Allen-Bradley MicroLogix 1500 1764 Programmable Controllers User Manual

Allen-Bradley
MicroLogix™ 1500
Programmable
Controllers
(Bulletin 1764 Controllers)
User
Manual
Important User Information
Because of the variety of uses for the products described in this publication, those
responsible for the application and use of this control equipment must satisfy
themselves that all necessary steps have been taken to assure that each application and
use meets all performance and safety requirements, including any applicable laws,
regulations, codes and standards.
The illustrations, charts, sample programs and layout examples shown in this guide
are intended solely for purposes of example. Since there are many variables and
requirements associated with any particular installation, Allen-Bradley does not
assume responsibility or liability (to include intellectual property liability) for actual
use based upon the examples shown in or included with this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation
and Maintenance of Solid-State Control (available from your local Allen-Bradley
office), describes some important differences between solid-state equipment and
electromechanical devices that should be taken into consideration when applying
products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in whole or part,
without written permission of Allen-Bradley Company, Inc., is prohibited.
Throughout this manual we use notes to make you aware of safety considerations:
!
ATTENTION: Identifies information about practices or
circumstances that can lead to personal injury or death, property
damage or economic loss.
Attention statements help you to:
•
identify a hazard
•
avoid a hazard
•
recognize the consequences
Note:
Identifies information that is critical for successful application and
understanding of the product.
MicroLogix, Compact, SLC, DTAM Micro, PanelView are trademarks of Rockwell Automation.
RSLogix 500 is a trademark of Rockwell Software, Inc.
Windows is a trademark of MicroSoft Corporation.
Belden is a trademark of Belden, Inc.
Preface
Preface
Read this preface to familiarize yourself with the rest of the manual. It provides
information concerning:
•
who should use this manual
•
the purpose of this manual
•
related documentation
•
conventions used in this manual
•
Allen-Bradley support
Who Should Use this Manual
Use this manual if you are responsible for designing, installing, programming, or
troubleshooting control systems that use MicroLogix 1500 controllers.
You should have a basic understanding of electrical circuitry and familiarity with
relay logic. If you do not, obtain the proper training before using this product.
Purpose of this Manual
This manual is a reference guide for MicroLogix 1500 controllers. It describes the
procedures you use to install, wire, program, and troubleshoot your controller. This
manual:
•
explains how to install and wire your controllers
•
gives you an overview of the MicroLogix 1500 controller system
•
provides the instruction set for the MicroLogix 1500 controllers
•
contains application examples to show the instruction set in use
Refer to your programming software user documentation for more information on
programming your MicroLogix 1500 controller.
P-1
MicroLogix 1500 Programmable Controllers User Manual
Related Documentation
The following documents contain additional information concerning Allen-Bradley
products. To obtain a copy, contact your local Allen-Bradley office or distributor.
For
Read this Document
Document
Number
Information on understanding and applying micro
controllers.
MicroMentor
Information on mounting and wiring the MicroLogix 1500
Base Units, including a mounting template for easy
installation
MicroLogix 1500 Programmable
Controllers Installation Instructions
1764-5.1
A description on how to install and connect an AIC+. This
manual also contains information on network wiring.
Advanced Interface Converter
(AIC+) User Manual
1761-6.4
Information on how to install, configure, and commission a
DNI
DeviceNet™ Interface User Manual
1761-6.5
1761-MMB
Information on DF1 open protocol.
DF1 Protocol and Command Set
Reference Manual
1770-6.5.16
In-depth information on grounding and wiring Allen-Bradley
programmable controllers
Allen-Bradley Programmable
Controller Grounding and Wiring
Guidelines
1770-4.1
A description of important differences between solid-state
programmable controller products and hard-wired
electromechanical devices
Application Considerations for SolidState Controls
SGI-1.1
An article on wire sizes and types for grounding electrical
equipment
National Electrical Code - Published by the National
Fire Protection Association of Boston, MA.
A complete listing of current documentation, including
ordering instructions. Also indicates whether the documents
are available on CD-ROM or in multi-languages.
Allen-Bradley Publication Index
SD499
Allen-Bradley Industrial Automation
Glossary
AG-7.1
A glossary of industrial automation terms and abbreviations
P-2
Preface
Common Techniques Used in this Manual
The following conventions are used throughout this manual:
•
Bulleted lists such as this one provide information, not procedural steps.
•
Numbered lists provide sequential steps or hierarchical information.
•
Italic type is used for emphasis.
Allen-Bradley Support
Allen-Bradley offers support services worldwide, with over 75 Sales/Support Offices,
512 authorized Distributors and 260 authorized Systems Integrators located
throughout the United States alone, plus Allen-Bradley representatives in every major
country in the world.
Local Product Support
Contact your local Allen-Bradley representative for:
•
sales and order support
•
product technical training
•
warranty support
•
support service agreements
Technical Product Assistance
If you need to contact Allen-Bradley for technical assistance, please review the
information in the Troubleshooting appendix first. Then call your local Allen-Bradley
representative.
P-3
MicroLogix 1500 Programmable Controllers User Manual
Your Questions or Comments on this Manual
If you find a problem with this manual, or you have any suggestions for how this
manual could be made more useful to you, please contact us at the address below:
Allen-Bradley Company, Inc.
Control and Information Group
Technical Communication, Dept. A602V
P.O. Box 2086
Milwaukee, WI 53201-2086
or visit our internet page at:
http://www.ab.com/micrologix
P-4
Table of Contents
Table of Contents
1
Hardware Overview
Hardware Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Component Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Communication Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
2
Installing Your Controller
Agency Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Compliance to European Union Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
General Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Power Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Preventing Excessive Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Master Control Relay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Base Unit Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Controller Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Mounting the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Installing Controller Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
3
Wiring Your Controller
Wire Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Using Surge Suppressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Grounding the Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Sinking and Sourcing Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Controller I/O Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
4
Connecting the System
Default Communication Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Using the Communications Toggle Push Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Connecting to the RS-232 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Connecting to a DH485 Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Connecting the AIC+. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
DeviceNet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
toc-i
MicroLogix 1500 Programmable Controllers User Manual
5
Using Inputs and Outputs
Embedded I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Expansion I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
I/O Forcing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Input Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
Latching Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
6
Controller Memory and File Types
Controller Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Data Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
Protecting Data Files During Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9
Clearing the Controller Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10
Allow Future Access Setting (OEM Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11
Function Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
7
Using Trim Pots and the Data Access Tool (DAT)
Trim Pot Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Data Access Tool (DAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
DAT Keypad and Indicator Light Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
Power-Up Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5
DAT Function File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-6
F1 and F2 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-13
Working Screen Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-14
Non-Existent Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-14
Controller Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-14
Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-15
8
Using Real Time Clock and Memory Modules
Real Time Clock Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
Memory Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4
9
Using the High Speed Counter
High Speed Counter (HSC) Function File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2
High Speed Counter Function File Sub-Elements Summary . . . . . . . . . . . . . . . . . . . . . .9-4
HSC Function File Sub-Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-5
HSL - High Speed Counter Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-29
RAC - Reset Accumulated Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-31
toc-ii
10
Using High Speed Outputs
PTO - Pulse Train Output Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Pulse Train Output Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Pulse Train Outputs (PTO) Function File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
Pulse Train Output Function File Sub-Elements Summary . . . . . . . . . . . . . . . . . . . . . 10-7
PWM - Pulse Width Modulation Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20
PWM Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20
Pulse Width Modulated (PWM) Function File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-21
Pulse Width Modulated Function File Elements Summary . . . . . . . . . . . . . . . . . . . . 10-22
11
Programming Instructions Overview
Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Using the Instruction Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
12
Relay-Type (Bit) Instructions
XIC - Examine if Closed, XIO - Examine if Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
OTE - Output Energize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4
OTL - Output Latch, OTU - Output Unlatch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5
ONS - One Shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
OSR - One Shot Rising, OSF - One Shot Falling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
13
Timer and Counter Instructions
Timer Instructions Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
TON - Timer, On-Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
TOF - Timer, Off-Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
RTO - Retentive Timer On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6
CTU - Count Up, CTD - Count Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-10
RES - Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-11
14
Compare Instructions
Using the Compare Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
EQU - Equal, NEQ - Not Equal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
GRT - Greater Than, LES - Less Than . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
GEQ - Greater Than or Equal To, LEQ - Less Than or Equal To. . . . . . . . . . . . . . . . . . . .5
MEQ - Mask Compare for Equal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
LIM - Limit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
toc-iii
MicroLogix 1500 Programmable Controllers User Manual
15
Math Instructions
Using the Math Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-2
Updates to Math Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-3
ADD - Add, SUB - Subtract. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-4
MUL - Multiply, DIV - Divide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-5
NEG - Negate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 -6
CLR - Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-6
SCL - Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-7
SCP - Scale with Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-8
SQR - Square Root . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-10
16
Conversion Instructions
Using Decode and Encode Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-2
DCD - Decode 4 to 1-of-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-3
ENC - Encode 1-of-16 to 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-4
FRD - Convert from Binary Coded Decimal (BCD) . . . . . . . . . . . . . . . . . . . . . . . . . . .16-6
TOD - Convert to Binary Coded Decimal (BCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-10
17
Logical Instructions
Using Logical Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1
Updates to Math Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-2
AND - Bit-Wise AND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-3
OR - Logical OR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-4
XOR - Exclusive OR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-5
NOT - Logical NOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-6
18
Move Instructions
MOV - Move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-2
MVM - Masked Move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-4
19
File Instructions
COP - Copy File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-2
FLL - Fill File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-3
BSL - Bit Shift Left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-5
BSR - Bit Shift Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-7
FFL - First In, First Out (FIFO) Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-9
FFU - First In, First Out (FIFO) Unload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-12
LFL - Last In, First Out (LIFO) Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-15
LFU - Last In, First Out (LIFO) Unload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-18
toc-iv
20
Sequencer Instructions
SQC- Sequencer Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-2
SQO- Sequencer Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-6
SQL - Sequencer Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-10
21
Program Control Instructions
JMP - Jump to Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-2
LBL - Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-2
JSR - Jump to Subroutine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-3
SBR - Subroutine Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-3
RET - Return from Subroutine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4
SUS - Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4
TND - Temporary End. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-5
END - Program End. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-5
MCR - Master Control Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-6
22
Input and Output Instructions
IIM - Immediate Input with Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-2
IOM - Immediate Output with Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4
REF- I/O Refresh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-6
23
Using Interrupts
Information About Using Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-1
User Interrupt Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7
INT - Interrupt Subroutine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7
STS - Selectable Timed Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-8
UID - User Interrupt Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-9
UIE - User Interrupt Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-10
UIF - User Interrupt Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-12
Using the Selectable Timed Interrupt (STI) Function File . . . . . . . . . . . . . . . . . . . . . 23-13
Using the Event Input Interrupt (EII) Function File . . . . . . . . . . . . . . . . . . . . . . . . . . 23-19
24
Process Control Instruction
The PID Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-1
The PID Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2
PD Data File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-3
Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-5
Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-7
Tuning Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-10
Runtime Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-19
Analog I/O Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-21
Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-22
toc-v
MicroLogix 1500 Programmable Controllers User Manual
25
Communications Instructions
MicroLogix 1500 Messaging Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-2
Remote Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-14
MSG Instruction Error Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-18
Timing Diagram for MicroLogix 1500 MSG Instruction . . . . . . . . . . . . . . . . . . . . . .25-21
Service Communications (SVC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-24
Examples: Ladder Logic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-27
Using Local Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-28
Using Remote Messaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-34
Example 2 - Passthru via DH485 Channel 0 of the SLC 5/04 Processor. . . . . . . . . . .25-37
Example - Passthu using Two 1785-KA5s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-40
A
Specifications
Controller Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9
Compact I/O Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Transistor Output Transient Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
B
Replacement Parts
MicroLogix 1500 Replacement Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lithium Battery (1747-BA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Terminal Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C
B-1
B-2
B-6
B-8
Troubleshooting Your System
Understanding the Controller LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Controller Error Recovery Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Identifying Controller Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Calling Allen-Bradley for Assistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-14
D
Understanding the Communication Protocols
RS-232 Communication Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
DF1 Full-Duplex Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
DF1 Half-Duplex Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
DH485 Communication Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-10
E
System Loading and Heat Dissipation
System Loading Limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
System Loading Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-4
Calculating Heat Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6
toc-vi
F
Memory Usage and Instruction Execution Time
Programming Instructions Memory Usage and Execution Time . . . . . . . . . . . . . . . . . . F-1
Scan Time Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-8
G
System Status File
Status File Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-1
Status File Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-3
Glossary
Index
toc-vii
MicroLogix 1500 Programmable Controllers User Manual
toc-viii
Hardware Overview
1
Hardware Overview
Hardware Overview
The MicroLogix 1500 programmable controller contains a power supply, input
circuits, output circuits, and a processor. The controller is available in 24 I/O and
28 I/O configurations.
The hardware features of the controller are:
1
10
2
RUN
REM
PROG
3
12
4
5
11
10 9 8 1 7
Feature
Description
Feature
6
Description
1
Removable Terminal Blocks
7
Memory Module/Real-Time Clock1
2
Interface to Expansion I/O, Removable
ESD Barrier
8
Replacement Battery1
3
Input LEDs
9
Battery
4
Output LEDs
10
Terminal Doors and Label
5
Communication Port
11
Data Access Tool1
6
Status LEDs
12
Mode Switch, Trim Pots
1.Optional.
1-1
MicroLogix 1500 Programmable Controllers User Manual
Component Descriptions
A controller is composed of a standard processor (1764-LSP) and one of the base
units listed below. The FET transistor and relay outputs are available on the
1764-28BXB base only.
Base Units
Catalog Number
1-2
Base Unit I/O and Power Supply
1764-24AWA
Twelve 120V ac inputs, twelve relay outputs and 120/240V ac power supply
1764-24BWA
Twelve 24V dc inputs, twelve relay outputs and 120/240V ac power supply
1764-28BXB
Sixteen 24V dc inputs, six FET and six relay outputs and 24V dc power supply
Hardware Overview
Processor (Catalog Number 1764-LSP)
Data Access Tool (Catalog Number 1764-DAT)
(Shown mounted on a Processor Unit.)
1-3
MicroLogix 1500 Programmable Controllers User Manual
Memory Modules/Real-Time Clock (Catalog Number 1764-MM1RTC,
1764-MM1, 1764-RTC)
(Shown mounted in a Processor Unit.)
Expansion I/O
Compact™ expansion I/O can be connected to the MicroLogix 1500 Controller. A
maximum of eight I/O modules may be connected to the base. See “System Loading
and Heat Dissipation” on page E-1 for more information on system configurations.
End Cap
An end cap terminator (catalog number 1769-ECR) must be used at the end of the
group of I/O modules attached to the MicroLogix 1500 Controller. The end cap
terminator is not provided with the base and processor units. It is required when using
expansion I/O.
1-4
Hardware Overview
Accessories
Cables
Use only the following communication cables in Class I, Division 2 hazardous
locations.
Environment Classification
Class I, Division 2 Hazardous Environment
Communication Cables
1761-CBL-PM02 Series C or later
1761-CBL-HM02 Series C or later
1761-CBL-AM00 Series C or later
1761-CBL-AP00 Series C or later
2707-NC8 Series B or later
2707-NC9 Series B or later
2707-NC10 Series B or later
2707-NC11 Series B or later
Programming
Programming the MicroLogix 1500 programmable controller is done using RSLogix
500, Rev. 3.01.00 or later. Programming cables are not provided.
Communication Options
The MicroLogix 1500 can be connected to a personal computer using the DF1
protocol. It can also be connected to the DH485 network using an Advanced Interface
Converter (catalog number 1761-NET-AIC) and to the DeviceNet network using a
DeviceNet Interface (catalog number 1761-NET-DNI). See “Connecting the System”
on page 4-1 for descriptions of these communication options.
1-5
MicroLogix 1500 Programmable Controllers User Manual
1-6
Installing Your Controller
2
Installing Your Controller
This chapter shows you how to install your controller system. The only tools you
require are a Flat or Phillips head screwdriver and drill. Topics include:
•
agency certifications
•
compliance to European Union Directives
•
using in hazardous locations
•
master control relay
•
power considerations
•
preventing excessive heat
•
controller spacing
•
mounting the controller
Agency Certifications
•
UL 508
•
C-UL under CSA C22.2 no. 142
•
Class I, Division 2, Groups A, B, C, D
(UL 1604, C-UL under CSA C22.2 no. 213)
•
CE compliant for all applicable directives
2-1
MicroLogix 1500 Programmable Controllers User Manual
Compliance to European Union Directives
This product has the CE mark and is approved for installation within the European
Union and EEA regions. It has been designed and tested to meet the following
directives.
EMC Directive
This product is tested to meet Council Directive 89/336/EEC Electromagnetic
Compatibility (EMC) and the following standards, in whole or in part, documented in
a technical construction file:
•
EN 50081-2
EMC - Generic Emission Standard, Part 2 - Industrial Environment
•
EN 50082-2
EMC - Generic Immunity Standard, Part 2 - Industrial Environment
This product is intended for use in an industrial environment.
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC Low Voltage, by applying
the safety requirements of EN 61131-2 Programmable Controllers, Part 2 Equipment Requirements and Tests.
For specific information required by EN 61131-2, see the appropriate sections in this
publication, as well as the following Allen-Bradley publications:
2-2
•
Industrial Automation Wiring and Grounding Guidelines for Noise Immunity,
publication 1770-4.1
•
Guidelines for Handling Lithium Batteries, publication AG-5.4
•
Automation Systems Catalog, publication B111
Installing Your Controller
General Considerations
Most applications require installation in an industrial enclosure (Pollution Degree 21)
to reduce the effects of electrical interference (Over Voltage Category II2) and
environmental exposure. Locate your controller as far as possible from power lines,
load lines, and other sources of electrical noise such as hard-contact switches, relays,
and AC motor drives. For more information on proper grounding guidelines, see the
Industrial Automation Wiring and Grounding Guidelines publication 1770-4.1.
!
ATTENTION: Vertical mounting is not recommended due to heat
build-up considerations.
!
ATTENTION: Be careful of metal chips when drilling mounting holes
for your controller or other equipment within the enclosure or panel.
Drilled fragments that fall into the base or processor unit could cause
damage. Do not drill holes above a mounted controller if the protective
debris strips have been removed or the processor has been installed.
1 Pollution Degree 2 is an environment where normally only non-conductive pollution occurs except that occasionally
temporary conductivity caused by condensation shall be expected.
2 Overvoltage Category II is the load level section of the electrical distribution system. At this level transient voltages
are controlled and do not exceed the impulse voltage capability of the products insulation.
2-3
MicroLogix 1500 Programmable Controllers User Manual
Safety Considerations
Safety considerations are an important element of proper system installation. Actively
thinking about the safety of yourself and others, as well as the condition of your
equipment, is of primary importance. We recommend reviewing the following safety
considerations.
Hazardous Location Considerations
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or nonhazardous locations only. The following ATTENTION statement applies to use in
hazardous locations.
ATTENTION: EXPLOSION HAZARD
!
•
Substitution of components may impair suitability for Class I,
Division 2.
•
Do not replace components or disconnect equipment unless power
has been switched off or the area is known to be non-hazardous.
•
Do not connect or disconnect components unless power has been
switched off or the area is known to be non-hazardous.
•
This product must be installed in an enclosure. All cables
connected to the product must remain in the enclosure or be
protected by conduit or other means.
Use only the following communication cables in Class I, Division 2 hazardous
locations.
Environment Classification
Class I, Division 2 Hazardous Environment
Communication Cables
1761-CBL-PM02 Series C or later
1761-CBL-HM02 Series C or later
1761-CBL-AM00 Series C or later
1761-CBL-AP00 Series C or later
2707-NC8 Series B or later
2707-NC9 Series B or later
2707-NC10 Series B or later
2707-NC11 Series B or later
2-4
Installing Your Controller
Disconnecting Main Power
!
ATTENTION: Explosion Hazard - Do not replace components or
disconnect equipment unless power has been switched off and the
area is known to be non-hazardous.
The main power disconnect switch should be located where operators and
maintenance personnel have quick and easy access to it. In addition to disconnecting
electrical power, all other sources of power (pneumatic and hydraulic) should be
de-energized before working on a machine or process controlled by a controller.
Safety Circuits
!
ATTENTION: Explosion Hazard - Do not connect or disconnect
connectors while circuit is live unless area is known to be nonhazardous.
Circuits installed on the machine for safety reasons, like overtravel limit switches,
stop push buttons, and interlocks, should always be hard-wired directly to the master
control relay. These devices must be wired in series so that when any one device
opens, the master control relay is de-energized thereby removing power to the
machine. Never alter these circuits to defeat their function. Serious injury or machine
damage could result.
Power Distribution
There are some points about power distribution that you should know:
•
The master control relay must be able to inhibit all machine motion by removing
power to the machine I/O devices when the relay is de-energized. It is
recommended that the controller remain powered even when the master control
relay is de-energized.
•
If you are using a dc power supply, interrupt the load side rather than the ac line
power. This avoids the additional delay of power supply turn-off. The dc power
supply should be powered directly from the fused secondary of the transformer.
Power to the dc input and output circuits should be connected through a set of
master control relay contacts.
2-5
MicroLogix 1500 Programmable Controllers User Manual
Periodic Tests of Master Control Relay Circuit
Any part can fail, including the switches in a master control relay circuit. The failure
of one of these switches would most likely cause an open circuit, which would be a
safe power-off failure. However, if one of these switches shorts out, it no longer
provides any safety protection. These switches should be tested periodically to assure
they will stop machine motion when needed.
Power Considerations
The following explains power considerations for the micro controllers.
Isolation Transformers
You may want to use an isolation transformer in the ac line to the controller. This type
of transformer provides isolation from your power distribution system to reduce the
electrical noise that enters the controller and is often used as a step down transformer
to reduce line voltage. Any transformer used with the controller must have a sufficient
power rating for its load. The power rating is expressed in volt-amperes (VA).
Power Supply Inrush
During power-up, the MicroLogix 1500 power supply allows a brief inrush current to
charge internal capacitors. Many power lines and control transformers can supply
inrush current for a brief time. If the power source cannot supply this inrush current,
the source voltage may sag momentarily.
The only effect of limited inrush current and voltage sag on the MicroLogix 1500 is
that the power supply capacitors charge more slowly. However, the effect of a voltage
sag on other equipment should be considered. For example, a deep voltage sag may
reset a computer connected to the same power source. The following considerations
determine whether the power source must be required to supply high inrush current:
•
The power-up sequence of devices in a system.
•
The amount of the power source voltage sag if the inrush current cannot be
supplied.
•
The effect of voltage sag on other equipment in the system.
If the entire system is powered-up at the same time, a brief sag in the power source
voltage typically will not affect any equipment.
2-6
Installing Your Controller
Loss of Power Source
The power supply is designed to withstand brief power losses without affecting the
operation of the system. The time the system is operational during power loss is called
“program scan hold-up time after loss of power.” The duration of the power supply
hold-up time depends on the type and state of the I/O, but is typically between 10
milliseconds and 3 seconds. When the duration of power loss reaches this limit, the
power supply signals the processor that it can no longer provide adequate dc power to
the system. This is referred to as a power supply shutdown. The processor then
performs an orderly shutdown of the controller.
Input States on Power Down
The power supply hold-up time as described above is generally longer than the turnon and turn-off times of the inputs. Because of this, the input state change from “On”
to “Off” that occurs when power is removed may be recorded by the processor before
the power supply shuts down the system. Understanding this concept is important.
The user program should be written to take this effect into account.
Other Types of Line Conditions
Occasionally the power source to the system can be temporarily interrupted. It is also
possible that the voltage level may drop substantially below the normal line voltage
range for a period of time. Both of these conditions are considered to be a loss of
power for the system.
2-7
MicroLogix 1500 Programmable Controllers User Manual
Preventing Excessive Heat
For most applications, normal convective cooling keeps the controller within the
specified operating range. Ensure that the specified temperature range is maintained.
Proper spacing of components within an enclosure is usually sufficient for heat
dissipation.
In some applications, a substantial amount of heat is produced by other equipment
inside or outside the enclosure. In this case, place blower fans inside the enclosure to
assist in air circulation and to reduce “hot spots” near the controller.
Additional cooling provisions might be necessary when high ambient temperatures
are encountered.
Note:
Do not bring in unfiltered outside air. Place the controller in an enclosure
to protect it from a corrosive atmosphere. Harmful contaminants or dirt
could cause improper operation or damage to components. In extreme
cases, you may need to use air conditioning to protect against heat buildup within the enclosure.
Master Control Relay
A hard-wired master control relay (MCR) provides a reliable means for emergency
machine shutdown. Since the master control relay allows the placement of several
emergency-stop switches in different locations, its installation is important from a
safety standpoint. Overtravel limit switches or mushroom head push buttons are wired
in series so that when any of them opens, the master control relay is de-energized.
This removes power to input and output device circuits. Refer to the figures on page
2-11 and 2-12.
!
2-8
ATTENTION: Never alter these circuits to defeat their function
since serious injury and/or machine damage could result.
Installing Your Controller
Note:
If you are using an external dc power supply, interrupt the dc output side
rather than the ac line side of the supply to avoid the additional delay of
power supply turn-off.
The ac line of the dc output power supply should be fused.
Connect a set of master control relays in series with the dc power
supplying the input and output circuits.
Place the main power disconnect switch where operators and maintenance personnel
have quick and easy access to it. If you mount a disconnect switch inside the
controller enclosure, place the switch operating handle on the outside of the
enclosure, so that you can disconnect power without opening the enclosure.
Whenever any of the emergency-stop switches are opened, power to input and output
devices should be removed.
When you use the master control relay to remove power from the external I/O circuits,
power continues to be provided to the controller’s power supply so that diagnostic
indicators on the processor can still be observed.
The master control relay is not a substitute for a disconnect to the controller. It is
intended for any situation where the operator must quickly de-energize I/O devices
only. When inspecting or installing terminal connections, replacing output fuses, or
working on equipment within the enclosure, use the disconnect to shut off power to
the rest of the system.
Note:
Do not control the master control relay with the controller. Provide the
operator with the safety of a direct connection between an emergencystop switch and the master control relay.
2-9
MicroLogix 1500 Programmable Controllers User Manual
Using Emergency-Stop Switches
When using emergency-stop switches, adhere to the following points:
•
Do not program emergency-stop switches in the controller program. Any
emergency-stop switch should turn off all machine power by turning off the
master control relay.
•
Observe all applicable local codes concerning the placement and labeling of
emergency-stop switches.
•
Install emergency-stop switches and the master control relay in your system.
Make certain that relay contacts have a sufficient rating for your application.
Emergency-stop switches must be easy to reach.
•
In the following illustration, input and output circuits are shown with MCR
protection. However, in most applications, only output circuits require MCR
protection.
The following illustrations show the Master Control Relay wired in a grounded
system.
Note:
2-10
In most applications input circuits do not require MCR protection;
however, if you need to remove power from all field devices, you must
include MCR contacts in series with input power wiring.
Installing Your Controller
Schematic (Using IEC Symbols)
L1
L2
230V ac
Disconnect
MCR
Fuse
230V ac
I/O
Circuits
Isolation
Transformer
X1
115V ac
or 230V
Fuse
X2
Operation of either ofthese contacts will
remove power from the external I/O
circuits, stopping machine motion.
Emergency-Stop
Push Button
Overtravel
Limit Switch
Stop
Master Control Relay (MCR)
Cat. No. 700-PK400A1
Suppressor
Cat. No. 700-N24
Start
MCR
Suppr.
MCR
MCR
115V ac or
230V ac
I/O Circuits
dc Power Supply.
Use IEC 950/EN 60950
_
(Hi)
(Lo)
Line Terminals: Connect to terminals
of Power Supply (1764-24AWA and
1764-24BWA).
+
MCR
24V dc
I/O
Circuits
Line Terminals: Connect to 24V dc
terminals of Power Supply.
2-11
MicroLogix 1500 Programmable Controllers User Manual
Schematic (Using ANSI/CSA Symbols)
L1
L2
230V ac
Disconnect
MCR
Fuse
Isolation
Transformer
X1
115V ac or
230V ac
Fuse
230V ac
Output
Circuits
Operation of either ofthese contacts will
remove power from the external I/O circuits,
X2
Master Control Relay (MCR)
Cat. No. 700-PK400A1
Suppressor
Cat. No. 700-N24
stopping machine motion.
Emergency-Stop
Push Button
Overtravel
Limit Switch
Stop
Start
MCR
Suppr.
MCR
MCR
115V ac or
230V ac
I/O Circuits
dc Power Supply.
Use NEC Class 2
for UL Listing.
_
(Lo)
MCR
24 V dc
I/O Circuits
(Hi)
Line Terminals:
Connect to 1764-24AWA
or 1764-24BWA terminals.
2-12
+
Line Terminals: Connect to 24V dc
terminals of Power Supply.
Installing Your Controller
Base Unit Mounting Dimensions
A
B
Dimension
C
1764-24AWA
1764-24BWA
1764-28BXB
Height (A)
DIN latch open: 138 mm (5.43 in.), DIN latch closed: 118 mm (4.65 in.)
Width (B)
168 mm (6.62 in.)
Depth (C)
87 mm (3.43 in.)
See “Controller Dimensions” on page A-9 for more dimensional information.
Controller Spacing
The base unit is designed to be mounted horizontally, with the Compact™ expansion
I/O extending to the right of the base unit. Allow 50 mm (2 in.) minimum of space on
all sides for adequate ventilation, as shown below.
End Cap
Compact I/O
Compact I/O
Compact I/O
Compact I/O
Controller
Side
Compact I/O
Top
Side
Bottom
2-13
MicroLogix 1500 Programmable Controllers User Manual
Mounting the Controller
!
ATTENTION: Do not remove protective debris strips until after the
base and all other equipment in the panel near the base is mounted and
wiring is complete. The debris strips are there to prevent drill
fragments, wire strands and other dirt from getting into the controller.
Once wiring is complete, remove protective debris strips and install
processor unit. Failure to remove strips before operating can cause
overheating.
Protective
Debris Strips
ESD Barrier
2-14
!
ATTENTION: Be careful of metal chips when drilling mounting holes
for your controller or other equipment within the enclosure or panel.
Drilled fragments that fall into the controller could cause damage. Do
not drill holes above a mounted controller if the protective debris strips
have been removed.
!
ATTENTION: Electrostatic discharge can damage semiconductor
devices inside the base unit. Do not touch the connector pins or other
sensitive areas.
Installing Your Controller
Note:
If additional I/O modules are required for the application, remove the ESD
barrier to install expansion I/O modules. A maximum of 8 I/O modules may
be connected to the base. The I/O module’s current requirements and power
consumption may further limit the number of modules connected to the base.
See “System Loading and Heat Dissipation” on page E-1. An end cap
terminator (catalog number 1769-ECR) is required at the end of the group of
I/O modules attached to the base.
Using a DIN Rail
The base unit and expansion I/O DIN rail latches lock in the open position so that an
entire system can be easily attached to or removed from the DIN rail. The maximum
extension of the latch is 15 mm (0.67 in.) in the open position. A flat-blade screw
driver is required for removal of the base unit. The base can be mounted to EN5002235x7.5 or EN50022-35x15 DIN rails. DIN rail mounting dimensions are shown
below.
B
A
DIN Rail Latch
C
Dimension
Height
A
DIN latch open: 138 mm (5.43 in.), DIN latch closed: 118 mm (4.65 in.)
B
47.6 mm (1.875 in.)
C
47.6 mm (1.875 in) DIN latch closed
54.7 mm (2.16 in.) DIN latch open
2-15
MicroLogix 1500 Programmable Controllers User Manual
To install your base unit on the DIN rail:
1. Mount your DIN rail. (Make sure that the placement of the base unit on the DIN
rail meets the recommended spacing requirements, see “Controller Spacing” on
page 2-13. Refer to the mounting template from the inside back cover of the
MicroLogix 1500 Programmable Controller Base Units Installation Instructions,
publication 1764-5.1.
2. Hook the top slot over the DIN rail.
3. While pressing the base unit down against the top of the rail, snap the bottom of
the base unit into position. Ensure DIN latches are in the up (secured) position.
4. Leave the protective debris strip attached until you are finished wiring the base
unit and any other devices.
To remove your base unit from the DIN rail:
1. Place a flat-blade screwdriver in the DIN rail latch at the bottom of the base unit.
2. Holding the base unit, pry downward on the latch until the latch locks in the open
position. Repeat this procedure with the second latch. This releases the base unit
from the DIN rail.
DIN Rail Latch
2-16
Installing Your Controller
Base Unit Panel Mounting
Mount to panel using #8 or M4 screws.
Mounting Template
To install your base unit using mounting screws:
1. Remove the mounting template from the inside back cover of the MicroLogix
1500 Programmable Controller Base Units Installation Instruction, publication
1764-5.1.
2. Secure the template to the mounting surface. (Make sure your base unit is spaced
properly, see “Controller Spacing” on page 2-13).
3. Drill holes through the template.
4. Remove the mounting template.
5. Mount the base unit.
6. Leave the protective debris strips attached until you are finished wiring the base
unit and any other devices.
2-17
MicroLogix 1500 Programmable Controllers User Manual
Installing Controller Components
Prevent Electrostatic Discharge
!
ATTENTION: Electrostatic discharge can damage integrated
circuits or semiconductors if you touch bus connector pins. Follow
these guidelines when you handle any module:
• Touch a grounded object to discharge static potential.
• Wear an approved wrist-strap grounding device.
• Do not touch the bus connector or connector pins.
• Do not touch circuit components inside the module.
• If available, use a static-safe work station.
• When not in use, keep the module in its static-shield bag.
!
2-18
ATTENTION: Be sure the base unit is free of all metal fragments
before removing protective debris strips and installing the processor
unit. Failure to remove strips before operating can cause overheating.
Installing Your Controller
Processor
1. Be sure base unit power is off.
2. Slide the processor into the base unit using the guide rails for alignment.
3. Push until a click is heard.
Important:
It is critical that the processor is fully engaged and locked into
place.
2-19
MicroLogix 1500 Programmable Controllers User Manual
4. Make sure the actuator is pushed closed.
5. To remove the processor from the base unit, make sure base unit power is off.
Push the actuator to the open position until the processor is ejected slightly. Once
the processor has been ejected, it can be removed from the base unit.
2-20
Installing Your Controller
Data Access Tool
1. Remove cover from processor.
2. Holding Data Access Tool (DAT) in the proper orientation (as shown), place DAT
onto processor. Align DAT port on the processor with the plug on the DAT.
2-21
MicroLogix 1500 Programmable Controllers User Manual
3. Firmly seat DAT on processor; make sure it seats into place.
4. To remove DAT, grasp using finger areas and pull upwards.
2-22
Installing Your Controller
Memory Module/Real-Time Clock
1. Remove the cover (or DAT if installed) from the processor as shown below.
!
ATTENTION: Electrostatic discharge can damage semiconductor
devices inside the base and processor units. Do not touch the
connector pins or other sensitive areas.
2-23
MicroLogix 1500 Programmable Controllers User Manual
2. Align connector on the memory module with the connector pins on the processor.
3. Firmly seat the memory module in the processor making sure the locking tabs
click into place.
4. Replace the cover (or DAT if used).
2-24
Installing Your Controller
Compact I/O
Attach and Lock Module (Module-to-Controller or Module-to-Module)
A Compact I/O module can be attached to the controller or an adjacent I/O module
before or after mounting to the panel or DIN rail. The module can be detached and
replaced while the system is mounted to a panel or DIN rail.
!
ATTENTION: Remove power before removing or inserting an I/O
module. When you remove or insert a module with power applied, an
electrical arc may occur. An electrical arc can cause personal injury or
property damage by:
•
sending an erroneous signal to your system’s field devices, causing
the controller to fault
•
causing an explosion in a hazardous environment
Electrical arcing causes excessive wear to contacts on both the module
and its mating connector. Worn contacts may create electrical
resistance, reducing product reliability.
!
ATTENTION: When attaching I/O modules, it is very important
that they are securely locked together to ensure proper electrical
connection.
2-25
MicroLogix 1500 Programmable Controllers User Manual
3
4
1
2
6
1
To attach and lock modules:
Note:
5
Remove ESD barrier when attaching I/O modules to a MicroLogix 1500
base unit.
1. Disconnect power.
2. Check that the bus lever of the module to be installed is in the unlocked (fully
right) position.
3. Use the upper and lower tongue-and-groove slots (1) to secure the modules
together (or to a controller).
4. Move the module back along the tongue-and-groove slots until the bus
connectors (2) line up with each other.
5. Push the bus lever back slightly to clear the positioning tab (3). Use your fingers
or a small screw driver.
6. To allow communication between the controller and module, move the bus lever
fully to the left (4) until it clicks. Ensure it is locked firmly in place.
!
ATTENTION: When attaching I/O modules, it is very important
that the bus connectors are securely locked together to ensure proper
electrical connection.
7. Attach an end cap terminator (5) to the last module in the system by using the
tongue-and-groove slots as before.
8. Lock the end cap bus terminator (6).
IMPORTANT: A 1769-ECR right end cap must be used to terminate the end of the
serial communication bus.
See “Controller Dimensions” on page A-9 for mounting dimensions.
2-26
Wiring Your Controller
3
Wiring Your Controller
This chapter describes how to wire your controller. Topics include:
•
wire requirements
•
using surge suppressors
•
grounding guidelines
•
sinking and sourcing circuits
•
wiring diagrams, input voltage ranges, and output voltage ranges
•
minimizing noise
Wire Requirements
Wire Size (2 wire maximum per
terminal screw)
Wire Type
Solid
Stranded
!
Cu-90°C
(194°F)
#14 to #22 AWG
Cu-90°C
(194°F)
#14 to #22 AWG
Wiring Torque
1.13 Nm (10 in-lb) rated
1.3 Nm (12 in-lb) maximum
ATTENTION: Be careful when stripping wires. Wire fragments
that fall into the controller could cause damage. Once wiring is
complete, be sure the base unit is free of all metal fragments before
removing protective debris strips and installing the processor unit.
Failure to remove strips before operating can cause overheating.
3-1
MicroLogix 1500 Programmable Controllers User Manual
Wiring Recommendation
B
!
ATTENTION: Before you install and wire any device, disconnect
power to the controller system.
!
ATTENTION: Calculate the maximum possible current in each
power and common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size. Current above the
maximum ratings may cause wiring to overheat, which can cause
damage.
ATTENTION: United States Only: If the controller is installed
within a potentially hazardous environment, all wiring must comply
with the requirements stated in the National Electrical Code 501-4
(b).
•
Allow for at least 50 mm (2 in.) between I/O wiring ducts or terminal strips and
the controller.
•
Route incoming power to the controller by a path separate from the device wiring.
Where paths must cross, their intersection should be perpendicular.
Note:
3-2
Do not run signal or communications wiring and power wiring in the
same conduit. Wires with different signal characteristics should be
routed by separate paths.
•
Separate wiring by signal type. Bundle wiring with similar electrical
characteristics together.
•
Separate input wiring from output wiring.
•
Label wiring to all devices in the system. Use tape, shrink–tubing, or other
dependable means for labeling purposes. In addition to labeling, use colored
insulation to identify wiring based on signal characteristics. For example, you may
use blue for dc wiring and red for ac wiring.
Wiring Your Controller
When wiring without spade lugs, it is recommended to keep the finger-safe covers in
place. Loosen the terminal screw and route the wires through the opening in the
finger-safe cover. Tighten the terminal screw making sure the pressure plate secures
the wire.
Finger-Safe Cover
Spade Lug Wiring
The diameter of the terminal screw head is 5.5 mm (0.220 in.). The input and output
terminals of the MicroLogix 1500 base unit are designed to accept a 6.35mm
(0.25 in.) wide spade (standard for #6 screw for up to 14 AWG) or a 4 mm (metric #4)
fork terminal.
When using spade lugs, use a small, flat-blade screwdriver to pry the finger-safe cover
from the terminal blocks, then loosen the terminal screw.
Finger-Safe Cover
3-3
MicroLogix 1500 Programmable Controllers User Manual
Using Surge Suppressors
Inductive load devices such as motor starters and solenoids require the use of some
type of surge suppression to protect the controller output contacts. Switching
inductive loads without surge suppression can significantly reduce the life expectancy
of relay contacts. By adding a suppression device directly across the coil of an
inductive device, you will prolong the life of the output or relay contacts. You will
also reduce the effects of voltage transients caused by interrupting the current to that
inductive device, and will reduce electrical noise from radiating into system wiring.
The following diagram shows an output with a suppression device. We recommend
that you locate the suppression device as close as possible to the load device.
+dc or L1
VAC/DC
Suppression
Device
Out 0
Out 1
Out 2
ac or dc
Outputs
Out 3
Out 4
Out 5
Out 6
Out 7
COM
dc COM or L2
If the outputs are dc, we recommend that you use an 1N4004 diode for surge
suppression, as shown in the illustration that follows.
+24V dc
VAC/DC
Out 0
Out 1
Out 2
Relay or Solid
State dc Outputs
Out 3
Out 4
IN4004 Diode
Out 5
Out 6
Out 7
COM
3-4
24V dc common
Wiring Your Controller
Suitable surge suppression methods for inductive ac load devices include a varistor,
an RC network, or an Allen–Bradley surge suppressor, all shown below. These
components must be appropriately rated to suppress the switching transient
characteristic of the particular inductive device. See the table on page 3-6 for
recommended suppressors.
Surge Suppression for Inductive ac Load Devices
Output Device
Output Device
Output Device
Surge
Suppressor
Varistor
RC Network
If you connect an expansion I/O triac output to control an inductive load, we
recommend that you use varistors to suppress noise. Choose a varistor that is
appropriate for the application. The suppressors we recommend for triac outputs
when switching 120V ac inductive loads are a Harris MOV, part number V175
LA10A, or an Allen–Bradley MOV, catalog number 599–K04 or 599–KA04. Consult
the varistor manufacturer’s data sheet when selecting a varistor for your application
For inductive dc load devices, a diode is suitable. A 1N4004 diode is acceptable for
most applications. A surge suppressor can also be used. See the table on page 3-6 for
recommended suppressors.
As shown in the illustration below, these surge suppression circuits connect directly
across the load device.
Surge Suppression for Inductive dc Load Devices
_
+
Output Device
Diode
(A surge suppressor can also be used.)
3-5
MicroLogix 1500 Programmable Controllers User Manual
Recommended Surge Suppressors
We recommend the Allen–Bradley surge suppressors shown in the following table for
use with Allen–Bradley relays, contactors, and starters.
Device
3-6
Coil Voltage
Suppressor Catalog
Number
Bulletin 509 Motor Starter
Bulletin 509 Motor Starter
120V ac
240V ac
599–K04
599–KA04
Bulletin 100 Contactor
Bulletin 100 Contactor
120V ac
240V ac
199–FSMA1
199–FSMA2
Bulletin 709 Motor Starter
120V ac
1401–N10
Bulletin 700 Type R, RM Relays
ac coil
None Required
Bulletin 700 Type R Relay
Bulletin 700 Type RM Relay
12V dc
12V dc
700–N22
700–N28
Bulletin 700 Type R Relay
Bulletin 700 Type RM Relay
24V dc
24V dc
700–N10
700–N13
Bulletin 700 Type R Relay
Bulletin 700 Type RM Relay
48V dc
48V dc
700–N16
700–N17
Bulletin 700 Type R Relay
Bulletin 700 Type RM Relay
115–125V dc
115–125V dc
700–N11
700–N14
Bulletin 700 Type R Relay
Bulletin 700 Type RM Relay
230–250V dc
230–250V dc
700–N12
700–N15
Bulletin 700 Type N, P, or PK Relay
150V max, ac or DC
700–N24
Miscellaneous electromagnetic
devices limited to 35 sealed VA
150V max, ac or DC
700–N24
Wiring Your Controller
Grounding the Controller
In solid-state control systems, grounding and wire routing helps limit the effects of
noise due to electromagnetic interference (EMI). Run the ground connection from the
ground screw of the base unit to the electrical panel’s ground bus prior to connecting
any devices. Use AWG #14 wire. This connection must be made for safety purposes.
This product is intended to be mounted to a well grounded mounting surface such as a
metal panel. Refer to the Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1, for additional information. Additional grounding connections
from the mounting tabs or DIN rail, if used, are not required unless the mounting
surface cannot be grounded. You must also provide an acceptable grounding path for
each device in your application.
Note:
For panel mounting installation: Be sure to use screws in the mounting
positions where there are grounding stampings.
Grounding Stamping
Grounding Stamping
Note:
This
symbol denotes a protective earth ground terminal which
provides a low impedance path between electrical circuits and earth for
safety purposes and provides noise immunity improvement. This
connection must be made for safety purposes.
!
ATTENTION: Remove the protective debris strips before applying
power to the controller. Failure to remove the strips may cause the
controller to overheat.
3-7
MicroLogix 1500 Programmable Controllers User Manual
Wiring Diagrams
The following illustrations show the wiring diagrams for the MicroLogix 1500
controllers. Controllers with dc inputs can be wired as either sinking or sourcing
configuration. (Sinking and sourcing does not apply to ac inputs.)
Note:
This
symbol denotes a protective earth ground terminal which
provides a low impedance path between electrical circuits and earth for
safety purposes and provides noise immunity improvement. This
connection must be made for safety purposes.
Sinking and Sourcing Circuits
Any of the MicroLogix 1500 DC embedded input groups can be configured as
sinking or sourcing depending on how the DC COM is wired on the group. See pages
3-10 through 3-13 for sinking and sourcing wiring diagrams.
Type
Sinking Input
The input energizes when high–level voltage is applied to the input terminal
(active high). Connect the power supply VDC (-) to the DC COM terminal.
Sourcing Input
The input energizes when low– level voltage is applied to the input terminal
(active low). Connect the power supply VDC (+) to the DC COM terminal.
!
3-8
Definition
ATTENTION: The 24V dc user power source should not be used
to power output circuits. It should only be used to power input devices
(e.g. sensors, switches). See page 2-8 for information on MCR wiring
in output circuits.
Wiring Your Controller
1764-24AWA Wiring Diagram1
Input Terminals
Output Terminals
1) “NOT USED” terminals are not intended for use as connection points.
3-9
MicroLogix 1500 Programmable Controllers User Manual
1764-24BWA Sinking Wiring Diagram
Input Terminals
Output Terminals
3-10
Wiring Your Controller
1764-24BWA Sourcing Wiring Diagram
Input Terminals
Output Terminals
3-11
MicroLogix 1500 Programmable Controllers User Manual
1764-28BXB Sinking Wiring Diagram1
Input Terminals
Output Terminals
1)“NOT USED” terminals are not intended for use as connection points.
3-12
Wiring Your Controller
1764-28BXB Sourcing Wiring Diagram1
Input Terminals
Output Terminals
1)“NOT USED” terminals are not intended for use as connection points.
3-13
MicroLogix 1500 Programmable Controllers User Manual
Controller I/O Wiring
Minimizing Electrical Noise
Because of the variety of applications and environments where controllers are
installed and operating, it is impossible to ensure that all environmental noise will be
removed by input filters. To help reduce the effects of environmental noise install the
MicroLogix 1500 system in a properly rated (i.e. NEMA) enclosure. Make sure that
the MicroLogix 1500 system is properly grounded.
A system may malfunction due to a change in the operating environment after a
period of time. We recommend periodically checking system operation, particularly
when new machinery or other noise sources are installed near the Micrologix 1500
system.
Transistor Output Transient Pulses
!
ATTENTION: A brief transient current pulse may flow through
transistor outputs if the external supply voltage is suddenly applied at
the V dc and V dc com terminals (e.g. via the master control relay).
It is a fast rate-of-change of voltage at the terminals that causes the
pulse. This condition is inherent in transistor outputs and is common
to solid state devices. The transient pulses may occur regardless of
whether the controller is powered or running. See chart on page 3-15.
The transient energy is dissipated in the load, and the pulse duration is longer for
loads of high impedance (or low current). The graph below illustrates the relation
between pulse duration and load current. Power-up transients do not exceed the times
shown in the graph. For most applications the pulse energy is not sufficient to
energize the load.
To reduce the possibility of inadvertent operation of devices connected to transistor
outputs, adhere to the following guidelines:
3-14
•
Either ensure that any programmable device connected to the transistor output is
programmed to ignore all output signals until after the transient pulse has ended
(filtering),
•
or add an external resistor in parallel to the load to increase the on-state load
current. The duration of the transient pulse is reduced when the on-state load
current is increased or the load impedance is decreased.
Wiring Your Controller
1.0
Transient Pulse Duration as a
Function of Load Current
0.9
Time - Duration of Transient (ms)
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1
100
200
300
400
500
600
700
800
900
1000
On-State Load Current (mA)
3-15
MicroLogix 1500 Programmable Controllers User Manual
3-16
Connecting the System
4
Connecting the System
This chapter describes how to communicate to your control system. The method you
use and cabling required to connect your controller depends on what type of system
you are employing. This chapter also describes how the controller establishes
communication with the appropriate network.
For information on:
See page:
DF1 protocol connections
4-3
DH485 network connections
4-8
Default Communication Configuration
The MicroLogix 1500 has the following default communication configuration. For
more information about communicating, see “Understanding the Communication
Protocols” on page D-1.
Table 4-1: DF1 Full-Duplex Configuration Parameters
Parameter
Baud Rate
Parity
Source ID (Node Address)
Control Line
Error Detection
Embedded Responses
Duplicate Packet (Message) Detect
ACK Timeout
NAK retries
ENQ retries
Stop Bits
Default
19.2K
none
1
no handshaking
CRC
auto detect
enabled
50 counts
3 retries
3 retries
1
4-1
MicroLogix 1500 Programmable Controllers User Manual
Using the Communications Toggle Push Button
The Communications Toggle Push Button is located on the processor. You cannot
access the button if the processor door or DAT is installed.
Use Communications Toggle Push Button to change from the user defined
communication configuration to the default communications mode and back. The
Default Communications (DCOMM) LED operates to show when the controller is in
the default communications mode (settings shown on 4-1).
COMMS
DC INPUTS
24V SINK/SOURCE
DC/RELAY OUT
24V SOURCE
Note:
4-2
The Communications Toggle Push Button must be pressed and held for one
second to activate.
Connecting the System
Connecting to the RS-232 Port
There are two ways to connect the MicroLogix 1500 programmable controller to your
personal computer using the DF1 protocol: using a point-to-point connection, or
using a modem. Descriptions of these methods follow.
!
ATTENTION: Chassis ground, internal 24V ground, and RS-232 ground are
internally connected. You must connect the chassis ground terminal screw to chassis
ground prior to connecting any devices. It is important that you understand your
personal computer’s grounding system before connecting to the controller. An optical
isolator is recommended between the controller and your personal computer.
Making a DF1 Isolated Point-to-Point Connection
You can connect the MicroLogix 1500 programmable controller to your personal
computer using a serial cable from your personal computer’s serial port to the
controller. The recommended protocol for this configuration is DF1 Full-Duplex.
MicroLogix
Controller
Optical Isolator
(recommended)
1761-CBL-PM02
Personal Computer
4-3
MicroLogix 1500 Programmable Controllers User Manual
We recommend using an Advanced Interface Converter (AIC+), catalog number
1761-NET-AIC, as your optical isolator. See page 4-13 for specific AIC+ cabling
information.
MicroLogix 1500
PC
1761-CBL-AM00
or 1761-CBL-HM02
1747-CP3 or 1761-CBL-AC00
24V dc
MicroLogix 1500 provides power
to the AIC+ or an external power
supply may be used.
Using a Modem
You can use modems to connect a personal computer to one MicroLogix 1500
controller (using DF1 Full-Duplex protocol) or to multiple controllers (using DF1
Half-Duplex protocol), as shown in the following illustration. Do not attempt to use
DH485 protocol through modems under any circumstance. (For information on types
of modems you can use with the micro controllers, see page D-8.)
Personal
Computer
Modem Cable
(straight-through)
MicroLogix
Controller
Modem
Protocol
DF1 Full-Duplex protocol (to 1 controller)
DF1 Half-Duplex Master protocol (to multiple controllers which
are using DF1 Half-Duplex Slave protocol)
Modem
Optical Isolator
(recommended)
We recommend using an AIC+, catalog number 1761-NET-AIC, as your optical
isolator. See page 4-13 for specific AIC+ cabling information.
4-4
Connecting the System
DF1 Isolated Modem Connection
MicroLogix 1500
1761-CBL-AM00
or 1761-CBL-HM02
Modem
User supplied modem cable
24V dc
MicroLogix 1500 provides power
to the AIC+ or an external power
supply may be used.
For additional information on connections using the AIC+, refer to the Advanced
Interface Converter (AIC+) User Manual, publication 1761-6.4.
Constructing Your Own Modem Cable
If you construct your own modem cable, the maximum cable length is 15.24 m (50 ft)
with a 25-pin or 9-pin connector. Refer to the following typical pinout for
constructing a straight-through cable:
AIC+
Optical Isolator
Modem
9-Pin
25-Pin
9-Pin
3
TXD
TXD
2
3
2
RXD
RXD
3
2
5
GND
GND
7
5
1
CD
CD
8
1
4
DTR
DTR
20
4
6
DSR
DSR
6
6
8
CTS
CTS
5
8
7
RTS
RTS
4
7
4-5
MicroLogix 1500 Programmable Controllers User Manual
Constructing Your Own Null Modem Cable
If you construct your own null modem cable, the maximum cable length is 15.24 m
(50 ft) with a 25-pin or 9-pin connector. Refer to the following typical pinout:
4-6
Optical Isolator
Modem
9-Pin
25-Pin
9-Pin
3
TXD
TXD
2
3
2
RXD
RXD
3
2
5
GND
GND
7
5
1
CD
CD
8
1
4
DTR
DTR
20
4
6
DSR
DSR
6
6
8
CTS
CTS
5
8
7
RTS
RTS
4
7
Connecting the System
Connecting to a DF1 Half-Duplex Network
Note:
Use this diagram for DF1 Half-Duplex Master-Slave protocol without
hardware handshaking.
Series B (or later) cables are required for hardware handshaking.
À DB-9 RS-232 port
Á mini-DIN 8 RS-232 port
 RS-485 port
4-7
MicroLogix 1500 Programmable Controllers User Manual
Connecting to a DH485 Network
MicroLogix DH485 Network
MicroLogix 1500
PC
connection from port 1 or
port 2 to MicroLogix
1761-CBL-AM00
or 1761-CBL-HM02
PC to port 1
or port 2
AIC+
3
2
1
1761-CBL-AP00
or 1761-CBL-PM02
1761-CBL-AP00
or 1761-CBL-PM02
AIC+
3
24V dc
(user supply needed if not
connected to a controller)
2
1
24V dc
(user supplied)
DB-9 RS-232 port
mini-DIN 8 RS-232 port
RS-485 port
1747-CP3
or 1761-CBL-AC00
Recommended Tools
To connect a DH485 network, you need tools to strip the shielded cable and to attach
the cable and terminators to the AIC+ Advanced Interface Converter. We recommend
the following equipment (or equivalent):
Table 4-2: Working with Cable for DH485 Network
Description
Part Number
Shielded Twisted Pair Cable
Stripping Tool
1/8” Slotted Screwdriver
4-8
Manufacturer
#3106A or #9842
Belden
45-164
Ideal Industries
Not Applicable
Not Applicable
Connecting the System
DH485 Communication Cable
The suggested DH485 communication cable is either Belden #3106A or #9842. The
cable is jacketed and shielded with one or two twisted wire pairs and a drain wire.
One pair provides a balanced signal line, and one additional wire is used for a
common reference line between all nodes on the network. The shield reduces the
effect of electrostatic noise from the industrial environment on network
communication.
The communication cable consists of a number of cable segments daisy-chained
together. The total length of the cable segments cannot exceed 1219 m (4000 ft).
When cutting cable segments, make them long enough to route them from one AIC+
to the next, with sufficient slack to prevent strain on the connector. Allow enough
extra cable to prevent chafing and kinking in the cable.
Use these instructions for wiring the Belden #3106A or #9842 cable. (If you are using
standard Allen-Bradley cables, see the Cable Selection Guide on page 3-12.)
Connecting the Communication Cable to the DH485 Connector
Note:
A daisy-chained network is recommended. We do not recommend the
following:
Belden #3106A
or #9842
Belden #3106A
or #9842
Belden #3106A
or #9842
Connector
Connector
Connector
Incorrect
4-9
MicroLogix 1500 Programmable Controllers User Manual
Single Cable Connection
Orange with White Stripes
White with Orange Stripes
6 Termination
5A
4B
3 Common
2 Shield
1 Chassis Ground
Shrink Tubing Recommended Blue (#3106A)
Drain Wire
or Blue with
White Stripes
(#9842)
Multiple Cable Connection
to Previous Device
to Next Device
Table 4-3: Connections using Belden #3106A Cable
For this Wire/Pair
Connect this Wire
To this Terminal
Shield/Drain
Non-jacketed
Terminal 2 - Shield
Blue
Blue
Terminal 3 - (Common)
White/Orange
White with Orange Stripe
Terminal 4 - (Data B)
Orange with White Stripe
Terminal 5 - (Data A)
Table 4-4: Connections using Belden #9842 Cable
For this Wire/Pair
Connect this Wire
To this Terminal
Shield/Drain
Non-jacketed
Terminal 2 - Shield
Blue/White
White with Blue Stripe
Cut back - no connection1
Blue with White Stripe
Terminal 3 - (Common)
White with Orange Stripe
Terminal 4 - (Data B)
Orange with White Stripe
Terminal 5 - (Data A)
White/Orange
1. To prevent confusion when installing the communication cable, cut back the white with blue stripe wire
immediately after the the insulation jacket is removed. This wire is not used by DH485.
4-10
Connecting the System
Grounding and Terminating the DH485 Network
Only one connector at the end of the link must have Terminals 1 and 2 jumpered
together. This provides an earth ground connection for the shield of the
communication cable.
Both ends of the network must have Terminals 5 and 6 jumpered together. This
connects the termination impedance (of 120Ω) that is built into each AIC+ as required
by the DH485 specification.
End-of-Line Termination
Jumper
Jumper
Belden #3106A or #9842 Cable
1219 m (4000ft) Maximum
Jumper
4-11
MicroLogix 1500 Programmable Controllers User Manual
Connecting the AIC+
The AIC+, catalog number 1761-NET-AIC, enables a MicroLogix 1500 to connect to
a DH485 network. The AIC+ has two RS-232 ports and one isolated RS-485 port.
Typically, there is one AIC+ for each MicroLogix 1500. When two MicroLogix
controllers are closely positioned, you can connect a controller to each of the RS-232
ports on the AIC+.
The AIC+ can also be used as an RS-232 isolator, providing an isolation barrier
between the MicroLogix 1500 communications port and any equipment connected to
it (i.e. personal computer, modem, etc.)
The following figure shows the external wiring connections and specifications of the
AIC+.
AIC+ Advanced Interface Converter
(1761-NET-AIC)
Item
Description
1
Port 1 - DB-9 RS-232, DTE
2
Port 2 - mini-DIN 8 RS-232 DTE
3
Port 3 - RS-485 Phoenix plug
4
DC Power Source selector switch
(cable = port 2 power source, external = external power source connected to item 5)
5
Terminals for external 24V dc power supply and chassis ground
For additional information on connecting the AIC+, refer to the Advanced Interface
Converter (AIC+) User Manual, publication 1761-6.4.
4-12
Connecting the System
Cable Selection Guide
1747-CP3
1761-CBL-AC00
Cable
Length
Connections from
to
AIC+
External
Power
Supply
Required1
1747-CP3
1761-CBL-AC00①
3m (9.8 ft)
45cm (17.7 in)
SLC 5/03 or SLC 5/04 processor, channel 0
port 1
yes
external
PC COM port
port 1
yes
external
PanelView 550 through NULL modem
adapter
port 1
yes
external
DTAM Plus / DTAM Micro™
port 1
yes
external
Port 1 on another AIC+
port 1
yes
external
Power
Selection
Switch Setting2
1. External power supply required unless the AIC+ is powered by the device connected to port 2, then the selection switch
should be set to cable.
2. Series B or higher cables are required for hardware handshaking.
1761-CBL-AS09
1761-CBL-AS03
Cable
1761-CBL-AS03
1761-CBL-AS09
Length
Connections from
3m (9.8 ft)
SLC 500 Fixed,
9.5m (31.17 ft) SLC 5/01, SLC 5/02, and SLC 5/03 processors
PanelView 550 RJ45 port
to
AIC+
External
Power
Supply
Required1
Power
Selection
Switch Setting1
port 3
yes
external
port 3
yes
external
1. External power supply required unless the AIC+ is powered by the device connected to port 2, then the selection switch
should be set to cable.
4-13
MicroLogix 1500 Programmable Controllers User Manual
1761-CBL-HM02➁
1761-CBL-AM00
Cable
Length
1761-CBL-AM00
1761-CBL-HM02➁
45cm (17.7 in)
2m (6.5 ft)
Connections from
to
AIC+
External
Power
Supply
Required1
Power
Selection
Switch Setting2
MicroLogix 1000 or 1500
port 2
no
cable
to port 2 on another AIC+
port 2
yes
external
1. External power supply required unless the AIC+ is powered by the device connected to port 2, then the selection switch
should be set to cable.
2. Series B or higher cables are required for hardware handshaking.
user supplied cable
Cable
straight 9-25 pin
Length
—
Connections from
modem or other communication device
to
AIC+
port 1
External
Power
Supply
Required1
yes2
Power
Selection
Switch Setting1
external2
1. External power supply required unless the AIC+ is powered by the device connected to port 2, then the selection switch
should be set to cable.
2. Series B or higher cables are required for hardware handshaking.
4-14
Connecting the System
1761-CBL-PM02➁
1761-CBL-AP00
Cable
Length
1761-CBL-AP00
45cm (17.7 in)
1761-CBL-PM02➁ 2m (6.5 ft)
Connections from
to
AIC+
External
Power
Supply
Required1
Power
Selection
Switch Setting1
SLC 5/03 or SLC 5/04 processors, channel 0
port 2
yes
external
MicroLogix 1000 or 1500
port 1
yes2
external2
PanelView 550 through NULL modem adapter
port 2
yes
external
DTAM Plus / DTAM Micro
port 2
yes
external
PC COM port
port 2
yes
external
1. Series B or higher cables are required for hardware handshaking.
2. External power supply required unless the AIC+ is powered by the device connected to port 2, then the selection switch
should be set to cable.
4-15
MicroLogix 1500 Programmable Controllers User Manual
1761-CBL-PM02 Series B or later Cable
5
4
3
2
1
9
8
7
6
8-pin Mini Din
9-pin D-shell
6 78
3
5
4
1761-CBL-PM02 Series B (or equivalent) Cable Wiring Diagram
4-16
Programming
Device
Controller
9-Pin D-Shell
8-Pin Mini Din
9
RI
24V
1
8
CTS
GND
2
7
RTS
RTS
3
6
DSR
RXD
4
5
GND
DCD
5
4
DTR
CTS
6
3
TXD
TXD
7
2
RXD
GND
8
1
DCD
1 2
Connecting the System
Recommended User-Supplied Components
These components can be purchased from your local electronics supplier.
Table 4-5: User Supplied Components
Component
Recommended Model
external power supply and chassis ground power supply rated for 20.4-28.8V dc
NULL modem adapter
standard AT
straight 9-25 pin RS-232 cable
see table below for port information if making own cables
1761-CBL-AP00 or 1761-CBL-PM02
RS-485 connector Port 3
DB-9 RS-232 Port 1
cable straight D
Table 4-6: AIC+ Terminals
Pin
1
2
3
4
5
6
7
8
9
Port 1: DB-9 RS-232
received line signal detector (DCD)
received data (RxD)
transmitted data (TxD)
Port 22: (1761-CBL-PM02 cable)
same state as port 1’s DCD signal
received data (RxD)
transmitted data (TxD)
DTE ready (DTR)1
signal common (GND)
DTE ready (DTR)3
signal common (GND)
2
DCE ready (DSR)
request to send (RTS)
clear to send (CTS)
not applicable
Port 3: RS-485 Connector
chassis ground
cable shield
signal ground
DH485 data B
DCE ready (DSR)3
DH485 data A
termination
request to send (RTS)
clear to send (CTS)
not applicable
not applicable
not applicable
not applicable
1. On port 1, pin 4 is electronically jumpered to pin 6. Whenever the AIC+ is powered on, pin 4 will match the state of pin 6.
2. An 8-pin mini DIN connector is used for making connections to port 2. This connector is not commercially available. If
you are making a cable to connect to port 2, you must configure your cable to connect to the Allen-Bradley cable shown
above.
3. In the 1761-CBL-PM02 cable, pins 4 and 6 are jumpered together within the DB-9 connector.
4-17
MicroLogix 1500 Programmable Controllers User Manual
Safety Considerations
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or nonhazardous locations only.
.
ATTENTION: EXPLOSION HAZARD -
!
•
AIC+ must be operated from an external power source.
•
This product must be installed in an enclosure. All cables connected to the
product must remain in the enclosure or be protected by conduit or other means.
See “Safety Considerations” on page 2-4 for additional information.
Installing and Attaching the AIC+
1. Take care when installing the AIC+ in an enclosure so that the cable connecting
the MicroLogix 1500 controller to the AIC+ does not interfere with the enclosure
door.
2. Carefully plug the terminal block into the RS-485 port on the AIC+ you are putting on the network. Allow enough cable slack to prevent stress on the plug.
3. Provide strain relief for the Belden cable after it is wired to the terminal block.
This guards against breakage of the Belden cable wires.
Powering the AIC+
In normal operation with the MicroLogix 1500 programmable controller connected to
port 2 of the AIC+, the controller powers the AIC+. Any AIC+ not connected to a
controller requires a 24V dc power supply. The AIC+ requires 120 mA at 24V dc.
If both the controller and external power are connected to the AIC+, the power
selection switch determines what device powers the AIC+.
!
4-18
ATTENTION: If you use an external power supply, it must be 24V dc. Permanent
damage will result if miswired with the wrong power source.
Connecting the System
Set the DC Power Source selector switch to EXTERNAL before connecting the
power supply to the AIC+.
Bottom View
24VDC
DC
NEUT
CHS
GND
ATTENTION: Always connect the CHS GND (chassis ground) terminal to the
nearest earth ground. This connection must be made whether or not an external 24V
dc supply is used.
!
Power Options
Below are two options for powering the AIC+:
•
Use the 24V dc user power supply built into the MicroLogix 1500 controller. The
AIC+ is powered through a hard-wired connection using a communication cable
(1761-CBL-HM02, or equivalent) connected to port 2.
•
Use an external DC power supply with the following specifications:
v operating voltage: 24V dc +20% / -15%
v output current: 150 mA minimum
v rated NEC Class 2
Make a hard-wired connection from the external supply to the screw terminals on
the bottom of the AIC+.
!
ATTENTION: If you use an external power supply, it must be 24V dc. Permanent
damage will result if miswired with the wrong power source.
4-19
MicroLogix 1500 Programmable Controllers User Manual
DeviceNet Communications
You can connect a MicroLogix 1500 to a DeviceNet network using the DeviceNet
Interface (DNI), catalog number 1761-NET-DNI. For additional information on using
the DNI, refer to the DeviceNet Interface User Manual, publication 1761-6.5.
V–
CAN_L
NET
SHIELD
CAN_H
DeviceNet Node (Port 1)
(Replacement connector
part no. 1761-RPL-0000)
V+
MOD
NODE
DANGER
Use this write-on
area to mark the
DeviceNet node
address.
