advertisement
Port Engine Serial Number:
Stbd. Engine Serial Number:
Hull Identification Number:
The Hull Identification Number (HIN) is located on the starboard side of the transom. Be sure to record the HIN (and the engine serial numbers) in the space provided above. Please refer to the HIN for any correspondence or orders.
HIN LOCATION
© 1999 Bayliner Technical Publications. All rights reserved.
No part of this publication may be reproduced, stored in any retrieval system, or transmitted in any form by any means, electronic, mechanical, photocopying, recording or otherwise, without prior written permission of Bayliner.
Printed in the United States of America.
General Notes
The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, Bayliner assumes no liability resulting from errors or omissions in this document, or from the use of information contained herein.
Due to our commitment to product improvement, Bayliner reserves the right to make changes in the product design, specifications, and equipment at any time without notice or obligation. Illustrations and/or photos may show optional equipment.
All Bayliner products meet or exceed USCG (Unites States Coast Guard) and/or NMMA (National Marine Manufacturer’s
Association) construction standards. Manufactured with 1,1,1 Trichloroethane, a substance which harms public health and environment during the manufacturing process by destroying ozone in the upper atmosphere.
Proprietary Rights
This document discloses subject matter in which Bayliner has proprietary rights. The information and design disclosed herein were originated by and are the property of Bayliner. Neither receipt nor possession thereof confers or transfers any right to reproduce, copy, alter or disclose the document or any part thereof, any information contained therein, or to construct boats or any item from it, except by written permission from or written agreement with Bayliner. This document is to be returned upon request to Bayliner.
Congratulations and welcome aboard your new Bayliner Ciera!
Thank you for choosing our product. Bayliner is committed to the goal of building the highest quality products in the marine industry and to providing the finest after-thesale support in the world.
To keep our respected status as the number one boat builder in the world, Bayliner has instituted an ongoing Total Customer Satisfaction Program.
The guiding principles of this program are:
•
Design, build and support the finest marine products in the world, in every market we serve.
•
Be personally and individually responsible for the customer’s total satisfaction.
•
Remember that every customer has a choice, and we want them to choose Bayliner!
Welcome to the Bayliner family. We are looking forward to serving your boating needs, now and in the future!
CONTENTS
Chapter 1: Welcome Aboard!
1
Dealer Service
1
Boating Experience
1
Engines/Accessories Guidelines
1
Safety Standards
2
Qualified Maintenance
2
Structural Limitations
2
Special Care For Moored Boats
3
Hazard Warning Symbols
Chapter 2: Components/Systems
4
Dimensions & Tank Capacities
4
Boat Lifting
5
Hullside Exterior Hardware & Drains
6
Deck Equipment
6
Electrical System
7
DC Electrical System
9
AC Electrical System
13
Audio & Visual Equipment
13
Navigation & Communication Equipment
14
Lighting
14 Navigation and Interior Lights
14
Appliances
15
Propulsion
15 Engine Room Ventilation System
17
Controls
17 Steering & Shifter/Throttle System
17
Bilge
19
Fuel System
20 Anti-siphon Valves (Gas Only)
21
Freshwater System
23 Sink & Shower Drain Systems
23
Seawater Systems
24
Air Conditioning & Heating (Option)
26
Marine Head System & Waste Tank
27 Macerator Delete Head System (Option)
27
Labels
Appendix A: Wiring Schematics
32 Hull Harness (Diesel Option)
35 Ignition Panel Harness (Gas)
35 Large Dash Switch Panel Harness
Appendix B: Electrical Routings
38 Positive Battery Cable Harness
39 Negative Battery Cable Harness (Gas)
39 Negative Battery Cable Harness (Diesel
40 Windlass Cable Harness (Optional)
Appendix C: Limited Warranty
1
Chapter 1: Welcome Aboard!
This Owner’s Manual Supplement was prepared to provide specific information about your boat. Please study the Owner’s Manual and this Owner’s Manual Supplement carefully, paying particular attention to Appendix C:
Limited Warranty.
Keep this Supplement and all of the literature provided in your owner’s packet on your boat in a secure, yet readily available place.
Dealer Service
Make certain that you receive a full explanation of all systems from the selling dealer before taking delivery of your boat. Your selling dealer is your key to service. If you experience any problems with your new boat, immediately contact the selling dealer. If for any reason your selling dealer is unable to help, you can call us direct on our customer service hotline: 360-435-8957 or send us a FAX: 360-403-4235.
Boating Experience
If this is your first boat or if you are changing to a type of boat you are not familiar with, for your own comfort and safety, please ensure that you obtain handling and operating experience before assuming command of the boat.
We strongly recommend that you take one of the boating safety classes offered by the U.S. Power Squadrons or the U.S. Coast Guard Auxiliary. For more course information, including dates and locations of upcoming classes, contact the organizations directly:
• U.S. Power Squadrons: 1-888-FOR-USPS (1-888-367-8777) or on the Internet at: http://www.usps.org
• U.S. Coast Guard Auxiliary: 1-800-368-5647 or on the Internet at: http://www.cgaux.org
Outside the United States, your selling dealer, national sailing federation or local yacht club can advise you of local sea schools or competent instructors.
!
WARN I NG!
CONTROL HAZARD!
• A qualified operator must be in control of the boat at all times.
• Do not operate your boat while under the influence of alcohol or drugs.
Engines/Accessories Guidelines
Your boat’s engines and accessories were selected to provide optimum performance and service. Installing different engines or other accessories may cause unwanted handling characteristics. Should you choose to install different engines or to add accessories that will affect the boat’s running trim, have an experienced marine technician perform a safety inspection and handling test before operating your boat again.
The engines and accessories installed on your boat come with their own operation and maintenance manuals. We strongly urge you to read and understand these manuals before operating the engines and accessories.
Safety Standards
Your boat’s mechanical and electrical systems were designed to meet safety standards in effect at the time it was built. Some of these standards were mandated by law, all of them were designed to insure your safety, and the safety of other people, vessels and property.
In addition to this Owner’s Manual Supplement, please read the Owner’s Manual, the engine manual and all accessory literature included in the owner’s packet for important safety standards and hazard information.
!
PERSONAL SAFETY HAZARD! Do not allow anyone to ride on parts of the boat not designated for such use. Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding or occupying the transom platform while underway is especially hazardous and will cause personal injury or death.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
2 Chapter 1: Welcome Aboard!
Qualified Maintenance
!
WARN I NG!
To maintain the integrity and safety of your boat, only qualified personnel should perform maintenance on, or in any way modify: The steering system, propulsion system, engine control system, fuel system, environmental control system, electrical system or navigational system.
Failure to maintain your boat’s systems (listed in the warning above) as designed could violate the laws in your jurisdiction and could expose you and other people to the danger of bodily injury or accidental death. We recommend that you follow the instructions provided in the Owner’s Manual, this Owner’s Manual Supplement, the engine owner’s manual and all accessory instruction sheets/manuals included in your boat’s owner’s packet.
Structural Limitations
The transom platform and bow platform are designed to be lightweight for proper boat balance. The load limit for these platforms is 30 pounds per square foot, evenly distributed.
Special Care For Moored Boats
If moored in saltwater or fresh water, your boat will collect marine growth on its hull bottom. This will detract from the boat’s beauty, greatly affect its performance and may damage the gelcoat. There are two methods of slowing marine growth:
• Periodically haul the boat out of the water and scrub the hull bottom with a bristle brush and a solution of soap and water.
• The hull below the waterline was painted with anti-fouling paint by the factory. Occasionally you will need to repaint it with a good grade of anti-fouling paint.
