advertisement
Parts Manual
RCF3096 (540 RPM)
Rotary Cutter
Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!
39799
Cover illustration may show optional equipment not supplied with standard unit.
© Copyright 2020 Printed 07/20/20 327-149P
Table of Contents
Section 1: Introduction.................................................4
Using This Manual...............................................................4
Manual Replacement Information.......................................4
Manual Revisions................................................................4
Touch-up Paint....................................................................4
Hardware Legend................................................................5
Replacement Hardware......................................................5
Serial Numbers...................................................................5
Part Number Service Coding..............................................5
Section 2: Deck..............................................................6
Deck Components...............................................................6
Section 3: Hitch & Tailwheel.........................................8
Axle Lift Hydraulic or Manual 3-Point..................................8
Axle Lift Hydraulic or Manual Pull Type/Semi-Mount.........10
Hitch 3-Point......................................................................12
Hitch Pull Type Tongue S/N D001091N-............................14
Hitch Pull Type Tongue S/N D001092N+...........................16
Hub & Spindle Assembly (331-795L)................................18
Hub Assembly (330-938K)................................................20
Hydraulic Cylinder (810-384C) Cross...............................22
Hydraulic Cylinder (850-449C) Cross...............................24
Performance Hitch.............................................................26
Swivel Hitch.......................................................................28
Tail Wheel 3-Point W/ 15" Lam. Tire..................................30
Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire.....32
Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire.....34
Transport Axle Pull Type....................................................36
Section 4: Blade Drive.................................................38
Blade Carrier CCW...........................................................38
Blade Carrier CW..............................................................40
Blade Drive 3-Point & Semi-Mount....................................42
Blade Drive Pull Type W/ Equal Angle...............................44
Blade Drive Pull Type W/CV..............................................46
Driveline 540 RPM (826-151C) Eurocardan.....................48
Driveline 540 RPM (826-255C) Eurocardan.....................50
Driveline 540 RPM (826-256C) Eurocardan.....................52
Driveline CV Pull Type Cutter 540 RPM (826-053C)
Walterscheid...............................................................54
Driveline Flex Coupler (826-224C) Eurocardan................56
Driveline Slip Clutch (1446016) Eurocardan.....................58
Driveline Slip Clutch (1446137) Eurocardan.....................60
Driveline Stub Shaft Pull Type 540 RPM (826-225C)
Eurocardan.................................................................62
Gearbox (826-722C) Comer.............................................64
Gearbox, T-Box 540 RPM (826-356C) Comer...................66
Section 5: Guards........................................................68
Guard Chain Dual Front....................................................68
Guard Chain Dual Rear.....................................................70
Guard Chain Single Front..................................................72
Guard Chain Single Rear..................................................74
Guard Rubber Front..........................................................76
Guard Rubber Rear...........................................................78
Section 6: Labels.........................................................80
Decal Placement 3-point...................................................80
Decal Placement Pull Type................................................82
Part Number Index.......................................................84
© Copyright 2020 All rights reserved Printed 07/20/20
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Great Plains Manufacturing, Incorporated Trademarks
The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
327-149P - 2 07/20/20
Alphabetized Table of Contents
A
Axle Lift Hydraulic or Manual 3-Point.............................8
Axle Lift Hydraulic or Manual Pull Type/Semi-Mount.....10
B
Blade Carrier CCW......................................................38
Blade Carrier CW.........................................................40
Blade Drive 3-Point & Semi-Mount...............................42
Blade Drive Pull Type W/ Equal Angle..........................44
Blade Drive Pull Type W/CV.........................................46
D
Decal Placement 3-point..............................................80
Decal Placement Pull Type...........................................82
Deck Components..........................................................6
Driveline 540 RPM (826-151C) Eurocardan.................48
Driveline 540 RPM (826-255C) Eurocardan.................50
Driveline 540 RPM (826-256C) Eurocardan.................52
Driveline CV Pull Type Cutter 540 RPM (826-053C)
Walterscheid..........................................................54
Driveline Flex Coupler (826-224C) Eurocardan...........56
Driveline Slip Clutch (1446016) Eurocardan................58
Driveline Slip Clutch (1446137) Eurocardan................60
Driveline Stub Shaft Pull Type 540 RPM (826-225C)
Eurocardan............................................................62
G
Gearbox (826-722C) Comer.........................................64
Gearbox, T-Box 540 RPM (826-356C) Comer..............66
Guard Chain Dual Front...............................................68
Guard Chain Dual Rear................................................70
Guard Chain Single Front.............................................72
Guard Chain Single Rear.............................................74
Guard Rubber Front.....................................................76
Guard Rubber Rear......................................................78
H
Hitch 3-Point.................................................................12
Hitch Pull Type Tongue S/N D001091N-.......................14
Hitch Pull Type Tongue S/N D001092N+......................16
Hub & Spindle Assembly (331-795L)...........................18
Hub Assembly (330-938K)...........................................20
Hydraulic Cylinder (810-384C) Cross...........................22
Hydraulic Cylinder (850-449C) Cross...........................24
P
Performance Hitch........................................................26
S
Swivel Hitch..................................................................28
T
Tail Wheel 3-Point W/ 15" Lam. Tire.............................30
Transport Axle 3-Point & Semi-Mount W/ 15" Lam.
