warranty)

Phone: (877) 337-3226 (U.S.A. and Canada)

Monday — Friday 6:00 a.m. to 4:00 p.m. Pacific Time

© 2007 Dacor, all rights reserved.

Before You Begin...

Important:

* Installer: In the interest of safety and to minimize problems, read these installation instructions completely and care- fully before you begin the installation process. Leave these installation instructions with the customer.

* Customer: Keep these installation instructions for future reference and the local electrical inspector’s use.

Important Safety Instructions

Important Information About DANGER

Safety Instructions IMPORTANT: Do not store or use combustible, flamma-

* The Important Safety Instructions and warnings in

ble or-explosive vapors and liquids (such as gasoline) on

or in the vicinity of this or any other appliance. Also keep this manual are not meant to cover all possible prob-

lems and conditions that can occur. Use common

items that could explode, such as-aerosol cans, away

from the cooktop. Do not.store flammable or explosive

sense and caution when installing, maintaining or oper- _| materials in adjacent cabinets or areas (including above

ating this or any other appliance. and below the cooktop).

* Always contact the Dacor Customer Service Team about problems and conditions that you don’t under- stand. See Customer Service Information.

WARNING

WARNING — NEVER use this appliance as a space

DANGER WARNING

Safety Sym bols a nd La bels injury.or death. heater.to heat or warm the room. Doing so may result in overheating of the appliance.

Immediate hazards that WILL result in severe personal WARNING — NEVER cover any-venis, slots, holes or passages:.on the cooktop chassis. Doing so blocks air flow through the cooktop and may cause.a fire hazard. for-example, near a-pool.

WARNING

Hazards or unsafe practices that COULD result in severe personal injury or death.

CAUTION

Hazards or.unsafe practices that. COULD-result in minor personal injury or property.damage.

WARNING

; - -

Do.not install this appliance.outdoors and/or-near water,

READ AND SAVE THESE INSTRUCTIONS

dacor 1

dacor.

Important Safety Instructions

General Safety Precautions

To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau- tions, including the following:

WARNING WARNING

Read :the accompanying use and care manual before To. avoid a fire hazard, do not hang flammable or-heat operating this appliance. sensitive objects over the cooktop.

Keep packaging materials away from children.-Plastic sheets and bags can cause suffocation.

Ifyou receive a damaged product, immediately con- tact your dealer or-builder. Do not install or use a damaged appliance. Do.not instail or use the appli- ance if the conduit:is damaged.

Do.not place. anything other-than cooking utensils on top of the cooktop. Do not use the cooktop.asa table or shelf. lf the cooktop is near-a window, do not use-long cur- tains as window treatment. The curtains could blow over the cooktop. and create a fire hazard.

This appliance must be properly installed.and ground- ed by a qualified installer according to these installa- tion: instructions prior. to use. The installer. must show the customer the location of the circuit breaker panel or fuse box so that they know where and how-to turn off power tothe cooktop. Dacor. is not responsible for the cost of correcting problems caused by improper installation. The owner is responsible to: make sure this appliance is properly installed.

Do. not install, repair or replace any-part of the cooktop-unless- specifically recommended in the litera- ture accompanying it. A qualified service technician must perform ail-other service.

DO NOT TOUCH THE SURFACES OF THE

COOKTOP DURING OR IMMEDIATELY AFTER USE.

After-use, make sure these surfaces have-had ‘suffi- cient time to cool before.touching them.

Do.not wear.loose or-hanging apparel while using the cooktop.Do. not allow.clothing to-come into.contact with hot surfaces andthe surrounding areas during and immediately after-use.

Do-not heat unopened food containers such as baby food jars and cans or-eggs. Pressure build-up may cause the container.to burst and cause injury.

Do not allow-pans to. boil-dry.

Before performing any. type of service or installation, make.sure that power to-the appliance is turned off.at the circuit breaker panel or-fuse-box.

Only-use the cooktop for-cooking tasks expected of-a home. appliance as-outlined.in the literature accompa- nying it.-This cooktop is not intended for commercial orindustrial use.

Do-not use corrosive chemicals or-vapors on or.in the vicinity of this appliance. Clean this appliance only in the manner specified-in the use and care manual.

Do not climb on any-part of the appliance.