NOTI C E
² To help seal the hull bottom and reduce the possibility of gelcoat blistering on moored boats, we recommend the application of an epoxy barrier coating, such as INTERLUX, Interprotect
2000E/2001E. The barrier coating should be covered with several coats of anti-fouling paint.
² Many states regulate the chemical content of bottom paints in order to meet environmental standards. Check with your local dealer about recommended bottom paints, and about the laws in effect in your area.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 1: Welcome Aboard! 3
Hazard Warning Symbols
The hazard warning symbols shown below are used throughout this Supplement and your boat to call attention to potentially dangerous situations which could lead to either personal injury or product damage. We strongly urge you to familiarize yourself with these warning symbols as well as the ISO symbols listed in
Appendix C
carefully and follow all safety recommendations.
!
DAN GER!
This symbol alerts you to immediate hazards which WILL cause severe personal injury or death if the warning is ignored.
!
WARN I NG!
This symbol alerts you to hazards or unsafe practices which COULD result in severe personal injury or death if the warning is ignored.
!
CAUTI O N!
This symbol alerts you to hazards or unsafe practices which COULD result in minor personal injury or cause product or property damage if the warning is ignored.
NOTI C E
This symbol calls attention to installation, operation or maintenance information, which is important to proper operation but is not hazard related.
EXPLOSION
HAZARD!
OPEN FLAME
HAZARD!
HOT
HAZARD!
ELECTRICAL
HAZARD!
PERSONAL INJURY
& FALLING HAZARD!
ROTATING
PROPELLER HAZARD!
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
4
Chapter 2: Components/Systems
Dimensions & Tank Capacities
Length Overall (LOA) - 31’ 6”
Length Rigged - 32’ 2”
Weight - 11,741 lb.
Beam - 11’ 0”
Draft Hull - 1’ 9”
Draft Max. - 2’ 9”
Bridge Clearance - 7’ 10”
Bridge Clearance Max. - 9’ 7”
Fuel Tank Capacity - 148 gal.
Waste Holding Tank Capacity - 30 gal.
Freshwater Tank Capacity - 35 gal.
transom platform transom gate boarding ladder transom stowage engine hatch battery board buddy seat helm station hanging locker microwave stove
Boat Lifting
• Always follow the lift equipment’s recommendations and requirements.
• If water is present in the bilge, pump water out of the bilge areas before lifting your boat. Excessive amounts of bilge water can shift and change the balance of the load.
LIFTING SLING LABELS
(TYPICAL PORT & STARBOARD)
2’ 13’ 6”
AFT SLING
POSITION
FORWARD
SLING POSITION
REFERENCE
POINT
Sling Placement
When lifting your boat, always position the lifting slings along the port and starboard sling label positions as shown in the illustration above.
!
CAUTI O N!
PRODUCT OR PROPERTY DAMAGE HAZARD!
• When lifting any boat, always use a spreader bar. The spreader bar must be equal to the width of the boat at the lifting point.
• Lift slings may slip on the hull. Avoid serious injury or death by securing the slings together before lifting.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Hullside Exterior Hardware & Drains
STARBOARD HULLSIDE VIEW
WATER TANK VENT
FUEL TANK VENT
Chapter 2: Components/Systems 5
PORTLIGHTS (TYPICAL)
BILGE PUMP
DRAIN
COCKPIT
DRAIN
ICE TUB
DRAIN
ROPE LOCKER
DRAIN
BOW EYE
AIR CONDITION
DRAIN (OPTION)
PORT HULLSIDE VIEW
FORWARD BILGE
PUMP DRAIN
SHOWER SUMP
PUMP DRAIN
WASTE TANK
VENT COCKPIT
DRAIN MACERATOR
PUMP
OVERBOARD
AIR CONDITION
SUMP PUMP DRAIN
(OPTIONAL)
GALLEY SINK DRAIN
HEAD SINK DRAIN
STEP
DRAIN
GENERATOR
EXHAUST
(OPTION)
TRANSOM VIEW
BOARDING LADDER
STERN EYE (TYPICAL)
TRIM TAB (TYPICAL)
ZINC PLATE
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
6 Chapter 2: Components/Systems
Deck Equipment
Anchor Windlass (Option)
Your boat may feature an optional anchor windlass. Please read the manufacturer’s instruction manual supplied in your boat’s owner’s packet before using the anchor windlass for the first time.
• The windlass can be controlled from a switch at the helm or from the deck switches (see illustration to right).
• Verify that the windlass breaker, located under the aft cockpit entertainment center sink, is activated before using the anchor windlass.
• To haul the anchor, use engine power (not the windlass) to move the boat to, and directly above, the anchor. Activate the windlass to disengage the anchor from the bottom by pulling it straight up. Do not pull the boat to the anchor using the windlass or continue to operate the windlass if it has stalled or is overloaded.
Windshield Wipers
• The windshield wiper switch is located on the helm’s large switch panel.
• Periodically, due to wear and environmental exposure, you will need to replace wiper blades using 18” blade refills.
Large Helm Switch Panel
ANCHOR WINDLASS LOCATION
(VIEW OF FOREDECK)
WINDLASS DECK
SWITCHES
WINDLASS
SPOTLIGHT (OPTION)
PORT
WINDLASS BREAKER LOCATION
(VIEW OF PORT AFT COCKPIT)
ENTERTAINMENT
CENTER SINK
WINDLASS
BREAKER
Electrical System
We strongly recommend you thoroughly read and understand this section, the electrical section of the Owner’s
Manual and all accessory manuals included in your boat’s owner’s packet. Wiring schematics are provided in
Appendix A of this supplement; electrical routing illustrations in Appendix B.
!
DANGER!
EXTREME FIRE, SHOCK & EXPLOSION HAZARD!
• Do not modify the electrical systems or relevant drawings. Only qualified personnel should install batteries and/or perform electrical system maintenance.
• To minimize the risks of fire and explosion, never install knife switches or other arcing devices in the fuel compartments. Never substitute automotive parts for marine parts.
Electrical, ignition and fuel system parts were designed and manufactured to comply with rules and regulations that minimize risks of fire and explosion.
• Insure that all battery switches are in the off position before performing any work in the engine spaces.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 7
!
WARN I NG!
FIRE, OPEN FLAME & EXPLOSION HAZARD!
• Fuel fumes are heavier than air and will collect in the bilge areas where they can be accidently ignited. Visually and by smell (sniff test), check the engine and fuel compartments for fumes or accumulation of fuel. Always operate the bilge blowers for at least four minutes prior to engine starting, electrical system maintenance or activation of electrical devices.
• Minimize the danger of fire and explosion by not exposing batteries to open flame or sparks. It is also important that no one smoke anywhere near the batteries.
!
CAUTI O N!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
Never disconnect the battery cables while the engine is running since damage may occur to your boat’s electrical system components.
NOTI C E
Electrical connections are prone to corrosion. To reduce corrosion-caused electrical problems, keep all electrical connections clean and apply a spray-on protectant that is designed to protect connections from corrosion.
DC Electrical System
Your boat is equipped with a 12 volt DC (direct current) system. The
DC breaker panel is located at the helm, just below the ignition panel.
Fuses and Circuit Breakers
• Fuses and circuit breakers for engines and main accessory power are on the DC main distribution panel and on the battery switch panel.
• Electronics power is provided at the helm station.
• Some equipment, such as depth finders, may have secondary fuse protection at the unit.
Batteries
The batteries installed on your boat supply electricity for lights, accessories as well as engine and optional generator starting.
