Advertisement
Advertisement
ALTAIR05T-800
Off-line all-primary sensing switching regulator
Datasheet - production data
Output cable drop compensation
SO16N package
Applications
Features
AC-DC chargers for mobile phones and other hand-held equipments
Compact SMPS that requires a precise
Constant voltage and constant current output regulation (CV/CC) with no current and/or voltage regulation optocoupler
Tight regulation also during heavy load
Description transients
800 V avalanche rugged internal power
The ALTAIR05T-800 is a high-voltage all-primary sensing switcher intended to operate directly section
Quasi-resonant (QR) operation
Low standby power consumption
Automatic self-supply
Input-voltage feedforward for mainsindependent CC regulation from the rectified mains with minimum external parts. It combines a low voltage, high performance PWM controller chip and an 800 V avalanche rugged power section in the same package.
Figure 1: Block diagram
October 2016 DocID17957 Rev 2
This is information on a product in full production.
1/27 www.st.com
Contents ALTAIR05T-800
Contents
1 Device description ........................................................................... 3
2 Pin connection ................................................................................. 4
3 Maximum ratings ............................................................................. 6
Absolute maximum ratings ................................................................ 6
Thermal data ..................................................................................... 6
4 Electrical characteristics ................................................................ 7
5 Application information ................................................................ 11
Power section and gate driver ......................................................... 12
High-voltage start-up generator ....................................................... 12
Zero-current detection and triggering block ..................................... 13
Constant voltage operation ............................................................. 15
Constant-current operation ............................................................. 15
Voltage feedforward block ............................................................... 17
Cable drop compensation (CDC) .................................................... 18
Burst-mode operation at no-load or very light load .......................... 19
Soft-start and starter block .............................................................. 19
Hiccup mode OCP .......................................................................... 20
Layout recommendations ................................................................ 21
6 Typical application ........................................................................ 22
7 Package information ..................................................................... 23
SO16N package information ........................................................... 23
9 Revision history ............................................................................ 26
2/27 DocID17957 Rev 2
ALTAIR05T-800
1 Device description
Device description
The device combines a low voltage PWM controller and an 800 V avalanche rugged power section in the same package.
The current-mode controller chip is specifically designed for off-line quasi-resonant flyback converters.
The device provides a constant output voltage (CV) and constant output current (CC) regulation using the primary sensing feedback. In this manner, the optocoupler, the secondary voltage reference, and the current sensor are no more necessary, even though an accurate regulation also during heavy load transients is maintained. Furthermore, the voltage drop can be compensated on the output cable so to improve CV regulation on the external accessible terminals.
Quasi-resonant operation is guaranteed by a transformer demagnetization sensing input that turns on the power section. The same input also serves to monitor the output voltage, to perform CV regulation, and to achieve mains-independent CC regulation (line voltage feedforward).
The maximum switching frequency is limited to 166 kHz, so that at medium-light load a special function automatically lowers the operating frequency still maintaining the valley switching operation. At very light load, the device enters a controlled burst-mode operation that, along with the built-in high-voltage start-up circuit and the low operating current, helps to minimize the standby power.
Although an auxiliary winding is required in the transformer to correctly perform CV/CC regulation, the chip is able to power itself directly from the rectified mains. This is useful especially during CC regulation, where the flyback voltage generated by the winding drops below UVLO threshold. However, if ultra-low no-load input consumption is required to comply with the most stringent energy-saving recommendations, then the device needs to be powered via the auxiliary winding.
In addition to these functions that optimize the power handling under different operating conditions, the device offers protection features that considerably increase safety and reliability of the end-product: auxiliary winding disconnection - or brownout - detection and shorted secondary rectifier - or saturation of the transformer. All of them are in auto-restart mode.
