STMicroelectronics TS1871 Datasheet
Advertisement
Advertisement
TS187x, TS187xA
1.8 V input/output, rail-to-rail, low power operational amplifiers
Datasheet — production data
Features
■
■
■
■
■
■
■
■
■
Operating range from V
CC
= 1.8 to 6 V
Rail-to-rail input and output
Extended V icm
(V
CC-
- 0.2 V to V
CC+
+ 0.2 V)
Low supply current (400 µA)
Gain bandwidth product (1.6 MHz)
High unity gain stability
ESD tolerance (2 kV)
Latch-up immunity
Available in
– SOT23-5 micropackage
– MiniSO-8, SO-8, SO-14
– TSSOP8, TSSOP14 package
Applications
■
■
■
■
Battery powered applications (toys)
Portable communication devices (cell phones)
Audio drivers (headphone drivers)
Laptop/notebook computers
Description
The TS187x (single, dual and quad) device can operate with voltages as low as 1.8 V. They feature both input and output rail-to-rail.
The common mode input voltage extends 200 mV beyond the supply voltages at 25 °C, while the output voltage swing is within 100 mV of each rail with a 600 Ω load resistor. The devices consume typically 400 µA per channel while offering
1.6 MHz of gain bandwidth product. The amplifiers provide a high output drive capability at typically 65 mA loads.
These features make the TS187x family ideal for sensor interface, battery supplied and portable applications.
TS1871ILT
Out 1
V
CC-
2
In+
3
5 V
CC+
4 In-
TS1871ID/IDT
N.C.
In-
In+
V
CC-
3
4
1
2 _
+
6
5
8
7
N.C.
V
CC+
Out
N.C.
TS1872ID/IDT-TS1872IST-TS1872IPT
TS1874ID/IDT-TS1874IPT
+
_
+
_
Table 1.
Reference
Device summary
Single version
Dual version
TS187x
TS187xA
TS1871
TS1871A
TS1872
TS1872A
Quad version
TS1874
TS1874A
November 2012
This is information on a product in full production.
Doc ID 6992 Rev 7 1/25 www.st.com
25
Contents
Contents
TS187x, TS187xA
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3
SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TSSOP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MiniSO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SO-14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SOT23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/25 Doc ID 6992 Rev 7
TS187x, TS187xA
1
Absolute maximum ratings and operating conditions
Absolute maximum ratings and operating conditions
Table 2.
Symbol
V
CC
V id
V
T
R
T in stg j thja
Absolute maximum ratings
Parameter
Supply voltage
(1)
Differential input voltage
(2)
Input voltage
Storage temperature
Maximum junction temperature
Thermal resistance junction-to-ambient
(3)
SOT23-5
MiniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
Value
7
±1
V
CC-
-0.3 to V
CC+
+0.3
-65 to +150
150
250
190
125
103
120
100
Unit
V
V
V
°C
°C
°C/W
R thjc
ESD
Thermal resistance junction-to-case
SOT23-5
MiniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
HBM: human body model
(4)
MM: machine model
(5)
CDM: charged device model
(6)
Latch-up immunity
81
39
40
31
37
32
2
200
1.5
200
°C/W
Lead temperature (soldering, 10 sec.)
Output short-circuit duration
250
See
(7)
°C
1.
All voltage values, except differential voltage, are with respect to network terminal.
2.
Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
If V id
> ±1 V, the maximum input current must not exceed ±1 mA. When V id
> ±1 V, add an input series resistor to limit the input current.
3.
Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all amplifiers.
4.
Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 k
Ω resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
5.
Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω ). This is done for all couples of connected pin combinations while the other pins are floating.
6.
Charged device model: all pins and package are charged together to the specified voltage and then discharged directly to ground through only one pin. This is done for all pins.
7.
Short-circuits from the output to V
CC can cause excessive heating. The maximum output current is approximately 80 mA, independent of the magnitude of V
CC
. Destructive dissipation can result from simultaneous short-circuits on all amplifiers.
kV
V kV mA
Doc ID 6992 Rev 7 3/25
Absolute maximum ratings and operating conditions
Table 3.
Symbol
V
CC
V icm
T oper
Operating conditions
Parameter
Supply voltage
Common-mode input voltage range
T oper
= 25 °C, 1.8
≤ V
CC
≤ 6 V
T min
< T oper
< T max
, 1.8
≤ V
CC
≤ 6 V
Operating free air temperature range
TS187x, TS187xA
Value
1.8 to 6
V
CC-
- 0.2 to V
CC+
+ 0.2
V
CC-
to V
CC+
-40 to + 125
Unit
V
V
°C
4/25 Doc ID 6992 Rev 7
TS187x, TS187xA Electrical characteristics
Table 4.
