advertisement
![Versaclean VersaCarpet VC700 Owner's Manual | Manualzz Versaclean VersaCarpet VC700 Owner's Manual | Manualzz](http://s1.manualzz.com/store/data/006441575_1-1347cbb8b8078602642c34b7b1c5882b-360x466.png)
Owner’s Manual
VersaCarpet™ VC700 Carpet and Upholstery Cleaner
LEGEND BRANDS, INC.
15180 Josh Wilson Road
■
Burlington, WA 98233
800-932-3030
■
http://VersaCleanSystems.com
Patents: http://www.LBpatents.com
R E A D A N D S A V E T H E S E I N S T R U C T I O N S
WARNING
Read and understand manual before operating.
W ARNING! Do not alter or modify your VersaCarpet in any way. Use only replacement parts authorized by Legend Brands. Modifications or use of unapproved parts could create a hazard and will void your warranty. Contact your local authorized distributor for assistance.
WARNING! Electric shock hazard, rotating head, hot surface hazards. Unplug unit before opening cover for cleaning or servicing.
WARNING! Unit must be grounded.
• Keep motor and wiring dry. Keep out of standing water and do not use in area likely to be subject to water intrusion. Do not expose to rain, water or snow.
• Insert three-prong plugs on power cords into a GFCI outlet. Do not use adapter. Never cut off third prongs.
FIRE HAZARD
• Keep away from open flames and heat sources.
• Do not use or store where vapors from gasoline, solvents, thinners or other flammable materials may be present.
WARNING! Unplug unit before cleaning or servicing.
• Turn off unit and unplug before lifting.
• Handle the unit carefully. Always operate the unit on a stable, level surface. Do not drop, throw, or place where it could fall. Rough treatment can damage the unit, and may create a hazardous condition or void the warranty.
• Inspect the power cords before use. If cord is damaged, do not use. Always grasp the plug (not the cord) to unplug.
• Use only with cords supplied with the unit, or 12 gauge (or larger) cords.
• The unit must be plugged into two 15 amp
115V/60 Hz circuits.
• Do not attempt to repair the unit. For Authorized
Service Centers, call VersaClean Service at 800-
932-3030.
BEFORE YOU BEGIN
Warranty registration
Visit warranty.VersaCleanSystems.com to register your purchase. Registration allows us to better assist you with using, maintaining or servicing your equipment and to contact you in case we have important safety information concerning your product. If you determine service is required, have your equipment model, serial number and original proof of purchase available and call your distributor for assistance with obtaining a return material authorization (RMA).
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 1 Legend Brands, Inc.
CONTROLS AND COMPONENTS
ACCESSORY PORTS
1. High pressure water outlet
2. Vacuum inlet (keep covered when not in use.)
Solution prespray wand. Keep clipped in place when not in use.
Front lift handle.
Rotary head solution sight window.
Prespray and/or upholstery solution sight window
Solution spray wand hose coil.
WARNING: Moving parts.
Keep hands and feet clear.
Waste tank clear window release clamps
Fresh water inlet
Waste water outlet
Hour meter
Vacuum switch
Pumpout switch
Separate circuit indicator
light. Glows green when unit is properly connected to two
15 amp circuits.
Rotary head control lever
Solution control lever
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 2 Legend Brands, Inc.
BEFORE FIRST USE
TOOLS REQUIRED: 3 mm hex drive bit, 10 mm wrench,
1. Install handle
Using drive and wrench, remove two bolts from posts. Insert tubes over posts and line up the holes. With tubes in position, reinsert two bolts supplied into either the upper or lower holes and tighten until they are snug. For operator comfort, handle may be fixed in one of two positions.
After handle is installed, tuck excess cords into top panel.
NOTE: Locate the Accessory/Spare Parts Kit in product packaging. It contains two sets of impellers and gaskets for servicing
pumpout pump. Set aside for future use.
Handle may be installed in high or low position.
2. Flush system lines.
Unit may contain residual antifreeze from the factory. Flush internal lines with fresh water prior to use.
DO NOT drain used antifreeze on the ground or into storm drains. Dispose of antifreeze only in an approved location. Observe local, state, and federal laws when disposing antifreeze.