• The starboard engine battery supplies accessory power and the port engine battery supplies power to the optional generator.
• The port and starboard engine battery conditions can be read on the helm’s instrument panel voltage gauges (voltmeters).
Battery Maintenance
• Periodically remove the battery caps and check the electrolyte level; if the zinc plates are exposed, add distilled water until they are covered.
• Corroded battery terminals can be cleaned with baking soda and water. After cleaning the terminals, coat them with a light film of battery terminal lubricant and tighten all battery connections.
AFT
DC PANEL
BATTERY LOCATIONS
STARBOARD ENGINE/
ACCESSORY BATTERY
PORT ENGINE/OPTIONAL
GENERATOR BATTERY
VIEW OF HELM
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
8 Chapter 2: Components/Systems
Battery Switches
Two rotary battery switches are installed on your boat. The battery switches are located under the aft cockpit entertainment center sink and should be switched to the off position whenever the boat is left unoccupied for long periods of time.
Starting Positions
When starting your boat’s engines or optional generator, the engine battery switch selector should be placed into position “2”.
Normal Battery Switch Positions
After starting your boat’s engines, the engine battery switch selector should be kept in position “2” and the house battery selector switch should be set to position “1”. These normal operating positions ensure proper charging of the port and starboard batteries while the engines are running.
Parallel Battery Switch Positions
When one or both battery switches are placed in the “BOTH” position, power is drawn from both batteries to allow emergency starting of the engines. Only in an emergency should a battery switch be placed in the “BOTH” position. When the emergency situation is resolved, the battery switch selector should immediately be switched back to its normal operating position.
!
CA UTI ON!
SYSTEM DAMAGE HAZARD!
• Never disconnect battery cables or turn off battery switches while engines are running as this can cause damage to your boat’s electrical components.
• Battery switches should be placed in the parallel (BOTH) position only in an emergency and returned to their normal operating positions once the emergency is over.
BATTERY SWITCH PANEL LOCATION
(VIEW OF COCKPIT ENTERTAINMENT CENTER)
ENTERTAINMENT
CENTER SINK
PORT
BATTERY
SWITCH
PANEL
NORMAL BATTERY
SWITCH POSITIONS:
ENGINE BATTERY
SWITCH TO
POSITION “2”
HOUSE BATTERY
SWITCH TO
POSITION “1”
Alternators
The alternators installed on your boat maintain proper charge levels of your boat’s batteries during engine operation.
Battery Charger
Your boat is equipped with a battery charger. We recommend that you thoroughly read and understand the battery charger manual (provided in your boat’s owner’s packet) before using the battery charger for the first time.
• The battery charger’s circuit breaker is located on the AC panel and must be turned on for charging to occur.
• The battery charger will charge the batteries whenever the boat is plugged into shore power or whenever the
optional generator is operating.
!
CAUTI O N!
The battery charging systems (alternator and battery charger) installed on your boat are designed to charge conventional lead-acid batteries. Before installing gel-cell or other new technology batteries, consult with the battery manufacturer about charging system requirements.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 9
AC Electrical System
Your boat uses a 120v/60Hz AC (alternating current) system.
Τ he AC system can be energized by shore power or optional generator power.
This system is designed so that ship’s power and shore power sources cannot supply power simultaneously.
The AC panel’s master circuit breakers provide power source selections to the accessory breakers that are directly below the designated master breaker. After activating AC power, individual breakers must be activated to supply power to the accessories you wish to use.
AC PANEL LOCATION
(VIEW OF GALLEY)
AC PANEL
(INSIDE)
!
C AUTI ON!
• SYSTEM DAMAGE HAZARD! When using shore power or generator power, the simultaneous operation of several AC accessories can result in an overloaded circuit. It may be necessary to turn off one accessory while operating another.
• WATER HEATER DAMAGE HAZARD! Do not energize the water heater electrical circuit on the AC panel until the heater is completely filled with water. Even momentary operation in a dry tank will damage the heating elements.
Warranty replacements will not be made on elements or tank damaged in this manner.
Shore Power
Your standard-equipped boat features one 120v/30 amp shore power receptacle, located on the port side of the deck.
NOTI C E
Some dockside installations may be rated less than 30 amps, therefore, you may need to purchase lower amp adapters. Whenever a lower amp adapter is used, however, there will be a corresponding drop in supplied power from the dockside system.
If your boat is equipped with an optional air conditioning system, a second 30 amp inlet has been installed next to the existing shore power inlet. When both inlets are installed, the inlets are labeled line one and line two, which corresponds to the line one and line two master breakers on the AC panel.
This system is designed so that each line operates independent of each other.
SHORE POWER INLET LOCATIONS
30 AMP SHORE POWER INLET
(AIR CONDITION OPTION)
STANDARD
30 AMP SHORE
POWER INLET
PORT
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
10 Chapter 2: Components/Systems
!
DANGER!
FIRE, EXPLOSION & SHOCK HAZARD!
• Do not alter shore power connectors and use only compatible connectors.
• Before connecting to shore power, ensure all breakers and switches on the AC master panel are in the off position.
• To prevent shock or injury from an accidental dropping of the “hot” cord into the water,
always attach the shore power cord to the boat inlet first; then to the dockside connection.
When disconnecting the shore power cable, always disconnect the shore power cable at the dockside outlet first.
• Close the shore power inlet cover tightly when not in use.
!
CAUTI O N!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
•
Ν
ever connect dockside power to your boat outside North America unless you have purchased the international electrical conversion option.
• The simultaneous use of several AC components can result in an overloaded circuit. It may be necessary to turn off one or more accessories in order to use another accessory.
• Use double insulated or three-wire protected electrical appliances whenever possible.
• Never switch the AC panel’s master breaker to the generator position while connected to shore power.
Connecting To Shore Power
!
WARN I NG!
SHOCK & ELECTRICAL SYSTEM DAMAGE HAZARD!
• You must monitor the polarity indicator lights every time you connect to shore power.
• When connecting to shore power and you encounter a reversed polarity light (red colored), do not energize the main breaker switches. Instead, immediately disconnect the shore power cord from the dockside receptacle first and notify marina management.
1.
Monitor the AC panel’s polarity indicator lights as follows:
• A green light illuminating after the power cord is plugged into the boat’s external power receptacle indicates acceptable electrical power. You may energize the master breaker switch.
• A red light, however, indicates reversed polarity, which could cause electrical system damage and possibly electrical shock injuries. In this case,
do not energize the master breaker switch (see previous warning).
2.
Activate the AC system by turning the ship/shore master breaker to the dockside position.
3.
Turn on the master breaker and individual component breakers as required.
AC PANEL (SHOWN WITH OPTIONAL SHORE POWER INLET)
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
LOCKOUT
RED GRN
AC VOLTS
GENERATOR
LOCKOUT
RED GRN
Chapter 2: Components/Systems 11
NOTI C E
• If equipped with two shore power inlets, the AC panel will have two independent master breakers installed, labeled line one and line two which correspond to line one and line two shore power inlets. A master breaker energizes the component breakers that are positioned
directly below that master breaker. To activate component breakers below the other master breaker, shore power or (optional) generator power must be supplied to the other shore power inlet.
• Voltage can be read on the AC panel’s voltmeter by setting the voltmeter selector switch.
Generator Power (Option)
Your boat may be equipped with an optional gas or diesel generator. Prior to initially operating your generator, read the generator manual for detailed information on pre-start checks, break-in procedures and starting instructions.
!
CAUTI O N!
SYSTEM DAMAGE HAZARD!