Electrical characteristics measured at V
CC+ connected to V
CC
/2, and T amb
= +1.8 V with V
CC-
= 0 V, C
= 25 °C (unless otherwise specified)
(1)
L and R
L
Parameter Conditions Min.
Typ.
Max.
Unit Symbol
V io
Input offset voltage
V icm
= V out
= V
CC
/2
TS1871A/2A/4A
T min
≤
T amb
T max
TS1871/2/4
T min
≤
T amb
T max
Δ
V io
Input offset voltage drift
A
V
V
I
I
I
I io ib
CMR vd
OH
OL o
CC
Input offset current
Input bias current
Common mode rejection ratio
20 log (
Δ
V ic
/
Δ
V io
)
Large signal voltage gain
High level output voltage
Low level output voltage
Output source current
Output sink current
Supply current (per amplifier)
GBP Gain bandwidth product
SR
φ m
Slew rate
Phase margin e n
Input voltage noise
THD Total harmonic distortion
V icm
= V out
= V
CC
/2
(2)
T min
≤
T amb
≤
T max
V icm
= V out
= V
CC
/2
(2)
T min
≤
T amb
T max
0
≤
V icm
≤
V
CC,
V out
= V
CC
/2
T min
≤
T amb
T max
V out
= 0.5 to 1.3 V
R
L
R
L
= 2 k
Ω
= 600
Ω
V id
= 100 mV
R
L
R
L
= 2 k
Ω
= 600
Ω
T min
≤
T amb
≤
T
T min
≤
T amb
≤
T max,
R
L
= 2 k
Ω max,
R
L
= 600
Ω
V id
= -100 mV
R
L
R
L
= 2 k
Ω
= 600
Ω
T min
≤
T amb
≤
T max,
R
L
= 2 k
Ω
T min
≤
T amb
≤
T max,
R
L
= 600
Ω
V id
= 100 mV, V
O
= V
CC-
V id
= -100 mV, V
O
= V
CC+
V out
= V
CC
/2
A
VCL
= 1, no load
T min
≤
T amb
T max
R
L
= 10 k
Ω
, C
L
= 100 pF, f = 100 kHz
R
L
= 10 k
Ω
, C
L
= 100 pF, A
V
= 1
C
L
= 100 pF f = 1 kHz
1.
All parameter limits at temperatures different from 25 °C are guaranteed by correlation.
2.
Maximum values include unavoidable inaccuracies of the industrial tests.
55
52
77
70
1.65
1.62
1.65
1.62
20
20
0.1
2
3
40 125
150
77
30
60
1
1.5
3
6
91
84
1.77
1.74
30
46
58
68
100
150
100
150
400 560
600
0.9
1.6
0.38
0.54
53
27
0.01
mV
µV/°C nA nA dB dB
V mV mA
µA
MHz
V/µs
Degrees nV/
√
Hz
%
Doc ID 6992 Rev 7 5/25
Electrical characteristics TS187x, TS187xA
Table 5.
Electrical characteristics measured at V to V
CC
/2, and T amb
CC
= +3 V with V
= 25 °C (unless otherwise specified)
CC-
(1)
= 0 V, C
L and R
L
connected
Parameter Conditions Min.
Typ.
Max.
Unit Symbol
V io
Input offset voltage
V icm
= V out
= V
CC
/2
TS1871A/2A/4A
T min
≤
T amb
≤
T max
TS1871/2/4
T min
≤
T amb
≤
T max
Δ
V io
Input offset voltage drift
A
V
V
I
I
I
I io ib
CMR vd
OH
OL o
CC
Input offset current
Input bias current
Common mode rejection ratio
20 log (
Δ
V ic
/
Δ
V io
)
Large signal voltage gain
High level output voltage
Low level output voltage
Output source current
Output sink current
Supply current (per amplifier)
GBP Gain bandwidth product
SR
φ m
Slew rate
Phase margin e n
Input voltage noise
THD Total harmonic distortion
V icm
= V out
= V
CC
/2
(2)
T min
≤
T amb
≤
T max
V icm
= V out
= V
CC
/2
(2)
T min
≤
T amb
≤
T max
0
≤
V icm
≤
V
CC,
V out
= V
CC
/2
T min
≤
T amb
≤
T max
V out
= 0.5 to 2.5 V
R
L
R
L
= 2 k
Ω
= 600
Ω
V id
= 100 mV
R
L
R
L
= 2 k
Ω
= 600
Ω
T min
≤
T amb
≤
T max
, R
L
= 2 k
Ω
T min
≤
T amb
≤
T max
, R
L
= 600
Ω
V id
= -100 mV
R
L
R
L
= 2 k
Ω
= 600
Ω
T min
≤
T amb
≤
T max,
T min
≤
T amb
≤
T max,
R
L
= 2 k
Ω
R
L
= 600
Ω
V id
= 100 mV, V
O
= V
CC-
V id
= -100 mV, V
O
= V
CC+
V out
= V
CC
/2
A
VCL
= 1, no load
T min
≤
T amb
≤
T max
R
L
= 10 k
Ω
, C
L
= 100 pF, f = 100 kHz
R
L
= 10 k
Ω
, C
L
= 100 pF, A
V
= 1
C
L
= 100 pF f = 1 kHz
1.
