www.teknikoffice.co.uk

Teknik

Sit and surf .

Computer Workcentre

5401562

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

Table of Contents

Part Identifi cation

Hardware Identifi cation

Assembly Steps

Français

Español

Safety

Warranty

21-24

25-28

29-30

31

2-3

3-4

5-16

Assembly Tools Required

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Hammer

Not actual size

Skip the power trip.

This time.

Part Identifi cation

A RIGHT END (1)

B LEFT END (1)

C UPRIGHT (1)

D TOP (1)

D28 RIGHT DRAWER SIDE (2)

D29 LEFT DRAWER SIDE (2)

D78 DRAWER BACK (2)

D707 DRAWER BOTTOM (2)

E MODESTY PANEL (1)

F BACK (1)

G BRACE (1)

H KEYBORAD SHELF (1)

I KEYBOARD FRONT (1)

J KEYBOARD BACK (1)

K KEYBOARD SIDE (2)

L DRAWER FRONT (2)

Q END MOLDING (1)

R BASE (1)

Page 2

Part Identifi cation

Now you know our ABCs.

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.

D

F

A

D78

D29

D28

D707

E

C

L

G

R

D78

D28

B

Q

D707

D29

J

H

K L

K I

Hardware Identifi cation

35GA CABINET RIGHT - 2 35GB CABINET LEFT - 2 35GC DRAWER RIGHT - 2 35GD DRAWER LEFT - 2

35AW CABINET RIGHT - 1 35AX CABINET LEFT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1

Page 3

Hardware Identifi cation

å Screws are shown actual size. You may receive extra hardware with your unit.

15B FILE GLIDE - 4 BB2 HIDDEN CAM - 10 CC2 CAM DOWEL - 10 DD ANGLE BRACKET - 7 EE

EXTENSION

BRACKET - 2

GG HINGE - 2 HH CATCH - 1 II LATCH - 1 JJ BARREL NUT - 1 KK PULL MOUNT - 6

LL PULL - 3 MM SLIDE CAM - 4 NN METAL PIN - 3 OO BLACK 1-7/8" FLAT HEAD SCREW - 2

30S BLACK 1-9/16" FLAT HEAD SCREW - 8

QQ BLACK 1-1/16" MACHINE SCREW - 1

SS SILVER 5/8" MACHINE SCREW - 6

UU BLACK 9/16" PAN HEAD SCREW - 1

WW GOLD 5/16" FLAT HEAD SCREW - 20

Page 4

PP BLACK 1-1/4" FLAT HEAD SCREW - 6

RR BROWN 1" FLAT HEAD SCREW - 4

TT BLACK 9/16" LARGE HEAD SCREW - 18

VV BROWN 7/16" LARGE HEAD SCREW - 8

XX NAIL - 15

Step 1

å

Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor.

å

Push ten HIDDEN CAMS (BB2) into the ENDS (A and B),

UPRIGHT (C), MODESTY PANEL (E), and BRACE (G). Then insert a CAM DOWEL (CC2) into each HIDDEN CAM.

Do not tighten the HIDDEN CAMS in this step.

CC2

(10 used)

(10 used)

Arrow

BB2

E

G

C

B

Arrow

A

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Page 5

Step 2

å

Fasten the CABINET RIGHTS (35GA) to the RIGHT END (A) and a CABINET LEFTS (35GB) to the UPRIGHT (C). Use four

GOLD 5/16" FLAT HEAD SCREWS (WW) through holes #1 and #3.

å

Fasten the CABINET RIGHT (35AW) to the opposite surface of the UPRIGHT (C).

å

NOTE: Be sure the roller end of each RAIL is at the same end.

Remember:

Righty tighty.

Lefty loosey.

Roller end

Sur face with

HIDDEN CAMS

3

2

A

1

Sur face with

HIDDEN CAMS

1

2

C

3

1

Roller end

These holes must be here.

2

3

3

2

1

These holes must be here.

WW

GOLD 5/16" FLAT HEAD SCREW

(10 used in this step)

Page 6

Step 3

å

Fasten seven ANGLE BRACKETS (DD) to the ENDS (A and B) and UPRIGHT (C). Use seven BLACK 9/16" LARGE

HEAD SCREWS (TT).

å

NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS and UPRIGHT.

å

Fasten the END MOLDING (Q) to the LEFT END (B). Use three BLACK 9/16" LARGE HEAD SCREWS (TT).

å

NOTE: There are no pre-drilled holes in the END

MOLDING (Q). Turn the screws into the groove of the END

MOLDING. Do not over tighten.

TT

BLACK 9/16" LARGE HEAD SCREW

(10 used in this step)

(7 used)

DD

Sur

HIDDEN CAMS

C

Q

Sur

HIDDEN CAMS

B

A

Sur

HIDDEN CAMS

DD

Groove

Page 7

Step 4

å

Insert a METAL PIN (NN) into the hole in the TOP (D).

