STMicroelectronics LM358A Datasheet
Hirdetés
Hirdetés
LM158, LM258, LM358,
LM158A, LM258A, LM358A
Low-power dual operational amplifiers
Datasheet - production data
Features
Frequency compensation implemented internally
Large DC voltage gain: 100 dB
Wide bandwidth (unity gain): 1.1 MHz
(temperature compensated)
Very low supply current per channel essentially independent of supply voltage
Low input bias current: 20 nA (temperature compensated)
Low input offset voltage: 2 mV
Low input offset current: 2 nA
Input common-mode voltage range includes negative rails
Differential input voltage range equal to the power supply voltage
Large output voltage swing
0 V to (V
CC
+ - 1.5 V)
Related products
See LM158W for enhanced ESD ratings
See LM2904 and LM2904W for automotive grade versions
Description
These circuits consist of two independent, highgain, internally frequency-compensated op amps, specifically designed to operate from a single power supply over a wide range of voltages. The low-power supply drain is independent of the magnitude of the power supply voltage.
Application areas include transducer amplifiers,
DC gain blocks and all the conventional op amp circuits, which can now be more easily implemented in single power supply systems. For example, these circuits can be directly supplied with the standard 5 V, which is used in logic systems and will easily provide the required interface electronics with no additional power supply.
In linear mode, the input common-mode voltage range includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage.
November 2017 DocID2163 Rev 15
This is information on a product in full production.
1/25 www.st.com
Contents LM158, LM258, LM358, LM158A, LM258A,
LM358A
Contents
1 Schematic diagram .......................................................................... 3
2 Package pin connections ................................................................ 4
3 Absolute maximum ratings ............................................................. 5
4 Electrical characteristics ................................................................ 7
5 Electrical characteristic curves ...................................................... 9
6 Typical applications ...................................................................... 13
7 Package information ..................................................................... 16
SO8 package information ................................................................ 17
MiniSO8 package information ......................................................... 18
DFN8 2x2 package information ....................................................... 19
TSSOP8 package information ......................................................... 21
8 Ordering information ..................................................................... 22
9 Revision history ............................................................................ 23
2/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
1 Schematic diagram
Figure 1: Schematic diagram (1/2 LM158)
V
CC
Schematic diagram
Inverting input
Non-inverting input
Q1
Q2 Q3
Q4
C
C
Q10
100 µ A
Q5
Q6
Q7
Q11
Q13
R
SC
Output
Q12
Q8 Q9
GND
DocID2163 Rev 15 3/25
Package pin connections
2
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Package pin connections
Figure 2: Pin connections (top view)
1. The exposed pad of the DFN8 2x2 can be left floating or connected to ground
4/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Absolute maximum ratings
3
Symbol
V
CC
V i
V id
I in
T oper
T stg
T j
R thja
R thjc
ESD
Absolute maximum ratings
Parameter
Table 1: Absolute maximum ratings
LM158,A LM258,A LM358,A Unit
Supply voltage
Input voltage
Differential input voltage
Output short-circuit duration (1)
Operating free-air temperature range
Storage temperature range
Maximum junction temperature
Thermal resistance junction to ambient
Thermal resistance junction to case (3)
SO8
MiniSO8
DFN8 2x2
TSSOP8
SO8
MiniSO8
TSSOP8
±16 or 32
-0.3 to 32
±32
Infinite
5 mA in DC or 50 mA in AC
(duty cycle = 10 %, T = 1 s)
0 to 70 -55 to 125 -40 to 105
-65 to 150
150
125
190
57
120
40
39
37
300
200
1.5
V mA
°C
°C/W
V kV
Notes:
(1)
Short-circuits from the output to V
CC
can cause excessive heating if V
CC
> 15 V. The maximum output current is approximately
40 mA independent of the magnitude of V
CC
. Destructive dissipation can result from simultaneous short circuits on all amplifiers.
(2)
This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward-biased and thereby acting as input diode clamp. In addition to this diode action, there is NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V
CC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. This is not destructive and normal output is restored for input voltages above -0.3 V.
(3)
Short-circuits can cause excessive heating and destructive dissipation. R th
are typical values.
(4)
Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
(5)
Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected pin combinations while the other pins are floating.
(6)
Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins.