• Always verify that the generator’s seawater intake valve (seacock) is in the open position prior to starting the generator and keep the seacock open until the generator is turned off.
• Never operate the generator starter for more than 30 seconds. If the generator does not start, wait at least 30 seconds before another start attempt is made.
• After starting the generator, wait for the generator to stabilize before activating component breakers on the AC panel.
• Never switch the AC panel’s master breaker to the shore power position while the generator is operating.
Observe the following about your generator:
• Polarity has been established in the installation of the generator, therefore the polarity lights will not function while in this mode.
• The generator’s main circuit breaker is located on the generator.
• The generator runs off the port engine battery.
• In addition to servicing the filters attached to the generator, the filter/separator (located near the fuel line valves) should be serviced as described in the manufacturer’s manual.
• The coolant mixture installed at the factory consists of equal parts of water and anti-freeze (Ethylene Glycol). The coolant bottle for the generator is located on the forward bulkhead in the generator compartment.
• Frequently check the generator’s seawater strainer for leaks and/or debris as outlined in the seawater strainer section of this Supplement.
• To monitor the voltage generated by the generator, switch the voltage selector switch to the generator position.
Diesel Generator Operation
1.
Open the main generator’s seawater intake valve (seacock) before starting the generator and keep the seacock valve open during generator operation.
2.
Operate the bilge blowers for a minimum of four minutes prior to starting the generator. The blower switch is located on the AC panel near the generator controls. If your boat is running below cruising speed, leave the blowers on while the generator is operating.
3.
Verify that the port engine battery switch is turned on.
4.
On the AC panel (see drawing on previous page), press and hold the pre-heat switch on for one minute to allow for pre-heating. While holding the generator’s pre-heat switch, activate the start switch. As the engine starts, continue to hold the pre-heat switch until oil pressure is indicated on the pressure gauge.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
12 Chapter 2: Components/Systems
5.
Slide the master breaker lockout from dockside power to generator power.
6.
Switch the sub-main breaker on.
7.
Activate each individual component breaker as required.
To shut off the generator, hold the “off” switch until the generator completely shuts down.
Diesel Generator Routing
WATER PICK UP AND EXHAUST ROUTING FUEL ROUTING
TO EXHAUST
THRU-HULL
EXHAUST
HOSE
SHUT OFF
VALVE
FUEL FILTER
GENERATOR
FUEL HOSE
(TYPICAL)
OVERFLOW
BOTTLE
GENERATOR
RETURN
MUFFLER
SEAWATER
INTAKE VALVE
(SEACOCK)
WATER
HOSE
SEAWATER
STRAINER
AFT
FUEL TANK
GENERATOR
WITHDRAWAL
Gas Generator Routing
FWD.
WATER
HOSE
SEAWATER
STRAINER
FUEL FILTER
SIPHON BREAK
VENTED LOOP
TO
THRU-HULL
SEAWATER INTAKE
VALVE (SEACOCK)
TO HULLSIDE
EXHAUST VENT
EXHAUST HOSE
PORT
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
FUEL TANK
WITHDRAWAL
MUFFLER
FUEL
TANK
Chapter 2: Components/Systems 13
Gas Generator Operation
1.
Open the main generator’s seawater intake valve (seacock) before starting the generator and keep the seacock valve open during generator operation.
2.
Operate the bilge blowers for a minimum of four minutes before starting the generator. The blower switch is located on the AC panel near the generator controls (see AC panel layout on page 9). If your boat is running below cruising speed, leave the blowers on while the generator is operating.
3.
Verify that the port engine battery switch is turned on.
4.
On the AC panel, simultaneously press the oil pressure button (labeled pre-heat) and activate the start switch.
5.
Slide the master breaker from dockside power to generator power.
6.
Switch the sub-main breaker on.
7.
Activate each individual component breaker as required.
To shut off the generator, hold the “off” switch until the generator completely shuts down.
Audio & Visual Equipment
All audio and visual equipment installed on your boat have separate instruction sheets or manuals that explain their operating procedures in detail.
NOTI C E
AM radio reception may be impaired anytime the engines are running.
Navigation & Communication Equipment
The owner’s packet contains operation manuals for all navigation & communication equipment installed on your boat. We strongly recommend that you thoroughly read and understand these manuals before using these systems.
Additionally, carefully read the warnings below and follow all safety recommendations.
Compass
Your boat is equipped with a compass at the helm.
NOTI C E
Compass accuracy can be affected by many factors. We strongly recommend having a qualified technician calibrate your compass. Make sure the technician gives you a deviation card which shows the corrections to apply in navigational calculations. Keep a copy of the deviation card at the helm.
Depth Finder (Option)
Your boat may feature an optional depth finder (depth sounder) at the helm station. The depth finder provides you with measurements of water depth beneath the boat.
!
WARN I NG!
• Do not use the depth finder as a navigational aid to prevent collision, grounding, boat damage or personal injury.
• When the boat is moving, submerged objects will not be seen until they are already under the boat. Bottom depths may change too quickly to allow time for the boat operator to react.
If you suspect shallow water or submerged objects, operate the boat at very slow speeds.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
14 Chapter 2: Components/Systems
VHF Radio (Option)
Your boat may include an optional VHF (Very
High Frequency) radio at the helm.
The VHF radio can be used to access weather reports, summon assistance or contact other vessels as permitted by the FCC (Federal Communications Commission). Contact the FCC for licensing, rules and regulations concerning
VHF radio usage.
GAUGE PANEL
COMPASS
HELM LAYOUT
SWITCH
PANELS
SHIFTER/
THROTTLE
SPOTLIGHT
CONTROL
(OPTION)
LIGHT
Lighting
STEERING
WHEEL
Navigation and Interior Lights
We strongly recommend that you understand navigation light usage by reading the navigation light section of the Owner’s Manual.
The navigation and interior lights supplied with your boat are of top quality, but you should be aware that failure may periodically occur for a variety of reasons:
IGNITION PANEL
DC BREAKER PANEL
VHF (OPTION)
LIGHT
MACERATOR
SWITCHES
• There may be a blown fuse - replace the fuse in the switch panel.
• The bulb may be burned out - carry spare bulbs for replacement.
• The bulb base may be corroded - clean the base and coat it with non-conductive electrical lubricant.
• A wire may be damaged or may have come loose - repair as required.
TRIM TAB
SWITCHES
HELM
STORAGE
TUB
!
CAUTI O N!
• Avoid the storage of gear where it would block navigation lights from view.
• Conserve battery usage. Prolonged operation of cabin interior lights (overnight) will result in a drained battery.
Spotlight (Option)
Your boat may come equipped with an optional spotlight (located on the bow rail) which can be controlled by a switch at the helm. Operating instructions can be found in the spotlight’s operating manual (included in your boat’s owner’s packet).
Appliances
All appliances installed on your boat come with their own manuals (supplied in your boat’s owner’s packet) that explain detailed operating instructions and important safeguards. Thoroughly read and understand these manuals before attempting to operate your boat’s appliances.
• Appliances operate on 120 volt AC power, which may be supplied from shore power or optional generator power.
• Make sure the AC panel breaker is activated for the appliance you wish to turn on.
Water Heater
!
CAUTI O N!
SYSTEM DAMAGE HAZARD! The water heater must be kept full of water to avoid damage to the 120 volt heating element. The water heater should also be drained and the power turned
OFF when the possibility of freezing exists.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 15
Alcohol/Electric Stove
!
WARN I NG!
EXPLOSION, SCALDING & FIRE HAZARD!