All parameter limits at temperatures different from 25 °C are guaranteed by correlation.
2.
Maximum values include unavoidable inaccuracies of the industrial tests.
60
57
80
74
2.82
2.80
2.82
2.80
2.95
2.95
20
20
0.1
2
3
4
80
94
88
39
58
60
70
1
1.5
3
6
30
60
125
150
120
160
120
160 mV
µV/°C nA nA dB dB
V mV mA
450 650
690
1 1.7
0.42
0.6
53
27
0.01
µA
MHz
V/µs
Degrees nV/
√
Hz
%
6/25 Doc ID 6992 Rev 7
TS187x, TS187xA Electrical characteristics
Table 6.
Electrical characteristics measured at V to V
CC
/2, and T amb
CC
= +5 V with
= 25 °C (unless otherwise specified)
V
CC-
(1)
= 0 V, C
L and R
L
connected
Parameter Conditions Min.
Typ.
Max.
Unit Symbol
V io
Input offset voltage
V icm
= V out
= V
CC
/2
TS1871A/2A/4A
T min
≤
T amb
≤ max
TS1871/2/4
T min
≤
T amb
≤
T max
Δ
V io
Input offset voltage drift
I
I io ib
Input offset current
Input bias current
V icm
= V out
= V
CC
/2
(2)
T min
≤
T amb
≤ max
V icm
= V out
T min
≤
T amb
= V
CC
/2
(2)
≤
T max
0
≤
V icm
≤
V
CC,
V out
not equal to V
CC
/2
T min
≤
T amb
≤ max
CMR
SVR
Common mode rejection ratio
20 log (
Δ
V ic
/
Δ
V io
)
Supply voltage rejection ratio
20 log (
Δ
V cc
/
Δ
V io
)
V
CC
= 1.8 to 5 V
A
V
V
I
I vd
OH
OL o
CC
Large signal voltage gain
High level output voltage
Low level output voltage
Output source current
Output sink current
Supply current (per amplifier)
GBP Gain bandwidth product
SR
φ m
Slew rate
Phase margin e n
Input voltage noise
THD Total harmonic distortion
V out
= 1 to 4 V
R
L
R
L
= 2 k
Ω
= 600
Ω
V id
= 100 mV
R
L
R
L
= 2 k
Ω
= 600
Ω
T min
≤
T amb
T min
≤
T amb
≤
T max
, R
L
= 2 k
Ω
≤
T max
, R
L
= 600
Ω
V id
= -100 mV
R
L
R
L
= 2 k
Ω
= 600
Ω
T min
≤
T amb
T min
≤
T amb
≤ max,
R
L
= 2 k
Ω
≤
T max,
R
L
= 600
Ω
V id
= 100 mV, V
O
= V
CC-
V id
= -100 mV, V
O
= V
CC+
V out
= V
CC
/2
A
VCL
= 1, no load
T min
≤
T amb
≤ max
R
L
= 10 k
Ω
, C
L
= 100 pF, f = 100 kHz
R
L
= 10 k
Ω
, C
L
= 100 pF, A
V
= 1
C
L
= 100 pF f = 1 kHz
1.
All parameter limits at temperatures different from 25 °C are guaranteed by correlation.
2.
Maximum values include unavoidable inaccuracies of the industrial tests.