Fasten the END (B) to the TOP. Tighten two HIDDEN CAMS.

å

NOTE: Be sure the PIN in the TOP inserts into the edge of the END.

å

Fasten the MODESTY PANEL (E) to the END (B). Tighten two HIDDEN CAMS.

E

Notch

Sur face with HIDDEN CAMS

D

B

Sur

HIDDEN CAMS

NN

Caution

Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN

CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten:

Page 8

Start

Arrow

Tighten

Maximum

210 degrees

Minimum

190 degrees

Arrow

Step 5

å

Fasten the UPRIGHT (C) to the MODESTY PANEL (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (OO).

å

Insert two METAL PINS into the short edges of the BRACE (G).

å

Fasten the BRACE (G) to the UPRIGHT (C). Tighten one

HIDDEN CAM.

å

NOTE: Be sure the METAL PIN in the BRACE inserts into the hole in the UPRIGHT. You may need to hold the BRACE up until the RIGHT END is fastened in the next step.

G

Sur face with

HIDDEN CAMS

C

Sur

HIDDEN CAMS

E

D

OO

BLACK 1-7/8" FLAT HEAD SCREW

(2 used in this step)

Maximum

210 degrees

Minimum

190 degrees

Arrow

Page 9

Step 6

å

Fasten the RIGHT END (A) to the TOP (D). Fasten two

HIDDEN CAMS.

å

Fasten the RIGHT END (A) to the BRACE (G). Tighten the

HIDDEN CAM.

å

NOTE: Be sure the PIN in the BRACE inserts into the hole in the END.

å

Fasten the BASE (R) to the RIGHT END (A) and UPRIGHT (C).

Use four BLACK 9/16" LARGE HEAD SCREWS (TT).

TT

BLACK 9/16" LARGE HEAD SCREW

(4 used in this step)

Maximum

210 degrees

Minimum

190 degrees

Arrow

G

C

R

Curved edge

A

D

Page 10

Step 7

å

Fasten two EXTENSION BRACKETS (EE) to the LEFT END (B).

Use four BLACK 9/16" LARGE HEAD SCREWS (TT).

å

Fasten the CABINET LEFT (35AX) to the EXTENSION

BRACKETS (EE). Use two GOLD 5/16" FLAT HEAD

SCREWS (WW) through holes #1 and #2.

TT

BLACK 9/16" LARGE HEAD SCREW

(4 used in this step)

B

2

1

Roller end

EE

WW

GOLD 5/16" FLAT HEAD SCREW

(2 used in this step)

Page 11

Step 8

å

Carefully turn your unit over onto its front edges. Lay the

BACK (F) over your unit.

å

Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”.

å

Fasten the BACK (F) to your unit using the NAILS (XX).

Caution

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Page 12

BACK edge without holes

F

Finished sur face

NAIL

(15 used in this step)

XX

Step 9

å

Fasten the KEYBOARD SIDES (K) and KEYBOARD BACK (J) to the KEYBOARD SHELF (H). Use four 1-1/4" FLAT

HEAD SCREWS (PP).

å

Fasten the KEYBOARD SIDES (K) to the KEYBOARD

BACK (J). Use two 1-1/4" FLAT HEAD SCREWS (PP).

K

These surfaces should have the same fi nish.

PP

Long fi nished edge

Finished sur

H

face

J

PP

BLACK 1-1/4" FLAT HEAD SCREW

(6 used in this step)

K

PP

Page 13

Step 10

å

Fasten the CATCH (HH) to the KEYBOARD FRONT (I).

Use a 9/16" PAN HEAD SCREW (UU).

å

To fasten the LATCH (II) to the KEYBOARD SHELF (H), insert the BLACK 1-1/16" MACHINE SCREW (QQ) through the

LATCH and KEYBOARD SHELF. Turn the BARREL NUT (JJ) onto the end of the SCREW. Use two screwdrivers to tighten the SCREW and NUT.

å

Fasten the HINGES (GG) to KEYBOARD SHELF (H) and

KEYBOARD FRONT (I). Use eight BROWN 5/16" LARGE

HEAD SCREWS (VV).

VV

BROWN 7/16" LARGE HEAD SCREW

(8 used in this step)

UU

BLACK 9/16" PAN HEAD SCREW

(1 used in this step)

HH

GG

II

I

H

I

QQ JJ

BLACK 1-1/16" MACHINE SCREW BARREL NUT

(1 used of each to attach the LATCH)

Page 14

Step 11

å

Fasten the DRAWER RIGHT (35AY) and the DRAWER

LEFT (35AZ) to the KEYBOARD SHELF (H). Use four

BROWN 1" FLAT HEAD SCREWS (RR).