Do-not leave. children or pets alone or unattended:in the area around.the cooktop. Do not allow children to play.with the controls.

Do not store items. of interest to children above or on top of the cooktop. Children could be burned ‘or injured while climbing on the appliance.

Do not store plastic or other utensils-with low melt- ing temperatures in drawers:immediately below. the cooktop.

Clean the cooktop before using it-for.the first time according to the use and care manuai.

Non-stick coatings, when: heated, can be harmful to birds.-Remove birds to a separate, well-ventilated room during cooking.

Do-not tamper with the controls. Do not adjust or alter any: part of the cooktop unless specifically instructed to do-so in this manual.

Keep flammable items, such as paper, cardboard, plastic and:cloth away from hot surfaces. Do not put such items:on the cooktop. Do not allow pot:holders to:touch hot surfaces.

Installation Specifications

Product Dimensions

All tolerances: +1/16 (£1.6 mm), unless otherwise stated.

4” (10.2 cm) oun US chassis height

3/16” (4.8 mm)

4” (10.2 cm) chassis height

3/16" (4.8 mm)

Models ETT304-1, MET304

(87.3 cm)

Models ETT365-2, METB365-1

* For units with stainless steel trim, other units may be up to 1/8” less

Electrical Specifications

* The junction box and the remote circuit breaker panel or fuse box, must be accessible when the cooktop is in place.

IMPORTANT

This appliance is provided with electrical connection leads ‘in a flexible metal conduit. These leads may be a

Model Dedicated Total Connected

Circuit Required Load**

ETT304-1

240 Vac, 60 Hz.

3 wire* 40 Amp.

6.9 kw

(29 Amp.)

smaller gage.than the standard househcoid wiring of the dedicated supply circuit, but they are suitable for.-connec- tion to these-circuits under the jurisdiction of the National

Electric. Code, and/or the local inspection authority.

* it is the owner’s responsibility to ensure that a licensed electrician performs the installation of the electrical sup- ply for this appliance. The electrical installation, includ- ing minimum supply wire size, must comply with the

National Electric Code ANSI/NFPA 70 (latest revision) and local codes and ordinances. A copy of the standard may be obtained from:

240 Vac, 60 Hz. 9.1 kW

ETT 365-2

METS04

3 wire* 40 Amp.

240 Vac, 60 Hz.

3 wire* 40 Amp.

(38 Amp.)

6.9 kw

(29 Amp.)

METB365-1

240 Vac, 60 Hz.

3 wire* 50 Amp.

9.6 kw

(40 Amp.)

* Two 120 Vac hot (L1 and L2) and one ground (all copper).

National Fire Protection Association

1 Batterymarch Park

Quincy, Massachusetts 02269-9101

** For reference only. See the product data label (on the bottom of the unit) for exact specifications. The minimum wire size required by the manufacturer is 8 AWG. Local codes may require that minimum wire gauge used exceed this requirement for the power requirements listed on the product data label.

* The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded, circuit that is protected by a properly sized circuit breaker or time-delay fuse. If a time-delay fuse is uti- lized, fuse both sides of the line (L1 and L2). dacor 3

Installation Specifications

Ventilation

WARNING

° IMPORTANT: Observe all governing codes and.-ordi- nances during planning and installation..Contact your local building department for further.information.

To reduce the risk of personal injury and to reduce accu- mulated smoke in the room, Dacor strongly recommends installing a vent hood or raised vent. Install the vent hood or raised vent according to the accompanying installation

*-.To-reduce the risk-of a fire hazard, all minimum/maxi- instructions. A vent hood should cover the entire cooking mum.clearances shown must be met or exceeded.

«When installing model ETT365-2 or METB365-1 and the bottom of the chassis:is to be enclosed wall to surface below it. if installing the cooktop with a raised vent, install only the following approved Dacor model numbers: wall, you must install ventilation duct kit ATD323. See

Cooktop Modeis Approved Raised Vent Models the duct installation instructions. for.cutout require- ments.