Tire.........................................................................32
Transport Axle 3-Point & Semi-Mount W/ 21" Lam.
Tire.........................................................................34
Transport Axle Pull Type...............................................36
07/20/20 - 3 327-149P
327-149P - 4 07/20/20
07/20/20 - 5 327-149P
Deck Components
(Applies to RCF3096 only)
39802
327-149P - 6 07/20/20
Deck Components
(Applies to RCF3096 only)
Ref.
Part No.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
11.
12.
13.
14.
Dwg 33344
326-479D
326-546H81
332-014D
802-106C
802-224C
802-603C
803-037C
803-198C
803-255C
804-007C
805-088C
805-485C
816-504C
840-273C
Part Description
Drawing Image Number
SKID SHOE
DECK WELDMENT RCF3096 GREEN
RCF REFLECTOR BRACKET
RHSNB 1/2-13X1 1/2 GR5
HHCS 1/4-20X1 1/4 GR5
PLOW 3/8-16X1 GR5
NUT HEX WHIZ 1/2-13 PLT
NUT HEX WHIZ 3/8-16 PLT
NUT HEX NYLOCK 1/4-20
WASHER FLAT 1/4 SAE PLT
PIN, HAIR COTTER 3/16 WIRE DIA
PIN, HITCH 3PT CAT 1&2
MANUAL STORAGE CONTAINER
PLUG LP 3" ID RUBBER
Comments Revision
Section 2: Deck
07/20/20 - 7 327-149P
Axle Lift Hydraulic or Manual 3-Point
(Applies to RCF3096 only)
35175
327-149P - 8 07/20/20
Axle Lift Hydraulic or Manual 3-Point
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 35175
312-729D
326-494A
326-508A
326-564H
326-500H
802-017C
802-184C
802-205C
803-013C
803-026C
803-168C
803-263C
804-012C
806-184C
807-023C
850-449C
810-384C
810-818C
811-133C
811-394C
811-676C
811-676C
890-637C
15.
16.
17.
18.
10.
11.
12.
13.
14.
15.
6.
7.
8.
9.
1.
2.
3.
4.
4.
5.
19.
20.
21.
Part Description
Drawing Image Number
HOSE HOLDER BRACKET
HYDRAULIC LIFT - 3-PNT
RATCHET JACK BUNDLE
AXLE LUG 96"
AXLE LUG
HHCS 3/8-16X1 GR5
HHCS 3/4-10X1 1/2 GR5
HHCS 1-8X5 1/2 GR5
NUT LOCK 3/8-16 PLT
NUT LOCK 3/4-10 PLT
NUT HEX TOP LOCK 1-8 PLT
NUT HEX FLANGE LOCK 5/8-11 PLT
WASHER FLAT 3/8 SAE PLT
U-BOLT 5/8-11 X 4 1/32 X 5 1/2
SPRING HOSE LOOP
CYL 3X6X1.25 ROD (TIE ROD)
RPBY 850-449C
STRK CNTRL SPCRS 1.125 TO 1.50
AD 9/16MJIC 3/4MORB
CP 3/4FORB MALE QD POPPET TYPE
HH3/8R1 144 3/4MORB 9/16FJIC
HH3/8R1 144 3/4MORB 9/16FJIC
RATCHET JACK 16.25 - 22.25
Comments
15" Laminated Tire
21" Laminated Tire
S/N D001139N+
S/N D001138N-
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 9 327-149P
Axle Lift Hydraulic or Manual Pull Type/Semi-Mount
(Applies to RCF3096 only)
33453
327-149P - 10 07/20/20
Axle Lift Hydraulic or Manual Pull Type/Semi-Mount
(Applies to RCF3096 only)
Ref.
Part No.
28.
29.
30.
31.
32.
33.
34.
35.
25.
26.
27.
27.
19.
20.
21.
22.
23.
24.
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
6.
6.
7.
8.
1.
2.
3.
3.
4.
5.