DocID17957 Rev 2 3/27
Pin connection
2 Pin connection
Figure 2: Pin connection (top view)
ALTAIR05T-800
The copper area for heat dissipation has to be designed under the drain pins
Number Name
1, 2
3
4
5
Table 1: Pin functions
Function
SOURCE
Power section source and input to the PWM comparator. The current flowing to the
MOSFET is sensed through a resistor connected between the pin and GND. The resulting voltage is compared with an internal reference (0.75 V max.) to determine the MOSFET turn-off event. The pin is equipped with 250 ns blanking time after the gate-drive output goes high due to the improved noise immunity. If a second comparison level located at 1 V is exceeded, the IC is stopped and restarted after Vcc has dropped below 5 V.
Vcc
GND
IREF
Supply voltage of the device. An electrolytic capacitor, connected between this pin and ground, is initially charged by the internal high-voltage start-up generator; when the device runs, the same generator keeps it charged in case the voltage supplied by the auxiliary winding is not sufficient. This feature is disabled in case a protection is tripped. Sometimes a small bypass capacitor (0.1 µF typ.) to GND might be useful to get a clean bias voltage for the signal part of the IC.
Ground. Current return for the signal part of the IC and the gate drive. All of ground connections of the bias components should be tied to a trace going to this pin and kept separate from any pulsed current return.
CC regulation loop reference voltage. An external capacitor has to be connected between this pin and GND. An internal circuit develops a voltage on this capacitor that is used as the reference for the MOSFET peak drain current during CC regulation. The voltage is automatically adjusted to keep the average output current constant.
4/27 DocID17957 Rev 2
ALTAIR05T-800
Number Name
6
7
8
9 to 11
12
ZCD/FB
COMP
CDC
N.A.
N.C.
13 to 16 DRAIN
Pin connection
Function
Demagnetization sensing of the transformer for quasi-resonant operation. Input/output voltage monitor. A negative-going edge triggers the MOSFET turn-on event. The current sourced by the pin during ON-time is monitored to get an image of the input voltage to the converter, in order to compensate the internal delay of the current sensing circuit and achieve a CC regulation independent of the mains voltage. If this current does not exceed
50 µA, either a floating pin or an abnormal low input voltage is assumed, the device is stopped and restarted after Vcc has dropped below 5 V. Besides, the pin voltage is sampled and held right at the end of the demagnetization of the transformer to get an accurate image of the output voltage to be fed to the inverting input of the internal, transconductance-type, error amplifier, whose non-inverting input is referenced to 2.5 V. Please note that the maximum I
ZCD/FB
sunk/sourced current does not have to exceed ±2 mA (AMR) in all V
IN range conditions (85-265 VAC). No capacitor is allowed between the pin and the auxiliary transformer.
Output of the internal transconductance error amplifier. The compensation network is placed between this pin and GND to achieve stability and good dynamic performance of the voltage control loop.
Cable drop compensation input. During CV regulation this pin, which can sink current, provides a voltage lower than the internal reference voltage (2.5 V) by an amount proportional to the DC load current. By connecting a resistor between this pin and ZCD/FB, the CV regulation setpoint is increased proportionally. This allows that the voltage drop across the output cable to be compensated and, ideally, that zero-load regulation on the externally available terminals to be achieved. Leave the pin open if the function is not used.
Not available. These pins must be left not connected.
Not internally connected. Provision for clearance on the PCB to meet safety requirements.
Drain connection of the internal power section. The internal high-voltage start-up generator sinks current from this pin as well. Pins connected to the internal metal frame to facilitate heat dissipation.
