H A N D B O O K
Arcam A65, A75 and P75 amplifi ers
Amplifi cateurs Arcam A65, A75 et P75
Arcam-Verstärker A65, A75 und P75
A65
A75
P75
E n g l i s h
F r a n ç a i s
D e u t s c h
Safety guidelines
Safety instructions
This product is designed and manufactured to meet strict quality and safety standards. However, you should be aware of the following installation and operation precautions:
1. Take heed of warnings and instructions
You should read all the safety and operating instructions before operating this appliance. Retain this handbook for future reference and adhere to all warnings in the handbook or on the appliance.
2. Water and moisture
The presence of electricity near water can be dangerous. Do not use the appliance near water – for example next to a bathtub, washbowl, kitchen sink, in a wet basement or near a swimming pool, etc.
3. Object or liquid entry
Take care that objects do not fall and liquids are not spilled into the enclosure through any openings. Liquid fi lled objects such as vases should not be placed on the equipment.
4. Ventilation
Do not place the equipment on a bed, sofa, rug or similar soft surface, or in an enclosed bookcase or cabinet, since ventilation may be impeded. We recommend a minimum distance of 50mm (2 inches) around the sides and top of the appliance to provide adequate ventilation.
5. Heat
Locate the appliance away from naked fl ames or heat producing equipment such as radiators, stoves or other appliances (including other amplifi ers) that produce heat.
6. Climate
The appliance has been designed for use in moderate climates.
7. Racks and stands
Only use a rack or stand that is recommended for use with audio equipment. If the equipment is on a portable rack it should be moved with great care, to avoid overturning the combination.
8. Cleaning
Unplug the unit from the mains supply before cleaning.
The case should normally only require a wipe with a soft, damp, lint-free cloth. Do not use paint thinners or other chemical solvents for cleaning.
We do not advise the use of furniture cleaning sprays or polishes as they can cause indelible white marks if the unit is subsequently wiped with a damp cloth.
9. Power sources
Only connect the appliance to a power supply of the type described in the operating instructions or as marked on the appliance.
10. Power-cord protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, and the point where they exit from the appliance.
11. Grounding
Ensure that the grounding means of the appliance is not defeated.
12. Power lines
Locate any outdoor antenna/aerial away from power lines.
13. Non-use periods
If the unit has a standby function, a small amount of current will continue to fl ow into the equipment in this mode. Unplug the power cord of the appliance from the outlet if left unused for a long period of time.
14. Abnormal smell
If an abnormal smell or smoke is detected from the appliance, turn the power off immediately and unplug the unit from the wall outlet. Contact your dealer immediately.
15. Servicing
You should not attempt to service the appliance beyond that described in this handbook. All other servicing should be referred to qualifi ed service personnel.
16. Damage requiring service
The appliance should be serviced by qualifi ed service personnel when:
A. the power-supply cord or the plug has been damaged, or
B. objects have fallen, or liquid has spilled into the appliance, or
C. the appliance has been exposed to rain, or
D. the appliance does not appear to operate normally or exhibits a marked change in performance, or
E. the appliance has been dropped or the enclosure damaged.
Safety compliance
This product has been designed to meet the EN60065 international electrical safety standard.
A65/A75/P75
2
Using this handbook
This handbook has been designed to give you all the information you need to install, connect, set up and use the
Arcam A65, A75 and P75 amplifi ers. The remote control handset supplied with the equipment is also described.
It may be that your amplifi er has been set up as part of your system installation by a qualifi ed Arcam dealer. In this case, you may wish to skip the sections of this handbook dealing with installation and setting up the unit. Use the Contents list on this page to guide you to the relevant sections.
Models covered
This handbook covers two integrated amplifi ers:
A65
A75
and one power amplifi er:
P75
These amplifi ers have many features in common.
Both the A65 and A75 have remote controlled input selection and a motorised volume control which can be operated by the
CR-389 remote control handset supplied.
Safety
Safety guidelines are set out on the inside front cover of this handbook.
Many of these items are common sense precautions, but for your own safety, and to ensure that you do not damage the unit, we strongly recommend that you read them.