65
62
70
83
77
4.80
4.75
4.80
4.75
20
20
0.1
2
3
90
97
91
4.95
4.90
52
70
65
80
1
1.5
3
6
30
60
70 130
85
150
130
188
130
188
500 835
875
1 1.8
0.42
0.6
55
27
0.01
mV
µV/°C nA nA dB dB dB
V mV mA
µA
MHz
V/µs
Degrees nV/
√
Hz
%
Doc ID 6992 Rev 7 7/25
Electrical characteristics
Figure 1.
Input offset voltage distribution
TS187x, TS187xA
Figure 2.
Input offset voltage vs. temperature
Figure 3.
Input bias current vs. temperature at V
CC
= 1.8 V
Figure 4.
Input bias current vs. temperature at V
CC
= 3 V
Figure 5.
Supply current/amplifier vs. supply voltage
Figure 6.
Supply current/amplifier vs. temperature
8/25 Doc ID 6992 Rev 7
TS187x, TS187xA
Figure 7.
Common mode rejection vs. temperature
Electrical characteristics
Figure 8.
Supply voltage rejection vs. temperature at V
CC
= 1.8 V
Figure 9.
Supply voltage rejection vs. temperature at V
CC
= 3 V
Figure 10.
Supply voltage rejection vs. temperature at V
CC
= 5 V
Figure 11.
Power supply voltage rejection vs. frequency
Figure 12.
Open loop gain vs. temperature at V
CC
= 1.8 V
Doc ID 6992 Rev 7 9/25
Electrical characteristics
Figure 13.
Open loop gain vs. temperature at V
CC
= 3 V
TS187x, TS187xA
Figure 14.
Open loop gain vs. temperature at V
CC
= 5 V
Figure 15.
High level output voltage vs. temperature, R
L
= 600
Ω
Figure 16.
Low level output voltage vs. temperature, R
L
= 600
Ω
Figure 17.
High level output voltage vs. temperature, R
L
= 2 k
Ω
Figure 18.
Low level output voltage vs. temperature, R
L
= 2 k
Ω
10/25 Doc ID 6992 Rev 7
TS187x, TS187xA
Figure 19.
Output current vs. temperature at V
CC
= 1.8 V
Electrical characteristics
Figure 20.
Output current vs. temperature at V
CC
= 3 V
Figure 21.
Output current vs. temperature at V
CC
= 5 V
Figure 22.
Output current vs. output voltage at V
CC
= 1.8 V
Figure 23.
Output current vs. output voltage at V
CC
= 3 V
Figure 24.
Output current vs. output voltage at V
CC
= 5 V
Doc ID 6992 Rev 7 11/25
Electrical characteristics
Figure 25.
Gain and phase vs. frequency at V
CC
= 1.8 V
TS187x, TS187xA
Figure 26.
Gain and phase vs. frequency at V
CC
= 3 V
Figure 27.
Gain and phase vs. frequency at V
CC
= 5 V
Figure 28.
Gain bandwidth product vs. temperature
Figure 29.
Gain bandwidth product vs. supply voltage
Figure 30.
Slew rate vs. temperature at
V
CC
= 1.8 V
12/25 Doc ID 6992 Rev 7
TS187x, TS187xA
Figure 31.
Slew rate vs. temperature at
V
CC
= 3 V
Electrical characteristics
Figure 32.
Slew rate vs. temperature at
V
CC
= 5 V
Figure 33.
Phase margin vs. load capacitor Figure 34.
Phase margin vs. output current
Figure 35.
Gain margin vs. output current Figure 36.
Equivalent input noise vs. frequency
Doc ID 6992 Rev 7 13/25
Electrical characteristics
Figure 37.
Distortion vs. output voltage at V
CC
= 1.8 V
TS187x, TS187xA
Figure 38.
Distortion vs. output voltage at V
CC
= 3 V
Figure 39.
Distortion vs. output voltage at V
CC
= 5 V
Figure 40.
Distortion vs. output voltage at V
CC
= 2.7 V, R
L
= 150
Ω
Figure 41.
Distortion vs. output voltage at V
CC
= 2.7 V, R
L
= 1500
Ω
Figure 42.
Distortion vs. output voltage at V
CC
= 2.7 V, R
L
= 4700
Ω
14/25 Doc ID 6992 Rev 7
TS187x, TS187xA
Figure 43.
Distortion vs. frequency at V
CC
= 1.8 V
Electrical characteristics
Figure 44.
Distortion vs. frequency at V
CC
= 3 V
Figure 45.
Distortion vs. frequency at V
CC
= 1.8 V, R
L
= 32 Ω
Figure 46.
Distortion vs. frequency at V
CC
= 3 V, R
L
= 32 Ω
Figure 47.