Planning the Location

Raised vent installation must allow room for the stiffener

ETT304-1 MET304 ERV30, PRV30 or RV30

ETT365-2 METB365-1 ERV36, PRV36 or RV36 bar on the back of the raised vent chassis. See below. *« Dacor recommends installing a non-combustible mate- rial on the rear wail behind the cooktop.

| 3/8" min. (1.0 cm)

* Carefully check the location where the cooktop is to be installed. It should be placed for convenient access. i

1 if

| iy

; : required behind cutout

Countertop

* To reduce the risk of personal injury caused by reach- ing over a hot appliance, cabinet storage space located directly above the cooktop should be avoided.

Stiffener.

~ a

ETT or MET series cooktop

4 i i i

* Make certain that electrical power meeting the specifi- cations on page 3 can be provided in the selected location. Verify that the electrical location is permitted by local building codes. Locate the junction box within reach of the included 48 inch long (122 cm) cooktop power conduit attached at the bottom right rear of the chassis. Do not lengthen the wiring. Make sure the underside of the cooktop and the junction box are accessible for inspection and service.

Cabinet Layout

Cabinet face -—+

'

| | - 3/8” min. (1.0 cm) space

| 4-]| behind raised vent chassis to clear stiffener vent: Check raised vent

| dimensions/specifications to determine proper fit

: rR

— min. clearance

A

| to combustible surfaces

A - Minimum Under Counter

Clearance (Width)

Under Counter Clearance

* Allow a minimum of six (6) inches (15.2 cm) clearance between the base of the glass cooktop frame and any combustible surface below, including the upper edge of drawers below the cooktop. Proper under-cabinet clearance is also required for the cooktop hold down brackets.

Cooktop Models

| 5/8” min. (1.6 cm)

| flat countertop overhang required behind cutout

Countertop

\

Stiffener._

ETT or MET series cooktop

Cabinet face --#1

-~ 5/8” min. (1.6 cm) space behind raised vent chassis to clear stiffener

-RV series raised vent:

Check raised vent dimensions/specifications to determine proper fit

9 7/8” (25.1 cm) with

CABP3 blower installed

ETT304-1, MET304

ETT365-2, METB365-1

30 1/2” (77.5 cm)

36 1/2” (92.7 cm)

4 dacor.

Side View: Cooktop and RV Series Raised Vent Under Counter Clearance - All Installations

Installation Specifications

Cabinet Cutout Dimensions Before making the countertop cutout, make certain that the required dimensions shown below have been met or

All tolerances: +1/16 (+1.6 mm), -0, unless otherwise stated. — ayceeded.

A - Overhead Clearances: All Installations

Cabinets that are:

1 Cooking surface is 3/16” (4.8 mm) thick.

A

Directly above cooking surface’ 30” (76.2 cm)

To left or right of cooking surface’? | 18” (45.7 cm)

? Not applicable for cabinets more than 6” (15.2 cm) to combustibles below cooktop chassis left or right of cooking surface.

B - Cutout Width:

Installations without Raised Vent ISO view without 2 1/4” min.

(5.7 cm)

B - Cooktop

(15.2 cm)

Models Cutout Width

ETT304-1,MET304. | 28 3/4” (73.0 cm)

ETT365-2, METB365-1 34 3/4” (88.3 cm)

4” min” AL eee)

Ng (15.2 cm) ae A ath ee

—| L

D

19 3/4"

(50.2 em)

Cabinet face

[=n =p ana naan nn nnn nn ann nnn nee =-4

.

4" min.

(2.5 cm)

6" min. | B > |. 6" min.

Countertop Cutout Without Raised Vent Installed

6" (15.2 cm) min. from mounting surface to combustibles below cooktop chassis

ISO view with raised vent

(15.2 cm)

Top view with raised vent

Countertop Cutout With Raised Vent Installed

Dimension Table - Installations with Raised Vent

Model/Configuration

C - Raised E - Raised F - Min. Rear

Cone Wioen Vent Cutout cutout Oa th

Width

Vent Countertop

PY | Cutout Depth | Overhang

ETT304-1 or MET304 cooktop with ERV30 or PRV30 raised vent.

22 1/2”

(57.2 cm)

2 3/4”

(7.0 cm)

3/8”

(1.0 cm) 28 3/4” 97 3/4”

ETT304-1 or MET304 cooktop with

RV30 raised vent. with ERV36 or PRV36 raised vent.