DocID17957 Rev 2 5/27
Maximum ratings
3
3.1
3.2
Maximum ratings
ALTAIR05T-800
Absolute maximum ratings
Symbol Pin
Table 2: Absolute maximum ratings
Parameter
V
DS
I
D
Eav
Vcc
I
ZCD/FB
---
I
CDC
Ptot
Tj
Tstg
1,2, 13-16 Drain-to-source (ground) voltage
1,2, 13-16 Drain current
1,2, 13-16 Single pulse avalanche energy (Tj = 25 °C, I
D
= 1 A)
3 Supply voltage (Icc < 25 mA)
6 Zero-current detector current
7, 8
8
Analog inputs and outputs
Maximum sunk current
Power dissipation @ T
A
= 50 °C
Junction temperature range
Storage temperature
Thermal data
Symbol
R th j-pin
R th j-amb
Table 3: Thermal data
Parameter
Thermal resistance, junction-to-pin
Thermal resistance, junction-to-ambient
Max. value
10
110
Value Unit
-1 to 800
1
V
A
50 mJ
Self-limiting V
±2 mA
-0.3 to 3.6
200
0.9
-40 to 150
-55 to 150
V
µA
W
°C
°C
Unit
°C/W
6/27 DocID17957 Rev 2
ALTAIR05T-800 Electrical characteristics
4 Electrical characteristics
(T
J
= -40 to 125 °C, Vcc = 14 V; unless otherwise specified)
Parameter
Table 4: Electrical characteristics
Test conditions Symbol
Power section
V
(BR)DSS
Drain-source breakdown
I
DSS
R
DS(on)
Off-state drain current
Drain-source ON-state resistance
I
D
< 100 µA; T j
= 25 °C
V
DS
= 750 V; T j
= 125 °C
(see Figure 4: "Off-state drain and source current test circuit" and note)
Id = 100 mA; Tj = 25 °C
Id = 100 mA; Tj = 125 °C
(see Figure 3: "COSS output capacitance variation" )
C oss
Effective (energy-related) output capacitance
High-voltage start-up generator
V
Start
Min. drain start voltage
I charge
Vcc startup charge current
I charge
< 100 µA
V
DRAIN
> V
Start
; V
CC
< V
CCOn
Tj = 25 °C
V
CCrestart
Vcc restart voltage
(Vcc falling)
After protection tripping
Supply voltage
Vcc Operating range
Vcc
On
Turn-on threshold
Vcc
Off
Turn-off threshold
V
Z
Zener voltage
Supply current
After turn-on
Icc = 20 mA
Icc start-up
Start-up current
Iq
Icc
Quiescent current
Operating supply current @
50 kHz
Iq
(fault)
Fault quiescent current
(see Figure 5: "Start-up current test circuit" )
(see Figure 6: "Quiescent current test circuit" )
(see Figure 7: "Operating supply current test circuit" )
During hiccup and brownout (see Figure
8: "Quiescent current during fault test circuit" )
Start-up timer
T
START
Start timer period
T
RESTART
Restart timer period during burst mode
Zero-current detector
I
ZCDb
Input bias current
V
ZCDH
Upper clamp voltage
V
ZCDL
Lower clamp voltage
V
ZCD
= 0.1 to 3 V
I
ZCD
= 1 mA
I
ZCD
= - 1 mA
Min. Typ. Max. Unit
800
11
22
80
14
28
40
4
50
5.5
60
7
9.5 10.5 11.5
5
11.5
12
9
23
13
10
25
1
1.4
23
14
11
27
V
µA
Ω
V mA
V
V
V
V
V
200 300 µA
1.4 mA
1.7 mA
250 350 µA
100 125 175 µs
400 500 700 µs
3.0
0.1
3.3
1
3.6
µA
V
-90 -60 -30 mV
DocID17957 Rev 2 7/27
Electrical characteristics
Symbol Parameter
I
V
ZCDA
Arming voltage
V
ZCDT
Triggering voltage
ZCDON
Min. source current during
MOSFET ON-time
T
BLANK
Trigger blanking time after
MOSFET turn-off
Line feedforward
R
FF
Equivalent feedforward resistor
Transconductance error amplifier
Test conditions
Positive-going edge
Negative-going edge
V
COMP
≥ 1.3 V
V
COMP
= 0.9 V
I
ZCD
= 1mA
V
REF
Voltage reference gm
Gv
GB
Transconductance
Voltage gain
Gain-bandwidth product
I
COMP
Source current
Sink current
V
COMPH
Upper COMP voltage
V
COMPL
Lower COMP voltage
V
COMPBM
Burst-mode threshold
Hys Burst-mode hysteresis
CDC function
V
CDC
CDC voltage reference
Current reference
V
IREFx
Maximum value
V
CREF
Current reference voltage
Current sense t
LEB
Leading-edge blanking t d(H-L)
Delay-to-output
V
CSx
Max. clamp value
V
CSdis
Hiccup-mode OCP level
Notes:
(1)
Parameters tracking each other.
Tj = -40 to 125°C and
∆I
COMP
= ±10 µA V
COMP
= 1.65 V
Open loop
V
ZCD
= 2.3 V, V
COMP
= 1.65 V
V
ZCD
= 2.7 V, V
COMP
= 1.65 V
V
ZCD
= 2.3 V
V
ZCD
= 2.7 V
V
COMP
= 1.1 V, I
CDC
V
COMP
= V
dV cs
/d t
ALTAIR05T-800
Min. Typ. Max. Unit
100 110 120 mV
50 60 70 mV
µA -25 -50 -75
6
30
µs
45 Ω
2.46 2.5 2.54
V
2.42
1.3 2.2
73
500
70 100
400 750
2.7
0.7
1
65
2.58
3.2 mS dB
KHz
µA
µA
V
V
V mV
2.4 2.5 2.6 V
1.5 1.6 1.7 V
0.192 0.2 0.208 V
200 250 300 ns
300
0.7 0.75 0.8 ns
V
0.92 1 1.08 V
8/27 DocID17957 Rev 2
ALTAIR05T-800 Electrical characteristics
Figure 3: COSS output capacitance variation
Figure 4: Off-state drain and source current test circuit
The measured I
DSS
is the sum between the current across the start-up resistor and the off-state drain current of the MOSFET.
Figure 5: Start-up current test circuit
DocID17957 Rev 2 9/27
Electrical characteristics
Figure 6: Quiescent current test circuit
ALTAIR05T-800
Figure 7: Operating supply current test circuit
10/27
The circuit across the ZCD pin is used for switch-on synchronization.
Figure 8: Quiescent current during fault test circuit
DocID17957 Rev 2
ALTAIR05T-800
5 Application information
Application information
The device is an off-line all-primary sensing switching regulator, based on quasi-resonant flyback topology.
Depending on the load condition of the converter, the device is able to work in different
modes (see Figure 9: "ALTAIR05T-800 multi-mode operation " ):
1. QR mode at heavy load. Quasi-resonant operation lies in synchronization of the turnon of the MOSFET to the transformer demagnetization by detecting the resulting negative-going edge of the voltage across any winding of the transformer. Therefore the system works close to the boundary between discontinuous (DCM) and continuous conduction (CCM) of the transformer. As a result, the switching frequency is different for different line/load conditions (see the hyperbolic-like portion of the
curves in Figure 9: "ALTAIR05T-800 multi-mode operation " ). Minimum turn-on losses,
low EMI emission and safe behavior in short-circuit are the main benefits of this kind of operation.
2. Valley-skipping mode at medium/ light load. Depending on voltage on COMP pin, the device defines the maximum operating frequency of the converter. As the load is reduced, the MOSFET turn-on event does not occur on the first valley but on the second one, the third one and so on. In this manner the switching frequency does not
increase any longer (piecewise linear portion in Figure 9: "ALTAIR05T-800 multi-mode operation " ).
3. Burst-mode with no or very light load. When the load is extremely light or disconnected, the converter enters a controlled on/off operation with constant peak current. Decreasing the load result in frequency reduction, which can go down even to few hundred hertz, thus minimizing all frequency-related losses and complying with energy saving regulations or recommendations. Being the peak current very low, no issue of audible noise arises.
Figure 9: ALTAIR05T-800 multi-mode operation
DocID17957 Rev 2 11/27
Application information
5.1 Power section and gate driver
ALTAIR05T-800
The power section guarantees safe avalanche operation within the specified energy ratings as well as high dv/dt capability. The power MOSFET has a V
(BR)DSS
of 800 V min. and a typical R
DS(on) of 11 Ω.
The gate driver is designed to supply a controlled gate current during both turn-on and turnoff in order to minimize common mode EMI. Under UVLO conditions an internal pull-down circuit holds the gate low in order to ensure that the power MOSFET cannot be turned on accidentally.
5.2 High-voltage start-up generator
The HV current generator is supplied through the DRAIN pin and it is enabled only if the input bulk capacitor voltage is higher than V start
threshold, 50 V
DC
typically. When the HV current generator is ON, the I charge
current (5.5 mA typical value) is delivered to the capacitor on the V
CC
pin.
bulk capacitor is high enough, the HV generator is sufficiently biased to start operating, thus it draws about 5.5 mA (typical) from the bulk capacitor. Most of this current charges the bypass capacitor connected between the Vcc pin and ground and makes its voltage rise linearly.
As the Vcc voltage reaches the start-up threshold (13 V typ.) the chip starts operating, the internal power MOSFET is enabled to switch and the HV generator is cut off. The IC is powered by the energy stored in the V cc
capacitor.
The chip is able to power itself directly from the rectified mains: when the voltage on the
V
CC
pin falls below Vcc restart
(10.5 V typ.), during each MOSFET off-time event, the HV current generator is turned on and charges the supply capacitor until it reaches the V
CCOn threshold.
In this way, the self-supply circuit develops a voltage high enough to sustain the operation of the device. This feature is useful especially during CC regulation, when the flyback voltage generated by the auxiliary winding alone may not be able to keep Vcc above
V
CCrestart
.
At converter power-down the system loses regulation as soon as the input voltage falls below V
Start
. This prevents restart attempts of the converter and ensures monotonic output voltage decay at system power-down.
12/27 DocID17957 Rev 2
ALTAIR05T-800 Application information
Figure 10: Timing diagram: normal power-up and power-down sequences
5.3 Zero-current detection and triggering block
The zero-current detection (ZCD) and triggering blocks switch on the power MOSFET if a negative-going edge falling below 50 mV is applied to the ZCD/FB pin. To do so, the triggering block must be previously armed by a positive-going edge exceeding 100 mV.
This feature is used to detect the transformer demagnetization for QR operation, where the signal for the ZCD input is obtained from the auxiliary winding of the transformer also used to supply the IC.
Figure 11: ZCD block, triggering block
The triggering block is blanked after the MOSFET turn-off to prevent any negative-going edge that follows leakage inductance demagnetization from triggering the ZCD circuit erroneously.
This blanking time is dependent on the voltage on COMP pin: it is T
BLANK
= 30 µs for V
COMP
= 0.9 V, and decreases almost linearly down to T
BLANK
= 6 µs for V
COMP
= 1.3 V.
DocID17957 Rev 2 13/27
Application information ALTAIR05T-800
The voltage on the pin is both top and bottom limited by a double clamp, as illustrated in
the internal diagram of the ZCD block, see Figure 11: "ZCD block, triggering block" . The
upper clamp is typically at 3.3 V, while the lower clamp is at -60 mV. The interface between the pin and the auxiliary winding is a resistor divider. Its resistance ratio as well as the individual resis
tance values have to be properly chosen (see “ Section 5.4: "Constant voltage operation"
” and “ Section 5.6: "Voltage feedforward block" ”).
Please note that the maximum I
ZCD/FB
sunk/sourced current does not have to exceed ±2 mA
(AMR) in all V
IN
range conditions (85-265 VAC). No capacitor is allowed between ZCD pin and the auxiliary transformer.
The switching frequency is limited to 166 kHz, as the operating frequency of the converter tends to increase excessively at light load and high input voltage.
A starter block is also used to start up the system, that is, to turn on the MOSFET during the converter power-up, when no or a too small signal is available on the ZCD pin.
The starter frequency is 2 kHz if COMP pin is below burst mode threshold, i.e. 1 V, while it becomes 8 kHz if this voltage exceeds this value.
After the first few cycles initiated by the starter, as the voltage developed across the auxiliary winding becomes so high to arm the ZCD circuit, the turn-on of the MOSFET starts to be locked to demagnetization of the transformer, hence QR operation is set.
The starter is also active when the IC is in CC regulation and the output voltage is not so high to allow the ZCD triggering.
If the demagnetization completes, hence a negative-going edge appears on the ZCD pin, after a time exceeding time T
BLANK
from the previous turn-on, the MOSFET is turned on again, with some delay to ensure minimum voltage at turn-on. If, instead, the negativegoing edge appears before T
BLANK
has elapsed, it is ignored and only the first negativegoing edge after T
BLANK
turns on the MOSFET. In this way one or more drain ringing cycles
BLANK
.
Figure 12: Drain ringing cycle skipping as the load is progressively reduced
14/27
Note that when the system operates in valley skipping-mode, uneven switching cycles may be observed under some line/load conditions, due to the fact that the OFF-time of the
MOSFET changes with discrete steps of one ringing cycle, while the OFF-time needed for cycle-by-cycle energy balance may fall in between. Thus one or some longer switching cycles are compensated by one or some shorter cycles and vice versa. However, this mechanism is absolutely normal and there is no appreciable effect on the performance of the converter or on its output voltage.
DocID17957 Rev 2
ALTAIR05T-800
5.4 Constant voltage operation
Application information
The IC is specifically designed to work in primary regulation and the output voltage is sensed through a voltage partition of the auxiliary winding, just before the auxiliary rectifier diode.
Figure 13: "Voltage control principle: internal schematic" shows the internal schematic of
the constant voltage mode and the external connections.
Figure 13: Voltage control principle: internal schematic
Due to the parasitic wire resistance, the auxiliary voltage is representative of the output just when the secondary current becomes zero. For this purpose, the signal on ZCD/FB pin is sampled and held at the end of transformer demagnetization to get an accurate image of the output voltage and it is compared with the error amplifier internal reference.
The COMP pin is used for the frequency compensation: usually, an RC network, which stabilizes the overall voltage control loop, is connected between this pin and ground.
The output voltage can be defined according to the following formula:
Equation 1
5.5
Where N
SEC
and N
AUX
are the numbers of secondary and auxiliary turns respectively.
The R
ZCD
value can be defined depending on the application parameters (see Section 5.6:
"Voltage feedforward block" ).
Constant-current operation
Figure 14: "Current control principle" presents the principle used to control the average
output current of the flyback converter.
The output voltage of the auxiliary winding is used by the demagnetization block to generate the control signal for the MOSFET switch Q1. R resistor in series absorbs a current V
C
/R, where V
C
is the voltage developed across the capacitor C
REF
.
The flip-flop output is high as long as the transformer delivers current to secondary-side.
This is shown in Figure 15: "Constant current operation: switching cycle waveforms" .
The capacitor C
REF
has to be chosen so that its voltage V
C
can be considered as a constant. Since it is charged and discharged by current in the range of some tens of µA
DocID17957 Rev 2 15/27
Application information ALTAIR05T-800
(I
CREF
is typically 20 µA) at the switching frequency rate, a capacitance value in the range
4.7 to10 nF is suitable for switching frequencies of 10 kHz.
The average output current can be expressed as follows:
Equation 2
Where N
PRI
is the number of the primary turns.
This formula shows that the average output current does not depend neither on the input or the output voltage, nor on transformer inductance values. The external parameters defining the output current are the transformer ratio n and the sense resistor R
SENSE
.
Figure 14: Current control principle
Figure 15: Constant current operation: switching cycle waveforms
16/27 DocID17957 Rev 2
ALTAIR05T-800
5.6 Voltage feedforward block
Application information
The current control structure uses the voltage V
C
to define the output current, according to
Equation 2 . Actually, the CC comparator is affected by an internal propagation delay T d
, which switches off the MOSFET with a peak current higher than the foreseen value.
This current overshoot is equal to:
Equation 3
Where L
P
is the primary inductance.
It introduces an error on the calculated CC setpoint, depending on the input voltage.
The device implements a line feedforward function, which solves the issue by introducing an input voltage dependent offset on the current sense signal, in order to adjust the cycleby-cycle current limitation.
The internal schematic is shown in Figure 16: "Feedforward compensation: internal schematic" .
Figure 16: Feedforward compensation: internal schematic
The R
ZCD
resistor can be calculated as follows:
Equation 4
In this case the peak drain current does not depend on input voltage anymore.
Concerning the R
ZCD
value: during ON-time of the MOSFET, the current sourced by the
ZCD/FB pin, I
ZCD
, is compared with an internal reference current I
ZCDON
(-50 µA typical).
If I
ZCD
< I
ZCDON
, the brownout function is active and the IC is shut down.
This feature is especially important when the auxiliary winding is accidentally disconnected and considerably increases safety and reliability of the end-product.
DocID17957 Rev 2 17/27
Application information
5.7 Cable drop compensation (CDC)
ALTAIR05T-800
The voltage control loop regulates the output voltage as seen across the output capacitor.
If an output cable is used to supply the load, the voltage on the externally available terminals is dependent of the output current value. The CDC function compensates the voltage drop across the cable, so ideally zero-load regulation can be also achieved at the end of the cable.
Figure 17: "CDC block: internal schematic" presents the internal schematic.
Figure 17: CDC block: internal schematic
18/27
During CV regulation, as the CDC block is able to sink current, a resistor connected between its output and ZCD/FB pin allows the CV setpoint to be increased, by providing a voltage lower than the internal reference voltage by an amount proportional to the average load current.
If R
CABLE
is the total cable resistance, the resistor value can be calculated by using the following equation:
Equation 5
In this equation R
CABLE
is the total resistance of the output cable.
The CDC block acts as an outer control loop with a positive feedback that changes the CV setpoint, by affecting the stability of the overall system. In order to avoid this type of issue, the CV setpoint response time must be much lower than that of the inner voltage loop.
For this purpose the CDC block is designed with a time response of a few tens of ms. For the same reason, the minimum voltage on CDC pin is bottom limited to 2.25 V.
If the function is not required, the pin can be connected to ground or left open.
DocID17957 Rev 2
ALTAIR05T-800
5.8
Application information
Burst-mode operation at no-load or very light load
When the voltage on the COMP pin falls 65 mV below a threshold fixed internally at a value, V
COMPBM
, the IC is disabled with the MOSFET kept in OFF-state and its consumption reduced at a lower value to minimize V cc
capacitor discharge.
In this condition the converter operates in burst-mode (one pulse train every T
START
= 500
µs), with minimum energy transfer.
As a result of the energy delivery stop, the output voltage decreases: after 500 µs the controller switches on the MOSFET again and the sampled voltage on the ZCD pin is compared with the internal reference. If the voltage on the EA output, as a result of the comparison, exceeds the V
COMPL
threshold, the device restarts switching, otherwise it stays
OFF for another 500 µs period.
In this way the converter works in burst-mode with a nearly constant peak current defined by the internal disable level. Then a load decrease causes a frequency reduction, which can go down even few hundred hertz, thus minimizing all frequency-related losses and complying with energy saving regulations. This kind of operation, shown in the timing
diagrams of Figure 18: "Load-dependent operating modes: timing diagrams" , along with the
others previously described, is noise-free since the peak current is low.
Figure 18: Load-dependent operating modes: timing diagrams
5.9 Soft-start and starter block
The soft-start feature is automatically implemented by the constant current block, as the primary peak current is limited from the voltage on the C
REF
capacitor.
During start-up, as the output voltage is zero, the IC starts in CC mode with no high peak current operations. In this way the voltage on the output capacitor increases slowly and the soft-start feature is ensured.
Actually the C
REF
value is not important to define the soft-start time, as its duration depends on other circuit parameters, such as transformer ratio, sense resistor, output capacitors and load. The user can define the best appropriate value.
DocID17957 Rev 2 19/27
Application information
5.10 Hiccup mode OCP
ALTAIR05T-800
The device is also protected against short-circuit of the secondary rectifier, short-circuit on the secondary winding or a hard-saturated flyback transformer. A comparator monitors continuously the voltage on the R
SENSE
and activates a protection circuitry if this voltage exceeds 1 V.