803-013C
803-026C
803-147C
803-148C
803-168C
803-258C
803-263C
804-012C
804-017C
806-184C
807-023C
807-271C
850-449C
810-384C
810-818C
811-394C
811-633C
N/A
812-388C
N/A
841-284C
890-637C
Dwg 33453
312-729D
326-491A
326-492H
326-587H
326-508A
326-564H
326-912D
326-988D
330-294D
800-306C
802-017C
802-184C
802-205C
802-254C
802-269C
802-762C
Part Description
Drawing Image Number
HOSE HOLDER BRACKET
HYDRAULIC LIFT
SPRING SHOCK
SPRING SHOCK 10PT
RATCHET JACK BUNDLE
AXLE LUG 96"
TRUNNION ARM
TRUNNION ARM 10PT
SPACER TRUNNION ARM
FILL PLUG VENTED 3/4-16 PLT
HHCS 3/8-16X1 GR5
HHCS 3/4-10X1 1/2 GR5
HHCS 1-8X5 1/2 GR5
HHCS 5/8-11X5 1/2 GR5
HHCS 1/2-13X9 GR5
HHCS 1-8X6 1/2 GR8
NUT LOCK 3/8-16 PLT
NUT LOCK 3/4-10 PLT
NUT HEX NYLOCK 1/2-13
NUT HEX NYLOCK 5/8-11 PLT
NUT HEX TOP LOCK 1-8 PLT
NUT HEX FLG LOCK 1-8 GR B PLT
NUT HEX FLANGE LOCK 5/8-11 PLT
WASHER FLAT 3/8 SAE PLT
WASHER FLAT 1/2 USS PLT
U-BOLT 5/8-11 X 4 1/32 X 5 1/2
SPRING HOSE LOOP
SPRING COMP 3.20OD .63W 5.5L
CYL 3X6X1.25 ROD (TIE ROD)
RPBY 850-449C
STRK CNTRL SPCRS 1.125 TO 1.50
CP 3/4FORB MALE QD POPPET TYPE
HH3/8R1 162 3/4MORB 9/16 FJIC
SWIVEL CAST
OREL 1/16 9/16MJIC 3/4MORB
RATCHET JACK 16.25 - 22.25
Comments
Semi Mount Unit
Pull Type Unit
Semi Mount Unit
Pull Type Unit
S/N D001139N+
S/N D001138N-
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 11 327-149P
Hitch 3-Point
(Applies to RCF3096 only)
39803
327-149P - 12 07/20/20
Hitch 3-Point
(Applies to RCF3096 only)
Ref.
Part No.
31.
32.
33.
34.
35.
36.
37.
38.
39.
27.
28.
29.
30.
21.
22.
23.
24.
25.
26.
17.
18.
19.
20.
11.
12.
13.
14.
15.
16.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
802-908C
803-026C
803-028C
803-038C
803-168C
803-271C
804-025C
804-026C
804-029C
805-017C
805-088C
805-090C
805-088C
805-137C
805-485C
327-143S
802-010C
802-138C
803-177C
804-036C
807-350C
837-062C
837-063C
Dwg 33345
312-821D
312-931D
326-591D
326-891D
326-916D
326-917D
326-002D
326-947D
326-975D
326-976D
326-982D
802-057C
802-064C
802-098C
802-169C
802-205C
Part Description
Drawing Image Number
BSHG 1 1/4ODX1 1/32IDX2 1/16LG
REAR BRACE STRAIGHT LONG
HITCH MOUNT BSHG
REAR BRACE SHORT
BSHG 1OD X 11GWLX.44
REAR BRACE STRAIGHT
TUBE 1 OD X 11/16 LG. X 5/32w
REAR BRACE FORMED
HITCH STRAP LH RCF3096
HITCH STRAP RH RCF3096
TUBE RND 1 1/4ODX12GWX.84
HHCS 5/8-11X2 1/4 GR5
HHCS 3/4-10X2 GR5
HHCS 1-8X4 1/2 GR5
HHCS 1-8X3 1/2 GR5
HHCS 1-8X5 1/2 GR5
HHCS 7/8-9X2 1/2 GR5
NUT LOCK 3/4-10 PLT
NUT NY-LOK 7/8-9 PLT
NUT HEX 1-8 NYLON INSERT PLT
NUT HEX TOP LOCK 1-8 PLT
NUT HEX TOP LOCK 5/8-11 PLT
WASHER FLAT 3/4 SAE PLT
WASHER FLAT 7/8 SAE PLT
WASHER FLAT 1 SAE
PIN COTTER 3/16 X 1 3/4 PLT
PIN, HAIR COTTER 3/16 WIRE DIA
PIN CLEVIS 1 X 3 3/16 LG
PIN, HAIR COTTER 3/16 WIRE DIA
PIN CLEVIS 1 X 2 PLT
PIN, HITCH 3PT CAT 1&2
DRIVELINE HOLDER W/ HARDWARE
HHCS 5/16-18X1 1/4 GR5
HHCS 5/16-18X2 1/4 GR5
NUT HEX LOCK 5/16-18 FLG.
