advertisement
Industrial IEEE 802.3at/af
Gigabit PoE+ Injector
IPOE-162
User’s Manual
Table of Contents
1. Package Content ....................................................................... 3
2. Product Features ....................................................................... 4
3. Product Specification ................................................................. 6
4 Hardware Description ................................................................. 8
4.1 Physical Dimension ............................................................. 8
4.2 Product Outlook .................................................................. 9
4.3 Industrial PoE+ Injector Upper Panel ...................................10
4.4 Wiring the Power Inputs .....................................................10
4.5 Wiring the Fault Alarm Contact ...........................................12
5. Mounting Installation ................................................................13
5.1 DIN-Rail Mounting..............................................................13
5.2 Remove DIN-Rail Mounting .................................................14
5.3 Wall Mount Plate Mounting .................................................15
6. Hardware Installation ................................................................16
Customer Support ..........................................................................19
1. Package Content
Thank you for purchasing PLANET Industrial IEEE 802.3at High Power over Ethernet Injector, IPOE-162. Terms of “802.3at PoE+ Injector” in following section of this User’s Manual means the IPOE-162.
Upon open the box of the Industrial IEEE 802.3at High Power over
Ethernet Injector and carefully unpack it. The box should contain the following items:
IPOE-162:
l
Industrial IEEE 802.3at Gigabit High Power over Ethernet Injector x 1 l
User’s Manual x 1 l
DIN Rail Kit x 1 l
Wall Mount Kit x 1 l
Dusty cap x 2
If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
3
2. Product Features
Interface l 2-Port RJ-45 interfaces
1-Port Data + Power output
1-Port Data input
Range: 24 ~ 48V DC / 24V AC redundant power.
PoE l Gigabit High Power over Ethernet Mid-Span PSE l IEEE 802.3at / 802.3af PoE compliant l IEEE 802.3at / 802.3af splitter devices compatible l Support PoE Power up to 30 Watts for PoE port l Provides DC 56V power over RJ-45 Ethernet cable to device with
Ethernet port l Auto-detect of PoE IEEE 802.3at / 802.3af equipment and devices from being damaged by incorrect installation l Remote power feeding up to 100m
Hardware l IP30 Slim Type Metal Case l LED indicators for Power LED and PoE In-Use
4
Industrial Case / Installation l DIN Rail and Wall Mount Design l Supports EFT protection 6000 VDC for power line l Supports 6000 VDC Ethernet ESD protection l -40 to 75 Degree C operation temperature
Note
PD (Powered Device) is a PoE-enabled terminal by PSE and thus consumes energy, such as IP Phones, network cameras and Wireless access points, etc.
PSE (Power Sourcing Equipment) is a device (switch, or hub for instance) that will provide power in a PoE setup. Maximum allowed continuous output power per such device in IEEE 802.3af is 15.4W, 30W in IEEE
802.3at.
5
3. Product Specification
Product
Hardware Specification
Interface
"Data" Input Port 1 x RJ-45 STP
"PoE (Data+Power)"
Output Port
1 x RJ-45 STP
Input power terminal block
1
IPOE-162
LED Indicator
System: Power 1, Power 2, Fault (Green)
PoE Port: PoE In-Use x 1 (Green)
Network Cable
Data Rate
Dimension (W x D x H)
Weight
Unit Input Voltage
Power Consumption
Number of device can be powered
Installation
10Base-T:
UTP Cat. 3, 4, 5, up to 100m (328ft)
100Base-TX:
UTP Cat. 3, 4, 5, up to 100m (328ft)
1000Base-T:
UTP Cat. 5, 5e, 6 up to 100m (328ft)
EIA/TIA- 568 100-ohm STP (100m)
