Digital Watchdog DWC-MC253WTIR Star-Light™ UHDoC® 2.1MP/1080p micro dome Installation Guide

Quick Start Guide

DW® Universal HD over Coax® micro dome cameras

DWC-MC253WTIR DWC-MC253W-28

STEP 1 – PREPARING TO MOUNT THE CAMERA

1. The mounting surface must withstand five times the weight of your camera.

2. Pay attention to the cables. The can easily become caught and damaged. Any damage may cause a short or fire.

3. Detach the camera’s dome cover by removing the security screw from the decorative ring.

4. This product is intended to be supplied by a UL Listed Power Supply

Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.24A min

(DWC-MC253WTIR) and 0.14A min (DWC-MC253W-28).

Protective sheet

Quick Start Guide

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES

Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.

Power requirements

12VDC ONLY!

CAUTION! The camera supports

DC power supply only

Power consumption

DC12V (LED off): 1.7W

DC12V (LED on): 2.9W

Black and white decorative rings

Test video cable

Screws and plastic anchors-4pcs

External OSD and signal controller

WHAT’S IN THE BOX

1 set Star wrench

1

Mounting template

1 set

Quick set up guide

1

DC plug cable

1

1

1

1

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in

the ‘Search by Product’ search bar. Results for

applicable part numbers will populate automatically

based on the part number you enter.

3. Click . All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

Attention: This document is intended to serve as a quick reference for initial setup. It is recommended that the user read the entire instruction manual for complete and proper installation and usage.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00AM – 8:00PM EST, Monday through Friday digital-watchdog.com

STEP 3 – CHANGING THE SIGNAL IN

THE CAMERA

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To switch between the signals: a. Remove the camera’s dome and connect the external controller to the base of the camera. See the image below for more information. b. Use the OSD Switch to switch

the camera’s signal.

• To switch the camera to

HD-TVI mode, press OSD joystick to the left for 5 seconds.

• To switch the camera to

HD-Analog mode, press OSD joystick to the right for 5 seconds.

• To switch the camera to CVBS mode, press OSD joystick up for 5 seconds.

• To switch the camera to

HD- CVI mode, press OSD joystick down for 5 seconds.

OSD board

Quick Start Guide

STEP 4 – INSTALLING THE CAMERA

1. Once all cables have been connected, use the screws included with the camera to properly mount and secure the camera to the mounting surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired view. The cameras’ max angles are:

Pan: 0° ~ 360°

Tilt: 0° ~ 70° IR Switch

ON/OFF

Rotation: 0° ~ 360°

3. Once the installation is complete, remove the protective film from the camera’s dome cover.

4. For DWC-MC253WTIR models, the camera has a manual IR switch, located under the camera’s lens. You can use this switch to manually turn the IR LED board on or off according to the installation needs.

External OSD and signal controller

Panning 360°

Rotation 360°

Titling 70°

External OSD and signal controller

Rev Date: 06/21

Copyright © Digital Watchdog. All rights reserved.

Specifications and pricing are subject to change without notice.