WASHER FLAT 5/16 SAE PLT
SPRING TORSION DRIVELINE HLDER
DRIVELINE HOOK
MOUNT DRIVELINE HOOK
Comments
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 13 327-149P
Hitch Pull Type Tongue S/N D001091N-
(Applies to RCF3096 only)
33583
327-149P - 14 07/20/20
Hitch Pull Type Tongue S/N D001091N-
(Applies to RCF3096 only)
Ref.
Part No.
12.
13.
14.
15.
8.
9.
10.
10.
11.
12.
5.
6.
6.
7.
1.
2.
3.
3.
4.
5.
16.
17.
17.
18.
19.
20.
21.
22.
803-375C
804-025C
804-028C
804-029C
804-125C
805-045C
805-109C
805-083C
805-088C
805-485C
890-118C
891-246C
Dwg 33411
312-421H
312-733D
327-123H
326-935H
326-495H
327-124K
326-937K
326-557H
326-933H
802-074C
802-096C
802-098C
803-075C
803-030C
803-168C
803-265C
Part Description
Drawing Image Number
CLEVIS WELDMENT
TUBE 1 5/8 OD X 7/32 WL X1 LG.
LEVEL ROD WLDMT OFFSET SHORT
OFFSET LEVEL ROD END, 1" THD
TONGUE WELDMENT 30/3610
LEVEL ROD ASY. 3096
OFFSET LEVEL ROD ASY, SHORT
LEVEL ROD LONG
1" LEVEL ROD, SHORT
HHCS 1-8X6 1/2 GR5
HHCS 1-8X2 1/2 GR5
HHCS 1-8X4 1/2 GR5
NUT HEX JAM 7/8-9
NUT HEX JAM 1-8 PLT
NUT HEX TOP LOCK 1-8 PLT
NUT HEX COUPLER 7/8-9 x 5
NUT HEX COUPLER 1-8 X 5
WASHER FLAT 3/4 SAE PLT
WASHER FLAT 1 USS PLT
WASHER FLAT 1 SAE
WASHER BELLEVILLE 1ID
PIN COTTER 5/32 X 1 1/4 LG
PIN COTTER 1/8 X 1 1/4 PLT
PIN CLEVIS 3/4 X 1 1/2
PIN, HAIR COTTER 3/16 WIRE DIA
PIN, HITCH 3PT CAT 1&2
SCREW JACK 2000# 14-24 TOP-WND
AG SAFETY CHAIN 6400 LB
Comments
For 7/8" leveling rod
For 1" leveling rod
7/8" leveling rod kit
1" leveling rod kit
7/8" leveling rod
1" leveling rod
For 7/8" leveling rod
For 1" leveling rod
For 7/8" leveling rod
For 1" leveling rod
For 7/8" & 1" leveling rod
For 7/8" leveling rod
For 1" leveling rod
For 7/8" & 1" leveling rod
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 15 327-149P
Hitch Pull Type Tongue S/N D001092N+
(Applies to RCF3096 only)
70102
327-149P - 16 07/20/20
Hitch Pull Type Tongue S/N D001092N+
(Applies to RCF3096 only)
Ref.
Part No.
13.
13.
14.
15.
8.
9.
10.
11.
11.
12.
5.
6.
6.
7.
1.
2.
2.
3.
4.
5.
16.
17.
18.
18.
19.
20.
21.
Dwg 70102
312-733D
326-557H
326-933H
326-889H
326-891H
327-123H
326-935H
327-124K
326-937K
802-096C
802-106C
803-020C
803-031C
803-075C
803-030C
803-168C
803-265C
803-375C
804-015C
804-025C
804-027C
804-029C
805-045C
805-109C
805-083C
890-118C
891-246C
Part Description
Image No.
TUBE 1 5/8 OD X 7/32 WL X1 LG.
LEVEL ROD LONG
1" LEVEL ROD, SHORT
TONGUE
ADJUSTABLE JACK MOUNT
LEVEL ROD WLDMT OFFSET SHORT
OFFSET LEVEL ROD END, 1" THD
LEVEL ROD ASY. 3096
OFFSET LEVEL ROD ASY, SHORT
HHCS 1-8X2 1/2 GR5
RHSNB 1/2-13X1 1/2 GR5
NUT HEX 1/2-13 PLT
NUT HEX 1-8 PLT
NUT HEX JAM 7/8-9
NUT HEX JAM 1-8 PLT
NUT HEX TOP LOCK 1-8 PLT
NUT HEX COUPLER 7/8-9X5
NUT HEX COUPLER 1-8 X 5
WASHER LOCK SPRING 1/2 PLT
WASHER FLAT 3/4 SAE PLT
WASHER LOCK SPRING 1 PLT
WASHER FLAT 1 SAE
PIN COTTER 5/32 X 1 1/4 LG
PIN COTTER 1/8 X 1 1/4 PLT
PIN CLVS .75X1.50 USBL HT
SCREW JACK 2000# 14-24 TOP-WND
AG SAFETY CHAIN 6400 LB
Comments
7/8" Leveling rod
1" Leveling rod
For 7/8" leveling rod
For 1" leveling rod
7/8" Leveling rod kit
1" Leveling rod kit
For 7/8" leveling rod
For 1" leveling rod
For 7/8" leveling rod
For 1" leveling rod
For 7/8" leveling rod
For 1" leveling rod
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 17 327-149P
Hub & Spindle Assembly (331-795L)
(Applies to RCF3096 only)
72662
327-149P - 18 07/20/20
Ref.