A. Flush cleaning head solution lines. Set unit up for operation (see “Setup for Cleaning below), except leave cleaning solution intake tubes disconnected and direct pumpout discharge hose into a bucket or suitable drain. Operate unit for a few minutes on a hard, waterproof surface until discharge runs clear.
B. Flush accessory solution line. Set unit up for accessory operation (see “Cleaning with Accessory Tool/Upholstery Tool” below). Place accessory tool end in a bucket of clean water and operate the VC700 until discharge runs clear.
THE VC700 IS NOW READY FOR CONNECTING WATER SUPPLY.
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 3 Legend Brands, Inc.
SETUP FOR CARPET CLEANING
Attach
FAUCET MOUNTING KIT
to water supply and drain
Use supplied faucet adaptor kit as necessary to fit coupler to faucet.
Connect fresh water coupling to faucet.
Use supplied faucet adaptor kit as necessary to fit coupler to faucet.
Connect fresh water coupling to supply hose.
For best cleaning results, use hot water.
Attach waste water hose to waste coupling.
Direct drain tube into drain.
Connect waste water drain hose to waste water outlet.
Connect water supply to fresh water inlet.
Connect power cords
Sockets are located under the bottom of the control panel. Rotate plug lock to secure plugs. Plug each cord into a 15 amp circuit.
Separate Circuit Indicator light
will glow green when unit is properly connected to two 15 amp circuits.
Turn on water supply
and check for leaks.
Fresh water to VC700
Waste water to drain.
Install cleaning solution bottles and insert feed tubes
Place Step 1 Prespray bottle into left pocket and insert Prespray tube. Secure tube with cap.
Step 2/3 Rinse Extract bottle into right pocket and insert Rinse Extract feed tube into bottle. Secure tube with cap.
NOTICE: This equipment is for use with VersaCarpet and
VersaGreen products only. Use with other products will reduce cleaning performance and may damage the equipment and will void the warranty.
Open tank lid, place one defoamer pellet in filter cage. Replace lid and secure with clamps.
Insert feed tubes as shown.
Step 1
Prespray
Step 2/3 Rinse
Extract
THE VC700 IS NOW READY FOR CARPET CLEANING USE.
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 4 Legend Brands, Inc.
CONTROLS
• Prespray wand.
Squeeze lever to release solution. Wand is pressurized by water supply.
• Control rotary head with left hand lever.
Grip handle firmly before squeezing lever.
• Control solution flow with right hand lever.
Release handle to stop flow.
• To manually pump out tank, press and hold pumpout switch to “Manual” position. Re-
lease switch to return to “Auto” mode.
Use manual pumpout if excessive foaming occurs and at the end of the job to ensure tank is empty.
To use unit with hand tool or wand,
first remove cap from the accessory vacuum inlet and insert vacu-
um adapter tube. Now attach tool to accessory vacuum inlet and accessory high pressure water outlet .
CLEANING PROCEDURES
CARPET
NORMAL SOILS
1. Prespray
with VersaCarpet
Step 1. See label for dwell time.
2. Rinse extract
with
VersaCarpet Step 2.
3. Dry
with suitable airmovers to ensure rapid drying.
CARPET
HEAVY SOILS
1. Prespray
with VersaCarpet
Step 1 HD. See label for dwell time.
2. Dry agitate.
Operate VC700 rotary head over carpet with no solu- tion or vacuum applied.
3. Rinse extract
with
VersaCarpet Step 3
4. Dry
with suitable airmovers to ensure rapid drying.
UPHOLSTERY
1. Prespray
with VersaCarpet
Step 1. See label for dwell time.
2. Rinse extract
with
VersaCarpet Step 3 using hand tool attached to VC700.
3. Dry
Place suitable airmovers to ensure rapid drying.
READ CHEMICAL PRODUCT LABELS FOR DETAILED INSTRUCTIONS.
TRANSPORTATION AND STORAGE
NOTICE: Handle the unit carefully. Do not drop, throw, or place the unit where it could fall. Rough treatment can damage this equipment and may create a hazardous condition or void warranty.
• When repositioning unit, tilt unit back to lift vacuum head 1 to 2 in. above floor to protect rotary head,
• Store and transport securely to avoid any damaging impact to internal parts.