To distinguish an actual malfunction from a disturbance (e.g. induced during ESD tests), the first time the comparator is tripped the protection circuit enters a “warning state”. If in the subsequent switching cycle the comparator is not tripped, a temporary disturbance is assumed and the protection logic is reset in its idle state; if the comparator is tripped again a real malfunction is assumed and the device is stopped.
This condition is latched as long as the device is supplied. While it is disabled, however, no energy comes from the self-supply circuit; hence the voltage on the V
CC
capacitor decays and crosses the UVLO threshold after some time, which clears the latch. The internal startup generator is still off, then the V
CC
voltage still needs to go below its restart voltage before the V
CC
capacitor is charged again and the device restarted. Ultimately, this results in a low-frequency intermittent operation (hiccup mode operation), with very low stress on
the power circuit. This special condition is illustrated in the timing diagram of Figure 19:
"Hiccup mode OCP: timing diagram" .
Figure 19: Hiccup mode OCP: timing diagram
20/27 DocID17957 Rev 2
ALTAIR05T-800
5.11 Layout recommendations
Application information
A proper printed circuit board layout is essential for the correct operation of any switchmode converter and this is true for the ALTAIR05T-800 as well. Placing components carefully, routing traces correctly, tracing widths appropriately and compliance with isolation distances are the major issues. In particular:
The compensation network should be connected as close as possible to the COMP pin, maintaining the trace for the GND as short as possible
Signal ground should be routed separately from power ground and from the sense resistor trace.
Figure 20: Suggested routing for converter
DocID17957 Rev 2 21/27
Typical application
6 Typical application
ALTAIR05T-800
Figure 21: Test board schematic: 5 W wide range mains CC/CV battery charger
22/27
Load [%]
25
50
75
100
Load [%]
25
50
75
100
I
OUT
[A]
0.25
0.5
0.75
1
Table 5: Efficiency at 115 VAC
V
OUT
[V]
4.97
4.97
4.97
4.98
Average efficiency
P
OUT
[W]
1.243
2.485
3.728
4.980
P
IN
[W]
1.643
3.156
4.72
6.4
I
OUT
[A]
0.25
0.5
0.75
1
Table 6: Efficiency at 230 VAC
V
OUT
[V]
4.98
4.97
4.98
4.99
Average efficiency
P
OUT
[W]
1.245
2.485
3.735
4.990
P
IN
[W]
1.88
3.349
4.838
6.326
Efficiency [%]
75.62
78.64
78.97
77.81
77.79
Efficiency [%]
66.22
74.18
77.22
78.88
74.12
DocID17957 Rev 2
ALTAIR05T-800
7
7.1
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com
.
ECOPACK ® is an ST trademark.
SO16N package information
Figure 22: SO16N package outline
DocID17957 Rev 2 23/27
Package information
Dim. e h
L k ccc c
D
E
E1
A
A1
A2 b
0.25
0.4
0
0.1
1.25
0.31
0.17
9.8
5.8
3.8
Table 7: SO16N mechanical data mm
Min. Typ.
9.9
6
3.9
1.27
ALTAIR05T-800
Max.
1.75
0.25
0.51
0.25
10
6.2
4
0.5
1.27
8
0.1
24/27 DocID17957 Rev 2
ALTAIR05T-800
8 Order code
Order code
ALTAIR05T-800
ALTAIR05T-800TR
Table 8: Ordering information
Package
SO16N
Order code
Packing
Tube
Tape and reel
DocID17957 Rev 2 25/27
Revision history
9
ALTAIR05T-800
Revision history
Date Revision
Table 9: Document revision history
Changes
25-Oct-2010
20-Oct-2016
1
2
Initial release.
Updated Table 2: "Absolute maximum ratings" ,
Section 4: "Electrical characteristics"
and Section 7: "Package information" .
Minor text changes.
26/27 DocID17957 Rev 2
ALTAIR05T-800
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics
– All rights reserved
DocID17957 Rev 2 27/27
Advertisement