Output power vs. supply voltage Figure 48.
Common mode rejection ratio vs. frequency at V
CC
= 5 V
Doc ID 6992 Rev 7 15/25
Package information TS187x, TS187xA
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com
. ECOPACK is an ST trademark.
16/25 Doc ID 6992 Rev 7
TS187x, TS187xA
3.1 SO-8 package information
Figure 49.
SO-8 package outline
Package information
Table 7.
Symbol
SO-8 package mechanical data
Dimensions
Millimeters
Min.
Typ.
Max.
1.75
0.25
Min.
D
E
E1 e h
L
L1 k ccc
A
A1
A2 b c
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.25
0.40
1°
4.90
6.00
3.90
1.27
1.04
0.48
0.23
5.00
6.20
4.00
0.50
1.27
8°
0.10
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.010
0.016
1°
Doc ID 6992 Rev 7
Inches
Typ.
0.193
0.236
0.154
0.050
0.040
Max.
0.069
0.010
0.019
0.010
0.197
0.244
0.157
0.020
0.050
8°
0.004
17/25
Package information
3.2 TSSOP8 package information
Figure 50.
TSSOP8 package outline
TS187x, TS187xA
18/25 c
D
E
E1
A
A1
A2 b e k
L
L1 aaa
Table 8.
Symbol
TSSOP8 package mechanical data
Dimensions
Min.
Millimeters
Typ.
Min.
0.05
0.80
0.19
0.09
2.90
6.20
4.30
1.00
3.00
6.40
4.40
0.65
Max.
0.20
3.10
6.60
4.50
1.20
0.15
1.05
0.30
0.002
0.031
0.007
0.004
0.114
0.244
0.169
0°
0.45
0.60
1
8°
0.75
0°
0.018
0.10
Doc ID 6992 Rev 7
Inches
Typ.
0.039
0.118
0.252
0.173
0.0256
0.024
0.039
Max.
0.047
0.006
0.041
0.012
0.008
0.122
0.260
0.177
8°
0.030
0.004
TS187x, TS187xA
3.3 MiniSO-8 package information
Figure 51.
MiniSO-8 package outline
Package information e
L
L1
L2 k ccc c
D
E
E1
A
A1
A2 b
Table 9.
Symbol
MiniSO-8 package mechanical data
Dimensions
Min.
Millimeters
Typ.
Min.
0
0.75
0.22
0.08
2.80
4.65
2.80
0.40
0.85
3.00
4.90
3.00
0.65
0.60
0.95
0.25
Max.
0.23
3.20
5.15
3.10
1.1
0.15
0.95
0.40
0.80
0
0.030
0.009
0.003
0.11
0.183
0.11
0.016
0° 8°
0.10
0°
Doc ID 6992 Rev 7
Inches
Typ.
0.033
0.118
0.193
0.118
0.026
0.024
0.037
0.010
Max.
0.043
0.006
0.037
0.016
0.009
0.126
0.203
0.122
0.031
8°
0.004
19/25
Package information
Figure 52.
SO-14 package outline
TS187x, TS187xA
20/25
E e
C
D
A
A1
A2
B
L k
H h ddd
Table 10.
SO-14 package mechanical data
Dimensions
Symbol Millimeters
Min.
Typ.
Max.
Min.
1.35
0.10
1.10
0.33
1.75
0.25
1.65
0.51
0.19
8.55
3.80
0.25
8.75
4.0
0.007
0.33
0.15
5.80 6.20
0.25
0.50
0.40
1.27
1.27
0.22
0.009
8° (max.)
0.015
0.10
0.05
0.004
0.04
0.01
Inches
Typ.
0.05
0.24
0.02
0.05
0.004
Max.
0.068
0.009
0.06
0.02
0.009
0.34
0.15
Doc ID 6992 Rev 7
TS187x, TS187xA
Figure 53.
TSSOP14 package outline
Package information c
D
E
E1
A
A1
A2 b e
L
L1 k aaa
Table 11.
TSSOP14 package mechanical data
Dimensions
Symbol
Min.
Millimeters
Typ.
Min.
0.05
0.80
0.19
0.09
4.90
6.20
4.30
0.45
1.00
5.00
6.40
4.40
0.65
0.60
1.00
Max.
0.20
5.10
6.60
4.50
1.20
0.15
1.05
0.30
0.75
0.002
0.031
0.007
0.004
0.193
0.244
0.169
0.018
0° 8°
0.10
0°
Inches
Typ.
0.004
0.039
0.197
0.252
0.173
0.0256
0.024
0.039
Max.