• Secure during transport to prevent sliding and possible injury to vehicle occupants.
• Protect from freezing.
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 5 Legend Brands, Inc.
MAINTENANCE
Important: Do not tip unit on its back, or oil may leak.
Before each use
After each use
Monthly
As needed
Inspect the electrical cord for damage. Look for fraying, cuts, etc. Replace the cord if you find any damage. Use replacement part no. 30-099.
Inspect hoses, water lines and seals. Replace as needed.
Inspect vacuum shoes and gasket. Scratches, gouges and snags can be removed with a flat file. Replace shoe and gasket when grooves in shoe are no longer visible.
Flush out tank and rinse basket clean. Disconnect solution feed tubes and remove bottles.
Attach a vacuum hose to the accessory port, place the other end in a bucket of clean water and extract until pumpout hose discharge runs clear. Be sure to orient basket with hole facing the pipe opening when replacing.
Inspect and clean in-tank filters. Remove from tank and rinse clean. Wipe out tank interior with damp cloth and reinstall filters. Be sure to orient bottom tank filter horizontally and ensure that it is firmly in place.
Rinse off extraction head and accessory tools with clear water.
Lift off solution inlet cover and rinse clean. Remove any debris from stem and cover and wipe clean. After cleaning, reinsert carefully, ensuring stem is properly seated and the cover is pressed down tightly.
Flush out solution lines. Remove solution feed tubes from bottles and place ends in a cup of plain warm water. Switch unit on and operate solution control lever and prespray wand until lines are flushed.
Wipe off feet and rotary head with a damp cloth.
Inspect tank cover seal for tears or rips. Replace if needed.
To maintain appearance, wipe interior and exterior surfaces with a damp cloth. For deep cleaning and a lasting, protective shine, use an automotive interior cleaner.
Check gearcase oil levels. Remove vented gear case plug. While looking into vent plug hole, tilt unit back to allow the rotary head to be turned. Turn the head until the vent plug hole is visibly aligned with the hole in the gear web. Now place the unit flat of the floor or table and insert a screwdriver or similar tool to gauge the oil level. If the oil level is less than 1/8 inch, add Sapphire Scientific gear oil (part number 13-053). Do not overfill. Reinstall vent plug when finished.
WARNING: If a high-pitch vacuum motor sound is heard, TURN UNIT OFF IMMEDIATELY.
Use manual pumpout feature to empty the tank, remove the cover and inspect all three filters.
Clean as necessary.
If poor pumpout performance is observed (i.e., waste tank fills quickly) or if the vacuum motor shut-off is triggered frequently (signaled by a high-pitch vacuum mo-tor sound), inspect pumpout impeller and in tank filter. Rinse filter to clear out debris accumulation. If impeller is pitted, cracked or bent, replace impeller and gasket. See Service Manual.
If excessive consumption of Step 2/3 chemical observed, disassemble and clean inline filters, valves and orifices. See Service Manual.
NOTE: More frequent cleaning and/or replacement may be required in hard water areas.
See Service Manual.
If blower makes excessive noise, bearings or brushes may be worn out. See Service Manual.
Every 50 hours of use
Clean pump check valve and basin. See Service Manual.
Every 500 hours of use
Inspect vacuum blower motor brushes. Replace if needed. See Service Manual.
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 6 Legend Brands, Inc.
Every 1000 hours of use
Inspect pumpout motor brushes. Replace if needed. See Service Manual.
SEE SERVICE MANUAL FOR DETAILED INSTRUCTIONS
SPECIFICATIONS
Name
Dimensions (W × H × D)
Weight
Amps
VersaCarpet VC700
16.0 × 38.3 × 41.7 in.
40.6 × 69.9 × 105.8 cm
125 lbs. | 56.7 kg
11.0/8.5 amps
Circuit 1/Circuit 2
Power 115V/60Hz
Vacuum blower 1350W/105CFM/106 in. H
2
O
Specifications are subject to change without notice. Some values may be approximate.