ETT365-2 or METB365-1 cooktop

with RV36 raised vent.

(73.0 cm)

34 3/4”

(88.3 cm)

(70.5 cm)

ETT365-2 or METB365-1 cooktop 22 1/2” 2 3/4” 3/8”

33 3/4”

(85.7 cm)

22 1/4” 2 1/2” 5/8”

(56.5 cm)

(57.2 cm)

(6.4 cm)

(7.0 cm)

(1.6 cm)

(1.0 cm)

22 1/4” 2 1/2” 5/8”

(56.5 cm) (6.4 cm) (1.6 cm) dacor.

Installation Instructions

Verify the Package Contents

Verify that all the items below have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appli- ance. Make sure that you have everything necessary to ensure proper installation before proceeding.

* Foam tape (PN 13208)

* Mounting bracket (PN 27251) w/bolt (PN, 83065)

QTY 2

* Glass scraper (PN 82499)

* Dacor Cooktop Cleaning Creme (PN A300)

* Product literature

Chassis Installation

WARNING

Ifthe electrical service provided does not meet the speci- fications on page 3, do not proceed with the instal- lation.-Call_a-licensed. electrician to ‘install the required wiring.

IMPORTANT

« Do not over-tighten the hold down bolis. Over tighten- ing the hold down bolts may result in damage.

* Do not use a hardening compound, glue or caulk to seal.the cooktop into place. The cooktop must. be readily. removable-if service is required. Removal of any sealant to service the unit will be performed at the customer’s-expense.

1. If the cooktop will be used with a raised vent, install the vent according to it’s installation instructions first. Install it in the back of the cutout.

Foam tape

2. Attach the foam tape provided with the unit to the underside of the cooktop mounting surface.

3. Lower the cooktop into the cutout and center it.

4. Secure the cooktop to the countertop utilizing the two

(2) hold-down brackets provided. Slide the brackets into the slots located on the left and right sides of the chassis, then tighten the screws to the underside of the countertop.

/

Cooktop Foam tape seal , \

1

L

Countertop

(LLLLL TS

Hold down bracket and screw —*

Electrical Connection

WARNING

«. To prevent an electric shock-or fire hazard, turn off power-to the circuit at the circuit breaker or fuse box prior to ‘connecting the cooktop wiring to the junction box.

*- Failure to:connect the cooktop:electrical wiring as specified: may-result-in an electric shock hazard, a fire hazard-and damage to.the appliance.

« -Connect the ground -(green) wire from the appliance to a grounded, metallic, permanent wiring system or grounding conductor. DO NOT ground the appliance with a neutral (white) house supply wire. A separate ground wire must be utilized:

* This appliance must be properly grounded according to these instructions. any-time power is applied.

° lf. aluminum house supply wiring is utilized, splice the appliance copper. wires to the aluminum house wiring using special connectors designed and agency-certi- fied for joining copper-and.aluminum. Follow the con- nector-manufacturer’s recommended procedure. care- fully. improper. connection may. result in a fire hazard.

IMPORTANT

Provide slack in the conduit to allow the cooktop to:slide out for-servicing.

1. Before proceeding, turn off power to the circuit to which the cooktop will be connected at the circuit breaker panel or fuse box.

2. Feed the appliance conduit into the electrical junction box and attach it using a UL certified strain relief.

3. Depending upon local codes, utilize one of the two methods shown on the facing page to connect the appliance to the power.

6 dacor

Installation Instructions

Three Wire Electrical Connection

See diagram on right.

1. Separate the wires coming out of the appliance conduit.

2. Connect the black wire from the appliance conduit to the black (L1) supply wire in the junction box.

3. Connect the red wire from the appliance conduit to the red (L2) supply wire in the junction box.

4. Connect the green wire from the appliance conduit to the green (ground) wire in the junction box.

| | incoming power

Junction box

Wire nut,

3 places

/

RED

RED BLACK

GREEN

GREEN

BLACK

#|

Conduit to cooktop =

Three Wire Connection

Three Wire Electrical Connection with

External Ground

WARNING

« . Do not ground the appliance to a.gas supply-pipe or hot water pipe.