DocID2163 Rev 15 5/25
Absolute maximum ratings LM158, LM258, LM358, LM158A, LM258A,
LM358A
Table 2: Operating conditions
Value Unit Symbol Parameter
V
CC
V icm
Supply voltage
Common mode input voltage range T amb
Common mode input voltage range (T min
≤ T amb
≤ T max
3 to 30
(V
CC
-) to (V
CC
+ - 1.5) V
T oper
Operating free air temperature range
LM158
LM258
LM358
(V
CC
-) to (V
CC
+ - 2)
-55 to 125
-40 to 105
0 to 70
°C
Notes:
(1)
When used in comparator, the functionality is guaranteed as long as at least one input remains within the operating common mode voltage range.
(2)
When used in comparator, the functionality is guaranteed as long as at least one input remains within the operating common mode voltage range.
6/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Electrical characteristics
4 Electrical characteristics
Table 3: Electrical characteristics for VCC+ = 5 V, VCC- = Ground, Vo = 1.4 V, Tamb = 25 °C
(unless otherwise specified)
Parameter Min. Typ. Max. Unit Symbol
ΔV
V
I io io io
T
T min min
≤ T
≤ T amb
≤ T amb
≤ T max max
/ΔT Input offset voltage drift
Input offset current
LM158A
LM258A, LM358A
LM158, LM258
LM358
LM158A, LM258A, LM358A
LM158, LM258
LM358
LM158A, LM258A, LM358A
LM158, LM258, LM358
LM158A, LM258A, LM358A
LM158, LM258, LM358
LM158A, LM258A, LM358A
LM158, LM258, LM358
ΔI io
/ΔT
Input offset current drift
LM158A, LM258A, LM358A
LM158, LM258, LM358
LM158A, LM258A, LM358A
LM158, LM258, LM358
I ib
A vd
SVR
I
CC
CMR
Supply voltage rejection ratio
Supply current, all amp, no load
Common mode rejection ratio
LM158A, LM258A, LM358A
I source
T min
≤ T amb
≤ T max
Large signal voltage gain
Output current source
LM158, LM258, LM358
V
CC
+ = 15 V, R
L
= 2 kΩ, V o
= 1.4 V to 11.4 V
T min
≤ T amb
≤ T max
V
CC
+ = 5 V to 30 V, R s
≤ 10 kΩ
T min
≤ T amb
≤ T max
T min
≤ T amb
≤ T max
V
CC
+ = 5 V
T min
≤ T amb
≤ T max
V
CC
+ = 30 V
R s
≤ 10 kΩ
T min
≤ T amb
≤ T max
V
CC
+ = 15 V, V o
= 2 V, V id
= 1 V
I sink
Output sink current
V
CC
+ = 15 V, V o
= 2 V, V id
= -1 V
V
CC
+ = 15 V, V o
= 0.2 V, V id
= -1 V
1
2
7
7
2
2
10
30
30
40
10 200
10 300
20 50
20 150
100
200
50 100
25
65 100
65
70
0.7 1.2
2
85
60
20
10
12
40
20
50
60
5
7
2
3
4
7
9
15
30 mV
µV/°C nA pA/°C nA
V/mV dB mA dB mA mA
µA
DocID2163 Rev 15 7/25
Electrical characteristics LM158, LM258, LM358, LM158A, LM258A,
LM358A
Symbol
V
OH
V
OL
SR
High level output voltage
Low level output voltage
Slew rate
Parameter
V
CC
+ = 30 V, R
L
= 2 kΩ connected to V
CC
-,
T amb
= 25 °C
V
CC
+ = 30 V, R
L
= 2 kΩ connected to V
CC
-,
T min
≤ T amb
≤ T max
V
CC
+ = 30 V, R
L
= 10 kΩ connected to V
CC
-,
T amb
= 25 °C
V
CC
+ = 30 V, R
L
= 10 kΩ connected to V
CC
-,
T min
≤ T amb
≤ T max
V
CC
+ = 5 V, R
L
= 2 kΩ connected to V
CC
-,
T amb
= 25 °C
V
CC
+ = 5 V, R
L
= 2 kΩ connected to V
CC
-,
T min
≤ T amb
≤ T max
R
L
= 10 kΩ connected to V
CC
-
T min
≤ T amb
≤ T max
V
CC
+ = 15 V, V i
= 0.5 to 3 V, R
L
= 2 kΩ,
C
L
= 100 pF, unity gain
Min. Typ. Max. Unit
26
26
27
27
3.5
3
27
28
5
0.3 0.6
20
20
V mV
V/µs
GBP Gain bandwidth product
THD Total harmonic distortion
V
CC
+ = 30 V, f = 100 kHz, V in
= 10 mV,
R
L
= 2 kΩ, C
L
= 100 pF f = 1 kHz, A v
= 20 dB, R
L
= 2 kΩ, V o
= 2 V pp
,
C
L
= 100 pF, V
O
= 2 V pp
0.7 1.1
0.02
MHz
% e n
Equivalent input noise voltage
V o1
/V o2
f = 1 kHz, R s
= 100 Ω, V
CC
+ = 30 V
1 kHz ≤ f ≤ 20 kHz
55
120 dB
Notes:
(1)
V o
= 1.4 V, R s
= 0 Ω, 5 V < V
CC
+
< 30 V, 0 < V ic
< V
CC
+
- 1.5 V
(2)
The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output so there is no change in the load on the input lines.