TX/RX
GND
RS-232 (Port 2)
Cable Selection Guide
1761-CBL-HM02
1761-CBL-AM00
Cable
1761-CBL-AM00
1761-CBL-HM02
Length
45 cm (17.7 in)
2m (6.5 ft)
Connections from
MicroLogix 1000
port 2
MicroLogix 1500
port 2
1761-CBL-PM02
1761-CBL-AP00
Cable
1761-CBL-AP00
1761-CBL-PM02
4-20
to DNI
Length
45 cm (17.7 in)
2m (6.5 ft)
Connections from
to DNI
SLC 5/03 or SLC 5/04 processors, channel 0
port 2
PC COM port
port 2
Using Inputs and Outputs
5
Using Inputs and Outputs
This section discusses the various aspects of Input and Output features of the
MicroLogix 1500 controller. The controller comes with a certain amount of
“embedded” I/O, which is physically located on the Base Unit. The controller also
allows for adding Expansion I/O.
This section discusses the following I/O functions:
•
“Embedded I/O” on page 5-2
•
“Expansion I/O” on page 5-2
•
“I/O Configuration” on page 5-3
•
“I/O Forcing” on page 5-4
•
“Input Filtering” on page 5-5
•
“Latching Inputs” on page 5-6
5-1
MicroLogix 1500 Programmable Controllers User Manual
Embedded I/O
The MicroLogix 1500 provides discrete I/O that is built into the controller. These I/O
points are referred to as Embedded I/O.
I/O Configuration
Controller
1764-24BWA
1764-24AWA
1764-28BXB
Inputs
Quantity
12
12
16
Outputs
Type
24V dc
120V ac
24V dc
Quantity
12
12
12
Type
relay
relay
6 relay, 6 FET
DC embedded I/O can be configured for a number of special functions that can be
used in your application. These are: selectable input filters, high speed counting, event
interrupts, latching inputs, and high speed outputs (FET outputs only).
Expansion I/O
If the application requires more I/O than the controller provides, the user can attach
up to eight additional I/O modules. Compact I/O (Bulletin 1769) is used to provide
discrete inputs and outputs, analog inputs and outputs, and in the future, specialty
modules. The number of Compact I/O that can be attached to the MicroLogix 1500 is
dependent on the amount of current required by the I/O modules.
See “System Loading and Heat Dissipation” on page E-1 for more information on
valid configurations.
5-2
Using Inputs and Outputs
I/O Configuration
Embedded I/O
All embedded I/O is automatically configured to factory default settings and does not
require setup. If you need to change the input filters for any DC input controller
(1764-24BWA, 1764-28BXB), open RSLogix 500:
1. Open the “Controller” folder.
2. Open the “I/O Configuration” folder.
3. Open slot 0 (MicroLogix 1500).
4. Select the “embedded I/O configuration” tab.
5. You can change the filter settings for any of the input groups and configure the
latching inputs from this screen.
Expansion I/O
Expansion I/O must be configured for use with the MicroLogix 1500 controller.
Configuring expansion I/O can be done either manually, or automatically. Using
RSLogix 500:
1. Open the “Controller” folder.
2. Open the “I/O Configuration” folder.
3. For manual configuration, drag the Compact I/O module to the slot.
For automatic configuration, you must have the MicroLogix 1500 controller
connected to the computer (either directly or over a network). Click the “Read I/O
Config” button on the I/O configuration screen. RSLogix 500 will read the
existing configuration of the controllers I/O.
Some Compact I/O modules support or require configuration. To configure a specific
module, double-click on the module, an I/O configuration screen will open that is
specific to the module.
5-3
MicroLogix 1500 Programmable Controllers User Manual
One of the advanced features of the MicroLogix 1500 controller is the ability to
ignore a configuration error caused by an individual I/O module. This capability is
configured in the programming software on an individual module (slot) basis in the
Advanced Configuration screen. If the user chooses to ignore a configuration error for
a certain slot and that slot has a configuration error, the module will be ignored during
input and output scanning.
I/O Forcing
I/O forcing is the ability to override the actual status of the I/O at the user’s discretion.
The MicroLogix 1500 and RSLogix 500 both support I/O forcing.
Input Forcing
When an input is forced, the value in the input data file is set to a user-defined state.
For discrete inputs, you can force an input “on” or “off”. When an input is forced, it
no longer reflects the state of the physical input. For embedded inputs, the controller
reacts as if the force is applied to the physical input terminal.
Note:
When an input is forced in the controller, it has no effect on the input device
connected to the controller.
Output Forcing
When an output is forced, the controller overrides the status of the control program,
and sets the output to the user-defined state. Discrete outputs can be forced “on” or
“off”. The value in the output file is unaffected by the force. It maintains the state
determined by the logic in the control program. However, the state of the physical
output will be set to the forced state.
Note:
5-4
If you force an output controlled by an executing PTO or PWM function, an
instruction error is generated.
Using Inputs and Outputs
Input Filtering
The MicroLogix 1500 controller allows users to configure groups of inputs for highspeed or normal operation. Users can configure each input group’s filter response
time. The filter response determines how long after the external input voltage reaches
a valid “on” or “off” state to when the controller recognizes that change of state. The
higher the value, the longer it takes for the input state to be recognized by the
controller. Higher values provide more filtering, and are used in electrically noisy
environments. Lower values provide less filtering, and are used to detect fast or
narrow pulses. You typically set the filters to a lower value when using high speed
counters and latching inputs.
Input filtering is configured using RSLogix 500 programming software. To configure
the filters using RSLogix 500:
1. Open the “Controller” folder.
2. Open the “I/O Configuration” folder.
3. Open slot 0 (MicroLogix 1500)
4. Select the “embedded I/O configuration” tab.
The input groups are arranged. Simply select the filter time you require for each input
group. You can apply a unique input filter setting to each of five input groups:
•
0 and 1
•
2 and 3
•
4 and 5
•
6 and 7
•
8 and above
The minimum and maximum response times associated with each input filter setting
can be found in the tables under “Specifications” in Appendix A.
5-5
MicroLogix 1500 Programmable Controllers User Manual
Latching Inputs
The MicroLogix 1500 controller provides the ability to individually configure inputs
0 to 7 to be pulse catching or latching inputs (hereafter referred to as latching inputs).
A latching input is an input that captures a very fast pulse, and holds it for a single
controller scan. The pulse width that can be captured is dependent upon the input
filtering selected for that input.
To enable this feature using RSLogix 500:
1. Open the “Controller” folder.
2. Open the “I/O Configuration” folder.
3. Open slot 0 (MicroLogix 1500).
4. Select the “embedded I/O configuration” tab.
5. Select the mask bits for the inputs that you want to operate as latching inputs.
6. Select the state for the latching inputs. The controller can detect both “on” (rising
edge) and “off” (falling edge) pulses, depending upon the configuration selected
in the programming software. Enter “1” for rising edge, or “0” for falling edge.
The following information is provided for a controller looking for an “on” pulse.
When an external signal is detected “on”, the controller “latches” this event. In
general, at the next input scan following this event, the input image point is turned
“on” and remains “on” for the next controller scan. It is then set to “off” at the next
input scan. The following figures help demonstrate this.
5-6
Using Inputs and Outputs
Rising Edge Behavior - Example 1
Scan Number (X)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+1)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+2)
Input
Scan
Ladder
Scan
Output
Scan
External
Input
Latched
Status
Input File
Value
Rising Edge Behavior - Example 2
Scan Number (X)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+1)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+2)
Input
Scan
Ladder
Scan
Output
Scan
External
Input
Latched
Status
Input File
Value
Note:
The “gray” area of the Latched Status waveform is the input filter delay.
Important:
The input file value does not represent the external input when the
input is configured for latching behavior. When configured for
rising edge behavior, the input file value will normally be “off”
(“on” for 1 scan when a rising edge pulse is detected).
5-7
MicroLogix 1500 Programmable Controllers User Manual
The previous examples demonstrated rising edge behavior. Falling edge behavior
operates exactly the same way with these exceptions:
•
The detection is on the “falling edge” of the external input.
•
The input image will normally be “on” (1), and changes to “off” (0) for one scan.
Falling Edge Behavior - Example 1
Scan Number (X)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+1)
Input
Scan
Ladder
Scan
Scan Number (X+2)
Output
Scan
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+3)
Input
Scan
Ladder
Scan
Output
Scan
External
Input
Latched
Status
Input File
Value
Falling Edge Behavior - Example 2
Scan Number (X)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+1)
Input
Scan
Ladder
Scan
Output
Scan
Scan Number (X+2)
Input
Scan
Ladder
Scan
Output
Scan
External
Input
Latched
Status
Input File
Value
Note:
The “gray” area of the Latched Status waveform is the input filter delay.
Important:
5-8
7KHLQSXWILOHYDOXHGRHVQRWUHSUHVHQWWKHH[WHUQDOLQSXWZKHQWKH
LQSXWLVFRQILJXUHGIRUODWFKLQJEHKDYLRU:KHQFRQILJXUHGIRU
IDOOLQJHGJHEHKDYLRUWKHLQSXWILOHYDOXHZLOOQRUPDOO\EH³RQ´
³RII´IRUVFDQZKHQDIDOOLQJHGJHSXOVHLVGHWHFWHG
Controller Memory and File Types
6
Controller Memory and File Types
This chapter describes controller memory and the types of files used by the
MicroLogix 1500 controller. The chapter is organized as follows:
•
“Controller Memory” on page 6-2
•
“Data Files” on page 6-5
•
“Protecting Data Files During Download” on page 6-6
•
“Password Protection” on page 6-9
•
“Clearing the Controller Memory” on page 6-10
•
“Allow Future Access Setting (OEM Lock)” on page 6-11
•
“Function Files” on page 6-12
6-1
MicroLogix 1500 Programmable Controllers User Manual
Controller Memory
File Structure
MicroLogix 1500 user memory is comprised of Data Files, Function Files, and
Program Files. Function Files are new and exclusive to the MicroLogix 1500
controller, and are not available in the MicroLogix 1000 or SLC controllers.
0
1
4
Status File
5
6
6-2
Control File
EII
PWM
MMI
TPI
RTC
CS0
IOS
I/O Status File
Real Time Clock
Data Access Tool
DAT
Trim Pot Info.
Base Hardware Info.
BHI
Memory Module
Pulse Train Output
PTO
Pulse Width Mod.
High Speed Count.
HSC
Event Input Int.
Selectable Timed
STI
8 - 255
B
Bit
T
Timer
C
Counter
R
Control
N
Integer
L
Long Word
MG Message
PD
PID
Comms Status
Program
Files
Integer File
Timer File
Function
Files
7
Counter File
Data
Files
3
Bit File
MicroLogix 1500
Memory
Input File
Output File
2
Controller Memory and File Types
User Memory
User memory is the amount of storage available to a user for storing ladder logic, data
table files, I/O configuration, etc., in the controller.
User data files consist of the system status file, I/O image files, and all other usercreatable data files (bit, timer, counter, control, integer, long word, MSG, and PID).
The user word is defined as a unit of memory consumption in the controller. The
amount of memory available to the user for data files and program files is measured in
user words. Memory consumption is allocated as follows:
For data files, a user word is the equivalent of 16 bits of a data file element. For
example,
v 1 integer data file element = 1 user word
v 1 long word file element = 2 user words
v 1 timer data file element = 3 user words
For program files, a user word is the equivalent of a ladder instruction with one
operand. For example,
v 1 XIC instruction, which has 1 operand, consumes 1 user word
v 1 EQU instruction, which has 2 operands, consumes 2 user words
v 1 ADD instruction, which has 3 operands, consumes 3 user words
6-3
MicroLogix 1500 Programmable Controllers User Manual
The controller supports over 7K of user words. Memory can be used in any
combination of program files and data files as long as the total memory usage does
not exceed 4K user data words as shown below.
User Memory
Va
lid
Co
m
bi
na
tio
n
Data Words
4.0K
0.5K
0K
0K
Program Words
3.65K
4.35K
See “Memory Usage and Instruction Execution Time” on page F-1 to find the
memory usage for specific instructions.
6-4
Note:
Although the controller allows up to 256 elements in a file, it may not
actually be possible to create a file with that many elements due to the user
memory size in the controller.
Note:
For each additional file created in a user program, the file consumes one user
word of program space, plus the number of user words as determined by the
file’s type and number of elements.
Controller Memory and File Types
Data Files
Data files contain status information associated with the controller, external I/O, and
all other data associated with the instructions used in ladder subroutines. The data
files can also be used to store look-up tables and “recipes”. Data files are organized by
the type of information they contain. The data file types are:
File
Identifier
File
Number
Words per
Element
Output File
O
0
1
The Output File stores the values that are written to the
physical outputs during the Output Scan.
Input File
I
1
1
The Input File stores the values that are read from the physical
inputs during the Input Scan.
Status File
S
2
1
The contents of the Status File are determined by the functions
which utilize the Status File. See “System Status File” on page
G-1 for a detailed description.
Bit File
B
3 to 255
default = 3
1
The Bit File is a general purpose file whose locations are
referenced by ladder logic instructions.
Timer File
T
3 to 255
default = 4
3
The Timer File is used for maintaining timing information for
ladder logic timing instructions. See “Timer and Counter
Instructions” on page 13-1 for instruction information.
Counter File
C
3 to 255
default = 5
3
The Counter File is used for maintaining counting information
for ladder logic counting instructions. See “Timer and Counter
Instructions” on page 13-1 for instruction information.
Control File
R
3 to 255
default = 6
3
The Control Data file is used for maintaining length and
position information for various ladder logic instructions.
Integer File
N
3 to 255
default = 7
1
The Integer File is a general purpose file whose locations are
referenced by ladder logic instructions.
Long Word File
L
3 to 255
2
The Long Word File is a general purpose file whose locations
are referenced by ladder logic instructions.
Message File
MG
3 to 255
25
The Message File is associated with the MSG instruction. See
“Communications Instructions” on page 25-1 for information on
the MSG instruction.
PID File
PD
3 to 255
23
The PID File is associated with the PID instruction. See
“Process Control Instruction” on page 24-1 for more
information.
File Name
File Description
6-5
MicroLogix 1500 Programmable Controllers User Manual
Protecting Data Files During Download
Once a User Program is in the controller, there may be a need to update the ladder
logic and download it to the controller without destroying the contents of one or more
Data Files in the controller. This situation can occur when an application needs to be
updated, but the data that is relevant to the installation needs to remain intact.
This can be considered a form of file protection. The protection feature takes effect
when:
•
downloading a User Program via communications to the controller
•
transferring a User Program from a Memory Module to the controller
Setting Download File Protection
Download File Protection can be applied to the following data file types:
•
Output (O)
•
Input (I)
•
Binary (B)
•
Timer (T)
•
Counter (C)
•
Control (R)
•
Integer (N)
•
Proportional Integral Derivative (PD)
•
Message (MG)
•
Long (L)
Note:
6-6
The data in the Status File cannot be protected.
Controller Memory and File Types
You can access the Download File Protect feature using your programming software.
For each file you want protected, check the Memory Module/Download protection
box in the Data File Properties screen as shown below:
When a data file is Download File Protected, the values contained in it are preserved
during a download/transfer to the controller, if certain requirements are met.
6-7
MicroLogix 1500 Programmable Controllers User Manual
User Program Transfer Requirements
Download File Protection is in effect when the following conditions are met during a
User Program download or Memory Module transfer to the controller:
•
The controller contains protected data files.
•
The number of data files and executable files for the program currently in the
controller matches that of the program being transferred to the controller.
•
The file number, file type, and file size (number of elements) of the protected data
for the program currently in the controller exactly match that of the program being
transferred to the controller.
If all of the previous conditions are met, the controller will not write over any data file
in the controller that is configured as Download Protected.
If any of the previous conditions are not met, the entire User Program is transferred to
the controller. Additionally, if the program being transferred to the controller contains
protected files, the Data Protection Lost indicator (S:36/10) is set to indicate that
protected data has been lost. For example, a control program with protected files is
transferred to the controller. The original program did not have protected files, or the
files did not match. The data protection lost indicator (S:36/10) is then set. The data
protection lost indicator represents that the protected files within the controller have
default values, and the user application may need configuration/setup.
Note:
6-8
The controller will not clear the Data Protection Lost indicator. It is up to the
user to clear this bit.
Controller Memory and File Types
Password Protection
MicroLogix controllers have a built-in security system, based on numeric passwords.
Controller passwords consist of up to 10 digits (0-9). Each controller program may
contain two passwords, the Password and the Master Password.
Passwords restrict access to controllers. A Master Password essentially overrides the
Password. The idea is that all the controllers in a project would have different
Passwords, but the same Master Password, allowing access to all controllers for
supervisory or maintenance purposes.
You can establish, change, or delete a password by using the Controller Properties
dialog box. It is not necessary to use passwords, but if used, a master password is
ignored unless a password is also used.
If the Memory Module User Program has the “Load Always” functionality enabled,
and the controller User Program has a password specified, the controller will compare
the passwords before transferring the User Program from the Memory Module to the
controller. If the passwords do not match, the User Program is not transferred and the
program mismatch bit is set (S:5/9).
6-9
MicroLogix 1500 Programmable Controllers User Manual
Clearing the Controller Memory
If you are locked out because you do not have the password for the controller, you can
clear the controller memory and download a new User Program.
You can clear the memory when the programming software prompts you for a System
or Master Password to go on-line with the controller. To do so:
1. Enter 65257636 (the telephone keypad equivalent of MLCLRMEM, MicroLogix
Clear Memory).
2. When the Programming Software detects this number has been entered, it asks if
you want to clear the memory in the controller.
3. If you reply “yes” to this prompt, the programming software requests the controller to clear its User Program memory.
6-10
Controller Memory and File Types
Allow Future Access Setting (OEM Lock)
The controller supports a feature which allows you to select if future access to the
User Program should be allowed or disallowed after it has been transferred to the
controller. The Allow Future Access setting is shown in the Controller Properties
window. This setting corresponds to bit S:1/14 in the Status File where 0 means future
access is allowed (Allow Future Access selected), and 1 means future access is
disallowed (Allow Future Access deselected).
When deselected, the controller requires that the User Program in the controller is the
same as the one in a programming device. If the programming device does not have a
matching copy of the User Program, access to the User Program in the controller is
denied.
Note:
Functions such as change mode, clear memory, restore program, and transfer
memory module are allowed regardless of this selection.
This type of protection is particularly useful to an OEM (original equipment
manufacturer) who develops an application and then distributes the application via a
memory module or within a dedicated controller with the application installed in it.
6-11
MicroLogix 1500 Programmable Controllers User Manual
Function Files
Function Files are one of the three primary file structures within the MicroLogix 1500
controller (Program Files and Data Files are the others). Function Files were created
to provide an efficient and logical interface to controller resources. Controller
resources are resident (permanent) features such as the Real Time Clock and High
Speed Counter. The features are available to the control program through either
instructions that are dedicated to a specific function file, or via standard instructions
such as MOV and ADD. The Function File types are:
Table 6-1: Function Files
File Name
File Identifier
File Description
High Speed
Counter
HSC
This file type is associated with the High Speed Counter Interrupt function. See page “Using
the High Speed Counter” on page 9-1 for more information.
Pulse Train
Output
PTO
This file type is associated with the Pulse Train Output Instruction. See “PTO - Pulse Train
Output Instruction” on page 10-1 for more information.
Pulse Width
Modulation
PWM
This file type is associated with the Pulse Width Modulation instruction. See “Pulse Train
Output Function” on page 10-1 for more information.
Selectable Timed
Interrupt
STI
This file type is associated with the Selectable Timed Interrupt function. See “Using the
Selectable Timed Interrupt (STI) Function File” on page 23-13 for more information.
Event Input
Interrupt
EII
This file type is associated with the Event Input Interrupt instruction. See “Using the Event
Input Interrupt (EII) Function File” on page 23-19 for more information.
Real Time Clock
RTC
This file type is associated with the Real Time Clock (time of day) function. See“Real Time
Clock Operation” on page 8-1 for more information.
Data Access Tool
Information
DAT
This file type contains information about the Data Access Terminal. See “DAT Function File”
on page 7-6 for more information.
Trim Pot
Information
TPI
This file type contains information about the Trim Pots. See “Trim Pot Information Function
File” on page 7-2 for more information.
Memory Module
Information
MMI
This file type contains information about the Memory Module. See “Memory Module
Information File” on page 8-5 for more information.
Base Hardware
Information
BHI
This file type contains information about the Base Unit hardware. See “Base Hardware
Information Function File” on page 6-13 for the file structure.
Communications
Status File
CS0
This file type contains information about the Communications with the controller. See
“Communications Status File” on page 6-13 for the file structure.
I/O Status File
IOS
This file type contains information about the controller I/O. See “Input/Output Status File” on
page 6-17 for the file structure.
6-12
Controller Memory and File Types
Base Hardware Information Function File
The base hardware information file is a read-only file. It contains a description of the
MicroLogix 1500 Base Unit.
Table 6-2: Base Hardware Information Function File (BHI)
Address
BHI:0.CN
BHI:0.SRS
BHI:0.REV
BHI:0.FT
Description
CN - Catalog Number
SRS - Series
REV - Revision
FT - Functionality Type
Communications Status File
The communications status file is a read-only file in the controller that contains
information on how the controller communication parameters are configured, and
status information on communications activity.
Note:
You can use the Communications Status File information as a
troubleshooting tool for communications issues.
The data file is structured as:
Table 6-3: Communications Status File
Word
0 to 5
6 to 22
23 to 42
43
Description
General Channel Status Block
DLL Diagnostic Counters Block
DLL Active Node Table Block
End of List Category Identifier Code (always 0)
6-13
MicroLogix 1500 Programmable Controllers User Manual
Table 6-4: Channel 0 General Channel Status Block
Word
0
1
2
3
4
5
6-14
Bit
-
Description
Communications Channel General Status Information Category Identifier Code
(always 1)
Length (always 8)
Format Code (always 0)
Communications Configuration Error Code
0
ICP – Incoming Command Pending Bit
This bit is set (1) when the controller determines that another device has
requested information from this controller. Once the request has been satisfied,
the bit is cleared (0).
1
MRP – Incoming Message Reply Pending Bit
This bit is set (1) when the controller determines that another device has supplied
the information requested by a MSG instruction executed by this controller. When
the appropriate MSG instruction is serviced (during end-of-scan, SVC, or REF),
this bit is cleared (0).
2
MCP – Outgoing Message Command Pending Bit
This bit is set (1) when the controller has one or more MSG instructions enabled
and in the communication queue. This bit is cleared (0) when the queue is empty.
3
SSB – Selection Status Bit
This bit indicates that the controller is in the System Mode. It is always set.
4
CAB – Communications Active Bit
This bit is set (1) when at least one other device is on the DH485 network. If no
other devices are on the network, this bit is cleared (0).
5 to 13 Reserved
14
Reserved for MLB – Modem Lost Bit
15
Reserved
0 to 7 Node Address - This byte value contains the node address of your controller on
the network.
8 to 15 Baud Rate - This byte value contains the baud rate of the controller on the
network.
Controller Memory and File Types
Table 6-5: DH485 DLL Diagnostic Counters Block
Word
6
7
8
9
10
11
12
13
14 to 22
Bit
0 to 7
8 to 15
0 to 7
8 to 15
0 to 7
8 to 15
-
Description
DLL Diagnostic Counters Category Identifier Code (always 2)
Length (always 30)
Format Code (always 0)
Total Message Packets Received
Total Message Packets Sent
Message Packet Retries
Retry Limit Exceeded (Non-Delivery)
NAK – No Memories Sent
NAK – No Memories Received
Total Bad Message Packets Received
Reserved
Reserved
Table 6-6: DF1 Full-Duplex DLL Diagnostic Counters Block
Word
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Bit
0
1
2 to 15
-
Description
DLL Diagnostic Counters Category Identifier Code (always 2)
Length (always 30)
Format Code (always 1)
CTS
RTS
Reserved for Modem Control Line States
Total Message Packets Sent
Total Message Packets Received
Undelivered Message Packets
ENQuiry Packets Sent
NAK Packets Received
ENQuiry Packets Received
Bad Message Packets Received and NAKed
No Buffer Space and Naked
Duplicate Message Packets Received
Reserved
Reserved for DCD Recover Field
Reserved for Lost Modem Field
Reserved
6-15
MicroLogix 1500 Programmable Controllers User Manual
Table 6-7: DF1 Half-Duplex Slave DLL Diagnostic Counters Block
Word
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Bit
0
1
2 to 15
-
Description
DLL Diagnostic Counters Category Identifier Code (always 2)
Length (always 30)
Format Code (always 2)
Reserved for Modem Control Line States
RTS
CTS
Total Message Packets Sent
Total Message Packets Received
Undelivered Message Packets
Message Packets Retried
NAK Packets Received
Polls Received
Bad Message Packets Received
No Buffer Space
Duplicate Message Packets Received
Reserved
Reserved for DCD Recover Field
Reserved for Lost Modem Field
Reserved
Table 6-8: Active Node Table Block
6-16
Word
23
24
25
26
Bit
-
27
-
28
-
29 to 42
-
Description
DLL Active Node Table Category Identifier Code (always 3)
Length (always 13)
Format Code (always 0)
Number of Nodes (always 32 for DH485, always 0 for DF1 Full-Duplex and HalfDuplex Slave)
Active Node Table – Nodes 0 to 15 (CS0:27/1 is node 1, CS0:27/2 is node 2, etc.) This
is a bit-mapped register that displays the status of each node on the network. If a bit is
set (1), the corresponding node is active on the network. If a bit is clear (0), the
corresponding node is inactive.
Active Node Table – Nodes 15 to 31 (CS0:28/1 is node 15, CS0:28/2 is node 16, etc.)
This is a bit-mapped register that displays the status of each node on the network. If a
bit is set (1), the corresponding node is active on the network. If a bit is clear (0), the
corresponding node is inactive.
Reserved for Active Node Table – Nodes 32 - 255
Controller Memory and File Types
Input/Output Status File
The input/output status file is a read-only file in the controller that contains
information on the status of the embedded and local expansion I/O. The data file is
structured as:
Table 6-9: I/O Status File
Word
0
1-8
Description
Embedded Module Error Code – Always zero
Expansion Module Error Code – The word number corresponds to the module’s
slot number. Refer to the I/O module’s documentation for more information.
6-17
MicroLogix 1500 Programmable Controllers User Manual
6-18
Using Trim Pots and the Data Access Tool (DAT)
7
Using Trim Pots and the
Data Access Tool (DAT)
Trim Pot Operation
The processor has two trimming potentiometers (trim pots) which allow modification
of data within the controller. Adjustments to the trim pots change the value in the
corresponding Trim Pot Information (TPI) register. The data value of each trim pot
can be used throughout the control program as timer, counter, or analog presets
depending upon the requirements of the application.
The trim pots are located below the mode switch under the left access door of the
processor.
Trim Pot 0
RUN
REM
PROG
Trim Pot 1
7-1
MicroLogix 1500 Programmable Controllers User Manual
Use a small flathead screwdriver to turn the trim pots. Adjusting their value causes
data to change within a range of 0 to 250 (fully clockwise). The maximum rotation of
each trim pot is three-quarters, as shown below. Trim pot stability over time and
temperature is typically ±2 counts.
Maximum
(fully clockwise)
Minimum
(fully counterclockwise)
Trim pot file data is updated continuously whenever the controller is under power.
Trim Pot Information Function File
The composition of the Trim Pot Information (TPI) Function File is described below.
Data
Address
Data Format
Range
Type
User Program
Access
TPD Data O
TPI:0.POT0
Word (16-bit integer)
0 - 250
Status
Read Only
TPD Data 1
TPI:0.POT1
Word (16-bit integer)
0 - 250
Status
Read Only
0-3
Status
Read Only
Word (bits 0-7)
TPD Error Code TPI:0.ER
Word (bits 8-15)
The data resident in TPI:0.POT0 represents the position of trim pot 0. The data
resident in TPI:0.POT1 corresponds to the position of trim pot 1. The valid data range
for both is from 0 (counterclockwise) to 250 (clockwise).
Error Conditions
If the controller detects a problem with either trim pot, the last values read remain in
the data location, and an error code is put in the error code byte of the TPI file for
whichever trim pot had the problem. Once the controller can access the trim pot
hardware, the error code is cleared. The error codes are described in the table below.
Error Code
7-2
Description
0
Trim pot data is valid.
1
Trim pot subsystem detected, but data is invalid.
2
Trim pot subsystem did not initialize.
3
Trim pot subsystem failure.
Using Trim Pots and the Data Access Tool (DAT)
Data Access Tool (DAT)
The DAT is a convenient and simple tool that provides an interface for editing and
monitoring data. The DAT has five primary features:
•
Direct access to 48 bit elements
•
Direct access to 48 integer elements
•
Two function keys
•
Display of controller faults
•
Removal/Insertion under power
DAT Keypad and Indicator Light Functions
The DAT has a digital display, 6 keys, an up/down key, and indicator lights. Their
functions are described in the table on page 7-4.
PROTECTED
F1
F2
ESC
BIT
INT
ENTER
7-3
MicroLogix 1500 Programmable Controllers User Manual
Feature
Function
Digital Display
Displays address elements and data values, faults and errors.
Up/Down Key
Scroll to select element numbers and change data values. The up/down key
repeats when held.
F1 Key and
Indicator Light
Controls the F1 function key status bit. When the F1 key status bit is pressed or
latched, the F1 indicator LED is lit.
F2 Key and
Indicator Light
Controls the F2 function key status bit. When the F2 key status bit is pressed or
latched, the F2 indicator LED is lit.
ESC Key
Cancels an edit in progress.
BIT Key and
Indicator Light
Pressing the BIT key puts the DAT in bit monitoring mode. The bit indicator light is
on when the DAT is in bit monitoring mode.
INT Key and
Indicator Light
Pressing the INT key puts the DAT in integer monitoring mode. The integer
indicator light is on when the DAT is in integer monitoring mode.
ENTER Key
Press to select the flashing element number or data value.
PROTECTED
Indicator Light
Indicates protected data that cannot be changed using the DAT.
Note:
7-4
The F1, F2, ESC, BIT, INT, and ENTER keys do not repeat when held.
Holding down any one of these keys results in only one key press. The
Up/Down arrow key is the only key that repeats when held.
Using Trim Pots and the Data Access Tool (DAT)
Power-Up Operation
The DAT receives power when it is plugged into the controller. Upon power-up, the
DAT performs a self-test.
If the test fails, the DAT displays an error code. All indicator lights are deactivated,
and the DAT does not respond to any key presses. See “DAT Error Codes” on page 716.
PROTECTED
F1
F2
ESC
BIT
INT
ENTER
After a successful self-test, the DAT reads the DAT function file to determine its
configuration.
Following a successful power-up sequence, the DAT enters the bit monitoring mode.
PROTECTED
00
off-0
F1
F2
ESC
BIT
INT
ENTER
7-5
MicroLogix 1500 Programmable Controllers User Manual
DAT Function File
DAT configuration is stored in the processor in a specialized configuration file called
the DAT Function File. The DAT Function File, which is part of the user’s control
program, is shown below.
The DAT function file contains the Target Integer File, the Target Bit File, and the
Power Save Timeout parameter. These three parameters are described in the table
below.
Feature
Address
Data Format
Type
User Program Access
Target Integer File
DAT:0.TIF
Word (int)
Control
Read Only
Target Bit File
DAT:0.TBF
Word (int)
Control
Read Only
Power Save Timeout
DAT:0.PST
Word (int)
Control
Read Only
Target Integer File (TIF)
The DAT can read or write to any valid integer file within the controller. The value
stored in the TIF location identifies the integer file with which the DAT will interface.
Valid integer files are N3 through N255. When the DAT reads a valid integer file
number, it can access the first 48 elements (0-47) of the specified file on its display
screen. The next 48 bits (words 48-50) are used to define the read only or read/write
privileges for the 48 elements.
7-6
Using Trim Pots and the Data Access Tool (DAT)
The only integer file that DAT interfaces with is the file specified in the TIF location.
The TIF location can only be changed by a program download.
Important:
Use your programming software to ensure that the integer file you
specify in the TIF location, as well as the appropriate number of
elements, exist in the MicroLogix 1500 user program.
The example table below shows a DAT configured to use integer file number 50
(DAT:0.TIF = 50).
Element
Number
Data Address
Protection Bit
Element
Number
Data Address
Protection Bit
0
N50:0
N50:48/0
24
N50:24
N50:49/8
1
N50:1
N50:48/1
25
N50:25
N50:49/9
2
N50:2
N50:48/2
26
N50:26
N50:49/10
3
N50:3
N50:48/3
27
N50:27
N50:49/11
4
N50:4
N50:48/4
28
N50:28
N50:49/12
5
N50:5
N50:48/5
29
N50:29
N50:49/13
6
N50:6
N50:48/6
30
N50:30
N50:49/14
7
N50:7
N50:48/7
31
N50:31
N50:49/15
8
N50:8
N50:48/8
32
N50:32
N50:50/0
9
N50:9
N50:48/9
33
N50:33
N50:50/1
10
N50:10
N50:48/10
34
N50:34
N50:50/2
11
N50:11
N50:48/11
35
N50:35
N50:50/3
12
N50:12
N50:48/12
36
N50:36
N50:50/4
13
N50:13
N50:48/13
37
N50:37
N50:50/5
14
N50:14
N50:48/14
38
N50:38
N50:50/6
15
N50:15
N50:48/15
39
N50:39
N50:50/7
16
N50:16
N50:49/0
40
N50:40
N50:50/8
17
N50:17
N50:49/1
41
N50:41
N50:50/9
18
N50:18
N50:49/2
42
N50:42
N50:50/10
19
N50:19
N50:49/3
43
N50:43
N50:50/11
20
N50:20
N50:49/4
44
N50:44
N50:50/12
21
N50:21
N50:49/5
45
N50:45
N50:50/13
22
N50:22
N50:49/6
46
N50:46
N50:50/14
23
N50:23
N50:49/7
47
N50:47
N50:50/15
7-7
MicroLogix 1500 Programmable Controllers User Manual
The element number displayed on the DAT corresponds to the data register as
illustrated in the table. The protection bit defines whether the data is read/write or
read only. When the protection bit is set (1), the corresponding data address is
considered read only by the DAT. The Protected LED illuminates whenever a read
only element is active on the DAT display. When the protection bit is clear (0) or the
protection bit does not exist, the Protected LED is off and the data within the
corresponding address is editable from the DAT keypad.
Important:
Note:
Although the DAT does not allow protected data to be changed
from its keypad, the control program or other communication
devices do have access to this data. Protection bits do not provide
any overwrite protection to data within the target integer file. It is
entirely the user’s responsibility to ensure that data is not
inadvertently overwritten.
•
Remaining addresses within the target file can be used without
restrictions (addresses N50:51 and above, in this example).
•
The DAT always starts at word 0 of a data file. It cannot start at any
other address within the file.
Target Bit File (TBF)
The DAT can read or write to any valid bit file within the controller. The value stored
in the TBF location identifies the bit file with which the DAT will interface. Valid bit
files are B3 through B255. When the DAT reads a valid bit file number, it can access
the first 48 elements (0-47) of the specified file on its display screen. The next 48 bits
(48-95) are used to define the read only or read/write privileges for the first 48
elements.
The only bit file that the DAT interfaces with is the file specified in the TBF location.
The TBF location can only be changed by a program download.
Important:
7-8
Use your programming software to ensure that the bit file you
specify in the TBF location, as well as the appropriate number of
elements, exist in the MicroLogix 1500 user program.
Using Trim Pots and the Data Access Tool (DAT)
The example table below shows how the DAT uses the configuration information with
bit file number 51 (DAT:0.TBF=51).
Element
Number
Data Address
Protection Bit
Element
Number
Data Address
Protection Bit
0
B51/0
B51/48
24
B51/24
B51/72
1
B51/1
B51/49
25
B51/25
B51/73
2
B51/2
B51/50
26
B51/26
B51/74
3
B51/3
B51/51
27
B51/27
B51/75
4
B51/4
B51/52
28
B51/28
B51/76
5
B51/5
B51/53
29
B51/29
B51/77
6
B51/6
B51/54
30
B51/30
B51/78
7
B51/7
B51/55
31
B51/31
B51/79
8
B51/8
B51/56
32
B51/32
B51/80
9
B51/9
B51/57
33
B51/33
B51/81
10
B51/10
B51/58
34
B51/34
B51/82
11
B51/11
B51/59
35
B51/35
B51/83
12
B51/12
B51/60
36
B51/36
B51/84
13
B51/13
B51/61
37
B51/37
B51/85
14
B51/14
B51/62
38
B51/38
B51/86
15
B51/15
B51/63
39
B51/39
B51/87
16
B51/16
B51/64
40
B51/40
B51/88
17
B51/17
B51/65
41
B51/41
B51/89
18
B51/18
B51/66
42
B51/42
B51/90
19
B51/19
B51/67
43
B51/43
B51/91
20
B51/20
B51/68
44
B51/44
B51/92
21
B51/21
B51/69
45
B51/45
B51/93
22
B51/22
B51/70
46
B51/46
B51/94
23
B51/23
B51/71
47
B51/47
B51/95
7-9
MicroLogix 1500 Programmable Controllers User Manual
The element number displayed on the DAT corresponds to the data bit as illustrated in
the table. The protection bit defines whether the data is editable or read only. When
the protection bit is set (1), the corresponding data address is considered read only by
the DAT. The Protected LED illuminates whenever a read only element is active on
the DAT display. When the protection bit is clear (0) or the protection bit does not
exist, the Protected LED is off and the data within the corresponding address is
editable from the DAT keypad.
Important:
Note:
Although the DAT does not allow protected data to be changed
from its keypad, the control program or other communication
devices do have access to this data. Protection bits do not provide
any overwrite protection to data within the target bit file. It is
entirely the user’s responsibility to ensure that data is not
inadvertently overwritten.
•
Remaining addresses within the target file can be used without
restrictions (addresses B51/96 and above, in this example).
•
The DAT always starts at bit 0 of a data file. It cannot start at any
other address within the file.
Power Save Timeout (PST) Parameter
The power save timeout turns off the DAT display after keypad activity has stopped
for a user-defined period of time.1 The power-save (DAT:0.PST) value is set in the
DAT Function File. The valid range is 0 to 255 minutes. The power-save feature can
be disabled by setting the PST value to 0, which keeps the display on continuously.
The default value is 0.
In power-save mode, a dash flashes in the left of the display. Press any key, except F1
or F2, to return the DAT to its previous mode. If F1 or F2 is pressed, the DAT will
change the value of the F1 or F2 status bits, but the display remains in power-save
mode.
1.
7-10
F1 and F2 keys do not apply.
Using Trim Pots and the Data Access Tool (DAT)
Understanding the DAT Display
When the DAT enters either the integer or bit mode, the element number and a data
value are displayed, as shown below.
Integer Mode Display
Bit Mode Display
PROTECTED
PROTECTED
1 2- 32768
00
off-0
F1
F2
ESC
F1
F2
ESC
BIT
INT
ENTER
BIT
INT
ENTER
integer
element
number
• 0 to 47
integer data
• -32,768 to 32,767
• – – – (undefined)
bit
element
number
• 0 to 47
bit data
• OFF - 0
• ON - 1
• – – – (undefined)
If the element is defined and is not protected, the element number flashes, indicating
that it can be modified.
If the element is protected, the PROTECTED indicator light illuminates, and the
element number does not flash, indicating that the element cannot be modified.
If the element is undefined, the data field displays three dashes. The element number
does not flash because the element cannot be modified.
PROTECTED
---
05
F1
F2
ESC
BIT
INT
ENTER
7-11
MicroLogix 1500 Programmable Controllers User Manual
Entering Integer Monitoring Mode
Integer monitoring mode allows you to view and modify 16-bit integer data locations
in the controller. To initiate integer monitoring mode, press the INT key. If the integer
monitoring mode was previously invoked, the DAT displays the last integer element
monitored. If the integer monitoring mode was not previously invoked, the DAT
displays the first element of the list. However, there may be a brief delay while the
DAT requests information from the controller. If there is a delay, the working screen is
displayed. See “Working Screen Operation” on page 7-14.
Entering Bit Monitoring Mode
Bit monitoring allows you to view and modify bit locations in the controller. The DAT
enters the bit monitoring mode automatically following a successful power-up. The
bit monitoring mode can also be selected by pressing the BIT key. If the bit
monitoring mode was previously invoked, the DAT displays the last bit element
monitored. If the bit monitoring mode was not previously invoked, the DAT displays
the first element of the list. However, there may be a brief delay while the DAT
requests information from the controller. During the delay, the working screen will
display. See “Working Screen Operation” on page 7-14.
Monitoring and Editing
1. Press the INT or BIT key to enter the desired mode. The element number flashes
(if not protected).
2. Use the up/down key to scroll through the list of elements.
3. Press ENTER to select the element you want to edit. The element number
becomes steady and the data flashes if it is not protected.
Note:
If the element is protected, the enter key is ignored.
4. Use the up/down key to change the data. Bit values toggle between “ON” and
“OFF”. Integer values increment or decrement. Holding down the up/down key
causes the integer value to increment or decrement quickly.
If the data is protected or undefined, pressing the up/down key scrolls
Note:
to the next element in the list.
5. Press ENTER to accept the new data. Press ESC or INT/BIT to discard the new
data.
7-12
Using Trim Pots and the Data Access Tool (DAT)
F1 and F2 Functions
The function keys, F1 and F2, correspond to bits and can be used throughout the
control program as desired. They have no effect on bit or integer monitoring.
Each key has two corresponding bits in the DAT function file. The bits within the
DAT function file are shown in the table below.
Key
F1 Key
F2 Key
Bits
Address
Data Format
Type
User Program Access
Pressed
DAT:0/F1P
Binary
Status
Read/Write
Latched
DAT:0/F1L
Binary
Status
Read/Write
Pressed
DAT:0/F2P
Binary
Status
Read/Write
Latched
DAT:0/F2L
Binary
Status
Read/Write
F1 or F2 Key Pressed
The pressed bits (DAT:0/F1P and DAT:0/F2P) function as push-buttons and provide
current state of either the F1 or F2 key on the keypad. When the F1 or F2 key is
pressed, the DAT sets (1) the corresponding pressed key bit. When the F1 or F2 key is
not pressed, the DAT clears (0) the corresponding pressed key bit.
F1 or F2 Key Latched
The latched bits (DAT:0/F1L and DAT:0/F2L) function as latched push-buttons and
provide latched/toggle key functionality. When the F1 or F2 key is pressed, the DAT
sets (1) the corresponding latched key bit within the DAT Function File. When the F1
or F2 key is pressed a second time, the DAT clears (0) the corresponding latched key
bit.
7-13
MicroLogix 1500 Programmable Controllers User Manual
Working Screen Operation
Because the DAT is a communications device, its performance is affected by the scan
time of the controller. Occasionally, when there is a long scan time and the DAT is
waiting for information from the controller, the working screen is displayed. The
working screen consists of three dashes that move across the display from left to right.
While the working screen is displayed, key presses will not be recognized. Once the
DAT receives the data, it returns to its normal mode of operation.
You can minimize the effect of the working screen by adding an SVC instruction to
the control program. See “Service Communications (SVC)” on page 25-24.
Non-Existent Elements
When the DAT determines that an element number does not exist in the controller, the
element value displays as three dashes. If the protection bit for an element is
undefined, the DAT will assume that the element is unprotected.
Controller Faults
The DAT checks for controller faults every 10 seconds. When the DAT detects a
controller fault, the display shows “FL” in the element number field and the value of
the controller’s major fault word (S2:6) is displayed in the value field, as shown
below.
PROTECTED
f l 0020H
Note:
7-14
F1
F2
ESC
BIT
INT
ENTER
If an element value is being modified when the fault is detected, the fault
is stored until the modification is accepted or discarded. Then, the fault
will be displayed.
Using Trim Pots and the Data Access Tool (DAT)
Pressing ESC while the fault is being displayed returns the DAT to its previous mode.
The fault is not removed from the controller, just from the DAT display screen. The
fault that was on screen will not display again and cannot be “recalled”. If a new fault
is detected, it will be displayed. If the initial fault is cleared and returns at a later time,
the DAT will display the fault at that time.
Error Conditions
When the DAT detects an error in its own operation, it displays the error screen. The
error screen consists of “Err” and a two-digit error code, as shown below.
PROTECTED
F1
F2
ESC
BIT
INT
ENTER
The DAT can experience two different types of errors, internal errors and
communication errors. They are described in the following sections.
Internal DAT Errors
Internal DAT errors are non-recoverable. When the DAT experiences an internal error,
it displays the error screen, and the tool will not respond to any key presses. Remove
and re-install the DAT. If this does not clear the error, the DAT must be replaced.
Communication Errors
If the DAT experiences a communication error, the error message screen displays.
During these error conditions, the tool will respond to the up/down arrow key, the bit
and integer keys, and the ESC key. Pressing any of those keys clears the error
message. Any on-going element modifications are discarded.
7-15
MicroLogix 1500 Programmable Controllers User Manual
The DAT continually monitors the interface between the DAT and the controller to
ensure a good communication path. If the DAT loses communication with the
controller for more than three seconds, it generates an interface time-out error. The
DAT continues to attempt to re-establish communications. The error screen displays
until the DAT regains communications with the processor. All key presses are
ignored until the display clears.
DAT Error Codes
Error Code
00
1.
7-16
Description
Caused by
Recommended Action
Interface time-out
Communication traffic
Add SVC instructions to ladder program
01-02
Power-up test failure
Internal failure
Remove and re-insert the DAT. If failure
persists, replace the unit.
03 - 07
internal error
Internal failure
Remove and re-insert the DAT. If failure
persists, replace the unit.
08
processor owned1
Another device has ownership of the
controller
Release ownership by the other device
09
access denied
Cannot access that file because another
device has ownership
Release file ownership by the other
device
31-34
internal error
Internal failure
Remove and re-insert the DAT. If failure
persists, replace the unit.
This error can occur after a download in which communications configurations are changed. This error can be cleared by removing and
re-installing the DAT, or by cycling power to the controller.
Using Real Time Clock and Memory Modules
8
Using Real Time Clock and Memory
Modules
Three modules with different levels of functionality are available for use with the
MicroLogix 1500 controller.
Catalog Number
Function
1764-RTC
Real Time Clock
1764-MM1
Memory Module
1764-MM1RTC
Memory Module and Real Time Clock
Real Time Clock Operation
Removal/Insertion Under Power
At power-up or on detection of a real time clock being inserted, the controller
determines if a real time clock module is present. If a real time clock is present, its
values are written to the RTC Function File in the controller.
The real time clock module can be installed or removed at any time without risk of
damage to either the module or the controller. If a module is installed while the
MicroLogix 1500 is executing, the module will not be recognized until either a power
cycle occurs, or until the controller is placed in a non-executing mode (program mode
or fault condition).
Removal of the memory module is detected within one program scan. Removal of the
real time clock under power causes the controller to write zeros to the (RTC) Function
File.
8-1
MicroLogix 1500 Programmable Controllers User Manual
Real Time Clock Function File
The real time clock provides year, month, day of month, day of week, hour, minute,
and second information to the Real Time Clock (RTC) Function File in the controller.
The programming screen is shown below:
The parameters and their valid ranges are shown in the table below.
Feature
Address
Data Format
Range
Type
User Program
Access
YR - RTC Year
RTC:0.YR
word
1998 to 2097
status
read only
MON - RTC Month
RTC:0.MON
word
1 to 12
status
read only
DAY - RTC Day of Month
RTC:0.DAY
word
1 to 31
status
read only
HR - RTC Hours
RTC:0.HR
word
0 to 23 (military time)
status
read only
MIN - RTC Minutes
RTC:0.MIN
word
0 to 59
status
read only
SEC - RTC Seconds
RTC:0.SEC
word
0 to 59
status
read only
DOW - RTC Day of Week
RTC:0.DOW
word
0 to 6 (Sunday to Saturday)
status
read only
DS - Disabled
RTC:0/DS
binary
0 or 1
control
read/write
BL - RTC Battery Low
RTC:0/BL
binary
0 or 1
status
read only
8-2
Using Real Time Clock and Memory Modules
Writing Data to the Real Time Clock
When valid data is sent to the real time clock from the programming device, the new
values take effect immediately.
The real time clock does not allow you to write invalid date or time data.
Use the Disable Clock button in your programming device to disable the real time
clock before storing a module. This will decrease the drain on the battery during
storage.
RTC Battery Operation
The real time clock has an internal battery that is not replaceable. The RTC Function
File features a battery low indicator bit (RTC:0/BL), which shows the status of the
RTC battery. When the battery is low, the indicator bit is set (1). This means that the
battery will fail in less than 14 days, and the real time clock module needs to be
replaced. When the battery low indicator bit is clear (0), the battery level is
acceptable, or a real time clock is not attached.
!
ATTENTION: Operating with a low battery indication for more than
14 days may result in invalid RTC data.
8-3
MicroLogix 1500 Programmable Controllers User Manual
Memory Module Operation
More than just user back-up, the memory module supports the following features:
•
User Program and Data Back-up
•
Program Compare
•
Data File Protection
•
Memory Module Write Protection
•
Removal/Insertion Under Power
User Program and Data Back-up
The memory module provides a simple and flexible program/data transport
mechanism, allowing the user to update the program in the controller without the use
of a personal computer and programming software.
During transfers of a program to or from a memory module, the controller’s RUN
LED flashes.
Program Compare
The memory module also provides program security, allowing you to specify that if
the program stored in the memory module does not match the program in the
controller, the controller will not be able to enter an executing (run or test) mode. To
enable this feature, set the S:2/9 bit in the system status file. See “Memory Module
Program Compare” on page G-10 for more information.
Data File Protection
The memory module features the capability to specify which data files in the
controller are protected from the download procedure.
Note:
8-4
File protection is only functional if the processor does not have a
memory fault, and if the data file structure of the memory module
matches the data file structure within the controller. See“Protecting Data
Files During Download” on page 6-6.
Using Real Time Clock and Memory Modules
Memory Module Write Protection
The memory module supports write-once, read-many behavior. Write protection is
enabled using your programming software.
Important:
Once set, write protection cannot be removed. If a change needs to
be made to the control program stored in the memory module, the
same memory module cannot be re-used.
Removal/Insertion Under Power
The memory module can be installed or removed at any time without risk of damage
to either the memory module or the controller. If a memory module is installed while
the MicroLogix 1500 is executing, the memory module will not be recognized until
either a power cycle occurs, or until the controller is placed in a non-executing mode
(program mode or fault condition).
Removal of the memory module is detected within one program scan.
Memory Module Information File
The controller has a Memory Module Information (MMI) File which is updated with
data from the attached memory module. At power-up or on detection of a memory
module being inserted, the catalog number, series, revision, and type (memory
module and/or real time clock) are identified and written to the MMI file in the user
program. If a memory module and/or real time clock is not attached, zeros are written
to the MMI file.
The memory module function file programming screen is shown below:
8-5
MicroLogix 1500 Programmable Controllers User Manual
The parameters and their valid ranges are shown in the table below.
Feature
Address
Data Format
Type
User Program
Access
FT - Functionality Type
MMI:0.FT
word (INT)
status
read only
MP - Module Present
MMI:0/MP
binary (bit)
status
read only
WP - Write Protect
MMI:0/WP
binary (bit)
control
read only
FO - Fault Override
MMI:0/FO
binary (bit)
control
read only
LPC - Program Compare
MMI:0/LPC
binary (bit)
control
read only
LE - Load On Error
MMI:0/LE
binary (bit)
control
read only
LA - Load Always
MMI:0/LA
binary (bit)
control
read only
MB - Mode Behavior
MMI:0/MB
binary (bit)
control
read only
Functionality Type
This bit identifies the type of memory module installed:
8-6
•
1 = 1764-MM1 Memory Module
•
2 = 1764-RTC Real Time Clock
•
3 = 1764-MM1RTC Memory Module and Real Time Clock
Using Real Time Clock and Memory Modules
Module Present (MP)
The MP (Module Present) bit can be used throughout the user program to determine
when a memory module is present on the processor. This bit is updated once per scan,
provided the memory module is first recognized by the processor. To be recognized
by the processor, the memory module must be installed on the processor prior to
power-up or when it is in a non-executing mode. If a memory module is installed
when the processor is in an executing mode, it is not recognized. If the memory
module is removed during an executing mode, this bit will be cleared (0) at the end of
the next ladder scan.
Write Protect (WP)
When the WP (Write Protect) bit is set (1), the module is write-protected and the user
program and data within the memory module cannot be overwritten. When the WP bit
is cleared (0), the module is read/write.
Fault Override
The FO (Fault Override) bit shows the status of the fault override selection in the
memory module’s user program status file. It enables you to determine the value of
the selection without actually loading the user program from the memory module.
Important:
The memory module fault override selection in the Memory
Module Information (MMI) file does not determine the
controller’s operation. It merely displays the setting of the Fault
Override bit (S:1/8) in the memory module’s user program.
See “Fault Override At Power-Up” on page G-5 for more information.
8-7
MicroLogix 1500 Programmable Controllers User Manual
Load Program Compare
The LPC (Load Program Compare) bit shows the status of the load program compare
selection in the memory module’s user program status file. It enables you to
determine the value of the selection without actually loading the user program from
the memory module.
Important:
The memory module load program compare selection in the
Memory Module Information (MMI) file does not determine the
controller’s operation. It merely displays the setting of the Load
Program Compare bit (S:2/9) in the memory module’s user
program.
See “Memory Module Program Compare” on page G-10 for more information.
Load on Error
The LE (Load on Error) bit shows the status of the load on error selection in the
memory module’s user program status file. It enables you to determine the value of
the selection without actually loading the user program from the memory module.
See “Load Memory Module On Error Or Default Program” on page G-6 for more
information.
Load Always
The LA (Load Always) bit shows the status of the load always selection in the
memory module’s user program status file. It enables you to determine the value of
the selection without actually loading the user program from the memory module.
See “Load Memory Module Always” on page G-6 for more information.
Mode Behavior
The MB (Mode Behavior) bit shows the status of the mode behavior selection in the
memory module’s user program status file. It enables you to determine the value of
the selection without actually loading the user program from the memory module.
See “Power-Up Mode Behavior” on page G-7 for more information.
8-8
Using the High Speed Counter
9
Using the High Speed Counter
The MicroLogix 1500 has two 20 kHz high speed counters. Each counter has four
dedicated inputs that are isolated from other inputs on the base unit. HSC0 utilizes
inputs 0 through 3, and HSC1 utilizes inputs 4 through 7. Each counter is completely
independent and isolated from the other. HSC0 is used in this document to define how
the HSC works in the MicroLogix 1500 system, HSC1 is identical in functionality.
This chapter describes how to use the HSC function and also contains sections on the
HSL and RAC instructions, as follows:
•
“High Speed Counter (HSC) Function File” on page 9-2.
•
“HSL - High Speed Counter Load” on page 9-29.
•
“RAC - Reset Accumulated Value” on page 9-31.
9-1
MicroLogix 1500 Programmable Controllers User Manual
High Speed Counter (HSC) Function File
Within the RSLogix 500 Function File Folder, you see a HSC Function File with two
elements, HSC0 and HSC1. These elements provide access to HSC configuration
data, and also allows the control program access to all information pertaining to each
of the High Speed Counters.
Note:
9-2
NOTE: If the controller mode is run, the data within sub-element fields may
be changing.
Using the High Speed Counter
The HSC function, along with the PTO and PWM instructions, are different than most
other controller instructions. Their operation is performed by custom circuitry that
runs in parallel with the main system processor. This is necessary because of the high
performance requirements of these functions.
The HSC built into the MicroLogix 1500 is extremely versatile, the user can select or
configure each HSC for any one of eight (8) modes of operation. (Operating Modes
are discussed later in this chapter, see section “HSC Mode (MOD)” on page 9-18).
Some of the enhanced capabilities of the MicroLogix 1500 High Speed Counters are:
•
20 kHz operation
•
High speed direct control of outputs
•
32-bit signed integer data (count range of ± 2,147,483,647)
•
Programmable High and Low presets, and Overflow and Underflow setpoints
•
Automatic Interrupt processing based on accumulated count
•
On-line/run-time editable parameters (from the user control program)
The High Speed Counter function operates as described in the following diagram.
Overflow
+2,147,483,647 maximum
High Preset
0
Low Preset
Underflow
-2,147,483,647 minimum
9-3
MicroLogix 1500 Programmable Controllers User Manual
High Speed Counter Function File Sub-Elements Summary
Each HSC is comprised of 36 sub-elements. These sub-elements are either bit, word,
or long word structures that are used to provide control over the HSC function, or
provide HSC status information for use within the control program. Each of the subelements and their respective functions are described in this chapter. A summary of
the sub-elements is provided in the following table. All examples illustrate HSC0.
Terms and behavior for HSC1 are identical.
Table 9-1: High Speed Counter Function File (HSC:0 or HSC:1)
Sub-Element Description
PFN - Program File Number
ER - Error Code
UIX - User Interrupt Executing
UIE - User Interrupt Enable
UIL - User Interrupt Lost
UIP - User Interrupt Pending
FE - Function Enabled
AS - Auto Start
ED - Error Detected
CE - Counting Enabled
SP - Set Parameters
LPM - Low Preset Mask
HPM - High Preset Mask
UFM - Underflow Mask
OFM - Overflow Mask
LPI - Low Preset Interrupt
HPI - High Preset Interrupt
UFI - Underflow Interrupt
OFI - Overflow Interrupt
LPR - Low Preset Reached
HPR - High Preset Reached
DIR - Count Direction
UF - Underflow
OF - Overflow
MD - Mode Done
CD - Count Down
9-4
Address
HSC:0.PFN
HSC:0.ER
HSC:0/UIX
HSC:0/UIE
HSC:0/UIL
HSC:0/UIP
HSC:0/FE
HSC:0/AS
HSC:0/ED
HSC:0/CE
HSC:0/SP
HSC:0/LPM
HSC:0/HPM
HSC:0/UFM
HSC:0/OFM
HSC:0/LPI
HSC:0/HPI
HSC:0/UFI
HSC:0/OFI
HSC:0/LPR
HSC:0/HPR
HSC:0/DIR
HSC:0/UF
HSC:0/OF
HSC:0/MD
HSC:0/CD
Data Format
word (INT)
word (INT)
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
bit
HSC
Modes1
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 to 7
0 or 1
2 to 7
Type
control
status
status
control
status
status
control
control
status
control
control
control
control
control
control
status
status
status
status
status
status
status
status
status
status
status
User Program For More
Access
Information
read only
read only
read only
read/write
read/write
read only
read/write
read only
read only
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read only
read only
read only
read/write
read/write
read/write
read only
9-5
9-6
9-9
9-8
9-10
9-9
9-6
9-7
9-7
9-7
9-8
9-10
9-12
9-14
9-15
9-11
9-12
9-14
9-16
9-11
9-13
9-16
9-13
9-15
9-17
9-17
Using the High Speed Counter
Table 9-1: High Speed Counter Function File (HSC:0 or HSC:1)
Sub-Element Description
CU - Count Up
MOD - HSC Mode
ACC - Accumulator
HIP - High Preset
LOP - Low Preset
OVF - Overflow
UNF - Underflow
OMB - Output Mask Bits
HPO - High Preset Output
LPO - Low Preset Output
1.
Address
HSC:0/CU
HSC:0.MOD
HSC:0.ACC
HSC:0.HIP
HSC:0.LOP
HSC:0.OVF
HSC:0.UNF
HSC:0.OMB
HSC:0.HPO
HSC:0.LPO
Data Format
bit
word (INT)
long word (32-bit INT)
long word (32-bit INT)
long word (32-bit INT)
long word (32-bit INT)
long word (32-bit INT)
word (16-bit binary)
word (16-bit binary)
word (16-bit binary)
HSC
Modes1
0 to 7
0 to 7
0 to 7
0 to 7
2 to 7
0 to 7
2 to 7
0 to 7
0 to 7
2 to 7
Type
User Program For More
Access
Information
status
control
control
control
control
control
control
control
control
control
read only
read only
read/write
read/write
read/write
read/write
read/write
read only
read/write
read/write
9-17
9-18
9-24
9-25
9-25
9-26
9-26
9-27
9-28
9-28
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
n/a = not applicable
HSC Function File Sub-Elements
All examples illustrate HSC0. Terms and behavior for HSC1 are identical.
Program File Number (PFN)
Sub-Element Description
PFN - Program File Number
1.
Address
HSC:0.PFN
Data Format
word (INT)
HSC Modes1
0 to 7
Type
User Program Access
control
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The PFN (Program File Number) variable defines which subroutine is called
(executed) when the HSC0 count to High Preset or Low Preset through Overflow or
Underflow. The integer value of this variable defines which program file will run at
that time. A valid subroutine file is any program file (3 to 255).
The subroutine file identified in the PFN variable is not a special file within the
controller, it is programmed and operates the same as any other program file. From
the control program perspective it is unique, in that it is automatically scanned based
on the configuration of the HSC.
See also: “Interrupt Latency” on page 23-5.
9-5
MicroLogix 1500 Programmable Controllers User Manual
Error Code (ER)
Sub-Element Description
ER - Error Code
1.
Address
HSC:0.ER
Data Format
word (INT)
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The ERs (Error Codes) detected by the HSC sub-system will be displayed in this
word. Errors include:
Table 9-2: HSC Error Codes
Error Code
1
Name
Invalid File Number
Mode
n/a
2
3
Invalid Mode
Invalid High Preset
4
Invalid Overflow
n/a
0,1
2 to 7
0 to 7
Description
Interrupt (program) file identified in HSC:0.PFN is
less than 3, greater than 255, or does not exist
Invalid Mode
High preset is less than or equal to zero (0)
High preset is less than or equal to low preset
High preset is greater than overflow
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
Function Enabled (FE)
Sub-Element Description
FE - Function Enabled
1.
Address
HSC:0/FE
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The FE (Function Enabled) is a status/control bit that defines when the HSC interrupt
is enabled, and that interrupts generated by the HSC will be processed based on their
priority within the MicroLogix 1500 system.
This bit can be controlled by the user program, or will be automatically set by the
HSC sub-system if auto start is enabled.
See also: “Priority of User Interrupts” on page 23-4.
9-6
Using the High Speed Counter
Auto Start (AS)
Sub-Element Description
AS - Auto Start
1.
Address
HSC:0/AS
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The AS (Auto Start) is a control bit that can be used in the control program. The auto
start bit is configured with the programming device, and stored as part of the user
program. The auto start bit defines if the HSC function will automatically start
whenever the MicroLogix 1500 controller enters any run or test mode.
Error Detected (ED)
Sub-Element Description
ED - Error Detected
1.
Address
HSC:0/ED
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The ED (Error Detected) flag is a status bit that can be used in the control program to
detect if an error is present in the HSC sub-system. The most common type of error
that this bit represents is a configuration error. When this bit is set (1) the user should
look at the specific error code in parameter HSC:0.ER.
This bit is controlled by the MicroLogix 1500 system, and will be set and cleared
automatically.
Counting Enabled (CE)
Sub-Element Description
CE - Counting Enabled
1.
Address
HSC:0/CE
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The CE (Counting Enabled) control bit is used to enable or disable the High Speed
Counter. When set (1), counting is enabled, when clear (0, default) counting is
disabled. If this bit is disabled while the counter is running, the accumulated value is
held, if the bit is then set counting will resume.
This bit is controlled by the user program, and retains its value through a power cycle.
9-7
MicroLogix 1500 Programmable Controllers User Manual
Set Parameters (SP)
Sub-Element Description
SP - Set Parameters
1.
Address
HSC:0/SP
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The SP (Set Parameters) control bit is used to load new variables to the HSC subsystem. When an OTE instruction with the address of HSC:0/SP is solved true (off-toon rung transition), all configuration variables currently stored in the HSC function,
will be checked, and loaded into the HSC sub-system. The HSC sub-system will then
operate based on those newly loaded settings.
This bit is controlled by the user program, and retains its value through a power cycle.
It is up to the user program to set and clear this bit. SP can be toggled while the HSC
is running and no counts will be lost.
User Interrupt Enable (UIE)
Sub-Element Description
UIE - User Interrupt Enable
1.
Address
HSC:0/UIE
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UIE (User Interrupt Enable) bit is used to enable or disable HSC subroutine
processing. This bit must be set (1) if the user wants the controller to process the HSC
subroutine when any of the following conditions exist:
• Low preset reached
• High preset reached
• Overflow condition - count up through the overflow value
• Underflow condition - count down through the underflow value
If this bit is cleared (0), the HSC sub-system will not automatically scan the HSC
subroutine. This bit can be controlled from the user program (using the OTE, UIE, or
UID instructions).
ATTENTION: If you enable interrupts during the program scan via
an OTL, OTE, or UIE, this instruction must be the last instruction
executed on the rung (last instruction on last branch). It is
recommended this be the only output instruction on the rung.
!
9-8
Using the High Speed Counter
User Interrupt Executing (UIX)
Sub-Element Description
Address
UIX - User Interrupt Executing HSC:0/UIX
1.
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UIX (User Interrupt Executing) bit is set (1) whenever the HSC sub-system
begins processing the HSC subroutine due to any of the following conditions:
•
Low preset reached
•
High preset reached
•
Overflow condition - count up through the overflow value
•
Underflow condition - count down through the underflow value
The HSC sub-system will clear (0) the UIX bit when the controller completes its
processing of the HSC subroutine.
The HSC UIX bit can be used in the control program as conditional logic to detect if
an HSC interrupt is executing.
User Interrupt Pending (UIP)
Sub-Element Description
UIP - User Interrupt Pending
1.
Address
HSC:0/UIP
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UIP (User Interrupt Pending) is a status flag that represents an interrupt is
pending. This status bit can be monitored, or used for logic purposes in the control
program if you need to determine when a subroutine cannot be executed immediately.
This bit is controlled by the MicroLogix 1500 system, and will be set and cleared
automatically.
9-9
MicroLogix 1500 Programmable Controllers User Manual
User Interrupt Lost (UIL)
Sub-Element Description
UIL - User Interrupt Lost
1.
Address
HSC:0/UIL
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UIL (User Interrupt Lost) is a status flag that represents an interrupt has been
lost. The MicroLogix 1500 can process 1 active, and maintain up to 2 pending user
interrupt conditions.
This bit is set by the MicroLogix 1500. It is up to the control program to utilize, track
if necessary, and clear the lost condition.
Low Preset Mask (LPM)
Sub-Element Description
LPM - Low Preset Mask
1.
Address
HSC:0/LPM
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The LPM (Low Preset Mask) control bit is used to enable (allow) or disable (not
allow) a low preset interrupt from occurring. If this bit is clear (0), and a Low Preset
Reached condition is detected by the HSC, the HSC user interrupt will not be
executed.
This bit is controlled by the user program, and retains its value through a power cycle.
It is up to the user program to set and clear this bit.
9-10
Using the High Speed Counter
Low Preset Interrupt (LPI)
Sub-Element Description
LPI - Low Preset Interrupt
1.
Address
HSC:0/LPI
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The LPI (Low Preset Interrupt) status bit will be set (1) when the HSC accumulator
reaches the low preset value and the HSC interrupt has been triggered. This bit can be
used in the control program to identify that the low preset condition caused the HSC
interrupt. If the control program needs to perform any specific control action based on
the low preset, this bit would be used as conditional logic.
This bit can be cleared (0) by the control program, and will also be cleared by the
HSC sub-system whenever these conditions are detected:
•
High Preset Interrupt executes
•
Underflow Interrupt executes
•
Overflow Interrupt executes
•
Controller enters an executing mode
Low Preset Reached (LPR)
Sub-Element Description
LPR - Low Preset Reached
1.
Address
HSC:0/LPR
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The LPR (Low Preset Reached) status flag is set (1) by the HSC sub-system whenever
the accumulated value (HSC:0.ACC) is less than or equal to the low preset variable
(HSC:0.LOP).
This bit is updated continuously by the HSC sub-system whenever the controller is in
an executing mode.
9-11
MicroLogix 1500 Programmable Controllers User Manual
High Preset Mask (HPM)
Sub-Element Description
HPM - High Preset Mask
1.
Address
HSC:0/HPM
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The HPM (High Preset Mask) control bit is used to enable (allow) or disable (not
allow) a high preset interrupt from occurring. If this bit is clear (0), and a High Preset
Reached condition is detected by the HSC, the HSC user interrupt will not be
executed.
This bit is controlled by the user program, and retains its value through a power cycle.
It is up to the user program to set and clear this bit.
High Preset Interrupt (HPI)
Sub-Element Description
HPI - High Preset Interrupt
1.
Address
HSC:0/HPI
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The HPI (High Preset Interrupt) status bit will be set (1) when the HSC accumulator
reaches the high preset value and the HSC interrupt has been triggered. This bit can be
used in the control program to identify that the high preset condition caused the HSC
interrupt. If the control program needs to perform any specific control action based on
the high preset, this bit would be used as conditional logic.
This bit can be cleared (0) by the control program, and will also be cleared by the
HSC sub-system whenever these conditions are detected:
9-12
•
Low Preset Interrupt executes
•
Underflow Interrupt executes
•
Overflow Interrupt executes
•
Controller enters an executing mode
Using the High Speed Counter
High Preset Reached (HPR)
Sub-Element Description
HPR - High Preset Reached
1.
Address
HSC:0/HPR
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The HPR (High Preset Reached) status flag is set (1) by the HSC sub-system
whenever the accumulated value (HSC:0.ACC) is greater than or equal to the high
preset variable (HSC:0.HIP).
This bit is updated continuously by the HSC sub-system whenever the controller is in
an executing mode.
Underflow (UF)
Sub-Element Description
UF - Underflow
1.
Address
HSC:0/UF
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UF (Underflow) status flag is set (1) by the HSC sub-system whenever the
accumulated value (HSC:0.ACC) has counted through the underflow variable
(HSC:0.UNF).
This bit is transitional, and is set by the HSC sub-system. It is up to the control
program to utilize, track if necessary, and clear (0) the underflow condition.
Underflow conditions will not generate a controller fault.
9-13
MicroLogix 1500 Programmable Controllers User Manual
Underflow Mask (UFM)
Sub-Element Description
UFM - Underflow Mask
1.
Address
HSC:0/UFM
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UFM (Underflow Mask) control bit is used to enable (allow) or disable (not
allow) a underflow interrupt from occurring. If this bit is clear (0), and a Underflow
Reached condition is detected by the HSC, the HSC user interrupt will not be
executed.
This bit is controlled by the user program, and retains its value through a power cycle.
It is up to the user program to set and clear this bit.
Underflow Interrupt (UFI)
Sub-Element Description
UFI - Underflow Interrupt
1.
Address
HSC:0/UFI
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The UFI (Underflow Interrupt) status bit will be set (1) when the HSC accumulator
counts through the underflow value and the HSC interrupt has been triggered. This bit
can be used in the control program to identify that the underflow condition caused the
HSC interrupt. If the control program needs to perform any specific control action
based on the underflow, this bit would be used as conditional logic.
This bit can be cleared (0) by the control program, and will also be cleared by the
HSC sub-system whenever these conditions are detected:
9-14
•
Low Preset Interrupt executes
•
High Preset Interrupt executes
•
Overflow Interrupt executes
•
Controller enters an executing mode
Using the High Speed Counter
Overflow (OF)
Sub-Element Description
OF - Overflow
1.
Address
HSC:0/OF
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The OF (Overflow) status flag is set (1) by the HSC sub-system whenever the
accumulated value (HSC:0.ACC) has counted through the overflow variable
(HSC:0.OF).
This bit is transitional, and is set by the HSC sub-system. It is up to the control
program to utilize, track if necessary, and clear (0) the overflow condition.
Overflow conditions will not generate a controller fault.
Overflow Mask (OFM)
Sub-Element Description
OFM - Overflow Mask
1.
Address
HSC:0/OFM
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
control
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The OFM (Overflow Mask) control bit is used to enable (allow) or disable (not allow)
an overflow interrupt from occurring. If this bit is clear (0), and an overflow reached
condition is detected by the HSC, the HSC user interrupt will not be executed.
This bit is controlled by the user program, and retains its value through a power cycle.
It is up to the user program to set and clear this bit.
9-15
MicroLogix 1500 Programmable Controllers User Manual
Overflow Interrupt (OFI)
Sub-Element Description
OFI - Overflow Interrupt
1.
Address
HSC:0/OFI
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The OFI (Overflow Interrupt) status bit will be set (1) when the HSC accumulator
counts through the overflow value and the HSC interrupt has been triggered. This bit
can be used in the control program to identify that the overflow variable caused the
HSC interrupt. If the control program needs to perform any specific control action
based on the overflow, this bit would be used as conditional logic.
This bit can be cleared (0) by the control program, and will also be cleared by the
HSC sub-system whenever these conditions are detected:
•
Low Preset Interrupt executes
•
High Preset Interrupt executes
•
Underflow Interrupt executes
•
Controller enters an executing mode
Count Direction (DIR)
Sub-Element Description
DIR - Count Direction
1.
Address
HSC:0/DIR
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The DIR (Count Direction) status flag is controlled by the HSC sub-system. When the
HSC accumulator counts up, the direction flag will be set (1). Whenever the HSC
accumulator counts down, the direction flag will be cleared (0).
If the accumulated value stops, the direction bit will retain its value. The only time the
direction flag will change is when the accumulated count reverses.
This bit is updated continuously by the HSC sub-system whenever the controller is in
a run mode.
9-16
Using the High Speed Counter
Mode Done (MD)
Sub-Element Description
MD - Mode Done
1.
Address
HSC:0/MD
Data Format
bit
HSC Modes1
0 or 1
Type
User Program Access
status
read/write
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The MD (Mode Done) status flag is set (1) by the HSC sub-system when the HSC is
configured for Mode 0 or Mode 1 behavior, and the accumulator counts up to the
High Preset.
Count Down (CD)
Sub-Element Description
CD - Count Down
1.
Address
HSC:0/CD
Data Format
bit
HSC Modes1
2 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The CD (Count Down) bit is used with the bidirectional counters (modes 2 to 7). If
the CE bit is set, the CD bit is set (1). If the CE bit is clear, the CD bit is cleared (0).
Count Up (CU)
Sub-Element Description
CU - Count Up
1.
Address
HSC:0/CU
Data Format
bit
HSC Modes1
0 to 7
Type
User Program Access
status
read only
For Mode descriptions, see “HSC Mode (MOD)” on page 9-18.
The CU (Count Up) bit is used with all of the HSCs (modes 0 to 7). If the CE bit is
set, the CU bit is set (1). If the CE bit is clear, the CU bit is cleared (0).
9-17
MicroLogix 1500 Programmable Controllers User Manual
HSC Mode (MOD)
Sub-Element Description
MOD - HSC Mode
Address
HSC:0.MOD
Data Format
word (INT)
Type
control
User Program Access
read only
The MOD (Mode) variable sets the High Speed Counter to one of 8 types of
operation. This integer value is configured through the programming device, and is
accessible in the control program as a read-only variable.
Table 9-3: HSC Operating Modes
Mode Number
Type
0
Up Counter - The accumulator is immediately cleared (0) when it reaches the high
preset. A low preset cannot be defined in this mode.
1
Up Counter with external reset and hold - The accumulator is immediately cleared (0)
when it reaches the high preset. A low preset cannot be defined in this mode.
2
Counter with external direction
3
Counter with external direction, reset, and hold
4
Two input counter (up and down)
5
Two input counter (up and down) with external reset and hold
6
Quadrature counter (phased inputs A and B)
7
Quadrature counter (phased inputs A and B) with external reset and hold
HSC Mode 0 - Up Counter
Table 9-4: HSC Mode 0 Examples
Input
I1:0.0/0 (HSC0)
Terminals I1:0.0/4 (HSC1)
Function
Count
Example 1 °
Example 2 ° on (1) ² off (0)
I1:0.0/1 (HSC0)
I1:0.0/5 (HSC1)
Not Used
I1:0.0/2 (HSC0)
I1:0.0/6 (HSC1)
Not Used
I1:0.0/3 (HSC0)
I1:0.0/7 (HSC1)
Not Used
CE
Bit
Comments
on (1) HSC Accumulator + 1 count
off (0) Hold accumulator value
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
9-18
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
Using the High Speed Counter
HSC Mode 1 - Up Counter with External Reset and Hold
Table 9-5: HSC Mode 1 Examples
Input
I1:0.0/0 (HSC0)
Terminals I1:0.0/4 (HSC1)
Function
Count
Example 1 °
I1:0.0/1 (HSC0)
I1:0.0/5 (HSC1)
Not Used
Example 2
Example3
Example 4
on ² off
(1)
(0)
Example 5
I1:0.0/2 (HSC0) I1:0.0/3 (HSC0)
CE
Comments
I1:0.0/6 (HSC1) I1:0.0/7 (HSC1)
Bit
Reset
Hold
on ² off
off on (1) HSC Accumulator + 1 count
(1)
(0)
(0)
on ² off
on
Hold accumulator value
(1)
(0)
(1)
on ² off
off (0) Hold accumulator value
(1)
(0)
on ² off
Hold accumulator value
(1)
(0)
Clear accumulator (=0)
°
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
HSC Mode 2 - Counter with External Direction
Table 9-6: HSC Mode 2 Examples
Input
I1:0.0/0 (HSC0)
Terminals I1:0.0/4 (HSC1)
Function
Count
Example 1 °
Example 2 °
I1:0.0/1 (HSC0) I1:0.0/2 (HSC0)
I1:0.0/5 (HSC1) I1:0.0/6 (HSC1)
Direction
Not Used
off
(0)
on
(1)
Example3
I1:0.0/3 (HSC0)
I1:0.0/7 (HSC1)
Not Used
CE
Bit
Comments
on (1) HSC Accumulator + 1 count
on (1) HSC Accumulator - 1 count
off (0) Hold accumulator value
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
9-19
MicroLogix 1500 Programmable Controllers User Manual
HSC Mode 3 - Counter with External Direction, Reset, and Hold
Table 9-7: HSC Mode 3 Examples
Input
I1:0.0/0 (HSC0)
Terminals I1:0.0/4 (HSC1)
Function
Count
Example 1 °
I1:0.0/1 (HSC0) I1:0.0/2 (HSC0) I1:0.0/3 (HSC0)
CE
Comments
I1:0.0/5 (HSC1) I1:0.0/6 (HSC1) I1:0.0/7 (HSC1)
Bit
Direction
Reset
Hold
off
on ² off
off on (1) HSC Accumulator + 1 count
(0)
(1)
(0)
(0)
Example 2 °
on
on ² off
off on (1) HSC Accumulator - 1 count
(1)
(1)
(0)
(0)
Example3
on ² off
on
Hold accumulator value
(1)
(0)
(1)
Example 4
on ² off
off (0) Hold accumulator value
(1)
(0)
Example 5
on ² off
on ² off
Hold accumulator value
(1)
(0)
(1)
(0)
Example 6
Clear accumulator (0=)
°
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
HSC Mode 4 - Two Input Counter (up and down)
Table 9-8: HSC Mode 4 Examples
Input
I1:0.0/0 (HSC0)
Terminals I1:0.0/4 (HSC1)
Function
Count Up
Example 1 °
Example 2
I1:0.0/1 (HSC0) I1:0.0/2 (HSC0)
I1:0.0/5 (HSC1) I1:0.0/6 (HSC1)
Count Down
Not Used
on ² off
(1)
(0)
on ² off °
(1)
(0)
Example3
I1:0.0/3 (HSC0)
I1:0.0/7 (HSC1)
Not Used
CE
Bit
Comments
on (1) HSC Accumulator + 1 count
on (1) HSC Accumulator - 1 count
off (0) Hold accumulator value
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
9-20
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
Using the High Speed Counter
HSC Mode 5 - Two Input Counter (up and down) with External Reset and Hold
Table 9-9: HSC Mode 5 Examples
Input
I1:0.0/0 (HSC0)
Terminals I1:0.0/4 (HSC1)
Function
Count
Example 1 °
Example 2
on ² off
(1)
(0)
Example3
Example 4
Example 5
on ² off
(1)
(0)
Example 6
I1:0.0/1 (HSC0) I1:0.0/2 (HSC0) I1:0.0/3 (HSC0)
CE
Comments
I1:0.0/5 (HSC1) I1:0.0/6 (HSC1) I1:0.0/7 (HSC1)
Bit
Direction
Reset
Hold
on ² off
on ² off
off on (1) HSC Accumulator + 1 count
(1)
(0)
(1)
(0)
(0)
on ² off
off on (1) HSC Accumulator - 1 count
°
(1)
(0)
(0)
on ² off
on
Hold accumulator value
(1)
(0)
(1)
on ² off
off (0) Hold accumulator value
(1)
(0)
on ² off
Hold accumulator value
(1)
(0)
Clear accumulator (0=)
°
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
9-21
MicroLogix 1500 Programmable Controllers User Manual
Using the Quadrature Encoder
The Quadrature Encoder is used for determining direction of rotation and position for
rotating, such as a lathe. The Bidirectional Counter counts the rotation of the
Quadrature Encoder.
The following figure shows a quadrature encoder connected to inputs 0, 1, and 2. The
count direction is determined by the phase angle between A and B. If A leads B, the
counter increments. If B leads A, the counter decrements.
The counter can be reset using the Z input. The Z outputs from the encoders typically
provide one pulse per revolution.
A
Input 0
Input 1
B
Quadrature Encoder
Input 2
Z
(Reset input)
Forward Rotation
Reverse Rotation
A
B
1
Count
9-22
2
3
2
1
Using the High Speed Counter
HSC Mode 6 - Quadrature Counter (phased inputs A and B)
Table 9-10: HSC Mode 6 Examples
Input
Terminals
Function
I1:0.0/0 (HSC0)
I1:0.0/4 (HSC1)
Count A
Example 11 °
²
Example 22
Example3
Example 4
I1:0.0/1 (HSC0) I1:0.0/2 (HSC0)
I1:0.0/5 (HSC1) I1:0.0/6 (HSC1)
Count B
Not Used
off
(0)
off
(0)
off
(0)
I1:0.0/3 (HSC0)
I1:0.0/7 (HSC1)
Not Used
CE
Bit
Comments
on (1) HSC Accumulator + 1 count
on (1) HSC Accumulator - 1 count
Hold accumulator value
on
(1)
Hold accumulator value
Example 5
on
(1)
Example 6
Hold accumulator value
off (0) Hold accumulator value
1. Count input A leads count input B.
2. Count input B leads count input A.
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
9-23
MicroLogix 1500 Programmable Controllers User Manual
HSC Mode 7 - Quadrature Counter (phased inputs A and B) With External Reset and Hold
Table 9-11: HSC Mode 7 Examples
Input
Terminals
Function
I1:0.0/0 (HSC0)
I1:0.0/4 (HSC1)
Count A
I1:0.0/1 (HSC0) I1:0.0/2 (HSC0) I1:0.0/3 (HSC0)
CE
Comments
I1:0.0/5 (HSC1) I1:0.0/6 (HSC1) I1:0.0/7 (HSC1)
Bit
Count B
Z reset
Hold
1 °
off
off on (1) HSC Accumulator + 1 count
Example 1
(0)
(0)
off
off
off on (1) HSC Accumulator - 1 count
²
Example 22
(0)
(0)
(0)
Example3
off
on
Reset accumulator to zero
² off
(0)
(0)
(1)
Example 4
on
Hold accumulator value
(1)
Example 5
on
Hold accumulator value
(1)
Example 6
off
on
Hold accumulator value
(0)
(1)
Example 7
off
off (0) Hold accumulator value
(0)
1. Count input A leads count input B.
2. Count input B leads count input A.
Blank cells = don’t care.
° = rising edge
² = falling edge
Note:
Inputs I1:0.0/0 through I1:0.0/7 are available for use as inputs to other
functions regardless of the HSC being used.
Accumulator (ACC)
Sub-Element Description
ACC - Accumulator
Address
HSC:0.ACC
Data Format
long word (32-bit INT)
Type
control
User Program Access
read/write
The ACC (Accumulator) contains the number of counts detected by the HSC subsystem. If either mode 0 or mode 1 is configured, the value of the software
accumulator will be cleared (0) when a high preset is reached, or when an overflow
condition is detected.
9-24
Using the High Speed Counter
High Preset (HIP)
Sub-Element Description
HIP - High Preset
Address
HSC:0.HIP
Data Format
long word (32-bit INT)
Type
control
User Program Access
read/write
The HIP (High Preset) is the upper setpoint (in counts) that defines when the HSC
sub-system will generate an interrupt. To load data into the high preset, the control
program must do one of the following:
•
Toggle (low to high) the Set Parameters (HSC:0/SP) control bit. When the SP bit
is toggled high, the data currently stored in the HSC function file is transferred/
loaded into the HSC sub-system.
•
Load new HSC parameters using the HSL instruction. See “HSL - High Speed
Counter Load” on page 9-29.
The data loaded into the high preset must be less than or equal to the data resident in
the overflow (HSC:0.OVF) parameter or an HSC error will be generated.
Low Preset (LOP)
Sub-Element Description
LOP - Low Preset
Address
HSC:0.LOP
Data Format
long word (32-bit INT)
Type
control
User Program Access
read/write
The LOP (Low Preset) is the lower setpoint (in counts) that defines when the HSC
sub-system will generate an interrupt. To load data into the low preset, the control
program must do one of the following:
•
Toggle (low to high) the Set Parameters (HSC:0/SP) control bit. When the SP bit
is toggled high, the data currently stored in the HSC function file is transferred/
loaded into the HSC sub-system.
•
Load new HSC parameters using the HSL instruction. See “HSL - High Speed
Counter Load” on page 9-29.
The data loaded into the low preset must greater than or equal to the data resident in
the underflow (HSC:0.UNF) parameter, or an HSC error will be generated. (If the
underflow and low preset values are negative numbers, the low preset must be a
number with a smaller absolute value.)
9-25
MicroLogix 1500 Programmable Controllers User Manual
Overflow (OVF)
Sub-Element Description
OVF - Overflow
Address
HSC:0.OVF
Data Format
long word (32-bit INT)
Type
control
User Program Access
read/write
The OVF (Overflow) defines the upper count limit for the counter. If the counters
accumulated value increments past the value specified in this variable, an overflow
interrupt is generated, and the HSC sub-system rolls the accumulator over to the
underflow value, the counter continues counting from the underflow value (counts are
not lost in this transition). The user can specify any value for the overflow position,
provided it is greater than the underflow value, and falls between
-2,147,483,648 and 2,147,483,647.
To load data into the overflow variable, the control program must toggle (low to high)
the Set Parameters (HSC:0.0/SP) control bit. When the SP bit is toggled high, the data
currently stored in the HSC function file is transferred/loaded into the HSC subsystem.
Note:
Data loaded into the overflow variable must be greater than the data resident
in the high preset (HSC:0.HIP) or an HSC error will be generated.
Underflow (UNF)
Sub-Element Description
UNF - Underflow
Address
HSC:0.UNF
Data Format
long word (32-bit INT)
Type
control
User Program Access
read/write
The UNF (Underflow) defines the lower count limit for the counter. If the counters
accumulated value decrements past the value specified in this variable, an underflow
interrupt is generated, and the HSC sub-system resets the accumulated value to the
overflow value, the counter then begins counting from the overflow value (counts are
not lost in this transition). The user can specify any value for the underflow position,
provided it is less than the overflow value, and falls between
-2,147,483,648 and 2,147,483,647.
To load data into the underflow variable, the control program must toggle (low to
high) the Set Parameters (HSC:0.0/SP) control bit. When the SP bit is toggled high,
the data currently stored in the HSC function file is transferred/loaded into the HSC
sub-system.
Note:
9-26
Data loaded into the underflow variable must be less than the data resident in
the low preset (HSC:0.LOP) or an HSC error will be generated?
Using the High Speed Counter
Output Mask Bits (OMB)
Sub-Element Description
OMB - Output Mask Bits
Address
HSC:0.OMB
Data Format
word (16-bit binary)
Type
control
User Program Access
read only
The OMB (Output Mask Bits) define what outputs on the MicroLogix 1500 base can
be directly controlled by the high speed counter. The HSC sub-system has the ability
to directly (without control program interaction) turn outputs ON or OFF based on the
HSC accumulator reaching the High or Low presets. The bit pattern stored in the
OMB variable will define which outputs are controlled by the HSC, and which
outputs are not controlled by the HSC.
The bit pattern of the OMB variable directly corresponds to the output bits on the
MicroLogix 1500 base unit. Bits that are set (1) are enabled and can be turned on or
off by the HSC sub-system, bits that are clear (0) can not be turned on or off by the
HSC sub-system. The mask bit pattern can be configured only during initial setup.
The table below illustrates this relationship:
Table 9-12: Affect of HSC Output Mask on Base Unit Outputs
Output Address
15
14
13
12
HSC:0.HPO (high preset output)
11
0
HSC:0.OMB (output mask)
1
O0:0.0 (MicroLogix 1500 Base Unit
Outputs)
0
16-Bit Signed Integer Data Word
10 9
8
7
6
5
4
1
1
0
1
0
0
1
0
0
0
0
1
1
1
0
0
1
3
1
2
0
1
0
0
1
0
0
1
1
0
1
The outputs shown in the black boxes are the outputs under the control of the HSC
sub-system. The mask defines which outputs can be controlled. The high preset
output or low preset output values (HPO or LPO) define if each output is either ON
(1) or OFF (0). Another way to view this is that the high or low preset output is
written through the output mask, with the output mask acting like a filter.
The bits in the gray boxes are unused. The first 12 bits of the mask word are used and
the remaining mask bits are not functional because the do not correlate to any
physical outputs on the base unit.
The mask bit pattern can be configured only during initial setup.
9-27
MicroLogix 1500 Programmable Controllers User Manual
High Preset Output (HPO)
Sub-Element Description
HPO - High Preset Output
Address
HSC:0.HPO
Data Format
word (16-bit binary)
Type
control
User Program Access
read/write
The HPO (High Preset Output) defines the state (1 = ON or 0 = OFF) of the outputs
on the MicroLogix 1500 base when the high preset is reached. See “Output Mask Bits
(OMB)” on page 9-27 for more information on how to directly turn outputs on or off
based on the high preset being reached.
The high output bit pattern can be configured during initial setup, or while the
controller is operating. Use the HSL instruction or the SP bit to load the new
parameters while the controller is operating.
Low Preset Output (LPO)
Sub-Element Description
LPO - Low Preset Output
Address
HSC:0.LPO
Data Format
word (16-bit binary)
Type
control
User Program Access
read/write
The LPO (Low Preset Output) defines the state (1 = “on”, 0 = “off”) of the outputs on
the MicroLogix 1500 base when the low preset is reached. See “Output Mask Bits
(OMB)” on page 9-27 for more information on how to directly turn outputs on or off
based on the low preset being reached.
The low output bit pattern can be configured during initial setup, or while the
controller is operating. Use the HSL instruction or the SP bit to load the new
parameters while the controller is operating.
9-28
Using the High Speed Counter
HSL - High Speed Counter Load
Instruction Type: output
HSL
HSL
High Speed Counter Load
HSC Number
HSC0
High Preset
N7:0
Low Preset
N7:1
Output High Source
N7:2
Output Low Source
N7:3
Table 9-13: Execution Time for the HSL Instruction
Data Size
word
long word
When Rung Is:
True
False
41.85 µs
0.00 µs
42.95µs
0.00 µs
The HSL (High Speed Load) instruction allows the high and low presets, and high
and low output source to be applied to a high speed counter. These parameters are
described below:
•
Counter Number - Specifies which high speed counter is being used; 0 = HSC0
and 1 = HSC1.
•
High Preset - Specifies the value in the high preset register. The data ranges for the
high preset are -32786 to 32767 (word) and -2,147,483,648 to 2,147,483,647
(long word).
•
Low Preset - Specifies the value in the low preset register. The data ranges for the
low preset are -32786 to 32767 (word) and -2,147,483,648 to 2,147,483,647 (long
word).
•
Output High Source - Specifies the value in the output high register. The data
range for the output high source is from 0 to FFFF.
•
Output Low Source - Specifies the value in the output low register. The data range
for the output low source is from 0 to FFFF.
9-29
MicroLogix 1500 Programmable Controllers User Manual
Valid Addressing Modes and File Types are shown below:
Table 9-14: HSL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Counter
Number
High Preset
Low Preset
Output High
Source
Output Low
Source
9-30
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CSF - Comms
IOS - I/O
Immediate
Direct
Indirect
Element
Bit
Word
Long Word
Data Files
•
• •
• •
• • • •
• • • •
• • •
• • •
• •
• •
• •
• • • •
• • •
• •
• •
• • • •
• • •
• •
Using the High Speed Counter
RAC - Reset Accumulated Value
Instruction Type: output
Table 9-15: Execution Time for the RAC Instruction
When Rung Is:
True
False
17.61 µs
0.00 µs
The RAC instruction resets the high speed counter and allows a specific value to be
written to the HSC accumulator. The RAC instruction uses the following parameters:
•
Counter Number - Specifies which high speed counter is being used; 0 = HSC0
and 1 = HSC1.
•
Source - Specifies the location of the data to be loaded into the HSC accumulator.
The data range is from -2,147,483,648 to 2,147,483,647.
Valid Addressing Modes and File Types are shown below:
Table 9-16: RAC Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Data Files
Parameter
Function Files
Counter Number
Source
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CSF - Comms
IOS - I/O
Immediate
Direct
Indirect
Element
Bit
Word
Long Word
HSL
HSL
High Speed Counter Load
HSC Number
HSC0
High Preset
N7:0
Low Preset
N7:1
Output High Source
N7:2
Output Low Source
N7:3
•
•
• • •
•
9-31
MicroLogix 1500 Programmable Controllers User Manual
9-32
Using High Speed Outputs
10
Using High Speed Outputs
The input and output instructions allow you to selectively update data without waiting
for the input and output scans.
Instruction
Used To:
Page
PTO - Pulse Train Output
Generate stepper pulses
10-1
PWM - Pulse Width Modulation
Generate PWM output
10-20
PTO - Pulse Train Output Instruction
Instruction Type: output
Table 10-1: Execution Time for the PTO Instruction
When Rung Is:
True
False
75.11 µs
21.4 µs
Pulse Train Output Function
A controller utilizing a 1764-28BXB Base Unit supports two high speed outputs.
These outputs can be used as standard outputs (not high speed), or individually
configured for PTO or PWM operation. The PTO functionality allows a simple
motion profile or pulse profile to be generated directly from the controller. The pulse
profile has three primary components:
•
Total number of pulses to be generated
•
Accelerate/decelerate intervals
•
Run interval
10-1
MicroLogix 1500 Programmable Controllers User Manual
The PTO instruction, along with the HSC and PWM functions, are different than most
other controller instructions. Their operation is performed by custom circuitry that
runs in parallel with the main system processor. This is necessary because of the high
performance requirements of these functions.
In this implementation, the user defines the total number of pulses to be generated
(which corresponds to distance traveled), and how many pulses to use for each accel/
decel period. The number of pulses not used in the accel/decel period defines how
many pulses will be generated during the run phase. In this implementation, the accel/
decel intervals are the same.
Within the PTO function file are two PTO elements. Each element can be set to
control either output 2 (O0:0/2) or output 3 (O0:0/3).
The interface to the PTO sub-system is accomplished by scanning a PTO instruction
in the main program file (file number 2), or by scanning a PTO instruction in any of
the subroutine files. A typical operating sequence of a PTO instruction is as follows:
1. The rung that a PTO instruction is on is solved true.
2. The PTO instruction is started, and pulses are produced based on the accel/decel
(ACCEL) parameters, which define the number of ACCEL pulses and the type of
profile: s-curve or trapezoid.
3. The ACCEL phase completes.
4. The RUN phase is entered, and the number of pulses defined for RUN are output.
5. The RUN phase completes.
6. Decelerate (DECEL) is entered, and pulses are produced based on the accel/decel
parameters, which defines the number of DECEL pulses and the type of profile: scurve or trapezoid.
7. The DECEL phase completes.
8. The PTO instruction is DONE.
While the PTO instruction is being executed/processed, status bits and information
are updated as the main controller continues to operate. Because the PTO instruction
is actually being executed by a parallel system, the status bits and other information
are updated each time the PTO instruction is scanned while it is running. This
provides the control program access to PTO status while it is running.
10-2
Using High Speed Outputs
Note:
PTO status is only as fresh as the scan time of the controller. Worst case
latency will be the same as the maximum scan of the controller. This
condition can be minimized by placing a PTO instruction in the STI
(selectable timed interrupt) file, or by adding PTO instructions to your
program to increase how often a PTO instruction is scanned.
The charts in the following examples illustrate the typical timing sequence/behavior
of a PTO instruction. The stages listed in each chart have nothing to do with controller
scan time. They simply illustrate a sequence of events. In actuality, the controller may
have hundreds or thousands of scans within each of the stages illustrated in the
examples.
Conditions Required to Start the PTO
The following conditions must exist to start the PTO:
•
•
•
The PTO instruction must be in an idle state.
For idle state behavior, all of the following conditions must be met:
v Jog Pulse (JP) bit must be off
v Jog Continuous (JC) bit must be off
v Enable Hardstop (EH) bit must be off
v Normal Operation (NS) bit must be off
v The output cannot be forced
The rung it is on must transition from a False state (0) to a True state (1).
10-3
MicroLogix 1500 Programmable Controllers User Manual
Momentary Logic Enable Example
In this example, the rung state is a momentary or transitional type of input. This
means that the false-to-true rung transition enables the PTO instruction, and then
returns to a false state prior to the PTO instruction completing its operation.
If a transitional input to the PTO instruction is used, the Done (DN) bit turns on when
the instruction completes, but will only remain on until the next time the PTO
instruction is scanned in the user program. The structure of the control program
determines when the DN bit goes off. So, to detect when the PTO instruction
completes its output, you can monitor the Done (DN), Idle (ID), or Normal Operation
(NO) status bits.
Table 10-2: Chart 1 - Momentary (rung) Logic Enable
Stage
Rung State
0
1
2
3
4
5
Sub-Elements:
Normal Operation
6
7
8
9
10
11
12
Relative Timing
/NO
Accelerate Status
/AS
Run Status
/RS
Decelerate Status
/DS
Enable
/EN
Done
/DN
Idle
/ID
Jog Pulse
/JP
Jog Continuous
/JC
Start of PTO
10-4
Start of PTO
Using High Speed Outputs
Standard Logic Enable Example
In this example, the rung state is a maintained type of input. This means that it enables
the PTO instruction Normal Operation (NO), and maintains its logic state until after
the PTO instruction completes its operation. With this type of logic, status bit
behavior is as follows:
The Done (DN) bit will becomes true (1) when the PTO completes, and remains set
until the PTO rung logic is false. The false rung logic re-activates the PTO instruction.
To detect when the PTO instruction completes its output, you monitor the done (DN)
bit.
Table 10-3: Chart 2 - Standard (rung) Logic Enable
Stage
Rung State
0
1
2
3
4
5
Sub-Elements:
Normal Operation
6
7
8
9
10
11
12
Relative Timing
/NO
Accelerate Status
/AS
Run Status
/RS
Decelerate Status
/DS
Enable
/EN
Done
/DN
Idle
/ID
Jog Pulse
/JP
Jog Continuous
/JC
Start of PTO
Start of PTO
10-5
MicroLogix 1500 Programmable Controllers User Manual
Pulse Train Outputs (PTO) Function File
Within the RSLogix 500 Function File Folder, you see a PTO Function File with two
elements, PTO0 and PTO1. These elements provide access to PTO configuration data,
and also allow the control program access to all information pertaining to each of the
Pulse Train Outputs.
Note:
10-6
If the controller mode is run, the data within sub-element fields may be
changing.
Using High Speed Outputs
Pulse Train Output Function File Sub-Elements Summary
The variables within each PTO sub-element, along with what type of behavior and
access the control program has to those variables, are listed individually below. All
examples illustrate PTO 0. Terms and behavior for PTO 1 are identical.
Table 10-4: Pulse Train Output Function File (PTO:0)
Sub-Element Description
OUT - Output
DN - Done
DS - Decelerating Status
RS - Run Status
AS - Accelerating Status
RP - Ramp Profile
IS - Idle Status
ED - Error Detected Status
NS - Normal Operation Status
JPS - Jog Pulse Status
JCS - Jog Continuous Status
JP - Jog Pulse
JC - Jog Continuous
EH - Enable Hard Stop
EN - Enable Status (follows rung
state)
ER - Error Code
OF - Output Frequency (Hz)
OFS - Operating Frequency Status
(Hz)
JF - Jog Frequency (Hz)
TOP - Total Output Pulses To Be
Generated
OPP - Output Pulses Produced
ADP - Accel/Decel Pulses
Address
Data
Format
PTO:0.OUT word (INT)
PTO:0/DN bit
PTO:0/DS bit
PTO:0/RS bit
PTO:0/AS
bit
PTO:0/RP bit
PTO:0/IS
bit
PTO:0/ED bit
PTO:0/NS bit
PTO:0/JPS bit
PTO:0/JCS bit
PTO:0/JP
bit
PTO:0/JC
bit
PTO:0/EH bit
PTO:0/EN bit
Range
Type
control
status
status
status
status
control
status
status
status
status
status
control
control
control
status
User Program
Access
read only
read only
read only
read only
read only
read/write
read only
read only
read only
read only
read only
read/write
read/write
read/write
read only
For More
Information
10-8
10-8
10-9
10-9
10-10
10-10
10-11
10-11
10-17
10-17
10-18
10-16
10-12
10-12
10-13
2 or 3
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
PTO:0.ER word (INT)
PTO:0.OF word (INT)
PTO:0.OFS word (INT)
-2 to 7
0 to 20,000
0 to 20,000
status
control
status
read only
read/write
read only
10-18
10-13
10-14
PTO:0.JF
word (INT)
PTO:0.TOP long word
(32-bit INT)
PTO:0.OPP long word
(32-bit INT)
PTO:0.ADP long word
(32-bit INT)
0 to 20,000
0 to 2,147,483,647
control
control
read/write
read/write
10-16
10-14
0 to 2,147,483,647
status
read only
10-14
see p. 10-15
control
read/write
10-15
10-7
MicroLogix 1500 Programmable Controllers User Manual
PTO Output (OUT)
Sub-Element Description
OUT - Output
Address
Data Format
PTO:0.OUT word (INT)
Range
2 or 3
Type
control
User Program Access
read only
The PTO OUT (Output) variable defines the output (O0:0/2 or O0:0/3) that the PTO
instruction controls. This variable is set within the function file folder when the
control program is written, and cannot be set by the user program.
•
When OUT = 2, PTO pulses output 2 (O0:0.0/2) of the embedded outputs
(1764-28BXB).
•
When OUT = 3, PTO pulses output 3 (O0:0.0/3) of the embedded outputs
(1764-28BXB).
Note:
Forcing an output controlled by the PTO while it is running will cause a PTO
error.
PTO Done (DN)
Sub-Element Description
DN - Done
Address
PTO:0/DN
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO DN (Done) bit is controlled by the PTO sub-system. It can be used by an
input instruction on any rung within the control program. The DN bit operates as
follows:
10-8
•
Set (1) - Whenever a PTO instruction has completed its operation successfully.
•
Cleared (0) - When the rung the PTO is on is false. If the rung is false when the
PTO instruction completes, the Done bit is set until the next scan of the PTO
instruction.
Using High Speed Outputs
PTO Decelerating Status (DS)
Sub-Element Description
DS - Decelerating Status
Address
PTO:0/DS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO DS (Decel) bit is controlled by the PTO sub-system. It can be used by an
input instruction on any rung within the control program. The DS bit operates as
follows:
•
Set (1) - Whenever a PTO instruction is within the deceleration phase of the
output profile.
•
Cleared (0) - Whenever a PTO instruction is not within the deceleration phase of
the output profile.
PTO Run Status (RS)
Sub-Element Description
RS - Run Status
Address
PTO:0/RS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO RS (Run Status) bit is controlled by the PTO sub-system. It can be used by
an input instruction on any rung within the control program. The RS bit operates as
follows:
•
Set (1) - Whenever a PTO instruction is within the run phase of the output profile.
•
Cleared (0) - Whenever a PTO instruction is not within the run phase of the output
profile.
10-9
MicroLogix 1500 Programmable Controllers User Manual
PTO Accelerating Status (AS)
Sub-Element Description
AS - Accelerating Status
Address
PTO:0/AS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO AS (Accelerating Status) bit is controlled by the PTO sub-system. It can be
used by an input instruction on any rung within the control program. The AS bit
operates as follows:
•
Set (1) - Whenever a PTO instruction is within the acceleration phase of the output
profile.
•
Cleared (0) - Whenever a PTO instruction is not within the acceleration phase of
the output profile.
PTO Ramp Profile (RP)
Sub-Element Description
RP - Ramp Profile
Address
PTO:0/RP
Data Format
bit
Range
0 or 1
Type
control
User Program Access
read/write
The PTO RP (Ramp Profile) bit controls how the output pulses generated by the PTO
sub-system accelerate to and decelerate from the Output Frequency that is set in the
PTO function file (PTO:0.OF). It can be used by an input or output instruction on any
rung within the control program. The RP bit operates as follows:
10-10
•
Set (1) - Configures the PTO instruction to produce an S-Curve profile.
•
Cleared (0) - Configures the PTO instruction to produce a Trapezoid profile.
Using High Speed Outputs
PTO Idle Status (IS)
Sub-Element Description
IS - Idle Status
Address
PTO:0/IS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO IS (Idle Status) is controlled by the PTO sub-system. It can be used in the
control program by an input instruction. The PTO sub-system must be in an idle state
whenever any PTO operation needs to start.
The IS bit operates as follows:
•
Set (1) - PTO sub-system is in an idle state. The idle state is defined as the PTO is
not running, and no errors are present.
•
Cleared (0) - PTO sub-system is not in an idle state (it is running)
PTO Error Detected (ED)
Sub-Element Description
ED - Error Detected Status
Address
PTO:0/ED
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO ED (Error Detected Status) bit is controlled by the PTO sub-system. It can
be used by an input instruction on any rung within the control program to detect when
the PTO instruction is in an error state. If an error state is detected, the specific error is
identified in the error code register (PTO:0.ER). The ED bit operates as follows:
•
Set (1) - Whenever a PTO instruction is in an error state
•
Cleared (0) - Whenever a PTO instruction is not in an error state
10-11
MicroLogix 1500 Programmable Controllers User Manual
PTO Normal Operation Status (NS)
Sub-Element Description
NS - Normal Operation Status
Address
PTO:0/NS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO NS (Normal Operation Status) bit is controlled by the PTO sub-system. It
can be used by an input instruction on any rung within the control program to detect
when the PTO is in its normal state. A normal state is ACCEL, RUN, DECEL or
DONE, with no PTO errors. The NS bit operates as follows:
•
Set (1) - Whenever a PTO instruction is in its normal state
•
Cleared (0) - Whenever a PTO instruction is not in its normal state
PTO Enable Hard Stop (EH)
Sub-Element Description
EH - Enable Hard Stop
Address
PTO:0/EH
Data Format
bit
Range
0 or 1
Type
control
User Program Access
read/write
The PTO EH (Enable Hard Stop) bit is used to stop the PTO sub-system immediately.
Once the PTO sub-system starts a pulse sequence, the only way to stop generating
pulses is to set the enable hard stop bit. The enable hard stop aborts any PTO subsystem operation (idle, normal, jog continuous or jog pulse) and generates a PTO subsystem error. The EH bit operates as follows:
10-12
•
Set (1) - Instructs the PTO sub-system to stop generating pulses immediately
(output off = 0)
•
Cleared (0) - Normal operation
Using High Speed Outputs
PTO Enable Status (EN)
Sub-Element Description
Address
EN - Enable Status (follows rung PTO:0/EN
state)
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO EN (Enable Status) is controlled by the PTO sub-system. When the rung
preceding the PTO instruction is solved true, the PTO instruction is enabled and the
enable status bit is set. If the rung preceding the PTO instruction transitions to a false
state before the pulse sequence completes its operation, the enable status bit resets (0).
The EN bit operates as follows:
•
Set (1) - PTO is enabled
•
Cleared (0) - PTO has completed, or the rung preceding the PTO is false
PTO Output Frequency (OF)
Sub-Element Description
OF - Output Frequency (Hz)
Address
PTO:0.OF
Data Format
word (INT)
Range
0 to 20,000
Type
control
User Program Access
read/write
The PTO OF (Output Frequency) variable defines the frequency of the PTO output
during the RUN phase of the pulse profile. This value is typically determined by the
type of device that is being driven, the mechanics of the application, or the device/
components being moved. Data less than zero and greater than 20,000 generates a
PTO error.
10-13
MicroLogix 1500 Programmable Controllers User Manual
PTO Operating Frequency Status (OFS)
Sub-Element Description
OFS - Operating Frequency
Status (Hz)
Address
Data Format
PTO:0.OFS word (INT)
Range
0 to 20,000
Type
status
User Program Access
read only
The PTO OFS (Output Frequency Status) is generated by the PTO sub-system and
can be used in the control program to monitor the actual frequency being produced by
the PTO sub-system.
Note:
The value displayed may not exactly match the value entered in the
PTO:0.OF. This is because the PTO sub-system may not be capable of
reproducing an exact frequency at some of the higher frequencies. For PTO
applications, this is typically not an issue because, in all cases, an exact
number of pulses are produced.
PTO Total Output Pulses To Be Generated (TOP)
Sub-Element Description
Address
Data Format
Range
TOP - Total Output Pulses To Be PTO:0.TOP long word (32-bit INT) 0 to 2,147,483,647
Generated
Type
control
User Program Access
read/write
The PTO TOP (Total Output Pulses) defines the total number of pulses to be
generated for the pulse profile (accel/run/decel inclusive).
PTO Output Pulses Produced (OPP)
Sub-Element Description
OPP - Output Pulses Produced
Address
Data Format
Range
PTO:0.OPP long word (32-bit INT) 0 to 2,147,483,647
Type
status
User Program Access
read only
The PTO OPP (Output Pulses Produced) is generated by the PTO sub-system and can
be used in the control program to monitor how many pulses have been generated by
the PTO sub-system.
10-14
Using High Speed Outputs
PTO Accel / Decel Pulses (ADP)
Sub-Element Description
ADP - Accel/Decel Pulses
Address
Data Format
PTO:0.ADP long word (32-bit INT)
Range
see below
Type
control
User Program Access
read/write
The PTO ADP (Accel/Decel Pulses) defines how many of the total pulses (TOP
variable) will be applied to each of the ACCEL and DECEL components. The
illustration below shows the relationship, where:
•
TOP (total output pulses) = 12,000
•
ADP (accel/decel pulses)= 3,000
If you need to determine the ramp period (accel/decel ramp duration):
•
2 x ADP/OF = duration in seconds (OF = output frequency)
The following formulas can be used to calculate the maximum frequency limit for
both profiles. The maximum frequency = the integer ≤ the result found below
(OF = output frequency):
•
For Trapezoid Profiles: OF x OF/4 + 0.5
•
For S-Curve Profiles: 0.999 x OF x SQRT(OF/6)
12,000
Accel
Run
Decel
3,000
6,000
3,000
The ADP range is from 0 to the calculated value. The value in the ADP variable must
be less than one-half the value in the TOP variable, or an error is generated. In this
example, the maximum value that could be used for accel/decel is 6000, because if
both accel and decel are 6000, the total number of pulses = 12,000. The run
component would be zero. This profile would consist of an acceleration phase from 0
to 6000. At 6000, the output frequency (OF variable) would be generated and
immediately enter the deceleration phase, 6000 to 12,000. At 12,000, the PTO
operation would stop (output frequency = 0).
10-15
MicroLogix 1500 Programmable Controllers User Manual
PTO Jog Frequency (JF)
Sub-Element Description
JF - Jog Frequency (Hz)
Address
PTO:0.JF
Data Format
word (INT)
Range
0 to 20,000
Type
control
User Program Access
read/write
The PTO JF (Jog Frequency) variable defines the frequency of the PTO output during
all Jog phases. This value is typically determined by the type of device that is being
driven, the mechanics of the application, or the device/components being moved).
Data less than zero and greater than 20,000 generates a PTO error.
PTO Jog Pulse (JP)
Sub-Element Description
JP - Jog Pulse
Address
PTO:0/JP
Data Format
bit
Range
0 or 1
Type
control
User Program Access
read/write
The PTO JP (Jog Pulse) bit is used to instruct the PTO sub-system to generate a single
pulse. The width is defined by the Jog Frequency parameter in the PTO function file.
Jog Pulse operation is only possible under the following conditions:
•
PTO sub-system in idle
•
Jog continuous not active
•
Enable not active
The JP bit operates as follows:
10-16
•
Set (1) - Instructs the PTO sub-system to generate a single Jog Pulse
•
Cleared (0) - Arms the PTO Jog Pulse sub-system
Using High Speed Outputs
PTO Jog Pulse Status (JPS)
Sub-Element Description
JPS - Jog Pulse Status
Address
PTO:0/JPS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO JPS (Jog Pulse Status) bit is controlled by the PTO sub-system. It can be
used by an input instruction on any rung within the control program to detect when
the PTO has generated a Jog Pulse.
The JPS bit operates as follows:
•
Set (1) - Whenever a PTO instruction outputs a Jog Pulse
•
Cleared (0) - Whenever a PTO instruction exits the Jog Pulse state
Note:
The output (jog) pulse is normally complete with the JP bit set. The JPS bit
remains set until the JP bit is cleared (0 = off).
PTO Jog Continuous (JC)
Sub-Element Description
JC - Jog Continuous
Address
PTO:0/JC
Data Format
bit
Range
0 or 1
Type
control
User Program Access
read/write
The PTO JC (Jog Continuous) bit instructs the PTO sub-system to generate
continuous pulses. The frequency generated is defined by the Jog Frequency
parameter in the PTO function file. Jog Continuous operation is only possible under
the following conditions:
•
PTO sub-system in idle
•
Jog Pulse not active
•
Enable not active
The JC bit operates as follows:
•
Set (1) - Instructs the PTO sub-system to generate continuous Jog Pulses
•
Cleared (0) - The PTO sub-system does not generate Jog Pulses
When the Jog Continuous bit is cleared, the current output pulse is truncated.
10-17
MicroLogix 1500 Programmable Controllers User Manual
PTO Jog Continuous Status (JCS)
Sub-Element Description
JCS - Jog Continuous Status
Address
PTO:0/JCS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PTO JCS (Jog Continuous Status) bit is controlled by the PTO sub-system. It can
be used by an input instruction on any rung within the control program to detect when
the PTO is generating continuous Jog Pulses. The JCS bit operates as follows:
Set (1) - Whenever a PTO instruction is generating continuous Jog Pulses
Cleared (0) - Whenever a PTO instruction is not generating continuous Jog Pulses.
PTO Error Code (ER)
Sub-Element Description
ER - Error Code
Address
PTO:0.ER
Data Format
word (INT)
Range
-2 to 7
Type
status
User Program Access
read only
PTO ER (Error Codes) detected by the PTO sub-system are displayed in this register.
The error codes are shown in the table below:
Table 10-5: Pulse Train Output Error Codes
Error
Code
-2
Non-User
Fault
Yes
-1
Yes
0
1
--No
2
No
10-18
Recoverable Instruction Error Name Description
Fault
Errors
No
No
Overlap Error An output overlap is detected. Multiple functions are assigned
to the same physical output. This is a configuration error. The
controller faults and the User Fault Routine does not execute.
Example: PTO0 and PTO1 are both attempting to use a single
output.
No
No
Output Error An invalid output has been specified. Output 2 and output 3
are the only valid choices. This is a configuration error. The
controller faults and the User Fault Routine does not execute.
--Normal
Normal (0 = no error present)
No
Yes
Hardstop This error is generated whenever a hardstop is detected. This
Detected error does not fault the controller. It is automatically cleared
when the hardstop condition is removed.
No
Yes
Output Forced The configured PTO output (2 or 3) is currently forced. The
Error
forced condition must be removed for the PTO to operate.
This error does not fault the controller. It is automatically
cleared when the force condition is removed.
Using High Speed Outputs
Table 10-5: Pulse Train Output Error Codes
Error
Code
3
Non-User
Fault
No
Recoverable Instruction
Fault
Errors
Yes
No
4
No
Yes
No
5
No
No
Yes
6
No
Yes
No
7
Yes
Yes
No
Error Name Description
Frequency
Error
The operating frequency value (OFS) is less than 0 or greater
than 20,000. This error faults the controller. It can be cleared
by logic within the User Fault Routine.
Accel/Decel The accel/decel parameters (ADP) are:
Error
• less than zero
• greater than half the total output pulses to be generated
(TOP)
• Accel/Decel exceeds limit (See page 10-15.)
This error faults the controller. It can be cleared by logic within
the User Fault Routine.
Jog Error PTO is in the idle state and two or more of the following are
set:
• Enable (EN) bit set
• Jog Pulse (JP) bit set
• Jog Continuous (JC) bit set
This error does not fault the controller. It is automatically
cleared when the error condition is removed.
Jog
The jog frequency (JF) value is less than 0 or greater than
Frequency 20,000. This error faults the controller. It can be cleared by
Error
logic within the User Fault Routine.
Length Error The total output pulses to be generated (TOP) is less than
zero. This error faults the controller. It can be cleared by logic
within the User Fault Routine.
10-19
MicroLogix 1500 Programmable Controllers User Manual
PWM - Pulse Width Modulation Instruction
Instruction Type: output
Table 10-6: Execution Time for the PWM Instruction
When Rung Is:
True
False
110.50 µs
21.63 µs
PWM Function
The PWM function allows a field device to be controlled by a PWM wave form. The
PWM profile has two primary components:
•
Frequency to be generated
•
Duty Cycle interval
The PWM instruction, along with the HSC and PTO functions, are different than all
other controller instructions. Their operation is performed by custom circuitry that
runs in parallel with the main system processor. This is necessary because of the high
performance requirements of these instructions.
The interface to the PWM sub-system is accomplished by scanning a PWM
instruction in the main program file (file #2), or by scanning a PWM instruction in
any of the subroutine files. A typical operating sequence of a PWM instruction is as
follows:
1. The rung that a PWM instruction is on is solved true (the PWM is started).
2. A waveform at the specified frequency is produced.
3. The RUN phase is active. A waveform at the specified frequency with the specified duty cycle is output.
4. The rung that the PWM is on is solved false.
5. The PWM instruction is IDLE.
10-20
Using High Speed Outputs
While the PWM instruction is being executed, status bits and data are updated as the
main controller continues to operate. Because the PWM instruction is actually being
executed by a parallel system, the status bits and other information are updated each
time the PWM instruction is scanned while it is running. This provides the control
program access to PWM status while it is running.
Note:
PWM status is only as fresh as the scan time of the controller. Worst case
latency is the maximum scan of the controller. This condition can be
minimized a by placing a PWM instruction in the STI (selectable timed
interrupt) file, or by adding PWM instructions to your program to
increase how often a PWM instruction is scanned.
Pulse Width Modulated (PWM) Function File
Within the PWM function file are two PWM elements. Each element can be set to
control either output 2 (O0:0/2) or output 3 (O0:0/3).
10-21
MicroLogix 1500 Programmable Controllers User Manual
Pulse Width Modulated Function File Elements Summary
The variables within each PWM element, along with what type of behavior and
access the control program has to those variables, are listed individually below.
Table 10-7: Pulse Width Modulated Function File (PWM:0)
Element Description
OUT - PWM Output
RS - PWM Run Status
IS - PWM Idle Status
ED - PWM Error Detection
NS - PWM Normal Operation
EH - PWM Enable Hard Stop
ES - PWM Enable Status
OF - PWM Output Frequency
OFS - PWM Operating Frequency Status
DC - PWM Duty Cycle
DCS - PWM Duty Cycle Status
ER - PWM Error Codes
Address
Data
Format
PWM:0.OUT
PWM:0/RS
PWM:0/IS
PWM:0/ED
PWM:0/NS
PWM:0/EH
PWM:0/ES
PWM:0.OF
PWM:0.OFS
PWM:0.DC
PWM:0.DCS
PWM:0.ER
word (INT)
bit
bit
bit
bit
bit
bit
word (INT)
word (INT)
word (INT)
word (INT)
word (INT)
Range
Type
2 or 3
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 to 20,000
0 to 20,000
1 to 1000
1 to 1000
-2 to 5
status
status
status
status
status
control
status
control
status
control
status
status
User
Program
Access
read only
read only
read only
read only
read only
read/write
read only
read/write
read only
read/write
read only
read only
For More
Information
10-22
10-23
10-23
10-23
10-24
10-24
10-24
10-25
10-25
10-25
10-26
10-26
PWM Output (OUT)
Element Description
OUT - PWM Output
Address
PWM:0.OUT
Data Format
word (INT)
Range
2 or 3
Type
status
User Program Access
read only
The PWM OUT (Output) variable defines the physical output (O0:0/2 or O0:0/3) that
the PWM instruction controls. This variable is set within the function file folder when
the control program is written, and cannot be set by the user program
10-22
•
PWM modulates output 2 (O0:0.0/2) of the embedded outputs (1764-28BXB)
•
PWM modulates output 3 (O0:0.0/3) of the embedded outputs (1764-28BXB)
Using High Speed Outputs
PWM Run Status (RS)
Element Description
RS - PWM Run Status
Address
PWM:0/RS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PWM RS (Run Status) bit is controlled by the PWM sub-system. It can be used
by an input instruction on any rung within the control program.
•
Set (1) - Whenever the PWM instruction is within the run phase of the output
profile.
•
Cleared (0) - Whenever the PWM instruction is not within the run phase of the
output profile.
PWM Idle Status (IS)
Element Description
IS - PWM Idle Status
Address
PWM:0/IS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PWM IS (Idle Status) is controlled by the PWM sub-system and represents no
PWM activity. It can be used in the control program by an input instruction.
•
Set (1) - PWM sub-system is in an idle state.
•
Cleared (0) - PWM sub-system is not in an idle state (it is running).
PWM Error Detected (ED)
Element Description
ED - PWM Error Detection
Address
PWM:0/ED
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PWM ED (Error Detected) bit is controlled by the PWM sub-system. It can be
used by an input instruction on any rung within the control program to detect when
the PWM instruction is in an error state. If an error state is detected, the specific error
is identified in the error code register (PWM:0.ED).
•
Set (1) - Whenever a PWM instruction is in an error state.
•
Cleared (0) - Whenever a PWM instruction is not in an error state.
10-23
MicroLogix 1500 Programmable Controllers User Manual
PWM Normal Operation (NS)
Element Description
NS - PWM Normal Operation
Address
PWM:0/NS
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PWM NS (Normal Operation) bit is controlled by the PWM sub-system. It can be
used by an input instruction on any rung within the control program to detect when
the PWM is in its normal state. A normal state is defined as ACCEL, RUN, or
DECEL with no PWM errors.
•
Set (1) - Whenever a PWM instruction is in its normal state.
•
Cleared (0) - Whenever a PWM instruction is not in its normal state.
PWM Enable Hardstop (EH)
Element Description
EH - PWM Enable Hard Stop
Address
PWM:0/EH
Data Format
bit
Range
0 or 1
Type
control
User Program Access
read/write
The PWM EH (Enable Hard Stop) bit stops the PWM sub-system immediately. A
PWM hard stop generates a PWM sub-system error.
•
Set (1) - Instructs the PWM sub-system to stop its output modulation immediately
(output off = 0).
•
Cleared (0) - Normal operation.
PWM Enable Status (ES)
Element Description
ES - PWM Enable Status
Address
PWM:0/ES
Data Format
bit
Range
0 or 1
Type
status
User Program Access
read only
The PWM ES (Enable Status) is controlled by the PWM sub-system. When the rung
preceding the PWM instruction is solved true, the PWM instruction is enabled, and
the enable status bit is set. When the rung preceding the PWM instruction transitions
to a false state, the enable status bit is reset (0) immediately.
10-24
•
Set (1) - PWM is enabled.
•
Cleared (0) - PWM has completed or the rung preceding the PWM is false.
Using High Speed Outputs
PWM Output Frequency (OF)
Element Description
OF - PWM Output Frequency
Address
PWM:0.OF
Data Format
word (INT)
Range
0 to 20,000
Type
control
User Program Access
read/write
The PWM OF (Output Frequency) variable defines the frequency of the PWM
function. This frequency can be changed at any time.
PWM Operating Frequency Status (OFS)
Element Description
Address
OFS - PWM Operating Frequency Status PWM:0.OFS
Data Format
word (INT)
Range
0 to 20,000
Type
status
User Program Access
read only
The PWM OFS (Output Frequency Status) is generated by the PWM sub-system and
can be used in the control program to monitor the actual frequency produced by the
PWM sub-system.
PWM Duty Cycle (DC)
Element Description
DC - PWM Duty Cycle
Address
PWM:0.DC
Data Format
word (INT)
Range
1 to 1000
Type
control
User Program Access
read/write
The PWM DC (Duty Cycle) variable controls the output signal produced by the PWM
sub-system. Changing this variable in the control program changes the output
waveform. Typical values and output waveform:
•
DC = 1000: 100% Output ON (constant, no waveform)
•
DC = 750: 75% Output ON, 25% output OFF
•
DC = 500: 50% Output ON, 50% output OFF
•
DC = 250: 25% Output ON, 75% output OFF
•
DC = 0: 0% Output OFF (constant, no waveform)
10-25
MicroLogix 1500 Programmable Controllers User Manual
PWM Duty Cycle Status (DCS)
Element Description
DCS - PWM Duty Cycle Status
Address
PWM:0.DCS
Data Format
word (INT)
Range
1 to 1000
Type
status
User Program Access
read only
The PWM DCS (Duty Cycle Status) provides feedback from the PWM sub-system.
The Duty Cycle Status variable can be used within an input instruction on a rung of
logic to provide PWM system status to the remaining control program.
PWM Error Code (ER)
Element Description
ER - PWM Error Codes
Address
PWM:0.ER
Data Format
word (INT)
Range
-2 to 5
Type
status
User Program Access
read only
PWM ER (Error Codes) detected by the PWM sub-system are displayed in this
register. The table identifies known errors.
Table 10-8: PWM Error Codes
Error
Code
Non-User
Fault
Recoverable
Fault
-2
Yes
No
No
-1
Yes
No
No
0
1
No
No
Yes
2
No
No
Yes
3
Yes
Yes
No
4
5
Yes
Yes
No
10-26
Instruction
Error Name
Errors
Description
Overlap An output overlap is detected. Multiple functions are assigned to the
Error
same physical output. This is a configuration error. The controller faults
and the User Fault Routine does not execute. Example: PWM0 and
PWM1 are both attempting to use a single output.
Output An invalid output has been specified. Output 2 and output 3 are the
Error
only valid choices. This is a configuration error. The controller faults
and the User Fault Routine does not execute.
Normal Normal (0 = no error present)
Hardstop This error is generated whenever a hardstop is detected. This error
Error
does not fault the controller. It is automatically cleared when the
hardstop condition is removed.
Output The configured PWM output (2 or 3) is currently forced. The forced
Forced condition must be removed for the PWM to operate.
Error
This error does not fault the controller. It is automatically cleared when
the force condition is removed.
Frequency The frequency value is less than 0 or greater than 20,000. This error
Error
faults the controller. It can be cleared by logic within the User Fault
Routine.
Reserved
Duty Cycle The PWM duty cycle is either less than zero or greater than 1000.
Error
This error faults the controller. It can be cleared by logic within the User
Fault Routine.
Programming Instructions Overview
11
Programming Instructions Overview
Instruction Set
The following table shows the MicroLogix 1500 programming instructions listed
within their functional group.
Functional Group
Description
Relay-Type (Bit)
The relay-type (bit) instructions monitor and control the status of bits.
XIC, XIO, OTE, OTL, OTU, OSR, ONS, OSF
Timer and Counter The timer and counter instructions control operations based on time or the number of events.
TON, TOF, RTO, CTU, CTD, RES
Compare
The compare instructions compare values by using a specific compare operation.
EQU, NEQ, LES, LEQ, GRT, GEQ, MEQ, LIM
Math
The math instructions perform arithmetic operations.
ADD, SUB, MUL, DIV, NEG, CLR, SQR, SCL, SCP
Conversion
The conversion instructions multiplex and de-multiplex data and perform conversions between
binary and decimal values. DCD, ENC, TOD, FRD
Logical
The logical instructions perform bit-wise logical operations on words.
AND, OR, XOR, NOT
Move
The move instructions modify and move words.
MOV, MVM
File
The file instructions perform operations on file data.
COP, FLL, BSL, BSR, FFL, FFU, LFL, LFU
Sequencer
Sequencer instructions are used to control automatic assembly machines that have consistent and
repeatable operations. SQC, SQO, SQL
Program Control
The program flow instructions change the flow of ladder program execution.
JMP, LBL, JSR, SBR, RET, SUS, TND, MCR, END
Input and Output
The input and output instructions allow you to selectively update data without waiting for the input
and output scans.
IIM, IOM, REF
User Interrupt
The user interrupt instructions allow you to interrupt your program based on defined events.
STS, INT, UID, UIE, UIF
Process Control
The process control instruction provides closed-loop control.
PID
Communications
The communication instructions read or write data to another station.
MSG, SVC
Page
12-1
13-1
14-1
15-1
16-1
17-1
18-1
19-1
20-1
21-1
22-1
23-1
24-1
25-1
11-1
MicroLogix 1500 Programmable Controllers User Manual
Using the Instruction Descriptions
Throughout this manual, each instruction (or group of similar instructions) has a table
similar to the one shown below. This table provides information for all sub-elements
(or components) of an instruction or group of instructions. This table identifies the
type of compatible address that can be used for each sub-element of an instruction or
group of instructions in a data file or function file. The definitions of the terms used in
these tables are listed below this example table.
Table 11-1: Valid Addressing Modes and File Types - Example Table
Parameter
Source A
Source B
Destination
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DATI
TPI
CSF - Comms
ISF - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • •
• •
•
• •
• •
• •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DATI, TPI, CSF, and ISF files.
The terms used within the table are defined as follows:
11-2
•
Parameter - The parameter is the information you supply to the instruction. It can
be an address, a value, or an instruction-specific parameter such as a timebase.
•
Data Files - See “Data Files” on page 6-5.
•
Function Files - See “Function Files” on page 6-12.
•
CSF - See “Communications Status File” on page 6-13.
•
ISF - See “Input/Output Status File” on page 6-17.
•
Addressing Level - Address levels describe the granularity at which an instruction
will allow an operand to be used. For example, relay type instructions (XIC, XIO,
etc.) must be programmed to the bit level, timer instructions (TON, TOF, etc.)
must be programmed to the element level (timers have 3 words per element) and
math instructions (ADD, SUB, etc.) must be programmed to the word or long
word level.
Programming Instructions Overview
Addressing Modes
The MicroLogix 1500 supports three types of data addressing:
•
Immediate
•
Direct
•
Indirect
The MicroLogix 1500 does not support indexed addressing.
How or when each type is used depends on the instruction being programmed, and the
type of elements specified within the operands of the instructions. By supporting
these three addressing methods, the MicroLogix 1500 allows incredible flexibility in
how data can be monitored or manipulated. Each of the addressing modes are
described below.
Immediate Addressing
Immediate addressing is primarily used to assign numeric constants within
instructions. For example: You require a 10 second timer, so you program a timer with
a 1 second time base, and a preset value of 10. The numbers 1 and 10 in this example
are both forms of immediate addressing.
Direct Addressing
When you use direct addressing, you define a specific data location within the
controller. Any data location that is supported by the elements of an operand within
the instruction being programmed can be used. In this example we are illustrating a
limit instruction, where.
•
Low Limit = This is an immediate value entered from the programming software.
•
Test Value = TPI:TP0 (This is the current position/value of trim pot 0.)
•
High Limit = N7:17 (This is the data resident in Integer file 7, element 17.)
TPI:TP0 and N7:17 are direct addressing examples
11-3
MicroLogix 1500 Programmable Controllers User Manual
Indirect Addressing
Indirect addressing allows components within the address to be used as pointers to
other data locations within the controller. This functionality can be especially useful
for certain types of applications, recipe management, batch processing and many
others. Indirect addressing can also be difficult to understand and troubleshoot. It is
recommended that you only use indirect addressing when it is required by the
application being developed.
The MicroLogix 1500 supports indirection (indirect addressing) for Files, Words and
Bits. To define which components of an address are to be indirected, a closed bracket
“[ ]” is used. The following examples illustrate how to use indirect addressing.
Indirect Addressing of a Word
B3:0
0000
0
•
Address: N7:[N10:1]
•
In this example, the element number to be used for source A in the ADD
instruction is defined by the number located in N10:1. If the value of location
N10:1 = 15, the ADD instruction will operate as “N7:15 + Source B”. When the
ADD instruction is scanned, N10:1 specifies the element to be used in the ADD
instruction.
•
In this example, integer file 7 is the source A file. The element specified by N10:1
must be between 0 and 255, because all MicroLogix 1500 data files have a
maximum size of 256 elements.
Note:
11-4
ADD
Add
Source A N7:[N10:1]
0<
Source B
1234
1234<
Dest
N11:33
0<
If a number larger than the number of elements in the data file is placed in
N10:1 (in this example), data integrity cannot be guaranteed, because a file
boundary will be crossed.
Programming Instructions Overview
Indirect Addressing of File
0001
LIM
Limit Test
Low Lim
Test
High Lim
B3:0
10
10<
N50:100
10<
25
25<
0
COP
Copy File
Source #N[N50:100]:10
Dest
#N7:0
Length
15
•
Address: N[N50:100]:10
•
Description: In this example, the element to be used for the indirection is
N50:100. The data in N50:100 will define the data file number to be used in the
instruction. In this example, the copy instruction source A is defined by
N[N50:100]:10. When the instruction is scanned, the data in N50:100 is used to
define the data file to be used for the COP instruction. If the value of location
N50:100 = 27, this instruction will copy 15 elements of data from N27:10
(N27:10 – N27:24) to N7:0 (N7:0 – N7:14)
Note:
If a number larger than 255 is placed in N50:100 in this example, a controller
fault will occur. This is because the controller has a maximum of 255 data
files. In addition, the file defined by the indirection should match the file
type defined by the instruction, in this example an integer file.
Note:
This example also illustrates how to perform a limit check on the indirect
address. The limit instruction at the beginning of the rung is monitoring the
indirect element. If the data at N50:100 is less than 10 or greater than 25, the
copy instruction will not be processed. This procedure can be used to make
sure an indirect address does not access data an unintended location.
11-5
MicroLogix 1500 Programmable Controllers User Manual
Indirect Addressing of Bit
B3:0
B3:0
[B25:0]
10
0002
•
Address: B3/[B25:0]
•
Description: In this example, the element to be used for the indirection is B25:0.
The data in B25:0 defines the bit within file B3. If the value of location B25:0 =
1017, the XIC instruction will be processed using B3/1017.
Note:
If a number larger than 4096 (or the number of elements in the data file) is
placed in B25:0 in this example, data integrity cannot be guaranteed.
Exceeding the number of elements in the data file would cause the file
boundary to be crossed.
These are only some of the examples that can be used, others include:
•
File and Element Indirection: N[N10]:[N25:0]
•
Input Slot Indirection: I[N7:0]:0
Each group of instructions may or may not allow indirection. Please review the
compatibility table for each instruction to determine which elements within an
instruction support indirection.
Important:
11-6
You must exercise extreme care when using indirect addressing.
Always be aware of the possibility of crossing file boundaries or
pointing to data that was not intended to be used.
Relay-Type (Bit) Instructions
12
Relay-Type (Bit) Instructions
Use relay-type (bit) instructions to monitor and/or control bits in a data file or
function file, such as input bits or timer control-word bits. The following instructions
are described in this chapter:
Instruction
XIC - Examine if Closed
XIO - Examine if Open
OTE - Output Enable
OTL - Output Latch
OTU - Output Unlatch
ONS - One Shot
OSR - One Shot Rising
OSF - One Shot Falling
Used To:
Examine a bit for an ON condition
Examine a bit for an OFF condition
Turn ON or OFF a bit (non-retentive)
Latch a bit ON (retentive)
Unlatch a bit OFF (retentive)
Detect an OFF to ON transition
Detect an OFF to ON transition
Detect an ON to OFF transition
Page
12-2
12-2
12-4
12-5
12-5
12-7
12-8
12-8
These instructions operate on a single bit of data. During operation, the processor may
set or reset the bit, based on logical continuity of ladder rungs. You can address a bit
as many times as your program requires.
12-1
MicroLogix 1500 Programmable Controllers User Manual
XIC - Examine if Closed
XIO - Examine if Open
Instruction Type: input
Table 12-1: Execution Time for the XIC and XIO Instructions
XIC
Instruction
Data Size
XIC and XIO
word
When Instruction Is:
True
False
0.51 µs
0.63 µs
Use the XIC instruction to determine if the addressed bit is on. Use the XIO
instruction to determine if the addressed bit is off.
XIO
When used on a rung, the bit address being examined can correspond to the status of
real world input devices connected to the base unit or expansion I/O, or internal
addresses (data or function files). Examples of devices that turn on or off:
•
a push button wired to an input (addressed as I1:0/4)
•
an output wired to a pilot light (addressed as O0:0/2)
•
a timer controlling a light (addressed as T4:3/DN)
•
a bit in the bit file (addressed as B3/16)
The instructions operate as follows:
Table 12-2: XIO and XIC Instruction Operation
Rung State
True
True
False
12-2
Addressed Bit
Off
On
--
XIC Instruction
Returns a False
Returns a True
instruction is not evaluated
XIO Instruction
Returns a True
Returns a False
instruction is not evaluated
Relay-Type (Bit) Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 12-3: XIC and XIO Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Operand Bit
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • •
• • •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
12-3
MicroLogix 1500 Programmable Controllers User Manual
OTE - Output Energize
Instruction Type: output
Table 12-4: Execution Time for the OTE Instructions
When Rung Is:
True
False
1.49 µs
0.98 µs
Use an OTE instruction to turn a bit location on when rung conditions are evaluated as
true and off when the rung is evaluated as false. An example of a device that turns on
or off is an output wired to a pilot light (addressed as O0:0/4). OTE instructions are
reset (turned OFF) when:
•
You enter or return to the program or remote program mode or power is restored.
•
The OTE is programmed within an inactive or false Master Control Reset (MCR)
zone.
Note:
12-4
A bit that is set within a subroutine using an OTE instruction remains set
until the OTE is scanned again.
!
ATTENTION: If you enable interrupts during the program scan via
an OTL, OTE, or UIE, this instruction must be the last instruction
executed on the rung (last instruction on last branch). It is
recommended this be the only output instruction on the rung.
!
ATTENTION: Never use an output address at more than one place
in your logic program. Always be fully aware of the load represented
by the output coil.
Relay-Type (Bit) Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 12-5: OTE Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Destination Bit
Address
Function Files
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • •
•
• • •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
OTL - Output Latch
OTU - Output Unlatch
Instruction Type: output
Table 12-6: Execution Time for the OTL and OTU Instructions
Instruction
OTL
OTU
When Rung Is:
True
1.06 µs
1.02 µs
False
0.00 µs
0.00 µs
The OTL and OTU instructions are retentive output instructions. OTL turns on a bit,
while OTU turns off a bit. These instructions are usually used in pairs, with both
instructions addressing the same bit.
!
ATTENTION: If you enable interrupts during the program scan via
an OTL, OTE, or UIE, this instruction must be the last instruction
executed on the rung (last instruction on last branch). It is
recommended this be the only output instruction on the rung.
12-5
MicroLogix 1500 Programmable Controllers User Manual
Since these are latching outputs, once set (or reset), they remain set (or reset)
regardless of the rung condition.
!
ATTENTION: In the event of a power loss, any OTL controlled bit
(including field devices) energizes with the return of power if the OTL
bit was set when power was lost.
!
ATTENTION: Under fatal error conditions, physical outputs are
turned off. Once the error conditions are cleared, the controller resumes
operation using the data table value.
Addressing Modes and File Types can be used as shown in the following table:
Table 12-7: OTL and OTU Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Operand Bit
Address
Function Files
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• • • • • • • • • • • •
•
• • •
1. See Important note about indirect addressing.
Important:
12-6
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
Relay-Type (Bit) Instructions
ONS - One Shot
Instruction Type: input
Table 12-8: Execution Time for the ONS Instructions
When Rung Is:
True
False
1.38 µs
1.85 µs
The ONS instruction is a retentive input instruction that triggers an event to occur one
time. After the false-to-true rung transition, the ONS instruction remains true for one
program scan. The output then turns OFF and remains OFF until the logic preceding
the ONS instruction is false (this re-activates the ONS instruction).
The ONS Storage Bit is the bit address that remembers the rung state from the
previous scan. This bit is used to remember the false-to-true rung transition.
Table 12-9: ONS Instruction Operation
Rung Transition
false-to-true (one scan)
true-to-true
true-to-false, false-to-false
Storage Bit
storage bit is set
storage bit remains set
storage bit is cleared
Rung State after Execution
true
false
false
Addressing Modes and File Types can be used as shown in the following table:
Table 12-10: ONS Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Data Files
Parameter
Storage Bit
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
N7:1
ONS
0
•
•
•
•
12-7
MicroLogix 1500 Programmable Controllers User Manual
OSR - One Shot Rising
OSF - One Shot Falling
Instruction Type: output
Table 12-11: Execution Time for the OSR and OSF Instructions
Instruction
OSR
OSF
When Rung Is:
True
False
2.71 µs
2.43 µs
1.88 µs
3.01 µs
Use the OSR and OSF instructions to trigger an event to occur one time. These
instructions trigger an event based on a change of rung state, as follows:
•
Use the OSR instruction when an event must start based on the false-to-true
(rising edge) change of state of the rung.
•
Use the OSF instruction when an event must start based on the true-to-false
(falling edge) change of state of the rung.
These instructions use two parameters, Storage Bit and Output Bit.
•
Storage Bit - This is the bit address that remembers the rung state from the
previous scan.
•
Output Bit - This is the bit address which is set based on a false-to-true (OSR) or
true-to-false (OSF) rung transition. The Output Bit is set for one program scan.
To re-activate the OSR, the rung must become false. To re-activate the OSF, the rung
must become true.
Table 12-12: OSR Storage and Output Bit Operation
Rung State Transition
false-to-true (one scan)
true-to-true
true-to-false and false-to-false
Storage Bit
bit is set
bit is set
bit is reset
Output Bit
bit is set
bit is reset
bit is reset
Table 12-13: OSF Storage and Output Bits Operation
Rung State Transition
true-to-false (one scan)
false-to-false
12-8
Storage Bit
bit is reset
bit is reset
Output Bit
bit is set
bit is reset
Relay-Type (Bit) Instructions
Table 12-13: OSF Storage and Output Bits Operation
Rung State Transition
false-to-true and true-to-true
Storage Bit
bit is set
Output Bit
bit is reset
Addressing Modes and File Types can be used as shown in the following table:
Table 12-14: OSR and OSF Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Storage Bit
Output Bit
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
•
•
• • • •
•
•
•
•
12-9
MicroLogix 1500 Programmable Controllers User Manual
12-10
Timer and Counter Instructions
13
Timer and Counter Instructions
Timers and counters are output instructions that let you control operations based on
time or a number of events. The following Timer and Counter Instructions are
described in this chapter:
Instruction
Used To:
Page
TON - Timer, On-Delay
Delay turning on an output on a true rung
13-4
TOF - Timer, Off-Delay
Delay turning off an output on a false rung
13-5
RTO - Retentive Timer On
Delay turning on an output from a true
rung. The accumulator is retentive.
13-6
CTU - Count Up
Count up
13-10
CTD - Count Down
Count down
13-10
RES - Reset
Reset the RTO and counter’s ACC and
status bits (not used with TOF timers).
13-11
See “HSL - High Speed Counter Load” on page 9-29 for information on the High
Speed Counter function.
Timer Instructions Overview
Timers in a MicroLogix 1500 reside in a timer file. A timer file can be assigned as any
unused data file. When a data file is used as a timer file, each timer element within the
file has three sub-elements. These sub-elements are:
•
Status/Reserved
•
Preset - This is the value that the timer must reach before the timer times out.
When the accumulator reaches this value, the DN status bit is set (TON and RTO
only). The preset data range is from 0 to 32767. The minimum required update
interval is 2.55 seconds regardless of the timebase.
•
Accumulator - The accumulator counts the Timebase intervals. It represents
elapsed time. The accumulator data range is from 0 to 32767.
13-1
MicroLogix 1500 Programmable Controllers User Manual
Timers can be set to any one of three time bases:
Table 13-1: Timer Base Settings
Time Base
Timing Range
0.001 seconds
0 - 32.767 seconds
0.01 seconds
0 - 327.67 seconds
1.00 seconds
0 - 32,767 seconds
Each timer address is made of a 3-word element. Word 0 is the control word, word 1
stores the preset value, and word 2 stores the accumulated value.
Table 13-2: Timer File
Bit
Word
14 13 12 11 10
EN TT DN
15
Word 0
9
8
7
6
Word 1
Preset Value
Word 2
Accumulated Value
5
4 3 2
Internal Use
1
0
EN = Timer Enable Bit
TT = Timer Timing Bit
DN = Timer Done Bit
Addressing Modes and File Types can be used as shown in the following table:
Table 13-3: Timer Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files1
Timer
Timebase
Preset
Accumulator
•
•
•
•
•
•
•
•
•
•
•
•
1. Valid for Timer Files only.
Note:
13-2
Use an RES instruction to reset a timer’s accumulator and status bits.
Timer and Counter Instructions
Timer Accuracy
Timer accuracy refers to the length of time between the moment a timer instruction is
enabled and the moment the timed interval is complete.
Table 13-4: Timer Accuracy
Time Base
Accuracy
0.001 seconds
-0.001 to 0.00
0.01 seconds
-0.01 to 0.00
1.00 seconds
-1.00 to 0.00
If your program scan can exceed 2.5 seconds, repeat the timer instruction on a
different rung (identical logic and 50% away from this rung) run so that the rung is
scanned within these limits.
Using the enable bit (EN) of a timer is an easy way to repeat its complex conditional
logic at another rung in your ladder program.
Note:
Timing could be inaccurate if Jump (JMP), Label (LBL), Jump to Subroutine
(JSR), or Subroutine (SBR) instructions skip over the rung containing a
timer instruction while the timer is timing. If the skip duration is within 2.5
seconds, no time will be lost; if the skip duration exceeds 2.5 seconds, an
undetectable timing error occurs. When using subroutines, a timer must be
scanned at least every 2.5 seconds to prevent a timing error.
13-3
MicroLogix 1500 Programmable Controllers User Manual
TON - Timer, On-Delay
Instruction Type: output
Table 13-5: Execution Time for the TON Instructions
Instruction
TON
When Rung Is:
True
False
15.48 µs
1.14 µs
Use the TON instruction to delay turning on an output. The TON instruction begins to
count timebase intervals when rung conditions become true. As long as rung
conditions remain true, the timer increments its accumulator until the preset value is
reached. When the accumulator equals the preset, timing stops.
The accumulator is reset (0) when rung conditions go false, regardless of whether the
timer has timed out. TON timers are reset on power cycles and mode changes.
Timer instructions use the following status bits:
Table 13-6: Timer Status Bits, Timer Word 0 (Data File 4 is configured as a timer file for this example.)
Bit
bit 13 - T4:0/DN
bit 14 - T4:0/TT
DN - timer done
TT - timer timing
bit15 - T4:0/EN
EN - timer enable
13-4
Is Set When:
And Remains Set Until One of the
Following Occurs:
accumulated value ≥ preset value rung state goes false
rung state is true and
• rung state goes false
accumulated value < preset value • DN bit is set
rung state is true
rung state goes false
Timer and Counter Instructions
TOF - Timer, Off-Delay
Instruction Type: output
Table 13-7: Execution Time for the TOF Instructions
Instruction
TOF
When Rung Is:
True
False
1.85 µs
12.32 µs
Use the TOF instruction to delay turning off an output. The TOF instruction begins to
count timebase intervals when rung conditions become false. As long as rung
conditions remain false, the timer increments its accumulator until the preset value is
reached.
The accumulator is reset (0) when rung conditions go true, regardless of whether the
timer has timed out. TOF timers are reset on power cycles and mode changes.
Timer instructions use the following status bits:
Table 13-8: Timer Status Bits, Timer Word 0 (Data File 4 is configured as a timer file for this example.)
Bit
Is Set When:
bit 13 - T4:0/DN
DN - timer done
bit 14 - T4:0/TT
TT - timer timing
bit15 - T4:0/EN
EN - timer enable
!
And Remains Set Until One of the
Following Occurs:
rung conditions are true
rung conditions go false and the
accumulated value is greater than or equal to
the preset value
rung conditions are false and the rung conditions go true or when the done bit
accumulated value is less than the is reset
preset value
rung conditions are true
rung conditions go false
ATTENTION: Because the RES instruction resets the accumulated
value and status bits, do not use the RES instruction to reset a timer
address used in a TOF instruction. If the TOF accumulated value and
status bits are reset, unpredictable machine operation or injury to
personnel may occur.
13-5
MicroLogix 1500 Programmable Controllers User Manual
RTO - Retentive Timer On
Instruction Type: output
Table 13-9: Execution Time for the RTO Instructions
Instruction
RTO
When Rung Is:
True
False
15.73 µs
1.85 µs
Use the RTO instruction to delay turning “on” an output. The RTO begins to count
timebase intervals when the rung conditions become true. As long as the rung
conditions remain true, the timer increments its accumulator until the preset value is
reached. The RTO retains the accumulated value when the following occur:
•
rung conditions become false
•
you change the processor mode from run or test to program
•
the processor loses power
•
a fault occurs
When you return the processor to the RUN or TEST mode, and/or the rung conditions
go true, timing continues from the retained accumulated value. RTO timers are
retained through power cycles and mode changes.
Timer instructions use the following status bits:
Table 13-10: Counter Status Bits, Timer Word 0 (Data File 4 is configured as a timer file for this example.)
Bit
Is Set When:
bit 13 - T4:0/DN
bit 14 - T4:0/TT
DN - timer done
TT - timer timing
bit15 - T4:0/EN
EN - timer enable
And Remains Set Until One of the
Following Occurs:
accumulated value ≥ preset value the appropriate RES instruction is enabled
rung state is true and
• rung state goes false, or
accumulated value < preset value • DN bit is set
rung state is true
rung state goes false
To reset the accumulator of a retentive timer, use an RES instruction see
“RES - Reset” on page 13-11.
13-6
Timer and Counter Instructions
How Counters Work
The figure below demonstrates how a counter works. The count value must remain in
the range of -32,768 to +32,767. If the count value goes above +32,767, the counter
status overflow bit (OV) is set (1). If the count goes below -32,768, the counter status
underflow bit (UN) is set (1). A reset (RES) instruction is used to reset (0) the counter.
-32,768
0
+32,768
Count Up
Counter Accumulator Value
Count Down
Underflow
Overflow
Using the CTU and CTD Instructions
Counter instructions use the following parameters:
•
Counter - This is the address of the counter within the data file. All counters are 3word data elements. Word 0 contains the Status Bits, Word 1 contains the Preset
and Word 2 contains the Accumulated Value.
Word
Word 0
Bit
14 13 12 11 10
CU CD DN OV UN
15
9
8
7
6
Word 1
Preset Value
Word 2
Accumulated Value
5
4 3 2
Not Used
1
0
CU = Count Up Enable Bit
CD = Count Down Enable Bit
DN = Count Done Bit
OV = Count Overflow Bit
UN = Count Underflow Bit
•
Preset - When the accumulator reaches this value, the DN bit is set. The preset
data range is from -32768 to 32767.
13-7
MicroLogix 1500 Programmable Controllers User Manual
•
Accumulator - The accumulator contains the current count. The accumulator data
range is from -32768 to 32767.
The accumulated value is incremented (CTU) or decremented (CTD) on each
false-to-true rung transition. The accumulated value is retained when the rung
condition again becomes false, and when power is cycled on the controller. The
accumulated count is retained until cleared by a reset (RES) instruction that has
the same address as the counter.
Note:
The counter continues to count when the accumulator is greater than the
CTU preset and when the accumulator is less than the CTD preset.
Addressing Modes and File Types can be used as shown in the following table:
Table 13-11: CTD and CTU Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Counter
Preset
Accumulator
•
•
•
1. Valid for Counter Files only.
13-8
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files1
•
•
•
•
•
•
Timer and Counter Instructions
Using Counter File Status Bits
Like the accumulated value, the counter status bits are also retentive until reset.
Table 13-12: CTU Instruction Counter Status Bits, Counter Word 0 (Data File 5 is configured as a timer file for this example.)
Bit
bit 12 - C5:0/OV
OV - overflow indicator
bit 13 - C5:0/DN
DN - done indicator
bit15 - C5:0/CU
CU - count up enable
Is Set When:
And Remains Set Until One of the
Following Occurs:
the accumulated value wraps from a RES instruction with the same address as
+32,767 to -32,768 and continues the CTU instruction is enabled
to count up
accumulated value ≥ preset value • accumulated value < preset value or,
• a RES instruction with the same address
as the CTU instruction is enabled
rung state is true
• rung state is false
• a RES instruction with the same address
as the CTU instruction is enabled
Table 13-13: CTD Instruction Counter Status Bits, Counter Word 0 (Data File 5 is configured as a timer file for this example.)
Bit
bit 11 - C5:0/UN
UN - underflow indicator
bit 13 - C5:0/DN
DN - done indicator
bit 14 - C5:0/CD
CD - count down enable
Is Set When:
And Remains Set Until One of the
Following Occurs:
the accumulated value wraps from a RES instruction with the same address as
-32,768 to +32,767 and continues the CTD instruction is enabled
to count down
accumulated value ≥ preset value • accumulated value < preset value or,
• a RES instruction with the same address
as the CTU instruction is enabled
rung state is true
• rung state is false
• a RES instruction with the same address
as the CTD instruction is enabled
13-9
MicroLogix 1500 Programmable Controllers User Manual
CTU - Count Up
CTD - Count Down
Instruction Type: output
Table 13-14: Execution Time for the CTU and CTD Instructions
Instruction
Data Size
CTU
CTD
word
word
When Rung Is:
True
False
7.80 µs
8.40 µs
8.30 µs
8.30 µs
The CTU and CTD instructions are used to increment or decrement a counter at each
false-to-true rung transition. When the CTU rung makes a false-to-true transition, the
accumulated value is incremented by one count. The CTD instruction operates the
same, except the count is decremented.
Note:
13-10
If the signal is coming from a field device wired to an input on the controller,
the on and off duration of the incoming signal must not be more than twice
the controller scan time (assuming 50% duty cycle). This condition is
needed to enable the counter to detect false-to-true transitions from the
incoming device.
Timer and Counter Instructions
RES - Reset
Instruction Type: output
Table 13-15: Execution Time for the RES Instructions
Instruction
Data Size
RES
word
When Rung Is:
True
False
4.94 µs
0.00 µs
The RES instruction resets timers, counters, and control elements. When the RES
instruction is executed, it resets the data defined by the RES instruction.
The RES instruction has no effect when the rung state is false. The following table
shows which elements are modified:
Table 13-16: RES Instruction Operation
When using a RES instruction with a:
Timer Element
Counter Element
The controller resets the:
The controller resets the:
ACC value to 0
ACC value to 0
DN bit
OV bit
TT bit
UN bit
EN bit
DN bit
CU bit
CD bit
!
Control Element
The controller resets the:
POS value to 0
EN bit
EU bit
DN bit
EM bit
ER bit
UL bit
ATTENTION: Because the RES instruction resets the accumulated
value and status bits, do not use the RES instruction to reset a timer
address used in a TOF instruction. If the TOF accumulated value and
status bits are reset, unpredictable machine operation or injury to
personnel may occur.
13-11
MicroLogix 1500 Programmable Controllers User Manual
Addressing Modes and File Types can be used as shown in the following table:
Table 13-17: RES Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Structure
13-12
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
•
•
Compare Instructions
14
Compare Instructions
Use these input instructions when you want to compare values of data.
Instruction
Used To:
Page
EQU - Equal
Test whether two values are equal (=)
14-3
NEQ - Not Equal
Test whether one value is not equal to a
second value (≠)
14-3
LES - Less Than
Test whether one value is less than a
second value (<)
14-4
LEQ - Less Than or Equal To
Test whether one value is less than or
equal to a second value (≤)
14-5
GRT - Greater Than
Test whether one value is greater than a
second value (>)
14-4
GEQ - Greater Than or Equal To
Test whether one value is greater than or
equal to a second value (≥)
14-5
MEQ - Mask Compare for Equal
Test portions of two values to see whether
they are equal
14-6
LIM - Limit Test
Test whether one value is within the range
of two other values
14-8
14-1
MicroLogix 1500 Programmable Controllers User Manual
Using the Compare Instructions
Most of the compare instructions use two parameters, Source A and Source B (MEQ
and LIM have an additional parameter, and are described later in this chapter). Both
sources cannot be immediate values. The valid data ranges for these instructions are:
•
-32768 to 32767 (word)
•
-2,147,483,648 to 2,147,483,647 (long word)
Addressing Modes and File Types can be used as shown in the following table:
Table 14-1: Compare Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source A
Source B
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• •
• •
1. See Important note about indirect addressing.
Important:
14-2
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
Compare Instructions
EQU - Equal
NEQ - Not Equal
Instruction Type: input
Table 14-2: Execution Time for the EQU and NEQ Instructions
Instruction
Data Size
EQU
word
long word
word
long word
NEQ
When Rung Is:
True
False
1.30 µs
0.94 µs
1.41 µs
2.27 µs
1.30 µs
0.94 µs
1.80 µs
2.20 µs
The EQU instruction is used to test whether one value is equal to a second value. The
NEQ instruction is used to test whether one value is not equal to a second value.
Table 14-3: EQU and NEQ Instruction Operation
Instruction
EQU
NEQ
Relationship of Source Values
A=B
A≠B
A=B
A≠B
Resulting Rung State
true
false
false
true
14-3
MicroLogix 1500 Programmable Controllers User Manual
GRT - Greater Than
LES - Less Than
Instruction Type: input
Table 14-4: Execution Time for the GRT and LES Instructions
Instruction
Data Size
GRT
word
long word
word
long word
LES
When Rung Is:
True
False
1.30 µs
0.94 µs
2.27 µs
2.59 µs
1.22 µs
1.02 µs
2.59 µs
2.27 µs
The GRT instruction is used to test whether one value is greater than a second value.
The LES instruction is used to test whether one value is less than a second value.
Table 14-5: GRT and LES Instruction Operation
Instruction
GRT
LES
14-4
Relationship of Source Values
A>B
A≤B
A≥B
A<B
Resulting Rung State
true
false
false
true
Compare Instructions
GEQ - Greater Than or Equal To
LEQ - Less Than or Equal To
Instruction Type: input
Table 14-6: Execution Time for the GEQ and LEQ Instructions
Instruction
Data Size
GEQ
word
long word
word
long word
LEQ
When Rung Is:
True
False
1.30 µs
0.94 µs
2.27 µs
2.59 µs
1.30 µs
1.02 µs
2.59 µs
2.27 µs
The GEQ instruction is used to test whether one value is greater than or equal to a
second value. The LEQ instruction is used to test whether one value is less than or
equal to a second value.
Table 14-7: GEQ and LEQ Instruction Operation
Instruction
GEQ
LEQ
Relationship of Source Values
A≥B
A<B
A>B
A≤B
Resulting Rung State
true
false
false
true
14-5
MicroLogix 1500 Programmable Controllers User Manual
MEQ - Mask Compare for Equal
Instruction Type: input
Table 14-8: Execution Time for the MEQ Instructions
Data Size
When Rung Is:
True
False
2.07 µs
1.97 µs
3.37 µs
2.58 µs
word
long word
The MEQ instruction is used to compare whether one value (source) is equal to a
second value (compare) through a mask. The source and the compare are logically
ANDed with the mask. Then, these results are compared to each other. If the resulting
values are equal, the rung state is true. If the resulting values are not equal, the rung
state is false. For example:
Source:
1 1 1 1 1 0 1 0 0 0 0 0 1
Mask:
1 1 0 0 1 1 1 1 1 1 0 0 0
Intermediate Result:
1 1 0 0 1 0 1 0 0 0 0 0 0
Comparison of the Intermediate Results: not equal
1
0
0
1
0
0
Compare:
1 1 1 1 1 1
Mask:
1 1 1 0 0 1 1
Intermediate Result:
0 1 1 0 0 1 1
0
1
1
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
The source, mask, and compare values must all be of the same data size (either word
or long word). The data ranges for mask and compare are:
•
-32768 to 32767 (word)
•
-2,147,483,648 to 2,147,483,647 (long word)
The mask is displayed as a hexadecimal unsigned value from 0000 to FFFF FFFF.
14-6
Compare Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 14-9: MEQ Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Mask
Compare
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • •
• •
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• •
• •
• •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
14-7
MicroLogix 1500 Programmable Controllers User Manual
LIM - Limit Test
Instruction Type: input
Table 14-10: Execution Time for the LIM Instructions
Data Size
word
long word
When Rung Is:
True
False
6.43 µs
5.79 µs
12.41 µs
11.59 µs
The LIM instruction is used to test for values within or outside of a specified range.
The LIM instruction is evaluated based on the Low Limit, Test, and High Limit values
as shown in the following table.
Table 14-11: LIM Instruction Operation Based on Low Limit, Test, and High Limit Values
When:
And:
Rung State
Low Limit ≤ High Limit
Low Limit ≤ Test ≤ High Limit
true
Low Limit ≤ High Limit
Test < Low Limit or Test > High Limit
false
High Limit < Low Limit
High Limit < Test < Low Limit
false
High Limit < Low Limit
Test ≥ High Limit or Test ≤ Low Limit
true
The Low Limit, Test, and High Limit values can be word addresses or constants,
restricted to the following combinations:
•
If the Test parameter is a constant, both the Low Limit and High Limit parameters
must be word or long word addresses.
•
If the Test parameter is a word or long word address, the Low Limit and High
Limit parameters can be either a constant, a word, or a long word address. But the
Low Limit and High Limit parameters cannot both be constants.
When mixed-sized parameters are used, all parameters are put into the format of the
largest parameter. For instance, if a word and a long word are used, the word is
converted to a long word.
The data ranges are:
14-8
•
-32768 to 32767 (word)
•
-2,147,483,648 to 2,147,483,647 (long word)
Compare Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 14-12: LIM Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Low Limit
Test
High Limit
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• •
• •
• •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
14-9
MicroLogix 1500 Programmable Controllers User Manual
14-10
Math Instructions
15
Math Instructions
Use these output instructions to perform computations using an expression or a
specific arithmetic instruction.
Instruction
Used To:
Page
ADD - Add
Add two values
15-4
SUB - Subtract
Subtract two values
15-4
MUL - Multiply
Multiply two values
15-5
DIV - Divide
Divide one value by another
15-5
NEG - Negate
Change the sign of the source value and
place it in the destination
15-6
CLR - Clear
Set all bits of a word to zero
15-6
SQR - Square Root
Find the square root of a value
15-10
SCL - Scale
Scale a value
15-7
SCP - Scale with Parameters
Scale a value to a range determined by
creating a linear relationship
15-8
15-1
MicroLogix 1500 Programmable Controllers User Manual
Using the Math Instructions
Most math instructions use three parameters, Source A, Source B, and Destination
(additional parameters are described where applicable, later in this chapter). The
mathematical operation is performed using both Source values. The result is stored in
the Destination.
When using math instructions, observe the following:
•
Source and Destination can be different data sizes. Sources are evaluated at the
highest precision (word or long word) of the operands. Then the result is
converted to the size of the destination. If the signed value of the Source does not
fit in the Destination, the overflow shall be handled as follows:
v If the Math Overflow Selection Bit is clear, a saturated result is stored in the
Destination. If the Source is positive, the Destination is +32767 (word) or
+2,147,483,647 (long word). If the result is negative, the Destination is -32768
(word) or -2,147,483,648 (long word).
v If the Math Overflow Selection Bit is set, the unsigned truncated value of the
Source is stored in the Destination.
•
Sources can be constants or an address, but both sources cannot be constants.
•
Valid constants are -32768 to 32767 (word) and -2,147,483,648 to 2,147,483,647
(long word).
Addressing Modes and File Types can be used as shown in the following table:
Table 15-1: Math Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source A
Source B
Destination
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • •
• •
•
• •
• •
• •
1. See Important note about indirect addressing.
Important:
15-2
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
Math Instructions
Updates to Math Status Bits
After a math instruction is executed, the arithmetic status bits in the status file are
updated. The arithmetic status bits are in word 0 in the processor status file (S2).
Table 15-2: Math Status Bits
S:0/0
S:0/1
S:0/2
S:0/3
S:2/14
S:5/0
With this Bit:
Carry
Overflow
The Controller:
sets if carry is generated; otherwise resets
sets when the result of a math instruction does not fit into the
destination, otherwise resets
Zero Bit
sets if result is zero, otherwise resets
Sign Bit
sets if result is negative (MSB is set), otherwise resets
1
Math Overflow Selected examines the state of this bit to determine the value of the result
when an overflow occurs
1
sets if the Overflow Bit is set, otherwise resets
Overflow Trap
1. Control bits.
Overflow Trap Bit, S:5/0
Minor error bit (S:5/0) is set upon detection of a mathematical overflow or division by
zero. If this bit is set upon execution of an END statement or a Temporary End (TND)
instruction, the recoverable major error code 0020 is declared.
In applications where a math overflow or divide by zero occurs, you can avoid a
controller fault by using an unlatch (OTU) instruction with address S:5/0 in your
program. The rung must be between the overflow point and the END or TND
statement.
15-3
MicroLogix 1500 Programmable Controllers User Manual
ADD - Add
SUB - Subtract
Instruction Type: output
Table 15-3: Execution Time for the ADD and SUB Instructions
Instruction
Data Size
ADD
word
long word
word
long word
SUB
When Rung Is:
True
False
2.12 µs
0.00 µs
0.00 µs
10.82 µs
3.06 µs
0.00 µs
11.22 µs
0.00 µs
Use the ADD instruction to add one value to another value (Source A + Source B) and
place the sum in the Destination.
Use the SUB instruction to subtract one value from another value (Source A - Source
B) and place the result in the Destination.
15-4
Math Instructions
MUL - Multiply
DIV - Divide
Instruction Type: output
Table 15-4: Execution Time for the MUL and DIV Instructions
Instruction
Data Size
MUL
word
long word
word
long word
DIV
When Rung Is:
True
False
5.88 µs
0.00 µs
0.00 µs
28.55 µs
9.95 µs
0.00 µs
32.92 µs
0.00 µs
Use the MUL instruction to multiply one value by another value (Source A x Source
B) and place the result in the Destination.
Use the DIV instruction to divide one value by another value (Source A/Source B)
and place the result in the Destination. If the Sources are single words and the
Destination is directly addressed to S:13 (math register), then the quotient is stored in
S:14 and the remainder is stored in S:13.
15-5
MicroLogix 1500 Programmable Controllers User Manual
NEG - Negate
Instruction Type: output
Table 15-5: Execution Time for the NEG Instruction
Data Size
word
long word
When Rung Is:
True
False
2.35 µs
0.00 µs
10.18 µs
0.00 µs
Use the NEG instruction to change the sign of the Source and place the result in the
Destination.
CLR - Clear
Instruction Type: output
Table 15-6: Execution Time for the CLR Instruction
Data Size
word
long word
When Rung Is:
True
False
1.18 µs
0.00 µs
5.49 µs
0.00 µs
Use the CLR instruction to set the Destination to a value of zero.
15-6
Math Instructions
SCL - Scale
Instruction Type: output
Table 15-7: Execution Time for the SCL Instruction
When Rung Is:
True
False
9.30 µs
0.00 µs
The SCL instruction causes the value at the Source address to be multiplied by the
Rate (slope) value. The resulting value is added to the Offset and the rounded result is
placed in the Destination.
The scaled value = [(rate x source)/10000] + offset.
Rate and Offset can both be immediate values. The data range for rate and offset is
-32768 to 32767.
Addressing Modes and File Types can be used as shown in the following table:
Table 15-8: SCL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Rate
Offset
Destination
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
• •
• •
•
•
•
•
•
•
•
•
•
•
•
•
• •
• • •
• • •
• •
•
•
•
•
15-7
MicroLogix 1500 Programmable Controllers User Manual
SCP - Scale with Parameters
Instruction Type: output
Table 15-9: Execution Time for the SCP Instruction
Data Size
word
long word
When Rung Is:
True
False
28.44 µs
0.00 µs
45.59 µs
0.00 µs
The SCP instruction produces a scaled output value that has a linear relationship
between the input and scaled values.
This instruction solves the equation listed below to determine scaled output.
y = m(x - x0) + y0, where:
•
y = scaled output
•
x = input (Input)
•
m = slope = ∆y/∆x
•
∆y = y1 - y0
•
∆x = x1 - x0
•
x0 = input start (Input min)
•
x1 = input end (Input max)
•
y0 = scaled start (Scaled min)
•
y1 = scaled end (Scaled max)
The data ranges for Start and End values are:
15-8
•
-32768 to 32767 (word)
•
-2,147,483,648 to 2,147,483,647 (long word).
Math Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 15-10: SCP Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Input (x)
Input Start (x0)
Input End (x1)
• • • • • • • • • • • • • • • • •
• •
• • • •
• •
• • • •
• •
• •
Scaled Output (y) • •
Scaled Start (y0)
Scaled End (y1)
Function Files
Address
Mode1
Address
Level
• •
• • •
• • •
• •
• •
• •
• • •
• • •
• •
• •
• •
• •
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • •
• • • •
• • • • •
• •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
15-9
MicroLogix 1500 Programmable Controllers User Manual
SQR - Square Root
Instruction Type: output
Table 15-11: Execution Time for the SQR Instruction
Data Size
When Rung Is:
True
False
22.51 µs
0.00 µs
26.58 µs
0.00 µs
word
long word
The SQR instruction calculates the square root of the absolute value of the source and
places the rounded result in the destination.
The data ranges for the source is -32768 to 32767 (word) and -2,147,483,648 to
2,147,483,647 (long word). The Carry Math Status Bit is set if the source is negative.
See “Updates to Math Status Bits” on page 15-3 for more information.
Table 15-12: SQR Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Destination
15-10
Function Files
Address
Mode
Address
Level
• • •
• •
• •
• •
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• •
•
• • • •
• • • •
Conversion Instructions
16
Conversion Instructions
The conversion instructions multiplex and de-multiplex data and perform conversions
between binary and decimal values.
Instruction
Used To:
Page
DCD - Decode 4 to 1-of-16
Decodes a 4-bit value (0 to 15), turning
on the corresponding bit in the 16-bit
destination.
16-3
ENC - Encode 1-of-16 to 4
Encodes a 16-bit source to a 4-bit value.
Searches the source from the lowest to
the highest bit, and looks for the first set
bit. The corresponding bit position is
written to the destination as an integer.
16-4
FRD - Convert From Binary Coded
Decimal
Converts the BCD source value to an
integer and stores it in the destination.
16-6
TOD - Convert to Binary Coded
Decimal
Converts the integer source value to BCD
format and stores it in the destination.
16-10
16-1
MicroLogix 1500 Programmable Controllers User Manual
Using Decode and Encode Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 16-1: Conversion Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Destination
16-2
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• •
•
• • •
• • •
• •
• •
•
•
Conversion Instructions
DCD - Decode 4 to 1-of-16
Instruction Type: output
Table 16-2: Execution Time for the DCD Instruction
When Rung Is:
True
False
1.68 µs
0.00 µs
The DCD instruction uses the lower four bits of the source word to set one bit of the
destination word. All other bits in the destination word are cleared. The DCD
instruction converts the values as shown in the table below:
Table 16-3: Decode 4 to 1-of-16
Source Bits
15 to 04 03 02
x
0
0
x
0
0
x
0
0
x
0
0
x
0
1
x
0
1
x
0
1
x
0
1
x
1
0
x
1
0
x
1
0
x
1
0
x
1
1
x
1
1
x
1
1
x
1
1
x = not used
01
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
00
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
15
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
14
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
13
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
12
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
11
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
10
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
Destination Bits
09 08 07 06
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
05
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
04
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
03
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
02
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
01
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
00
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
16-3
MicroLogix 1500 Programmable Controllers User Manual
ENC - Encode 1-of-16 to 4
Instruction Type: output
Table 16-4: Execution Time for the CLR Instruction
When Rung Is:
True
False
6.90 µs
0.00 µs
The ENC instruction searches the source from the lowest to the highest bit, looking
for the first bit set. The corresponding bit position is written to the destination as an
integer. The ENC instruction converts the values as shown in the table below:
Table 16-5: Encode 1-of-16 to 4
15 14 13 12 11 10
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
x
x
x
x
1
0
x
x
x
1
0
0
x
x
1
0
0
0
x
1
0
0
0
0
1
0
0
0
0
0
x = determines the state of the flag
Note:
16-4
09
x
x
x
x
x
x
x
x
x
1
0
0
0
0
0
0
Source Bits
08 07
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
06
x
x
x
x
x
x
1
0
0
0
0
0
0
0
0
0
05
x
x
x
x
x
1
0
0
0
0
0
0
0
0
0
0
04
x
x
x
x
1
0
0
0
0
0
0
0
0
0
0
0
03
x
x
x
1
0
0
0
0
0
0
0
0
0
0
0
0
02
x
x
1
0
0
0
0
0
0
0
0
0
0
0
0
0
01
x
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
00
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Destination Bits
15 to 04 03 02 01
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
0
1
1
0
0
1
1
0
1
0
0
0
1
0
0
0
1
0
1
0
1
0
1
0
1
1
0
0
1
1
0
0
1
1
1
0
1
1
1
00
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
If source is zero, the destination is zero and the math status is zero, the flag is
set to 1.
Conversion Instructions
Updates to Math Status Bits
Table 16-6: Math Status Bits
S:0/0
S:0/1
With this Bit:
Carry
Overflow
S:0/2
S:0/3
Zero Bit
Sign Bit
The Controller:
always resets
sets if more than one bit in the source is set; otherwise resets.
The math overflow bit (S:5/0) is not set.
sets if result is zero, otherwise resets
always resets
16-5
MicroLogix 1500 Programmable Controllers User Manual
FRD - Convert from Binary Coded Decimal (BCD)
Instruction Type: output
Table 16-7: Execution Time for the FRD Instructions
Instruction
When Rung Is:
True
False
12.61 µs
0.00 µs
FRD
The FRD instruction is used to convert the BCD source value to an integer and place
the result in the destination.
Addressing Modes and File Types can be used as shown in the following table:
Table 16-8: FRD Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
Source
• • • • • •
• •
•
Destination
• •
• •
•
• • •
1. See Important note about indirect addressing.
2. See “FRD Instruction Source Operand” on page 16-7.
Important:
16-6
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
2
Conversion Instructions
FRD Instruction Source Operand
The source can be either a word address or the math register.
The maximum BCD source values permissible are:
•
9999 if the source is a word address (allowing only a 4-digit BCD value)
•
32768 if the source is the math register (allowing a 5-digit BCD value with the
lower 4 digits stored in S:13 and the high order digit in S:14).
If the source is the math register, it must be directly addressed as S:13. S:13 is the
only status file element that can be used.
Updates to Math Status Bits
Table 16-9: Math Status Bits
S:0/0
S:0/1
With this Bit:
Carry
Overflow
S:0/2
S:0/3
Zero Bit
Sign Bit
Note:
The Controller:
always resets
sets if non-BCD value is contained at the source or the value to
be converted is greater than 32,767; otherwise resets. On
overflow, the minor error flag is also set.
sets if result is zero, otherwise resets
always resets
Always provide ladder logic filtering of all BCD input devices prior to
performing the FRD instruction. The slightest difference in point-to-point
input filter delay can cause the FRD instruction to overflow due to the
conversion of a non-BCD digit.
S:1
]/[
15
EQU
EQUAL
Source A
Source B
FRD
N7:1
0
I:0.0
0
FROM BCD
Source
Dest
I:0.0
0
N7:2
0
MOV
MOVE
Source
Dest
I:0.0
0
N7:1
0
16-7
MicroLogix 1500 Programmable Controllers User Manual
The two rungs shown cause the controller to verify that the value I:0 remains the same
for two consecutive scans before it will execute the FRD. This prevents the FRD from
converting a non–BCD value during an input value change.
Note:
To convert numbers larger than 9999 BCD, the source must be the Math
Register (S:13). You must reset the Minor Error Bit (S:5.0) to prevent an
error.
Example
The BCD value 32,760 in the math register is converted and stored in N7:0. The
maximum source value is 32767, BCD.
MPS displays S:13 and
S:14 in BCD.
S:14
0000 0000 0000 0011
15
0
0
0
0
3
3
S:13
0010 0111 0110 0000
15
0 5-digit BCD
2
7
6
0
2
7
6
0
N7:0 Decimal 0111 1111 1111 1000
You should convert BCD values to integer before you manipulate them in your ladder
program. If you do not convert the values, the controller manipulates them as integers
and their value may be lost.
Note:
16-8
If the math register (S:13 and S:14) is used as the source for the FRD
instruction and the BCD value does not exceed 4 digits, be sure to clear word
S:14 before executing the FRD instruction. If S:14 is not cleared and a value
is contained in this word from another math instruction located elsewhere in
the program, an incorrect decimal value will be placed in the destination
word.
Conversion Instructions
Clearing S:14 before executing the FRD instruction is shown below:
0001 0010 0011 0100
S:13 and S:14 are
displayed in BCD format.
0000 0100 1101 0010
When the input condition I:0/1 is set (1), a BCD value (transferred from a 4–digit
thumbwheel switch for example) is moved from word N7:2 into the math register.
Status word S:14 is then cleared to make certain that unwanted data is not present
when the FRD instruction is executed.
16-9
MicroLogix 1500 Programmable Controllers User Manual
TOD - Convert to Binary Coded Decimal (BCD)
Instruction Type: output
Table 16-10: Execution Time for the TOD Instructions
Instruction
TOD
When Rung Is:
True
False
14.64 µs
0.00 µs
The TOD instruction is used to convert the integer source value to BCD and place the
result in the destination.
Addressing Modes and File Types can be used as shown in the following table:
Table 16-11: TOD Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Destination
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• • •
• • • • • •
• •
• •
•
•
1. See Important note about indirect addressing.
2. See “TOD Instruction Destination Operand” on page 16-11.
Important:
16-10
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
2
Conversion Instructions
TOD Instruction Destination Operand
The destination can be either a word address or math register.
The maximum values permissible once converted to BCD are:
•
9999 if the destination is a word address (allowing only a 4-digit BCD value)
•
32768 if the destination is the math register (allowing a 5-digit BCD value with
the lower 4 digits stored in S:13 and the high order digit in S:14).
If the destination is the math register, it must be directly addressed as S:13. S:13 is the
only status file element that can be used.
Updates to Math Status Bits
Table 16-12: Math Status Bits
S:0/0
S:0/1
With this Bit:
Carry
Overflow
S:0/2
S:0/3
Zero Bit
Sign Bit
The Controller:
always resets
sets if BCD result is larger than 9999. On overflow, the minor
error flag is also set.
sets if result is zero, otherwise resets
sets if the source word is negative; otherwise resets
Changes to the Math Register
Contains the 5–digit BCD result of the conversion. This result is valid at overflow.
Note:
To convert numbers larger than 9999 decimal, the destination must be the
Math Register (S:13). You must reset the Minor Error Bit (S:5/0) to prevent
an error.
16-11
MicroLogix 1500 Programmable Controllers User Manual
Example
The integer value 9760 stored at N7:3 is converted to BCD and the BCD equivalent is
stored in N7:0. The maximum BCD value is 9999.
MPS displays the destination value in
BCD format.
MSB
16-12
MSB
9
7
6
0
N7:3
Decimal
0010
0110
0010
0000
9
7
6
0
N7:0
4-digit BCD
1001
0111
0110
0000
Logical Instructions
17
Logical Instructions
The logical instructions perform bit-wise logical operations on individual words.
Instruction
Used To:
Page
AND - Bit-Wise AND
Perform an AND operation
17-3
OR - Logical OR
Perform an inclusive OR operation
17-4
XOR - Exclusive OR
Perform an Exclusive Or operation
17-5
NOT - Logical NOT
Perform a NOT operation
17-6
Using Logical Instructions
When using logical instructions, observe the following:
•
Source and Destination must be of the same data size (i.e. all words or all long
words).
•
Source A and Source B can be a constant or an address, but both cannot be
constants.
•
Valid constants are -32768 to 32767 (word) and -2,147,483,648 to 2,147,483,647
(long word).
17-1
MicroLogix 1500 Programmable Controllers User Manual
Addressing Modes and File Types can be used as shown in the following table:
Table 17-1: Logical Instructions Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source A
Source
B2
Destination
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• •
• •
• • • • • • • • • • •
• •
• •
1. See Important note about indirect addressing.
2. Source B does not apply to the NOT instruction. The NOT instruction only has one source value.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
Updates to Math Status Bits
After a logical instruction is executed, the arithmetic status bits in the status file are
updated. The arithmetic status bits are in word 0 bits 0-3 in the processor status file
(S2).
Table 17-2: Math Status Bits
S:0/0
S:0/1
S:0/2
S:0/3
17-2
With this Bit:
Carry
Overflow
Zero Bit
Sign Bit
The Controller:
always resets
always resets
sets if result is zero, otherwise resets
sets if result is negative (MSB is set), otherwise resets
Logical Instructions
AND - Bit-Wise AND
Instruction Type: output
Table 17-3: Execution Time for the AND Instruction
Data Size
When Rung Is:
True
False
2.00 µs
0.00 µs
8.20 µs
0.00 µs
word
long word
The AND instruction performs a bit-wise logical AND of two sources and places the
result in the destination.
Table 17-4: Truth Table for the AND Instruction
Destination = A AND B
Source: A
1 1 1 1
Source: B
1 1 0 0
Destination:
1 1 0 0
1
0
1
0
0
0
0
0
1
1
0
0
1
1
1
1
1
1
0
0
0
0
1
1
1
0
1
0
0
0
0
0
0
0
0
0
For more information, see “Using Logical Instructions” on page 17-1 and “Updates to
Math Status Bits” on page 17-2.
17-3
MicroLogix 1500 Programmable Controllers User Manual
OR - Logical OR
Instruction Type: output
Table 17-5: Execution Time for the OR Instruction
Data Size
When Rung Is:
True
False
2.00 µs
0.00 µs
8.19 µs
0.00 µs
word
long word
The OR instruction performs a logical OR of two sources and places the result in the
destination.
Table 17-6: Truth Table for the OR Instruction
Destination = A OR B
Source: A
1 1 1 1
Source: B
1 1 0 0
Destination:
1 1 1 1
1
0
1
0
0
0
0
0
1
1
0
0
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
1
1
For more information, see “Using Logical Instructions” on page 17-1 and “Updates to
Math Status Bits” on page 17-2.
17-4
Logical Instructions
XOR - Exclusive OR
Instruction Type: output
Table 17-7: Execution Time for the XOR Instruction
Data Size
When Rung Is:
True
False
2.67 µs
0.00 µs
8.81 µs
0.00 µs
word
long word
The XOR instruction performs a logical exclusive OR of two sources and places the
result in the destination.
Table 17-8: Truth Table for the XOR Instruction
Destination = A XOR B
Source: A
1 1 1 1
Source: B
1 1 0 0
Destination:
0 0 1 1
1
0
1
0
0
0
0
0
1
1
0
0
1
1
1
1
1
1
0
0
0
0
1
1
0
1
0
1
1
1
0
0
1
1
1
1
For more information, see “Using Logical Instructions” on page 17-1 and “Updates to
Math Status Bits” on page 17-2.
17-5
MicroLogix 1500 Programmable Controllers User Manual
NOT - Logical NOT
Instruction Type: output
Table 17-9: Execution Time for the NOT Instruction
Data Size
When Rung Is:
True
False
2.20 µs
0.00 µs
7.99 µs
0.00 µs
word
long word
The NOT instruction is used to invert the source bit-by-bit (one’s complement) and
then place the result in the destination.
Table 17-10: Truth Table for the NOT Instruction
Destination = A NOT B
Source:
1 1 1 1
Destination:
0 0 0 0
1
0
1
0
0
0
0
0
1
1
0
0
0
1
0
1
1
1
1
1
0
0
1
1
For more information, see “Using Logical Instructions” on page 17-1 and “Updates to
Math Status Bits” on page 17-2.
17-6
Move Instructions
18
Move Instructions
The move instructions modify and move words.
Instruction
Used to:
Page
MOV - Move
Move the source value to the destination.
18-2
MVM - Masked Move
Move data from a source location to a
selected portion of the destination.
18-4
18-1
MicroLogix 1500 Programmable Controllers User Manual
MOV - Move
Instruction Type: output
Table 18-1: Execution Time for the MOV Instruction
Data Size
word
long word
When Rung Is:
True
False
2.15 µs
0.00 µs
7.18 µs
0.00 µs
The MOV instruction is used to move data from the source to the destination. As long
as the rung remains true, the instruction moves the data each scan.
Using the MOV Instruction
When using the MOV instruction, observe the following:
•
Source and Destination can be different data sizes. The source is converted to the
destination size when the instruction executes. If the signed value of the Source
does not fit in the Destination, the overflow shall be handled as follows:
v If the Math Overflow Selection Bit is clear, a saturated result is stored in the
Destination. If the Source is positive, the Destination is 32767 (word). If the
result is negative, the Destination is -32768.
v If the Math Overflow Selection Bit is set, the unsigned truncated value of the
Source is stored in the Destination.
18-2
•
Source can be a constant or an address.
•
Valid constants are -32768 to 32767 (word) and -2,147,483,648 to 2,147,483,647
(long word).
Move Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 18-2: MOV Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Function Files
Address
Mode1
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • •
• •
•
• •
Source
Destination
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
Updates to Math Status Bits
After a MOV instruction is executed, the arithmetic status bits in the status file are
updated. The arithmetic status bits are in word 0 bits 0-3 in the processor status file
(S2).
Table 18-3: Math Status Bits
S:0/0
S:0/1
S:0/2
S:0/3
S:5/0
With this Bit:
Carry
Overflow
Zero Bit
Sign Bit
Math Overflow Trap Bit1
The Controller:
always resets
sets when an overflow condition is detected, otherwise resets
sets if result is zero, otherwise resets
sets if result is negative (MSB is set), otherwise resets
sets Math Overflow Trap minor error if the Overflow bit is set,
otherwise it remains in last state
1. Control bit.
Note:
If you want to move one word of data without affecting the math flags, use a
copy (COP) instruction with a length of 1 word instead of the MOV
instruction.
18-3
MicroLogix 1500 Programmable Controllers User Manual
MVM - Masked Move
Instruction Type: output
Table 18-4: Execution Time for the MVM Instruction
Data Size
word
long word
When Rung Is:
True
False
7.05 µs
0.00 µs
10.58 µs
0.00 µs
The MVM instruction is used to move data from the source to the destination,
allowing portions of the destination to be masked. The mask bit functions as follows:
Table 18-5: Mask Function for MVM Instruction
Source Bit
1
0
1
0
Mask Bit
0
0
1
1
Destination Bit
last state
last state
1
0
Mask data by setting bits in the mask to zero; pass data by setting bits in the mask to
one. The mask can be a constant, or you can vary the mask by assigning a direct
address. Bits in the Destination that correspond to zeros in the Mask are not altered.
18-4
Move Instructions
Using the MVM Instruction
When using the MVM instruction, observe the following:
•
Source, Mask, and Destination must be of the same data size (i.e. all words or all
long words). An example of masking is shown below for word addressing level:
Bit
Word
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
Destination Before Move
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Source
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Mask (F0F0)
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
Destination After Move
0
1
0
1
1
1
1
1
0
1
0
1
1
1
1
1
Mask data by setting bits in the mask to zero; pass data by setting bits in the mask
to one. The mask can be a constant value, or you can vary the mask by assigning a
direct address. Bits in the destination that correspond to zeros in the mask are not
altered.
•
Valid constants for the mask are -32768 to 32767 (word) and -2,147,483,648 to
2,147,483,647 (long word). The mask is displayed as a hexadecimal unsigned
value from 0000 0000 to FFFF FFFF.
Addressing Modes and File Types can be used as shown in the following table:
Table 18-6: MVM Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Mask
Destination
Function Files
Address
Mode
Address
Level
• •
• • •
• •
• •
• •
• •
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
• •
• • • •
• • • •
• • • •
18-5
MicroLogix 1500 Programmable Controllers User Manual
Updates to Math Status Bits
After a MVM instruction is executed, the arithmetic status bits in the status file are
updated. The arithmetic status bits are in word 0 bits 0-3 in the processor status file
(S2).
Table 18-7: Math Status Bits
S:0/0
S:0/1
S:0/2
S:0/3
18-6
With this Bit:
Carry
Overflow
Zero Bit
Sign Bit
The Controller:
always resets
always resets
sets if destination is zero, otherwise resets
sets if the MSB of the destination is set, otherwise resets
File Instructions
19
File Instructions
The file instructions perform operations on file data.
Instruction
Used To:
Page
COP - Copy File
Copy a range of data from one file
location to another
19-2
FLL - Fill File
Load a file with a program constant or a
value from an element address
19-3
BSL - Bit Shift Left
Load and unload data into a bit array one
bit at a time
19-5
BSR - Bit Shift Right
FFL - First In, First Out (FIFO) Load
FFU - First In, First Out (FIFO)
Unload
LFL - Last In, First Out (LIFO) Load
LFU - Last In, First Out (LIFO)
Unload
Load words into a file and unload them in
the same order (first in, first out)
Load words into a file and unload them in
reverse order (last in, first out)
19-7
19-9
19-12
19-15
19-18
19-1
MicroLogix 1500 Programmable Controllers User Manual
COP - Copy File
Instruction Type: output
Table 19-1: Execution Time for the COP Instruction
When Rung Is:
True
False
16 µs + 0.7 µs/word
0.00 µs
The COP instruction copies blocks of data from one location into another.
Table 19-2: COP Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Destination
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
• • • •
• • • •
• •
• •
•
•
•
Length
1. See Important note about indirect addressing.
Important:
You cannot use indirect addressing with: S, MG, PD, RTC, HSC,
PTO, PWM, STI, EII, BHI, MMI, DAT, TPI, CS0, and IOS files.
The source and destination file types must be the same except bit (B) and integer (N);
they can be interchanged. It is the address that determines the maximum length of the
block to be copied, as shown in the following table:
Table 19-3: Maximum Lengths for the COP Instruction
Source/Destination Data Type
1 word elements (ie. word)
2 word elements (ie. long word)
3 word elements (ie. counter)
19-2
Range of Length Operand
1 to 128
1 to 64
1 to 42
File Instructions
FLL - Fill File
Instruction Type: output
Table 19-4: Execution Time for the FLL Instruction
Data Size
word
long word
When Rung Is:
True
False
13+0.43 µs/word
0.00 µs
0.00 µs
13.7+0.859 µs/
dword
The FLL instruction loads elements of a file with either a constant or an address data
value for a given length. The following figure shows how file instruction data is
manipulated. The instruction fills the words of a file with a source value. It uses no
status bits. If you need an enable bit, program a parallel output that uses a storage
address.
Destination
Source
Word to File
19-3
MicroLogix 1500 Programmable Controllers User Manual
This instruction uses the following operands:
•
Source - The source operand is the address of the value or constant used to fill the
destination. The data range for the source is from -32768 to 32767 (word) or
-2,147,483,648 to 2,147,483,647 (long word).
Note: A constant cannot be used as the source in a timer (T), counter (C), or
control (R) file.
•
Destination - The starting destination address where the data is written.
•
Length - The length operand contains the number of elements. The length can
range from 1 to 128 (word), 1 to 64 (long word), or 1 to 42 (3 word element such
as counter).
Note:
The source and destination operands must be of the same file type, unless
they are bit (B) and integer (N).
Addressing Modes and File Types can be used as shown in the following table:
Table 19-5: FLL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
Destination
•
• •
•
• • • •
• • • •
Length
1. See Important note about indirect addressing.
19-4
Function Files
Address
Mode1
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• • •
• •
•
• • •
•
File Instructions
BSL - Bit Shift Left
Instruction Type: output
Table 19-6: Execution Time for the BSL Instruction
Data Size
word
long word
When Rung Is:
True
False
29+1.08 µs/word
0.00 µs
NA
NA
The BSL instruction loads data into a bit array on a false-to-true rung transition, one
bit at a time. The data is shifted left through the array, then unloaded, one bit at a time.
The following figure shows the operation of the BSR instruction.
Source Bit
I:22/12
Data block is shifted one bit at a time from
bit 16 to bit 73.
31 30 29 28 27 26 25 24 23
47 46 45 44 43 42 41 40 39
63 62 61 60 59 58 57 56 55
RESERVED
73 72 71
22
38
54
70
21
37
53
69
20
36
52
68
19
35
51
67
18
34
50
66
17
33
49
65
16
32
48
64
58 Bit Array #B3:1
Unload Bit
(R6:14/10)
If you wish to shift more than one bit per scan, you must create a loop in your
application using the JMP, LBL, and CTU instructions.
19-5
MicroLogix 1500 Programmable Controllers User Manual
This instruction uses the following operands:
•
File - The file operand is the address of the bit array that is to be manipulated.
•
Control - The control operand is the address of the BSL’s control element. The
control element consists of 3 words:
15 14 13 12 11 10 9
8
Word 0 EN1 -- DN2 -- ER3 UL4 not used
Word 1 Size of bit array (number of bits).
Word 2 not used
7
6
5
4
3
2
1
0
1. EN - Enable Bit is set on false-to-true transition of the rung and indicates the instruction is enabled.
2. DN - Done Bit, when set, indicates that the bit array has shifted one position.
3. ER - Error Bit, when set, indicates that the instruction detected an error such as entering a negative
number for the length or source operand.
4. UL - Unload Bit is the instruction’s output. Avoid using the UL (unload) bit when the ER (error) bit
is set.
•
Length - The length operand contains the length of the bit array in bits. The valid
data range for length is from 0 to 2048.
•
Source - The source is the address of the bit to be transferred into the bit array at
the first (lowest) bit position.
Addressing Modes and File Types can be used as shown in the following table:
Table 19-7: BSL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
File
Control
Length
Source
Function Files
•
•
•
• •
• •
•
1
•
• •
• • • •
1. Control file only. Not valid for Timers and Counters.
19-6
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
•
•
• • •
File Instructions
BSR - Bit Shift Right
Instruction Type: output
Table 19-8: Execution Time for the BSR Instruction
When Rung Is:
True
False
29+1.14 µs/word
0.00 µs
Unload Bit
(R6:15/10)
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
69
68
67
66
65
64
INVALID
38 Bit Array
#B3:2
Data block is shifted one bit at a time from
bit 69 to bit 32.
Source Bit
I:23/06
If you wish to shift more than one bit per scan, you must create a loop in your
application using the JMP, LBL, and CTU instructions.
19-7
MicroLogix 1500 Programmable Controllers User Manual
The BSR instruction loads data into a bit array on a false-to-true rung transition, one
bit at a time. The data is shifted right through the array, then unloaded, one bit at a
time. This instruction uses the following operands:
•
File - The file operand is the address of the bit array that is to be manipulated.
•
Control - The control operand is the address of the BSR’s control element. The
control element consists of 3 words:
15 14 13 12 11 10 9
8
Word 0 EN1 -- DN2 -- ER3 UL4 not used
Word 1 Size of bit array (number of bits).
Word 2 not used
7
6
5
4
3
2
1
0
1. EN - Enable Bit is set on false-to-true transition of the rung and indicates the instruction is enabled.
2. DN - Done Bit, when set, indicates that the bit array has shifted one position.
3. ER - Error Bit, when set, indicates that the instruction detected an error such as entering a negative
number for the length or source operand.
4. UL - Unload Bit is the instruction’s output. Avoid using the UL (unload) bit when the ER (error) bit
is set.
•
Length - The length operand contains the length of the bit array in bits. The data
range for length is from 0 to 2048.
•
Source - The source is the address of the bit to be transferred into the bit array at
the last (highest) bit position..
Addressing Modes and File Types can be used as shown in the following table:
Table 19-9: BSR Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
File
Control
Length
Source
Function Files
•
•
•
• •
• •
•
1
•
• •
• • • •
1. Control file only. Not valid for Timers and Counters.
19-8
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
•
•
• • •
File Instructions
FFL - First In, First Out (FIFO) Load
Instruction Type: output
Table 19-10: Execution Time for the FFL Instruction
Data Size
word
long word
When Rung Is:
True
False
20.00 µs
9.50 µs
23.00 µs
9.50 µs
On a false-to-true rung transition, the FFL instruction loads words or long words into
a user-created file called a FIFO stack. This instruction’s counterpart, FIFO unload
(FFU), is paired with a given FFL instruction to remove elements from the FIFO
stack. Instruction parameters have been programmed in the FFL - FFU instruction
pair shown below.
FFL
FIFO Load
Source
FIFO
Control
Length
Position
N7:10
#N7:12
R6:0
34
9
FFU
FIFO Unload
FIFO
#N7:12
Dest
N7:11
Control
R6:0
Length
34
Position
9
EN
Destination
DN
N7:11
N7:12
0
N7:13
1
FFU instruction unloads
data from stack #N7:12 at
position 0, N7:12
N7:14
2
EM
Position
3
4
EU
5
DN
6
34 words are allocated
for FIFO stack starting at
N7:12, ending at N7:45
7
EM
Source
8
N7:10
9
FFL instruction loads data
into stack #7:12 at the
next available position, 9
in this case.
N7:45
33
Loading and Unloading of Stack #N7:12
19-9
MicroLogix 1500 Programmable Controllers User Manual
This instruction uses the following operands:
•
Source - The source operand is a constant or address of the value used to fill the
currently available position in the FIFO stack. The address level of the source
must match the FIFO stack. If FIFO is a word size file, source must be a word
value or constant. If FIFO is a long word size file, source must be a long word
value or constant. The data range for the source is from -32768 to 32767 (word) or
-2,147,483,648 to 2,147,483,647 (long word).
•
FIFO - The FIFO operand is the starting address of the stack where the value in
source is loaded.
•
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
Word 0 EN1 -- DN2 EM3 not used
Word 1 Length - maximum number of words or long words in the stack.
Word 2 Position - the next available location where the instruction loads data.
2
1
0
1. EN - Enable Bit is set on false-to-true transition of the rung and indicates the instruction is enabled.
2. DN - Done Bit, when set, indicates that the stack is full.
3. EM - Empty Bit, when set, indicates FIFO is empty.
19-10
•
Length - The length operand contains the number of elements in the FIFO stack to
receive the value or constant found in the source. The length of the stack can range
from 1 to 128 (word) or 1 to 64 (long word). The position is incremented after
each load.
•
Position - This is the current location pointed to in the FIFO stack. It determines
the next location in the stack to receive the value or constant found in source.
Position is a component of the control register. The position can range from 0 to
128 (word) or 0 to 64 (long word).
File Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 19-11: FFL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
FIFO
Control
Function Files
Address
Mode
Address
Level
• • •
• •
•
• •
• •
•
•
•
•
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
• • • •
•
• •
1
Length
Position
•
1. Control file only. Not valid for Timers or Counters.
19-11
MicroLogix 1500 Programmable Controllers User Manual
FFU - First In, First Out (FIFO) Unload
Instruction Type: output
Table 19-12: Execution Time for the FFU Instruction
Data Size
word
long word
When Rung Is:
True
False
18+0.727 µs/word
9.50 µs
20+1.39 µs/word
9.50 µs
On a false-to-true rung transition, the FFU instruction unloads words or long words
from a user-created file called a FIFO stack. The data is unloaded using first-in, firstout order. After the unload completes, the data in the stack is shifted one element
toward the top of the stack and the last element is zeroed out. Instruction parameters
have been programmed in the FFL - FFU instruction pair shown below.
FFL
FIFO Load
Source
FIFO
Control
Length
Position
N7:10
#N7:12
R6:0
34
9
FFU
FIFO Unload
FIFO
#N7:12
Dest
N7:11
Control
R6:0
Length
34
Position
9
EN
Destination
DN
N7:11
EM
FFU instruction unloads
data from stack #N7:12 at
position 0, N7:12
Position
N7:12
0
N7:13
1
N7:14
2
3
4
EU
5
DN
6
34 words are allocated
for FIFO stack starting at
N7:12, ending at N7:45
7
EM
Source
8
N7:10
9
FFL instruction loads data
into stack #7:12 at the
next available position, 9
in this case.
N7:45
33
Loading and Unloading of Stack #N7:12
19-12
File Instructions
This instruction uses the following operands:
•
FIFO - The FIFO operand is the starting address of the stack.
•
Destination - The destination operand is a word or long word address that stores
the value which exits from the FIFO stack. The FFU instruction unloads this value
from the first location on the FIFO stack and places it in the destination address.
The address level of the destination must match the FIFO stack. If FIFO is a word
size file, destination must be a word size file. If FIFO is a long word size file,
destination must be a long word size file.
•
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
2
Word 0 -- EU1 DN2 EM3 not used
Word 1 Length - maximum number of words or long words in the stack.
Word 2 Position - the next available location where the instruction unloads data.
1
0
1. EU - Enable Unload Bit is set on false-to-true transition of the rung and indicates the instruction is
enabled.
2. DN - Done Bit, when set, indicates that the stack is full.
3. EM - Empty Bit, when set, indicates FIFO is empty.
•
Length - The length operand contains the number of elements in the FIFO stack.
The length of the stack can range from 1 to 128 (word) or 1 to 64 (long word).
•
Position - Position is a component of the control register. The position can range
from 0 to 128 (word) or 0 to 64 (long word). The position is decremented after
each unload. Data is unloaded at position zero.
19-13
MicroLogix 1500 Programmable Controllers User Manual
Addressing Modes and File Types can be used as shown in the following table:
Table 19-13: FFU Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
FIFO
Destination
Control
Function Files
• •
• •
•
• •
• • • •
• •
• •
•
1
Length
Position
1. Control file only. Not valid for Timers and Counters.
19-14
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
•
• •
• •
•
•
•
File Instructions
LFL - Last In, First Out (LIFO) Load
Instruction Type: output
Table 19-14: Execution Time for the LFL Instruction
Data Size
word
long word
When Rung Is:
True
False
20.00 µs
9.50 µs
24.00 µs
9.50 µs
On a false-to-true rung transition, the LFL instruction loads words or long words into
a user-created file called a LIFO stack. This instruction’s counterpart, LIFO unload
(LFU), is paired with a given LFL instruction to remove elements from the LIFO
stack. Instruction parameters have been programmed in the LFL - LFU instruction
pair shown below.
LFL
LIFO LOAD
Source
LIFO
Control
Length
Position
Destination
N7:10
#N7:12
R6:0
34
9
(EN)
(DN)
(EM)
Position
N7:11
N7:12
0
N7:13
1
LFU instruction unloads
data from stack #N7:12 at
position 8.
N7:14
2
3
4
LFU
LIFO UNLOAD
LIFO
Dest
Control
Length
Position
5
#N7:12
N7:11
R6:0
34
9
(EU)
(DN)
(EM)
6
34 words are allocated
for FIFO stack starting at
N7:12, ending at N7:45
7
Source
8
N7:10
9
LFL instruction loads data
into stack #N7:12 at the
next available position, 9
in this case.
N7:45
33
Loading and Unloading of Stack #N7:12
19-15
MicroLogix 1500 Programmable Controllers User Manual
The LFL instruction uses the following operands:
•
Source - The source operand is a constant or address of the value used to fill the
currently available position in the LIFO stack. The data size of the source must
match the LIFO stack. If LIFO is a word size file, source must be a word value or
constant. If LIFO is a long word size file, source must be a long word value or
constant. The data range for the source is from -32768 to 32767 (word) or
-2,147,483,648 to 2,147,483,647 (long word).
•
LIFO - The LIFO operand is the starting address of the stack where the value in
source is loaded.
•
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
Word 0 EN1 -- DN2 EM3 not used
Word 1 Length - maximum number of words or long words in the stack.
Word 2 Position - the next available location where the instruction loads data.
2
1
0
1. EN - Enable Bit is set on false-to-true transition of the rung and indicates the instruction is enabled.
2. DN - Done Bit, when set, indicates that the stack is full.
3. EM - Empty Bit, when set, indicates that LIFO is empty.
19-16
•
Length - The length operand contains the number of elements in the FIFO stack to
receive the value or constant found in the source. The length of the stack can range
from 1 to 128 (word) or 1 to 64 (long word). The position is incremented after
each load.
•
Position - This is the current location pointed to in the LIFO stack. It determines
the next location in the stack to receive the value or constant found in source.
Position is a component of the control register. The position can range from 0 to
128 (word) or 0 to 64 (long word).
File Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 19-15: LFL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Source
LIFO
Control
Function Files
Address
Mode
Address
Level
• • •
• •
•
• •
• •
•
•
•
•
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
• • • •
•
• •
1
Length
Position
•
1. Control file only. Not valid for Timers and Counters.
19-17
MicroLogix 1500 Programmable Controllers User Manual
LFU - Last In, First Out (LIFO) Unload
Instruction Type: output
Table 19-16: Execution Time for the LFU Instruction
Data Size
word
long word
When Rung Is:
True
False
20.80 µs
9.50 µs
24.00 µs
9.50 µs
On a false-to-true rung transition, the LFU instruction unloads words or long words
from a user-created file called a LIFO stack. The data is unloaded using last-in, firstout order. Instruction parameters have been programmed in the LFL - LFU instruction
pair shown below.
LFL
LIFO LOAD
Source
LIFO
Control
Length
Position
Destination
N7:10
#N7:12
R6:0
34
9
(EN)
(DN)
(EM)
N7:11
LFU instruction unloads
data from stack #N7:12 at
position 8.
Position
N7:12
0
N7:13
1
N7:14
2
3
4
LFU
LIFO UNLOAD
LIFO
Dest
Control
Length
Position
5
#N7:12
N7:11
R6:0
34
9
(EU)
(DN)
(EM)
6
34 words are allocated
for FIFO stack starting at
N7:12, ending at N7:45
7
Source
8
N7:10
9
LFL instruction loads data
into stack #N7:12 at the
next available position, 9
in this case.
N7:45
33
Loading and Unloading of Stack #N7:12
19-18
File Instructions
The LFU instruction uses the following operands:
•
LIFO - The LIFO operand is the starting address of the stack.
•
Destination - The destination operand is a word or long word address that stores
the value which exits from the LIFO stack. The LFU instruction unloads this value
from the last location on the LIFO stack and places it in the destination address.
The address level of the destination must match the LIFO stack. If LIFO is a word
size file, destination must be a word size file. If LIFO is a long word size file,
destination must be a long word size file.
•
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
2
Word 0 -- EU1 DN2 EM3 not used
Word 1 Length - maximum number of words or double words in the stack.
Word 2 Position - the next available location where the instruction unloads data.
1
0
1. EU - Enable Unload Bit is set on false-to-true transition of the rung and indicates the instruction is
enabled.
2. DN - Done Bit, when set, indicates that the stack is full.
3. EM - Empty Bit, when set, indicates LIFO is empty.
•
Length - The length operand contains the number of elements in the LIFO stack.
The length of the stack can range from 1 to 128 (word) or 1 to 64 (long word).
•
Position - This is the next location in the LIFO stack where data will be unloaded.
Position is a component of the control register. The position can range from 0 to
128 (word) or 0 to 64 (long word). The position is decremented after each unload.
Table 19-17: LFU Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
LIFO
Destination
Control
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
• •
• •
•
• •
• • • •
• •
• •
•
1
Length
Position
•
•
• •
• •
•
•
•
1. Control file only. Not valid for Timers and Counters.
19-19
MicroLogix 1500 Programmable Controllers User Manual
19-20
Sequencer Instructions
20
Sequencer Instructions
Sequencer instructions are used to control automatic assembly machines or processes
that have a consistent and repeatable operation. They are typically time based or event
driven.
Instruction
Used To:
Page
SQC - Sequencer Compare
Compare 16-bit data with stored data
20-2
SQO - Sequencer Output
Transfer 16-bit data to word addresses
20-6
SQL - Sequencer Load
Load 16-bit data into a file
20-10
Use the sequencer compare instruction to detect when a step is complete; use the
sequencer output instruction to set output conditions for each step. Use the sequencer
load instruction to load data into the sequencer file.
The primary advantage of sequencer instructions is to conserve program memory.
These instructions monitor and control 16 (word) or 32 (long word) discrete outputs
at a time in a single rung.
You can use bit integer or double integer files with sequencer instructions.
20-1
MicroLogix 1500 Programmable Controllers User Manual
SQC- Sequencer Compare
Instruction Type: output
Table 20-1: Execution Time for the SQC Instruction
Data Size
word
long word
When Rung Is:
True
False
21.30 µs
6.80 µs
22.80 µs
6.80 µs
On a false-to-true rung transition, the SQC instruction is used to compare masked
source words or long words with the masked value at a reference address (the
sequencer file) for the control of sequential machine operations.
When the status of all non-masked bits in the source word match those of the
corresponding reference word, the instruction sets the found bit (FD) in the control
word. Otherwise, the found bit (FD) is cleared.
The bits mask data when reset and pass data when set.
The mask can be fixed or variable. If you enter a hexadecimal code, it is fixed. If you
enter an element address or a file address for changing the mask with each step, it is
variable.
When the rung goes from false-to-true, the instruction increments to the next step
(word) in the sequencer file. Data stored there is transferred through a mask and
compared against the source for equality. While the rung remains true, the source is
compared against the reference data for every scan. If equal, the FD bit is set in the
SQCs control counter.
20-2
Sequencer Instructions
Applications of the SQC instruction include machine diagnostics. The following
figure explains how the SQC instruction works.
SQC
Sequencer Compare
File
#B11:10
Mask
FFF0
Source
I:3.0
Control
R6:21
Length
4
Position
2
EN
DN
FD
Input Word I:3.0
0010 0100 1001 1101
Mask Value FFF0
1111 1111 1111 0000
Sequencer Ref File #B10:11
Word
B10:11
12
13 0010 0100 1001 0000
14
15
Step
0
1
2
3
4
SQC FD bit is set when the instruction detects that an input word matches
(through mask) its corresponding reference word.
The FD bit R6:21/FD is set in the example, since the input word matches the
sequencer reference value using the mask value.
20-3
MicroLogix 1500 Programmable Controllers User Manual
This instruction uses the following operands:
•
File - This is the sequencer reference file. Its contents, on an element-by-element
basis are masked and compared to the masked value stored in source.
•
Mask - The mask operand contains the mask constant, word, or file which is
applied to both file and source. When mask bits are set to 1, data is allowed to pass
through for comparison. When mask bits are reset to 0, the data is masked (does
not pass through to for comparison). The immediate data ranges for mask are from
0 to 0xFFFF or 0 to 0xFFFFFFFF.
•
Source - This is the value that is compared to file.
Note:
•
If mask is direct or indirect, the position selects the location in the
specified file.
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
Word 0 EN1 -- DN2 -- ER3 not used FD4 not used
Word 1 Length - contains the number of steps in the sequencer reference file.
Word 2 Position - the current position in the sequence
2
1
0
1. EN - Enable Bit is set by a false-to-true rung transition and indicates that the instruction is enabled.
2. DN - Done Bit is set after the instruction has operated on the last word in the sequencer file. It is
reset on the next false-to-true rung transition after the rung goes false.
3. ER - Error Bit is set when the controller detects a negative position value, or a negative or zero
length value. When the ER bit is set, the minor error bit (S2:5/2) is also set.
4. FD - Found bit is set when the status of all non-masked bits in the source address match those of
the word in the sequencer reference file. This bit is assessed each time the SQC instruction is
evaluated while the rung is true.
•
Length - The length operand contains the number of steps in the sequencer file (as
well as Mask and/or Source if they are file data types). The length of the
sequencer can range from 1 to 255.
•
Position - This is the current location or step in the sequencer file (as well as Mask
and/or Source if they are file data types). It determines the next location in the
stack to receive the current comparison data. Position is a component of the
control register. The position can range from 0 to 255 for words and 0 to 127 for
long words. The position is incremented on each false-to-true transition.
Note:
20-4
If mask is direct or indirect, the position selects the location in the
specified file.
Sequencer Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 20 -2: SQC Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
File
Mask
Source
Control
Function Files
Address
Mode
Address
Level
• •
• • •
• •
•
• •
• •
• •
•
•
•
•
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• •
• •
•
•
•
•
• •
• •
• •
1
Length
Position
•
1. Control file only.
Note:
If file type is word, then mask and source must be words. If file type is
long word, mask and source must be long words.
20-5
MicroLogix 1500 Programmable Controllers User Manual
SQO- Sequencer Output
Instruction Type: output
Table 20-3: Execution Time for the SQO Instruction
Data Size
word
long word
When Rung Is:
True
False
20.20 µs
6.80 µs
23.40 µs
6.80 µs
On a false-to-true rung transition, the SQO instruction transfers masked source
reference words or long words to the destination, for the control of sequential
machine operations. When the rung goes from false-to-true, the instruction
increments to the next step (word) in the sequencer file. Data stored there is
transferred through a mask to the destination address specified in the instruction. Data
is written to the destination word every time the instruction is executed.
The done bit is set when the last word of the sequencer file is transferred. On the next
false-to-true rung transition, the instruction resets the position to step one.
If the position is equal to zero at start-up, when you switch the controller from the
program mode to the run mode instruction operation depends on whether the rung is
true or false on the first scan.
•
If true, the instruction transfers the value in step zero.
•
If false, the instruction waits for the first rung transition from false-to-true and
transfers the value in step one.
The bits mask data when reset and pass data when set. The instruction will not change
the value in the destination word unless you set mask bits.
The mask can be fixed or variable. It will be fixed if you enter a hexadecimal code. It
will be variable if you enter an element address or a file address for changing the
mask with each step.
The following figure indicates how the SQO instruction works.
20-6
Sequencer Instructions
SQO
Sequencer Output
File
#B10:1
Mask
0F0F
Dest
O14.0
Control
R6:20
Length
4
Position
2
Destination O:14.0
15
0000
8 7
0101
0
0000
1010
Mask Value 0F0F
15
87
0
0000 1111 0000 1111
Sequencer Output File #B10:1
Word
B10:1
2
3
4
5
0000
1010
1111
0101
0000
0000
0010
0101
0101
1111
0000
1111
0100
0101
0000
0000
0101
1010
0101
1111
Step
0
1
2
3
4
EN
DN
External Outputs
Associated with O:14
00
01
02
03
04
05
06
07
08
09
10
Current Step
11
12
13
14
15
ON
ON
ON
ON
20-7
MicroLogix 1500 Programmable Controllers User Manual
This instruction uses the following operands:
•
File - This is the sequencer reference file. Its contents, on an element-by-element
basis are masked and stored in the destination.
•
Mask - The mask operand contains the mask constant. When mask bits are set to
1, data is allowed to pass through to destination. When mask bits are reset to 0, the
data is masked (does not pass through to destination). The immediate data ranges
for mask are from 0 to 0xFFFF (word) or 0 to 0xFFFFFFFF (long word).
Note:
If mask is direct or indirect, the position selects the location in the
specified file.
•
Destination - The destination operand is the sequencer location or file.
•
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
Word 0 EN1 -- DN2 -- ER3 not used FD not used
Word 1 Length - contains the index of the last element in the sequencer reference file
Word 2 Position - the current position in the sequence
0
1. EN - Enable Bit is set by a false-to-true rung transition and indicates that the instruction is enabled.
2. DN - Done Bit is set after the instruction has operated on the last word in the sequencer file. It is
reset on the next false-to-true rung transition after the rung goes false.
3. ER - Error Bit is set when the controller detects a negative position value, or a negative or zero
length value. When the ER bit is set, the minor error bit (S2:5/2) is also set.
20-8
•
Length - The length operand contains the number of steps in the sequencer file (as
well as Mask and/or Destination if they are file data types). The length of the
sequencer can range from 1 to 255.
•
Position - This is the current location or step in the sequencer file (as well as Mask
and/or Destination if they are file data types). It determines the next location in the
stack to be masked and moved to the destination. Position is a component of the
control register. The position can range from 0 to 255. Position is incremented on
each false-to-true transition.
Sequencer Instructions
Addressing Modes and File Types can be used as shown in the following table:
Table 20 -4: SQO Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
File
Mask
Destination
Control
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Element
Bit
Word
Long Word
Data Files
•
• •
• •
•
•
•
•
• •
• •
• •
1
Length
Position
• •
• • •
• •
•
•
• •
• •
• •
•
•
•
•
1. Control file only.
Note:
If file type is word, then mask and source must be words. If file type is
long word, mask and source must be long words.
20-9
MicroLogix 1500 Programmable Controllers User Manual
SQL - Sequencer Load
Instruction Type: output
Table 20-5: Execution Time for the SQL Instruction
Data Size
word
long word
When Rung Is:
True
False
19.20 µs
6.80 µs
21.10 µs
6.80 µs
On a false-to-true rung transition, the SQL instruction loads words or long words into
a sequencer file at each step of a sequencer operation. This instruction uses the
following operands:
•
File - This is the sequencer reference file. Its contents are received on an elementby-element basis from the source.
•
Source - The source operand is a constant or address of the value used to fill the
currently available position sequencer file. The address level of the source must
match the sequencer file. If file is a word type, then source must be a word type. If
file is a long word type, then source must be a long word type. The data range for
the source is from -32768 to 32767 (word) or -2,147,483,648 to 2,147,483,647
(long word).
•
Control - This is a control file address. The status bits, stack length, and the
position value are stored in this element. The control element consists of 3 words:
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
Word 0 EN1 -- DN2 -- ER3 not used FD not used
Word 1 Length - contains the index of the last element in the sequencer reference file
Word 2 Position - the current position in the sequence
1. EN - Enable Bit is set by a false-to-true rung transition and indicates that the instruction is enabled.
2. DN - Done Bit is set after the instruction has operated on the last word in the sequencer file. It is
reset on the next false-to-true rung transition after the rung goes false.
3. ER - Error Bit is set when the controller detects a negative position value, or a negative or zero
length value. When the ER bit is set, the minor error bit (S2:5/2) is also set.
•
20-10
Length - The length operand contains the number of steps in the sequencer file
(this is also the length of source if it is a file data type). The length of the
sequencer can range from 1 to 255.
0
Sequencer Instructions
•
Position - This is the current location or step in the sequencer file (as well as
source if it is a file data type). It determines the next location in the stack to
receive the value or constant found in source. Position is a component of the
control register. The position can range from 0 to 255.
Table 20 -6: SQL Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
File
Source
Control
Function Files
Address
Mode
Address
Level
• •
• • •
•
• •
• •
•
•
•
•
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• •
•
•
•
• •
• •
1
Length
Position
•
1. Control file only.
Note:
If file type is word, then mask and source must be words. If file type is
long word, mask and source must be long words.
20-11
MicroLogix 1500 Programmable Controllers User Manual
20-12
Program Control Instructions
21
Program Control Instructions
Use these instructions to change the order in which the processor scans a ladder
program. Typically these instructions are used to minimize scan time, create a more
efficient program, and to troubleshoot a ladder program.
Instruction
JMP - Jump to Label
LBL - Label
JSR - Jump to Subroutine
SBR - Subroutine Label
Used To:
Page
Jump forward/backward to a
corresponding label instruction
21-2
Jump to a designated subroutine and
return
21-3
RET - Return from Subroutine
21-2
21-3
21-4
SUS - Suspend
Debug or diagnose your user program
21-4
TND - Temporary End
Abort current ladder scan
21-5
END - Program End
End a program or subroutine
21-5
MCR - Master Control Reset
Enable or inhibit a master control zone in
your ladder program
21-6
21-1
MicroLogix 1500 Programmable Controllers User Manual
JMP - Jump to Label
Instruction Type: output
Table 21-1: Execution Time for the JMP Instruction
When Rung Is:
True
False
0.39 µs
0.00 µs
The JMP instruction causes the controller to change the order of ladder execution.
Jumps cause program execution to go to the rung marked (LBL label number). Jumps
can be forward or backward in ladder logic within the same program file. Multiple
JMP instructions may cause execution to proceed to the same label.
The immediate data range for the label is from 0 to 999. The label is local to a
program file.
LBL - Label
Instruction Type: input
Table 21-2: Execution Time for the LBL Instruction
When Rung Is:
True
0.16 µs
False
0.16 µs
The LBL instruction is used in conjunction with a jump (JMP) instruction to change
the order of ladder execution. Jumps cause program execution to go to the rung
marked (LBL label number).
The immediate data range for the label is from 0 to 999. The label is local to a
program file.
21-2
Program Control Instructions
JSR - Jump to Subroutine
Instruction Type: output
Table 21-3: Execution Time for the JSR Instruction
When Rung Is:
True
False
6.43 µs
0.00 µs
The JSR instruction causes the controller to start executing a separate subroutine file
within a ladder program. JSR moves program execution to the designated subroutine
(SBR file number). After executing the SBR, control proceeds to the instruction
following the JSR instruction.
The immediate data range for the JSR file is from 3 to 255.
SBR - Subroutine Label
Instruction Type: input
Table 21-4: Execution Time for the SBR Instruction
When Rung Is:
True
0.16 µs
False
n/a
The SBR instruction is a label which is not used by the processor. It is for user
subroutine identification purposes as the first rung for that subroutine. This
instruction is the first instruction on a rung and is always evaluated as true.
21-3
MicroLogix 1500 Programmable Controllers User Manual
RET - Return from Subroutine
Instruction Type: output
Table 21-5: Execution Time for the RET Instruction
When Rung Is:
True
False
0.44 µs
0.00 µs
The RET instruction marks the end of subroutine execution or the end of the
subroutine file. It causes the controller to resume execution at the instruction
following the JSR instruction, user interrupt, or user fault routine that caused this
subroutine to execute.
SUS - Suspend
Instruction Type: output
Table 21-6: Execution Time for the SUS Instruction
When Rung Is:
True
0.66 µs
False
0.00 µs
The SUS instruction is used to trap and identify specific conditions for program
debugging and system troubleshooting. This instruction causes the processor to enter
the suspend idle mode causing all outputs to be de-energized. The suspend ID and the
suspend file (program file number or subroutine file number identifying where the
suspend instruction resides) are placed in the status file (S:7 and S:8).
The immediate data range for the suspend ID is from -32768 to 32767.
21-4
Program Control Instructions
TND - Temporary End
Instruction Type: output
The TND instruction is used to denote a premature end of ladder program execution.
The TND instruction cannot be executed from a STI subroutine, HSC subroutine, EII
subroutine, or a user fault subroutine. This instruction may appear more than once in a
ladder program.
On a true rung, TND stops the processor from scanning the rest of the program file. In
addition, this instruction performs the output scan, input scan, and housekeeping
aspects of the processor scan cycle prior to resuming scanning at rung 0 of the main
program (file 2). If this instruction is executed in a nested subroutine, it terminates
execution of all nested subroutines.
END - Program End
Instruction Type: output
Table 21-7: Execution Time for the END Instruction
When Rung Is:
True
0.33 µs
False
0.00 µs
The END instruction must appear at the end of every ladder program. For the main
program file (file 2), this instruction ends the program scan. For a subroutine,
interrupt, or user fault file, the END instruction causes a return from subroutine.
21-5
MicroLogix 1500 Programmable Controllers User Manual
MCR - Master Control Reset
Instruction Type: output
Table 21-8: Execution Time for the MCR Instructions
Instruction
MCR Start
MCR End
When Rung Is:
True
False
0.66 µs
0.66 µs
0.87 µs
0.87 µs
The MCR instruction works in pairs to control the ladder logic found between those
pairs. Rungs within the MCR zone are still scanned, but scan time is reduced due to
the false state of non-retentive outputs. Non-retentive outputs are reset when the rung
goes false.
I:1
] [
0
•
•
•
Ladder Logic
•
•
•
(MCR)
(MCR)
This instruction defines the boundaries of an MCR Zone. An MCR Zone is the set of
ladder logic instructions bounded by an MCR instruction pair. The start of an MCR
zone is defined to be the rung that contains an MCR instruction preceded by
conditional logic. The end of an MCR zone is defined to be the first rung containing
just an MCR instruction following a start MCR zone rung.
While the rung state of the first MCR instruction is true, execution shall proceed as if
the zone were not present. When the rung state of the first MCR instruction is false,
the ladder logic within the MCR zone is executed as if the rung is false. All nonretentive outputs within the MCR zone shall be reset.
MCR zones let you enable or inhibit segments of your program, such as for recipe
applications.
21-6
Program Control Instructions
When you program MCR instructions, note that:
•
You must end the zone with an unconditional MCR instruction.
•
You cannot nest one MCR zone within another.
•
Do not jump into an MCR zone. If the zone is false, jumping into it activates the
zone.
Note:
!
The MCR instruction is not a substitute for a hard-wired master control
relay that provides emergency stop capability. You still must install a
hard-wired master control relay to provide emergency I/O power
shutdown.
ATTENTION: If you start instructions such as timers or counters in
an MCR zone, instruction operation ceases when the zone is disabled.
Re-program critical operations outside the zone if necessary.
21-7
MicroLogix 1500 Programmable Controllers User Manual
21-8
Input and Output Instructions
22
Input and Output Instructions
The input and output instructions allow you to selectively update data without waiting
for the input and output scans.
Instruction
Used To:
Page
IIM - Immediate Input with Mask
Update data prior to the normal input
scan.
22-2
IOM - Immediate Output with Mask
Update outputs prior to the normal output
scan.
22-4
REF - I/O Refresh
Interrupt the program scan to execute the
I/O scan (write outputs, service
communications, read inputs)
22-6
22-1
MicroLogix 1500 Programmable Controllers User Manual
IIM - Immediate Input with Mask
Instruction Type: output
IIM
IIM
Immediate Input w/Mask
Slot
I:0.0
Mask
N7:0
Length
1
Note:
This instruction is used for the MicroLogix 1500 on-board I/O only. It is not
designed to be used with expansion I/O.
Table 22-1: Execution Time for the IIM Instruction
When Rung Is:
True
False
22.06 µs
0.00 µs
The IIM instruction allows you to selectively update input data without waiting for
the automatic input scan. This instruction uses the following operands:
•
Slot - This operand defines the location where data is obtained for updating the
input file. The location specifies the slot number and but the word where data is to
be obtained. For example, if slot = I:0, input data from slot 0 starting at word 0 is
masked and placed in input data file I:0 starting at word 0 for the specified length.
If slot = I0.1, word 1 of slot 0 is used, and so on.
Important:
•
Slot 0 is the only valid slot number that can be used with this
instruction. IIM cannot be used with expansion I/O.
Mask - The mask is a hex constant or register address containing the mask value
to be applied to the slot. If a given bit position in the mask is a “1”, the
corresponding bit data from slot is passed to the input data file. A “0” prohibits
corresponding bit data in slot from being passed to the input data file. The mask
value can range from 0 to 0xFFFF.
Bit
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Real Input
Input Word
Mask
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1
Input Data File
Data is Not Updated
Updated to Match Input Word
•
22-2
Length - This is the number of masked words to transfer to the input data file.
0
1
Input and Output Instructions
Addressing Modes and File Types can be used as shown below:
Table 22-2: IIM Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Slot
Mask
Length
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• •
• • •
•
• • •
•
•
22-3
MicroLogix 1500 Programmable Controllers User Manual
IOM - Immediate Output with Mask
Instruction Type: output
IIM
IOM
Immediate Output w/Mask
Slot
O:0.0
Mask
N7:0
Length
1
Note:
This instruction is used for the MicroLogix 1500 on-board I/O only. It is not
designed to be used with expansion I/O.
Table 22-3: Execution Time for the IOM Instruction
When Rung Is:
True
False
19.44 µs
0.00 µs
The IOM instruction allows you to selectively update output data without waiting for
the automatic output scan. This instruction uses the following operands:
•
Slot - The slot is the physical location that will be updated with data from the
output file.
Important:
•
Mask - The mask is a hex constant or register address containing the mask value
to be applied. If a given bit position in the mask is a “1”, the corresponding bit
data is passed to the physical outputs. A “0” prohibits corresponding bit data from
being passed to the outputs. The mask value can range from 0 to 0xFFFF.
Bit
Output Data
Mask
Real Outputs
•
22-4
Slot 0 is the only valid slot number that can be used with this
instruction. IOM cannot be used with expansion I/O.
15 14 13 12 11 10
0
9
8 7 6 5 4 3 2 1 0
Output Word
0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Data is Not Updated
Updated to Match Output Word
Length - This is the number of masked words to transfer to the outputs.
Input and Output Instructions
Addressing Modes and File Types can be used as shown below:
Table 22-4: IOM Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Slot
Mask
Length
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CS0 - Comms
IOS - I/O
Immediate
Direct
Indirect
Bit
Word
Long Word
Element
Data Files
•
• •
• • •
•
• • •
•
•
•
22-5
MicroLogix 1500 Programmable Controllers User Manual
REF- I/O Refresh
Instruction Type: output
Table 22-5: Execution Time for the REF Instruction
When Rung Is:
True
False
19.44 µs
0.00 µs
The REF instruction is used to interrupt the program scan to execute the I/O scan and
service communication portions of the operating cycle for all communication
channels. This includes: write outputs, service communications (all communication
channels, comms push-button, DAT, and comms housekeeping), and read inputs.
The REF instruction has no programming parameters. When it is evaluated as true,
the program scan is interrupted to execute the I/O scan and service communication
portions of the operating cycle. The scan then resumes at the instruction following the
REF instruction.
The REF instruction cannot be executed from an STI subroutine, HSC subroutine, EII
subroutine, or a user fault subroutine.
Note:
!
22-6
Using an REF instruction may result in input data changing in the
“middle” of a program scan. This condition needs to be evaluated when
using the REF instruction.
ATTENTION: The watchdog and scan timers are reset when
executing the REF instruction. You must insure that the REF
instruction is not placed inside a non-terminating program
loop. Do not place the REF instruction inside a program loop
unless the program is thoroughly analyzed.
Using Interrupts
23
Using Interrupts
Interrupts allow you to interrupt your program based on defined events. This chapter
contains information about using interrupts, the interrupt instructions, and the
interrupt function files. The chapter is arranged as follows:
•
“Information About Using Interrupts” on page 23-1.
•
“User Interrupt Instructions” on page 23-7.
•
“Using the Selectable Timed Interrupt (STI) Function File” on page 23-13.
•
“Using the Event Input Interrupt (EII) Function File” on page 23-19.
See also: “Using the High Speed Counter” on page 9-1.
Information About Using Interrupts
The purpose of this section is to explain some fundamental properties of the
Micrologix 1500 User Interrupts, including:
•
What is an interrupt?
•
When can the Micrologix 1500 operation be interrupted?
•
Priority of User Interrupts
•
Interrupt Latency
•
User Fault Routine
23-1
MicroLogix 1500 Programmable Controllers User Manual
What is an Interrupt?
An interrupt is an event that causes the processor to suspend the task it is currently
performing, perform a different task, and then return to the suspended task at the point
where it suspended. The Micrologix 1500 supports the following User Interrupts:
•
User Fault Routine
•
Event Interrupts (4)
•
High Speed Counter Interrupts (2)
•
Selectable Timed Interrupt
An interrupt must be configured and enabled to execute. When any one of the
interrupts is configured (and enabled) and subsequently occurs, the user program will:
1. suspend its execution
2. perform a defined task based upon which interrupt occurred
3. return to the suspended operation.
Interrupt Operation Example
Program File 2 is the main control program.
Program File 10 is the interrupt routine.
• An Interrupt Event occurs at rung 123.
• Program File 10 is executed.
• Program File 2 execution resumes
immediately after rung 123.
Program File 2
rung 0
Program File 10
rung 123
rung 275
Specifically, if the controller program is executing normally and an interrupt event
occurs:
1. the processor will stop its normal execution
2. determine which interrupt occurred
3. go immediately to rung 0 of the subroutine specified for that User Interrupt
4. begin executing until the end of that User Interrupt subroutine
(or set of subroutines if the specified subroutine calls a subsequent subroutine)
5. After completion of that subroutine, the processor resumes normal execution from
where it was interrupted.
23-2
Using Interrupts
When Can the Micrologix 1500 Operation be Interrupted?
The Micrologix 1500 only allows interrupts to be serviced during certain periods of a
program scan. They are:
•
At the start of a ladder rung
•
Anytime during End of Scan
•
Between data words in an expansion I/O scan
The interrupt will only be serviced by the processor at these opportunities. If the
interrupt is disabled, the pending bit will be set at the next occurrence of one of the
three listed occasions.
!
ATTENTION: If you enable interrupts during the program scan via
an OTL, OTE, or UIE, this instruction must be the last instruction
executed on the rung (last instruction on last branch). It is
recommended this be the only output instruction on the rung.
23-3
MicroLogix 1500 Programmable Controllers User Manual
Priority of User Interrupts
When multiple interrupts occur, the interrupts are serviced based upon their individual
priority.
When an interrupt occurs and another interrupt(s) has already occurred but has not
been serviced, the new interrupt will be scheduled for execution based on its priority
relative to the other pending interrupts. At the next point in time when an interrupt can
be serviced, all the interrupts will be executed in the sequence of highest priority to
lowest priority.
If an interrupt occurs while a lower priority interrupt is being serviced (executed), the
currently executing interrupt routine will be suspended, and the higher priority
interrupt will be serviced. Then the lower priority interrupt will be allowed to
complete before returning to normal processing.
If an interrupt occurs while a higher priority interrupt is being serviced (executed),
and the pending bit has been set for the lower priority interrupt, the currently
executing interrupt routine will continue to completion. Then the lower priority
interrupt will run before returning to normal processing.
The priorities from highest to lowest are:
User Fault Routine
highest priority
Event Interrupt 0
Event Interrupt 1
High Speed Counter Interrupt 0
Event Interrupt 2
•
•
•
Event Interrupt 3
High Speed Counter Interrupt 1
Selectable Timed Interrupt
23-4
lowest priority
Using Interrupts
Interrupt Latency
Interrupt Latency is defined as the worst case amount of time elapsed from when an
interrupt occurs to when the interrupt subroutine starts to execute. The tables below
show the interaction between an interrupt and the processor operating cycle.
Program Scan Activity
When an Interrupt can occur in MicroLogix 1500
Input Scan
Between word updates
Ladder Scan
Start of Rung
Output Scan
Between word updates
Communications Service
Anytime
Housekeeping
Anytime
To determine the interrupt latency:
1. First determine the execution time for the longest executing rung in your control
program (maximum rung time). See Appendix G for more information.
2. Multiply the maximum rung time by the Communications Multiplier corresponding to your configuration in the Scantime Worksheet on page F-8.
Evaluate you results as follows:
•
If the time calculated in step 2 is less than 100us, the interrupt latency is 360 µs.
•
If the time calculated in step 2 is greater than 100us, the user interrupt latency is
the sum of the time calculated in step 2 plus 260 µs.
23-5
MicroLogix 1500 Programmable Controllers User Manual
User Fault Routine
The user fault routine gives you the option of preventing a processor shutdown when a
specific user fault occurs. The fault routine is executed when any recoverable or nonrecoverable user fault occurs. The fault routine is not executed for non-user faults.
Faults are classified as recoverable, non-recoverable, and non-user faults. A complete
list of faults for the MicroLogix 1500 controllers appear in “Troubleshooting Your
System” on page C-1. The basic types of faults are described below:
Recoverable
Non-Recoverable
Non-User Fault
Recoverable Faults are caused by the
user and are recovered from by executing
the user fault routine. The user fault
routine recovers by clearing the Major
Error Halted bit, S:1/13.
Note: You may initiate a MSG instruction
to another device to identify the fault
condition of the processor.
Non-Recoverable Faults are caused by
the user, and cannot be recovered from.
The user fault routine executes when this
type of fault occurs. However, the fault
cannot be cleared.
Note: You may initiate a MSG instruction
to another device to identify the fault
condition of the controller.
Non-User Faults are caused by various
conditions that cease ladder program
execution. The user fault routine does not
execute when this type of fault occurs.
Status File Data Saved
The Arithmetic Flags (Status File word S:0) are saved on entry to the user fault
subroutine and re-written upon exiting the subroutine.
Creating a User Fault Subroutine
To use the user fault subroutine:
1. Create a subroutine file. Program Files 3 to 255 can be used
2. Enter the file number in word S:29 of the status file.
MicroLogix 1500 Processor Operation
The occurrence of recoverable or non-recoverable faults causes the processor to read
S:29 and execute the subroutine number identified by S:29. If the fault is recoverable,
the routine can be used to correct the problem and clear the fault bit S:1/13. The
processor then continues in its current executing mode. The routine does not execute
for non-user faults.
23-6
Using Interrupts
User Interrupt Instructions
Instruction
INT - Interrupt Subroutine
Used To:
Use this instruction to identify a program file as an
interrupt subroutine (INT label) versus a regular
subroutine (SBR label). This should be the first
instruction in your interrupt subroutine.
Page
23-7
STS - Selectable Timed Start Use the STS (Selectable Timed Interrupt Start)
instruction to the start the STI timer from the control
program, rather than starting automatically.
23-8
UID - User Interrupt Disable
23-9
UIE - User Interrupt Enable
UIF - User Interrupt Flush
Use the User Interrupt Disable (UID) and the User
Interrupt Enable (UIE) instructions to create zones in
which I/O interrupts cannot occur.
Use the UIF instruction to remove selected pending
interrupts from the system.
23-10
23-12
INT - Interrupt Subroutine
Instruction Type: input
INT
INT
I/O Interrupt
Table 23-1: Execution Time for the INT Instruction
When Rung Is:
True
0.16 µs
False
n/a
The INT instruction is used as a label to identify a user interrupt service routine (ISR).
This instruction is placed as the first instruction on a rung, and is always evaluated as
true. Use of the INT instruction is optional.
23-7
MicroLogix 1500 Programmable Controllers User Manual
STS - Selectable Timed Start
Instruction Type: output
STS
STS
Selectable Timed Start
Time
1
Table 23-2: Execution Time for the STS Instruction
When Rung Is:
True
False
62.73 µs
0.00 µs
The STS instruction can be used to start and stop the STI function or to change the
time interval between STI user interrupts. The STI instruction has one operand:
•
Time - This is the amount of time (in milliseconds) which must expire prior to
executing the selectable timed user interrupt. A value of zero disables the STI
function. The time range is from 0 to 65,535 milliseconds.
The STS instruction applies the specified set point to the STI function as follows:
•
If a zero set point is specified, the STI is disabled and STI:0/TIE is cleared (0).
•
If the STI is disabled (not timing) and a value greater than 0 is entered into the set
point, the STI starts timing to the new set point and STI:0/TIE is set (1).
•
If the STI is currently timing and the set point is changed, the new setting takes
effect immediately and the STI continues to time until it reaches the new set point.
Note that if the new setting is less than the current accumulated time, the STI
times-out immediately. For example, if the STI has been timing for 15
microseconds, and the STI set point is changed from 20 microseconds to 10
microseconds, an STI user interrupt occurs at the next start-of-rung.
Addressing Modes and File Types can be used as shown below:
Table 23-3: STS Instruction Valid Addressing Modes and File Types
For definitions of the terms used in this table see “Using the Instruction Descriptions” on page 11-2.
Parameter
Time
23-8
Function Files
Address
Mode
Address
Level
O
I
S
B
T, C, R
N
L
MG, PD
RTC
HSC
PTO, PWM
STI
EII
BHI
MMI
DAT
TPI
CSF - Comms
IOS - I/O
Immediate
Direct
Indirect
Element
Bit
Word
Long Word
Data Files
•
•
• • •
• • •
•
Using Interrupts
UID - User Interrupt Disable
Instruction Type: output
UID
UID
User Interrupt Disable
Interrupt Types
5
Table 23-4: Execution Time for the UID Instruction
When Rung Is:
True
False
0.59 µs
0.00 µs
The UID instruction is used to disable selected user interrupts. The table below shows
the types of interrupts with their corresponding disable bits:
Table 23-5: Types of Interrupts Disabled by the UID Instruction
Interrupt
EII - Event Input Interrupts
EII - Event Input Interrupts
HSC - High Speed Counter
EII - Event Input Interrupts
EII - Event Input Interrupts
HSC - High Speed Counter
STI - Selectable Timed Interrupts
Note: Bits 7 to 15 must be set to zero.
Element
Event 0
Event 1
HSC0
Event 2
Event 3
HSC1
STI
Decimal Value
64
32
16
8
4
2
1
Corresponding Bit
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
To disable interrupt(s):
1. Select which interrupts you want to disable.
2. Find the Decimal Value for the interrupt(s) you selected.
3. Add the Decimal Values if you selected more than one type of interrupt.
4. Enter the sum into the UID instruction.
For example, to disable EII Event 1 and EII Event 3:
EII Event 1 = 32, EII Event 3 = 4
32 + 4 = 36 (enter this value)
23-9
MicroLogix 1500 Programmable Controllers User Manual
UIE - User Interrupt Enable
Instruction Type: output
UID
UIE
User Interrupt Enable
Interrupt Types
4
Table 23-6: Execution Time for the UIE Instruction
When Rung Is:
True
False
0.66 µs
0.00 µs
The UIE instruction is used to enable selected user interrupts. The table below shows
the types of interrupts with their corresponding enable bits:
Table 23-7: Types of Interrupts Enabled by the UIE Instruction
Interrupt
EII - Event Input Interrupts
EII - Event Input Interrupts
HSC - High Speed Counter
EII - Event Input Interrupts
EII - Event Input Interrupts
HSC - High Speed Counter
STI - Selectable Timed Interrupts
Note: Bits 7 to 15 must be set to zero.
23-10
Element
Event 0
Event 1
HSC0
Event 2
Event 3
HSC1
STI
Decimal Value
64
32
16
8
4
2
1
Corresponding Bit
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Using Interrupts
To enable interrupt(s):
1. Select which interrupts you want to enable.
2. Find the Decimal Value for the interrupt(s) you selected.
3. Add the Decimal Values if you selected more than one type of interrupt.
4. Enter the sum into the UIE instruction.
For example, to enable EII Event 1 and EII Event 3:
EII Event 1 = 32, EII Event 3 = 4
32 + 4 = 36 (enter this value)
!
ATTENTION: If you enable interrupts during the program scan via
an OTL, OTE, or UIE, this instruction must be the last instruction
executed on the rung (last instruction on last branch). It is recommended
this be the only output instruction on the rung.
23-11
MicroLogix 1500 Programmable Controllers User Manual
UIF - User Interrupt Flush
Instruction Type: output
UID
UIF
User Interrupt Flush
Interrupt Types
1
Table 23-8: Execution Time for the UIF Instruction
When Rung Is:
True
False
9.79 µs
0.00 µs
The UIF instruction is used to flush (remove pending interrupts from the system)
selected user interrupts. The table below shows the types of interrupts with their
corresponding flush bits:
Table 23-9: Types of Interrupts Disabled by the UID Instruction
Interrupt
EII - Event Input Interrupts
EII - Event Input Interrupts
HSC - High Speed Counter
EII - Event Input Interrupts
EII - Event Input Interrupts
HSC - High Speed Counter
STI - Selectable Timed Interrupts
Note: Bits 7 to 15 must be set to zero.
Element
Event 0
Event 1
HSC0
Event 2
Event 3
HSC1
STI
Decimal Value
64
32
16
8
4
2
1
Corresponding Bit
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
To flush interrupt(s):
1. Select which interrupts you want to flush.
2. Find the Decimal Value for the interrupt(s) you selected.
3. Add the Decimal Values if you selected more than one type of interrupt.
4. Enter the sum into the UIF instruction.
For example, to disable EII Event 1 and EII Event 3:
EII Event 1 = 32, EII Event 3 = 4
32 + 4 = 36 (enter this value)
23-12
Using Interrupts
Using the Selectable Timed Interrupt (STI) Function File
The Selectable Timed Interrupt (STI) within the MicroLogix 1500 controller provides
a mechanism to solve time critical control requirements. The STI is a trigger
mechanism that allows you to scan or solve control program logic that is time
sensitive.
Example of where you would use the STI are:
•
PID type applications, where a calculation must be performed at a specific time
interval.
•
A motion application, where the motion instruction (PTO) needs to be scanned at
a specific rate to guarantee a consistent acceleration/deceleration profile.
•
A block of logic that needs to be scanned more often.
How an STI is used is typically driven by the demands/requirements of the
application. It operates using the following sequence:
1. The user selects a time interval.
2. When a valid interval is set and the STI is properly configured, the controller monitors the STI value.
3. When the time period has elapsed, the controller’s normal operation is interrupted.
4. The controller then scans the logic in the STI program file.
5. When the STI file scan is completed, the controller returns to where it was prior to
the interrupt, and continues normal operation.
23-13
MicroLogix 1500 Programmable Controllers User Manual
Selectable Time Interrupt (STI) Function File Sub-Elements Summary
Table 23-10: Selectable Timed Interrupt Function File (STI:0)
Sub-Element Description
PFN - Program File Number
ER - Error Code
UIX - User Interrupt Executing
UIE - User Interrupt Enable
UIL - User Interrupt Lost
UIP - User Interrupt Pending
TIE - Timed Interrupt Enabled
AS - Auto Start
ED - Error Detected
SPM - Set Point Msec
23-14
Address
STI:0.PFN
STI:0.ER
STI:0/UIX
STI:0/UIE
STI:0/UIL
STI:0/UIP
STI:0/TIE
STI:0/AS
STI:0/ED
STI:0.SPM
Data Format
word (INT)
word (INT)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
word (INT)
Type
control
status
status
control
status
status
control
control
status
control
User Program
Access
read only
read only
read only
read/write
read/write
read only
read/write
read only
read only
read/write
For More
Information
23-15
23-15
23-16
23-16
23-16
23-17
23-17
23-17
23-18
23-18
Using Interrupts
STI Function File Sub-Elements
STI Program File Number (PFN)
Sub-Element Description
PFN - Program File Number
Address
STI:0.PFN
Data Format
word (INT)
Type
control
User Program
Access
read only
The PFN (Program File Number) variable defines which subroutine is called
(executed) when the timed interrupt times out. A valid subroutine file is any program
file (3 to 255).
The subroutine file identified in the PFN variable is not a special file within the
controller, it is programmed and operates the same as any other program file. From
the control program perspective it is unique, in that it is automatically scanned based
on the STI set point.
STI Error Code (ER)
Sub-Element Description
ER - Error Code
Address
STI:0.ER
Data Format
word (INT)
Type
status
User Program
Access
read only
Error codes detected by the STI sub-system are displayed in this register. The table
below explains the error codes.
Table 23-11: STI Error Code
Error
Code
1
Recoverable Fault
(Controller)
Invalid Program File
Description
Program file number is less than 3, greater than 255, or does not
exist
23-15
MicroLogix 1500 Programmable Controllers User Manual
STI User Interrupt Executing (UIX)
Sub-Element Description
UIX - User Interrupt Executing
Address
STI:0/UIX
Data Format
binary (bit)
Type
status
User Program
Access
read only
The UIX (User Interrupt Executing) bit is set whenever the STI mechanism completes
timing and the controller is scanning the STI PFN. The UIX bit is cleared when the
controller completes processing the STI subroutine.
The STI UIX bit can be used in the control program as conditional logic to detect if an
STI interrupt is executing.
STI User Interrupt Enable (UIE)
Sub-Element Description
UIE - User Interrupt Enable
Address
STI:0/UIE
Data Format
binary (bit)
Type
control
User Program
Access
read/write
The UIE (User Interrupt Enable) bit is used to enable or disable STI subroutine
processing. This bit must be set if the user wants the controller to process the STI
subroutine at the configured time interval.
STI User Interrupt Lost (UIL)
Sub-Element Description
UIL - User Interrupt Lost
Address
STI:0/UIL
Data Format
binary (bit)
Type
status
User Program
Access
read/write
The UIL (User Interrupt Lost) is a status flag that represents an interrupt has been
lost. The MicroLogix 1500 can process 1 active, and maintain up to 2 pending user
interrupt conditions.
This bit is set by the MicroLogix 1500. It is up to the control program to utilize, track
if necessary, and clear the lost condition.
23-16
Using Interrupts
STI User Interrupt Pending (UIP)
Sub-Element Description
UIP - User Interrupt Pending
Address
STI:0/UIP
Data Format
binary (bit)
Type
status
User Program
Access
read only
The UIP (User Interrupt Pending) is a status flag that represents an interrupt is
pending. This status bit can be monitored, or used for logic purposes in the control
program if you need to determine when a subroutine cannot execute immediately.
This bit is controlled by the MicroLogix 1500, and is set and cleared automatically.
STI Timed Interrupt Enabled (TIE)
Sub-Element Description
TIE - Timed Interrupt Enabled
Address
STI:0/TIE
Data Format
binary (bit)
Type
control
User Program
Access
read/write
The TIE (Timed Interrupt Enabled) control bit is used to enable or disable the timed
interrupt mechanism. When set (1), timing is enabled, when clear (0) timing is
disabled. If this bit is cleared (disabled) while the timer is running, the accumulated
value is cleared (0). If the bit is then set (1), timing will start.
This bit is controlled by the user program, and retains its value through a power cycle.
STI Auto Start (AS)
Sub-Element Description
AS - Auto Start
Address
STI:0/AS
Data Format
binary (bit)
Type
control
User Program
Access
read only
The AS (Auto Start) is a control bit that can be used in the control program. The auto
start bit is configured with the programming device, and stored as part of the user
program. The auto start bit defines if the STI function automatically starts whenever
the MicroLogix 1500 controller enters any executing mode.
23-17
MicroLogix 1500 Programmable Controllers User Manual
STI Error Detected (ED)
Sub-Element Description
ED - Error Detected
Address
STI:0/ED
Data Format
binary (bit)
Type
status
User Program
Access
read only
The ED (Error Detected) flag is a status bit that can be used by the control program to
detect if an error is present in the STI sub-system. The most common type of error
that this bit represents is a configuration error. When this bit is set the user should
look at the error code in parameter STI:0.ER
This bit is controlled by the MicroLogix 1500, and is set and cleared automatically.
STI Set Point Milliseconds Between Interrupts (SPM)
Sub-Element
Description
SPM - Set Point Msec
Address
STI:0.SPM
Data Format
word (INT)
Range
Type
0 to 65,535
control
User Program
Access
read/write
When the controller transitions to an executing mode, the SPM (set point in
milliseconds) value is loaded into the STI. If the STI is configured correctly, and
enabled, the program file identified in the STI variable PFN is scanned at this interval.
This value can be changed from the control program by using the STS instruction.
Note:
23-18
The minimum value cannot be less than the time required to scan the STI
program file (STI:0.PFN) plus the Interrupt Latency.
Using Interrupts
Using the Event Input Interrupt (EII) Function File
The EII (event input interrupt) is a feature that allows the user to scan a specific
program file (subroutine), when an input condition is detected from a field device.
Within the function file section of RSLogix 500, the user sees an EII folder. Within
the folder are four EII elements. Each of these elements (EII:0, EII:1, EII:2, and
EII:3) are identical, this explanation uses EII:0.
Each EII can be configured to monitor any one of the first eight (inputs I1:0.0/0 to
I1:0.0/7). Each EII can be configured to detect rising edge or falling edge input
signals. When the configured input signal is detected at the input terminal, the
controller immediately scans the configured subroutine.
23-19
MicroLogix 1500 Programmable Controllers User Manual
Event Input Interrupt (EII) Function File Sub-Elements Summary
Table 23-12: Event Input Interrupt Function File (EII:0)
Sub-Element Description
PFN - Program File Number
ER - Error Code
UIX - User Interrupt Executing
UIE - User Interrupt Enable
UIL - User Interrupt Lost
UIP - User Interrupt Pending
EIE - Event Interrupt Enabled
AS - Auto Start
ED - Error Detected
ES - Edge Select
IS - Input Select
23-20
Address
EII:0.PFN
EII0.ER
EII0/UIX
EII0/UIE
EII0/UIL
EII:0/UIP
EII:0/EIE
EII:0/AS
EII:0/ED
EII:0/ES
EII:0.IS
Data Format
word (INT)
word (INT)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
word (INT)
Type
control
status
status
control
status
status
control
control
status
control
control
User Program
Access
read only
read only
read only
read/write
read/write
read only
read/write
read only
read only
read only
read only
For More
Information
23-21
23-21
23-22
23-22
23-22
23-23
23-23
23-23
23-24
23-24
23-24
Using Interrupts
EII Function File Sub-Elements
EII Program File Number (PFN)
Sub-Element Description
PFN - Program File Number
Address
EII:0.PFN
Data Format
word (INT)
Type
control
User Program
Access
read only
PFN (Program File Number) defines which subroutine is called (executed) when the
input terminal assigned to EII:0 detects a signal. A valid subroutine file is any
program file (3 to 255).
The subroutine file identified in the PFN variable is not a special file within the
controller. It is programmed and operates the same as any other program file. From
the control program perspective it is unique, in that it is automatically scanned based
on the configuration of the EII.
EII Error Code (ER)
Sub-Element Description
ER - Error Code
Address
EII0.ER
Data Format
word (INT)
Type
status
User Program
Access
read only
ERs (Error Codes) detected by the EII sub-system are displayed in this register. The
table below explains the error codes.
Table 23-13: EII Error Codes
Error
Code
1
2
3
Recoverable Fault
(Controller)
Invalid Program File
Invalid Input
Input Overlap
Description
Program file number is less than 3, greater than 255, or does not
exist
Valid numbers must be 0, 1, 2, 3, 4, 5, 6, or 7
EIIs cannot share inputs. Each EII must have a unique input.
23-21
MicroLogix 1500 Programmable Controllers User Manual
EII User Interrupt Executing (UIX)
Sub-Element Description
UIX - User Interrupt Executing
Address
EII0/UIX
Data Format
binary (bit)
Type
status
User Program
Access
read only
The UIX (User Interrupt Executing) bit is set whenever the EII mechanism detects a
valid input and the controller is scanning the PFN. The EII mechanism clears the UIX
bit when the controller completes its processing of the EII subroutine.
The EII UIX bit can be used in the control program as conditional logic to detect if an
EII interrupt is executing.
EII User Interrupt Enable (UIE)
Sub-Element Description
UIE - User Interrupt Enable
Address
EII0/UIE
Data Format
binary (bit)
Type
control
User Program
Access
read/write
The UIE (User Interrupt Enable) bit is used to enable or disable EII subroutine
processing. This bit must be set if the user wants the controller to process the EII
subroutine when EII event occurs.
EII User Interrupt Lost (UIL)
Sub-Element Description
UIL - User Interrupt Lost
Address
EII0/UIL
Data Format
binary (bit)
Type
status
User Program
Access
read/write
UIL (User Interrupt Lost) is a status flag that represents an interrupt has been lost.
The MicroLogix 1500 can process 1 active, and maintain up to 2 pending user
interrupt conditions.
This bit is set by the MicroLogix 1500. It is up to the control program to utilize, track,
and clear the lost condition.
23-22
Using Interrupts
EII User Interrupt Pending (UIP)
Sub-Element Description
UIP - User Interrupt Pending
Address
EII:0/UIP
Data Format
binary (bit)
Type
status
User Program
Access
read only
UIP (User Interrupt Pending) is a status flag that represents an interrupt is pending.
This status bit can be monitored, or used for logic purposes, in the control program if
you need to determine when a subroutine cannot execute immediately.
This bit is controlled by the MicroLogix 1500, and is set and cleared automatically.
EII Event Interrupt Enable (EIE)
Sub-Element Description
EIE - Event Interrupt Enabled
Address
EII:0/EIE
Data Format
binary (bit)
Type
control
User Program
Access
read/write
EIE (Event Interrupt Enabled) allows the event interrupt function to be enabled or
disabled from the control program. When set (1), the function is enabled, when
cleared (0, default) the function is disabled.
This bit is controlled by the user program, and retains its value through a power cycle.
EII Auto Start (AS)
Sub-Element Description
AS - Auto Start
Address
EII:0/AS
Data Format
binary (bit)
Type
control
User Program
Access
read only
AS (Auto Start) is a control bit that can be used in the control program. The auto start
bit is configured with the programming device, and stored as part of the user program.
The auto start bit defines if the EII function automatically starts whenever the
MicroLogix 1500 controller enters any executing mode.
23-23
MicroLogix 1500 Programmable Controllers User Manual
EII Error Detected (ED)
Sub-Element Description
ED - Error Detected
Address
EII:0/ED
Data Format
binary (bit)
Type
status
User Program
Access
read only
The ED (Error Detected) flag is a status bit that can be used by the control program to
detect if an error is present in the EII sub-system. The most common type of error that
this bit represents is a configuration error. When this bit is set the user should look at
the specific error code in parameter EII:0.ER
This bit is controlled by the MicroLogix 1500, and is set and cleared automatically.
EII Edge Select (ES)
Sub-Element Description
ES - Edge Select
Address
EII:0/ES
Data Format
binary (bit)
Type
control
User Program
Access
read only
The ES (Edge Select) bit selects the type of trigger that causes an Event Interrupt.
This bit allows the EII to be configured for rising edge (off-to-on, 0-to-1), or falling
edge (on-to-off, 1-to-0) signal detection. This selection is based on the type of field
device that is connected to the controller.
The default condition is 1, which configures the EII for rising edge operation.
EII Input Select (IS)
Sub-Element Description
IS - Input Select
Address
EII:0.IS
Data Format
word (INT)
Type
control
User Program
Access
read only
The IS (Input Select) parameter is used to configure each EII to a specific input on the
controller. Valid inputs are 0 to 7, which correspond to I1:0.0/0 to I1:0.0/7.
This parameter is configured with the programming device and cannot be changed
from the control program.
23-24
Process Control Instruction
24
Process Control Instruction
This chapter describes the MicroLogix 1500 Proportional Integral Derivative (PID)
instruction. The PID instruction is an output instruction that controls physical
properties such as temperature, pressure, liquid level, or flow rate using process loops.
The PID Concept
The PID instruction normally controls a closed loop using inputs from an analog input
module and providing an output to an analog output module. For temperature control,
you can convert the analog output to a time proportioning on/off output for driving a
heater or cooling unit. An example appears on page 24-21.
The PID instruction can be operated in the timed mode or the Selectable Time
Interrupt (STI mode). In the timed mode, the instruction updates its output
periodically at a user-selectable rate. In the STI mode, the instruction should be
placed in an STI interrupt subroutine. It then updates its output every time the STI
subroutine is scanned. The STI time interval and the PID loop update rate must be the
same in order for the equation to execute properly. See “Using the Selectable Timed
Interrupt (STI) Function File” on page 23-13 for more information on STI interrupts.
PID closed loop control holds a process variable at a desired set point. A flow rate/
fluid level example is shown below.
Feed Forward
or Bias
Set Point
Error
Flow Rate
PID
Equation
Process
Variable
Control
Output
Level
Detector
Control Valve
24-1
MicroLogix 1500 Programmable Controllers User Manual
The PID equation controls the process by sending an output signal to the control
valve. The greater the error between the setpoint and process variable input, the
greater the output signal. Alternately, the smaller the error, the smaller the output
signal. An additional value (feed forward or bias) can be added to the control output
as an offset. The PID result (control variable) drives the process variable toward the
set point.
The PID Equation
The PID instruction uses the following algorithm:
Standard equation with dependent gains:
1
D ( PV )
Output = K C ( E ) + ----- ∫ ( E ) dt + T D ⋅ ----------------- + bias
TI
df
Standard Gains constants are:
Term
Range (Low to High)
Reference
Controller Gain KC
0.01 to 327.67 (dimensionless)①
Proportional
Reset Term 1/TI
327.67 to 0.01 (minutes per repeat)①
Integral
Rate Term TD
0.01 to 327.67 (minutes)①
Derivative
①
Applies to MicroLogix 1500 PID range when Reset and Gain Range (RG) bit is set to 1. For more
information on reset and gain, see “PLC 5 Gain Range (RG)” on page 24-15.
The derivative term (rate) provides smoothing by means of a low-pass filter. The cutoff frequency of the filter is 16 times greater than the corner frequency of the
derivative term.
24-2
Process Control Instruction
PD Data File
The PID instruction implemented by the MicroLogix 1500 is virtually identical in
function to the PID implementation used by the Allen-Bradley SLC 5/03 and higher
processors. Minor differences primarily involve enhancements to terminology. The
major difference is that the PID instruction now has its own data file. In the SLC
family of processors, the PID instruction operated as a block of registers within an
integer file. The Micrologix 1500 PID instruction utilizes a PD data file.
You can create a PD data file by creating a new data file and classifying it as a PD file
type. RSLogix automatically creates a new PD file or a PD sub-element whenever a
PID instruction is programmed on a rung.
Each PD data file has a maximum of 255 elements, and each PID instruction requires
a unique PD element. Each PD element is composed of 20 sub-elements, which
include bit, integer and long integer data. All of the examples in this chapter use PD
file 10 sub-element 0.
24-3
MicroLogix 1500 Programmable Controllers User Manual
PID Instruction
Normally, you place the PID instruction on a rung without conditional logic. If
conditional logic is in front of the PID instruction, the output remains at its last value
when the rung is false. The integral term is also cleared when the rung is false.
Note:
In order to stop and restart the PID instruction, you need to create a
false-to-true rung transition.
The example below shows a PID instruction on a rung with RSLogix 500
programming software.
When programming, the setup screen provides access to the PID instruction
configuration parameters. The illustration shows the RSLogix 500 setup screen.
24-4
Process Control Instruction
Input Parameters
The table below shows the input parameter addresses, data formats, and types of user
program access. See the indicated pages for descriptions of each parameter.
Input Parameter Descriptions
Address
Data
Format
Range
Type
User Program
Access
For More
Information
SPV - Scaled Process Variable
PD10:0.SPV
word (INT)
0 to 16383
status
read only
24-5
MAXS - Setpoint Maximum
PD10:0.MAXS
word (INT)
-32,768 to +32,767
control
read/write
24-5
MINS - Setpoint Minimum
PD10:0.MINS
word (INT)
-32,768 to +32,767
control
read/write
24-6
OSP - Old Setpoint Value
PD10:0.OSP
word (INT)
-32,768 to +32,767
status
read only
24-6
Scaled Process Variable (SPV)
Input Parameter Descriptions
Address
SPV - Scaled Process Variable
PD10:0.SPV
Data
Format
Range
Type
User Program
Access
word (INT)
0 to 16383
status
read only
The SPV (Scaled Process Variable) is the analog input variable. If scaling is enabled,
the range is the minimum scaled value (MinS) to maximum scaled value (MaxS).
If the SPV is configured to be read in engineering units, then this parameter
corresponds to the value of the process variable in engineering units. See “Analog I/O
Scaling” on page 24-21 for more information on scaling.
Setpoint MAX (MAXS)
Input Parameter Descriptions
MAXS - Setpoint Maximum
Address
Data
Format
Range
Type
User Program
Access
PD10:0.MAXS
word (INT)
-32,768 to +32,767
control
read/write
If the SPV is read in engineering units, then the MAXS (Setpoint Maximum)
parameter corresponds to the value of the setpoint in engineering units when the
control input is at its maximum value.
24-5
MicroLogix 1500 Programmable Controllers User Manual
Setpoint MIN (MINS)
Input Parameter Descriptions
MINS - Setpoint Minimum
Address
Data
Format
Range
Type
User Program
Access
PD10:0.MINS
word (INT)
-32,768 to +32,767
control
read/write
If the SPV is read in engineering units, then the MINS (Setpoint Minimum) parameter
corresponds to the value of the setpoint in engineering units when the control input is
at its minimum value.
Note:
MinS - MaxS scaling allows you to work in engineering units. The
deadband, error, and SPV will also be displayed in engineering units.
The process variable, PV, must be within the range of 0 to 16383. Use of
MinS - MaxS does not minimize PID PV resolution.
Scaled errors greater than +32767 or less than -32768 cannot be represented. If the
scaled error is greater than +32767, it is represented as +32767. If the scaled error is
less than -32768, it is represented as -32768.
Old Setpoint Value (OSP)
Input Parameter Descriptions
OSP - Old Setpoint Value
Address
PD10:0.OSP
Data
Format
Range
Type
User Program
Access
word (INT)
-32,768 to +32,767
status
read only
The OSP (Old Setpoint Value) is substituted for the current setpoint, if the current
setpoint goes out of range of the setpoint scaling (limiting) parameters.
24-6
Process Control Instruction
Output Parameters
The table below shows the output parameter addresses, data formats, and types of user
program access. See the indicated pages for descriptions of each parameter.
Output Parameter Descriptions
Address
Data
Format
Range
Type
User Program
Access
For More
Information
CV - Control Variable
User-defined
word (INT)
0 - 16,383
control
read/write
24-7
CVP - Control Variable Percent
PD10:0.CVP
word (INT)
0 - 100
control
read/write
24-8
OL - Output Limit
PD10:0/OL
binary
1 = enabled
0 = disabled
control
read/write
24-8
CVH - Control Variable High Limit
PD10:0.CVH
word (INT)
0 - 100%
control
read/write
24-9
CVL - Control Variable Low Limit
PD10:0.CVL
word (INT)
0 - 100%
control
read/write
24-9
Output Parameter Descriptions
Address
Data
Format
Range
Type
User Program
Access
User-defined
word (INT)
0 - 16,383
control
read/write
Control Variable (CV)
CV - Control Variable
The CV (Control Variable) is user-defined. See the ladder rung below.
24-7
MicroLogix 1500 Programmable Controllers User Manual
Control Variable Percent (CVP)
Output Parameter Descriptions
CVP - Control Variable Percent
Address
Data
Format
Range
Type
User Program
Access
PD10:0.CVP
word (INT)
0 - 100
control
read/write
CVP (Control Variable Percent) displays the control variable as a percentage. The
range is 0 to 100%. If the PD10:0/AM bit is off (automatic mode), this value tracks
the control variable (CV) output. Any value written by the programming software will
be overwritten. If the PD10:0/AM bit is on (manual mode), this value can be set by
the programming software, and the control variable output tracks the control variable
percent value.
Output Limit (OL)
Output Parameter Descriptions
OL - Output Limit
Address
Data
Format
Range
Type
User Program
Access
PD10:0/OL
binary
1 = enabled
0 = disabled
control
read/write
An enabled (1) value enables output limiting to the values defined in PD10:0.CVH
(Control Variable High) and PD10.0.CVL (Control Variable Low).
A disabled (0) value disables OL (Output Limiting).
24-8
Process Control Instruction
Control Variable High Limit (CVH)
Output Parameter Descriptions
CVH - Control Variable High Limit
Address
Data
Format
Range
Type
User Program
Access
PD10:0.CVH
word (INT)
0 - 100%
control
read/write
When the output limit bit (PD10:0/OL) is enabled (1), the CVH (Control Value High)
you enter is the maximum output (in percent) that the control variable attains. If the
calculated CV exceeds the CVH, the CV is set (overridden) to the value you entered,
and the upper limit alarm bit (UL) is set.
When the output limit bit (PD10:0/OL) is disabled (0), the CVH value you enter
determines when the upper limit alarm bit (UL) is set.
If CV exceeds the maximum value, the output is not overridden, and the upper limit
alarm bit (UL) is set.
Control Variable Low Limit (CVL)
Output Parameter Descriptions
CVL - Control Variable Low Limit
Address
Data
Format
Range
Type
User Program
Access
PD10:0.CVL
word (INT)
0 - 100%
control
read/write
When the output limit bit (PD10:0/OL) is enabled (1), the CVL (Control Value Low)
you enter is the minimum output (in percent) that the Control Variable attains. If the
calculated CV is below the minimum value, the CV is set (overridden) to the CVL
value you entered, and the lower limit alarm bit (LL) is set.
When the output limit bit (PD10:0/OL) is disabled (0), the CVL value you enter
determines when the lower limit alarm bit (LL) is set. If CV is below the minimum
value, the output is not overridden, and the lower limit alarm bit (LL) is set.
24-9
MicroLogix 1500 Programmable Controllers User Manual
Tuning Parameters
The table below shows the tuning parameter addresses, data formats, and types of user
program access. See the indicated pages for descriptions of each parameter.
Tuning Parameter Descriptions
KC - Controller Gain - Kc
PD10:0.KC
Data
Format
word (INT)
0 to 32,767
control
User Program
Access
read/write
TI - Reset Term - Ti
PD10:0.TI
word (INT)
0 to 32,767
control
read/write
24-11
TD - Rate Term - Td
PD 10:0.TD
word (INT)
0 to 32,767
control
read/write
24-12
TM - Time Mode
LUT - Loop Update Time
ZCD - Zero Crossing Deadband
FF - Feed Forward Bias
SE - Scaled Error
AM - Automatic/Manual
CM - Control Mode
DB - PV in Deadband
RG - PLC 5 Gain Range
SC - Setpoint Scaling
TF - Loop Update Too Fast
DA - Derivative Action Bit
UL - CV Upper Limit Alarm
LL - CV Lower Limit Alarm
SP - Setpoint Out of Range
PV - PV Out of Range
DN - Done
EN - Enable
IS - Integral Sum
PD10:0.TM
PD10:0.LUT
PD10:0.ZCD
PD10:0.FF
PD10:0.SE
PD10:0/AM
PD10:0/CM
PD10:0/DB
PD10:0/RG
PD10:0/SC
PD10:0/TF
PD10:0/DA
PD10:0/UL
PD10:0/LL
PD10:0/SP
PD10:0/PV
PD10:0/DN
PD10:0/EN
PD10:0.IS
read/write
read/write
read/write
read/write
read only
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read/write
read only
read only
read/write
24-12
24-13
24-13
24-13
24-14
24-14
24-14
24-15
24-15
24-16
24-16
24-16
24-16
24-17
24-17
24-17
24-17
24-18
24-18
PD10:0.AD
0 or 1
1 to 1024
0 to 32,767
-16,383 to +16,383
-32,768 to +32,767
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
-2,147,483,648 to
2,147,483,647
-2,147,483,648 to
2,147,483,647
control
control
control
control
status
control
control
status
control
control
status
control
status
status
status
status
status
status
status
AD - Altered Derivative Term
binary
word (INT)
word (INT)
word (INT)
word (INT)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
binary (bit)
Lword (32bit INT)
Lword (32bit INT)
status
read only
24-18
24-10
Address
Range
Type
For More
Information
24-11
Process Control Instruction
Controller Gain (Kc)
Tuning Parameter Descriptions
Address
PD10:0.KC
KC - Controller Gain - Kc
Data
Format
word (INT)
Range
Type
0 to 32,767
control
User Program
Access
read/write
Gain Kc (word 3) is the proportional gain, ranging from 0 to 3276.7 (when RG = 0),
or 0 to 327.67 (when RG = 1). Set this gain to one-half the value needed to cause the
output to oscillate when the reset and rate terms (below) are set to zero.
Note:
Controller gain is affected by the reset and gain range (RG) bit. For
information, see“PLC 5 Gain Range (RG)” on page 24-15.
Reset Term (Ti)
Tuning Parameter Descriptions
TI - Reset Term - Ti
Address
PD10:0.TI
Data
Format
word (INT)
Range
Type
0 to 32,767
control
User Program
Access
read/write
Reset Ti (word 4) is the Integral gain, ranging from 0 to 3276.7 (when RG = 0), or
327.67 (when RG = 1) minutes per repeat. Set the reset time equal to the natural
period measured in the above gain calibration. A value of 1 will add the minimum
integral term into the PID equation.
Note:
Reset term is affected by the reset and gain range (RG) bit. For
information, see“PLC 5 Gain Range (RG)” on page 24-15.
24-11
MicroLogix 1500 Programmable Controllers User Manual
Rate Term (Td)
Tuning Parameter Descriptions
Address
PD 10:0.TD
TD - Rate Term - Td
Data
Format
word (INT)
Range
Type
0 to 32,767
control
User Program
Access
read/write
Rate Td (word 5) is the Derivative term. The adjustment range is 0 to 327.67 minutes.
Set this value to 1/8 of the integral gain Ti.
Note:
This word is not effected by the reset and gain range (RG) bit. For
information, see“PLC 5 Gain Range (RG)” on page 24-15.
Time Mode (TM)
Tuning Parameter Descriptions
TM - Time Mode
Address
PD10:0.TM
Data
Format
binary
Range
Type
0 or 1
control
User Program
Access
read/write
The time mode bit specifies when the PID is in timed mode (1) or STI mode (0). This
bit can be set or cleared by instructions in your ladder program.
When set for timed mode, the PID updates the CV at the rate specified in the loop
update parameter (PD10:0.LUT).
When set for STI mode the PID updates the CV every time the PID instruction is
scanned in the control program. When you select STI, program the PID instruction in
the STI interrupt subroutine. The STI routine should have a time interval equal to the
setting of the PID “loop update” parameter (PD10:0.LUT). Set the STI period in word
STI:0.SPM. For example, if the loop update time contains the value 10 (for 100 ms),
then the STI time interval must also equal 100 (for 100 ms).
Note:
24-12
When using timed mode, your processor scan time should be at least ten
times faster than the loop update time to prevent timing inaccuracies or
disturbances.
Process Control Instruction
Loop Update Time (LUT)
Tuning Parameter Descriptions
LUT - Loop Update Time
Address
PD10:0.LUT
Data
Format
word (INT)
Range
Type
1 to 1024
control
User Program
Access
read/write
The loop update time (word 13) is the time interval between PID calculations. The
entry is in 0.01 second intervals. Enter a loop update time five to ten times faster than
the natural period of the load. The natural period of the load is determined by setting
the reset and rate parameters to zero and then increasing the gain until the output
begins to oscillate. When in STI mode, this value must equal the STI time interval
value loaded in STI:0.SPM. The valid range is 0.01 to 10.24 seconds.
Zero Crossing Deadband (ZCD)
Tuning Parameter Descriptions
Address
ZCD - Zero Crossing Deadband
PD10:0.ZCD
Data
Format
word (INT)
Range
Type
0 to 32,767
control
User Program
Access
read/write
The deadband extends above and below the setpoint by the value entered. The
deadband is entered at the zero crossing of the process variable and the setpoint. This
means that the deadband is in effect only after the process variable enters the
deadband and passes through the setpoint.
The valid range is 0 to the scaled maximum, or 0 to 16,383 when no scaling exists.
Feed Forward Bias (FF)
Tuning Parameter Descriptions
FF - Feed Forward Bias
Address
PD10:0.FF
Data
Format
word (INT)
Range
Type
-16,383 to +16,383
control
User Program
Access
read/write
The feed forward bias is used to compensate for disturbances that may affect the CV
output.
24-13
MicroLogix 1500 Programmable Controllers User Manual
Scaled Error (SE)
Tuning Parameter Descriptions
SE - Scaled Error
Address
PD10:0.SE
Data
Format
word (INT)
Range
Type
-32,768 to +32,767
status
User Program
Access
read only
Scaled error is the difference between the process variable and the setpoint. The
format of the difference (E = SP-PV or E = PV-SP) is determined by the control mode
(CM) bit. See “Control Mode (CM)” on page 24-14.
Automatic / Manual (AM)
Tuning Parameter Descriptions
AM - Automatic/Manual
Address
PD10:0/AM
Data
Format
binary (bit)
Range
Type
0 or 1
control
User Program
Access
read/write
The auto/manual bit can be set or cleared by instructions in your ladder program.
When off (0), it specifies automatic operation. When on (1), it specifies manual
operation. In automatic operation, the instruction controls the control variable (CV).
In manual operation, the user/control program controls the CV. During tuning, set this
bit to manual.
Note:
Output limiting is also applied when in manual.
Control Mode (CM)
Tuning Parameter Descriptions
CM - Control Mode
Address
PD10:0/CM
Data
Format
binary (bit)
Range
Type
0 or 1
control
User Program
Access
read/write
Control mode, or forward-/reverse-acting, toggles the values E=SP-PV and E=PV-SP.
Forward acting (E=PV-SP) causes the control variable to increase when the process
variable is greater than the setpoint.
Reverse acting (E=SP-PV) causes the control variable to decrease when the process
variable is greater than the setpoint.
24-14
Process Control Instruction
PV in Deadband (DB)
Tuning Parameter Descriptions
DB - PV in Deadband
Address
PD10:0/DB
Data
Format
binary (bit)
Range
Type
0 or 1
status
User Program
Access
read/write
This bit is set (1) when the process variable is within the zero-crossing deadband
range.
PLC 5 Gain Range (RG)
Tuning Parameter Descriptions
RG - PLC 5 Gain Range
Address
PD10:0/RG
Data
Format
binary (bit)
Range
Type
0 or 1
control
User Program
Access
read/write
When set (1), the reset (TI) and gain range enhancement bit (RG) causes the reset
minute/repeat value and the gain multiplier (KC) to be enhanced by a factor of 10.
That means a reset multiplier of 0.01 and a gain multiplier of 0.01.
When clear (0), this bit allows the reset minutes/repeat value and the gain multiplier
value to be evaluated with a reset multiplier of 0.1 and a gain multiplier of 0.1.
Example with the RG bit set: The reset term (TI) of 1 indicates that the integral value
of 0.01 minutes/repeat (0.6 seconds/repeat) will be applied to the PID integral
algorithm. The gain value (KC) of 1 indicates that the error will be multiplied by 0.01
and applied to the PID algorithm.
Example with the RG bit clear: The reset term (TI) of 1 indicates that the integral
value of 0.1 minutes/repeat (6.0 seconds/repeat) will be applied to the PID integral
algorithm. The gain value (KC) of 1 indicates that the error will be multiplied by 0.1
and applied to the PID algorithm.
Note:
The rate multiplier (TD) is not affected by this selection.
24-15
MicroLogix 1500 Programmable Controllers User Manual
Setpoint Scaling (SC)
Tuning Parameter Descriptions
SC - Setpoint Scaling
Address
PD10:0/SC
Data
Format
binary (bit)
Range
Type
0 or 1
control
User Program
Access
read/write
The SC bit is cleared when setpoint scaling values are specified.
Loop Update Too Fast (TF)
Tuning Parameter Descriptions
TF - Loop Update Too Fast
Address
PD10:0/TF
Data
Format
binary (bit)
Range
Type
0 or 1
status
User Program
Access
read/write
The TF bit is set by the PID algorithm if the loop update time specified cannot be
achieved by the controller due to scan time limitations.
If this bit is set, correct the problem by updating your PID loop at a slower rate or
move the PID instruction to an STI interrupt routine. Reset and rate gains will be in
error if the instruction operates with this bit set.
Derivative Action Bit (DA)
Tuning Parameter Descriptions
DA - Derivative Action Bit
Address
PD10:0/DA
Data
Format
binary (bit)
Range
Type
0 or 1
control
User Program
Access
read/write
When set (1), the derivative (rate) action (DA) bit causes the derivative (rate)
calculation to be evaluated on the error instead of the process variable (PV). When
clear (0), this bit allows the derivative (rate) calculation to be evaluated where the
derivative is performed on the PV.
CV Upper Limit Alarm (UL)
Tuning Parameter Descriptions
UL - CV Upper Limit Alarm
Address
PD10:0/UL
Data
Format
binary (bit)
Range
Type
0 or 1
status
User Program
Access
read/write
The control variable upper limit alarm bit is set when the calculated CV output
exceeds the upper CV limit.
24-16
Process Control Instruction
CV Lower Limit Alarm (LL)
Tuning Parameter Descriptions
LL - CV Lower Limit Alarm
Address
PD10:0/LL
Data
Format
binary (bit)
Range
Type
0 or 1
status
User Program
Access
read/write
The control variable lower limit alarm bit is set (1) when the calculated CV output is
less than the lower CV limit.
Setpoint Out Of Range (SP)
Tuning Parameter Descriptions
SP - Setpoint Out of Range
Address
PD10:0/SP
Data
Format
binary (bit)
Range
Type
0 or 1
status
Range
Type
0 or 1
status
User Program
Access
read/write
This bit is set (1) when the setpoint:
•
exceeds the maximum scaled value, or
•
is less than the minimum scaled value.
PV Out Of Range (PV)
Tuning Parameter Descriptions
PV - PV Out of Range
Address
PD10:0/PV
Data
Format
binary (bit)
User Program
Access
read/write
The process variable out of range bit is set (1) when the unscaled process variable
•
exceeds 16,383, or
•
is less than zero.
Done (DN)
Tuning Parameter Descriptions
DN - Done
Address
PD10:0/DN
Data
Format
binary (bit)
Range
Type
0 or 1
status
User Program
Access
read only
The PID done bit is set (1) for one scan when the PID algorithm is computed. It resets
automatically.
24-17
MicroLogix 1500 Programmable Controllers User Manual
Enable (EN)
Tuning Parameter Descriptions
EN - Enable
Address
PD10:0/EN
Data
Format
binary (bit)
Range
Type
0 or 1
status
User Program
Access
read only
The PID enabled bit is set (1) whenever the PID instruction is enabled. It follows the
rung state.
Integral Sum (IS)
Tuning Parameter Descriptions
IS - Integral Sum
Address
PD10:0.IS
Data
Format
Lword (32bit INT)
This is the result of the integration
Range
Type
-2,147,483,648 to
2,147,483,647
status
User Program
Access
read/write
1
----- ∫ E ( dt ).
TI
Altered Derivative Term (AD)
Tuning Parameter Descriptions
AD - Altered Derivative Term
Address
PD10:0.AD
Data
Format
Lword (32bit INT)
Range
Type
-2,147,483,648 to
2,147,483,647
status
User Program
Access
read only
This long word is used internally to track the change in the process variable within the
loop update time.
24-18
Process Control Instruction
Runtime Errors
Error code 0036 appears in the status file when a PID instruction runtime error occurs.
Code 0036 covers the following PID error conditions, each of which has been
assigned a unique single byte code value that appears in the MSbyte of the second
word of the control block.
Description of Error Condition or
Conditions
Error Code
11H
Corrective Action
Change loop update time 0 < Dt < 1024
1. Loop update time
Dt > 1024
2. Loop update time
Dt = 0
12H
Proportional gain
Kc < 0
Change proportional gain Kc to 0 < Kc
13H
Integral gain (reset)
Change integral gain (reset) Ti to 0 < Ti
14H
Derivative gain (rate)
23H
Scaled setpoint min
31H
41H
Ti < 0
Change derivative gain (rate) Td to 0 < Td
Td < 0
MinS > Scaled setpoint max MaxS
Change scaled setpoint min MinS to
-32768 < MinS < MaxS < +32767
If you are using setpoint scaling and
MinS > setpoint SP > MaxS, or
If you are using setpoint scaling, then change
the setpoint SP to MinS < SP < MaxS, or
If you are not using setpoint scaling and
0 > setpoint SP > 16383,
If you are not using setpoint scaling, then change
the setpoint SP to 0 < SP < 16383.
then during the initial execution of the PID loop,
this error occurs and bit 11 of word 0 of the
control block is set. However, during
subsequent execution of the PID loop if an
invalid loop setpoint is entered, the PID loop
continues to execute using the old setpoint,
and bit 11 of word 0 of the control block is set.
Scaling Selected
1. Deadband < 0, or
Scaling Deselected
1. Deadband < 0, or
Scaling Selected
Change deadband to
0 < deadband <
(MaxS - MinS) < 16383
Scaling Deselected
Change deadband to
0 < deadband < 16383
24-19
MicroLogix 1500 Programmable Controllers User Manual
Error Code
Description of Error Condition or
Conditions
2. Deadband >
(MaxS – MinS)
24-20
Corrective Action
2. Deadband >
16383
51H
1. Output high limit < 0, or
2. Output high limit > 100
Change output high limit to
0 < output high limit < 100
52H
1. Output low limit < 0, or
2. Output low limit > 100
Change output low limit to
0 < output low limit < output high limit < 100
53H
Output low limit > output high limit
Change output low limit to
0 < output low limit < output high limit < 100
60H
PID is being entered for the second time. (PID
loop was interrupted by an I/O interrupt, which
is then interrupted by the PID STI interrupt.
You have at least three PID loops in your program:
One in the main program or subroutine file, one in
an I/O interrupt file, and one in the STI subroutine
file. You must alter your ladder program and
eliminate the potential nesting of PID loops.
Process Control Instruction
Analog I/O Scaling
To configure an analog input for use in a PID instruction, the analog data must be
scaled to match the PID instruction parameters. In the MicroLogix 1500 the process
variable (PV) in the PID instruction is designed to work with a data range of 0 to
16,383. The 1769 Compact I/O analog modules (1769-IF4 and 1769-OF2) have the
ability to scale analog data on board the module itself. Scaling data is required to
match the range of the analog input, to the input range of the PID instruction. The
ability to perform scaling in the I/O modules reduces the amount of programming
required in the system, and makes PID setup much easier.
The example shows a 1769-IF4 module. The IF4 has 4 inputs, which are individually
configurable. In this example analog input 0 is configured for 0 to 10V and is scaled
in engineering units. Word 0 is not being used in a PID instruction. Input #1 (word 1)
is configured for 4 to 20 mA operation with scaling configured for a PID instruction.
This configures the analog data for the PID instruction.
Field Device Input Signal
> 20.0 mA
20.0 mA
4.0 mA
< 4.0 mA
Analog Register Scaled Data
16,384 to 17,406
16,383
0
-819 to -1
The analog configuration screen is
accessed from within RSLogix 500.
Simply double click on the I/O
configuration item in the “Controller”
folder, and then double click on the
specific I/O card that you wish to
configure.
The configuration for the analog
output is virtually identical. Simply
address the PID control variable (CV)
to the analog output address, and
configure the analog output to “Scaled
for PID” behavior.
24-21
MicroLogix 1500 Programmable Controllers User Manual
Application Notes
The following paragraphs discuss:
•
Input/Output Ranges
•
Scaling to Engineering Units
•
Zero-crossing Deadband
•
Output Alarms
•
Output Limiting with Anti-reset Windup
•
The Manual Mode
•
Feed Forward
•
Time Proportioning Outputs
Input/Output Ranges
The input module measuring the process variable (PV) must have a full scale binary
range of 0 to 16383. If this value is less than 0 (bit 15 set), then a value of zero is used
for PV and the “Process var out of range” bit is set (bit 12 of word 0 in the control
block). If the process variable is greater than 16383 (bit 14 set), then a value of 16383
is used for PV and the “Process var out of range” bit is set.
The Control Variable, calculated by the PID instruction, has the same range of 0 to
16383. The Control Output (word 16 of the control block) has the range of 0 to
100%. You can set lower and upper limits for the instruction’s calculated output
values (where an upper limit of 100% corresponds to a Control Variable limit of
16383).
24-22
Process Control Instruction
Scaling to Engineering Units
Scaling lets you enter the setpoint and zero-crossing deadband values in engineering
units, and display the process variable and error values in the same engineering units.
Remember, the process variable PV must still be within the range 0-16383. The PV is
displayed in engineering units, however.
Select scaling as follows:
1. Enter the maximum and minimum scaling values MaxS and MinS in the PID
control block. The MinS value corresponds to an analog value of zero for the
lowest reading of the process variable, and MaxS corresponds to an analog value
of 16383 for the highest reading. These values reflect the process limits. Setpoint
scaling is selected by entering a non-zero value for one or both parameters. If you
enter the same value for both parameters, setpoint scaling is disabled.
For example, if measuring a full scale temperature range of -73°C (PV=0) to
+1156°C (PV=16383), enter a value of -73 for MinS and 1156 for MaxS.
Remember that inputs to the PID instruction must be 0 to 16383. Signal
conversions could be as follows:
Process limits
−73 to +1156° C
Transmitter output (if used)
+4 to +20 mA
Output of analog input module
0 to 16383
PID instruction, MinS to MaxS
−73 to +1156° C
2. Enter the setpoint (word 2) and deadband (word 9) in the same scaled engineering
units. Read the scaled process variable and scaled error in these units as well.
The control output percentage (word 16) is displayed as a percentage of the 0 to
16383 CV range. The actual value transferred to the CV output is always between
0 and 16383.
When you select scaling, the instruction scales the setpoint, deadband, process
variable, and error. You must consider the effect on all these variables when you
change scaling.
24-23
MicroLogix 1500 Programmable Controllers User Manual
Zero-Crossing Deadband DB
The adjustable deadband lets you select an error range above and below the setpoint
where the output does not change as long as the error remains within this range. This
lets you control how closely the process variable matches the setpoint without
changing the output.
+DB
SP
Error range
-DB
Time
Zero-crossing is deadband control that lets the instruction use the error for
computational purposes as the process variable crosses into the deadband until it
crosses the setpoint. Once it crosses the setpoint (error crosses zero and changes sign)
and as long as it remains in the deadband, the instruction considers the error value
zero for computational purposes.
Select deadband by entering a value in the deadband storage word (word 9) in the
control block. The deadband extends above and below the setpoint by the value you
enter. A value of zero inhibits this feature. The deadband has the same scaled units as
the setpoint if you choose scaling.
Output Alarms
You may set an output alarm on the control variable at a selected value above and/or
below a selected output percent. When the instruction detects that the control variable
has exceeded either value, it sets an alarm bit (bit LL for lower limit, bit UL for upper
limit) in the PID instruction. Alarm bits are reset by the instruction when the control
variable comes back inside the limits. The instruction does not prevent the control
variable from exceeding the alarm values unless you select output limiting.
Select upper and lower output alarms by entering a value for the upper alarm (CVH)
and lower alarm (CVL). Alarm values are specified as a percentage of the output. If
you do not want alarms, enter zero and 100% respectively for lower and upper alarm
values and ignore the alarm bits.
24-24
Process Control Instruction
Output Limiting with Anti-Reset Windup
You may set an output limit (percent of output) on the control variable. When the
instruction detects that the control variable has exceeded a limit, it sets an alarm bit
(bit LL for lower limit, bit UL for upper limit), and prevents the control variable from
exceeding either limit value. The instruction limits the control variable to 0 and 100%
if you choose not to limit.
Select upper and lower output limits by setting the limit enable bit (bit OL), and
entering an upper limit (CVH) and lower limit (CVL). Limit values are a percentage
(0 to 100%) of the control variable.
The difference between selecting output alarms and output limits is that you must
select output limiting to enable limiting. Limit and alarm values are stored in the
same words. Entering these values enables the alarms, but not limiting. Entering
these values and setting the limit enable bit enables limiting and alarms.
Anti-reset windup is a feature that prevents the integral term from becoming excessive
when the control variable reaches a limit. When the sum of the PID and bias terms in
the control variable reaches the limit, the instruction stops calculating the integral sum
until the control variable comes back in range. The integral sum is contained in
element, IS.
The Manual Mode
In the manual mode, the PID algorithm does not compute the value of the control
variable. Rather, it uses the value as an input to adjust the integral sum (IS) so that a
smooth transfer takes place upon re-entering the AUTO mode.
In the manual mode, the programmer allows you to enter a new CV value from 0 to
100%. This value is converted into a number from 0 to 16383 and written to the
Control Variable address. If your ladder program sets the manual output level, design
your ladder program to write to the CV address when in the manual mode. Note that
this number is in the range of 0 to 16383, not 0 to 100. Writing to the CV percent
(CVP) with your ladder program has no effect in the manual mode.
The example on the next page shows how you can manually control the control
variable (CV) output with your ladder program.
24-25
MicroLogix 1500 Programmable Controllers User Manual
PID Rungstate
If the PID rung is false, the integral sum (IS) is cleared and CV remains in its last
state.
Feed Forward or Bias
Applications involving transport lags may require that a bias be added to the CV
output in anticipation of a disturbance. This bias can be accomplished using the
processor by writing a value to the Feed Forward Bias element (word FF). (See page
24-13.) The value you write is added to the output, allowing a feed forward action to
take place. You may add a bias by writing a value between −16383 and +16383 to
word 6 with your programming terminal or ladder program.
PID Tuning
PID tuning requires a knowledge of process control. If you are inexperienced, it will
be helpful if you obtain training on the process control theory and methods used by
your company.
There are a number of techniques that can be used to tune a PID loop. The following
PID tuning method is general, and is limited in terms of handling load disturbances.
When tuning, we recommend that changes be made in the MANUAL mode, followed
by a return to AUTO. Output limiting is applied in the MANUAL mode.
Note:
24-26
•
This method requires that the PID instruction controls a non-critical
application in terms of personal safety and equipment damage.
•
The PID tuning procedure may not work for all cases. It is strongly
recommended to use a PID Loop tuner package for the best result (i.e..
RSTune, Rockwell Software catalog number 9323-1003D).
Process Control Instruction
Procedure
1. Create your ladder program. Make certain that you have properly scaled your
analog input to the range of the process variable PV and that you have properly
scaled your control variable CV to your analog output.
2. Connect your process control equipment to your analog modules. Download your
program to the processor. Leave the processor in the program mode.
!
ATTENTION: Ensure that all possibilities of machine motion have been considered
with respect to personal safety and equipment damage. It is possible that your output
CV may swing between 0 and 100% while tuning.
Note:
If you want to verify the scaling of your continuous system and/or
determine the initial loop update time of your system, go to the procedure
on page 24-29.
3. Enter the following values: the initial setpoint SP value, a reset Ti of 0, a rate Td
of 0, a gain Kc of 1, and a loop update of 5.
Set the PID mode to STI or Timed, per your ladder diagram. If STI is selected,
ensure that the loop update time equals the STI time interval.
Enter the optional settings that apply (output limiting, output alarm,
MaxS - MinS scaling, feedforward).
4. Get prepared to chart the CV, PV, analog input, or analog output as it varies with
time with respect to the setpoint SP value.
5. Place the PID instruction in the MANUAL mode, then place the processor in the
Run mode.
6. While monitoring the PID display, adjust the process manually by writing to the
CO percent value.
7. When you feel that you have the process under control manually, place the PID
instruction in the AUTO mode.
8. Adjust the gain while observing the relationship of the output to the setpoint over
time.
24-27
MicroLogix 1500 Programmable Controllers User Manual
9. When you notice that the process is oscillating above and below the setpoint in an
even manner, record the time of 1 cycle. That is, obtain the natural period of the
process.
Natural Period ≅ 4x deadtime
Record the gain value. Return to the MANUAL mode (stop the process if
necessary).
10. Set the loop update time (and STI time interval if applicable) to a value of 5 to 10
times faster than the natural period.
For example, if the cycle time is 20 seconds, and you choose to set the loop update
time to 10 times faster than the natural rate, set the loop update time to 200, which
would result in a 2-second rate.
11. Set the gain Kc value to 1/2 the gain needed to obtain the natural period of the process. For example, if the gain value recorded in step 9 was 80, set the gain to 40.
12. Set the reset term Ti to approximate the natural period. If the natural period is 20
seconds, as in our example, you would set the reset term to 3 (0.3 minutes per
repeat approximates 20 seconds).
13. Now set the rate Td equal to a value 1/8 that of the reset term. For our example,
the value 4 will be used to provide a rate term of 0.04 minutes per repeat.
14. Place the process in the AUTO mode. If you have an ideal process, the PID tuning
will be complete.
15. To make adjustments from this point, place the PID instruction in the MANUAL
mode, enter the adjustment, then place the PID instruction back in the AUTO
mode.
This technique of going to MANUAL, then back to AUTO ensures that most of
the “gain error” is removed at the time each adjustment is made. This allows you
to see the effects of each adjustment immediately. Toggling the PID rung allows
the PID instruction to restart itself, eliminating all of the integral buildup. You
may want to toggle the PID rung false while tuning to eliminate the effects of
previous tuning adjustments.
24-28
Process Control Instruction
Verifying the Scaling of Your Continuous System
To ensure that your process is linear, and that your equipment is properly connected
and scaled, do the following:
1. Place the PID instruction in manual and enter the following parameters:
v type:
v type:
v type:
0 for MinS
100 for MaxS
0 for CO%
2. Enter the REM Run mode and verify that PV=0.
3. Type: 20 in CO%
4. Record the PV = _______
5. Type: 40 in CO%.
6. Record the PV = _______
7. Type: 60 in CO%.
8. Record the PV = _______
9. Type: 80 in CO%.
10. Record the PV = _______
11. The values you recorded should be offset from CO% by the same amount. This
proves the linearity of your process. The following example shows an offset progression of fifteen.
CO 20% = PV 35%
CO 40% = PV 55%
CO 60% = PV 75%
CO 80% = PV 95%
If the values you recorded are not offset by the same amount:
•
Either your scaling is incorrect, or
•
the process is not linear, or
•
your equipment is not properly connected and/or configured.
Make the necessary corrections and repeat steps 2-10.
24-29
MicroLogix 1500 Programmable Controllers User Manual
Determining the Initial Loop Update Time
To determine the approximate loop update time that should be used for your process,
perform the following:
1. Place the normal application values in MinS and MaxS.
2. Type: 50 in CO%.
3. Type: 60 in CO% and immediately start your stopwatch.
4. Watch the PV. When the PV starts to change, stop your stopwatch. Record this
value. It is the deadtime.
5. Multiply the deadtime by 4. This value approximates the natural period. For
example, if:
deadtime = 3 seconds, then 4 x 3 = 12 seconds (≅ natural period)
6. Divide the value obtained in step 5 by 10. Use this value as the loop updated time.
For example, if:
natural period = 12 seconds, then 12/10 = 1.2 seconds.
Therefore, the value 120 would be entered as the loop update time.
(120 x 10 ms = 1.2 seconds)
7. Enter the following values: the initial setpoint SP value, a reset Ti of 0, a rate Td
of 0, a gain Kc of 1, and the loop update time determined in step 17.
Set the PID mode to STI or Timed, per your ladder diagram. If STI is selected,
ensure that the loop update time equals the STI time interval.
Enter the optional settings that apply (output limiting, output alarm,
MaxS - MinS scaling, feedforward).
8. Return to page 24-27 and complete the tuning procedure starting with step 4.
24-30
Communications Instructions
25
Communications Instructions
This chapter contains information about the Message (MSG) and Service
Communications (SVC), communication instructions. This chapter provides
information on:
•
how messaging works
•
what the instructions look like
•
how to configure and use the instructions
•
examples and timing diagrams
The communication instructions read or write data to another station.
Instruction
Used To:
Page
MSG
Transfer data from one device to another.
25-2
SVC
Interrupt the program scan to execute the
service communications part of the
operating cycle. The scan then resumes
at the instruction following the SVC
instruction.
25-24
25-1
MicroLogix 1500 Programmable Controllers User Manual
MicroLogix 1500 Messaging Overview
The MicroLogix 1500’s communication architecture is comprised of three primary
components:
•
Ladder Scan
•
Communications Buffers
•
Communication Queue
These three components determine when a message is transmitted by the controller.
For a message to transmit, it must be scanned on a true rung of logic. When scanned,
the message and the data defined within the message (if it is a write message) are
placed in a communication buffer. The controller continues to scan the remaining
user program. The message is processed and sent out the controller through the
communications port.
If a second message instruction is processed before the first message completes, the
second message and its data are placed in one of the three remaining communication
buffers. This process repeats whenever a message instruction is processed, until all
four buffers are in use.
When a buffer is available, the message and its associated data are placed in the buffer
immediately. If all four buffers are full when the next (fifth) message is processed,
the message request, not the data, is placed in a communications queue. The queue is
a message storage area that keeps track of messages that have not been allocated a
buffer. The queue operates as a first-in first-out (FIFO) storage area. The first
message request stored in the queue is the message that will be allocated a buffer as
soon as a buffer becomes available. The queue can accommodate all MSG
instructions in a ladder program.
When a message request in a buffer is completed, the buffer is released back to the
system. If a message is in the queue, that message is then allocated a buffer. At that
time, the data associated with the message is read from within the controller.
Note:
If a message instruction was in the queue, the data that is actually sent
out of the controller may be different than what was present when the
message instruction was first processed.
The buffer and queue mechanisms are completely automatic. Buffers are allocated
and released as the need arises, and message queuing occurs if buffers are full.
25-2
Communications Instructions
The MicroLogix 1500 controller initiates read and write messages through channel 0
when configured for the following protocols:
‡
'))XOO'XSOH[DQG')+DOI'XSOH[6ODYH
•
DH485
For a description of valid communication protocols, see “Understanding the
Communication Protocols” on page D-1.
The Message Instruction
The message instruction is an output instruction. Any preceding logic on the message
rung must be solved true before the message instruction can be processed. The
example below shows a Micrologix 1500 message instruction.
If B3/0 is on (1), the MSG rung is true, and MG11:0 will be processed. If one of the
four buffers is available, the message and its associated data will be processed
immediately.
Note:
How quickly the message is actually sent to the destination device
depends on a number of issues, including the selected channel’s
communication protocol, the baud rate of the communications port, the
number of retries needed (if any), and the destination device's readiness
to receive the message.
25-3
MicroLogix 1500 Programmable Controllers User Manual
The Message File
The MSG instruction built into the MicroLogix 1500 controller uses a MG data
file to process the message instruction. The MG data file, shown below, is
accessed using the MG prefix. Each message instruction utilizes an element
within a MG data file. For example, MG11:0 is the first element in message data
file 11.
Local Messages
The MicroLogix 1500 is capable of communicating using local or remote messages.
With a local message, all devices are accessible without a separate device acting as a
bridge. Different types of electrical interfaces may be required to connect to the
network, but the network is still classified as a local network. Remote messages use a
remote network, where devices are accessible only by passing or routing through a
device. Remote networks are discussed on page 25-14.
The following four examples represent different types of local networks.
Example 1 - Local DH485 Network with AIC+ (1761-NET-AIC) Interface
DH485 Network
AIC+
AIC+
AIC+
AIC+
A-B
SLC 5/03
Node 5
25-4
MicroLogix 1500
Node 10
PanelView
MicroLogix 1000
Node 12
SLC 5/04
Node 17
PanelView 550
Node 22
Communications Instructions
Example 2 - Local DeviceNet Network with DeviceNet Interface (1761-NET-DNI)
DeviceNet
Node 2
MicroLogix 1000
Node 5
Master
DANGER
DANGER
Node 1
SLC 5/03
MicroLogix 1500
Node 6
Node 10
DANGER
DANGER
MicroLogix 1500
Node 7
SLC 5/03
DANGER
DeviceNet
Node 55
Node 30
DANGER
25-5
MicroLogix 1500 Programmable Controllers User Manual
Example 3 - Local DF1 Half-Duplex Network
5RFNZHOO6RIWZDUH:,1WHOOLJHQW/,1;56/LQ[
RUKLJKHU6/&6/&DQG6/&
RU3/&SURFHVVRUVFRQILJXUHGIRU')+DOI
'XSOH[0DVWHU
56')+DOI'XSOH[3URWRFRO
0LFUR/RJL[
6/&3URFHVVRU
0LFUR/RJL[
3URJUDPPDEOH
0RGXODU&RQWUROOHU
3URJUDPPDEOH
&RQWUROOHU
6ODYH
&RQWUROOHUV
Note:
It is recommended that isolation (1761-NET-AIC) be provided between the
MicroLogix 1500 and the modem.
Example 4 - Local DF1 Full-Duplex Network (point-to-point)
MicroLogix 1500
Optical Isolator
(1761-NET-AIC recommended)
1761-CBL-PM02
Personal Computer
25-6
&RQWUROOHUZLWK
.(,QWHUIDFH
0RGXOH6ODYH
6ODYH
6ODYH
6/&)L[HG,2
Communications Instructions
Configuring a Local Message
The RSLogix Message Setup Screen is shown below. Descriptions of each of the
elements follow.
25-7
MicroLogix 1500 Programmable Controllers User Manual
“This Controller” Parameters
Communication Command
The MicroLogix 1500 controller supports six different types of communications
commands. If the target device supports any of these command types, the
MicroLogix 1500 should be capable of exchanging data with the device. Supported
commands include:
Communication
Command
500CPU Read
The target device is compatible with and supports the SLC 500 command set (all
MicroLogix 1000 and 1500 controllers), use this setting to read data.
500CPU Write
The target device is compatible with and supports the SLC 500 command set (all
MicroLogix 1000 and 1500 controllers), use this setting to send data.
485CIF Read1
The target device is compatible with and supports the 485CIF (PLC2) command
set, use this setting to read data.
485CIF Write1
The target device is compatible with and supports the 485CIF (PLC2) command
set, use this setting to send data
PLC5 Read
The target device is compatible with and supports the PLC5 command set, use this
setting to read data.
PLC5 Write
The target device is compatible with and supports the PLC5 command set, use this
setting to send data.
1.
25-8
Description
The Common Interface File (CIF) in the MicroLogix 1500 and SLC 500 processors is File 9. The CIF in the
MicroLogix 1000 controller is Integer File 7.
Communications Instructions
Data Table Address
This variable defines the starting address in the local controller. A valid address is
any configured data file within the controller, except system status, PD and MG files.
Size in Elements
This variable defines the amount of data (number of local elements) to exchange with
the target device.
The maximum amount of data that can be transferred via a MSG instruction is 103
words (206 bytes) and is determined by the destination data type. The destination data
type is defined by the type of message: read or write.
For Read Messages: When a read message is used, the destination file is the data file
in the local or originating processor.
Note:
Input or output data file types are not valid for read messages.
For Write Messages: When a write message is used, the destination file is the data
file in the target processor.
25-9
MicroLogix 1500 Programmable Controllers User Manual
The maximum number of elements that can be transmitted or received are shown in
the table below. You cannot cross file types when sending messages. For example,
you cannot read a timer into an integer file and you cannot write counters to a timer
file. The only exception to this rule is that long integer data can be read/written to bit
or integer files.
The table below is not intended to illustrate file compatibility, only the
maximum number of elements that can be exchanged in each case.
Note:
Message Type
Read or Write
Message
Format
SLC or
PLC
SLC
PLC
Read
SLC or
PLC
Write
SLC or
PLC
Read
CIF
Write
CIF
I
Input
S
Status
R
Control
O
Output
T
Timer
N
Integer (16-bit)
B
Bit
C
Counter
L
Long Integer (32-bit)
This Controller
(MicroLogix 1500)
File Type
B, N
L
C, R
T
T
B, N
B, N
L
I, O
I, O, B, N
L
B, N
L
T, C, R
I, O, B, N
L
T, C, R
Target Device
File Type
Maximum Number of Elements in
This Controller (MicroLogix 1500)
S, B, N
L
C, R
T
T
I, O
L
I, O, S, B, N
S, B, N
L
S, B, N
103
51
34
34
20
103
103
51
103
103
51
103
51
34
103
51
34
CIF (Common Interface
File)
CIF (Common Interface
File)
Channel
This variable defines the communication channel that will be used to transmit the
message request. This value is factory-set to channel 0 for the MicroLogix 1500 and
cannot be changed.
25-10
Communications Instructions
“Target Device” Parameters
Message Timeout
This value defines how long, in seconds, the message instruction has to complete its
operation once it has started. Timing begins when the false to true rung transition
occurs, enabling the message. If the timeout period expires, the message errors out.
The default value is 5 seconds.
If the message timeout is set to zero, the message instruction will never timeout. The
user must set (1) the Time Out (TO) bit to flush a message instruction from its buffer
if the destination device does not respond to the communications request.
Data Table Address/Offset
This variable defines the starting address in the target controller. The data table
address is used for a 500CPU or PLC5 type MSG. A valid address is any valid,
configured data file within the target device whose file type is recognized by the
MicroLogix 1500 controller.
The data table offset is used for 485CIF type messages. A valid offset is any value in
the range 0 to 255 and indicates the word or byte offset into the target’s Common
Interface File (CIF). The type of device determines whether it is a word or byte offset.
The amount of data to be exchanged is determined by the “Size in Elements” variable
described on page 25-9.
Local Node Address
This is the destination device's node number if the devices are connected on a network
(DH485 using 1761-NET-AIC, DeviceNet using 1761-NET-DNI, or DF1 HalfDuplex).
Note:
To initiate a broadcast message on a DH485 network, set the local node
address to -1.
Local/Remote
This variable defines the type of communications that will be used. Use local when
you need point-to-point communications via DF1 Full-Duplex or network
communications like DH485 using 1761-NET-AIC, DeviceNet using 1761-NETDNI, or DF1 Half-Duplex.
25-11
MicroLogix 1500 Programmable Controllers User Manual
“Control Bits” Parameters
Ignore if Timed Out (TO)
Address
MG11:0/TO
Data Format
Binary
Range
On - Off
Type
Control
User Program Access
Read / Write
The Timed Out Bit (TO) can be set in your application to remove an active message
instruction from processor control. You can create your own timeout routine by
monitoring the EW and ST bits to start a timer. When the timer times out, you can set
the TO bit, which will remove the message from the system. The controller resets the
TO bit the next time the associated MSG rung goes from false to true.
An easier method is to use the message timeout variable described on page 25-11,
because it simplifies the user program. This built-in timeout control is in effect
whenever the message timeout is nonzero. It defaults to 5 seconds, so unless you
change it, the internal timeout control is automatically enabled.
When the internal timeout is used and communications are interrupted, the MSG
instruction will timeout and error after the set period of time expires. This allows the
control program to retry the same message or take other action, if desired.
To disable the internal timeout control, enter zero for the MSG instruction timeout
parameter. If communications are interrupted, the processor will wait forever for a
reply. If an acknowledge (ACK) is received, indicated by the ST bit being set, but the
reply is not received, the MSG instruction will appear to be locked up, although it is
actually waiting for a reply from the target device.
Enable (EN)
Address
MG11:0/EN
Data Format
Binary
Range
On - Off
Type
Control
User Program Access
Read / Write
The Enable Bit (EN) is set when rung conditions go true and the MSG is enabled.
The MSG is enabled when the command packet is built and put into one of the MSG
buffers, or the request is put in the MSG queue. It remains set until the message
transmission is completed and the rung goes false. You may clear this bit when either
the ER or DN bit is set in order to re-trigger a MSG instruction with true rung
conditions on the next scan.
Do not set this bit from the control program.
Important:
25-12
Communications Instructions
Enabled and Waiting (EW)
Address
MG11:0/EW
Data Format
Binary
Range
On - Off
Type
Status
User Program Access
Read Only
The Enabled and Waiting Bit (EW) is set after the enable bit is set and the message
is in the buffer and waiting to be sent.
Do not set or clear this bit. It is informational only.
Important:
Error (ER)
Address
MG11:0/ER
Data Format
Binary
Range
On - Off
Type
Status
User Program Access
Read Only
The Error Bit (ER) is set when message transmission has failed. An error code is
written to the MSG File. The ER bit is cleared the next time the associated rung goes
from false to true.
Do not set or clear this bit. It is informational only.
Important:
Done (DN)
Address
MG11:0/DN
Data Format
Binary
Range
On - Off
Type
Status
User Program Access
Read Only
The Done Bit (DN) is set when the message is transmitted successfully. The DN bit is
cleared the next time the associated rung goes from false to true.
Do not set or clear this bit. It is informational only.
Important:
Start (ST)
Address
MG11:0/ST
Data Format
Binary
Range
On - Off
Type
Status
User Program Access
Read Only
The Start Bit (ST) is set when the processor receives acknowledgment (ACK) from
the target device. The ST bit is cleared when the DN, ER, or TO bit is set.
Do not set or clear this bit. It is informational only.
Important:
25-13
MicroLogix 1500 Programmable Controllers User Manual
Remote Messages
The MicroLogix 1500 is also capable of remote or off-link messaging. Remote
messaging is the ability to exchange information with a device that is not connected to
the local network. This type of connection requires a device on the local network to
act as a bridge or gateway to the other network. The illustration below shows two
networks, a DH485 and a DH+ network. The SLC 5/04 processor at DH485 node 17
is configured for passthru operation. Devices that are capable of remote messaging
and are connected on either network can initiate read or write data exchanges with
devices on the other network, based on each device’s capabilities. In this example,
node 12 is a MicroLogix 1500. The MicroLogix 1500 can respond to remote message
requests from nodes 40 or 51 on the DH+ network and it can initiate a message to any
node on the DH+ network.
The MicroLogix 1000 can respond to remote message requests, but it
cannot initiate them.
Note:
This functionality is also available on Ethernet by replacing the SLC 5/04 at node 19
with an SLC 5/05 processor.
DH485 and DH+ Networks
DH485 Network
AIC+
AIC+
AIC+
Node 17
AIC+
A-B
SLC 5/03
Node 5
MicroLogix 1000
Node 10
MicroLogix 1500
Node 12
SLC 5/04
Node 19
PanelView
PanelView 550
Node 22
DH+ Network
Node 51
SLC 5/04
Node 40
PLC5
The illustration below shows a DeviceNet network using DeviceNet Interfaces (1761NET-DNI) connected to a Ethernet network using an SLC 5/05. In this configuration,
controllers on the DeviceNet network can reply to requests from devices on the
Ethernet network, but cannot initiate communications to devices on Ethernet.
25-14
Communications Instructions
DeviceNet and Ethernet Networks
DeviceNet Network
DNI
DNI
DNI
DNI
A-B
SLC 5/03
Node 5
MicroLogix 1000
Node 10
MicroLogix 1500
Node 17
SLC 5/05
Node 38
PanelView
PanelView 550
Node 54
Ethernet Network
SLC 5/05
SLC 5/05
PLC-5E
Configuring a Remote Message
You configure for remote capability in the RSLogix Message Setup screen.
The message configuration shown below is the MicroLogix 1500 at node 12 on the
DH485 network. This message will read five elements of data to address N:50:0 in the
SLC 5/04 controller at node 51 on the DH+ network. The SLC 5/04 at Node 23 of the
DH+ network is configured for passthru operation.
25-15
MicroLogix 1500 Programmable Controllers User Manual
Link ID 1
DH485 Network
AIC+
AIC+
AIC+
Node 17
AIC+
A-B
SLC 5/03
Node 5
MicroLogix 1000
Node 10
MicroLogix 1500
Node 12
SLC 5/04
Node 23
DH+ Network
Node 63 octal
(51 dec.)
SLC 5/04
PanelView
PanelView 550
Node 22
Link ID 100
Node 40 octal
(32 dec.)
PLC-5
Local Bridge Address
This variable defines the bridge address on the local network. In the example, node
12 is writing data to node 51 on DH+. The SLC 5/04 on DH485 is node 17. This
variable sends the message to node 17.
Remote Bridge Address
This variable defines the remote node address of the bridge device. In this example,
the remote bridge address is set to zero, because the target device, SLC 5/04 at node
63 (octal) is a remote-capable device. If the target device is remote-capable, the
remote bridge address is not required. If the target device is not remote-capable (SLC
500, SLC 5/01, SLC 5/02, and MicroLogix 1000 Series A, B and C), the remote
bridge address is required.
Remote Station Address
This variable is the final destination address of the message instruction. In this
example, integer file 50 elements 0-4 of the SLC 5/04 on DH+ at node 63 (octal)
sends data to the MicroLogix 1500 controller at node 12 on DH485.
25-16
Communications Instructions
Remote Bridge Link ID
This variable is a user-assigned value that identifies the remote network as a number.
This number must be used by any device initiating remote messaging from the DH485
side of the network. Any controller on the local DH485 network sending data to a
device on the DH+ network should use the same value for the remote bridge link ID.
Set the Link ID in the General tab on the Channel Configuration screen. The Link ID
value is a user-defined number between 1 and 65,535. All devices that can initiate
remote messages and are connected to the local must have the same number for this
variable.
25-17
MicroLogix 1500 Programmable Controllers User Manual
MSG Instruction Error Codes
When the processor detects an error during the transfer of message data, the processor
sets the ER bit and enters an error code that you can monitor from your programming
software.
Error
Code
25-18
Description of Error Condition
02H
Target node is busy. NAK No Memory retries by link layer exhausted.
03H
Target node cannot respond because message is too large.
04H
Target node cannot respond because it does not understand the command parameters OR the control
block may have been inadvertently modified.
05H
Local processor is off-line (possible duplicate node situation).
06H
Target node cannot respond because requested function is not available.
07H
Target node does not respond.
08H
Target node cannot respond.
09H
Local modem connection has been lost.
0BH
Target node does not accept this type of MSG instruction.
0CH
Received a master link reset (one possible source is from the DF1 master).
10H
Target node cannot respond because of incorrect command parameters or unsupported command.
12H
Local channel configuration protocol error exists.
13H
Local MSG configuration error in the Remote MSG parameters.
15H
Local channel configuration parameter error exists.
16H
Target or Local Bridge address is higher than the maximum node address.
17H
Local service is not supported.
18H
Broadcast is not supported.
30H
PCCC Description: Remote station host is not there, disconnected, or shutdown.
37H
Message timed out in local processor.
39H
Local communication channel reconfigured while MSG active.
3AH
STS in the reply from target is invalid.
40H
PCCC Description: Host could not complete function due to hardware fault.
45H
MSG reply cannot be processed. Either Insufficient data in MSG read reply or bad network address
parameter.
50H
Target node is out of memory.
60H
Target node cannot respond because file is protected.
Communications Instructions
Error
Code
Description of Error Condition
70H
PCCC Description: Processor is in Program Mode.
80H
PCCC Description: Compatibility mode file missing or communication zone problem.
90H
PCCC Description: Remote station cannot buffer command.
B0H
PCCC Description: Remote station problem due to download.
C0H
PCCC Description: Cannot execute command due to active IPBs.
D0H
No IP address configured for the network, – or–
Bad command - unsolicited message error, – or–
Bad address - unsolicited message error, – or–
No privilege - unsolicited message error
D1H
Maximum connections used - no connections available
D2H
Invalid internet address or host name
D3H
No such host / Cannot communicate with the name server
D4H
Connection not completed before user– specified timeout
D5H
Connection timed out by the network
D7H
Connection refused by destination host
D8H
Connection was broken
D9H
Reply not received before user– specified timeout
DAH
No network buffer space available
E1H
PCCC Description: Illegal Address Format, a field has an illegal value.
E2H
PCCC Description: Illegal Address format, not enough fields specified.
E3H
PCCC Description: Illegal Address format, too many fields specified.
E4H
PCCC Description: Illegal Address, symbol not found.
E5H
PCCC Description: Illegal Address Format, symbol is 0 or greater than the maximum number of
characters support by this device.
E6H
PCCC Description: Illegal Address, address does not exist, or does not point to something usable by
this command.
E7H
Target node cannot respond because length requested is too large.
E8H
PCCC Description: Cannot complete request, situation changed (file size, for example) during multi–
packet operation.
E9H
PCCC Description: Data or file is too large. Memory unavailable.
EAH
PCCC Description: Request is too large; transaction size plus word address is too large.
EBH
Target node cannot respond because target node denies access.
ECH
Target node cannot respond because requested function is currently unavailable.
25-19
MicroLogix 1500 Programmable Controllers User Manual
Error
Code
Description of Error Condition
EDH
PCCC Description: Resource is already available; condition already exists.
EEH
PCCC Description: Command cannot be executed.
EFH
PCCC Description: Overflow; histogram overflow.
F0H
PCCC Description: No access
F1H
Local processor detects illegal target file type.
F2H
PCCC Description: Invalid parameter; invalid data in search or command block.
F3H
PCCC Description: Address reference exists to deleted area.
F4H
PCCC Description: Command execution failure for unknown reason; PLC– 3 histogram overflow.
F5H
PCCC Description: Data conversion error.
F6H
PCCC Description: The scanner is not able to communicate with a 1771 rack adapter. This could be
due to the scanner not scanning, the selected adapter not being scanned, the adapter not responding,
or an invalid request of a “DCM BT (block transfer)”.
F7H
PCCC Description: The adapter is not able to communicate with a module.
F8H
PCCC Description: The 1771 module response was not valid - size, checksum, etc.
F9H
PCCC Description: Duplicated Label.
FAH
Target node cannot respond because another node is file owner (has sole file access).
FBH
Target node cannot respond because another node is program owner (has sole access to all files).
FCH
PCCC Description: Disk file is write protected or otherwise inaccessible (off– line only).
FDH
PCCC Description: Disk file is being used by another application; update not performed (off–line only).
FFH
Local communication channel is shut down.
Note:
25-20
For 1770-6.5.16 DF1 Protocol and Command Set Reference Manual
users: The MSG error code reflects the STS field of the reply to your
MSG instruction.
•
Codes E0 - EF represent EXT STS codes 0 - F.
•
Codes F0 - FC represent EXT STS codes 10 - 1C.
Communications Instructions
Timing Diagram for MicroLogix 1500 MSG Instruction
The following section describes the timing diagram for a MicroLogix 1500 MSG
instruction.
Target node
receives packet.
Rung goes true.
➀
➁
➂
Target node processes packet
successfully and returns data
(read) or writes data (success).
➄ ➅
1
EN 0
1
EW 0
1
ST 0
1
DN 0
1
ER 0
1
TO 0
1. If there is room in any of the four active message buffers when the MSG rung
becomes true and the MSG is scanned, the EN and EW bits are set. If this were a
MSG write instruction, the source data would be transferred to the message buffer
at this time.
(Not shown in the diagram.) If there is no room in the four message buffers, the
message request is put in the MSG queue, only the EN bit is set. The MSG queue
works on a first-in, first-out basis that allows the MicroLogix 1500 controller to
remember the order in which the MSG instructions were enabled. When a buffer
becomes available, the first message in the queue is placed into the buffer, and the
EW bit is set (1).
The control program does not have access to the MicroLogix 1500
Note:
communications queue.
Once the EN bit is set (1), it remains set until the entire message process is
complete and either the DN, ER, or TO bit is set (1). The MSG Timeout period
begins timing when the EN bit is set (1). If the timeout period expires before the
25-21
MicroLogix 1500 Programmable Controllers User Manual
MSG instruction completes its function, the ER bit is set (1), and an error code
(37H) is placed in the MG File to inform you of the timeout error.
2. At the next end of scan, REF, or SVC instruction, the MicroLogix 1500 controller
determines if it should examine the communications queue for another instruction.
The controller bases its decision on the state of the Channel 0 Communication
Servicing Selection (CSS) and Message Servicing Selection (MSS) bits, the network communication requests from other nodes, and whether previous MSG
instructions are already in progress. If the MicroLogix 1500 controller determines
that it should not access the queue, the MSG instruction remains as it was. Either
the EN and EW bits remain set (1) or only the EN bit is set (1) until the next end
of scan, REF, or SVC instruction.
If the MicroLogix 1500 controller determines that it has an instruction in the
queue, it unloads the communications queue entries into the message buffers until
all four message buffers are full. If an invalid message is unloaded from the
communications queue, the ER bit is set (1), and a code is placed in the MG file to
inform you of an error. When a valid MSG instruction is loaded into a message
buffer, the EN and EW bits are set (1).
The MicroLogix 1500 controller then exits the end of scan, REF, or SVC portion
of the scan. The controller’s background communication function sends the
messages to the target nodes specified in the MSG instruction. Depending on the
state of the CSS and MSS bits, you can have up to four MSG instructions active at
any given time.
3. If the target node successfully receives the message, it sends back an acknowledge
(ACK). The ACK causes the processor to clear (0) the EW bit and set (1) the ST
bit. The target node has not yet examined the packet to see if it understands your
request.
Once the ST bit is set (1), the controller waits for a reply from the target node. The
target node is not required to respond within any give time frame.
If the Target Node faults or power cycles during the message
Note:
transaction, you will never receive a reply. This is why you should
use a Message Timeout value in your MSG instruction.
25-22
Communications Instructions
4. Step 4 is not shown in the timing diagram. If you do not receive an ACK, step 3
does not occur. Instead either no response or a no acknowledge (NAK) is
received. When this happens, the ST bit remains clear (0).
No response may be caused by:
• the target node is not there
• the message became corrupted in transmission
• the response was corrupted in response transmission
A NAK may be caused by:
• target node is busy
• target node received a corrupt message
• the message is too large
When a NAK occurs, the EW bit is cleared (0), and the ER bit is set (1),
indicating that the MSG instruction failed.
5. Following the successful receipt of the packet, the target node sends a reply
packet. The reply packet contains one of the following responses:
• successful write request.
• successful read request with data
• failure with error code
At the next end of scan, REF, or SVC instruction, following the target node’s
reply, the MicroLogix 1500 controller examines the message from the target
device. If the reply is successful, the DN bit is set (1), and the ST bit is cleared
(0). If it is a successful read request, the data is written to the data table. The MSG
instruction function is complete.
If the reply is a failure with an error code, the ER bit is set (1), and the ST bit is
cleared (0). The MSG instruction function is complete.
6. If the DN or ER bit is set (1) and the MSG rung is false, the EN bit is cleared (0)
the next time the MSG instruction is scanned.
See “Examples: Ladder Logic” on page 25-27 for examples using the MSG
instruction.
25-23
MicroLogix 1500 Programmable Controllers User Manual
Service Communications (SVC)
Under normal operation the MicroLogix 1500 controller processes communications
once every time it scans the control program. If you require the communications port
to be scanned more often, or if the ladder scan is long, you can add an SVC (Service
Communications) instruction to your control program. The SVC instruction is used
to improve communications performance/throughput, but will also cause the ladder
scan to be longer.
Simply place the SVC instruction on a rung within the control program. When the
rung is scanned, the controller will service any communications that need to take
place. You can place the SVC instruction on a rung without any preceding logic, or
you can condition the rung with a number of communications status bits. The table on
page 25-25 shows the available status file bits.
Note:
The amount of communications servicing performed is controlled by the
Communication Servicing Selection Bit (CSS) and Message Servicing
Selection Bit (MSS) in the Channel 0 Communication Configuration
File.
For best results, place the SVC instruction in the middle of the control program.You
may not place an SVC instruction in a Fault, DII, STI, or I/O Event subroutine.
Channel Select
When using the SVC instruction, you must select the channel to be serviced. The
channel select variable is a one-word bit pattern that determines which channel is
serviced. Each bit corresponds to a specific channel. For example, bit 0 equals
channel 0. When any bit is set (1), the corresponding channel is serviced.
Enter a 1 (decimal value 1 turns on bit 0) to allow channel 0 to be serviced.
If you enter 0, only the DAT will be serviced.
Note:
25-24
The DAT is not a selectable channel. It is always serviced when the
SVC instruction executes.
Communications Instructions
Communication Status Bits
The following communication status bits allow you to customize or monitor
communications servicing. See “System Status File” on page G-1 for additional
information about the status file.
Address
CS0:4/0
CS0:4/1
CS0:4/2
CS0:4/4
Description
Incoming Command Pending
Incoming Message Reply Pending
Outgoing Message Command Pending
Communications Active Bit
Application Example
The SVC instruction is used when you want to execute a communication function,
such as transmitting a message, prior to the normal service communication portion of
the operating scan.
You can place this rung after a message write instruction. CS0:4/MCP is set when the
message instruction is enabled and put in the communications queue. When
CS0:4/MCP is set (1), the SVC instruction is evaluated as true and the program scan
is interrupted to execute the service communication’s portion of the operating scan.
The scan then resumes at the instruction following the SVC instruction.
The example rung shows a conditional SVC which will be processed only when an
outgoing message is in the communications queue.
Note:
You may program the SVC instruction unconditionally across the rungs.
This is the normal programming technique for the SVC instruction.
25-25
MicroLogix 1500 Programmable Controllers User Manual
25-26
Communications Instruction
25
Examples: Ladder Logic
Enabling the MSG Instruction for Continuous Operation
Enabling the MSG Instruction Via User Supplied Input
0000
As long as input I:1/0 is set, or anytime it becomes set, the MSG instruction in the next rung will be enabled. This program is
an example of controlling when the MSG instruction operates. Input I:1/0 could be any user-supplied bit to control when MSGs
are sent.
MSG Enable Bit
I:1
MG11:0
B3:0
L
0
EN
0
The MSG instruction will be enabled with each false-to-true transition of bit B3:0/0.
B3:0
0001
0
0002
MSG Done Bit
MG11:0
DN
MSG
Read/Write Message
MSG File
MG11:0
Setup Screen
EN
DN
ER
B3:0
U
0
MSG Error Bit
MG11:0
ER
0003
END
25-27
MicroLogix 1500 Programmable Controllers User Manual
Using Local Messaging
Example 1 - Local Read from a 500CPU
In the display above the MicroLogix 1500 processor reads 10 elements from Local
Node 2’s N7 file, starting at word N7:50. The 10 words are placed in this controller’s
integer file starting at word N7:0. If five seconds elapse before the message
completes, error bit MG11:0/ER is set, indicating that the instruction timed out. The
device at node 2 understands the SLC 500 processor family (SLC 500, SLC 5/01,
SLC 5/02, SLC 5/03, SLC 5/04, SLC 5/05, MicroLogix 1000, and MicroLogix 1500)
protocol.
25-28
Communications Instruction
Function Key
This
Controller
Description
Communication Specifies the type of message. Valid types are: 500CPU Read, 500CPU Write, 485CIF Read,
Command
485CIF Write, PLC5 Read, PLC5 Write.
Data Table
Address
For a Read (Destination) this is the address in the initiating processor which is to receive data.
Valid file types are B, T, C, R, N, and L.
For a Write (Source) this is the address in the initiating processor which is to send data.
Valid file types are B, T, C, R, N, I, O, and L.
Target
Device
Size in
elements
Defines the length of the message in elements. One word elements are limited to a maximum length
of 1-103. Two word elements are limited to a maximum length of 1-51. Three word elements are
limited to a maximum length of 1-34.
Channel
Identifies the physical channel used for the message communication. Always channel 0.
Message
Timeout
Defines the length of the message timer in seconds. A timeout of 0 seconds means that there is no
timer and the message will wait indefinitely for a reply. Valid range is 0-255 seconds.
Data Table
Address
For a Read (Source) this is the address in the target processor which is to send data.
For a Write (Destination) this is the address in the target processor which is to receive data.
Valid file types are S, B, T, C, R, N, I, O, and L. See “Valid File Type Combinations” below.
Local Node
Address
Specifies the node number of the processor that is receiving the message. Valid range is 0-31 for
DH485 protocol, or 0-254 for DF1 Half- and Full-Duplex protocols.
Local/Remote
Specifies whether the message is local or remote.
Valid File Type Combinations
For 500CPU messages, the only valid combinations of local file types and target file
types are:
Local Data Types
Target Data Types
O1, I1., B, N, L
O, I, S, B, N, L
T
T
C
C
R
R
1. Output and input data types are not valid
local data types for read messages.
Mixing file types of different size elements is not allowed, except for one-word
elements (O, I, S, B, and N) and two-word elements (L).
25-29
MicroLogix 1500 Programmable Controllers User Manual
Example 2 - Local Read from a 485CIF
In the display above the MicroLogix 1500 processor reads five elements (words) from
Local Node 2’s CIF file, starting at word 20 (or byte 20 for non-SLC 500 devices).
The five elements are placed in your integer file starting at word N7:0. If 15 seconds
elapse before the message completes, error bit MG11:0/ER is set, indicating that the
instruction timed out. The device at node 2 understands the 485CIF (PLC-2
emulation) protocol.
25-30
Communications Instruction
Function Key
This
Controller
Description
Communication Specifies the type of message. Valid types are: 500CPU Read, 500CPU Write, 485CIF Read,
Command
485CIF Write, PLC5 Read, PLC5 Write.
Data Table
Address
For a Read (Destination) this is the address in the initiating processor which is to receive data.
Valid file types are B, T, C, R, N, and L.
For a Write (Source) this is the address in the initiating processor which is to send data.
Valid file types are B, T, C, R, N, I, O, and L.
Target
Device
Size in
Elements
Defines the length of the message in elements. One word elements are limited to a maximum length
of 1-103. Two word elements are limited to a maximum length of 1-51. Three word elements are
limited to a maximum length of 1-34.
Channel
Identifies the physical channel used for the message communication. Always channel 0.
Message
Timeout
Defines the length of the message timer in seconds. A timeout of 0 seconds means that there is no
timer and the message will wait forever for a reply. Valid range is 0-255 seconds.
Data Table
Offset
This is the word offset value in the common interface file (byte offset for non-SLC device) in the
target processor, which is to send the data.
Local Node
Address
Specifies the node number of the processor that is receiving the message. Valid range is 0-31 for
DH– 485 protocol, or 0-254 for DF-1 Half- and Full-Duplex protocols.
Local/Remote
Specifies whether the message is local or remote.
25-31
MicroLogix 1500 Programmable Controllers User Manual
Example 3 - Local Read from a PLC-5
In the display above the MicroLogix 1500 processor reads 10 elements from Local
Node 2’s N7 file, starting at word N7:50. The 10 words are placed in your integer file
starting at word N7:0. If five seconds elapse before the message completes, error bit
MG11:0/ER is set, indicating that the instruction timed out. The device at node 2
understands the PLC-5 processor protocol.
Function Key
This
Controller
Description
Communication Specifies the type of message. Valid types are: 500CPU Read, 500CPU Write, 485CIF Read,
Command
485CIF Write, PLC5 Read, PLC5 Write.
Data Table
Address
For a Read (Destination) this is the address in the initiating processor which is to receive data.
Valid file types are B, T, C, R, N, and L. See “Valid File Type Combinations” below.
For a Write (Source) this is the address in the initiating processor which is to send data.
Valid file types are B, T, C, R, N, I, O, and L. See “Valid File Type Combinations” below.
25-32
Size in
Elements
Defines the length of the message in elements. One-word elements are limited to a maximum length
of 1-103. Two-word elements are limited to a maximum length of 1-51. Counter and control elements
are limited to a maximum length of 1-34. Timer elements are limited to a maximum length of 1-20.
Channel
Identifies the physical channel used for the message communication. Always channel 0.
Communications Instruction
Target
Device
Message
Timeout
Defines the length of the message timer in seconds. A timeout of 0 seconds means that there is no
timer and the message will wait indefinitely for a reply. Valid range is 0-255 seconds.
Data Table
Address
For a Read (Source) this is the address in the target processor which is to send data.
Valid file types are S, B, T, C, R, N, and L. See “Valid File Type Combinations” below.
For a Write (Destination) this is the address in the target processor which is to receive data.
Valid file types are S, B, T, C, R, N, I, O, and L. See “Valid File Type Combinations” below.
Local Node
Address
Specifies the node number of the processor that is receiving the message. Valid range is 0-31 for
DH485 protocol, or 0-254 for DF1 protocol.
Local/Remote
Specifies whether the message is local or remote.
Valid File Type Combinations
For PLC-5 messages, the only valid combinations of local file types and target file
types are:
Local File Types
Target File Types
O1, I1., B, N, L
O, I, S, B, N, L
T
T
C
C
R
R
1. Output and input data types are not valid
local data types for read messages.
Mixing file types of different size elements is not allowed, except for one-word
elements (O, I, S, B, and N) and two-word elements (L).
25-33
MicroLogix 1500 Programmable Controllers User Manual
Using Remote Messaging
The MicroLogix 1500 can pass a MSG instruction to a target device on a remote
network.
Example 1 - Communicating with A-B processors using a 1785-KA5
Device A
SLC 5/04
Modular I/O Controller
Device B
PLC-5/40 with
1785-KA5 Module
Node 5
Node 1
(octal)
Node 3
(octal)
DH+
Link ID = 2
(57.6Kbaud)
DH+
Link ID = 2
(57.6Kbaud)
25-34
Device C
MicroLogix 1500
DH485 Node 7
DH485
Link ID = 1
(19.2Kbaud)
Node 2
Communications Instruction
MicroLogix 1500 (Device C) to SLC 5/04 Processor (Device A) via 1785-KA5
Channel is set to 0 since the originating command is initiated by a MicroLogix 1500
processor on the DH485 (Link ID 1).
Local Bridge Node Address is set to 7 since this is the DH485 node address used by
the 1785-KA5 communication interface module.
Remote Bridge Node Address is set to 0 (not used) because communication is from
one remote-capable device to another remote-capable device.
Remote Station Address is the SLC 5/04 processor at node address 1.
Remote Bridge Link ID is the link ID of the remote DH+ network with the 1785KA5 and the SLC 5/04 processor (Link ID 2).
Note:
Important:
Data Table Addresses, the Size in Elements and Message Timeout are
all user-specified.
Set the MicroLogix 1500’s Link ID in the channel configuration
screen.
25-35
MicroLogix 1500 Programmable Controllers User Manual
MicroLogix 1500 Processor (Device C) to a PLC-5 (Device B) via 1785-KA5
Channel is set to 0 since the originating command is initiated by a MicroLogix
processor on the DH485 (Link ID 1).
Local Bridge Node Address is set to 7 since this is the DH485 node address used by
the 1785-KA5 communication interface module.
Remote Bridge Node Address is set to 0 (not used) because communication is from
one remote-capable device to another remote-capable device.
Remote Station Address is the PLC-5 processor at node address 3.
Remote Bridge Link ID is the link ID of the remote DH+ network with the 1785KA5 and the PLC-5 processor (Channel 1A, Link ID 2).
Note:
Important:
25-36
Data Table Addresses, the Size in Elements and Message Timeout are
all user-specified.
Set the MicroLogix 1500’s Link ID in the channel configuration
screen.
Communications Instruction
Example 2 - Passthru via DH485 Channel 0 of the SLC 5/04
Processor
TERM
A
B
COM
SHLD
CHS GND
TX
TX
TERM
TX
PWR
A
B
DC SOURCE
COM
CABLE
SHLD
CHS GND
TX
TX
TX
EXTERNAL
PWR
DC SOURCE
CABLE
EXTERNAL
25-37
MicroLogix 1500 Programmable Controllers User Manual
MicroLogix 1500 Processor (Device D) to SLC 5/04 Processor (Device A) via
an SLC 5/04 Processor (Device C)
(Passthru using Channel 0 DH485)
Channel is set to 0 since the originating command is initiated by a MicroLogix 1500
processor on the DH485 network.
Local Bridge Node Address is set to 1 since this is the DH485 node address used by
the passthru SLC 5/04 processor.
Remote Bridge Node Address is set to 0 (not used) because communication is from
one remote-capable device to another remote-capable device.
Remote Station Address is the SLC 5/04 processor at node address 1.
Remote Bridge Link ID is the link ID of the remote DH+ network with both
SLC 5/04 processors (Channel 1, Link ID 2).
Note:
Important:
25-38
Data Table Addresses, the Size in Elements and Message Timeout are
all user-specified.
Set the MicroLogix 1500’s Link ID in the channel configuration
screen.
Communications Instruction
MicroLogix 1500 Processor (Device D) to PLC–5 (Device B) via an SLC 5/04
Processor
(Passthru using Channel 0 DH485)
Channel is set to 0 since the originating command is initiated by an MicroLogix 1500
processor on the DH485 network.
Local Bridge Node Address is set to 1 since this is the DH485 node address used by
the passthru SLC 5/04 processor.
Remote Bridge Node Address is set to 0 (not used) because communication is from
one Internet–capable device to another remote-capable device.
Remote Station Address is the PLC-5 processor at node address 3.
Remote Bridge Link ID is the link ID of the remote DH+ network with the SLC 5/04
processor (Channel 1, Link ID 2) and PLC-5 processor (Channel 1A, Link ID 2).
Note:
Important:
Data Table Addresses, the Size in Elements and Message Timeout are
all user-specified.
Set the MicroLogix 1500’s Link ID in the channel configuration
screen.
25-39
MicroLogix 1500 Programmable Controllers User Manual
Example - Passthu using Two 1785-KA5s
Device A
Device B
MicroLogix 1500
MicroLogix 1500
Device D
Node 2
PLC-5/40 with
1785-KA5 Module
Node 10
Node 3
(octal)
Link ID = 6
DH485
(19.2Kbaud)
Device C
PLC-5/40 with
1785-KA5 Module
Link ID = 8
DH485
(19.2Kbaud)
Node 20
Link ID = 4
DH+
(17.6Kbaud)
Node 10
MicroLogix 1500 (Device A) to a MicroLogix 1500 (Device B) (Using two
1785-KA5s)
25-40
Communications Instruction
Channel is set to 0 since the command is sent from the MicroLogix 1500’s DH485
channel onto local Link ID 4.
Local Bridge Node Address is set to 20 since it is the bridge device (Link ID 4) that
the command is to be sent through (device D).
Remote Bridge Node Address is set to 0 (not used) because communication is from
one remote-capable device to another remote-capable device.
Remote Station Address is set to 2 since this is the DH485 address the destination
device resides at on the destination link (Link ID 8).
Remote Bridge Link ID is set to 8 since this is the destination link that the
destination device resides on.
Note:
The Communication Command can be 500CPU Read or Write, or PLC5
Read or Write.
Note:
Data Table Addresses, the Size in Elements and Message Timeout are
all user-specified.
Important:
You must set the Link ID to 6 in the Channel Configuration screen.
25-41
MicroLogix 1500 Programmable Controllers User Manual
25-42
Specifications
A
Specifications
Table 1: General Specifications
Description
1764-24BWA
1764-24AWA
1764-28BXB
Number of I/O
12 inputs
12 outputs
12 inputs
12 outputs
16 inputs
12 outputs
Line Power
85 to 265V ac
85 to 265V ac
20.4 to 30V dc
Power Supply Inrush
120V ac = 25 A
for 8 ms
240V ac = 40 A
for 4 ms
120V ac = 25 A
for 8 ms
240V ac = 40 A
for 4 ms
24V dc = 4 A
for 150 ms
User Power Output
24V dc at 400 mA,
400 µF max.
none
none
Input Circuit Type
24V dc, sink/source
120V ac
24V dc, sink/source
Output Circuit Type
relay
relay
6 relay,
6 FET transistor
(24V dc source)
Operating Temp.
+0°C to +55°C (+32°F to +131°F) ambient
Storage Temp.
-40°C to +85°C (-40°F to +185°F) ambient1
Operating Humidity
5% to 95% relative humidity (non-condensing)
Vibration
Operating: 0.015 in. peak-to-peak displacement 10-57 Hz, 5g 57-500 Hz
Relay Operation: 2g
Shock (without Data
Access Tool installed)
Operating: 30g panel mounted (15g DIN Rail mounted)
Relay operation: 7.5g panel mounted (5g DIN Rail mounted)
Non-Operating: 40g panel mounted (30g DIN Rail mounted)
Shock (with Data Access
Tool installed)
Operating: 20g panel mounted (15g DIN Rail mounted)
Relay operation: 7.5g panel mounted (5g DIN Rail mounted)
Non-Operating: 30g panel mounted (20g DIN Rail mounted)
1. Recommended storage temperature for maximum battery life (5 years typical with normal operating/
storage conditions) of the 1764-RTC and 1764-MM1RTC is -40°C to +40°C (-40°F to +104°F). Battery
life is significantly shorter at elevated temperatures.
A-1
MicroLogix 1500 Programmable Controllers User Manual
Table 1: General Specifications
Description
1764-24BWA
1764-24AWA
1764-28BXB
Agency Certification
• UL 508
• C-UL under CSA C22.2 no. 142
• Class I, Div. 2, Groups A, B, C, D
(UL 1604, C-UL under CSA C22.2 no. 213)
• CE compliant for all applicable directives
Electrical/EMC
The module has passed testing at the following levels:
• IEC1000-4-2: 4 kV contact, 8 kV air, 4 kV indirect
• IEC1000-4-3: 10 V/m
• IEC1000-4-4: 2 kV, 5 kHz; communications cable: 1 kV, 5 kHz
• IEC1000-4-5: communications cable1 kv galvanic gun
-I/O: 2 kV CM, 1 kV DM,
-Power Supply (1764-24AWA/1764-24BWA): 4 kV CM, 2 kV DM
-Power Supply (1764-28BXB): 0.5 kV CM, 0.5 kV DM
• IEC1000-4-6: 10V, communications cable 3V
Terminal Screw Torque
1.13 Nm (10 in-lb) rated; 1.3 Nm (12 in-lb) maximum
Table 2: Input Specifications
Description
1764-24BWA and 1764-28BXB
Inputs 0 thru 7
Inputs 8 and Higher
On State Voltage Range 79 to 132V ac
14 to 30.0V dc at 30°C
(86°F)
14 to 26.4V dc at 55°C
(131°F)
10 to 30.0V dc at 30°C
(86°F)
10 to 26.4V dc at 55°C
(131°F)
Off State Voltage Range 0 to 20V ac
0 to 5V dc
Operating Frequency
47 Hz to 63 Hz
0 Hz to 20 kHz
On State Current:
• minimum
• nominal
• maximum
• 5.0 mA at 79V ac
• 2.5 mA at 14V dc
• 12.0 mA at 120V ac • 7.3 mA at 24V dc
• 16.0 mA at 132V ac • 12.0 mA at 30V dc
0 Hz to 500 Hz1
• 2.0 mA at 10V dc
• 8.9 mA at 24V dc
• 12.0 mA at 30V dc
Off State Leakage
Current
2.5 mA minimum
1.5 mA minimum
Nominal Impedance
12k ohms at 50 Hz
10k ohms at 60 Hz
3.3k ohms
2.7k ohms
Inrush Current (max.)
250 mA at 120V ac
Not Applicable
Not Applicable
1. Scan-time dependant.
A-2
1764-24AWA
Specifications
Note:
The 1764-24AWA input circuits (inputs 0-11) do not support adjustable
filter settings. They have maximum turn-on and maximum turn-off times
of 20 milliseconds.
Table 3: Response Times for High-Speed dc Inputs 0 Through 7 (applies to 1764-24BWA and 176428BXB)
Maximum
High-Speed
Counter
Frequency @
50% Duty
Cycle (KHz)
Filter Setting
(ms)
Minimum ON
Delay (ms)
Maximum ON
Delay (ms)
Minimum
OFF Delay
(ms)
Maximum
OFF Delay
(ms)
20.000
0.025
0.005
0.025
0.005
0.025
6.700
0.075
0.040
0.075
0.045
0.075
5.000
0.100
0.050
0.100
0.060
0.100
2.000
0.250
0.170
0.250
0.210
0.250
1.000
0.500
0.370
0.500
0.330
0.500
0.500
1.000
0.700
1.000
0.800
1.000
0.200
2.000
1.700
2.000
1.600
2.000
0.125
4.000
3.400
4.000
3.600
4.000
0.063
8.0001
6.700
8.000
7.300
8.000
0.031
16.000
14.000
16.000
14.000
16.000
1. This is the default setting.
A-3
MicroLogix 1500 Programmable Controllers User Manual
Table 4: Response Times for Normal dc Inputs 8 Through 11 (1764-24BWA) and 8 Through 15
(1764-28BXB)
Maximum
Frequency @
50% Duty
Cycle (kHz)
Filter Setting
(ms)
Minimum ON
Delay (ms)
Maximum ON
Delay (ms)
Minimum
OFF Delay
(ms)
Maximum
OFF Delay
(ms)
1.000
0.500
0.090
0.500
0.020
0.500
0.500
1.000
0.500
1.000
0.400
1.000
0.250
2.000
1.100
2.000
1.300
2.000
0.125
4.000
2.800
4.000
2.700
4.000
0.063
8.0001
5.800
8.000
5.300
8.000
0.031
16.000
11.000
16.000
10.000
16.000
1. This is the default setting.
Table 5: Relay Contact Rating Table 1764-24AWA, -24BWA, -28BXB
Maximum Volts
Amperes
Make
Break
240V ac
7.5A
0.75A
120V ac
15A
1.5A
Amperes
Continuous
2.5A
Voltamperes
Make
Break
1800VA
180VA1
125V dc
0.22A2
1.0A
28VA
24V dc
1.2A2
2.0A
28VA
1. The total load controlled by thet 1764-24AWA and 1764-24BWA is limited to 1440VA (break).
2. For dc voltage applications, the make/break ampere rating for relay contacts can be determined by
dividing 28 VA by the applied dc voltage. For example, 28 VA/48V dc = 0.58A. For dc voltage
applications less than 14V, the make/break ratings for relay contacts cannot exceed 2A.
Table 6: Output Specifications - Maximum Continuous Current
Specification
1764-24AWA/BWA
1764-28BXB
8A
8A
at 150V Maximum
24A
18A
at 240V Maximum
20A
18A
Current per Common
Current per Controller
A-4
Specifications
¡
Table 7: 1764-28BXB FET Output Specifications
Specification
User Supply Voltage
General Operation
(Outputs 2 thru 7)
High Speed Operation1
(Outputs 2 and 3 Only)
minimum
20.4V dc
20.4V dc
maximum
26.4V dc
26.4V dc
at maximum load
current
1V dc
Not Applicable
at maximum surge
current
2.5V dc
Not Applicable
maximum load
1A at 55°C (131°F)
1.5A at 30°C (86°F)
100 mA
minimum load
1.0 mA
10 mA
maximum leakage
1.0 mA
1.0 mA
peak current
4.0A
Not Applicable
maximum surge
duration
10 msec
Not Applicable
maximum rate of
repetition at 30°C
(86°F)
once every second
Not Applicable
maximum rate of
repetition at 55°C
(131°F)
once every 2
seconds
Not Applicable
Current per
Common
maximum total
6A
Not Applicable
Turn-On Time
maximum
0.1 msec
6 µsec
Turn-Off Time
maximum
1.0 msec
18 µsec
Repeatability
maximum
n/a
2 µsec
Drift
maximum
n/a
1 µsec per 5°C
(1 µsec per 9°F)
On-State Voltage
Drop
Current Rating per
Point
Surge Current per
Point
1. Outputs 2 and 3 are designed to provide increased functionality over the other FET outputs (4
through 7). They may be used like the other FET transistor outputs, but in addition, within a limited
current range, they may be operated at a higher speed. Outputs 2 and 3 also provide a pulse train
output (PTO) or pulse width modulation output (PWM) function.
A-5
MicroLogix 1500 Programmable Controllers User Manual
Table 8: Working Voltage (1764-24AWA)
Specification
Power Supply Input to Backplane Isolation
1764-24AWA
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (IEC Class 2 reinforced
insulation)
Input Group to Backplane Isolation and Input Group
to Input Group Isolation
Verified by one of the following dielectric tests:
151V ac for 1 second or 2145V dc for 1 second
132V Working Voltage (IEC Class 2 reinforced
insulation)
Output Group to Backplane Isolation
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (IEC Class 2 reinforced
insulation)
Output Group to Output Group Isolation
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (basic insulation) 150V
Working Voltage (IEC Class 2 reinforced
insulation).
A-6
Specifications
Table 9: Working Voltage (1764-24BWA)
Specification
Power Supply Input to Backplane Isolation
1764-24BWA
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (IEC Class 2 reinforced
insulation)
Power Supply User 24V Output to Backplane
Isolation
Verified by one of the following dielectric tests:
600V ac for 1 second or 848V dc for 1 second
50V Working Voltage (IEC Class 2 reinforced
insulation)
Input Group to Backplane Isolation and Input Group
to Input Group Isolation
Verified by one of the following dielectric tests:
1200V ac for 1 second or 1697V dc for 1
second
75V dc Working Voltage (IEC Class 2 reinforced
insulation)
Output Group to Backplane Isolation
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (IEC Class 2 reinforced
insulation).
Output Group to Output Group Isolation.
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (basic insulation) 150V
Working Voltage (IEC Class 2 reinforced
insulation)
A-7
MicroLogix 1500 Programmable Controllers User Manual
Table 10: Working Voltage (1764-28BXB)
Specification
1764-28BXB
Input Group to Backplane Isolation and Input Group
to Input Group Isolation
Verified by one of the following dielectric tests:
1200V ac for 1 second or 1697V dc for 1
second
75V dc Working Voltage (IEC Class 2 reinforced
insulation)
FET Output Group to Backplane Isolation and FET
Outputs Group to Group
Verified by one of the following dielectric tests:
1200V ac for 1 second or 1697V dc for 1
second
75V dc Working Voltage (IEC Class 2 reinforced
insulation)
Relay Output Group to Backplane Isolation
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (IEC Class 2 reinforced
insulation)
Relay Output Group to Relay and FET Output Group
Isolation
Verified by one of the following dielectric tests:
1836V ac for 1 second or 2596V dc for 1
second
265V Working Voltage (basic insulation) 150V
Working Voltage (IEC Class 2 reinforced
insulation)
A-8
132 mm 122 mm
(5.19 in.) (4.813 in.)
DIN rail center line.
147 mm
(5.78 in.)
Base Unit
168 mm
(6.62 in.)
38 mm
(1.49 in.)
Expansion I/O
35 mm
(1.37 in.)
Specifications
Controller Dimensions
See also page 2-13 for “Base Unit Mounting Dimensions”.
A-9
MicroLogix 1500 Programmable Controllers User Manual
Compact I/O Dimensions
Panel Mounting
Right End Cap
Compact I/O
Compact I/O
122.6±0.2
(4.826±0.008)
28.5
(1.12)
35
(1.38)
Compact I/O
132
(5.197)
Host Controller
For more than 2 modules: (number of modules - 1) X 35 mm (1.38 in.)
Refer to host controller documentation for this dimension.
End Cap
32
(1.26)
18 (0.71)
118
(4.65)
Depth: 85 (3.35)
Dimensions are in mm (inches).
Transistor Output Transient Pulses
Refer to page 3-14 for “Transistor Output Transient Pulses”.
A-10
NOTE: All dimensions
are in mm (inches). Hole
spacing tolerance:
±0.4 mm (0.016 in.)
Replacement Parts
B
Replacement Parts
This chapter contains the following information:
•
a table of MicroLogix 1500 replacement parts
•
procedure for replacing the lithium battery
•
illustrations of the MicroLogix 1500 replacement doors and terminal blocks
MicroLogix 1500 Replacement Kits
The table below provides a list of replacement parts and their catalog number.
Description
Catalog Number
ESD Barrier
1764-RPL-TRM1
Base Terminal Doors (See page B-6.)
1764-RPL-TDR1
Processor Access Door (See page B-6.)
1764-RPL-CDR1
Door Combination Kit
ESD Barrier
Terminal Door
Access Door
Base Comms Door (See page B-7.)
Trim Pots/Mode Switch Cover Door (See page B-7.)
1764-RPL-DR
17-Point Terminal Block (for inputs on 1764-24AWA and -24BWA bases)
(See page B-8.)
1764-RPL-TB1
21-Point Terminal Block (for inputs of 1764-28BXB and outputs for all base
units)(See page B-8.)
1764-RPL-TB2
B-1
MicroLogix 1500 Programmable Controllers User Manual
Lithium Battery (1747-BA)
Follow the procedure below to ensure proper battery operation and reduce personnel
hazards.
Handling
!
•
Use only for the intended operation.
•
Do not ship or dispose of cells except according to recommended procedures.
•
Do not ship on passenger aircraft.
ATTENTION: Do not charge the batteries. An explosion could result or the cells
could overheat causing burns.
Do not open, puncture, crush, or otherwise mutilate the batteries. A possibility of
an explosion exists and/or toxic, corrosive, and flammable liquids would be
exposed.
Do not incinerate or expose the batteries to high temperatures. Do not attempt to
solder batteries. An explosion could result.
Do not short positive and negative terminals together. Excessive heat can build up
and cause severe burns.
Storing
Store lithium batteries in a cool, dry environment, typically +20°C to +25°C (+68°F to
77°F) and 40% to 60% humidity. Store the batteries and a copy of the battery
instruction sheet in the original container, away from flammable materials.
B-2
Replacement Parts
Transporting
One or Two Batteries - Each battery contains 0.23 grams of lithium. Therefore, up to
two batteries can be shipped together within the United States without restriction.
Regulations governing shipment to or within other countries may differ.
Three or More Batteries - Procedures for the transportation of three or more
batteries shipped together within the United States are specified by the Department of
Transportation (DOT) in the Code of Federal Regulations, CFR49, “Transportation.”
An exemption to these regulations, DOT - E7052, covers the transport of certain
hazardous materials classified as flammable solids. This exemption authorizes
transport of lithium batteries by motor vehicle, rail freight, cargo vessel, and cargoonly aircraft, providing certain conditions are met. Transport by passenger aircraft is
not permitted.
A special provision of DOT-E7052 (11th Rev., October 21, 1982, par. 8-a) provides
that:
“Persons that receive cell and batteries covered by this exemption may reship
them pursuant to the provisions of 49 CFR 173.22a in any of these packages
authorized in this exemption including those in which they were received.”
The Code of Federal Regulations, 49 CFR 173.22a, relates to the use of packaging
authorized under exemptions. In part, it requires that you must maintain a copy of the
exemption at each facility where the packaging is being used in connection with
shipment under the exemption.
Shipment of depleted batteries for disposal may be subject to specific regulation of
the countries involved or to regulations endorsed by those countries, such as the IATA
Articles Regulations of the International Air Transport Association, Geneva,
Switzerland.
Important:
Regulations for transportation of lithium batteries are periodically
revised.
B-3
MicroLogix 1500 Programmable Controllers User Manual
Installing
Follow the procedure below to ensure proper replacement battery installation.
Important:
Do not remove the permanent battery when installing replacement
battery.
1. Insert battery into replacement battery pocket with wires facing up.
2. Insert replacement battery wire connector into connector port.
3. Secure battery wires under wire latch (as shown below).
Replacement Battery Pocket
Replacement Battery
DC INPUTS
Battery Connector Wires
24V SINK/SOURCE
DC/RELAY OUT
24V SOURCE
Permanent Battery
(DO NOT REMOVE)
Wire Latch
Connector Port
Wire Connector
B-4
Replacement Parts
Disposing
!
ATTENTION: Do not incinerate or dispose of lithium batteries in general trash
collection. Explosion or violent rupture is possible. Batteries should be collected
for disposal in a manner to prevent against short circuiting, compacting, or
destruction of case integrity and hermetic seal.
For disposal, batteries must be packaged and shipped in accordance with
transportation regulations, to a proper disposal site. The U.S. Department of
Transportation authorizes shipment of “Lithium batteries for disposal” by motor
vehicle only in regulation 173.1015 of CFR 49 (effective January 5, 1983). For
additional information contact:
U.S. Department of Transportation
Research and Special Programs Administration
400 Seventh Street, S.W.
Washington, D.C. 20590
Although the Environmental Protection Agency at this time has no regulations
specific to lithium batteries, the material contained may be considered toxic, reactive,
or corrosive. The person disposing of the material is responsible for any hazard
created in doing so. State and local regulations may exist regarding the disposal of
these materials.
For a lithium battery product safety data sheet, contact the manufacturer:
Sanyo Energy Corporation
2001 Sanyo Avenue
San Diego, CA 92173
(619) 661-4801
Tadiran Electronic Industries
2 Seaview Blvd.
Port Washington, NY 11050
(516) 621-4980
B-5
MicroLogix 1500 Programmable Controllers User Manual
Replacement Doors
The following figures illustrate the procedure for installing the MicroLogix 1500
replacement doors.
Base Terminal Door
L2
5
85-26C
VA
VAC 0
VDC
VAC 1
VDC
O/0
VAC 2
VDC
O/1
VAC 3
VDC
O/2
VAC 4
VDC
O/3
O/5
O/4
O/7
O/6
O/8
VAC 5
VDC
O / 10
O/9
24 BW
A
O / 11
L1
1
3
2
Processor Access Door
B-6
Replacement Parts
Base Comms Door
1
2
Trim Pots/Mode Switch Cover Door
1
2
B-7
MicroLogix 1500 Programmable Controllers User Manual
Replacement Terminal Blocks
The figure below illustrates how to replace the MicroLogix 1500 terminal blocks.
B-8
Troubleshooting Your System
C
Troubleshooting Your System
This chapter describes how to troubleshoot your controller. Topics include:
•
understanding the controller LED status
•
controller error recovery model
•
identifying controller faults
•
calling Allen-Bradley for assistance
C-1
MicroLogix 1500 Programmable Controllers User Manual
Understanding the Controller LED Status
The controller status LEDs provide a mechanism to determine the current status of the
controller if a programming device is not present or available.
LED
D.C. INPUTS
POWER
RUN
Color
Indicates
off
no input power
green
power on
off
controller is not in Run mode or REM
Run
green
controller is in Run mode or REM Run
green
flashing
system is not in Run mode; memory
module transfer is in progress
off
no fault detected
24V SINK / SOURCE
POWER
DC/RELAY OUT
RUN
FAULT
FORCE
FAULT
BAT. LO
COMM 0
red flashing faulted user program
24V SOURCE
red
processor hardware fault or critical
fault
off
no forces installed
amber
forces installed
BATTERY
LOW
off
battery OK
red
battery needs replacement
COMM 0
off
flashes when communications are
active
DCOMM
FORCE
green
DCOMM
INPUTS
off
user configured communications
Mode 15 active
green
default communications Mode 15
active
off
input is not energized
amber
input is energized (logic status)
OUTPUTS off
amber
C-2
output is not energized
output is energized (logic status)
Troubleshooting Your System
When Operating Normally
The POWER and RUN LEDs are on. If a force condition is active, the FORCE LED
turns on and remains on.
When an Error Exists
If an error exists within the controller, the controller LEDs operate as described in the
following tables.
If the LEDS
indicate:
All LEDS
off
The Following
Error Exists
No input
power or
power supply
error
Probable
Cause
No Line
Power
Power
Supply
Overloaded
If the LEDS
The Following
Probable
indicate:
Error Exists
Cause
Power and
Hardware faulted Processor
FAULT LEDs on
Hardware
solid
Error
Loose Wiring
If the LEDS
The Following
Probable
indicate:
Error Exists
Cause
Power LED on Application fault Hardware/
Software
and FAULT LED
Major Fault
flashing
Detected
Recommended Action
Verify proper line voltage and
connections to the controller.
This problem can occur intermittently
if power supply is overloaded when
output loading and temperature
varies.
Recommended Action
Cycle power. Contact your local AllenBradley representative if the error
persists.
Verify connections to the controller.
Recommended Action
1. Monitor Status File Word S:6 for
major error code. See page C-6 for
more information.
2. Remove hardware/software condition
causing fault.
3. Clear Major Error Halted flag, bit
S2:1/13.
4. Attempt a controller Run mode entry.
If unsuccessful, repeat recommended
action steps above or contact your
local Allen-Bradley distributor.
C-3
MicroLogix 1500 Programmable Controllers User Manual
Controller Error Recovery Model
Use the following error recovery model to help you diagnose software and hardware
problems in the micro controller. The model provides common questions you might
ask to help troubleshoot your system. Refer to the recommended pages within the
model for further help.
Identify the error code
and description.
No
Is the error
hardware
related?
Start
Yes
Refer to page C-3 for
probable cause and
recommended action.
Are the wire
connections
tight?
No
Tighten wire
connections.
No
Does the
controller have
power supplied?
Yes
Clear fault.
Is the Power
LED on?
Is the RUN LED
on?
Refer to page C-3 for
probable cause and
recommended action.
No
Yes
Return controller to RUN
or any of the REM test
modes.
Is the Fault LED
on?
Yes
Refer to page C-3 for
probable cause and
recommended action.
Test and verify system
operation.
C-4
Check power.
Yes
Yes
Correct the condition
causing the fault.
No
No
Is an input LED
accurately showing
status?
No
Yes
Refer to page C-3 for
probable cause and
recommended action.
Troubleshooting Your System
Identifying Controller Faults
While a program is executing, a fault may occur within the operating system or your
program. When a fault occurs, you have various options to determine what the fault is
and how to correct it. This section describes how to clear faults and provides a list of
possible advisory messages with recommended corrective actions.
Automatically Clearing Faults
You can automatically clear a fault by cycling power to the controller when the Fault
Override at Powerup bit (S:1/8) is set in the status file.
You can also configure the controller to clear faults and go to RUN every time the
controller is power cycled. This is a feature that OEMs can build into their equipment
to allow end users to reset the controller. If the controller faults, it can be reset by
simply cycling power to the machine. To accomplish this, set the following bits in the
status file:
•
S2:1/8 - Fault Override at Power-up
•
S2:1/12 - Mode Behavior
If the fault condition still exists after cycling power, the controller re-enters the fault
mode. For more information on status bits, see “System Status File” on page G-1.
Note:
You can declare your own application-specific major fault by writing
your own unique value to S:6 and then setting bit S:1/13 to prevent
reusing system defined codes. The recommended values for user defined
faults are FF00 to FF0F.
Manually Clearing Faults Using the Fault Routine
The occurrence of recoverable or non-recoverable user faults can cause the user fault
subroutine to be executed. If the fault is recoverable, the subroutine can be used to
correct the problem and clear the fault bit S:1/13. The controller then continues in the
Run or test mode.
The subroutine does not execute for non-user faults. See “User Fault Routine” on
page 23-6 for information on creating a user fault subroutine.
C-5
MicroLogix 1500 Programmable Controllers User Manual
Fault Messages
This section contains fault messages that can occur during operation of the
MicroLogix 1500 programmable controllers. Each table lists the error code
description, the probable cause, and the recommended corrective action.
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
• Re-download or transfer the
program.
• Verify battery is connected.
• Contact your local Allen-Bradley
representative if the error persists.
0001
NVRAM ERROR
The default program is loaded to the
controller memory. This occurs:
• if a power down occurred during
program download or transfer from the
memory module.
• RAM integrity test failed.
0002
UNEXPECTED
RESET
The controller was unexpectedly reset due • Refer to proper grounding
to a noisy environment or internal hardware
guidelines in chapter 2 and using
failure. The default program is loaded.
surge suppressors in chapter 1.
• Verify battery is connected.
• Contact your local Allen-Bradley
representative if the error persists.
0003
MEMORY
MODULE USER
PROGRAM IS
CORRUPT
Memory module memory error. This error
can also occur when going to the Run
mode.
Re-program the memory module. If
the error persists, replace the
memory module.
0004
MEMORY
INTEGRITY
ERROR
While the controller was powered up, ROM
or RAM became corrupt.
• Cycle power on your unit. Then,
re-download your program and
start up your system.
• Refer to proper grounding
guidelines in chapter 2 and using
surge suppressors in chapter 1.
• Contact your local Allen-Bradley
representative if the error persists.
0006
MEMORY
MODULE
HARDWARE
FAULT
The memory module hardware faulted or
the memory module is incompatible with
OS.
• Upgrade the OS to be compatible
with memory module.
• Obtain a new memory module.
C-6
Troubleshooting Your System
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
0007
MEMORY
MODULE
TRANSFER
ERROR
Failure during memory module transfer.
Re-attempt the transfer. If the error
persists, replace the memory module.
0008
FATAL INTERNAL
SOFTWARE
ERROR
An unexpected software error occurred.
• Cycle power on your unit. Then,
re-download your program and reinitialize any necessary data.
• Start up your system.
• Refer to proper grounding
guidelines in chapter 2 and using
surge suppressors in chapter 1.
• Contact your local Allen-Bradley
representative if the error persists.
0009
FATAL INTERNAL
HARDWARE
ERROR
An unexpected hardware error occurred.
• Cycle power on your unit. Then,
re-download your program and reinitialize any necessary data.
• Start up your system.
• Refer to proper grounding
guidelines in chapter 2 and using
surge suppressors in chapter 1.
• Contact your local Allen-Bradley
representative if the error persists.
000A
OS MISSING OR
CORRUPT
The operating system required for the user
program is corrupt or missing.
• Download a new OS using
ControlFlash.
• Contact your local Allen-Bradley
representative for more
information about available
operating systems for the
MicroLogix 1500 controller.
C-7
MicroLogix 1500 Programmable Controllers User Manual
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
000B
BASE HARDWARE The base hardware faulted or is
FAULT
incompatible with the OS.
0012
LADDER
PROGRAM
ERROR
The ladder program has a memory integrity
problem.
• Reload the program or re-compile
and reload the program. If the
error persists, be sure to use RSI
programming software to develop
and load the program.
• Refer to proper grounding
guidelines in chapter 2 and using
surge suppressors in chapter 1.
0015
I/O
CONFIGURATION
FILE ERROR
The user program I/O configuration is
invalid.
Re-compile and reload the program,
and enter the Run mode. If the error
persists, be sure to use RSI
programming software to develop and
load the program.
0016
STARTUP
PROTECTION
FAULT
The user fault routine was executed at
power-up, prior to the main ladder program.
Bit S:1/13 (Major Error Halted) was not
cleared at the end of the User Fault
Routine. The User Fault Routine ran
because bit S:1/9 was set at power-up.
• Either reset bit S:1/9 if this is
consistent with the application
requirements, and change the
mode back to RUN, or
• clear S:1/13, the Major Error
Halted bit, before the end of the
User Fault Routine.
0017
NVRAM/MEMORY
MODULE ERROR
Bit S:2/9 is set in the controller and the
memory module user program does not
match the controller user program.
Transfer the memory module program
to the controller and then change to
Run mode.
C-8
• Upgrade the OS using
ControlFlash to be compatible with
the base.
• Obtain a new base.
• Contact your local Allen-Bradley
representative for more
information about available
operating systems for the
MicroLogix 1500 controller.
Troubleshooting Your System
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
0018
MEMORY
MODULE USER
PROGRAM
INCOMPATIBLE
WITH OS
The user program in the memory module is
incompatible with the OS.
• Upgrade the OS using
ControlFlash to be compatible with
the memory module.
• Obtain a new memory module.
• Contact your local Allen-Bradley
representative for more
information about available
operating systems for the
MicroLogix 1500 controller.
001A
USER PROGRAM
INCOMPATIBLE
WITH OS AT
POWERUP
The user program in the controller is
incompatible with the OS.
• Upgrade the OS using
ControlFlash to be compatible with
the user program in the controller.
• Re-compile and reload the
program.
0020
MINOR ERROR AT A minor fault bit (bits 0-7) in S:5 was set at
END OF SCAN
the end of scan.
DETECTED
0022
WATCHDOG
TIMER EXPIRED,
SEE S:3
The program scan time exceeded the
watchdog timeout value (S:3H).
• Determine if the program is caught
in a loop and correct the problem.
• Increase the watchdog timeout
value in the status file.
0023
STI ERROR
An error occurred in the STI configuration.
See the Error Code in the STI
Function File for the specific error.
0028
INVALID OR
NONEXISTENT
USER FAULT
ROUTINE VALUE
• A fault routine number was entered in
the status file, number (S:29), but either
the fault routine was not physically
created, or
• the fault routine number was less than 3
or greater than 255.
• Either clear the fault routine file
number (S:29) in the status file, or
• create a fault routine for the file
number reference in the status file
(S:29). The file number must be
greater than 2 and less than 256.
• Correct the instruction logic
causing the error.
• Enter the status file display in your
programming software and clear
the fault.
• Enter the Run mode.
C-9
MicroLogix 1500 Programmable Controllers User Manual
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
0029
INSTRUCTION
INDIRECTION
OUTSIDE OF
DATA SPACE
An indirect address reference in the ladder
program is outside of the entire data file
space.
Correct the program to ensure that
there are no indirect references
outside data file space.
Re-compile, reload the program and
enter the Run mode.
002E
EII ERROR
An error occurred in the EII configuration.
See the Error Code in the EII
Function File for the specific error.
0030
SUBROUTINE
NESTING
EXCEEDS LIMIT
The JSR instruction nesting level exceeded
the controller memory space.
Correct the user program to reduce
the nesting levels used and to meet
the restrictions for the JSR
instruction. Then reload the program
and Run.
0031
UNSUPPORTED
INSTRUCTION
DETECTED
The program contains an instruction(s) that
is not supported by the controller.
• Modify the program so that all
instructions are supported by the
controller.
• Re-compile and reload the
program and enter the Run mode.
0032
SQO/SQC/SQL
OUTSIDE OF
DATA FILE SPACE
A sequencer instruction length/position
parameter references outside of the entire
data file space.
• Correct the program to ensure that
the length and position
parameters do not point outside
data file space.
• Re-compile, reload the program
and enter the Run mode.
0033
BSL/BSR/FFL/
FFU/LFL/LFU
CROSSED DATA
FILE SPACE
The length/position parameter of a BSL,
BSR, FFL, FFU, LFL, or LFU instruction
references outside of the entire data file
space.
• Correct the program to ensure that
the length and position
parameters do not point outside of
the data space.
• Re-compile, reload the program
and enter the Run mode.
0034
NEGATIVE VALUE A negative value was loaded to a timer
IN TIMER PRESET preset or accumulator.
OR
ACCUMULATOR
C-10
• If the program is moving values to
the accumulated or preset word of
a timer, make certain these values
are not negative.
• Reload the program and enter the
Run mode.
Troubleshooting Your System
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
0035
ILLEGAL
INSTRUCTION IN
INTERRUPT FILE
The program contains a Temporary End
(TND), Refresh (REF), or Service
Communication instruction in an interrupt
subroutine (STI, EII, HSC) or user fault
routine.
• Correct the program.
• Re-compile, reload the program
and enter the Run mode.
0036
INVALID PID
PARAMETER
An invalid value is being used for a PID
instruction parameter.
See page 24-1, Process Control
Instruction for more information about
the PID instruction.
0037
HSC ERROR
An error occurred in the HSC configuration.
See the Error Code in the HSC
Function File for the specific error.
003B
PTO ERROR
An error occurred in the PTO instruction
configuration.
See the Error Code in the PTO
Function File for the specific error.
003C
PWM ERROR
An error occurred in the PWM instruction
configuration.
See the Error Code in the PWM
Function File for the specific error.
003D
INVALID
SEQUENCER
LENGTH/
POSITION
A sequencer instruction (SQO, SQC, SQL)
length/position parameter is greater than
255.
Correct the user program, then recompile, reload the program and
enter the Run mode.
003E
INVALID BIT
A BSR or BSL instruction length parameter
SHIFT OR LIFO/
is greater than 2048) or
FIFO PARAMETER A FFU, FFL, LFU, LFL instruction length
parameter is greater than 128 (word file) or
greater than 64 (double word file)
003F
COP/FLL
OUTSIDE OF
DATA FILE SPACE
A COP or FLL instruction length parameter • Correct the program to ensure that
references outside of the entire data space.
the length and parameter do not
point outside of the data file space.
• Re-compile, reload the program
and enter the Run mode.
0050
CONTROLLER
TYPE MISMATCH
A particular controller type was selected in
the user program configuration, but did not
match the actual controller type.
• Correct the controller base type, or
• Reconfigure the program to match
the attached controller type.
0051
BASE TYPE
MISMATCH
A particular base type (AWA, BWA, BXB)
was selected in the user program
configuration, but did no match the actual
base.
• Correct the base type, or
• Reconfigure the program to match
the attached base.
Correct the user program or allocate
more data file space using the
memory map, then reload and Run.
C-11
MicroLogix 1500 Programmable Controllers User Manual
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
0052
MINIMUM SERIES
ERROR
The base minimum series selected in the
user program configuration was greater
than the series on the actual base.
• Correct the base type, or
• Reconfigure the program to match
the attached base.
0070
EXPANSION I/O
TERMINATOR
REMOVED
The required expansion I/O terminator was
removed.
• Check the expansion I/O
terminator on the last I/O module.
• Cycle power.
xx711
EXPANSION I/O
HARDWARE
ERROR
The controller cannot communicate with an
expansion I/O module.
• Check connections.
• Check for a noise problem and be
sure proper grounding practices
are used.
• Replace the module.
• Cycle power.
xx791
EXPANSION I/O
MODULE ERROR
An expansion I/O module generated an
error.
• Refer to the I/O Module Status
(IOS) file.
• Consult 1769 publications for
specific module to determine
possible causes of a module error.
0080
EXPANSION I/O
TERMINATOR
REMOVED
The required expansion I/O terminator was
removed.
• Check expansion I/O terminator
on last I/O module.
• Cycle power.
xx811
EXPANSION I/O
HARDWARE
ERROR
The controller cannot communicate with an
expansion I/O module.
• Check connections.
• Check for a noise problem and be
sure proper grounding practices
are used.
• Replace the module.
• Cycle power.
0083
MAX I/O CABLES
EXCEEDED
The maximum number of expansion I/O
cables allowed was exceeded.
• Reconfigure the expansion I/O
system so that it has an allowable
number of cables.
• Cycle power.
0084
MAX I/O POWER
SUPPLIES
EXCEEDED
The maximum number of expansion I/O
power supplies allowed was exceeded.
• Reconfigure the expansion I/O
system so that it has the correct
number of power supplies.
C-12
Troubleshooting Your System
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
0085
MAX I/O
MODULES
EXCEEDED
The maximum number of expansion I/O
modules allowed was exceeded.
• Reconfigure the expansion I/O
system so that it has an allowable
number of modules.
• Cycle power.
xx861
EXPANSION I/O
MODULE BAUD
RATE ERROR
An expansion I/O module could not
communicate at the baud rate specified in
the user program I/O configuration.
• Change the baud rate in the user
program I/O configuration, and
• re-compile, reload the program
and enter the Run mode, or
• replace the module.
• Cycle power.
xx871
I/O
CONFIGURATION
MISMATCH
• The expansion I/O configuration in the
user program did not match the actual
configuration, or
• The expansion I/O configuration in the
user program specified a module, but
one was not found, or
• The expansion I/O module configuration
data size for a module was greater than
what the module is capable of holding.
• Either correct the user program
I/O configuration to match the
actual configuration, or
• With power off, correct the actual
I/O configuration to match the user
program configuration.
xx881
EXPANSION I/O
MODULE
CONFIGURATION
ERROR
The number of input or output image words • Correct the user program I/O
configured in the user program exceeds the
configuration to reduce the
image size in the expansion I/O module.
number of input or output words,
and
• re-compile, reload the program
and enter the Run mode.
xx891
EXPANSION I/O
MODULE ERROR
An expansion I/O module generated an
error.
• Refer to the I/O status file.
• Consult 1769 publications for
specific module to determine
possible causes of a module error.
xx8A1
EXPANSION I/O
CABLE
CONFIGURATION
MISMATCH
ERROR
• Either an expansion I/O cable is
configured in the user program, but no
cable is present, or
• an expansion I/O cable is configured in
the user program and a cable is
physically present, but the types do not
match.
• Correct the user program to
eliminate a cable that is not
present
• re-compile, reload the program
and enter the Run mode, or
• add the missing cable.
• Cycle power.
1. xx indicates module number. If xx = 0, problem cannot be traced to a specific module.
C-13
MicroLogix 1500 Programmable Controllers User Manual
Error
Code
(Hex)
Advisory
Message
Description
Recommended Action
xx8B1
EXPANSION I/O
POWER SUPPLY
CONFIGURATION
MISMATCH
ERROR
• Either an expansion I/O power supply is
configured in the user program, but no
power supply is present, or
• an expansion I/O power supply is
configured in the user program and a
power supply is physically present, but
the types do not match.
• Correct the user program to
eliminate a power supply that is
not present
• re-compile, reload the program
and enter the Run mode, or
• With power removed, add the
missing power supply.
xx8C1
EXPANSION I/O
OBJECT TYPE
MISMATCH
An expansion I/O object (i.e. cable, power • Correct the user program I/O
supply, or module) in the user program I/O
configuration so that the object
configuration is not the same object type as
types match the actual
is physically present.
configuration, and
• Re-compile, reload the program
and enter the Run mode. Or
• Correct the actual configuration to
match the user program I/O
configuration.
• Cycle power.
1. xx indicates module number. If xx = 0, problem cannot be traced to a specific module.
Calling Allen-Bradley for Assistance
If you need to contact Allen-Bradley or local distributor for assistance, it is helpful to
obtain the following (prior to calling):
•
controller type, series letter, and revision letter of the base unit
•
series letter, revision letter, and firmware (FRN) number of the processor (on
bottom side of processor unit)
•
controller LED status
•
controller error codes (found in S2:6 of status file).
1. xx indicates module number. If xx = 0, problem cannot be traced to a specific module.
C-14
Understanding the Communication Protocols
D
Understanding the
Communication Protocols
Use the information in this appendix to understand the differences in communication
protocols. The following protocols are supported from the RS-232 communication
channel:
•
DF1 Full-Duplex
•
DF1 Half-Duplex Slave
•
DH485
See “Connecting the System” on page 4-1 for information about required network
devices and accessories.
RS-232 Communication Interface
The communications port on the MicroLogix 1500 utilizes an RS-232 connector. RS232 is an Electronics Industries Association (EIA) standard that specifies the
electrical, mechanical, and functional characteristics for serial binary communication.
It provides you with a variety of system configuration possibilities. (RS-232 is a
definition of electrical characteristics; it is not a protocol.)
One of the biggest benefits of the RS-232 interface is that it lets you integrate
telephone and radio modems into your control system (using the appropriate DF1
protocol only; not DH485 protocol).
D-1
MicroLogix 1500 Programmable Controllers User Manual
DF1 Full-Duplex Protocol
DF1 Full-Duplex protocol provides a point-to-point connection between two devices.
DF1 Full-Duplex protocol combines data transparency (American National Standards
Institute ANSI - X3.28-1976 specification subcategory D1) and 2-way simultaneous
transmission with embedded responses (subcategory F1).
The MicroLogix 1500 controllers support the DF1 Full-Duplex protocol via RS-232
connection to external devices, such as computers, or other controllers that support
DF1 Full-Duplex.
DF1 is an open protocol. Refer to DF1 Protocol and Command Set Reference
Manual, Allen-Bradley publication 1770-6.5.16, for more information.
DF1 Full-Duplex Operation
DF1 Full-Duplex protocol (also referred to as DF1 point-to-point protocol) is useful
where RS-232 point-to-point communication is required. This type of protocol
supports simultaneous transmissions between two devices in both directions. DF1
protocol controls message flow, detects and signals errors, and retries if errors are
detected.
When the system driver is DF1 Full-Duplex, the following parameters can be
changed:
Table 25-1: DF1 Full-Duplex Configuration Parameters
Parameter
Options
Baud Rate
300, 600, 1200, 2400, 4800, 9600, 19.2K, 38.4K
Parity
none, even
Source ID (Node Address)
0 to 254 decimal
Control Line
no handshaking, Full-Duplex modem handshaking
Error Detection
CRC, BCC
Embedded Responses
auto-detect, enabled
Duplicate Packet (Message) Detect
enabled, disabled
ACK Timeout
1 to 65535 counts (20 ms increments)
NAK retries
0 to 255
ENQ retries
0 to 255
Stop Bits
not a setting, always 1
D-2
Default
19.2K
none
1
no handshaking
CRC
auto detect
enabled
50 counts
3 retries
3 retries
1
Understanding the Communication Protocols
Example DF1 Full-Duplex Connections
For information about required network connecting equipment, see chapter 3,
Connecting the System.
Optical Isolator (recommended)
1761-CBL-PM02
Personal Computer
Modem cable
Personal Computer
Modem
Optical Isolator
(recommended)
Modem
Micro Controller
1761-CBL-PM02
We recommend using an AIC+, catalog number 1761-NET-AIC, as your optical
isolator.
D-3
MicroLogix 1500 Programmable Controllers User Manual
DF1 Half-Duplex Protocol
DF1 Half-Duplex protocol provides a multi-drop single master/multiple slave
network. DF1 Half-Duplex protocol supports data transparency (American National
Standards Institute ANSI - X3.28-1976 specification subcategory D1). In contrast to
DF1 Full-Duplex, communication takes place in one direction at a time. You can use
the RS-232 port on the MicroLogix 1500 as both a Half-Duplex programming port,
and a Half-Duplex peer-to-peer messaging port.
DF1 Half-Duplex Operation
The master device initiates all communication by “polling” each slave device. The
slave device may only transmit message packets when it is polled by the master. It is
the master’s responsibility to poll each slave on a regular and sequential basis to allow
slave devices an opportunity to communicate. During a polling sequence, the master
polls a slave either repeatedly until the slave indicates that it has no more message
packets to transmit or just one time per polling sequence, depending on how the
master is configured.
An additional feature of the DF1 Half-Duplex protocol is that it is possible for a slave
device to enable a MSG instruction in its ladder program to send or request data to/
from another slave. When the initiating slave is polled, the MSG instruction is sent to
the master. The master recognizes that the message is not intended for it, but for
another slave, so the master immediately forwards the message to the intended slave.
This slave-to-slave transfer is a function of the master device and is also used by
programming software to upload and download programs to processors on the DF1
Half-Duplex link.
The MicroLogix 1500 can only act as a slave device. A device that can act as a master
is required. Several Allen-Bradley products support DF1 Half-Duplex master
protocol. They include the SLC 5/03™ and higher, and enhanced PLC-5® processors.
Rockwell Software WINtelligent LINX™ and RSLinx (version 2.x and higher) also
support DF1 Half-Duplex master protocol.
DF1 Half-Duplex supports up to 255 devices (address 0 to 254) with address 255
reserved for master broadcasts. The MicroLogix 1500 supports broadcast reception
but cannot initiate a broadcast command. The MicroLogix 1500 supports HalfDuplex modems using RTS/CTS hardware handshaking.
D-4
Understanding the Communication Protocols
When the system driver is DF1 Half-Duplex Slave, the following parameters can be
changed:
Table 25-2: DF1 Half-Duplex Configuration Parameters
Parameter
Options
Baud Rate
300, 600, 1200, 2400, 4800, 9600, 19.2K, 38.4K
Parity
none, even
Source ID (Node
0 to 254 decimal
Address)
Control Line
no handshaking, Half-Duplex modem handshaking
Error Detection
EOT Suppression
CRC, BCC
enabled, disabled
When EOT Suppression is enabled, the slave does not respond when polled if no message
is queued. This saves modem transmission power when there is no message to transmit.
Duplicate Packet
enabled, disabled
(Message) Detect
Detects and eliminates duplicate responses to a message. Duplicate packets may be sent
under noisy communication conditions if the sender’s Message Retries are not set to 0.
Poll Timeout (x20 ms) 0 to 65535 (can be set in 20 ms increments)
Poll Timeout only applies when a slave device initiates a MSG instruction. It is the amount
of time that the slave device waits for a poll from the master device. If the slave device does
not receive a poll within the Poll Timeout, a MSG instruction error is generated, and the
ladder program needs to requeue the MSG instruction. If you are using a MSG instruction,
it is recommended that a Poll Timeout value of zero not be used. Poll Timeout is disabled
when set to zero.
RTS Off Delay (x20
0 to 65535 (can be set in 20 ms increments)
ms)
Specifies the delay time between when the last serial character is sent to the modem and
when RTS is deactivated. Gives the modem extra time to transmit the last character of a
packet.
RTS Send Delay (x20 0 to 65535 (can be set in 20 ms increments)
ms)
Specifies the time delay between setting RTS until checking for the CTS response. For use
with modems that are not ready to respond with CTS immediately upon receipt of RTS.
Message Retries
0 to 255
Specifies the number of times a slave device attempts to resend a message packet when it
does not receive an ACK from the master device. For use in noisy environments where
message packets may become corrupted in transmission.
Pre Transmit Delay
0 to 65535 (can be set in 1 ms increments)
(x1 ms)
• When the Control Line is set to no handshaking, this is the delay time before
transmission. Required for 1761-NET-AIC physical Half-Duplex networks. The 1761NET-AIC needs delay time to change from transmit to receive mode.
• When the Control Line is set to DF1 Half-Duplex Modem, this is the minimum time delay
between receiving the last character of a packet and the RTS assertion.
Default
1200
none
1
no
handshaking
CRC
disabled
enabled
50
0
0
3
0
D-5
MicroLogix 1500 Programmable Controllers User Manual
RS-232 (DF1 Protocol)
SLC 5/03 Processor
Modular Controller
MicroLogix 1500
Programmable
Controller
Note:
Rockwell Software WINtelligent LINX,
RSLinx 2.0 (or higher), SLC 5/03, SLC
5/04, and SLC 5/05, or PLC-5
processors configured for DF1 HalfDuplex Master.
MicroLogix 1500
Programmable Controllers
SLC 500 Fixed I/O
Controller with 1747-KE
Interface Module
It is recommended that isolation (1761-NET-AIC) be provided between the
MicroLogix 1500 and the modem.
Considerations When Communicating as a DF1 Slave on a Multi-drop Link
When communication is between either your programming software and a
MicroLogix 1500 Programmable Controller or between two MicroLogix 1500
Programmable Controllers via a slave-to-slave connection on a larger multi-drop link,
the devices depend on a DF1 Master to give each of them polling permission to
transmit in a timely manner. As the number of slaves increases on the link (up to 254),
the time between when your programming software or the MicroLogix 1500
Controller is polled also increases. This increase in time may become larger if you are
using low baud rates.
As these time periods grow, the following values may need to be changed to avoid
loss of communication:
D-6
•
programming software: increase poll timeout and reply timeout values
•
MicroLogix 1500 Programmable Controller: increase poll timeout
Understanding the Communication Protocols
Ownership Timeout
When a program download sequence is started by a software package to download a
ladder logic program to a MicroLogix 1500 controller, the software takes “program
ownership” of the processor. Program ownership prevents other devices from reading
from or writing to the processor while the download is in process. Once the download
is completed, the programming software returns the program ownership to the
controller, so other devices can communicate with it again.
The controller clears the program ownership if no supported commands are received
from the owner within the timeout period. If the program ownership were not cleared
after a download sequence interruption, the processor would not accept commands
from any other device because it would assume another device still had program
ownership.
Important:
If a download sequence is interrupted, due to electromagnetic
interference or other events, discontinue communications to the
controller for the ownership timeout period and then restart the
program download. The ownership timeout period is 60 seconds.
After the timeout, you can re-establish communications with the
processor and try the program download again. The only other
way to remove program ownership is to cycle power on the
processor.
D-7
MicroLogix 1500 Programmable Controllers User Manual
Using Modems with MicroLogix 1500 Programmable Controllers
The types of modems that you can use with MicroLogix 1500 controllers include dialup phone modems, leased-line modems, radio modems and line drivers.
For point-to-point Full-Duplex modem connections that do not require any modem
handshaking signals to operate, use DF1 Full-Duplex protocol. For point-to-point
Full-Duplex modem connections that require RTS/CTS handshaking, use DF1 FullDuplex protocol.
For multi-drop modem connections, or for point-to-point modem connections that
require RTS/CTS handshaking, use DF1 Half-Duplex slave protocol. In this case, one
(and only one) of the other devices must be configured for DF1 Half-Duplex master
protocol.
Important:
Note:
Never attempt to use DH485 protocol through modems under any
circumstance.
All MicroLogix 1500 controllers support RTS/CTS modem handshaking
when configured for DF1 Full-Duplex protocol with the control line
parameter set to Full-Duplex Modem Handshaking or DF1 Half-Duplex
slave protocol with the control line parameter set to “Half-Duplex Modem”.
No other modem handshaking lines (i.e. Data Set Ready, Carrier Detect and
Data Terminal Ready) are supported by any MicroLogix 1500 controllers.
Dial-Up Phone Modems
Dial-up phone line modems support point-to-point Full-Duplex communications.
Normally a MicroLogix 1500 controller, on the receiving end of the dial-up
connection, will be configured for DF1 Full-Duplex protocol with the control line
parameter set for Full-Duplex modem. The modem connected to the MicroLogix
1500 controller must support auto-answer. The MicroLogix 1500 has no means to
cause its modem to initiate or disconnect a phone call, so this must be done from the
site of the remote modem.
D-8
Understanding the Communication Protocols
Leased-Line Modems
Leased-line modems are used with dedicated phone lines that are typically leased
from the local phone company. The dedicated lines may be in a point-to-point
topology supporting Full-Duplex communications between two modems or in a
multi-drop topology supporting Half-Duplex communications between three or more
modems. In the point-to-point topology, configure the MicroLogix 1500 controllers
for DF1 Full-Duplex protocol. In the multi-drop topology, configure the MicroLogix
1500 controllers for DF1 Half-Duplex slave protocol with the control line parameter
set to “Half-Duplex Modem”.
Radio Modems
Radio modems may be implemented in a point-to-point topology supporting either
Half-Duplex or Full-Duplex communications, or in a multi-drop topology supporting
Half-Duplex communications between three or more modems. In the point-to-point
topology using Full-Duplex radio modems, configure the MicroLogix 1500
controllers for DF1 Full-Duplex protocol. In the point-to-point topology using HalfDuplex radio modems, or multi-drop topology using Half-Duplex radio modems,
configure the MicroLogix 1500 controllers for DF1 Half-Duplex slave protocol. If
these radio modems require RTS/CTS handshaking, configure the control line
parameter to “Half-Duplex Modem”.
Line Drivers
Line drivers, also called short-haul “modems”, do not actually modulate the serial
data, but rather condition the electrical signals to operate reliably over long
transmission distances (up to several miles). Allen-Bradley’s AIC+ Advanced
Interface Converter is a line driver that converts an RS-232 electrical signal into an
RS485 electrical signal, increasing the signal transmission distance from 50 to 4000
feet.
In a point-to-point line driver topology, configure the MicroLogix 1500 controller for
DF1 Full-Duplex protocol. In a multi-drop line driver topology, configure the
MicroLogix 1500 controllers for DF1 Half-Duplex slave protocol. If the line drivers
that are used require RTS/CTS handshaking, configure the Control Line parameter to
Half-Duplex Modem.
D-9
MicroLogix 1500 Programmable Controllers User Manual
DH485 Communication Protocol
The information in this section describes the DH485 network functions, network
architecture, and performance characteristics. It will also help you plan and operate
the MicroLogix 1500 on a DH485 network.
DH485 Network Description
The DH485 protocol defines the communication between multiple devices that
coexist on a single pair of wires. DH485 protocol uses RS-485 Half-Duplex as its
physical interface. (RS-485 is a definition of electrical characteristics; it is not a
protocol.) RS-485 uses devices that are capable of co-existing on a common data
circuit, thus allowing data to be easily shared between devices.
The DH485 network offers:
•
interconnection of 32 devices
•
multi-master capability
•
token passing access control
•
the ability to add or remove nodes without disrupting the network
•
maximum network length of 1219 m (4000 ft)
The DH485 protocol supports two classes of devices: initiators and responders. All
initiators on the network get a chance to initiate message transfers. To determine
which initiator has the right to transmit, a token passing algorithm is used.
The following section describes the protocol used to control message transfers on the
DH485 network.
DH485 Token Rotation
A node holding the token can send a message onto the network. Each node is allowed
a fixed number of transmissions (based on the Token Hold Factor) each time it
receives the token. After a node sends a message, it passes the token to the next
device.
The allowable range of node addresses 0 to 31. There must be at least one initiator on
the network (such as a MicroLogix 1000 or 1500 controller, or an SLC 5/02™ or
higher processor).
D-10
Understanding the Communication Protocols
DH485 Configuration Parameters
When the MicroLogix 1500 communications are configured for DH485, the
following parameters can be changed:
Table 25-3: DF1 Full-Duplex Configuration Parameters
Parameter
Options
Baud Rate
9600, 19.2K
Node Address
1 to 31 decimal
Token Hold Factor
1 to 4
Max Node Address
1 to 31
Default
19.2K
1
2
31
See “Software Considerations” on page D-15 for tips on setting the parameters listed
above.
Devices that use the DH485 Network
In addition to the MicroLogix 1500 controllers, the devices shown in the following
table also support the DH485 network.
Table 25-4: Allen-Bradley Devices that Support DH485 Communication
Catalog Number
Bulletin 1761
Controllers
Bulletin 1747
Processors
1746-BAS
Description
MicroLogix 1000
Installation
Series C or
later
SLC 500 Processors SLC Chassis
BASIC Module
SLC Chassis
1785-KA5
DH+TM/DH485
Gateway
(1771) PLC
Chassis
2760-RB
Flexible Interface
Module
(1771) PLC
Chassis
Function
These controllers support DH485 communications.
Publication
1761-6.3
These processors support a variety of I/O
requirements and functionality.
Provides an interface for SLC 500 devices to foreign
devices. Program in BASIC to interface the 3 channels
(2 RS232 and 1 DH485) to printers, modems, or the
DH485 network for data collection.
Provides communication between stations on the PLC5U (DH+) and SLC 500 (DH485) networks. Enables
communication and data transfer from PLC® to SLC
500 on DH485 network. Also enables programming
software programming or data acquisition across DH+
to DH485.
Provides an interface for SLC 500 (using protocol
cartridge 2760-SFC3) to other A-B PLCs and devices.
Three configurable channels are available to interface
with Bar Code, Vision, RF, Dataliner™ , and PLC
systems.
1747-6.2
1746-6.1
1746-6.2
1746-6.3
1785-6.5.5
1785-1.21
2760-ND001
D-11
MicroLogix 1500 Programmable Controllers User Manual
Table 25-4: Allen-Bradley Devices that Support DH485 Communication
Catalog Number
1784-KTX, -KTXD
1784-PCMK
1747-PT1
Description
PC DH485 IM
Installation
Function
IBM XT/AT
Provides DH485 using RSLinx
Computer Bus
PCMCIA IM
PCMCIA slot Provides DH485 using RSLinx
in computer
and
Interchange
Hand-Held Terminal NA
Provides hand-held programming, monitoring,
configuring, and troubleshooting capabilities for SLC
500 processors.
DTAM, DTAM Plus, Panel Mount Provides electronic operator interface for SLC 500
and DTAM Micro
processors.
Operator Interfaces
1747-DTAM,
2707-L8P1, -L8P2,
-L40P1, -L40P2,
-V40P1, -V40P2, V40P2N, -M232P3,
and -M485P3
2711-K5A2, -B5A2, PanelView 550 and
-K5A5, -B5A5,
PanelView 900
-K5A1, -B5A1,
Operator Terminals
-K9A2, -T9A2,
-K9A5, -T9A5,
-K9A1, and -T9A1
Panel Mount
NA = Not Applicable
D-12
Provides electronic operator interface for SLC 500
processors.
Publication
1784-6.5.22
1784-6.5.19
1747-NP002
1747-ND013
2707-800,
2707-803
2711-802,
2711-816
Understanding the Communication Protocols
Important DH485 Network Planning Considerations
Carefully plan your network configuration before installing any hardware. Listed
below are some of the factors that can affect system performance:
•
amount of electrical noise, temperature, and humidity in the network environment
•
number of devices on the network
•
connection and grounding quality in installation
•
amount of communication traffic on the network
•
type of process being controlled
•
network configuration
The major hardware and software issues you need to resolve before installing a
network are discussed in the following sections.
Hardware Considerations
You need to decide the length of the communication cable, where you route it, and
how to protect it from the environment where it will be installed.
When the communication cable is installed, you need to know how many devices are
to be connected during installation and how many devices will be added in the future.
The following sections will help you understand and plan the network.
Number of Devices and Length of Communication Cable
The maximum length of the communication cable is 1219 m (4000 ft). This is the
total cable distance from the first node to the last node on the network.
Planning Cable Routes
Follow these guidelines to help protect the communication cable from electrical
interference:
•
Keep the communication cable at least 1.52 m (5 ft) from any electric motors,
transformers, rectifiers, generators, arc welders, induction furnaces, or sources of
microwave radiation.
•
If you must run the cable across power feed lines, run the cable at right angles to
the lines.
D-13
MicroLogix 1500 Programmable Controllers User Manual
•
If you do not run the cable through a contiguous metallic wireway or conduit,
keep the communication cable at least 0.15 m (6 in.) from ac power lines of less
than 20A, 0.30 m (1 ft) from lines greater than 20A, but only up to 100k VA, and
0.60 m (2 ft) from lines of 100k VA or more.
•
If you run the cable through a contiguous metallic wireway or conduit, keep the
communication cable at least 0.08 m (3 in.) from ac power lines of less than 20A,
0.15 m (6 in.) from lines greater than 20A, but only up to 100k VA, and 0.30 m (1
ft) from lines of 100k VA or more.
Running the communication cable through conduit provides extra protection from
physical damage and electrical interference. If you route the cable through
conduit, follow these additional recommendations:
v Use ferromagnetic conduit near critical sources of electrical interference.
You
can use aluminum conduit in non-critical areas.
v Use plastic connectors to couple between aluminum and ferromagnetic conduit.
Make an electrical connection around the plastic connector (use pipe clamps
and the heavy gauge wire or wire braid) to hold both sections at the same
potential.
v Ground the entire length of conduit by attaching it to the building earth ground.
v Do not let the conduit touch the plug on the cable.
v Arrange the cables loosely within the conduit. The conduit should contain only
serial communication cables.
v Install the conduit so that it meets all applicable codes and environmental
specifications.
For more information on planning cable routes, see Industrial Automation Wiring and
Grounding Guidelines, Publication Number 1770-4.1.
D-14
Understanding the Communication Protocols
Software Considerations
Software considerations include the configuration of the network and the parameters
that can be set to the specific requirements of the network. The following are major
configuration factors that have a significant effect on network performance:
•
number of nodes on the network
•
addresses of those nodes
•
baud rate
The following sections explain network considerations and describe ways to select
parameters for optimum network performance (speed). See your programming
software’s user manual for more information.
Number of Nodes
The number of nodes on the network directly affects the data transfer time between
nodes. Unnecessary nodes (such as a second programming terminal that is not being
used) slow the data transfer rate. The maximum number of nodes on the network is
32.
Setting Node Addresses
The best network performance occurs when node addresses are assigned in sequential
order. Initiators, such as personal computers, should be assigned the lowest
numbered addresses to minimize the time required to initialize the network. The valid
range for the MicroLogix 1500 controllers is 1-31 (controllers cannot be node 0). The
default setting is 1. The node address is stored in the controller Communications
Status file (CS0:5/0 to CS0:5/7).
Setting Controller Baud Rate
The best network performance occurs at the highest baud rate, which is 19200. This is
the default baud rate for a MicroLogix 1500 device on the DH485 network. All
devices must be at the same baud rate. This rate is stored in the controller
Communications Status file (CS0:5/8 to CS0:5/15).
D-15
MicroLogix 1500 Programmable Controllers User Manual
Setting Maximum Node Address
Once you have an established network set up, and are confident that you will not be
adding more devices, you may enhance performance by adjusting the maximum node
address of your controllers. It should be set to the highest node address being used.
Important:
All devices should be set to the same maximum node address.
Example DH485 Connections
The following network diagrams provide examples of how to connect MicroLogix
1500 controllers to the DH485 network using the Advanced Interface Converter
(AIC+, catalog number 1761-NET-AIC). For more information on the AIC+, see the
Advanced Interface Converter and DeviceNet Interface Installation Instructions,
Publication 1761-5.11.
DH485 Network with a MicroLogix 1500 Controller
MicroLogix
1500
connection from port 1 or
port 2 to MicroLogix
1761-CBL-AM00 or
1761-CBL-HM02
connection from
port 1 or port 2 to PC
1761-CBL-AP00 or
1761-CBL-PM02
1761-CBL-AP00 or
1761-CBL-PM02
1747-CP3 or
1761-CBL-AC00
+24V dc user supply
+24V dc user supply
D-16
Understanding the Communication Protocols
Typical 3-Node Network
PanelView 550
MicroLogix 1500
1761-CBL-AM00
or 1761-CBL-HM02
RJ45 port
1761-CBL-AS09
or 1761-CBL-AS03
1747-CP3 or 1761-CBL-AC00
D-17
MicroLogix 1500 Programmable Controllers User Manual
Networked Operator Interface Device and MicroLogix 1500 Controller
PanelView 550
RS-232 Port
NULL modem adapter
connection from
PC to AIC+
connection from NULL
modem adapter to AIC+
1761-CBL-AP00 or
1761-CBL-PM02
1761-CBL-AP00 or
1761-CBL-PM02
AIC+
1747-CP3 or
1761-CBL-AC00
AIC+
1747-CP3 or 1761CBL-AC00
+24V dc user supply
+24V dc user supply
AIC+
1747-AIC
+24V dc user supply
1761-CBL-AM00
or 1761-CBL-HM02
SLC 5/03 processor
D-18
MicroLogix 1500
Understanding the Communication Protocols
MicroLogix 1500 Remote Packet Support
MicroLogix 1500 controllers can respond and initiate with device’s communications
(or commands) that do not originate on the local DH485 network. This is useful in
installations where communication is needed between the DH485 and DH+ networks.
The example below shows how to send messages from a PLC device or a PC on the
DH+ network to a MicroLogix 1500 controller on the DH485 network. This method
uses an SLC 5/04 processor bridge connection.
When using this method:
•
PLC-5 devices can send read and write commands to MicroLogix 1500
controllers.
•
MicroLogix 1500 controllers can respond to MSG instructions received. The
MicroLogix 1500 controllers can initiate MSG instructions to devices on the DH+
network.
•
PC can send read and write commands to MicroLogix 1500 controllers.
•
PC can do remote programming of MicroLogix 1500 controllers.
PLC-5
PLC-5
DH+ Network
SLC 5/04
MicroLogix 1500
MicroLogix 1500
DH485 Network
SLC 5/03
MicroLogix 1000
MicroLogix 1000
D-19
MicroLogix 1500 Programmable Controllers User Manual
D-20
System Loading and Heat Dissipation
E
System Loading and
Heat Dissipation
System Loading Limitations
When you connect MicroLogix accessories and expansion I/O, an electrical load is
placed on the base unit power supply. This section shows how to calculate the load
and validate that the system will not exceed the capacity of the base unit power
supply.
The following example is provided to illustrate system loading validation. The system
validation procedure accounts for the amount of 5V dc and 24V dc current consumed
by controller, expansion I/O, and user supplied equipment. Use the “System Loading
Worksheet” on page E-4 to validate your specific configuration.
Current consumed by the Base Units, Memory Modules, Real Time Clock Modules,
and the Right End Cap Terminator (for systems utilizing Compact I/O expansion) has
already been factored into the calculations. A system is valid if the current and power
requirements are satisfied.
Note:
A Right End Cap Terminator (catalog number 1769-ECR) is needed for
any system using Compact expansion I/O.
E-1
MicroLogix 1500 Programmable Controllers User Manual
System Loading Example Calculations
Current Loading
Table 25-5: Calculating the Current for MicroLogix Accessories
Device Current Requirements
at 5V dc (mA)
at 24V dc (mA)
300
0
Catalog Number
1764-LSP
1764-DAT1
350
Calculated Current
at 5V dc (mA) at 24V dc (mA)
300
0
0
350
0
0
650
120
120
1
1761-NET-AIC when powered by the base unit
communications port, selector switch in the up
position
0
120
Subtotal 1:
1. These are optional accessories. Current is consumed only if the accessory is installed.
Table 25-6: Calculating the Current for Expansion I/O
n
Catalog Number1
1769-IA16
1769-IM12
1769-IQ16
1769-OA8
1769-OB16
1769-OV16
1769-OW8
1769-IQ6XOW4
1769-IF4
1769-OF2
Total Modules
(8 maximum):
Number of Modules
1
1
2
1
5
A
B
Device Current Requirements
at 5V dc (mA)
at 24V dc (mA)
115
0
100
0
115
0
145
0
200
0
200
0
125
100
105
50
100
100
100
150
nxA
nxB
Calculated Current
at 5V dc (mA)
at 24V dc (mA)
Subtotal 2:
1. Refer to your Compact I/O Installation Instructions for Current Requirements not listed in this table.
E-2
115
0
200
0
250
105
200
50
670
250
System Loading and Heat Dissipation
Validating the System
The example systems shown in the tables below are verified to be acceptable
configurations. The systems are valid because:
•
Calculated Current Values < Maximum Allowable Current Values
•
Calculated System Loading < Maximum Allowable System Loading
Table 25-7: Validating Systems using 1764-24AWA and 1764-28BXB Base Units
Maximum Allowable Values
Calculated Values
Current:
Current (Subtotal 1 + Subtotal 2 from page E-2.):
2250 mA at 5V dc
400 mA at 24V dc
System Loading:
650 mA + 670 mA = 1320 mA at 5V dc
120 mA + 250 mA = 370 mA at 24V dc
System Loading:
16 Watts
= (1320 mA x 5V) + (370 mA x 24V)
= (6600 mW) + (8880 mW)
= 15,480 mW
= 15.5 Watts
Table 25-8: Validating Systems using 1764-24BWA Base Unit
Maximum Allowable Values
Current for Devices Connected to the +24V
dc User Supply:
400 mA at 24V dc
Current for MicroLogix Accessories and
Expansion I/O:
2250 mA at 5V dc
400 mA at 24V dc
System Loading:
Calculated Values
Sum of all current sensors and/or 1761-NET-AIC connected to the +24V dc
user supply (AIC+ selector switch in the down position1):
150 mA at 24V dc (example sensor value)
Current Values (Subtotal 1 + Subtotal 2 from page E-2.):
650 mA + 670 mA = 1320 mA at 5V dc
120 mA + 250 mA = 370 mA at 24V dc
System Loading:
22 Watts
= (150 mA x 24V) + (1320 mA x 5V) + (370 mA x 24V)
= (3600 mW) + (6600 mW) + (8880 mW)
= 19,080 mW
= 19.1 Watts
1. No current is consumed from the controller when the AIC+ is powered by an external source.
E-3
MicroLogix 1500 Programmable Controllers User Manual
System Loading Worksheet
The tables below are provided for system loading validation. See “System Loading
Example Calculations” on page E-2 for an illustration of system loading validation.
Current Loading
Table 25-9: Calculating the Current for MicroLogix Accessories
Device Current Requirements
at 5V dc (mA)
at 24V dc (mA)
300
0
Catalog Number
1764-LSP
1764-DAT1
350
Calculated Current
at 5V dc (mA) at 24V dc (mA)
0
1
1761-NET-AIC when powered by the base unit
communications port, selector switch in the up
position
0
120
Subtotal 1:
1. These are optional accessories. Current is consumed only if the accessory is installed.
Table 25-10: Calculating the Current for Expansion I/O
n
Catalog Number1
1769-IA16
1769-IM12
1769-IQ16
1769-OA8
1769-OB16
1769-OV16
1769-OW8
1769-IQ6XOW4
1769-IF4
1769-OF2
Total Modules
(8 maximum):
Number of Modules
1
1
2
1
5
A
B
Device Current Requirements
at 5V dc (mA)
at 24V dc (mA)
115
0
100
0
115
0
145
0
200
0
200
0
125
100
105
50
100
100
100
150
nxA
nxB
Calculated Current
at 5V dc (mA)
at 24V dc (mA)
Subtotal 2:
1. Refer to your Compact I/O Installation Instructions for Current Requirements not listed in this table.
E-4
System Loading and Heat Dissipation
Validating the System
The example systems shown in the tables below are verified to be acceptable
configurations. The systems are valid because:
•
Calculated Current Values < Maximum Allowable Current Values
•
Calculated System Loading < Maximum Allowable System Loading
Table 25-11: Validating Systems using 1764-24AWA and 1764-28BXB Base Units
Maximum Allowable Values
Calculated Values
Current:
Current (Subtotal 1 + Subtotal 2 from page E-2.):
2250 mA at 5V dc
400 mA at 24V dc
System Loading:
System Loading:
16 Watts
Table 25-12: Validating Systems using 1764-24BWA Base Unit
Maximum Allowable Values
Current for Devices Connected to the +24V
dc User Supply:
Calculated Values
Sum of all current sensors and/or 1761-NET-AIC connected to the +24V dc
user supply (AIC+ selector switch in the down position 1):
400 mA at 24V dc
Current for MicroLogix Accessories and
Expansion I/O:
2250 mA at 5V dc
mA at 24V dc
Current Values (Subtotal 1 + Subtotal 2 from page E-2.):
400 mA at 24V dc
System Loading:
mA at 5 V dc
mA at 24V dc
System Loading:
22 Watts
= ( ________ mA x 24V) + ( ________ mA x 5V) + ( ________ mA x 24V)
= __________ mW + __________ mW + __________ mW
= __________ mW
= __________ W
1. No current is consumed from the controller when the AIC+ is powered by an external source.
E-5
MicroLogix 1500 Programmable Controllers User Manual
Calculating Heat Dissipation
Use this procedure when you need to determine the heat dissipation for installation in
an enclosure. Use the following table. For System Loading, take the value from the
table on page E-5:
Catalog Number
1764-24AWA
1764-24BWA
1764-28BXB
1764-LSP
1764-DAT
1764-MM1, -RTC, -MM1/RTC
1769-IA16
1769-IM12
1769-IQ16
1769-OA8
1769-OB16
1769-OV16
1769-OW8
1769-IQ6XOW4
1769-IF4
1769-OF2
Equation or Constant
18W + (0.3 x System Loading)
20W + (0.3 x System Loading)
20W + (0.3 x System Loading)
1.5W
1.75W
0
3.30W x number of modules
3.65W x number of modules
3.55W x number of modules
2.12W x number of modules
2.11W x number of modules
2.06W x number of modules
2.83W x number of modules
2.75W x number of modules
Heat Dissipation
Calculation
18W + (0.3 x ______ W)
20W + (0.3 x ______ W)
20W + (0.3 x ______ W)
3.30W x __________
3.65W x __________
3.55W x __________
2.12W x __________
2.11W x __________
2.06W x __________
2.83W x __________
2.75W x __________
Add Sub-Totals to determine Heat Dissipation
E-6
Sub-Total
Memory Usage and Instruction Execution Time
F
Memory Usage and
Instruction Execution Time
This appendix contains a complete list of the MicroLogix 1500 programming
instructions. The list shows the memory usage and instruction execution time for each
instruction. Execution times using indirect addressing and a scan time worksheet are
also provided.
Programming Instructions Memory Usage and Execution Time
Table F-1 on page F-2 lists the execution times and memory usage for the
programming instructions. These values depend on whether you are using word or
long word as the data format.
F-1
MicroLogix 1500 Programmable Controllers User Manual
Table F-1: MicroLogix 1500 Memory Usage and Instruction Execution Time for Programming Instructions
Word
Execution Time in µs
Instruction
Programming Instruction
Mnemonic
Add
ADD
And
AND
Bit Shift Left
BSL
Bit Shift Right
BSR
Clear
CLR
File Copy
COP
Count Down
CTD
Count Up
CTU
Decode 4-to-1 of 16
DCD
Divide
DIV
Encode 1-of-16 to 4
ENC
Equal
EQU
FIFO Load
FFL
FIFO Unload
FFU
Fill File
FLL
Convert from BCD
FRD
Greater Than or Equal To
GEQ
Greater Than
GRT
High Speed Load
HSL
Immediate Input with Mask IIM
Interrupt Subroutine
INT
Immediate Output with Mask IOM
Jump
JMP
Jump to Subroutine
JSR
Label
LBL
Less Than or Equal To
LEQ
Less Than
LES
LIFO Load
LFL
LIFO Unload
LFU
Limit
LIM
Master Control Reset
MCR (Start)
MCR (End)
F-2
False
0.00
0.00
0.00
0.00
0.00
0.00
8.30
8.40
0.00
0.00
0.00
0.94
9.50
9.50
0.00
0.00
0.94
0.94
0.00
0.00
0.16
0.00
0.00
0.00
0.16
1.02
1.02
9.50
9.50
5.79
0.66
0.87
Memory
Usage in
Words
True
2.12
3.25
2.00
2.75
29+1.08/word
3.75
29+1.14/word
3.75
1.18
1.00
16+0.7/word
2.00
8.30
2.38
7.80
2.38
1.68
1.88
9.95
2.00
6.90
1.50
1.30
1.25
20.00
3.38
18+0.727/word
3.38
13+0.43/word
2.00
12.61
1.50
1.30
1.25
1.30
1.25
41.85
7.25
22.06
3.00
0.16
0.25
19.44
3.00
0.39
0.50
6.43
1.50
0.16
0.50
1.30
1.25
1.22
1.25
20.00
3.38
20.80
3.38
6.43
2.25
0.66
1.00
0.87
1.50
Long Word
Execution Time in µs
False
0.00
0.00
True
10.82
8.20
Memory
Usage in
Words
3.50
3.00
Long Word addressing level does not apply.
0.00
5.49
1.00
Long Word addressing level does not apply.
0.00
32.92
3.50
Long Word addressing level does not apply.
1.41
2.27
2.63
9.50
23.00
3.88
9.50
20+1.39/Lword
3.38
0.00
13.7+0.85/Lword
2.50
Long Word addressing level does not apply.
2.27
2.59
2.88
2.27
2.59
2.38
0.00
42.95
7.75
Long Word addressing level does not apply.
2.27
2.27
9.50
9.50
11.59
2.59
2.59
24.00
24.00
12.41
2.88
2.88
3.88
3.38
4.00
Long Word addressing level does not apply.
Memory Usage and Instruction Execution Time
Table F-1: MicroLogix 1500 Memory Usage and Instruction Execution Time for Programming Instructions
Word
Execution Time in µs
Programming Instruction
Masked Comparison for
Equal
Move
Message, Steady State
Message, False-to-True
Transition for Reads
Message, False-to-True
Transition for Writes
Multiply
Masked Move
Negate
Not Equal
Not
One Shot
Or
One Shot Falling
One Shot Rising
Output Enable
Output Latch
Output Unlatch
Proportional Integral
Derivative
Pulse Train Output
Pulse Width Modulation
Reset Accumulator
I/O Refresh
Reset
Return
Retentive Timer On
Subroutine
Scale
Scale with Parameters
Sequencer Compare
Sequencer Load
Instruction
Mnemonic
MEQ
False
1.97
True
2.07
MOV
MSG
0.00
6.00
2.15
8.00
150.00
Memory
Usage in
Words
1.75
2.50
2.88
Long Word
Execution Time in µs
False
2.58
True
3.37
Memory
Usage in
Words
3.50
0.00
7.18
2.00
Long Word addressing level does not apply.
200+1.3/word
MUL
MVM
NEG
NEQ
NOT
ONS
OR
OSF
OSR
OTE
OTL
OTU
PID
PTO
PWM
RAC
REF
RES
RET
RTO
SBR
SCL
SCP
SQC
SQL
0.00
0.00
0.00
0.94
0.00
1.85
0.00
3.01
2.43
0.98
0.00
0.00
9.65
5.88
7.05
2.35
1.30
2.20
1.38
2.00
1.88
2.71
1.49
1.06
1.02
263.19
2.00
2.00
3.00
1.25
2.50
3.50
2.75
5.38
5.38
1.63
0.63
0.63
2.38
0.00
28.55
3.50
0.00
10.58
3.00
0.00
10.18
3.00
2.20
1.80
2.50
0.00
7.99
2.50
Long Word addressing level does not apply.
0.00
8.19
3.00
Long Word addressing level does not apply.
21.40
75.11
1.88
21.63
110.50
1.88
Word addressing level does not apply.
0.00
17.61
2.00
0.00
see p. F-8
0.50
0.00
4.94
1.00
0.00
0.44
0.25
Long Word addressing level does not apply.
1.85
15.73
3.38
0.16
0.16
0.25
0.00
9.30
2.50
0.00
28.44
3.75
0.00
45.59
6.00
6.80
21.30
3.88
6.80
22.80
4.38
6.80
19.20
3.38
6.80
21.10
3.88
F-3
MicroLogix 1500 Programmable Controllers User Manual
Table F-1: MicroLogix 1500 Memory Usage and Instruction Execution Time for Programming Instructions
Word
Execution Time in µs
Programming Instruction
Sequencer Output
Square Root
Selectable Timed Interrupt
Start
Subtract
Suspend
Service Communications
Temporary End
Convert to BCD
Off-Delay Timer
On-Delay Timer
User Interrupt Disable
User Interrupt Enable
User Interrupt Flush
Examine if Closed
Examine if Open
Exclusive Or
F-4
Instruction
Mnemonic
SQO
SQR
STS
False
6.80
0.00
0.00
True
20.20
22.51
62.73
Memory
Usage in
Words
3.88
1.50
1.00
SUB
SUS
SVC
TND
TOD
TOF
TON
UID
UIE
UIF
XIC
XIO
XOR
0.00
0.00
0.00
0.00
0.00
12.32
2.16
0.00
0.00
0.00
0.63
0.63
0.00
3.06
0.66
135+300/word
0.33
14.64
1.85
15.49
0.59
0.66
9.79
0.51
0.51
2.67
3.25
1.50
1.00
0.50
1.75
3.88
3.88
0.88
0.88
0.88
1.00
1.00
2.75
Long Word
Execution Time in µs
False
6.80
0.00
True
23.40
26.58
Memory
Usage in
Words
4.38
2.50
Long Word addressing level does not apply.
0.00
11.22
3.50
Long Word addressing level does not apply.
0.00
8.81
3.00
Memory Usage and Instruction Execution Time
Indirect Addressing
The following sections describe how indirect addressing affects the execution time of
instructions in the Micrologix 1500 processor. The timing for an indirect address is
affected by the form of the indirect address.
For the address forms in the following table, you can interchange the following file
types:
•
Input (I) and Output (O)
•
Bit (B), Integer (N)
•
Timer (T), Counter (C), and Control (R)
Execution Times for the Indirect Addresses
For most types of instructions that contain an indirect address(es), look up the form of
the indirect address in the table below and add that time to the execution time of the
instruction.
[*] indicates that an indirect reference is substituted.
Table F-2: MicroLogix 1500 Instruction Execution Time Using Indirect Addressing
Address Form
O:1.[*]
O:[*].0
O:[*].[*]
B3:[*]
B[*]:1
B[*]:[*]
L8:[*]
L[*]:1
L[*]:[*]
T4:[*]
T[*]:1
T[*]:[*]
T4:[*].ACC
T[*]:1.ACC
T[*]:[*].ACC
O:1.[*]/2
O:[*].0/2
Operand Time (µs)
5.15
13.24
13.71
5.15
21.58
22.04
5.18
21.18
21.26
6.04
21.82
21.74
6.02
21.49
22.20
4.98
12.83
F-5
MicroLogix 1500 Programmable Controllers User Manual
Table F-2: MicroLogix 1500 Instruction Execution Time Using Indirect Addressing
Address Form
O:[*].[*]/2
O:1.0/[*]
O:1.[*]/[*]
O:[*].0/[*]
O:[*].[*]/[*]
B3:[*]/2
B[*]:1/2
B[*]:[*]/2
B3:1/[*]
B3:[*]/[*]
B[*]:1/[*]
B[*]:[*]/[N7:3]
L8:[*]/2
L[*]:1/2
L[*]:[*]/2
L8:1/[*]
L8:[*]/[*]
L[*]:1/[*]
L[*]:[*]/[*]
T4:[*]/DN
T[*]:1/DN
T[*]:[*]/DN
T4:[*].ACC/2
T[*]:1.ACC/2
T[*]:[*].ACC/2
T4:1/[*]
T4:[*]/[*]
T[*]:1/[*]
T[*]:[*]/[*]
T4:1.ACC/[*]
T4:[*].ACC/[*]
T[*]:1.ACC/[*]
T[*]:[*].ACC/[*]
F-6
Operand Time (µs)
13.38
6.29
7.23
15.24
15.10
4.98
21.21
21.85
6.29
7.23
23.73
23.58
4.87
20.98
21.85
6.29
7.38
23.73
23.41
5.14
20.99
21.45
5.89
20.98
22.39
6.21
7.78
23.49
23.73
6.21
8.17
23.49
24.51
Memory Usage and Instruction Execution Time
Execution Time Example – Word Level Instruction Using and Indirect Address
ADD Instruction Addressing
Source A: N7:[*]
Source B: T4:[*].ACC
Destination: N[*]:[*]
ADD Instruction Times
ADD Instruction: 2.12 µs
Source A: 5.15 µs
Source B: 6.02 µs
Destination: 22.04 µs
Total = 35.33 µs
Execution Time Example – Bit Instruction Using an Indirect Address
XIC B3/[*]
XIC: 0.51 µs + 5.15 µs = 5.66 µs True case
XIC: 0.63 µs + 5.15 µs = 5.78 µs False case
F-7
MicroLogix 1500 Programmable Controllers User Manual
Scan Time Worksheet
Calculate the scan time for you control program using the worksheet below.
Input Scan (sum of below)
Overhead (if expansion I/O is used)
Expansion Input Words X 3 µs (or X 7.5 µs if Forcing is used)
Number of modules with Input words X 10 µs
= 53 µs
=
=
Input Scan Sub-Total =
Program Scan
Add execution times of all instructions in your program when executed true
=
Program Scan Sub-Total =
Output Scan (sum of below)
Overhead (if expansion I/O used)
Expansion Output Words X 2 µs (or X 6.5 µs if Forcing is used)
= 29 µs
=
Output Scan Sub-Total =
Communications Overhead1
Worst Case
Typical Case
= 1100 µs
= 400 µs
Communications Overhead Sub-Total
Add this number if your system includes a 1764-RTC or 1764-MM1RTC.
= 80 µs
Add this number if your system includes a 1764-DAT
= 530 µs
Housekeeping Overhead
Sum of All
Multiply by Communications Multiplier from Table
Total Scan Time
1.
=
=
=
= 300 µs
=
X
=
Communications Overhead is a function of the device connected to the controller. This will not occur every scan.
Communications Multiplier Table
Protocol
DF1 Full Duplex
DF1 Half Duplex
DH485
Shut Down
38.4K
1.45
1.16
N/A
1.00
Multiplier at Various Baud Rates
19.2K
9.6K
1.19
1.07
1.07
1.00
1. Inactive is defined as No Messaging and No Data Monitoring
F-8
1.09
1.04
1.04
1.00
Inactive1
1.06
1.00
N/A
1.00
System Status File
G
System Status File
The status file lets you monitor how your controller works and lets you direct how
you want it to work. This is done by using the status file to set up control bits and
monitor both hardware and programming device faults and other status information.
Important:
Do not write to reserved words in the status file. If you intend
writing to status file data, it is imperative that you first understand
the function fully.
Status File Overview
The status file (S:) contains the following words:
Address
S:0
S:1
S:2
S:3H
S:4
S:5
S:6
S:7
S:8
S:9
S:10
S:13, S:14
S:15L
S:15H
S:22
S:29
S:30
S:31
S:33
Function
Arithmetic Flags
Controller Mode
Controller Alternate Mode
Watchdog Scan Time
Free Running Clock
Minor Error Bits
Major Error
Suspend Code
Suspend File
Active Nodes Channel 0 (Nodes 0 to 15)
Active Node Channel 0 (Nodes 16 to 31)
Math Register
Node Address
Baud Rate
Maximum Scan Time
User Fault File
STI Setpoint
STI File Number
Channel 0 Communications
Page
G-3
G-4
G-9
G-11
G-12
G-12
G-15
G-15
G-15
G-16
G-16
G-16
G-17
G-17
G-17
G-18
G-18
G-18
G-19
G-1
MicroLogix 1500 Programmable Controllers User Manual
Address
S:35
S:36/10
S:37
S:38
S:39
S:40
S:41
S:42
S:53
S:57
S:58
S:59
S:60
S:61
S:62
S:63
S:64L
S:64H
G-2
Function
Last 100 µSec Scan Time
Data File Overwrite Protection Lost
RTC Year
RTC Month
RTC Day of Month
RTC Hours
RTC Minutes
RTC Seconds
RTC Day of Week
OS Catalog Number
OS Series
OS FRN
Controller Catalog Number
Controller Series
Controller Revision
User Program Functionality Type
Compiler Revision - Build Number
Compiler Revision - Release
Page
G-21
G-21
G-21
G-22
G-22
G-22
G-22
G-23
G-23
G-23
G-24
G-24
G-24
G-24
G-24
G-25
G-25
G-25
System Status File
Status File Details
Arithmetic Flags
The arithmetic flags are assessed by the processor following the execution of any
math, logical, or move instruction. The state of these bits remains in effect until the
next math, logical, or move instruction in the program is executed.
Carry Flag
Address
S:0/0
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
This bit is set (1) if a mathematical carry or borrow is generated. Otherwise the bit
remains cleared (0). When a STI, High Speed Counter, Event Interrupt, or User Fault
Routine interrupts normal execution of your program, the original value of S:0/0 is
restored when execution resumes.
OverFlow Flag
Address
S:0/1
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
This bit is set (1) when the result of a mathematical operation does not fit in the
destination. Otherwise the bit remains cleared (0). Whenever this bit is set (1), the
overflow trap bit S:5/0 is also set (1). When an STI, High Speed Counter, Event
Interrupt, or User Fault Routine interrupts normal execution of your program, the
original value of S:0/1 is restored when execution resumes.
Zero Flag
Address
S:0/2
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
This bit is set (1) when the result of a mathematical operation or data handling
instruction is zero. Otherwise the bit remains cleared (0). When an STI, High Speed
Counter, Event Interrupt, or User Fault Routine interrupts normal execution of your
program, the original value of S:0/2 is restored when execution resumes.
G-3
MicroLogix 1500 Programmable Controllers User Manual
Sign Flag
Address
S:0/3
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
This bit is set (1) when the result of a mathematical operation or data handling
instruction is negative. Otherwise the bit remains cleared (0). When a STI, High
Speed Counter, Event Interrupt, or User Fault Routine interrupts normal execution of
your program, the original value of S:0/3 is restored when execution resumes.
Controller Mode
User Application Mode
Address
S:1/0 to S:1/4
Data Format
binary
Range
0 to 1 1110
Type
status
User Program Access
read only
Bits 0-4 function as follows:
S:1/4
0
0
0
G-4
S:1/0 to S:1/4
S:1/3 S:1/2 S:1/1
0
0
0
0
0
0
0
0
1
S:1/0
0
1
1
0
0
0
1
1
1
0
0
1
0
0
1
1
1
0
0
0
0
1
1
0
0
0
1
0
1
0
0
1
1
1
1
1
1
0
Mode
ID
Controller Mode
0
remote download in progress
1
remote program mode
3
remote suspend mode
(operation halted by execution of the SUS instruction)
6
remote run mode
7
remote test continuous mode
8
remote test single scan mode
16 download in progress
17 program mode
27 suspend mode
(operation halted by execution of the SUS instruction)
30 run mode
System Status File
Forces Enabled
Address
S:1/5
Data Format
binary
Range
1
Type
status
User Program Access
read only
This bit is set (1) by the controller to indicate that forces are enabled.
Forces Installed
Address
S:1/6
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read only
This bit is set (1) by the controller to indicate that 1 or more inputs or outputs are
forced. When this bit is clear a force condition is not present within the controller.
Fault Override At Power-Up
Address
S:1/8
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read only
When set (1), causes the controller to clear the Major Error Halted bit (S:1/13) at
power-up. The power-up mode is determined by the controller mode switch and the
Power-Up Mode Behavior Selection bit (S:1/12).
See also: “Fault Override” on page 8-7.
Startup Protection Fault
Address
S:1/9
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read only
When set (1) and the controller powers up in the RUN or REM RUN mode, the
controller executes the User Fault Routine prior to the execution of the first scan of
your program. You have the option of clearing the Major Error Halted bit (S:1/13) to
resume operation. If the User Fault Routine does not clear bit S:1/13, the controller
faults and does not enter an executing mode. Program the User Fault Routine logic
accordingly.
Note:
When executing the startup protection fault routine, S:6 (major error fault
code) contains the value 0016H.
G-5
MicroLogix 1500 Programmable Controllers User Manual
Load Memory Module On Error Or Default Program
Address
S:1/10
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read only
For this option to work, you must set (1) this bit in the control program before
downloading the program to a memory module. When this bit it set in the memory
module and power is applied, the controller downloads the memory module program
when the control program is corrupt or a default program exists in the controller.
Note:
If you clear the controller memory, the controller will load the default
program.
The mode of the controller after the transfer takes place is determined by the
controller mode switch and the Power-Up Mode Behavior Selection bit (S:1/12).
See also: “Load on Error” on page 8-8.
Load Memory Module Always
Address
S:1/11
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read only
For this option to work, you must set (1) this bit in the control program before
downloading the program to a memory module. When this bit it set in the memory
module and power is applied, the controller downloads the memory module program.
The mode of the controller after the transfer takes place is determined by the
controller mode switch and the Power-Up Mode Behavior Selection bit (S:1/12).
See also: “Load Always” on page 8-8.
G-6
System Status File
Power-Up Mode Behavior
Address
S:1/12
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read only
If Power-Up Mode Behavior is clear (0 = Last State), the mode at power-up is
dependent upon the:
• position of the mode switch,
• state of the Major Error Halted flag (S:1/13)
• mode at the previous power down
If Power Up Mode Behavior is set (1 = Run), the mode at power-up is dependent upon
the:
• position of the mode switch
• state of the Major Error Halted flag (S:1/13)
Important:
If you want the controller to power-up and enter the Run mode,
regardless of any previous fault conditions, you must also set the
Fault Override bit (S:1/8) so that the Major Error Halted flag is
cleared before determining the power up mode.
The following table shows the Power-Up Mode under various conditions
Mode Switch Position Major Error Power-Up Mode
at Power-Up
Halted
Behavior
Program
Remote
False
True
False
True
Run
False
True
1.
Don’t Care
Last State
Mode at Last Power-Down
Don’t Care
Power-Up Mode
Program
Program w/Fault
REM Download, Download, REM Program, Program or Any
REM Program
Test mode
REM Suspend or Suspend
REM Suspend
REM Run or Run
REM Run
Run
Don’t Care
REM Run
Don’t Care
Don’t Care
REM Program w/Fault
REM Suspend or Suspend
Suspend
Last State
Any Mode except
REM Suspend or Suspend
Run
Run
Don’t Care
Run
Don’t Care
Don’t Care
Run w/Fault1
Run w/Fault is a fault condition, just as if the controller were in the Program /w Fault mode (outputs are reset and the controller program is
not being executed). However, the controller will enter Run mode as soon as the Major Error Halted flag is cleared.
See also: “Mode Behavior” on page 8-8.
G-7
MicroLogix 1500 Programmable Controllers User Manual
Major Error Halted
Address
S:1/13
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
The controller sets (1) this bit when a major error is encountered. The controller
enters a fault condition and word S:6 contains the Fault Code that can be used to
diagnose the condition. Any time bit S:1/13 is set, the controller:
•
turns all outputs off and flashes the FAULT LED,
•
or, enters the User Fault Routine allowing the control program to attempt recovery
from the fault condition. If the User Fault Routine is able to clear S:1/13 and the
fault condition, the controller continues to execute the control program. If the fault
cannot be cleared, the outputs are cleared and the controller exits its executing
mode and the FAULT LED flashes.
!
ATTENTION: If you clear the Major Error Halted bit (S:1/13) when
the controller mode switch is in the RUN position, the controller
immediately enters the RUN mode.
Future Access (OEM Lock)
Address
S:1/14
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read only
When this bit is set (1), it indicates that the programming device must have an exact
copy of the controller program.
See “Allow Future Access Setting (OEM Lock)” on page 6-11 for more information.
G-8
System Status File
First Pass
Address
S:1/15
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
When the controller sets (1) this bit, it indicates that the first scan of the user program
is in progress (following entry into an executing mode). The controller clears this bit
after the first scan.
Note:
The First Pass bit (S:1/15) is set during execution of the start-up protection
fault routine. Refer to S:1/9 for more information.
Controller Alternate Mode
STI Pending
Address1
S:2/0
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated at STI:0/UIP. See “Using the Selectable Timed Interrupt
(STI) Function File” on page 23-13 for more information.
STI Enabled
Address1
S:2/1
Data Format
Range
Type
User Program Access
binary
0 or 1
control
read/write
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated at STI:0/TIE. See “Using the Selectable Timed Interrupt
(STI) Function File” on page 23-13 for more information.
G-9
MicroLogix 1500 Programmable Controllers User Manual
STI Executing
Address1
S:2/2
Data Format
Range
Type
User Program Access
binary
0 or 1
control
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated at STI:0/UIX. See “Using the Selectable Timed Interrupt
(STI) Function File” on page 23-13 for more information.
Memory Module Program Compare
Address
S:2/9
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read only
When this bit is set (1) in the controller, its user program and the memory module user
program must match for controller to enter an executing mode.
If the user program does not match the memory module program, or if the memory
module is not present, the controller faults with error code 0017H on any attempt to
enter an executing mode.
An RTC module does not support program compare. If program compare is enabled
and an RTC-only module is installed, the controller does not enter an executing mode.
See also: “Load Program Compare” on page 8-8.
G-10
System Status File
Math Overflow Selection
Address
S:2/14
Data Format
binary
Range
0 or 1
Type
control
User Program Access
read/write
Set (1) this bit when you intend to use 32-bit addition and subtraction. When S:2/14 is
set, and the result of an ADD, SUB, MUL, or DIV instruction cannot be represented
in the destination address (underflow or overflow),
•
the overflow bit S:0/1 is set,
•
the overflow trap bit S:5/0 is set,
•
and the destination address contains the unsigned truncated least significant 16 or
32 bits of the result.
The default condition of S:2/14 is cleared (0). When S:2/14 is cleared (0), and the
result of an ADD, SUB, MUL, or DIV instruction cannot be represented in the
destination address (underflow or overflow),
•
the overflow bit S:0/1 is set,
•
the overflow trap bit S:5/0 is set,
•
the destination address contains +32,767 (word) or +2,147,483,647 (long word) if
the result is positive; or -32,768 (word) or -2,147,483,648 (long word) if the result
is negative.
To provide protection from inadvertent alteration of your selection, program an
unconditional OTL instruction at address S:2/14 to ensure the new math overflow
operation. Program an unconditional OTU instruction at address S:2/14 to ensure the
original math overflow operation.
Watchdog Scan Time
Address
S:3H
Data Format
Byte
Range
2 to 255
Type
control
User Program Access
read/write
This byte value contains the number of 10 ms intervals allowed to occur during a
program cycle. The timing accuracy is from -10 ms to +0 ms. This means that a value
of 2 results in a timeout between 10 and 20 ms.
If the program scan time value equals the watchdog value, a watchdog major error is
generated (code 0022H).
G-11
MicroLogix 1500 Programmable Controllers User Manual
Free Running Clock
Address
S:4
Data Format
binary
Range
0 to FFFF
Type
status
User Program Access
read/write
This register contains a free running counter that is incremented every 100 µs. This
word is cleared (0) upon entering an executing mode.
Minor Error Bits
Overflow Trap Bit
Address
S:5/0
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
If this bit is ever set (1) upon execution of the END or TND instruction, a major error
(0020H) is generated. To avoid this type of major error from occurring, examine the
state of this bit following a math instruction (ADD, SUB, MUL, DIV, NEG, SCL,
TOD, or FRD), take appropriate action, and then clear bit S:5/0 using an OTU
instruction with S:5/0.
Control Register Error
Address
S:5/2
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
The LFU, LFL, FFU, FFL, BSL, BSR, SQO, SQC, and SQL instructions are capable
of generating this error. When bit S:5/2 is set (1), it indicates that the error bit of a
control word used by the instruction has been set.
If this bit is ever set upon execution of the END or TND instruction, major error
(0020H) is generated. To avoid this type of major error from occurring, examine the
state of this bit following a control register instruction, take appropriate action, and
then clear bit S:5/2 using an OTU instruction with S:5/2.
G-12
System Status File
Major Error While Executing User Fault Routine
Address
S:5/3
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
When set (1), the major error code (S:6) represents the major error that occurred
while processing the User Fault Routine due to another major error.
Memory Module Boot
Address
S:5/8
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
When this bit is set (1) by the controller, it indicates that a memory module program
has been transferred due to S:1/10 (Load Memory Module on Error or Default
Program) or S:1/11 (Load Memory Module Always) being set in an attached memory
module user program. This bit is not cleared (0) by the controller.
Your program can examine the state of this bit on the first scan (using bit S:1/15) on
entry into an Executing mode to determine if the memory module user program has
been transferred after a power-up occurred. This information is useful when you have
an application that contains retentive data and a memory module has bit S:1/10 or bit
S:1/11 set.
Memory Module Password Mismatch
Address
S:5/9
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
At power-up, if Load Always is set, and the controller and memory module passwords
do not match, the Memory Module Password Mismatch bit is set (1).
See “Password Protection” on page 6-9 for more information.
G-13
MicroLogix 1500 Programmable Controllers User Manual
STI Lost
Address1
S:5/10
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read/write
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated at STI:0/UIL. See “Using the Selectable Timed Interrupt
(STI) Function File” on page 23-13 for more information.
Processor Battery Low
Address
S:5/11
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read only
This bit is set (1) when the battery is low.
Important:
Install a replacement battery immediately. See “Lithium Battery
(1747-BA)” on page B-2 for more information.
Input Filter Selection Modified
Address
S:5/13
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
This bit is set (1) whenever the discrete input filter selection in the control program is
not compatible with the hardware.
G-14
System Status File
Major Error
Address
S:6
Data Format
word
Range
0 to FFFF
Type
status
User Program Access
read/write
This register displays a value which can be used to determine what caused a fault to
occur. See “Troubleshooting Your System” on page C-1 to learn more about
troubleshooting faults.
Suspend Code
Address
S:7
Data Format
word
Range
-32,768 to
+32,767
Type
status
User Program Access
read/write
When the controller executes an Suspend (SUS) instruction, the SUS code is written
to this location, S:7. This pinpoints the conditions in the application that caused the
Suspend mode. The controller does not clear this value.
Use the SUS instruction with startup troubleshooting, or as runtime diagnostics for
detection of system errors.
Suspend File
Address
S:8
Data Format
word
Range
0 to 255
Type
status
User Program Access
read/write
When the controller executes an Suspend (SUS) instruction, the SUS file is written to
this location, S:8. This pinpoints the conditions in the application that caused the
Suspend mode. The controller does not clear this value.
Use the SUS instruction with startup troubleshooting, or as runtime diagnostics for
detection of system errors.
G-15
MicroLogix 1500 Programmable Controllers User Manual
Active Nodes Channel 0 (Nodes 0 to 15)
Address1
S:9
Data Format
Range
Type
User Program Access
word
0 to FFFF
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File. See “Active Node Table
Block” on page 6-16 for more information.
Active Node Channel 0 (Nodes 16 to 31)
Address1
S:10
Data Format
Range
Type
User Program Access
word
0 to FFFF
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File. See “Active Node Table
Block” on page 6-16 for more information.
Math Register
Address
S:13
Data Format
word
S:14
word
Range
-32,768 to
+32,767
-32,768 to
+32,767
Type
status
User Program Access
read/write
status
read/write
These two words are used in conjunction with the MUL, DIV, FRD, and TOD math
instructions. The math register value is assessed upon execution of the instruction and
remains valid until the next MUL, DIV, FRD, or TOD instruction is executed in the
user program.
An explanation of how the math register operates is included with the instruction
definitions.
G-16
System Status File
Node Address
Address1
S:15 (low byte)
Data Format
Range
Type
User Program Access
byte
0 to 255
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File. See “Channel 0
General Channel Status Block” on page 6-14 for more information.
Baud Rate
Address1
S:15 (high byte)
Data Format
Range
Type
User Program Access
byte
0 to 255
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File. See “Channel 0
General Channel Status Block” on page 6-14 for more information.
Maximum Scan Time
Address
S:22
Data Format
word
Range
0 to 32,767
Type
status
User Program Access
read/write
This word indicates the maximum observed interval between consecutive program
cycles.
This value indicates, in 100 us increments, the time elapsed in the longest program
cycle of the controller The controller compares each scan value to the value contained
in S:22. If the controller determines that the last scan value is larger than the previous,
the larger value is stored in S:22.
Resolution of the maximum observed scan time value is -100 µs to +0 µs. For
example, the value 9 indicates that 800 to 900 us was observed as the longest program
cycle.
Interrogate this value if you need to determine the longest scan time of your program.
G-17
MicroLogix 1500 Programmable Controllers User Manual
User Fault File
Address
S:29
Data Format
word
Range
0 to 255
Type
status
User Program Access
read only
This register is used to control which subroutine executes when a User Fault is
generated.
STI Setpoint
Address1
S:30
Data Format
Range
Type
User Program Access
word
0 to 65535
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated at STI:0/SPM. See “Using the Selectable Timed Interrupt
(STI) Function File” on page 23-13 for more information.
STI File Number
Address1
S:31
Data Format
Range
Type
User Program Access
word
0 to 65535
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated at STI:0/PFN. See “Using the Selectable Timed Interrupt
(STI) Function File” on page 23-13 for more information.
G-18
System Status File
Channel 0 Communications
Incoming Command Pending
Address1
S:33/0
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File at CS0:4/0. See
“Channel 0 General Channel Status Block” on page 6-14 for more information.
Message Reply Pending
Address1
S:33/1
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File at CS0:4/1. See
“Channel 0 General Channel Status Block” on page 6-14 for more information.
Outgoing Message Command Pending
Address1
S:33/2
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File at CS0:4/2. See
“Channel 0 General Channel Status Block” on page 6-14 for more information.
G-19
MicroLogix 1500 Programmable Controllers User Manual
Communications Mode Selection
Address1
S:33/3
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File at CS0:4/3. See
“Channel 0 General Channel Status Block” on page 6-14 for more information.
Communications Active
Address1
S:33/4
Data Format
Range
Type
User Program Access
binary
0 or 1
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
This address is duplicated in the Communications Status File at CS0:4/4. See
“Channel 0 General Channel Status Block” on page 6-14 for more information.
Scan Toggle Bit
Address
S:33/9
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
The controller changes the status of this bit at the end of each scan. It is reset upon
entry into an executing mode.
G-20
System Status File
Last 100 µSec Scan Time
Address
S:35
Data Format
word
Range
0 to 32,767
Type
status
User Program Access
read/write
This register indicates the elapsed time for the last program cycle of the controller (in
100 µs increments).
Data File Overwrite Protection Lost
Address
S:36/10
Data Format
binary
Range
0 or 1
Type
status
User Program Access
read/write
When clear (0), this bit indicates that at the time of the last program transfer to the
controller, protected data files in the controller were not overwritten, or there were no
protected data files in the program being downloaded.
When set (1), this bit indicates that the default data has been loaded. See “User
Program Transfer Requirements” on page 6-8 for more information.
See “Setting Download File Protection” on page 6-6 for more information.
RTC Year
Address1
S:37
Data Format
Range
Type
User Program Access
word
1998 to 2097
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
G-21
MicroLogix 1500 Programmable Controllers User Manual
RTC Month
Address1
S:38
Data Format
Range
Type
User Program Access
word
1 to 12
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
RTC Day of Month
Address1
S:39
Data Format
Range
Type
User Program Access
word
1 to 31
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
RTC Hours
Address1
S:40
Data Format
Range
Type
User Program Access
word
0 to 23
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
RTC Minutes
Address1
S:41
Data Format
Range
Type
User Program Access
word
0 to 59
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
G-22
System Status File
RTC Seconds
Address1
S:42
Data Format
Range
Type
User Program Access
word
0 to 59
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
RTC Day of Week
Address1
S:53
Data Format
Range
Type
User Program Access
word
0 to 6
status
read only
1. This bit can only be accessed via ladder logic. It cannot be accessed via communications (such as a Message instruction
from another device).
See “Real Time Clock Function File” on page 8-2 for more information.
OS Catalog Number
Address
S:57
Data Format
word
Range
0 to 32,767
Type
status
User Program Access
read only
This register identifies the Catalog Number for the Operating System in the controller.
G-23
MicroLogix 1500 Programmable Controllers User Manual
OS Series
Address
S:58
Data Format
ASCII
Range
A to Z
Type
status
User Program Access
read only
This register identifies the Series letter for the Operating System in the controller.
OS FRN
Address
S:59
Data Format
word
Range
0 to 32,767
Type
status
User Program Access
read only
This register identifies the FRN of the Operating System in the controller.
Controller Catalog Number
Address
S:60
Data Format
ASCII
Range
“A” to “ZZ”
Type
status
User Program Access
read only
This register identifies the Catalog Number for the controller.
Controller Series
Address
S:61
Data Format
ASCII
Range
A to Z
Type
status
User Program Access
read only
This register identifies the Series of the controller.
Controller Revision
Address
S:62
Data Format
word
Range
0 to 32,767
Type
status
User Program Access
read only
This register identifies the revision (Boot FRN) of the controller.
G-24
System Status File
User Program Functionality Type
Address
S:63
Data Format
word
Range
0 to 32,767
Type
status
User Program Access
read only
This register identifies the level of functionality of the user program in the controller.
Compiler Revision - Build Number
Address
S:64 (low byte)
Data Format
byte
Range
0 to 255
Type
status
User Program Access
read only
This register identifies the Build Number of the compiler which created the program
in the controller.
Compiler Revision - Release
Address
S:64 (high byte)
Data Format
byte
Range
0 to 255
Type
status
User Program Access
read only
This register identifies the Release of the compiler which created the program in the
controller.
G-25
MicroLogix 1500 Programmable Controllers User Manual
G-26
Glossary
Glossary
The following terms are used throughout this manual. Refer to the Allen-Bradley
Industrial Automation Glossary, Publication Number AG-7.1, for a complete guide to
Allen-Bradley technical terms.
address: A character string that uniquely identifies a memory location. For example,
I:1/0 is the memory address for the data located in the Input file location word1, bit 0.
AIC+ Advanced Interface Converter: a device that provides a communication link
between various networked devices. (Catalog Number 1761-NET-AIC.)
application: 1) A machine or process monitored and controlled by a controller. 2)
The use of computer- or processor-based routines for specific purposes.
backup data: Data downloaded with the program.
baud rate: The speed of communication between devices. All devices must
communicate at the same baud rate on a network.
bit: The smallest storage location in memory that contains either a 1 (ON) or a 0
(OFF).
block diagrams: A schematic drawing.
Boolean operators: Logical operators such as AND, OR, NAND, NOR, NOT, and
Exclusive-OR that can be used singularly or in combination to form logic statements
or circuits. Can have an output response be true or false.
branch: A parallel logic path within a rung of a ladder program.
communication scan: A part of the controller’s operating cycle. Communication
with other devices, such as software running on a personal computer, takes place.
controller: A device, such as a programmable controller, used to monitor input
devices and control output devices.
controller overhead: An internal portion of the operating cycle used for
housekeeping and set-up purposes.
control profile: The means by which a controller determines which outputs turn on
under what conditions.
glossary-1
MicroLogix 1500 Programmable Controllers User Manual
counter: 1) An electro-mechanical relay-type device that counts the occurrence of
some event. May be pulses developed from operations such as switch closures,
interruptions of light beams, or other discrete events.
2) In controllers a software counter eliminates the need for hardware counters. The
software counter can be given a preset count value to count up or down whenever the
counted event occurs.
CPU (Central Processing Unit): The decision-making and data storage section of a
programmable controller.
data table: The part of the processor memory that contains I/O values and files where
data is monitored, manipulated, and changed for control purposes.
DIN rail: Manufactured according to Deutsche Industrie Normenausshus (DIN)
standards, a metal railing designed to ease installation and mounting of your
controller.
download: Data is transferred from a programming or storage device to another
device.
DTE (Data Terminal Equipment): Equipment that is attached to a network to send
or receive data, or both.
EMI: Electromagnetic interference.
encoder: 1) A rotary device that transmits position information. 2) A device that
transmits a fixed number of pulses for each revolution.
executing mode: Any run or test mode.
false: The status of an instruction that does not provide a continuous logical path on a
ladder rung.
FIFO (First-In-First-Out): The order that data is entered into and retrieved from a
file.
file: A collection of information organized into one group.
full-duplex: A bidirectional mode of communication where data may be transmitted
and received simultaneously (contrast with half-duplex).
half-duplex: A communication link in which data transmission is limited to one
direction at a time.
glossary-2
Glossary
hard disk: A storage area in a personal computer that may be used to save processor
files and reports for future use.
high byte: Bits 8-15 of a word.
input device: A device, such as a push button or a switch, that supplies signals
through input circuits to the controller.
inrush current: The temporary surge current produced when a device or circuit is
initially energized.
instruction: A mnemonic and data address defining an operation to be performed by
the processor. A rung in a program consists of a set of input and output instructions.
The input instructions are evaluated by the controller as being true or false. In turn,
the controller sets the output instructions to true or false.
instruction set: The set of general purpose instructions available with a given
controller.
I/O (Inputs and Outputs): Consists of input and output devices that provide and/or
receive data from the controller.
jump: Change in normal sequence of program execution, by executing an instruction
that alters the program counter (sometimes called a branch). In ladder programs a
JUMP (JMP) instruction causes execution to jump to a labeled rung.
ladder logic: A program written in a format resembling a ladder-like diagram. The
program is used by a programmable controller to control devices.
least significant bit (LSB): The digit (or bit) in a binary word (code) that carries the
smallest value of weight.
LED (Light Emitting Diode): Used as status indicator for processor functions and
inputs and outputs.
LIFO (Last-In-First-Out): The order that data is entered into and retrieved from a
file.
low byte: Bits 0-7 of a word.
logic: A process of solving complex problems through the repeated use of simple
functions that can be either true or false. General term for digital circuits and
programmed instructions to perform required decision making and computational
functions.
glossary-3
MicroLogix 1500 Programmable Controllers User Manual
Master Control Relay (MCR): A mandatory hardwired relay that can be
de-energized by any series-connected emergency stop switch. Whenever the MCR is
de-energized, its contacts open to de-energize all application I/O devices.
mnemonic: A simple and easy to remember term that is used to represent a complex
or lengthy set of information.
modem: Modulator/demodulator. Equipment that connects data terminal equipment
to a communication line.
modes: Selected methods of operation. Example: run, test, or program.
negative logic: The use of binary logic in such a way that “0” represents the voltage
level normally associated with logic 1 (for example, 0 = +5V, 1 = 0V). Positive is
more conventional (for example, 1 = +5V, 0 = 0V).
network: A series of stations (nodes) connected by some type of communication
medium. A network may be made up of a single link or multiple links.
nominal input current: The current at nominal input voltage.
normally closed: Contacts on a relay or switch that are closed when the relay is
de-energized or the switch is deactivated; they are open when the relay is energized or
the switch is activated. In ladder programming, a symbol that will allow logic
continuity (flow) if the referenced input is logic “0” when evaluated.
normally open: Contacts on a relay or switch that are open when the relay is
de-energized or the switch is deactivated. (They are closed when the relay is
energized or the switch is activated.) In ladder programming, a symbol that will allow
logic continuity (flow) if the referenced input is logic “1” when evaluated.
off-delay time: The OFF delay time is a measure of the time required for the
controller logic to recognize that a signal has been removed from the input terminal of
the controller. The time is determined by circuit component delays and by any filter
adjustment applied.
offline: Describes devices not under direct communication.
offset: The steady-state deviation of a controlled variable from a fixed point.
glossary-4
Glossary
off-state leakage current: When an ideal mechanical switch is opened (off-state) no
current flows through the switch. Practical semiconductor switches, and the transient
suppression components which are sometimes used to protect switches, allow a small
current to flow when the switch is in the off state. This current is referred to as the offstate leakage current. To ensure reliable operation, the off-state leakage current rating
of a switch should be less than the minimum operating current rating of the load that
is connected to the switch.
on-delay time: The ON delay time is a measure of the time required for the controller
logic to recognize that a signal has been presented at the input terminal of the
controller.
one-shot: A programming technique that sets a bit for only one program scan.
online: Describes devices under direct communication. For example, when RSLogix
500 is monitoring the program file in a controller.
operating voltage: For inputs, the voltage range needed for the input to be in the On
state. For outputs, the allowable range of user-supplied voltage.
output device: A device, such as a pilot light or a motor starter coil, that receives
data from the controller.
processor: A Central Processing Unit. (See CPU.)
processor file: The set of program and data files used by the controller to control
output devices. Only one processor file may be stored in the controller at a time.
program file: The area within a processor file that contains the ladder logic program.
program mode: When the controller is not executing the processor file and all
outputs are de-energized.
program scan: A part of the controller’s operating cycle. During the scan the ladder
program is executed and the Output data file is updated based on the program and the
Input data file.
programming device: Executable programming package used to develop ladder
diagrams.
protocol: The packaging of information that is transmitted across a network.
read: To acquire data from a storage place. For example, the processor READs
information from the input data file to solve the ladder program.
glossary-5
MicroLogix 1500 Programmable Controllers User Manual
relay: An electrically operated device that mechanically switches electrical circuits.
relay logic: A representation of the program or other logic in a form normally used
for relays.
restore: To download (transfer) a program from a personal computer to a controller.
reserved bit: A status file location that the user should not read or write to.
retentive data: Information associated with data files (timers, counters, inputs, and
outputs) in a program that is preserved through power cycles.
RS-232: An EIA standard that specifies electrical, mechanical, and functional
characteristics for serial binary communication circuits. A single-ended serial
communication interface.
run mode: This is an executing mode during which the controller scans or executes
the ladder program, monitors input devices, energizes output devices, and acts on
enabled I/O forces.
rung: Ladder logic is comprised of a set of rungs. A rung contains input and output
instructions. During Run mode, the inputs on a rung are evaluated to be true or false.
If a path of true logic exists, the outputs are made true. If all paths are false, the
outputs are made false.
save: To upload (transfer) a program stored in memory from a controller to a
personal computer; OR to save a program to a computer hard disk.
scan time: The time required for the controller to execute the instructions in the
program. The scan time may vary depending on the instructions and each
instruction’s status during the scan.
sinking: A term used to describe current flow between an I/O device and controller
I/O circuit — typically, a sinking device or circuit provides a path to ground, low, or
negative side of power supply.
sourcing: A term used to describe current flow between an I/O device and controller
I/O circuit — typically, a sourcing device or circuit provides a path to the source,
high, or positive side of power supply.
status: The condition of a circuit or system, represented as logic 0 (OFF) or 1 (ON).
terminal: A point on an I/O module that external I/O devices, such as a push button
or pilot light, are wired to.
glossary-6
Glossary
throughput: The time between when an input turns on and the corresponding output
turns on.
true: The status of an instruction that provides a continuous logical path on a ladder
rung.
upload: Data is transferred to a programming or storage device from another device.
watchdog timer: A timer that monitors a cyclical process and is cleared at the
conclusion of each cycle. If the watchdog runs past its programmed time period, it
will cause a fault.
workspace: The main storage available for programs and data and allocated for
working storage.
write: To copy data to a storage device. For example, the processor WRITEs the
information from the output data file to the output modules.
glossary-7
MicroLogix 1500 Programmable Controllers User Manual
glossary-8
Index
Index
A
ADD, 15-4
address, glossary-1
AIC+
applying power to, 4-18
attaching to the network, 4-18
connecting, 4-12
isolated modem, 4-5
installing, 4-18
recommended user supplied
components, 4-17
selecting cable, 4-13
AIC+ Advanced Interface Converter,
glossary-1
Allen-Bradley
contacting for assistance, C-14
AllenBradley
contacting for assistance, P-3
AllenBradley Support, P-3
AND, 17-3
application, glossary-1
attach and lock module, 2-25
B
backup data, glossary-1
Base Comms Door, B-7
base comms door, B-7
base terminal door, B-6, B-6
base unit panel mounting, 2-17
base units
hardware overview, 1-2
baud rate, glossary-1
bit, glossary-1
bit key, 7-4
Bit Mode, 7-12
block diagrams, glossary-1
Boolean operators, glossary-1
branch, glossary-1
BSL, 19-5
BSR, 19-7
C
cables
hardware overview, 1-5
planning routes for DH485
connections, D-13
selection guide for the AIC+, 4-13
selection guide for the DeviceNet
network, 4-20
calling Allen-Bradley for assistance, C14
CE mark, 2-2
channel configuration
DF1 full-duplex, D-2
CIF table footnote, 25-8
clearing faults, C-5
CLR, 15-6
Common Techniques Used in this
Manual, P-3
communication
DeviceNet, 4-20
Communication Instructions, 25-1
communication protocols
DF1 fullduplex, D-2
DF1 halfduplex, D-4
DH485, D-10
communication scan, glossary-1
compact I/O
attach and lock module, 2-25
installing, 2-25
Compare Instructions, 1
component descriptions, 1-2
accessories
cables, 1-5
programming, 1-5
base units, 1-2
Index-1
MicroLogix 1500 Programmable Controllers User Manual
data access tool, 1-3
end cap, 1-4
expansion I/O, 1-4
memory modules/real-time clock,
1-3
processor, 1-3
components
installing, 2-18
Connecting the DF1 Protocol, 4-3
connecting the system, 4-1
AIC+, 4-12
DeviceNet network, 4-20
DF1 fullduplex protocol, 4-3
DH485 network, 4-8
Connecting to a DH–485 Network, 4-8
contacting AllenBradley for assistance,
P-3
contactors (bulletin 100), surge
suppressors for, 3-6
control profile, glossary-1
controller, glossary-1
determining faults, C-2
fault messages, C-6
features, 1-1
grounding, 3-7
installation, 2-1
mounting, 2-14
preventing excessive heat, 2-8
status file, G-1
troubleshooting, C-2
controller error recovery model, C-4
controller faults, C-2
controller LED status, C-2
controller operation
normal, C-3
controller overhead, glossary-1
Conversion Instructions, 16-1
Convert from BCD (FRD)
example, 16-8
Convert to BCD (TOD)
changes to the math register, 16-11
example, 16-12
Index-2
COP, 19-2
counter, glossary-2
CPU (Central Processing Unit),
glossary-2
CTD, 13-10
CTU, 13-10
D
DAT
Communication Errors, 7-15
configuration, 7-6
Controller Faults Displayed, 7-14
display, 7-11
Error Conditions, 7-15
Internal Errors, 7-15
keypad, 7-4
power-up operation, 7-5
DAT Feature/Function Table, 7-4
DAT Function File, 7-6
data access tool
hardware overview, 1-3
installing, 2-21
data table, glossary-2
DCD, 16-3
DeviceNet Communications, 4-20
DeviceNet network
connecting, 4-20
selecting cable, 4-20
DF1 fullduplex protocol
configuration parameters, D-2
connecting, 4-3
description, D-2
example system configuration, D-3
using a modem, 4-4, D-8
DF1 Half-Duplex protocol
configuration parameters, D-5
DF1 halfduplex protocol
description, D-4
DH485 communication protocol
configuration parameters, D-11
DH485 network
Index
configuration parameters, D-15
connecting, 4-8
description, D-10
devices that use the network, D-11
example system configuration, D16
installation, 4-8
planning considerations, D-13
protocol, D-10
token rotation, D-10
DIN rail, glossary-2
mounting, 2-15
removing your base unit, 2-16
disconnecting main power, 2-5
DIV, 15-5
download, glossary-2
DTE (Data Terminal Equipment),
glossary-2
E
Electronics Industries Association (EIA),
D-1
electrostatic discharge
preventing, 2-18
EMC Directive, 2-2
emergency-stop switches, 2-10
EMI, glossary-2
ENC, 16-4
encoder, glossary-2
END, 21-5
end cap
hardware overview, 1-4
ENTER key, 7-4
EQU, 3
error recovery model, C-4
error table, C-3
errors
controller, C-3
hardware, C-3
identifying, C-5
ESC key, 7-4
European Union Directive compliance,
2-2
executing mode, glossary-2
expansion I/O
hardware overview, 1-4
F
F1 Functions, 7-13
F1 key, 7-4
F2 Functions, 7-13
F2 key, 7-4
false, glossary-2
Fault Messages, C-6
fault recovery procedure, C-5
fault routine, C-5
fault routines, 23-6
faults
automatically clearing, C-5
identifying, C-5
manually clearing using the fault
routine, C-5
FET output specifications
1764-28BXB, A-5
FFL, 19-9
FFU, 19-12
FIFO (First-In-First-Out), glossary-2
file, glossary-2
File Instructions, 19-1
FLL, 19-3
FRD, 16-6
FRD Source Operand, 16-7
full-duplex, glossary-2
G
general specifications, A-2
GEQ, 5
grounding the controller, 3-7
GRT, 4
Index-3
MicroLogix 1500 Programmable Controllers User Manual
power considerations, 2-6
H
Index-4
half-duplex, glossary-2
hard disk, glossary-3
hardware
features, 1-1
heat protection, 2-8
high byte, glossary-3
HSL, 9-29
J
I
keypad, 7-4
I/O (Inputs and Outputs), glossary-3
identifying controller faults, C-5
IIM, 22-2
Input and Output Instructions, 10-1, 221
input device, glossary-3
input specifications, A-2
input states on power down, 2-7
inrush current, glossary-3
installing
your controller, 2-1
installing controller components, 2-18
compact I/O, 2-25
data access tool, 2-21
memory module/real-time clock, 223
processor, 2-19
installing your base unit
on DIN rail, 2-16
using mounting screws, 2-17
instruction, glossary-3
Instruction Descriptions, 11-2
instruction set, glossary-3
INT, 23-7
integer key, 7-4
Integer Mode, 7-12
IOM, 22-4
isolated link coupler
installing, 4-9
isolation transformers
L
JMP, 21-2
JSR, 21-3
jump, glossary-3
K
ladder logic, glossary-3
LBL, 21-2
least significant bit (LSB), glossary-3
LED (Light Emitting Diode), glossary-3
LEDs
error with controller, C-3
normal controller operation, C-2
status, C-2
LEQ, 5
LES, 4
LFL, 19-15
LFU, 19-18
LIFO (Last-In-First-Out), glossary-3
LIM, 8
lithium battery (1747-BA)
disposing, B-5
handling, B-2
installing, B-4
manufacturer, B-5
storing, B-2
transporting, B-3
local data types footnote, 25-29
logic, glossary-3
Logical Instructions, 17-1
Logical Instructions - Status Updates,
15-3, 17-2
low byte, glossary-3
Index
M
manuals
related, P-2
master control relay, 2-8
Master Control Relay (MCR), glossary4
master control relay circuit
periodic tests, 2-6
Math Instructions, 15-1
MCR, 21-6
memory module
data file protection, 8-4
program compare, 8-4
program/data backup, 8-4
removal/installation under power,
8-1, 8-5
Memory Module Information File, 8-5
fault override, 8-7
functionality type, 8-6
load always, 8-8
load on error, 8-8
mode behavior, 8-8
module present, 8-7
program compare, 8-8
write protect, 8-7
memory module/real-time clock
installing, 2-23
Memory Usage and Instruction
Execution Time, F-1, G-1
MEQ, 6
mnemonic, glossary-4
modem, glossary-4
modem cable
constructing your own, 4-5
modems
dialup phone, D-8
leasedline, D-9
line drivers, D-9
radio, D-9
using with MicroLogix controllers,
D-8
modes, glossary-4
monitoring
controller operation
fault recovery procedure, C-5
motor starters (bulletin 509)
surge suppressors, 3-6
motor starters (bulletin 709)
surge suppressors, 3-6
mounting
the controller, 2-14
using DIN rail, 2-15
MOV, 18-2
Move Instructions, 18-1
MUL, 15-5
MVM, 18-4
N
NEG, 15-6
negative logic, glossary-4
NEQ, 3
network, glossary-4
nominal input current, glossary-4
normally closed, glossary-4
normally open, glossary-4
NOT, 17-6
null modem cable, 4-6
O
offline, glossary-4
offset, glossary-4
off-state leakage current, glossary-5
one-shot, glossary-5
online, glossary-5
ONS, 12-7
operating voltage, glossary-5
OR, 17-4
OSF, 12-8
OSR, 12-8
OTE, 12-4
OTL, 12-5
OTU, 12-5
Index-5
MicroLogix 1500 Programmable Controllers User Manual
output device, glossary-5
output specifications, A-4
1764-28BXB FET, A-5
ownership timeout, D-7
P
panel mounting
base unit, 2-17
planning considerations for a network,
D-13
power considerations
input states on power down, 2-7
isolation transformers, 2-6
loss of power source, 2-7
other line conditions, 2-7
overview, 2-6
power supply inrush, 2-6
power distribution, 2-5
Power Save Timeout, 7-6, 7-10
power source
loss of, 2-7
Power Supply Inrush, 2-6
power supply inrush
power considerations, 2-6
preventing excessive heat, 2-8
proceessor
hardware overview, 1-3
Process Control Instruction, 24-1
processor, glossary-5
installing, 2-18
Processor Access Door, B-6
processor access door, B-6
Processor Comms Door, B-7
processor file, glossary-5
Program Control Instructions, 21-1
program faults
determining, C-2
program file, glossary-5
program mode, glossary-5
program scan, glossary-5
programming device, glossary-5
Index-6
programming the controller
overview, 1-5
Proportional Integral Derivative
instruction (PID)
application notes, 24-22
PID tuning, 24-26
runtime errors, 24-19
the PID concept, 24-1
the PID equation, 24-2
PROTECTED indicator light, 7-4, 7-11
protocol, glossary-5
PTO, 10-1
publications
related, P-2
Purpose of this Manual, P-1
PWM, 10-20
Q
quadrature encoder, 9-22
R
RAC, 9-31
read, glossary-5
real time clock
battery low indicator bit, 8-3
disabling, 8-3
Real Time Clock Function File, 8-2
REF, 22-6
related publications, P-2
relay, glossary-6
relay contact rating table, A-4
relay logic, glossary-6
relays
surge suppressors for, 3-6
Relay-Type (Bit) Instructions, 12-1
remote packet support, D-19
replacement battery, B-2
disposing, B-5
handling, B-2
installing, B-4
storing, B-2
Index
transporting, B-3
replacement doors, B-6
base comms door, B-7
base terminal door, B-6
processor access door, B-6
trim pots/mode switch cover door,
B-7
replacement kits, B-1
replacement parts, B-1
base comms door, B-7
base terminal door, B-6
processor access door, B-6
terminal blocks, B-8
trim pots/mode switch cover door,
B-7
Replacement Terminal Blocks, B-8
replacement terminal blocks, B-8
RES, 13-11
reserved bit, glossary-6
response times for high-speed dc
inputs, A-3
response times for normal dc inputs, A4
restore, glossary-6
RET, 21-4
retentive data, glossary-6
RS–232, glossary-6
RS-232 communication interface, D-1
RTO, 13-6
run mode, glossary-6
rung, glossary-6
S
safety circuits, 2-5
safety considerations
disconnecting main power, 2-5
periodic tests of master control relay
circuit, 2-6
power distribution, 2-5
safety circuits, 2-5
save, glossary-6
SBR, 21-3
scan time, glossary-6
SCL, 15-7
SCP, 15-8
Sequencer Instructions, 20-1
sinking, glossary-6
sinking and sourcing circuits, 3-8
sinking wiring diagram
1764-24BWA, 3-10
1764-28BXB, 3-12
sourcing, glossary-6
sourcing wiring diagram
1764-24BWA, 3-11
1764-28BXB, 3-13
spade lug wiring, 3-3
specifications, A-1
general, A-2
input, A-2
output, A-4
relay contact rating table, A-4
response times for high-speed dc
inputs, A-3
response times for normal dc inputs,
A-4
working voltage (1764-24AWA), A6
working voltage (1764-24BWA), A7
working voltage (1764-28BXB), A-8
SQC, 20-2
SQL, 20-10
SQO, 20-6
SQR, 15-10
status, glossary-6
status file
overview, G-1
STS, 23-8
SUB, 15-4
surge suppressors
for contactor, 3-6
for motor starters, 3-6
for relays, 3-6
Index-7
MicroLogix 1500 Programmable Controllers User Manual
recommended, 3-6
using, 3-4
SUS, 21-4
system configuration
DH485 connection examples, D-16
system connection, 4-1
T
Target Bit File, 7-6, 7-8
Target Integer File, 7-6
terminal, glossary-6
throughput, glossary-7
Timer and Counter Instructions, 13-1
TND, 21-5
TOD, 16-10
TOD Destination Operand, 16-11
TOF, 13-5
TON, 13-4
Transient Pulse Function, 3-15
Trim Pot Information Function File, 7-2
trim pots, 7-1– 7-2
adjustment, 7-2
error conditions, 7-2
location, 7-1
trim pots/mode switch cover door, B-7
troubleshooting
automatically clearing faults, C-5
contacting Allen-Bradley for
assistance, C-14
contacting AllenBradley for
assistance, P-3
controller error recovery model, C-4
determining controller faults, C-2
identifying controller faults, C-5
manually clearing faults, C-5
understanding the controller LED
status, C-2
using the fault routine, C-5
true, glossary-7
Index-8
U
UID, 23-9
UIE, 23-10
UIF, 23-12
upload, glossary-7
User Interrupt Instructions, 23-1
Using Expansion I/O, 5-1
Using Logical Instructions, 17-1
W
wire requirements, 3-1
wiring
spade lug, 3-3
wiring diagrams, 3-8
wiring recommendation, 3-2
wiring your controller, 3-1
Working Screen Operation, 7-14
working voltage (1764-24AWA)
specifications, A-6
working voltage (1764-24BWA)
specifications, A-7
working voltage (1764-28BXB)
specifications, A-8
workspace, glossary-7
write, glossary-7
X
XIC, 12-2
XIO, 12-2
XOR, 17-5
Publication 1764-6.1 - February 1999
© (1999) Rockwell International Corporation. Printed in the U.S.A.
">