• The stove manufacturer’s instructions and safety suggestions must be followed closely to avoid serious burns and to prevent creating fire hazards.
• Do not touch stove burners, grates or areas near the stove units as they may be hot even when they are dark in color. Areas near burners and grates may become hot enough to cause burns. Always keep an approved ABC-type fire extinguisher in galley area.
• Do not operate the stove while underway.
!
CAUTI O N!
To prevent overheating which can destroy the electric burner elements, never attempt to use both alcohol and electric burners simultaneously.
Propulsion
VIEW OF AFT COCKPIT
Engines
The owner’s packet contains detailed engine operation and maintenance manuals. Be sure to read and understand these manuals before operating or performing maintenance to the engines.
Engine Access
The engine compartment can be accessed through the aft cockpit engine hatch after lowering the transom jump seat.
ENGINE
HATCH
Engine Room Ventilation System
The bilge blowers remove fumes from the engine compartment and draws fresh air into the compartment through the deck vents. To ensure fresh air circulation, operate the bilge blowers for at least four minutes prior to starting the engines (or optional generator), during starting, and while operating your boat below cruising speed.
!
WARN I NG!
EXPLOSION HAZARD!
• Operation of the blower system is not a guarantee that explosive fumes have been removed.
If you smell any fuel, do not start the engines. If the engines are already running, immediately shut off the engines and all electrical accessories and investigate immediately.
• Do not obstruct or modify the ventilation system.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
16 Chapter 2: Components/Systems
Gas Bilge Blower Routing
UNDERSIDE VIEW OF DECK
VIEW OF ENGINE
COMPARTMENT
A
IR HOSE ROUTES TO
ENGINE COMPARTMENT
AIR
BLOWERS
AFT
TO BLOWERS
MOUNTED ON DECK
Engine Cooling System
The engine cooling system circulates seawater around components on the engine to reduce engine temperature.
• If your boat is equipped with seawater strainers, the strainers should be checked for leaks and debris every time you use your boat. For instructions on how to clean the seawater strainers of debris, see the seawater strainer section of this Supplement.
• If your boat is equipped with a closed coolant system, the engine coolant (anti-freeze) levels should be checked at the enginemounted expansion tanks and at the coolant recovery bottles.
OPTIONAL DIESEL ENGINE COOLING SYSTEM ROUTING
TO GIMBLE HOUSING
ON STERN DRIVE
(TYPICAL)
SEAWATER
STRAINERS
PORT
ENGINE
STBD.
ENGINE
AFT
!
CAUTI O N!
SCALDING HAZARD! Never check engine coolant levels whenever the engine is hot or during engine operation.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 17
Controls
STEERING SYSTEM ROUTING
Steering & Shifter/Throttle System
Your boat is equipped with a rack & pinion steering system. The steering system’s shifter/throttle controls are located at the helm.
PORT SHIFTER/
THROTTLE CABLE
Trim Tabs
Trim tabs control the longitudinal and lateral trim of your boat at cruising speeds.
Trim tabs are controlled by two rocker switches at the helm. Before using the trim tab switches, we strongly urge you to read and understand the trim tab operation manual included in your boat’s owner’s packet.
Observe the following:
• Once the best bow cruising trim is reached, use the port or starboard trim switches (one at a time) to correct unequal lateral loading.
Trim tab adjustment should be performed by several short touches to the switch rather than one long one. After each short touch allow about five seconds for the hull to react.
• The trim tab hydraulic fluid reservoir is located in the engine compartment. The fluid level should be checked periodically (at least once a year) and refilled as necessary.
STEERING
CABLE
TYPICAL TRIM TAB
(TRANSOM VIEW)
TO HELM
SHIFTER/THROTTLE
CONTROL
STARBOARD
SHIFTER/THROTTLE
CABLE
TO STEERING
WHEEL AT HELM
TYPICAL TRIM TAB
ROCKER SWITCHES
(LOCATED AT HELM)
!
WARN I NG!
LOSS OF CONTROL HAZARD!
• Improper use of trim tabs may cause loss of control!
• Do not allow anyone unfamiliar with trim tabs to operate them.
• Do not use trim tabs in a following sea as they may cause broaching or other unsafe handling characteristics.
• Do not use trim tabs to compensate for excessive unequal weight distribution.
Bilge
Bilge Pumps
Your boat is equipped with two automatic impeller-type bilge pumps (see illustration on next page) which are used to pump water out of the bilge. Bilge pumps are controlled by automatic bilge pump float switches (autofloat switches) and/or switches at the helm.Bilge pumps are wired directly to the battery so they will normally function even when the boat is completely shut down and left unattended.
NOTI C E
Discharge of oil, oil waste or fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
18 Chapter 2: Components/Systems
Bilge Pump Routing
AFT BILGE PUMP
& FLOAT SWITCH
TO THRU-HULL
FORWARD BILGE PUMP
& FLOAT SWITCH
TO THRU-HULL
Bilge Pump Testing
Bilge pumps should be checked often to verify that they are working properly. To test a bilge pump’s operation, activate the dash-mounted switch and verify that water in the bilge is pumped overboard. If bilge water is present and the pump motor is running but not pumping, inspect the discharge hose for a kink or collapsed area. If no problems are found, check the bilge pump housing for clogging debris as follows:
1.
Remove the power cartridge: a. Lift the tab while rotating the fins counter-clockwise.
b. Lift out the power cartridge.
c. Clear the outer housing of debris.
2.
Reinstall the power cartridge: a. Make sure the “O” ring is properly seated. b. Coat the “O” ring with a light film of vegetable or mineral oil.
c. Align the two cams on either side of the power cartridge with the two slots on the outer housing and press the power cartridge into the housing while twisting clockwise. To ensure proper reinstallation, attempt to twist the fins counter-clockwise without lifting the tab; the cartridge should stay in place.
TYPICAL
BILGE PUMP
COMPONENTS
TAB
“O” RING
FIN
OUTER
HOUSING
LIGHT
FILM
OF OIL
CAM
(TYPICAL)
POWER
CARTRIDGE
SLOT (TYPICAL)
Autofloat Switches
Automatic bilge pumps use electromagnetic float (autofloat) switches to automatically activate the pump whenever water accumulates above a preset level in the bilge. One autofloat switch is mounted next to the bilge pump it activates, and is wired directly to the battery so it will normally function even when the boat is completely shut down and left unattended. Autofloat switches should be tested often for proper operation as follows:
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 19
To test a type “A” float switch:
1.
Lift the float up by turning the plastic float switch insert (where the wires enter the housing) 1/4 turn counter-clockwise. As the float is lifted, the bilge pump should turn on.
If lifting the float does not turn the pump on, check the inline fuse. If the fuse is good but the switch does not work, it may indicate a bad switch or possibly a low battery.
Release the plastic insert to lower the float and return the float switch to auto mode.
DETAILED VIEW
OF PLASTIC
INSERT
To test a type “B” float switch:
1.
Push the float switch test button up to activate the bilge pump.
If the pump does not turn on, check the inline fuse. If the fuse is good but the switch doesn’t work, it may indicate a bad switch or possibly a low battery.
2.
Push the test button all the way down to return the float switch back into the auto mode.
TYPE “A” FLOAT SWITCH OPERATION
FLOAT
FLOAT DOWN:
BILGE PUMP SHOULD BE OFF
FLOAT UP:
BILGE PUMP SHOULD TURN ON
TYPE “B” FLOAT SWITCH OPERATION
FLOAT SWITCH
TEST BUTTON
FLOAT UP - TEST MODE
BILGE PUMP SHOULD TURN ON
FLOAT DOWN - AUTO MODE
BILGE PUMP SHOULD TURN OFF
!
