mangrove Smart Bracelet Instruction manual

 Device requirements: iOS 9.0 and above; Android 4.4 and above,
Bluetooth 4.0 is supported.
(Open the mobile client to set up personal information)
Switch to the "Device" page and click on the binding device)
+
(Click on your device in the list of scanned devices )
(Binding completed )
Main function interface
Main interface/dial
Inthe APP menu, click
"Theme Selection”
Switch the main interface SAT
/ dial.Dials come in 4 styles 23:23
00-6 MON
Pedometer/Distance/Calories
View steps, distance, calories burn in real time It can
synchronize apps in time to view motion data.
Body temperature interface
Switch to the temperature test interface to enter the
real-time temperature measurement and test data \
It can be updated to the APP type synchronously and
has atest report.
Note: When measuring body temperature, the bottom
electrode must be fully in contact with the skin (test after
10 minutes of wearing) The body temperature test will be
affected by the environmental temperature difference, and
it only serves as a warning reminder.Please refer to medical
professional equipment and doctor's diagnosis for details
OLD
Sleep monitoring function
When falling asleep, the bracelet will
automatically determine to enter the sleep
detection mode, and automatically detect
Calculate your sleep quality when you sleep
deep / light sleep / waking all night; sleep
Data can be updated to the APP simultaneously.
Note: Sleep data is only available when you wear the
bracelet to sleep.
Weather information
The weather page displays current weather, air
quality information, and tomorrow Condition.
Weather information needs to be connected to
the client before data can be obtained If you
disconnect for a long time, the weather information
will not be updated.
Note: Phone settings need to be turned on for positioning
Message interface
In the message interface, you can view the
message in three seconds in Changan.
After viewing the message, press and hold for
three seconds to exit.
More features page
On the More Functions page, press and
hold for three seconds to enter the lower
menu page for more operations.
Turn your wrist on
In the APP menu, click "Turn your wrist on
to brighten the screen"
On or off.
OID
‚Hand ring quick use instructions
Component introduction
Back electrode L
Display area
pay Heart rate sensor
Back electrodeR
Temperature
Charging icon
USB charging
interface
Touch button Front electrode
Note: When testing the ECG, you need to fully
contact the three electrodes with the skin
Instruction for Charging
For initial use, please take out the bracelet and charge it with the
corresponding charger. When charging, the bracelet will turn on
automatically (the charging method is shown in the following
figure: take the bracelet body out of the wrist strap and plug the
charging port into the standard USB port. The charging voltage is
5V.) The battery grid displays in scrolls when charging and the grid
will be full when it is fully charged.
PA >
Unplug the strap first Plug into th
(Touch the end of the button) port(Note the direction)
Install bracelet APP
Scan the QR code or enter the major
application markets
Download and install "SmartHealth”
USB
VELD
Heart rate monitoring
Switch to the heart rate monitor interface, Heart rate
monitoring, in real-time The measurement data can be
synchronized with the APP in real time with a test report.
Blood pressure monitoring
Switch to the blood pressure monitor interface, to enter
real-time monitoring. The measurement data can be
synchronized with the APP in real time with a test report.
Note: When measuring blood pressure, please measure
by the correct posture.The test result is for reference only, Cannot
be used as medical data.
ECG interface =
Press and hold the touch key on the ECG
interface, and then The other hand
touches the front electrode of the
bracelet, three electricExtremely full skin Ra
contact, test, test report The report needs
to be viewed in the APP.
Blood oxygen interface
Switch to the blood oxygen test interface to enter
the blood oxygen real-time detection and
measurement data It can be updated to the APP
synchronously, and there is a test report.
Long press to enter sport mode detection.
There are multiple sport modes to choose from.
Long press to enter sport mode, click to switch modes
long press to start calculation, long press to stop.
OLD
Motion interface es
Brightness adjustment page
On the brightness adjustment page, press
and hold the touch key to adjust the screen
brightness.
Restore page
touch key to restore the bracelet.
Shutdown page
On the shutdown page, long press the
bracelet for more than three seconds to
shake off.
Back to page
On the return interface, press and hold
the touch key to return to the previous menu.
Other feature reminders
The reminder function needs to be set to enable the reminder
switch on the APP side, and keep the mobile phone and the
bracelet connected successfully in Bluetooth. The message
is a vibration reminder.
Precautions
4.Do not use an adapter with a current over 2A. Charging time is
around 2~3 hours
2.Do not charge after the device was water damaged
3.This is an electronic monitoring product, data received from it
cannot be used as medical basis.
: f
4 Blood pressure testing tip: {|
a)Keep your body relaxed and still while testing. = + )
b)Keep device at the same height as your heart, A |
Loa
and don't talk while you are testing
OELD