Part No.
Dwg 72662
331-795L
9.
10.
11.
12.
13.
14.
15.
16.
17.
5.
6.
7.
8.
1.
2.
3.
4.
200-001D
800-080C
802-099C
802-779C
803-019C
803-029C
803-310C
804-055C
805-246C
815-243C
815-491C
816-497C
822-020C
822-021C
822-033C
822-034C
HT250
Hub & Spindle Assembly (331-795L)
(Applies to RCF3096 only)
Part Description
Image No.
SPINDLE AND HUB ASSY
*
HUB GREASE CAP
GREASE ZERK 1/4-28 THD FORMING
HHCS 1/2-13X3 1/4 GR5
HUB STUD 1/2-20X1.88 GR5
NUT LOCK 1/2-13 PLT
NUT HEX SLOTTED 7/8-14 PLT
NUT HEX 1/2-20 X 5/8 HIGH
WASHER SPINDLE - 7/8
PIN COTTER 5/32 X 1 3/4 LG
HUB 5-BOLT W/CUPS/STUDS
SINGLE AXLE SPINDLE, WING
SEAL 1.75ID CR17617
BRG CUP LM-67010
BRG CONE 1.25ID LM-67048
BRG CUP LM-48510
BRG CONE LM-48548
MACHINED 5-BOLT HUB
Comments
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 19 327-149P
Hub Assembly (330-938K)
(Applies to RCF3096 only)
37676
327-149P - 20 07/20/20
Hub Assembly (330-938K)
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 37676
330-938K
9.
10.
11.
12.
13.
14.
15.
5.
6.
7.
8.
1.
2.
3.
4.
200-001D
330-938K
800-080C
802-779C
803-029C
803-310C
804-055C
805-246C
815-243C
816-497C
822-020C
822-021C
822-033C
822-034C
815-242C
Part Description
Image No.
HUB 5 BOLT COMPLETE
*
HUB GREASE CAP
HUB 5 BOLT COMPLETE
GREASE ZERK 1/4-28 THD FORMING
HUB STUD 1/2-20X1.88 GR5
NUT HEX SLOTTED 7/8-14 PLT
NUT HEX 1/2-20 X 5/8 HIGH
WASHER SPINDLE - 7/8
PIN COTTER 5/32 X 1 3/4 LG
HUB 5-BOLT W/CUPS/STUDS
SEAL 1.75ID CR17617
BRG CUP LM-67010
BRG CONE 1.25ID LM-67048
BRG CUP LM-48510
BRG CONE LM-48548
HUB 5-BOLT CASTING
Comments
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 21 327-149P
Hydraulic Cylinder (810-384C) Cross
(Applies to RCF3096 only)
72940
327-149P - 22 07/20/20
Hydraulic Cylinder (810-384C) Cross
(Applies to RCF3096 only)
Ref.
Part No.
Part Description
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
19.
20.
5.
6.
7.
8.
1.
2.
3.
4.
Dwg
810-384C
1D1205-8
N/A
N/A
N/A
1D1401-300
1D0007-850
1D0206-1075
1D1157-17
N/A
2A0235-8
N/A
2A0580-1100
2A0246-12
2A0079-616
1D1003-5
2A0235-6
805-032C
1D1551-16275
1D1551-16300
810-009C
Image No. 72940
RPBY 850-449C
*
CROSS, BASE CLEVIS
CROSS BACK UP
CROSS O-RING
CROSS CROWN SEAL
CROSS PISTON 3 BORE CYLINDER
CROSS, TUBE
CROSS, ROD
CROSS HEAD 3 BORE CYLINDER
WIPER SEAL CROSS
CROSS NUT, TIE ROD
CROSS U-CUP
CROSS TIE ROD
CROSS NUT, PISTON
CROSS SCREW, CAP
CROSS ROD CLEVIS
CROSS NUT, CLEVIS & TIE ROD
PIN HAIR COTTER .148 WIRE
CROSS CLEVIS PIN 2.75"USABLE
CROSS CLEVIS PIN 3"USABLE
CYL SEAL KIT 3 (CROSS)
Comments
Complete Assembly
Only found in seal kit item 20
Only found in seal kit item 20
Only found in seal kit item 20
Only found in seal kit item 20
Only found in seal kit item 20
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 23 327-149P
Hydraulic Cylinder (850-449C) Cross
(Applies to RCF3096 only)
74608
327-149P - 24 07/20/20
Hydraulic Cylinder (850-449C) Cross
(Applies to RCF3096 only)
Ref.
