User’s Guide
600A AC Clamp Meter
Model 38387
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must
refer to the manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use,
hazardous voltages may be present
Double insulation
A UL mark does not indicate that this product has been evaluated for the
accuracy of its readings.
SAFETY NOTES
•
Do not exceed the maximum allowable input range of any function
•
Do not apply voltage to meter when resistance function is selected.
•
Set the function switch OFF when the meter is not in use.
•
Remove the battery if meter is to be stored for longer than 60 days.
WARNINGS
•
Set function switch to the appropriate position before measuring.
•
When measuring volts do not switch to current/resistance modes.
•
Do not measure current on a circuit whose voltage exceeds 240V.
•
When changing ranges using the selector switch always disconnect the test leads
from the circuit under test.
•
Do not exceed the maximum rated input limits.
CAUTIONS
• Improper use of this meter can cause damage, shock, injury or death. Read and
understand this user manual before operating the meter.
•
Always remove the test leads before replacing the battery or fuses.
•
Inspect the condition of the test leads and the meter itself for any damage before
operating the meter. Repair or replace any damage before use.
•
Use great care when making measurements if the voltages are greater than 25VAC
rms or 35VDC. These voltages are considered a shock hazard.
•
Remove the battery if the meter is to be stored for long periods.
•
Always discharge capacitors and remove power from the device under test before
performing Diode, Resistance or Continuity tests.
•
Voltage checks on electrical outlets can be difficult and misleading because of the
uncertainty of connection to the recessed electrical contacts. Other means should be
used to ensure that the terminals are not "live".
•
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
2
38387 V1.4 6/08
Description
1.
Transformer jaws
2.
Data Hold button
3.
Peak Hold button
4.
LCD Display
5.
COM Input Terminal
6.
Jaw opening trigger
7.
Function select switch
8.
Voltage, Resistance Input Terminal
Specifications
Function
AC Current
Range and Resolution
Accuracy (of reading)
199.9 ACA
± (1.5% + 4 digits)
600 ACA
@ 50/60Hz
AC Voltage
600 VAC
DC Voltage
600 VDC
± (1.0% + 1 digits)
Resistance
1999 Ω
± (1.0% + 2 digits)
Jaw size
Opening 1.3" (33mm) approx.
Display
Continuity
3-1/2 digits (2000 counts) LCD
Audible tone < 40Ω approx.
AC bandwidth
Safety compliance
40Hz to 400Hz
IEC 1010-1 and VDE 0411
Operating Temperature
32 to 122 F (0 to 50 C)
Storage Temperature
o
o
o
o
-4 to 140 F (-20 to 60 C)
Over voltage
Cat II 600V
Overload protection
250V AC/DC Spark Gap protection;
PTC protection for Ω range to 250V
Battery
9V battery (IEC 6F22)
Auto Power OFF
After 10 minutes of inactivity
Dimensions/Weight
8x3.2x1.7" (204x80x43mm)/0.62 lbs. (281g)
Safety
For indoor use and in accordance with Overvoltage Category
II, Pollution Degree 2. Category II includes local level,
appliance, portable equipment, etc., with transient
overvoltages less than Overvoltage Cat. III.
3
38387 V1.4 6/08
Operation
NOTICES: Read and understand all warning and precaution statements listed in the
safety section of this operation manual prior to using this meter. Set the function select
switch to the OFF position when the meter is not in use.
AC/DC Voltage Measurements
1. Insert the black test lead into the negative COM terminal and the
red test lead into the positive V terminal.
2.
Set the function switch to the AC or DC voltage range position
(ACV or DCV).
3.
Connect the test leads in parallel to the circuit under test.
4.
Read the voltage measurement on the LCD display.
AC Current Measurements
WARNING: Ensure that the test leads are disconnected from the meter before making
current clamp measurements.
1. Set the Function switch to the 600 or 200A range. If the range of the
measured is not known, select the higher range first then move to
the lower range if necessary.
2. Press the trigger to open jaw. Fully enclose one conductor to be
measured.
3. The clamp meter LCD will display the reading.
Resistance and Continuity Measurements
1. Insert the black test lead into the negative COM terminal and the red test lead into the
Ω terminal.
2. Set the function switch to the Ω •))) position.
3. Touch the test probe tips across the circuit or component under test. It is best to
disconnect one side of the device under test so the rest of the circuit will not interfere
with the resistance reading.
4. For Resistance tests, read the resistance on the LCD display.
5. For Continuity tests, if the resistance is < 40Ω, a tone will sound.
Data Hold
To freeze the LCD meter reading, press the data hold button. The data hold button is
located on the left side of the meter (top button). While data hold is active, the DH display
icon appears on the LCD. Press the data hold button again to return to normal operation.
Peak Hold
To hold the highest reading on the LCD, press the peak hold button. The peak hold button
is located on the left side of the meter (bottom button). The meter reading will not change
as readings change, rather it will only display the highest reading encountered since the
peak hold button was pressed. Press the peak hold button again to return to normal
operation.
4
38387 V1.4 6/08
Maintenance
WARNING: To avoid electrical shock, disconnect the meter from any circuit, remove the
test leads from the input terminals and turn OFF the meter before opening the case. Do
not operate with open case.
Cleaning and Storage
Periodically wipe the case with a damp cloth and mild detergent; do not use abrasives or
solvents. If the meter is not to be used for periods of longer than 60 days, remove the battery
and store it separately
Battery Replacement
1. Remove the three rear Phillips head screws
2.
Open the battery compartment
3.
Replace the 9V battery
4.
Re-assemble the meter
Warranty
EXTECH INSTRUMENTS CORPORATION (A FLIR COMPANY) warrants this instrument to
be free of defects in parts and workmanship for one year from date of shipment (a six
month limited warranty applies to sensors and cables). If it should become necessary to
return the instrument for service during or beyond the warranty period, contact the
Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our
website www.extech.com for contact information. A Return Authorization (RA) number
must be issued before any product is returned to Extech. The sender is responsible for
shipping charges, freight, insurance and proper packaging to prevent damage in transit.
This warranty does not apply to defects resulting from action of the user such as misuse,
improper wiring, operation outside of specification, improper maintenance or repair, or
unauthorized modification. Extech specifically disclaims any implied warranties or
merchantability or fitness for a specific purpose and will not be liable for any direct, indirect,
incidental or consequential damages. Extech's total liability is limited to repair or
replacement of the product. The warranty set forth above is inclusive and no other
warranty, whether written or oral, is expressed or implied.
Calibration and Repair Services
Extech offers repair and calibration services for the products we sell. Extech also
provides NIST certification for most products. Call the Customer Care Department for
information on calibration services available for this product. Extech recommends that
annual calibrations be performed to verify meter performance and accuracy.
Support line (781) 890-7440
Technical Support: Extension 200; E-mail: [email protected]
Repair & Returns: Extension 210; E-mail: [email protected]
Product specifications subject to change without notice
For the latest version of this User Guide, Software updates, and other
up-to-the-minute product information, visit our website: www.extech.com
Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451
Copyright © 2008 Extech Instruments Corporation (a FLIR company)
All rights reserved including the right of reproduction in whole or in part in any form.
5
38387 V1.4 6/08
6
38387 V1.4 6/08
">