*---lf connecting the ground-wire to a.grounded cold: water pipe, connect it using a separate. copper grounding wire. (No-10: minimum). and a‘clamp with an external grounding screw. The grounded-cold water pipe must have. metal continuity to electrical ground and must not be interrupted by insulating materials. Any insulating materials must be jumped with a-minimum 4. AWG wire to establish continuity to:ground. See diagram below right.

NOTE lf the junction box has-been properly grounded by-a licensed electrician, the green (ground) wire from the appliance conduit may be connected to the junction box using a-loop. terminal.

See diagrams on right.

1. Separate the wires coming out of the appliance conduit.

2. Connect the black wire from the appliance conduit to the black (L1) supply wire in the junction box.

3. Connect the red wire from the appliance conduit to the red (L2) supply wire in the junction box.

4. Connect the green wire from the appliance conduit to a grounded cold waiter pipe as shown. Jumper any insu- lating materials as shown with a length of No. 4 copper wire. Securely clamp the wire to bare metal at both ends.

Separate 10 AWG wire minimum \

Clamp wire tightly to cold water pipe

Incoming power | I

Junction box

Wire nut,

3 places

Cc

RED

RED BLACK »

BLACK d

GREEN

Cc GREEN

/

Ee Conduit to cooktop

Three Wire Connection with External Ground

4 AWG wire insulating device

(minimum)

Bare metal

Insulated Pipe Jumper dacor. 7

Installation Instructions

Verifying Proper Operation

WARNING

Read the accompanying use and care manual-completely before using the cooktop.

1. Clean the cooking surface according to the use and care manual prior to use.

2. Turn on the power to the cooktop at the circuit breaker or fuse box. When the unit is powered on for the first time, the cooktop controls will go through a self-check routine. For safety, when the self-check is complete, the cooktop controls will go into locked mode. Uniock the element controls:

® On ETT series models, push and hold the Dacor logo key for three seconds. Three beeps should sound and the Dacor logo indicator light should go out.

® On MET series models, push and hold the

CANCEL ¢ SECURE key for three seconds. Three beeps should sound and the CANCEL « SECURE indicator light should go out.

3. Turn on the left rear element by pressing the left rear

ON/OFF key. Press the 8 setting key (on the same row) to select heat level 8. Verify that the element begins to heat, then turn it off by pressing the ON/OFF key.

4. Repeat step 3 for the remaining burners. The left front burner has two different elements, an inner one and an outer one. To activate the outer element:

: con dacor

Cooktop Controls - Model ETT304-1

P

® Press the ON/OFF key for the left front element and press the 8 number setting.

® Activate the outer element by pressing the outer element key (the circle) on the right side of the ele- ment control.

® On model METB365-1, turn on both the right front and left front elements on setting 8, then press the bridge element key to verify it is working.

© jot

40

6 1 8°

5. For safety, lock the controls after testing is complete. a °

NOTE: if the cooktop does not operate properly, follow g°8 ° these troubleshooting steps: one 5° V

8

® Verify that power is supplied to the cooktop.

® Check for proper electrical connections.

® Make sure the cooktop controls are not locked (see step 2).

Repeat the above tests. if the appliance still does not work, contact Dacor

Distinctive Service at (877) 337-3226. Do not attempt to repair the appliance yourself. If you need service, be sure to have the model and serial num- oni g°e on clacor

Cooktop Controls - Model ETT365-2 bers available when you call. They are located on the bottom of the appliance.

8 dacor

Outer element key

Installation

Instructions

OS LAEEEEETrrep I!

ON/OFF of “CESESELELON Vf bey

ON/OFF

OQ — OX

ON/OFF

OT 80 yy O

SE LOODEaeereep!

ON/OFF

ee2ecar

Cooktop Controls - Model MET304

8°8 5

6° 5

ON/OFF

6-8 5

ON/OFF

6-8

ON/OFF

Sw 4

ON/OFF

ws ws is a

O

Outer element

key

O

is oS eEcar Bridge

element key

Cooktop Controls - Model METB365-1 dacor. 9

; ;

The Life of the Kitchen®

°

(ge TO a Opp

RTL yp ggg

Family Owned

American Made

Dacor e 600 Anton Bivd. Suite 1000 Costa Mesa, CA 92626 @ Phone: (800) 793-0093 e Fax: (626) 403-3130 « www.dacor.com