(3)
Due to the proximity of external components, ensure that stray capacitance between these external parts does not cause coupling. Typically, this can be detected because this type of capacitance increases at higher frequencies.
8/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Electrical characteristic curves
5 Electrical characteristic curves
Figure 3: Open-loop frequency response
140
120
100
80
60
40
VI
10 M
Ω
VCC
VO
VCC/2
+
VCC = 30 V &
-55°C Tamb +125°C
Figure 4: Large signal frequency response
20
-
100 k Ω
+15 V
VO
15 VI
1 k
Ω
+7 V +
2 k Ω
10
5
20
0
1.0
VCC = +10 to +15 V &
-55°C Tamb +125°C
10 100 1k 10k 100k 1M 10M
FREQUENCY (Hz)
0
1k 10k 100k 1M
FREQUENCY (Hz)
Figure 5: Voltage follower pulse response with
VCC = 15 V
Figure 6: Voltage follower pulse response with
VCC = 30 V
5 00 4
3
2
1
0
RL 2 k Ω
VCC = +15 V
4 50
4 00
3 50 e I
-
+ e O
5 0 p F
In p ut
O utput
3
2
1
3 00
2 50
0 1 5
Ta m b = +2 5°C
V C C = 3 0 V
6 7 8
0 10 20 30 40
2 3 4
T IM E (
DocID2163 Rev 15 9/25
Electrical characteristic curves
Figure 7: Input current
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Figure 8: Output voltage vs sink current
Figure 9: Output voltage vs source current Figure 10: Current limiting
10/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Figure 11: Input voltage range
Figure 13: Supply current
160
120
80
40
Electrical characteristic curves
Figure 12: Open-loop gain
RL = 20 k Ω
RL = 2 k
Ω
0 10 20 30 40
POSITIVE SUPPLY VOLTAGE (V)
Figure 14: Input current
Figure 15: Gain bandwidth product Figure 16: Power supply rejection ratio
DocID2163 Rev 15 11/25
Electrical characteristic curves
Figure 17: Common-mode rejection ratio
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Figure 18: Phase margin vs. capacitive load
Phase margin at Vcc = 15 V andVicm = 7.5 V vs. Iout and capacitive load value
50
40 CI = 70 pF
30
20
CI = 290 pF
T = 25 °C
10
Capacitive load values
70 pF, 103 pF, 138 pF, 170 pF, 220 pF, 290 pF
0
-100 0 100 200 300 400 500 600 700 800 900 1000
Iout (µA)
Source for positive values/Sink for negative values
12/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
6 Typical applications
Single supply voltage V
CC
= 5 V
DC
.
Figure 19: AC-coupled inverting amplifier
Typical applications
Figure 20: Non-inverting DC amplifier
Figure 21: AC-coupled non-inverting amplifier Figure 22: DC summing amplifier
DocID2163 Rev 15 13/25
Typical applications
Figure 23: High input Z, DC differential amplifier
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Figure 24: High input Z adjustable gain DC instrumentation amplifier
Figure 25: Using symmetrical amplifiers to reduce input current
Figure 26: Low drift peak detector
µ
Ω
Ω
µ
Ω
Ω
µ
14/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Figure 27: Active band-pass filter
Typical applications
DocID2163 Rev 15 15/25
Package information
7
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com.
