AVENTOS HF Wood/wide aluminum frame door application
Lift mechanism set
▀
▀
Lift mechanism (qty 2)
#7 x 35 mm (1-3/8”) wood screw (qty 8)
Power factor
85 - 230 (1 lift mechanism req.)
231 - 470
471 - 880
780 - 1440
1401 - 2300 (3 lift mechanisms req.)
Part no.
20F2200.N5
20F2200.N5
20F2500.N5
20F2800.N5
20F2800.N5
Cover set
▀
▀
▀
Right and left cover plate
Non-handed cover cap (qty 2)
Colors: Light Gray, Dark Gray and Silk White
Cover set
Part no.
20F8020.NA
Telescopic arm set
▀
479
558
686
889
Telescopic arm (qty 2)
Cabinet heights
(18-7/8") -
(22") -
(27") -
(35") -
686
889
558
(27")
(35")
1067
(22")
(42")
Part no.
20F3200.01
20F3500.01
20F3800.01
20F3900.01
Mounting plate with bracket set
▀
▀
Left and right mounting plate with bracket
For large overlay five-piece doors
Wood or wide alum door hardware set
▀
▀
▀
▀
▀
▀
CLIP top 120° hinge (qty 2)
COMPACT 33° hinge (qty 2)
CLIP top bottom door hinge (qty 2)
COMPACT mounting plate (qty 2)
Face frame adapter (qty 4)
Telescopic arm mounting plate (qty 2)
NOTE: Three hinges and mounting plates required for cabinet widths over 1219 (48").
Part no.
Hardware set 78Z5530TA8
Inst. screw for wood doors
Inst. screw for wide alum doors
606N or 606P
7072A Mounting plate w/ bracket set
Part no.
175H3F00
Dimensions in millimeters (inch equivalents as noted) © 2021
1
Assembly
1 Locating pin locations
Frameless
Ø5
192 37
WARNING
Risk of injury from spring-loaded arm
▀
▀
Do not push arm assembly down or leave in the down position.
Remove mechanism before installing or removing cabinet.
Top door height
(TDH)
231 to 271
272 to 531
Y
TDH x .6 - 28 + TR
TDH x .6 - 57 + TR
TR = Top reveal
TDH = Top door height
Face frame
Ø
5
192 37
Top door height
(TDH)
231
272 to to
271
531
Y
TDH x .6 - 28 + TR
TDH x .6 - 57 + TR
TR = Top reveal
TDH = Top door height
NOTE: Face frame cabinets must be blocked out flush with the frame or use face frame mounting bracket 20F6001.
Universal individual template is available for pre-boring holes for locating pins.
2 Subject to technical modifications without notice. © 2021
Part no.
65.1051.02
Assembly
2 Attaching the lift mechanism
Align the two locating pins on the lift mechanism with the two Ø5 x 5 holes bored in the side of cabinet, and attach the mechanism with the five wood screws provided.
min 5
5
#7 x 35 mm (1-3/8") wood screws (qty 4)
3 Attach the telescopic arms
Attach telescopic arms by clipping them on in the fully upright position.
WARNING: Risk of injury from spring loaded arm.
Dimensions in millimeters (inch equivalents as noted) © 2021
3
Assembly
4 Small overlay top door hinge planning CLIP top hinges
overlay
B
12.7
Overlay table
13* 14 15 16 17
3 3 4 5
B Bore distance
* Bore at 3 then adjust 1
6
5 Large overlay top door hinge planning COMPACT hinges
CLIP top hinge
Mounting plate
Part no.
70T5580.TL
175H6000
1/2"
Overlay table
1-1/4”
3
Bore distance
COMPACT hinge
Mounting plate
Part no.
32.4630
130.1130.02
4 Subject to technical modifications without notice. © 2021
Assembly
6 Bottom door hinge planning
Reveal table
6 5 4 3
3 4 5 6
B Bore distance
12.7
7a Attaching the telescopic arm mounting plates
CLIP top hinge
Mounting plate
Part no.
78Z5530T
175H6000
Top door height (TDH)
231
272
to
to
271
531
X
TDH x .5 + 70
TDH x .5 + 47
NOTE: For five-piece door mounting specifications, see page 6.
17
12.5
+ Overlay
Telescopic arm mounting plate
Part no.
175H3100
Dimensions in millimeters (inch equivalents as noted) © 2021
5
Assembly
7b Attaching the telescopic arm mounting plate with bracket for five-piece doors
Standard mounting plate works.
ü
12.5
more than
6
Standard mounting plate does not work.
12.5
less than
6
Use mounting plate with bracket when panel is < 6 from screw.
ü
12.5
19
Telescopic arm mounting plate with bracket
6 Subject to technical modifications without notice. © 2021
Part no.
175H3F00
Assembly
8 Attach the top door to the cabinet
9 Attach the bottom door
Attach bottom door to the top door and attach the telescopic arms.
1 a b
Dimensions in millimeters (inch equivalents as noted) © 2021
7
Assembly
10 Adjust tension of the mechanism
1. Close and flush doors to cabinet. Open and close door to test closing force.
2. Open door and adjust tension screws on both lift mechanisms with a power drill. Test door again and repeat until desired function is achieved.
Tension adjustment should be the same on both lift mechanisms.
1 2
Use #2x2 POZI bit
11 Finalizing the door adjustments
1. Adjust each top door hinge and mounting plate to properly align the top door to the cabinet.
2. Adjust each bottom door hinge and mounting plate to properly align doors to the cabinet and to the top door.
1 2
± 3 mm ± 2 mm + 3/- 2 mm ± 2.5 mm ± 2 mm ± 2 mm
NOTE: Although not illustrated here, telescopic arm mounting plates can also be adjusted horizontally ± 2 mm if needed.
8 Subject to technical modifications without notice. © 2021
Assembly
12 Adjust and lock telescopic arms
1. Close and flush doors to cabinet. While pressing on the top door, pull the bottom door open one inch.
2. Slightly open door and lock the telescopic arms into position using the levers as shown.
1
2
Open door enough to lock levers.
13 Attach covers
Attach the left and right cover plates to each lift mechanism.
Dimensions in millimeters (inch equivalents as noted) © 2021
9
Removal
1
Remove covers
Remove left and right cover plates.
WARNING
Risk of injury from spring-loaded arm
▀
▀
Do not push arm assembly down or leave in the down position.
Remove mechanism before installing or removing cabinet.
2 Detaching the telescopic arms
Warning: Risk of injury from spring-loaded telescopic arm!
Maintain control of telescopic arm while releasing the CLIP mechanism.
Release both arms and gently rest the top door on the loose arms. The tension will hold the doors up for the next step.
10 Subject to technical modifications without notice. © 2021
Removal
3 Removing the doors
1 1. Hold the bottom door while unclipping the bottom hinges.
2
2. Hold the top door while detaching the top hinges. Simply unclip them if using the CLIP top hinges or loosen them if using COMPACT.
4 Removing the telescopic arms
Using a screwdriver, depress the release tabs to remove telescopic arms.
If transporting the cabinet to the jobsite, stop here. Lift mechanisms stay inside the cabinet for easy transport.
Dimensions in millimeters (inch equivalents as noted) © 2021
11
Other information
Door clearance above cabinet.
TDH
Blum, Inc.
800-438-6788 [email protected]
blum.com
Z = TDH x .44 + 38
INST-AVT07.21
1 /
2
.5
13
17 /
32
.531
13.5
9 /
16
.563
19 /
32
.594
5
21
/
8
.625
/
32
.656
14
15
16
17
11 /
16
.688
17.5
23 /
32
.719
18
3
25
/
4
.75
/
32
.781
19
20
9.5
10
11
12
6
7
8
9
Inch
1 /
32
.031
1 /
16
.063
3 /
32
.094
5
1 /
8
/
32
.125
.156
3 /
16
1 /
4
.188
7 /
32
.219
.25
9 /
32
.281
5 /
16
.313
11 /
32
.344
3 /
8
.375
13 /
32
.406
7 /
16
.438
15 /
32
.469
5
5.5
3
4 mm
1
1.5
2
13 /
16
.813
20.5
27 /
32
.844
21
7
29
/
8
.875
/
32
.906
22
23
15 /
16
.938
24
31 /
32
.969
24.5
1 1 25.4