10/100/1000Mbps
135 x 97 x 32 mm
473g
24 ~ 48V DC
24V AC
30 Watts max.
1
Alarm
Enclosure
DIN Rail kit and Wall Mount ear
Provides one relay output for power fail,
Alarm Relay current carry ability: 3A @
DC 30V
IP30 Slim Type Metal Case
6
Power over Ethernet
PoE Standard
PoE Power Output
PoE Power supply Type
Power Pin Assignment
Standards Conformance
Standards Compliance
FCC
CE
Stability Testing
Environment
EMI
EMS
Operating Temperature
Storage Temperature
Humidity
IEEE 802.3at High Power over Ethernet
/ Mid-Span PSE
DC 56V / 30 Watts
Mid-Span
4/5(+), 7/8(-)
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit
Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet enhancement standard
FCC Part 15B Class A
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2 (ESD)
EN 61000-4-3 (RS)
EN 61000-4-4 (EFT)
EN 61000-4-5 (Surge)
EN 61000-4-6 (CS)
EN 61000-4-8 (PFMF)
IEC60068-2-32 (Free fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
-40 ~ 75 Degree C
-40 ~ 85 Degree C
5 ~ 95% (Non-condensing)
7
4 Hardware Description
4.1 Physical Dimension
Bottom View Front View
P1 P2 FAULT
10/100/1000T
Ethernet
10/100/1000T
PoE
In-Use
Ethernet+DC
802.3at
IPOE-162
Top View Rear View
Side View Mounting Kit DIN-Rail Kit Mounting Kit
Figure 4-1
8
4.2 Product Outlook
P1 P2 FAULT
10/100/1000T
Ethernet
10/100/1000T
PoE
In-Use
Ethernet+DC
802.3at
IPOE-162
Figure 4-2
LED Indicators
LED
P1
P2
FAULT
PoE In-Use
Color Function
Green Indicate the power 1 has power.
Green Indicate the power 2 has power.
Green
Indicate the either power 1 or power 2 has no power.
Green
Indicate the port is providing 56V DC in-line power.
9
4.3 Industrial PoE+ Injector Upper Panel
The upper panel of the Industrial PoE+ Injector consist one terminal block connector within two DC / AC power inputs. Figure 1 shows the upper panel of the Industrial PoE+ Injector.
1 2 3 4 5 6
Figure 1: Industrial PoE+ Injector Upper Panel.
4.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial
PoE+ Injector is used for two DC / AC redundant powers input. Please follow the steps below to insert the power wire.
10
1. Insert Positive / Negative DC power wires or Neutral / Line AC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER
2.
1 2 3 4 5 6
Figure 2: Power input PINs.
2. Tighten the wire-clamp screws for preventing the wires from loosing.
1 2
Power 1
+
3
Fault
4 5
-
6
Power 2
+
Figure 3: PWR1 & PWR2 Pin of Terminal Block.
Note
The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG.
11
4.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the
Industrial PoE+ Injector will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.
Insert the wires into the fault alarm contacts
Figure 4: Fault Pin of Terminal Block.
Note
1. The wire gauge for the terminal block should be in the range between 12 ~ 24 AWG.
2. Alarm relay circuit accepts up to 30V, max. 3A currents.
12
Figure 5: Fault Alarm Contact.
5. Mounting Installation
This section describes how to install the Industrial Equipment and make connections to it. Please read the following topics and perform the procedures in the order being presented.
Note
In the installation steps below, this Manual use IGS-801
(PLANET 8 Port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial slim type Switch, Industrial Media / Serial Converter and
Industrial PoE equipment are similar.
5.1 DIN-Rail Mounting
The DIN-Rail is already screwed on the Industrial Equipment. Please refer to following figures and know how to hang the Industrial
Equipment:
Step 1: Lightly press the button of DIN-Rail into the track.
1
2
Figure 6: Install Industrial Equipment in DIN-Rail mount.
13
Step 2: Check the DIN-Rail is tightly on the track.
Figure 7: Industrial Equipment installed in DIN-Rail mount.
5.2 Remove DIN-Rail Mounting
Step 1: Please refer to following procedures to remove the Industrial
Equipment from the track.
2
1
Figure 8: Remove Industrial Equipment in DIN-Rail mount.
14
Step 2: Lightly press the button of DIN-Rail for remove it from the track.
5.3 Wall Mount Plate Mounting
To install the Industrial Equipment on the wall, please follows the instructions described below.
Step 1: Remove the DIN-Rail from the Industrial Equipment; loose the screws to remove the DIN-Rail.
Step 2: Place the wall mount plate on the rear panel of the Industrial
Equipment.
Figure 9: Attach Brackets to the Industrial Equipment.
Step 3: Use the screws to screw the wall mount plate on the
Industrial Equipment.
Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial Equipment on the wall.
Step 5: To remove the wall mount plate, reverse steps above.
15
6. Hardware Installation
This Industrial IEEE 802.3at Gigabit High Power over Ethernet Injector provides three different running speeds – 10Mbps, 100Mbps and
1000Mbps in the same device and automatically distinguishes the speed of incoming connection. Please refer to following sections for detail information about Industrial IEEE 802.3at Gigabit High Power over Ethernet Injector.