Part No.
Part Description
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
19.
20.
5.
6.
7.
8.
1.
2.
3.
4.
Dwg
850-449C
4C5853
N/A
N/A
N/A
4C4360
1D0007-812
4C2649
4C2444
N/A
2A0235-8
N/A
2A0580-1075
2A0246-12
2A0079-616
1D1013-5
2A0235-6
805-032C
1D1551-16275
1D1551-16300
850-357C
Image No. 74608
CYL 3X6X1.25 ROD (TIE ROD)
*
CROSS BASE CLEVIS
CROSS BACK UP
CROSS O-RING
CROSS CROWN SEAL
CROSS PISTON
CROSS TUBE
CROSS ROD
CROSS HEAD
WIPER SEAL CROSS
CROSS NUT, TIE ROD
CROSS U-CUP
CROSS TIE ROD
CROSS NUT, PISTON
CROSS SCREW, CAP
CROSS ROD CLEVIS
CROSS NUT, CLEVIS & TIE ROD
PIN HAIR COTTER .148 WIRE
CROSS CLEVIS PIN 2.75"USABLE
CROSS CLEVIS PIN 3"USABLE
CROSS SEAL KIT
Comments
Only found in seal kit item 20
Only found in seal kit item 20
Only found in seal kit item 20
Only found in seal kit item 20
Only found in seal kit item 20
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 25 327-149P
Performance Hitch
(Applies to RCF3096 only)
70104
327-149P - 26 07/20/20
Performance Hitch
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 70104
334-007A
5.
6.
7.
1.
2.
3.
4.
334-049H
334-050H
334-066H
802-070C
802-365C
803-019C
803-181C
Part Description
Drawing Image Number
(LPH) PERFORMANCE HTCH SLF LVL
*
HITCH SELF LEVELING 1.5D SHFT
HITCH CLEVIS SELF LEVELING
BSHG HITCH LOCK/STOP 1.56 ID
HHCS 3/4-10X6 GR5
HHCS 1/2-13X3 GR8
NUT LOCK 1/2-13 PLT
NUT HEX FLANGE LOCK 3/4-10 PLT
Comments
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 27 327-149P
Swivel Hitch
(Applies to RCF3096 only)
70103
327-149P - 28 07/20/20
Swivel Hitch
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 70103
334-006A
1.
2.
3.
4.
334-004H
334-066H
802-365C
803-019C
Part Description
Drawing Image Number
SWIVEL CLEVIS
*
SWIVEL CLEVIS STRAIGHT
BSHG HITCH LOCK/STOP 1.56 ID
HHCS 1/2-13X3 GR8
NUT LOCK 1/2-13 PLT
Comments
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 29 327-149P
Tail Wheel 3-Point W/ 15" Lam. Tire
(Applies to RCF3096 only)
33828
327-149P - 30 07/20/20
Tail Wheel 3-Point W/ 15" Lam. Tire
(Applies to RCF3096 only)
Ref.
Part No.
804-016C
804-066C
805-255C
814-058C
814-161C
815-092C
815-230C
815-231C
816-286C
822-091C
822-092C
827-036C
890-961C
Dwg 33828
312-616D
312-811D
327-129H
800-001C
800-080C
802-106C
802-135C
802-162C
802-280C
802-326C
803-026C
803-037C
803-271C
803-289C
803-308C
804-015C
17.
18.
19.
20.
11.
12.
13.
14.
15.
16.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
21.
22.
23.
24.
25.
26.
27.
28.
29.
Part Description
Drawing Image Number
TAILWHEEL ARM ADJUST PLATE
TAILWHEEL BEAM MOUNTING BRKT.
TAILWHEEL BEAM WLDMT SHORT
GREASE ZERK STRAIGHT 1/4-28
GREASE ZERK 1/4-28 THD FORMING
RHSNB 1/2-13X1 1/2 GR5
HUB STUD 1/2-20X1 5/8 GR5
HHCS 5/8-11X3 1/2 GR5
HHCS 3/4-10X7 1/2 GR5
HHCS 1/2-20X1 1/4 GR5
NUT LOCK 3/4-10 PLT
NUT HEX WHIZ 1/2-13 PLT
NUT HEX TOP LOCK 5/8-11 PLT
NUT HEX 1 1/4-7(MACHINED)PLAIN
NUT HEX FLG/LK 1/2-20 PLT GR G
WASHER LOCK SPRING 1/2 PLT
WASHER FLAT 1/2 SAE PLT
WASHER MACH 2.25 X 1.50 X 14GA
PIN ROLL 3/8 X 2 1/2 PLT
TIRE & WHEEL LAMINATED 4.0 X 8
LAM 4X8 TR-WL-HUB-YOKE 25 SER.