CAUTI O N!
When test is completed on a type “B” float switch, you MUST push the test button all the way
down to the auto position to return the switch back to auto mode!
Fuel System
Carefully read the fuel section of the Owner’s Manual and the engine operation manual, paying special attention to the subject of fuel recommendations. These manuals are provided in your boat’s owner’s packet.
!
WARN I NG!
FIRE, EXPLOSION AND OPEN FLAME HAZARD!
• It is very important that the fuel system be inspected thoroughly the first time it is filled and at each subsequent filling.
• The fueling instructions in the Owner’s Manual and the fuel recommendations in the engine operation manual must be followed.
!
CAUTI O N!
• Avoid the storage or handling of gear near the fuel lines, fittings and tank.
• Diesel option: Air in the diesel supply system can stop an engine or severely restrict performance. If you suspect air in the fuel lines, refer to your engine operation manual for detailed instructions on how to bleed the system.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
20 Chapter 2: Components/Systems
NOTI C E
Discharge of fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities.
Fuel Fill Location
The fuel fill receptacle is located on the starboard side of the aft deck and are marked either “Diesel” or
“GAS”. If you experience difficulty filling the fuel tank, check to see that the fuel fill and vent lines are free of obstructions and kinks.
FUEL FILL RECEPTACLE LOCATION
Fuel Quality
• Refer to your engine manual for fuel grade recommendations.
• Make sure your fuel suppliers are reputable and can be relied upon to furnish clean, high quality fuel.
Once you have found such suppliers, keep your tank as full as possible with their fuel, allowing for expansion due to temperature variations. Then, if you are forced to add to the tank with a potentially poor quality supply, the portion of poor quality fuel will be minimized.
FUEL FILL
FITTING
• Consult your selling dealer or local marina about recommended fuel additives that help prevent fungus or build-up inside the fuel tank.
Fuel Filters & Separators
Fuel filters and separators should be replaced periodically according to the guidelines and instructions detailed in your engine manual, optional generator manual and in any filter literature included in your boat’s owner’s packet.
TYPICAL FUEL TANK FILL AND VENT ROUTINGS
Anti-siphon Valves (Gas Only)
• An anti-siphon valve is an integral part of the fuel line barb fitting on the fuel tank. These valves are spring loaded and are opened by fuel pump vacuum.
• In the unlikely event of a fuel line rupturing, the antisiphon valve is designed to prevent the siphoning of fuel from the tank.
FUEL FILL
FITTING
ON DECK
FUEL TANK AFT
HULLSIDE VENT FITTING
!
WARN I NG!
FIRE/EXPLOSION HAZARD!
• Except in an emergency, never operate the engines without the anti-siphon valve.
• If an engine problem is caused by fuel starvation, check the anti-siphon valve. If the valve is stuck or clogged, shut down the engine and replace it.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Gas Fuel System Routing
Chapter 2: Components/Systems 21
FUEL TANK
FUEL WITHDRAWAL
TO ENGINE (TYPICAL)
PORT
ENGINE
STARBOARD ENGINE
Diesel Fuel System Routing (Option)
FUEL SHUT-OFF VALVES
FUEL
FILTERS
FUEL
WITHDRAWAL
FUEL FILTER/SEPARATOR
(TYPICAL)
AFT
STARBOARD
ENGINE RETURN
ABCDEFG
AFT
STARBOARD
ENGINE INPUT
PORT
ENGINE INPUT
PORT ENGINE RETURN
Freshwater System
Your boat features a pressure-type (demand) freshwater system.
• The water tank fill fitting is located on the starboard deck.
• The water pump’s DC breaker should be turned off whenever the boat is not in use or whenever the water tank is empty.
• The water filter should be inspected and cleaned often.
• When your boat is to be left unattended for long periods of time, pump the water tank dry to prevent stored water from becoming stagnant and distasteful. Should it become necessary to disinfect the freshwater system, ask your dealer about treatments that are available for your boat’s system.
• The water tank can be accessed through the cabin entry steps (after removing the trash can under the top step). It recommended that the water tank be topped off at every opportunity to avoid the possibility of running short of freshwater.
WATER TANK FILL FITTING LOCATION
FRESHWATER TANK
FILL FITTING
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
22 Chapter 2: Components/Systems
Freshwater Water System Routing
= COLD WATER ROUTING
= HOT WATER ROUTING
TO ENTERTAINMENT CENTER FAUCET
WATER
HEATER
HEAD SINK
HEAD
SHOWER
DRAINS
TO BILGE
WATER PUMP
VENT HOSE
WATER
TANK
WATER HOSE
GALLEY SINK
TRANSOM
SHOWER
HULLSIDE VENT
WATER FILL DECK FITTING
Water Heater
• Your boat is equipped with a water heater (located in the utility room). The water heater can be accessed through the hatch at the foot of the aft berth mattress.
• The water heater is connected to the AC power system, therefore, you must verify that the water heater breaker on the AC panel is turned on before water can be heated.
• Read the manufacturer’s instruction manual supplied in your boat’s owner’s packet.
!
CAUTI O N!
WATER HEATER DAMAGE HAZARD!
• Do not energize the AC water heater electrical circuit until the heater is completely filled with water. Even momentary operation in a dry tank will damage the heating elements.
Warranty replacements will not be made on elements or tank damaged in this manner.
• Water heaters should be drained and the power turned off whenever the possibility of freezing exists.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 23
Sink & Shower Drain Systems
• Gray water (water from sinks and showers) above the waterline is gravity drained overboard, while gray water below the waterline is pumped overboard using a sump pump.
• The shower sump pump is located inside the utility room, near the water heater. Access to the sump pump is through the hatch at the foot of the aft berth mattress.
• The shower sump pump is activated by a switch near the shower, just below the sink (see illustration below).
• The sump pump should be periodically cleaned of debris according to the instructions outlined in the bilge pump section of this Supplement.
AFT
SHOWER
SUMP PUMP
SHOWER SUMP PUMP LOCATION
TO
THRU-HULL
STRAINER
SHOWER
DRAIN
SHOWER SUMP PUMP SWITCH LOCATION TRANSOM SHOWER LOCATION
SHOWER SUMP
PUMP SWITCH
SHOWER SUMP
PUMP LABEL
SHOWER
DRAIN
TRANSOM
STORAGE TUB
TRANSOM
SHOWER (INSIDE)
Transom Shower
Your boat is equipped with a freshwater transom shower, located inside the transom storage tub (see drawing above).
Be sure to read the manufacturer’s operating instructions, provided in your boat’s owner’s packet.
Seawater Systems
SEAWATER INTAKE VALVE (SEACOCK)
COMPONENTS (TYPICAL)
Seacocks
A seacock is a valve that is used to manage the intake of seawater through the hull and below the water line. Seacocks are controlled by a 90º lever and are typically used on your boat in the following seawater intake systems: (Optional) generator system, (optional) air conditioning system and marine head (toilet) system. Before using any of these systems, verify that the system’s seacock is open and remains in the open position until the system is shut off.
90 DEG.
SEACOCK
LEVER
HULL
SECTION
SEACOCK (TYPICAL)
SEACOCK GASKET
INTAKE STRAINER
!
CAUTI O N!
SYSTEM DAMAGE HAZARD!
• Before using a seawater intake system, verify that the system’s seacock is in the open position before the system is started and keep the seacock open until the system is shut off.
• Close seacocks whenever the systems will not be used for long periods of time
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
C
(T
24 Chapter 2: Components/Systems
Seawater Strainers
Seawater strainers are used in water pick-up systems to filter incoming seawater. The typical layout is one strainer for each of the following: Optional generator and optional air conditioning system.
Seawater strainers are located near the system’s seawater intake valves (seacocks) and should be checked every time
you use your boat for leaks and/or debris. If debris is found, clean the seawater strainer as follows:
1.
Make sure the component/system that the strainer is connected to is turned off.
2.
Close the intake seacock that sends seawater to the strainer you are about to clean. The seacock must remain closed until the strainer is completely reassembled.
3.
Take apart the seawater strainer.
4.
Remove debris.
5.
Reassemble the seawater strainer.
6.
Open the seacock before turning on the component or system.
!
CAUTI O N!
• FLOODING HAZARD! The intake seacock that sends seawater to the strainer must be
closed before disassembling the seawater strainer to prevent the boat from taking on water through the seawater strainer assembly. Keep the intake seacock closed until the seawater strainer is completely reassembled.
• SYSTEM DAMAGE HAZARD! After reassembling the seawater strainer, verify that the intake seacock is open before activating the component/system.
Air Conditioning & Heating (Option)
Your boat may be equipped with an optional air conditioning & heating system. For complete operating instructions, please read the air conditioner’s user manual, provided in your boat’s owner’s packet.
Both heating and cooling are controlled from the same panel.
• Before operating the air conditioning/heating unit, make sure the breaker on the AC main distribution panel is activated.
• The air conditioning unit’s sump pump system (pump and float switch) can be accessed from under port side of the V-berth mattress. Periodically clean debris out of the sump pump and test the autofloat switch according to the bilge pump and autofloat sections of this Supplement.
• Make sure the air conditioning system’s seawater intake valve (seacock) is open before turning on the air conditioning/heating system.
!
CAUTI O N!
SYSTEM DAMAGE HAZARD! The air conditioning system’s seawater intake seacock must remain open anytime the air conditioner/heater is in use.
Air Conditioning Water Pick-up Routing
AFT
SEAWATER
STRAINER
WATER
PUMP
PVC PIPE
SEAWATER
INTAKE VALVE
(SEACOCK)
TO AIR
CONDITION UNIT
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Air Conditioning Drain Routing
AFT
FROM WATER PUMP
TO AIR CONDITION UNIT
DRAIN TO SUMP
PUMP SYSTEM
Chapter 2: Components/Systems 25
FROM AIR CONDITION
UNIT TO THRU-HULL
FROM SUMP PUMP
TO THRU-HULL
SUMP PUMP SYSTEM
(PUMP, FLOAT SWITCH
& HOLDING TANK)
JUNCTION BOX
AIR CONDITION UNIT
Air Conditioning Duct Routing
HEAD VENT V-BERTH
VENT
AIR
CONDITION
UNIT
AFT BERTH VENT
SALON VENT
JUNCTION BOX
(TYPICAL)
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
26 Chapter 2: Components/Systems
Marine Head System & Waste Tank
WASTE PUMP-OUT FITTING LOCATION
Your boat comes equipped with a marine head (toilet) and waste holding tank system. Be sure to read the manufacturer’s operation and maintenance manual (included in your boat’s owner’s packet).
• The marine head installed on your boat uses seawater to flush waste from the toilet. The seawater intake valve (seacock) is located in the port forward side of the engine room.
• Waste is routed directly from the head to the holding tank.
• The holding tank is plumbed to a fitting on the deck for dockside pump-out and to a macerator pump for pumping waste overboard (where regulations permit). The macerator pump switches are located at the helm. To activate the pump, you must press both of the macerator switches simultaneously.
• You can determine the content level of the holding tank by looking at the tank through the hatch on the cabin entry top step (with the trash can removed). It is advisable to empty the holding tank at every opportunity.
WASTE PUMP-OUT
FITTING ON DECK
• If you are unable to pump water into the bowl, the probable cause is debris in the pump diaphragm. To remedy this, shut off the seawater intake valve (seacock) and dismantle the pump. The pump is generally held together with six screws (the design is simple and the problem will be obvious when the pump body is split open).
• To winterize the head, shut off the intake seacock and pump until the bowl is dry. Remove the drain plug in the base and pump again to remove all of the water. Do not fill the bowl with anti-freeze. The intake seacock should be left closed while the boat is underway or whenever the boat is left moored in the water.
Operating the manual flush marine head:
1.
Open the head’s seawater intake valve (seacock).
2.
Before using the head, pump enough water into the bowl to wet the sides.
3.
After use, pump until the bowl is thoroughly cleaned. Continue pumping a few more times to clean the lines. If excess waste causes the water to rise in the bowl, stop pumping until the water recedes.
NOTI C E
Check with local authorities for regulations regarding the legal use of marine head systems.
Standard Head System Routing
AFT
TO PUMP-OUT
FITTING ON DECK
TO THRU-HULL
SEAWATER INTAKE
VALVE (SEACOCK) HOLDING
TANK VENT
WASTE FROM HEAD
TO WASTE TANK
HEAD
SEAWATER
TO HEAD
MACERATOR
WASTE HOLDING
TANK
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Chapter 2: Components/Systems 27
Macerator Delete Head System (Option)
The macerator delete head system option uses seawater to flush waste from the toilet directly into the waste tank.
The waste tank is plumbed to a receptacle on the deck for dockside pump-out only.
Macerator Delete Routing (Option)
AFT DECK PUMP-OUT
FITTING
SEAWATER INTAKE
VALVE (SEACOCK) HOLDING
TANK VENT
WASTE FROM HEAD
TO WASTE TANK
SEAWATER
INTO HEAD
HEAD
WASTE HOLDING
TANK
Labels
• There are many safety labels that are used throughout your boat to point out potentially hazardous situations.
Always follow the safety label recommendations and immediately contact your dealer if a label becomes damaged or has been accidently removed.
• Not all safety labels affixed to your boat appear in this section.
• Be sure to read the Owner’s Manual and all component and system manuals included in your owner’s packet for other important safety concerns.
AC Panel Label
SHORE POWER
WARNING LABEL
AC PANEL (INSIDE)
VIEW OF GALLEY
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
28 Chapter 2: Components/Systems
Helm Labels
VIEW OF HELM
FOREDECK
WARNING
LABEL
EMERGENCY
SHUT DOWN LABEL
Aft Labels
CARBON MONOXIDE
WARNING LABEL
ENGINE
BLOWER
LABEL
1"
TRIM TAB
WARNING
LABEL
MACERATOR
PUMP LABEL
POTABLE WATER
(FRESHWATER)
LABEL
FUEL FILL WARNING LABEL BOARDING LADDER
WARNING LABEL
US MARINE
LABEL
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
29
Appendix A: Wiring Schematics
Key to Electrical Symbols
Symbol Description
Connection (Node)
No Connection
Battery
Earth Ground: Represents a black conductor that is the same size as the colored conductor
Ammeter
Frequency Meter
Plug
Breaker
Breaker
Fuse
Switch: Single Pole Single Throw (SPST)
Switch: Double Pole Single Throw (DPST)
Symbol Description
Fuel Sender
Incandescent Lamp
Neon Lamp
Diode
12 Volt DC Receptacle
Voltmeter
Motor/Pump
Current Transformer
Solenoid
Gauge
Speaker/Horn/Alarm
Float Switch
Lighted Switch: Single Pole Single Throw (SPST)
Wire Color Key
Color Key
B or BLK
BL or BLU
BR or BRN
DK
GY or GRY
Description
Black
Blue
Brown
Dark
Gray
Color Key
G, GR or GRN
Description Color Key
Green R or RED
LT
O, OR or ORG
Light
Orange
PK Pink
PU, PUR or PPL Purple
Description
Red
T or TAN Tan
W, WH or WHT White
Y or YEL Yellow
NOTI C E
• Wiring diagrams may show optional equipment not installed on all models.