Before Installation
Before your installation, it is recommended to check your network environment. If there has any IEEE 802.3at devices need to power on, the IPOE-162 can provide you a way to supply power for this Ethernet device conveniently and easily.
If there is very difficult to find a power socket for AC-DC Adapter to your Non-IEEE 802.3at networked device, the IPOE-162 with POE-162S
/ IPOE-162S can provide you a way to supply DC power for this
Ethernet device conveniently and easily.
Note
The IPOE-162 with IPOE-162S / POE-162S is installed in pair. However, the use of third-party device is allowed if the device complied with IEEE 802.3at Power over
Ethernet.
IPOE-162 Injector Installation
1. Connect the Power (Range from AC 24V or DC 24 ~ 48V) to 6-pin terminal block of IPOE-162. The power LED will be steady on.
2. Connect a standard network cable from Switch / workstation to
“Ethernet” port of IPOE-162.
3. Connect the long cable that will be used to connect to the remote device to the port “Ethernet + DC”.
4. Due to the capability of IEEE 802.3at Power over Ethernet, the IPOE-
162 can directly connect with any IEEE 802.3at / IEEE 802.3af endnodes such as PTZ (Pan, Tilt & Zoom) network cameras, PTZ Speed
Dome, color touch- screen Voice over IP (VoIP) telephones, multi- channel wireless LAN access points.
16
Power
Supply
IPOE-162 Installation
100 meters
AC 24V/DC 24~48V
Power
75 ℃
-40 ℃
Industrial
Switch
Data
IPOE-162
Data
PoE
Power
PoE
PTZ Camera
PoE
1000Base-T UTP
1000Base-T UTP with PoE
Power Line
Once IPOE-162 detects the existence of an IEEE 802.3at device, the
POE In-use LED indicator will be steady on to show it is providing power.
Note
1. Due to the IPOE-162 PoE port supports 56V DC PoE power output, please check and assure the Powered
Device (PD) acceptable DC power range is from 52 to 56V DC. Otherwise, it will damage the Powered
Device (PD).
2. If the connected device (PD) is not fully complying with IEEE 802.3at Power over Ethernet or in-line power device, the IPOE-162 might encounter incompatible issue which fails to power up the devices.
IPOE-162 and IPOE-162S, the IEEE 802.3at Injector Splitter
Installation
1. Connect the Power (Range from AC 24V or DC 24 ~ 48V) to 6-pin terminal block of IPOE-162. The power LED will be steady on.
2. Connect a standard network cable from “Ethernet+DC” port of
IPOE-162 to “PoE In” port of IPOE-162S. The POE In-use LED of
IPOE-162 / IPOE-162S will light on continuance.
17
3. Connect a standard network cable from Switch/workstation to
“Ethernet” port of IPOE-162.
4. Connect the UTP cable from “Ethernet” port of IPOE-162S to the
RJ-45 port of remote device.
5. Adjust proper DC voltage power output and connect DC plug from
“Power Output” of IPOE-162S to remote device.
6. Power on the remote device and its power LED indicator will remains on.
Power
Supply
IPOE-162 + IPOE-162S Installation
100 meters
AC 24V/DC 24~48V
Power
Industrial
Switch
Data
IPOE-162
Data
PoE
Power
75 ℃
-40 ℃
802.3at
PoE Splitter
PTZ Camera
Data
DC
Power
12V/24V DC Output
PoE
1000Base-T UTP
1000Base-T UTP with PoE
Power Line
Note
1. According to IEEE 802.3at Power over Ethernet, the
IPOE-162 will not inject power to the cable if not connecting to IEEE 802.3at devices.
2. Please ensure the output voltage is correct before applying power to remote device. Otherwise, it will damage the Powered Device (PD).
18
Customer Support
Thank you for purchase PLANET products. You can browse our online
FAQ resource at the PLANET Web site first to check if it could solve you issue. If you need more support information, please contact PLANET switch support team.
PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address : [email protected]
Copyright © PLANET Technology Corp. 2012.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
19
EC Declaration of Conformity
For the following equipment:
*Type of Product: Industrial IEEE 802.3at High Power over Ethernet Injector (30 Watts)
*Model Number: IPOE-162
* Produced by:
Manufacturer‘s Name :
Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.) is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
(Class A: 2010)
(2010)
(2008)
(2006 + A1: 2007 + A2: 2010)
(2004 + A1: 2010)
(2005)
(2008)
(2009)
Responsible for marking this declaration if the:
Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan
Place
17 Aug., 2012
Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
advertisement