ACCESSORIES INCLUDED WITH THE VERSACLEAN
67-052 - Duffle Bag with roller wheels
67-049 - Belt Clip Tool Holding System
61-986 - Vacuum Adapter Tube
30-099 - (2) 12awg Extension Cords
67-048 - Soft Jaw Pliers
68-213 - Faucet Adapter Kit
69-532 - Hose/Power Cord Assembly
76-530 - 1 package (4) defoamer pellets
FOR PARTS AND SERVICE CALL YOUR LOCAL
DISTRIBUTOR or Legend Brands at 800-932-3030.
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 7 Legend Brands, Inc.
VERSACLEAN LIMITED WARRANTY
VersaCarpet VC700 Carpet Cleaning Tool
What Does This Warranty Cover?
This warranty is provided to the original purchaser only.
How Long Does This Warranty Last?
We limit all implied warranties to
• One (1) year from the date of purchase on parts and labor;
• Lifetime on frame and rotomolded components
What Legend Brands Will Do:
If a defect in materials or workmanship occurs within the warranty period, Legend Brands at its election will repair or replace the defective part at no charge.
What This Warranty Does Not Cover:
This warranty does not cover or apply to defects due directly or indirectly to misuse, abuse, disassembly, alteration, corrosive chemicals, improper voltage, fire, flood, negligence, accident, improperly or incorrectly performed maintenance or repair, or failure to perform necessary or recommended maintenance or repair (see your Owner’s Manual) or if the use of this product is not in compliance with the instructions and specifications for its use. This warranty does not cover pumpout impellers, fittings, cords, switches, valves, hoses or rubber parts.
OTHER THAN THE WARRANTIES PROVIDED HEREIN, LEGEND BRANDS MAKES NO EXPRESS OR IMPLIED,
ORAL OR WRITTEN WARRANTIES WITH RESPECT TO THIS PRODUCT OR WORKMANSHIP AND ALL WAR-
RANTIES IMPLIED BY LAW INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PAR-
TICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. WE SHALL IN NO EVENT BE LIABLE FOR
DEATH, INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL, CONTINGENT, SPECIAL OR CONSE-
QUENTIAL DAMAGES ARISING FROM USE OF OUR PRODUCTS. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
How Do I Get Service?
In order to be eligible for service under this warranty you MUST do the following: (a) visit warranty.VersaCleanSystems.com and register your purchase to ensure you receive any important product releases; (b) write or call for a return material authorization
(RMA); and (c) have the serial number and original proof of purchase available. Contact us at:
Legend Brands, Inc.
15180 Josh Wilson Road
Burlington, WA 98233
360-932-3030
We will inspect the product without charge and contact you within 72 hours of our receipt of the product to give you the results of our inspection. If our inspection uncovers a defect we will repair or replace the product, at our election. If the product is returned to us on or before ninety (90) days from the date of purchase, we will pay for the cost of shipping it to Legend Brands and the cost to return it to you. If the product is returned to us after the expiration of ninety (90) days from the date of purchase, all shipping costs shall be paid by the purchaser.
If it is determined that there is no defect in the product, or that the defect resulted from causes not within the scope of our warranty, then the product will be repaired or replaced only at your request and at your expense and you must bear all shipping costs.
How Does State Law Apply?
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
VISIT WWW.VERSACLEANSYSTEMS.COM FOR DETAILED INSTRUCTIONS
49-090A VC700 2013-07 8 Legend Brands, Inc.
advertisement
Related manuals
advertisement
Table of contents
- 1 BEFORE YOU BEGIN
- 2 CONTROLS AND COMPONENTS
- 3 BEFORE FIRST USE
- 4 SETUP FOR CARPET CLEANING
- 5 CONTROLS
- 5 Prespray wand. Squeeze lever to release solution. Wand is pressurized by water supply.
- 5 Control rotary head with left hand lever. Grip handle firmly before squeezing lever.
- 5 Control solution flow with right hand lever. Release handle to stop flow.
- 5 To manually pump out tank, press and hold pumpout switch to “Manual” position. Release switch to return to “Auto” mode. Use manual pumpout if excessive foaming occurs and at the end of the job to ensure tank is empty.
- 5 CLEANING PROCEDURES
- 5 TRANSPORTATION AND STORAGE
- 6 MAINTENANCE
- 6 Important: Do not tip unit on its back, or oil may leak.