• Some boats may come equipped with silver (-) and copper (+) colored speaker wires or red/black (-) and red/white (+) port speaker wire colors; green/black (-) and green/white
(+) starboard speaker wire colors.
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
30 Appendix A: Wiring Schematics
Dash Connector Harness
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Hull Harness
Appendix A: Wiring Schematics 31
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
32 Appendix A: Wiring Schematics
Hull Harness (Diesel Option)
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Deck Harness
Appendix A: Wiring Schematics 33
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
34 Appendix A: Wiring Schematics
AC Dockside Harness
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Ignition Panel Harness (Gas)
Large Dash Switch Panel Harness
Appendix A: Wiring Schematics 35
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
36
Appendix B: Electrical Routings
Bonding Harness
GENERATOR
EXHAUST
(OPTION)
AIR CONDITION
PICK-UP (OPTION)
BUSS BAR
PORT
ENGINE
BUSS BAR
ZINC PLATE
HEAD PICK-UP
AIR CONDITION
STRAINER (OPTION)
GENERATOR
PICK-UP (OPTION)
GENERATOR
STRAINER
(OPTION)
AIR CONDITION
PANEL (OPTION)
STARBOARD
ENGINE
Aft Deck Harness
BUSS BAR
COURTESY
LIGHTS
OVERHEAD
LIGHTS
RADAR
WING/HORN
COURTESY
LIGHT
STEREO
DASH
HEAD
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Appendix B: Electrical Routings 37
Forward Deck Harness
OVERHEAD
LIGHTS
SPEAKERS
WIPERS
SWITCHES
AC Harness
BATTERY
CHARGER
WATER
HEATER
AIR CONDITION
CONTROL PANEL
(OPTION)
NAVIGATION
LIGHTS
OVERHEAD
LIGHTS
COURTESY
LIGHT
SPOTLIGHT
(OPTION)
ANCHOR WINDLASS
CONTROLS (OPTION)
AIR CONDITION
PANEL (OPTION)
SHORE POWER
POWER INLET
AIR CONDITION
PUMP (OPTION)
HEAD
OUTLET
GALLEY
OUTLET
AIR CONDITION
UNIT (OPTION)
DINETTE OUTLET
AFT BERTH OUTLET
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
38 Appendix B: Electrical Routings
DC Harness
PORT ENGINE
BATTERY
SWITCH
PANEL
BATTERY
CHARGER
SHOWER
SUMP PUMP
HEAD
SWITCHES
REFRIGERATOR
WATER
SWITCH
TILT
PUMP
TRIM PUMP
BILGE PUMP
MACERATOR
TILT
PUMP
STARBOARD
ENGINE
WATER PUMP
FUEL TANK
BILGE PUMP
TRANSDUCER
BLOWER
Positive Battery Cable Harness
AFT BERTH
SWITCHES
DC PANEL
TO DEPTH FINDER
(OPTION) IN DASH
BATTERY
SWITCH PANEL
AIR CONDITION
SUMP PUMP BOX
(OPTION)
PORT
ENGINE
GENERATOR
(OPTION)
STARBOARD
ENGINE
STARBOARD
ENGINE BATTERY
PORT ENGINE
BATTERY
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
DC PANEL
Appendix B: Electrical Routings 39
Negative Battery Cable Harness (Gas)
PORT
ENGINE
STARBOARD
ENGINE
GENERATOR
(OPTION)
STARBOARD
ENGINE BATTERY
BUSS BAR
PORT ENGINE
BATTERY
Negative Battery Cable Harness (Diesel Option)
DC PANEL
PORT
ENGINE
STARBOARD
ENGINE
GENERATOR
(OPTION)
STARBOARD
ENGINE BATTERY
BUSS BAR
DC
PANEL
PORT ENGINE
BATTERY
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
40 Appendix B: Electrical Routings
Head Harness
PLUG
LIGHTS
SHOWER
SUMP PUMP
SWITCH
Windlass Cable Harness (Optional)
UNDERSIDE VIEW OF DECK
= POSITIVE
= NEGATIVE
ANCHOR WINDLASS
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
STBD.
TO BUSS BAR
ON ENGINE
BULKHEAD
TO WINDLASS
BREAKER
Radar Wing Harness
Appendix B: Electrical Routings 41
COURTESY
LIGHTS
HORN
PORT
SPEAKER
NAVIGATION
LIGHT
STARBOARD
SPEAKER
PLUG
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
42
Appendix C: Limited Warranty
Bayliner warrants to the original purchasers of its 2000 and 2001 model boats, purchased from an authorized dealer, operated under normal, noncommercial use that the selling dealer will: (A) Repair any structural hull defect which occurs within five (5) years of the date of delivery; and (B) Repair or replace any parts found to be defective in factory material or workmanship within one (1) year of the date of delivery.
What Is Not Covered
This limited warranty does not apply to:
1.
Engines, drive trains, controls, props, batteries, or other equipment or accessories carrying their own individual warranties;
2.
Engines, parts or accessories not installed by Bayliner;
3.
Plexiglass windscreen breakage; rainwater leakage on runabout models; rainwater leakage through convertible tops; minor gelcoat discoloration, cracks or crazing or air voids;
4.
Hull blisters that form below the waterline;
5.
Normal deterioration, i.e. wear, tear, or corrosion of hardware, vinyl, tops, vinyl and fabric upholstery, plastic, metal, wood, or trim tape;
6.
Any Bayliner boat used for commercial purposes;
7.
Any defect caused by failure of the customer to provide reasonable care and maintenance.
Other Limitations
THERE ARE NO OTHER EXPRESS WARRANTIES ON THIS BOAT. TO THE EXTENT ALLOWED BY LAW:
1.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED
TO THE DURATION OF ONE YEAR.
2.
Neither Bayliner nor the selling dealer shall have any responsibility for loss of use of the boat, loss of time, inconvenience, commercial loss or consequential damages.
3.
Some jurisdictions do not allow limitations on how long any implied warranty lasts, so the above limitation may not apply to you. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your Obligation
In order to comply with regulations, it is essential that your limited warranty registration card be submitted within 30 days of delivery of your boat. Return of the limited warranty registration card is a condition precedent to limited warranty coverage.
Before any warranty work is performed, we require that you contact your dealer to request warranty assistance.
YOU MUST GIVE US WRITTEN NOTICE OF YOUR WARRANTY CLAIM PRIOR TO THE EXPIRATION OF YOUR
LIMITED WARRANTY AND ALLOW US AN OPPORTUNITY TO RESOLVE THE MATTER.
We require that you return your boat, at your expense, to your selling dealer or, if necessary, to the Bayliner factory. You will be responsible for all transportation, haulouts and other expenses incurred in returning the boat for warranty service.
Bayliner Marine Corporation
PO Box 9029
Everett, WA 98206
Phone: 360-435-8957
FAX: 360-403-4235
3055 EL Ciera Sunbridge • Owner’s Manual Supplement
Owner’s Notes
Owner’s Notes
Part Number 1706512
Bayliner • P.O. Box 9029 • Everett, WA 98206 • 360-435-5571
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project