Roller end

H

Side Step: Make nachos. (Optional, but recommended.)

Roller end

RR

BROWN 1" FLAT HEAD SCREW

(4 used in this step)

Page 15

Step 12

1

The tabs should insert freely into the slots. Gently tilt the

DRAWER SIDES side to side until the tabs slip into the slots.

2

Unfi sur

nished face

D707

With the palm of your hand, tap the DRAWER

BOTTOM down into the groove.

D28

D28

D29

D29

L

L

Groove

å

Insert the DRAWER SIDES (D28 and D29) at an angle into the slot at each end of the DRAWER FRONT (L).

3

å

Be sure the DRAWER

BOTTOM inserts into the

DRAWER FRONT groove.

Slide the DRAWER BOTTOM (D707) into the grooves in the

DRAWER SIDES (D28 and D29) and DRAWER FRONT (L).

Be sure the

DRAWER

BOTTOM inserts into the DRAWER

BACK groove.

D28

D707

D78

Start each screw a few turns before completely tightening any of them.

30S

BLACK 1-9/16" FLAT HEAD SCREW

(8 used in this step)

D29

å

å

Fasten the DRAWER BACK (D78) to the DRAWER SIDES (D28 and D29). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S).

å

NOTE: Be sure the DRAWER BOTTOM (D707) inserts into the groove of the DRAWER BACK (D78).

Repeat this step for the remaining drawer.

Page 16

Step 13

å

Insert a SLIDE CAM (MM) into the DRAWER

SIDES (D28 and D29).

å

Fasten a DRAWER RIGHT (35GC) to the DRAWER RIGHT

SIDE (D28) and a DRAWER LEFT (35GD) to the DRAWER

LEFT SIDE (D29). Use four GOLD 5/16" FLAT HEAD

SCREWS (WW) through holes #1 and #3.

å

NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE.

å

Push the FILE GLIDES (15B) onto the top edges of the

DRAWER SIDES (D28 and D29).

å

Repeat this step for the remaining drawer.

3

2

1

Roller end

MM

15B

D29

15B

D28

Screw head - turn CAM to line up holes in the SLIDES with holes in DRAWER SIDES

MM

Roller end

1

WW

GOLD 5/16" FLAT HEAD SCREW

(8 used in this step)

3

2

Page 17

Step 14

å

Fasten two PULL MOUNTS (KK) and a PULL (LL) to each

DRAWER FRONT (I and L). Use six SILVER 5/8" MACHINE

SCREWS (SS).

å

Repeat this step for the remaining drawer.

KK

LL

KK

SS

SILVER 5/8" MACHINE SCREW

(6 used for the PULLS)

I

L

Page 18

Step 15

å

Carefully stand your unit upright.

å

To insert the drawers into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit.

Repeat this step to insert the KEYBOARD SHELF (H).

å

To make adjustments to the KEYBOARD FRONT (I), loosen the

SCREWS in the HINGES (GG), make needed adjustments, and tighten the SCREWS.

If you're doing this to help a friend, don't leave without a bite.

Place the roller on the SLIDE behind the roller on the RAIL.

GG

H

25 lbs.

I

70 lbs.

25 lbs.

25 lbs.

Page 19

Step 16

å

To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when fi nished with adjustments.

å

NOTE: Please read the back pages of the instruction booklet for important safety information.

å

This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.

Loosen screw #3 a 1/4 turn, turn the cam a 1/4 turn maximum in both the clockwise and counter-clockwise directions to make adjustments, and then tighten screw #3.

The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front.

Cam

Page 20

WARNING

Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart.

What can happen: How to avoid the problem: Look out for:

• Overloaded shelves and drawers.

• Improper loading can cause the product to be top-heavy.

• Risk of injury.

• Top-heavy furniture can tip over.

• Overloaded shelves and drawers can break.

• Never exceed the weight limits shown in the instructions.

• Work from bottom to top when loading shelves and drawers. Place the heavier items on the lower shelves or in lower drawers.

• Improperly moving furniture that is not designed and equipped with casters.

• Placing TVs on furniture items that are not designed to support a television is hazardous.

• Furniture can tip over or break if improperly moved.

• Physical injury. Furniture can be very heavy.

• Breakage of tops - particularly with double pedestal furniture (drawers at both ends).

• Unload shelves and drawers from top to bottom before moving the unit.

• Do not push furniture, especially on a carpeted fl oor. Have a friend help you lift the item and set it in place.

• Provide support to the center section of the top when lifting the furniture.

• Risk of injury or death. TVs can be very heavy. Plus the weight and location of the picture tube tends to make TVs unbalanced and prone to tipping forward.

• This product is not designed to support a television.