HUB & SPINDLE ASSY 4 BOLT
HUB 4 BLT W/CUPS, ZERK & STUDS
HUB 4BLT DUCTILE(USE 815-230C)
OIL SEAL DBL LIP 2.441 BORE
BRG 1.25ID CONE 15123
BRG CUP 2.44OD 15245
BUSHING TW 1.25ODX.78IDX5 1/4
RC25 TAILWHEEL YOKE
Comments
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 31 327-149P
Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire
(Applies to RCF3096 only)
33356
327-149P - 32 07/20/20
Transport Axle 3-Point & Semi-Mount W/ 15" Lam. Tire
(Applies to RCF3096 only)
Ref.
Part No.
17.
18.
19.
20.
11.
12.
13.
14.
15.
16.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
21.
22.
23.
24.
25.
26.
27.
28.
805-255C
806-184C
814-058C
814-161C
815-092C
815-230C
815-231C
816-286C
822-091C
822-092C
827-036C
890-961C
Dwg 33356
326-488H
326-559H
326-968D
800-001C
800-080C
802-135C
802-280C
802-326C
802-360C
803-026C
803-263C
803-289C
803-308C
804-015C
804-016C
804-066C
Part Description
Drawing Image Number
3-PNT TAILWHEEL MOUNT
AXLE 96"
PIVOT SPACER BUSHING
GREASE ZERK STRAIGHT 1/4-28
GREASE ZERK 1/4-28 THD FORMING
HUB STUD 1/2-20X1 5/8 GR5
HHCS 3/4-10X7 1/2 GR5
HHCS 1/2-20X1 1/4 GR5
HHCS 3/4-10X6 1/2 GR5
NUT LOCK 3/4-10 PLT
NUT HEX FLANGE LOCK 5/8-11 PLT
NUT HEX 1 1/4-7(MACHINED)PLAIN
NUT HEX FLG/LK 1/2-20 PLT GR G
WASHER LOCK SPRING 1/2 PLT
WASHER FLAT 1/2 SAE PLT
WASHER MACH 2.25 X 1.50 X 14GA
PIN ROLL 3/8 X 2 1/2 PLT
U-BOLT 5/8-11 X 4 1/32 X 5 1/2
TIRE & WHEEL LAMINATED 4.0 X 8
LAM 4X8 TR-WL-HUB-YOKE 25 SER.
HUB & SPINDLE ASSY 4 BOLT
HUB 4 BLT W/CUPS, ZERK & STUDS
HUB 4BLT DUCTILE(USE 815-230C)
OIL SEAL DBL LIP 2.441 BORE
BRG 1.25ID CONE 15123
BRG CUP 2.44OD 15245
BUSHING TW 1.25ODX.78IDX5 1/4
RC25 TAILWHEEL YOKE
Comments
As Required
As Required
As Required
As Required
As Required
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 33 327-149P
Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire
(Applies to RCF3096 only)
33357
327-149P - 34 07/20/20
Transport Axle 3-Point & Semi-Mount W/ 21" Lam. Tire
(Applies to RCF3096 only)
Ref.
Part No.
803-289C
803-308C
804-015C
804-016C
804-023C
804-074C
805-255C
806-184C
814-059C
815-092C
815-230C
815-231C
816-286C
822-091C
822-092C
827-036C
Dwg 33357
312-067K
312-084L
312-100H
312-231D
326-496H
326-559H
326-968D
800-001C
800-080C
802-135C
802-272C
802-326C
802-360C
803-026C
803-027C
803-263C
17.
18.
19.
20.
11.
12.
13.
14.
15.
16.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
27.
28.
29.
30.
21.
22.
23.
24.
25.
26.
31.
32.
