AVENTOS HS Narrow aluminum frame door application
Lift mechanism set
▀
▀
Lift mechanism (qty 2)
#7 x 35 mm (1-3/8”) wood screw (qty 10)
20S2A00.N5
20S2D00.N5
20S2G00.N5
20S2B00.N5
20S2E00.N5
20S2H00.N5
Part no.
20S2C00.N5
20S2F00.N5
20S2I00.N5
Cover set
▀
▀
▀
Right and left cover plate
Non-handed cover caps (qty 2)
Colors: Light Gray, Dark Gray and Silk White
Cover set
Part no.
20S8020.NA
Arm assembly set
▀
▀
Right and left arm assembly
Stabilizer rod cover cap (qty 2)
Arm assembly set
Part no.
20S3500.06
Round stabilizer rod
▀
▀
Aluminum rod length 1061 (41-3/4"), cut to size
Length = interior cabinet opening minus 129 (5-1/16")
Round stabilizer rod
Part no.
20Q1061UN
NOTE: For cabinets wider than 48" two stabilizer rods and a stabilizer rod connector set required.
Narrow aluminum hardware set
▀
▀
Arm assembly mounting plate (qty 2)
699.110 — Aluminum screw for narrow aluminum lever arm mounting plate (qty 8)
Part no.
Narrow aluminum hardware set 20S4200A
Dimensions in millimeters (inch equivalents as noted) © 2021
1
Assembly
WARNING
Risk of injury from spring-loaded arm
▀
▀
Do not push arm assembly down or leave in the down position.
Remove mechanism before installing or removing cabinet.
1 Locating pin locations and minimum depth
Universal individual template is available for pre-boring holes for locating pins.
Part no.
65.1051.02
2 Attaching the lift mechanism
Align the two locating pins on the lift mechanism with the two Ø5 x 5 holes bored in the side of cabinet, and attach the mechanism with the five wood screws provided.
5 min.
Ø5
2 Subject to technical modifications without notice. © 2021
#7 x 35 mm (1-3/8") wood screws (qty 5)
Assembly
3 Attaching the arm assembly a b
1
1
2
2 c Before starting, see safety note on page 2.
a. Find the right and left arm assemblies and match them to the correct side of the cabinet. b. Attach the arm assembly to the lift mechanism as shown.
c. Lift up on the arm assembly to lock into place.
Risk of injury from spring loaded arm.
4 Attaching the stabilizer rod
Cut the stabilizer rod to fit the cabinet. Length = Interior cabinet opening minus 129 (5-1/6")
After cutting the rod to size follow steps 1, 2, and 3 below.
1 2 3
1
2
Slide the stabilizer arm cover caps onto the rod.
Attach the stabilizer rod to spring loaded arm assembly.
3 Slide stabilizer arm cover caps over rod on each end.
Dimensions in millimeters (inch equivalents as noted) © 2021
3
Assembly
5a Mounting plate position
Attach the mounting plate to the door.
+ Ov
5b Planning narrow alum. frames
15 to 19
12.5
+ Ov 12.5 + Overlay overlay
Minimum 5 side reveal when adjacent to wall.
NOTE: All four screws must be installed.
NOTE: When changing material thickness, adjust assembly dimensions.
6 Attaching the door
Attach the door using the CLIP mechanism to the arm assembly.
4 Subject to technical modifications without notice. © 2021
Assembly
7 Adjusting the lift mechanism tension
Use a screw gun and the #2 x 2 POZI driver bit to adjust the lift mechanism to the desired tension.
8 Adjusting the door
Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments.
9 Attach covers
Place the left and right cover plates over the appropriate lift mechanisms and snap them in place.
3 2 1
1 mm
2 mm
3 mm
Dimensions in millimeters (inch equivalents as noted) © 2021
5
Removal
WARNING
Risk of injury from spring-loaded arm
▀
▀
Do not push arm assembly down or leave in the down position.
Remove mechanism before installing or removing cabinet.
1 Removing the door
Open the door. Use a screwdriver to disengage the CLIP mechanism of the arm assembly from the mounting plate.
2 Remove the covers
Remove the left and right cover plates.
6 Subject to technical modifications without notice. © 2021
Removal
3 Remove the stabilizer rod
Pull back the stabilizer rod cover caps and loosen the locking screw on each end of the stabilizer rod. Remove the Stabilizer rod from the cabinet.
4 Removing the arm assembly a Use a screwdriver to disengage the arm assembly as shown. b Remove arm assembly from mechanism.
Cabinet is now ready for transport.
a b
Dimensions in millimeters (inch equivalents as noted) © 2021
7
Other information
Frameless door protrusion for common cabinet heights.
350
600
800
96
227
460
646
Blum, Inc.
800-438-6788 [email protected]
blum.com
INST-AVT07.21
Inch
1 /
32
.031
1 /
16
.063
3 /
32
.094
1 /
8
.125
5
3
/
32
/
16
.156
.188
7 /
32
.219
1 /
4
.25
9 /
32
.281
5 /
16
.313
11 /
32
.344
3 /
8
.375
13 /
32
.406
7 /
16
.438
15 /
32
.469
1 /
2
.5
19
5
/
32
.594
/
8
.625
12
13
17 /
32
.531
13.5
9 /
16
.563
14
15
16
21 /
32
.656
17
11 /
16
.688
17.5
23
3
/
32
.719
/
4
.75
18
19
9
9.5
10
11
5.5
6
7
8
25 /
32
.781
20
13 /
16
.813
20.5
27 /
32
.844
7 /
8
.875
29
15
/
32
.906
/
16
.938
21
22
23
24
31 /
32
.969
24.5
1 1 25.4
4
5
2
3 mm
1
1.5