Contents
Safety guidelines
Safety instructions
Safety compliance
Using this handbook 3
Models covered 3
Safety 3
2
2
2
Installation: A65 and A75
Positioning the unit
Connecting to loudspeakers
Connecting to a power supply
Connecting to other equipment
4
4
4
4
5
Using the amplifi ers
Recording onto tape
Using a remote control
Using the remote control
CR-389 remote control
Installation: P75
Loudspeaker connection
Connecting to other equipment
Connecting to a power supply
Using the power amplifi er
Bi-wiring and bi-amping loudspeakers
Before you start
Bi-wiring your loudspeakers
Bi-amping your system
Technical specifi cations 10
Guarantee 11
9
9
9
9
On-line registration 11
8
8
8
8
8
6
6
6
7
7
A65/A75/P75
3
Installation: A65 and A75
Positioning the unit
Place your amplifi er on a level, fi rm surface.
Avoid placing the unit in direct sunlight or near sources of heat or damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space such as a bookcase or cabinet as both of these will impede air fl ow through the ventilation slots.
Connecting to loudspeakers
Your amplifi er is fi tted with loudspeaker terminals to BFA
(British Federation of Audio) standard specifi cation.
BFA loudspeaker terminals
SP1 DIRECT terminals
3
Are switched off when a headphone jack plug is inserted in the headphone socket co on the front of the amplifi er or, by pressing the
MUTE
button on the remote control handset.
SP2 SWITCHED terminals
4
Are switched off when a headphone jack plug is inserted in the headphone socket co on the front of the amplifi er or, by pressing the
MUTE
button on the remote control handset.
If you want to connect speakers for occasional use (perhaps in another room), connect them to these terminals. They can be turned off easily by releasing the front panel switch cn
.
Volume control settings
It is important to realise that the position of the volume control is not an accurate indication of the power delivered to your loudspeakers. The amplifi er will often deliver its full power long before the volume control reaches its maximum position particularly when listening to heavily recorded compact discs.
However the amplifi er also has to be capable of giving full power output from much lower level sources, such as tuners and cassette decks. Using these sources, the volume control setting may be much higher before distortion (audible overload) sets in.
The terminal will accept spade terminals, bare wires or a
BFA plug. BFA plugs are available from your Arcam dealer. To connect a bare wire or spade terminal unscrew the red (or black) part of the loudspeaker terminal fi rst.
Insert the wire or spade terminal and screw it back up.
CAUTION: Do not over tighten the loudspeaker terminals or use a wrench, pliers, etc., as this could cause damage to the terminals which will not be covered under warranty.
Connect the right hand speaker to the terminals on the back of your amplifi er marked R and the left speaker to the terminals marked L.
Connect your loudspeakers so that the red (positive/+) terminal on each loudspeaker is connected to the red (positive/+) terminal on the amplifi er. Your loudspeaker cables may be marked to show polarity (negative/– and positive/+), if not, then the positive terminal can usually be identifi ed by a ridge or coloured marking.
Now connect your loudspeakers’ black (negative/–) terminals to the black (negative/–) terminals on the amplifi er.
Ensure that no stray strands of inner wires are allowed to touch another cable or the amplifi er’s casing. This can cause a short circuit and damage your amplifi er! Two pairs of speakers may be connected at the same time provided each pair is rated between 8 and 16
Ω. If one or both pairs have an impedance of less than 8
Ω, the combined load on the amplifi er falls below
4
Ω and could cause an overload. If so, the overload protection circuit engages and the amplifi er will not work.
Connecting to a power supply
Wrong plug?
Check that the plug supplied with the unit fi ts your supply and that your mains supply voltage agrees with the voltage setting
(120V or 230V) indicated on the rear panel of the unit.
If your mains supply voltage or mains plug is different, consult your Arcam dealer or Arcam Customer Support on +44
(0)1223 203203.
Mains lead
The appliance is normally supplied with a moulded mains plug already fi tted to the lead. If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Should you require a new mains lead, contact your
Arcam dealer.
Plugging in
Push the plug (IEC line socket) of the power cable supplied with the unit into the socket ( ) in the back of the unit. Make sure it is pushed in fi rmly.
Put the plug on the other end of the cable into your power supply socket and switch the socket on.
A65/A75/P75
4
+
R
–
Arcam A65 or A75 amplifier
+
L
–
Right speaker
+
–
+ –
Left speaker
Wiring your loudspeakers
Connecting to other equipment
All of the input sockets (except
PHONO
) have the same sensitivity and may be used with equipment other than that labelled, if you need to do so.
The use of high quality interconnect cables to and from other hi-fi equipment is recommended to ensure the best sound quality (sonic performance). Ask your Arcam dealer’s advice on cable selection.
AV PROCESSOR/TAPE switch
br
(A75 only)
If you are using the amplifi er with an external processor such as a Dolby Pro Logic or Dolby Digital decoder you should select the AV processor. Connect the left and right audio output sockets of your processor to the corresponding AV/DVD input
8
. Press and hold the
TAPE MONITOR
switch br
for fi ve or more seconds, the amplifi er switches to a fi xed gain. This allows the volume control of your processor to act as a master control and adjust the sound level of the speakers attached to both the A75 and the processor simultaneously. If you then switch back to another input, for example,
CD
, the volume control is switched back in circuit again and the amplifi er functions as normal. You may hear a slight ‘click’ when you switch to another input. This is normal.
WARNING: If the
AV PROCESSOR/TAPE switch is set to
AV PROCESSOR
and the LED is illuminated, do not use the
AV/DVD
socket for any equipment except a processor with its own volume control. Otherwise this could result in a signal being sent to your loudspeakers at high levels which may damage the loudspeakers.
PRE-AMP OUT
5
You will only need to use these sockets if you have a separate power amplifi er. To use your amplifi er as a preamplifi er connect these sockets to the input sockets (
POWER AMP IN
or
PWR AMP IN
) of your power amplifi er. If your power amplifi er is an Arcam P75, P85 or Alpha series you can use it in conjunction with the power amplifi ers in your integrated amplifi er to bi-amplify suitable loudspeakers. See the section ‘Bi-wiring and bi-amping loudspeakers’ for details.
TAPE RECORD OUT
6
Connect these output sockets to the input sockets of your cassette deck (usually labelled
RECORD
).
TAPE PLAY IN
7
Connect these input sockets to the output sockets of your cassette deck (usually labelled
PLAY
). If you do not have a cassette deck you can use this input for other (line level) equipment, such as a CD player, tuner, VCR, etc., but not a turntable (record deck).
AV/DVD
8
VCR
9
TUNER
bk
CD
bl
(
AV
=audio visual,
DVD
=digital versatile disc)
Connect these input sockets to the audio output sockets of the above named equipment.
PHONO
bm
Connect these input sockets to the leads from your turntable
(record deck). The phono stage is suitable for moving magnet
(MM) or high output moving coil (MC) cartridges. If you are using a low output MC cartridge ask your dealer about a suitable external MC preamplifi er.
PHONO/LINE switch
bn
(A75 only)
If you don’t have a record deck and therefore don’t want to use the
PHONO
input socket, press this button in (with the tip of a pencil or a ball point pen) to convert the
PHONO
input to a
LINE
input for equipment such as a CD player, tuner, VCR etc. Press and release the button to use as
PHONO
input again.
Ground terminal
bo
Connect the earth lead (if fi tted) from your turntable or pick-up arm, to this.
A65/A75/P75
5
Using the amplifi ers
Listen selector
bq
Selects the input you wish to listen to. The selected input signal is also sent to the
TAPE RECORD OUT
6 sockets to allow the signal to be recorded, assuming you have a tape deck connected. It is also sent to the
PRE-AMP OUT
sockets
5
.
TAPE
br
Push this switch in to listen to playback from a cassette deck connected to the amplifi er’s
TAPE PLAY IN
sockets
7
.
It also enables you to monitor the recording being made on a
3 head cassette deck.
Note: If the tape switch is in you will be unable to listen to a source selected by the
LISTEN SELECTOR
bq
.
VOLUME
bs
Adjusts the volume level of the loudspeakers, headphone and pre-amplifi er out sockets .
The volume control is motorised and can be controlled remotely with the use of a suitable remote control handset, such as the CR-389 supplied (see the section ‘Using the remote control’ for details).
DIRECT
bt
Push this switch in to bypass the bass, treble and balance controls. This switches these controls out of the circuit
(minimising the signal path) and will generally give a small improvement in sound quality.
BASS
ck
Rotate clockwise to boost the bass response and anticlockwise to cut the bass response. For a fl at response leave in the central ‘click’ position.
TREBLE
cl
Rotate clockwise to boost the treble response and anticlockwise to cut the treble response. For a fl at response leave in the central ‘click’ position.
The range of the tone controls has been deliberately limited to approximately plus or minus 6dB (decibels) at the frequency extremes. This is usually suffi cient to correct small defi ciencies in recordings or speakers.
BALANCE
cm
Rotate clockwise or anti-clockwise to move the position of the stereo image. This may be necessary if it is not possible to sit centrally between the speakers. In normal use leave in the central ‘click’ position.
SP2
cn
Push the button in to select the loudspeakers connected to the SP2
4 speaker terminals. To disconnect the speakers release the switch again.
HEADPHONE socket
co
Accepts headphones rated between 8
Ω and 2kΩ fi tted with a 6.3mm stereo jack plug. If your headphones are fi tted with a different plug, contact your dealer for a suitable adaptor.
Inserting a headphone jack plug automatically mutes (i.e. cuts off) the loudspeakers, but does not mute the
PRE-AMP OUT
sockets
5
.
POWER
cp
Switches the amplifi er on and off.
Power indicator
cq
When the amplifi er is switched on, this will initially glow orange.
After a few seconds it will glow green and a slight click may be heard (as the output muting relay disengages). When the indicator glows orange, the speakers are disconnected and an internal protection circuit is working.
If the indicator glows orange during normal use it may be due to an amplifi er output overload. Switch the amplifi er off and wait for 2 to 3 minutes before switching on again.
If the indicator continues to glow orange, switch the unit off, remove all the speaker cables and switch on again.
If the indicator then goes to green when switched on this indicates a problem with the speakers or speaker cables.
Check the speakers and speaker cables for short circuits before reconnecting them. If the indicator continues to glow orange with no speakers connected, contact your Arcam dealer.
Note that the power indicator glows orange when the amplifi er is muted from the remote control.
Remote control receiver
cr
Make sure nothing is standing in front of the remote control receiver, otherwise messages from the remote control handset cannot be received and it will appear not to work!
Recording onto tape
To record from another piece of hi-fi equipment (an input source), e.g. CD, to a tape deck connected to the amplifi er, fi rst select the
CD
input with the input selector bq
. Set your tape deck into its record mode. Press
PLAY
on your CD player.
The CD signal will now be recorded onto your cassette deck.
If your cassette deck is a 3-head type it is possible to monitor the actual recording on the tape. To do this push the
TAPE
button br
in. Switching this button in/out enables you to do an A/B comparison between the source signal and the recorded signal.
Using a remote control
The A65 and A75 offer remote control of the input selection, volume control and mute via the CR-389 remote handset supplied. It may also be possible to operate these functions with other remote control handsets that use the Philips RC-5 protocol.
If the amplifi ers are muted via remote control, the power indicator glows orange. To cancel the mute function, press
MUTE
again or either of the volume up/down buttons on the remote control handset. If you mislay the handset after muting the amplifi er, turn it off with the
POWER
switch cp
for 20 seconds, then switch it back on again to allow the internal mute system to reset.
A65/A75/P75
6
Using the remote control
CR-389 Remote Control
The CR-389 remote control gives access to all functions available on the front panel. It also has controls to operate
Arcam CD players, AM/FM and DAB tuners.
Tuner controls
These offer basic control of
Arcam tuners.
TUNER
FM DAB
FM
DAB
MENU DISP
1-9 2-10 3-11 4-12
5-13 6-14 7-15 8-16
MODE BAND
ENTER
SP1
SP2
DISP
SEL
Not used with A65/A75
The Power/Standby button does not operate with the A65 and A75 amplifi ers.
Not used with A65/A75
These control features of other amplifi ers in the Arcam range.
Input selection buttons
These operate in the same way as the input selector on the front panel of your integrated amplifi er.
PHONO AUX CD TUNER
AV DVD
AMPLIFIER
VCR TAPE
CD
RPT
PROG DISP
Volume and Mute ( )
Press
+
to increase volume or
–
to decrease the output volume on the amplifi er.
Press to mute the speaker connections and preamp outputs. Both tape outputs and the headphone socket remain active.
Mute is disabled either by pressing again, or by adjusting the volume.
CD controls
These offer basic controls of
Arcam CD players.
CR-389
NOTE: Remember to install the two supplied AAA batteries before trying to use your remote control!
Do not place anything in front of the IR receiver on the left of the A65 or A75, or the remote control may not work.
A65/A75/P75
7
Installation: P75 power amplifi er
The P75 power amplifi er can be used in conjunction with the A65 and A75 integrated amplifi ers (or other Arcam amplifi ers) to bi-amplify loudspeakers that have two pairs of input connections (i.e. are bi-wireable). The P75 can also be used with a pre-amplifi er such as the Arcam 9C or an AV processor or amplifi er with
PRE-AMP OUT
sockets.
Loudspeaker connections
Connect up following the instructions for installing the A65 and
A75 integrated amplifi ers (see page 4).
Connecting to other equipment
PWR AMP IN
5
Connect these sockets to your preamplifi er output sockets.
Alternatively, if you are using an integrated amplifi er (as your pre-amp) such as the A65, A75 or Alpha series amplifi ers, connect the
PWR AMP IN
sockets to the
PRE AMP OUT
sockets on those amplifi ers.
MONO LINK
6
The P75 can be adapted to provide two mono loudspeaker outputs from a single input.
Pull out the U-link
8
supplied and use it to connect the
MONO LINK
sockets
6
together.
Utilising one P75 power amplifi er per loudspeaker will enable you to bi-amplify bi-wireable loudspeakers. This is particularly benefi cial for top quality stereo installations with a separate preamplifi er, or for the left, centre and right channel loudspeakers in a fi ve speaker Dolby Pro Logic™ or Dolby Digital™ system.
Contact your Arcam dealer for more detailed information.
DAISY CHAIN
The P75 is capable of driving further P75 amplifi ers (or any other power amplifi er), to drive more speakers (e.g. those in other rooms or tri-amplifi ed speakers etc). Connect the extra power amplifi er inputs to the
MONO LINK
outputs
6
left to left, right to right with suitable high quality phono to phono cables.
Connecting to a power supply
Connect up following the instructions for installing the A65 and
A75 integrated amplifi ers (page 4).
CIM MODULE
7
The CIM (custom install module) is an optional module that enables you to adjust the gain of the left and right channels of the power amplifi er independently and also to switch the power amplifi er on/off remotely, with a 12 volt trigger. The CIM module would normally be used in a multi-room set up. When a CIM module is fi tted into a power amplifi er, the front panel power switch is disabled.
See your Arcam dealer for further information.
Using the power amplifi er
SP1 DIRECT terminals
3
Are switched off when a headphone jack plug is inserted in the headphone socket bk
on the front of the amplifi er or, by pressing the
MUTE
button ( ) on the remote control handset.
SP2
9
Push the button in to select the loudspeakers connected to the SP2
4
speaker terminals. To disconnect the speakers, release the switch again.
HEADPHONE socket
bk
Accepts headphones rated between 8
Ω and 2kΩ fi tted with a 6.3mm stereo jack plug. If your headphones are fi tted with a different plug contact your dealer for a suitable adaptor.
Inserting a headphone jack plug automatically mutes (i.e. cuts off) the loudspeakers.
POWER
bl
Switches the amplifi er on and off.
Power indicator
bm
This initially glows orange. After a few seconds, the colour changes to green and a slight click may be heard as the output muting relay disengages.
When the indicator glows orange, the speakers are disconnected and an internal protection circuit is working.
If the indicator glows orange during normal use it may be due to an amplifi er output overload. Switch the amplifi er off and wait for 2–3 minutes before switching on again.
If the indicator continues to glow orange, switch the unit off, remove all the speaker cables and switch on again. If the indicator goes green on switching on, there is a problem with the speakers or speaker cables. Check the speakers and speaker cables for short circuits before reconnecting them.
If the indicator continues to glow orange with no speakers connected, contact your Arcam dealer.
A65/A75/P75
8
Bi-wiring and bi-amping loudspeakers
Before you start
WARNING: Do not make any connections to your amplifi er while it is switched on or connected to the mains supply.
Before switching on please check all connections thoroughly, making sure bare wires or cables are not touching the amplifi er in the wrong places (which could cause short circuits) and you have connected positive (+) to positive and negative (–) to negative.
Always ensure that the volume control on your amplifi er is set to minimum before starting these procedures.
Bi-wiring your loudspeakers
Bi-wiring improves the sound of your system because it divides the high and low frequency signal currents into separate speaker cables. This avoids signal distortions arising from the high and low frequency currents interacting with one another within a single cable, as in conventionally wired systems.
You will need:
Speakers – with four input terminals each: these will be marked
HF (High Frequency) and LF (Low Frequency).
Loudspeaker cables – two pairs of cables per loudspeaker
(which may be joined at the amplifi er end if your amplifi er has only one pair of output terminals per channel). Or, a suitably terminated cable set (a loom, probably prepared by your dealer and capable of being used for bi-wiring in one length).
How to bi-wire loudspeakers
1. Remove the terminal links on the rear of your loudspeakers
Bi-amping your system
The performance of your system can be further enhanced over that achieved with bi-wiring, by extending the principle one stage further to include separate amplifi cation for the low and high frequency drive units in each loudspeaker enclosure.
Connect the amplifi er to the high frequency (HF) terminals and connect the power amplifi er to the low frequency (LF) terminals.
You will need:
Speakers – with four input terminals each (as with bi-wiring): these will be marked HF (High Frequency) and LF (Low
Frequency).
Two amplifi ers – one of these would be the A65 or A75 and the other an Arcam power amplifi er (e.g. P75).
Loudspeaker cables – one pair of cables per loudspeaker or a suitably terminated cable set (a loom, probably prepared by your dealer and capable of being used for bi-amping in one length).
Interconnect cables – one pair of high quality interconnect cables.
How to set up a bi-amped system
1. Remove the terminal links on the rear of your loudspeakers.
WARNING: This step is essential or damage to your amplifi er may result which is not covered under warranty.
2. Connect the cables as shown in the diagram below, ensuring correct polarity at all times.
3. Use the interconnect cables to connect the AUDIO PRE-
OUT sockets of the A65 or A75 to the corresponding
PWR AMP IN sockets of the power amplifi er.
WARNING: This step is essential or damage to your amplifi er may result which is not covered under warranty.
2. Connect the cables as shown in the diagram below, ensuring correct polarity at all times.
+
R
–
Arcam A65 or A75 amplifier
+
L
–
+
R
–
Arcam A65 or A75 amplifier
+
L
–
Right speaker
+
–
HF
+
LF
–
–
+
HF
–
+
LF
–
Left speaker
+
+
HF
LF
–
Right
–
speaker
+
+
HF
LF
–
Left
–
speaker
+ – +
R
Arcam P75 power amplifier
L
–
Bi-wiring using one set of connections on amplifi er Recommended bi-amping confi guration
A65/A75/P75
9
Technical specifi cations
Output power (20Hz–20kHz)
8
Ω, continuous
8
Ω, 1 channel, 1KHz
4
Ω, 1 channel, 1KHz
Harmonic Distortion
Rated output into 8
Ω at 1kHz
Peak current rating
L/R Crosstalk
Input sensitivity for rated power output
Frequency response ± 0.25dB
Physical
Dimensions W x D x H
Weight net
Weight packed
Supplied accessories
E&OE
A65
430 x 330 x 85mm
5.4kg
6.9kg
Mains lead
CR-389 remote
2 x AAA batteries
A75
430 x 330 x 85mm
5.6kg
7.1kg
Mains lead
CR-389 remote
2 x AAA batteries
P75
40W
50W
80W
50W
60W
90W
50W
60W
90W
0.01%
±15A
–68dB
250mV
0.01%
±15A
–68dB
260mV
0.005%
±15A
–90dB
540mV
20Hz–20kHz 20Hz–20kHz 20Hz–20kHz
Inputs
Line inputs:
Noise (CCIR) ref. rated power
Input impedance
AV/DVD (Processor Mode):
Input impedance
Input sensitivity
Power Amplifi er:
Input impedance
Phono input:
Noise (CCIR) ref. rated power
Input sensitivity
Input impedance
Overload margin
–100dB
12k
Ω 12kΩ 100kΩ
N/A
N/A
N/A
–100dB –110dB
12k
Ω N/A
540mV N/A
N/A 100k
Ω
–75dB –76dB N/A
1.9mV 2.0mV N/A
47k
Ω 47kΩ N/A
30dB 30dB N/A
Outputs
Pre-amplifi er output:
Nominal output level 510mV 540mV N/A
Maximum output level
Output impedance
8V 8V N/A
<3
Ω <3Ω N/A
Tape output:
Output impedance <3
Ω <3Ω N/A
Headphones:
Maximum output level into 600
Ω 40mW
40mW
Output impedance 80
Ω 80Ω 80Ω
Mains voltage 230V ± 10% 230V ± 10% 230V ± 10%
Power consumption (max)
115V ± 10%
370VA
115V ± 10%
400VA
115V ± 10%
400VA
430 x 330 x 85mm
5.6kg
7.1kg
Mains lead
Continual improvement policy
Arcam has a policy of continual improvement for its products.
This means that designs and specifi cations are subject to change without notice.
NOTE: All specifi cation values are typical unless otherwise stated.
A65/A75/P75
10