0.047
0.006
0.041
0.012
0.0089
0.201
0.260
0.176
0.030
8°
0.004
Doc ID 6992 Rev 7 21/25
Package information
3.6 SOT23-5 package information
Figure 54.
SOT23-5L package outline
TS187x, TS187xA
22/25
B
C
D
D1 e
A
A1
A2
E
F
L
K
Table 12.
SOT23-5L package mechanical data
Dimensions
Symbol Millimeters
Min.
0.90
2.60
1.50
0.10
0°
0.90
0.35
0.09
2.80
Typ.
1.20
1.05
0.40
0.15
2.90
1.90
0.95
2.80
1.60
0.35
Max.
1.45
0.15
1.30
0.50
0.20
3.00
3.00
1.75
0.60
10°
Min.
0.035
0.035
0.013
0.003
0.110
0.102
0.059
0.004
Inches
Typ.
0.047
0.041
0.015
0.006
0.114
0.075
0.037
0.110
0.063
0.013
Max.
0.057
0.006
0.051
0.019
0.008
0.118
0.118
0.069
0.023
Doc ID 6992 Rev 7
TS187x, TS187xA Ordering information
Table 13.
Order codes
Order code Temperature range Package Packaging Marking
TS1871ID/IDT
TS1871IAID/AIDT
SO-8
Tube or tape and reel
1871I
1871AI
TS1871ILT
TS1871AILT
TS1871IYLT
(1)
TS1871AIYLT
TS1872ID/IDT
TS1872AID/AIDT
SOT23-5L
SOT23-5L
(automotive grade)
SO-8
SO-8
(automotive grade)
Tape and reel
Tape and reel
Tube or tape and reel
K171
K172
K182
K183
1872I
TS1872IPT
TS1872AIPT
TS1872IYPT
TS1872AIYPT
TS1872IST
TS1872AIST
-40 °C to +125 °C
TSSOP8
TSSOP8
(automotive grade)
Tube or tape and reel
Tape and reel
Tape and reel
1872AI
1872Y
1872AY
1872I
1872A
1872Y
MiniSO-8 Tape and reel
872AY
K171
K172
TS1874ID/IDT
TS1874AID/AIDT
SO-14
SO-14
(automotive grade)
Tube or tape and reel
Tape and reel
1874I
1874AI
TS1874Y
TS1874IPT
TS1874AIPT
TS1874IYPT
TS1874AIYPT
TSSOP14
TSSOP14
(automotive grade)
Tape and reel
Tape and reel
TS1874AY
1874I
1874AI
TS1874Y
TS1874AY
1.
Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q 002 or equivalent.
Doc ID 6992 Rev 7 23/25
Revision history TS187x, TS187xA
Table 14.
Document revision history
Date Revision
01-Apr-2002
02-Jan-2005
21-May-2007
17-Jan-2008
12-Mar-2010
06-Jul-2012
19-Nov-2012
1
2
3
4
5
6
7
Changes
First release.
Modifications on AMR
(explanation of V id and
V i limits).
Added limits over temperature range in
,
Added SVR in
(SVR parameter removed from
and
Added equivalent input voltage noise in
Added R thjc
values in
.
Added automotive grade part numbers to order codes table.
Moved order codes table to
.
Updated format of package information.
Updated footnote for automotive grade order codes in
Updated document format.
Modified headings, added root part number TS187xA and added
Table 1: Device summary on cover page.
Corrected typical values for A
Vd
, Isource, Isink and Vol in
.
Added Figure 48: Common mode rejection ratio vs. frequency at V
Updated package information in
.
Removed order codes for SO-8 automotive grade packages
(TS1871IYDT and TS1871AIYDT) from
.
Removed order codes for DIP package from
.
Updated Table 13: Order codes .
Updated Features (added MiniSO-8, SO-8, SO-14, TSSOP8,
and TSSOP14 package).
Updated titles of
DD
by V
CC-
).
Updated TS1871IYLT, TS1871AIYLT, TS1872IYDT,
TS1872AIYDT, TS1874IYDT, TS1874AIYDT, TS1874IYPT,
TS1872IYPT, TS1872AIYPT, and TS1874AIYPT order code in
(status qualified).
Updated packaging for TS1874IYDT and TS1874AIYDT order
code (indicated only tape and reel) in Table 13
.
Minor corrections throughout document.
24/25 Doc ID 6992 Rev 7
TS187x, TS187xA
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
Doc ID 6992 Rev 7 25/25
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement