5700 GPS Receiver
Engineering and Construction
Connecting and Setting Up a Nokia 6210/6250
Mobile Phone with a 5700 GPS Receiver
This document describes how you can configure and set up a Nokia (6210 or 6250 GSM) mobile phone to work as a rover with a 5700 GPS receiver; using Trimble Survey Controller™.
To connect the Nokia phone to the 5700 GPS receiver, you need to create a cable that lets you communicate with the phone.
Equipment
You will need the following equipment:
•
5700 Rover kit
•
Nokia 6210 or a Nokia 6250 GSM module (SIM card needs to be opened for data)
•
Nokia cable (Type DLR-3P)
•
Lemo 7p Digital CBL Assy, P/N:37780-00
•
DB9 male connector
Procedure
1. Make the cable between the 5700 GPS receiver and the Nokia mobile phone. This can be done by using a Lemo 7p Digital CBL Assy, P/N:37780-00 rev A cable, which has a 7pin Lemo connector in one end and open wires in the other end.
2. Solder the following wires to the DB9 Male connector:
•
Orange wire to pin 3
•
Yellow wire to pin 2
•
Brown wire to pin 5
•
Short pin 4 and 6
•
Short pin 7 and 8
Alternatively, if you have a 7-pin lemo connector and a DB9 male connector, you can
Create the same cable with this diagram:
Lemo 7 pin DB9 Male
Pin 3 Tx------------------------------------------------Pin 3
Pin 7 Rx------------------------------------------------Pin 2
Pin 1 GND---------------------------------------------Pin 5
Pin 4 --- Pin 6
Pin 7 --- Pin 8
Engineering and
Construction Division
5475 Kellenburger Road
Dayton, Ohio 45424-1099
U.S.A.
Ph: (937) 233-8921
Fax: (937) 233-9441 www.trimble.com
© Copyright January 2002, Trimble Navigation Limited. All rights reserved. The Globe & Triangle logo, Trimble, and
Trimble Survey Controller are trademarks of Trimble Navigation Limited. All other trademarks are the property of their respective owners. This document is for informational purposes only. Trimble makes no warranties, expressed or implied, in this document.
Page 1 of 3
3. Connect the new cable to the Nokia DLR-3P. Connect the Lemo end of this cable to the
5700 Port 3, and the other end of the cable to the Nokia phone. In Survey Controller, the configuration for the Rover Radio is as follows:
4. Save your settings and exit the Configuration menu.
Operation
1. You are now ready to start your survey. Go to the survey menu and choose your Survey
Style. As soon as you click Start Survey , the following screen should appear:
Note –You should see the dialed number on the phone itself.
Engineering and
Construction Division
5475 Kellenburger Road
Dayton, Ohio 45424-1099
U.S.A.
Ph: (937) 233-8921
Fax: (937) 233-9441 www.trimble.com
© Copyright January 2002, Trimble Navigation Limited. All rights reserved. The Globe & Triangle logo, Trimble, and
Trimble Survey Controller are trademarks of Trimble Navigation Limited. All other trademarks are the property of their respective owners. This document is for informational purposes only. Trimble makes no warranties, expressed or implied, in this document.
Page 2 of 3
2. The next screens should look like this:
3. You are now connected and can start your survey.
Note – If you have problems connecting to the phone, make sure that you are using the correct base telephone number and that your cable has been correctly wired. If the phone locks up, end the survey, and restart the phone.
Engineering and
Construction Division
5475 Kellenburger Road
Dayton, Ohio 45424-1099
U.S.A.
Ph: (937) 233-8921
Fax: (937) 233-9441 www.trimble.com
© Copyright January 2002, Trimble Navigation Limited. All rights reserved. The Globe & Triangle logo, Trimble, and
Trimble Survey Controller are trademarks of Trimble Navigation Limited. All other trademarks are the property of their respective owners. This document is for informational purposes only. Trimble makes no warranties, expressed or implied, in this document.
Page 3 of 3