ECOPACK ® is an ST trademark.
16/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
7.1 SO8 package information
Figure 28: SO8 package outline
Package information
Ref.
E1 e h
L
L1 k ccc
A
A1
A2 b c
D
E
Min.
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.25
0.40
0°
Table 4: SO8 mechanical data
Dimensions
Millimeters
Typ. Min. Max.
1.75
0.25
4.90
6.00
3.90
1.27
0.48
0.23
5.00
6.20
4.00
0.50
1.27
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.010
0.016
1.04
8°
0.10
0°
Inches
Typ.
0.193
0.236
0.154
0.050
0.040
Max
0.069
0.010
0.019
0.010
0.197
0.244
0.157
0.020
0.050
8°
0.004
DocID2163 Rev 15 17/25
Package information
7.2
LM158, LM258, LM358, LM158A, LM258A,
LM358A
MiniSO8 package information
Figure 29: MiniSO8 package outline
18/25
Ref.
D
E
E1 e
L
L1
L2 k ccc
A
A1
A2 b c
Min.
0.40
0°
0
0.75
0.22
0.08
2.80
4.65
2.80
3.00
4.90
3.00
0.65
0.60
0.95
0.25
Table 5: MiniSO8 mechanical data
Dimensions
Millimeters
Typ. Min.
0.85
Max.
1.1
0.15
0.95
0.40
0.23
3.20
5.15
3.10
0
0.030
0.009
0.003
0.11
0.183
0.11
0.80 0.016
8°
0.10
0°
Inches
Typ.
0.033
0.118
0.193
0.118
0.026
0.024
0.037
0.010
Max.
0.043
0.006
0.037
0.016
0.009
0.126
0.203
0.122
0.031
8°
0.004
DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
7.3 DFN8 2x2 package information
Figure 30: DFN8 2x2 package outline
Package information
D
D2
E
E2 e
L ddd
A
A1
A3 b
Ref.
Min.
0.51
0.18
1.85
1.45
1.85
0.75
Table 6: DFN8 2x2 mechanical data
Dimensions
Millimeters
Typ.
0.55
Max.
0.60
Min.
0.020
0.05
0.15
0.25 0.30 0.007
2.00
1.60
2.00
0.90
0.50
0.3
2.15
1.70
2.15
1.00
0.425
0.08
0.073
0.057
0.073
0.030
Inches
Typ.
0.022
0.006
0.010
0.079
0.063
0.079
0.035
0.020
0.012
Max.
0.024
0.002
0.012
0.085
0.067
0.085
0.039
0.017
0.003
DocID2163 Rev 15 19/25
Package information LM158, LM258, LM358, LM158A, LM258A,
LM358A
Figure 31: DFN8 2x2 recommended footprint
20/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
7.4 TSSOP8 package information
Figure 32: TSSOP8 package outline
Package information
Ref.
D
E
E1 e k
L
L1 aaa
A
A1
A2 b c
Min.
0°
0.45
0.05
0.80
0.19
0.09
2.90
6.20
4.30
Table 7: TSSOP8 mechanical data
Dimensions
Millimeters
Typ. Min.
1.00
3.00
6.40
4.40
0.65
Max.
1.2
0.15
1.05
0.30
0.20
3.10
6.60
4.50
0.002
0.031
0.007
0.004
0.114
0.244
0.169
0.60
1
0.1
8°
0.75
0°
0.018
Inches
Typ.
0.039
0.118
0.252
0.173
0.0256
0.024
0.039
0.004
Max.
0.047
0.006
0.041
0.012
0.008
0.122
0.260
0.177
8°
0.030
DocID2163 Rev 15 21/25
Ordering information LM158, LM258, LM358, LM158A, LM258A,
LM358A
8 Ordering information
Order code Temperature range
Table 8: Order codes
Package
LM158QT
LM158DT
LM258ADT
LM258DT
LM258APT
LM258AST
LM258QT
LM358DT
LM358ADT
LM358PT
LM358APT
LM358ST
LM358AST
LM358QT
-55 °C to 125 °C
-40 °C to 105 °C
0 °C to 70 °C
DFN8 2x2
SO8
SO8
SO8, automotive grade
SO8
TSSOP8
MiniSO8
DFN8 2x2
SO8
SO8, automotive grade
SO8
TSSOP8
MiniSO8
DFN8 2x2
Packaging
Tape and reel
Marking
K4A
158
258A
258AY
258
258A
K408
K4C
358
358Y
358A
358
358A
K405
K404
K4E
Notes:
(1)
Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q
002 or equivalent.
22/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
9
Revision history
Revision history
Date Revision
Table 9: Document revision history
Changes
01-Jul- 2003
02-Jan-2005
01-Jul-2005
05-Oct-2006
30-Nov-2006
25-Apr-2007
12-Feb-2008
26-Aug-2008
02-Sep-2011
1
2
3
4
5
6
7
8
9
First release.
R thja
and T j
parameters added in AMR Table 1: "Absolute maximum ratings".
ESD protection inserted in Table 1: "Absolute maximum ratings".
Added Figure 17: Phase margin vs. capacitive load.
Added missing ordering information.
Removed LM158A, LM258A and LM358A from document title.
Corrected error in MiniSO-8 package data. L1 is 0.004 inch.
Added automotive grade order codes in Section 7: "Ordering information".
Corrected V
CC
max (30 V instead of 32 V) in operating conditions.
Changed presentation of electrical characteristics table.
Deleted V opp
parameter in electrical characteristics table.
Corrected miniSO-8 package information.
Corrected temperature range for automotive grade order codes.
Updated automotive grade footnotes in order codes table.
Added limitations on input current in Table 1: "Absolute maximum ratings".
Corrected title for Figure 11.
Added E and L1 parameters in Table 4: "SO8 package mechanical data".
Changed Figure 31: "TSSOP8 package mechanical drawing".
In Section 6: "Package information", added:
DFN8 2 x 2 mm package mechanical drawing
DFN8 2 x 2 mm recommended footprint
DFN8 2 x 2 mm order codes.
06-Apr-2012
11-Jun-2013
10
11
Removed order codes LM158YD, LM258AYD, LM258YD and
LM358YD from Table 8: "Order codes".
Table 8: "Order codes": removed order codes LM158D,
LM158YDT, LM258YDT, and LM258AD; added automotive grade qualification to order codes LM258ATDT and LM358YDT; updated marking for order codes LM158DT and LM258D/LM258DT; updated temperature range, packages, and packaging for several order codes.
DocID2163 Rev 15 23/25
Revision history
Date
20-Jun-2014
13-Nov-2015
24-Aug-2016
22-Nov-2017
Revision
12
13
14
15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
Changes
Removed DIP8 package
Corrected typos (W replaced with Ω, £ replaced with ≤)
Updated Features
Added Related products
Table 3: replaced DV io with ΔV io
/ΔT and DI io with ΔI io
/ΔT.
Updated Table 7 for exposed pad dimensions
Table 8: "Order codes": removed order codes LM258YPT and
LM258AYPT; removed all order codes for devices with tube packing; added package code (NB) to DFN8 2x2 package.
Updated document layout
Updated name of the "DFN8 2x2 (NB) mm" package to "DFN8
2x2" everywhere in datasheet.
Section 2: "Package pin connections": placed the package's pinout in this section and added note about exposed pad.
Table 8: "Order codes": removed order codes LM258ST,
LM358YPT, and LM358AYPT.
Table 6: "DFN8 2x2 mechanical data" : added typ. value for "L" dimension.
Updated: related products on the cover page.
Updated: Section 3: "Absolute maximum ratings" ,
Section 4: "Electrical characteristics" ,
Figure 6: "Voltage follower pulse response with VCC = 30 V" and
24/25 DocID2163 Rev 15
LM158, LM258, LM358, LM158A, LM258A,
LM358A
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2017 STMicroelectronics – All rights reserved
DocID2163 Rev 15 25/25
Letöltés
A nyilvános link frissítve
A csevegés nyilvános linkje frissítve lett. You may view and manage your chat links after registration here.
Dokumentum nyilvános linkje
Hirdetés