Part Description
Drawing Image Number
RC35 TAILWHEEL ASSY-21
RC 35 TW & YOKE ASSY
RC35 YOKE WLDMT
TAILWHEEL WASHER
SEMI-MOUNT TAILWHEEL ARM
AXLE 96"
PIVOT SPACER BUSHING
GREASE ZERK STRAIGHT 1/4-28
GREASE ZERK 1/4-28 THD FORMING
HUB STUD 1/2-20X1 5/8 GR5
HHCS 3/4-10X10 GR5
HHCS 1/2-20X1 1/4 GR5
HHCS 3/4-10X6 1/2 GR5
NUT LOCK 3/4-10 PLT
NUT HEX 3/4-10 PLT
NUT HEX FLANGE LOCK 5/8-11 PLT
NUT HEX 1 1/4-7(MACHINED)PLAIN
NUT HEX FLG/LK 1/2-20 PLT GR G
WASHER LOCK SPRING 1/2 PLT
WASHER FLAT 1/2 SAE PLT
WASHER LOCK SPRING 3/4 PLT
WASHER MACH 3.25 X 1.75 X 10GA
PIN ROLL 3/8 X 2 1/2 PLT
U-BOLT 5/8-11 X 4 1/32 X 5 1/2
TIRE & WHEEL LAM. 6X9X21(TALL)
HUB & SPINDLE ASSY 4 BOLT
HUB 4 BLT W/CUPS, ZERK & STUDS
HUB 4BLT DUCTILE(USE 815-230C)
OIL SEAL DBL LIP 2.441 BORE
BRG 1.25ID CONE 15123
BRG CUP 2.44OD 15245
BUSHING TW 1.25ODX.78IDX5 1/4
Comments
As Required
As Required
As Required
As Required
As Required
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 35 327-149P
Transport Axle Pull Type
(Applies to RCF3096 only)
33426
327-149P - 36 07/20/20
Transport Axle Pull Type
(Applies to RCF3096 only)
Ref.
Part No.
15.
16.
17.
18.
19.
11.
12.
13.
14.
14.
14.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
Dwg 33426
326-489H
326-559H
326-968D
327-245H
330-938K
331-795L
802-099C
802-360C
803-019C
803-026C
803-263C
806-184C
814-265C
814-444C
814-478C
814-449C
814-450C
814-451C
814-461C
815-401C
815-402C
Part Description
Drawing Image Number
PULL TAILWHEEL
AXLE 96"
PIVOT SPACER BUSHING
PULL TAILWHEEL
HUB 5 BOLT COMPLETE
SPINDLE AND HUB ASSY
HHCS 1/2-13X3 1/4 GR5
HHCS 3/4-10X6 1/2 GR5
NUT LOCK 1/2-13 PLT
NUT LOCK 3/4-10 PLT
NUT HEX FLANGE LOCK 5/8-11 PLT
U-BOLT 5/8-11 X 4 1/32 X 5 1/2
TIRE & WHL LAM. 6X9X21(5-BOLT)
RPBY 814-478C
NEW TIRE FF 25.5X8-14 20PLY
TIRE, AC 29" 16 PLY 5 BOLT
TIRE H29X9.0X15 USED
TUBE FOR 29X9.0-15
RIM 2PC 5BLT 15X6.5
SPINDLE, SINGLE BOLT-ON 7/8-14
SPINDLE, DUAL BOLT-ON 7/8-14
Comments
S/N _______-
S/N _______+
S/N _______-
S/N _______+
Foam Filled
S/N _______-
S/N _______-
Section 3: Hitch & Tailwheel
Revision
07/20/20 - 37 327-149P
Blade Carrier CCW
(Applies to RCF3096 only)
33347
327-149P - 38 07/20/20
Blade Carrier CCW
(Applies to RCF3096 only)
4.
5.
6.
7.
8.
1.
1.
1.
1.
2.
3.
Ref.
Part No.
Dwg 33347
N/A
N/A
N/A
N/A
N/A
312-820H
802-277C
803-170C
804-147C
820-615C
318-586A
Part Description
Drawing Image Number
BLADE SPACER 16 GA
BLADE SPACER 18 GA
BLADE SPACER 20 GA
BLADE SPACER 24 GA
CCW BLADE CARRIER ASSY.
15 DISHPAN WLDMT LG.HUB(COMER)
BLD BLT 1 1/8-12X3.44 W/.25KEY
NUT HEX TOP LOCK 1 1/8-12 PLT.
WASHER FLAT 1 HARD ASTMF436 PN
CUTTER BLADE 1/2X4X20.5 CCW
BLADE BOLT KIT
Comments
Section 4: Blade Drive
Revision
07/20/20 - 39 327-149P
Blade Carrier CW
(Applies to RCF3096 only)
33348
327-149P - 40 07/20/20
Blade Carrier CW
(Applies to RCF3096 only)
4.
5.
6.
7.
8.
1.
1.
1.
1.
2.
3.
Ref.
Part No.
Dwg 33348
N/A
N/A
N/A
N/A
N/A
312-820H
802-277C
803-170C
804-147C
820-614C
318-586A
Part Description
Drawing Image Number
BLADE SPACER 16 GA
BLADE SPACER 18 GA
BLADE SPACER 20 GA.
BLADE SPACER 24GA
CW BLADE CARRIER ASSY.
15 DISHPAN WLDMT LG.HUB(COMER)
BLD BLT 1 1/8-12X3.44 W/.25KEY
NUT HEX TOP LOCK 1 1/8-12 PLT.
WASHER FLAT 1 HARD ASTMF436 PN
CUTTER BLADE 1/2X4X20.5 CW
BLADE BOLT KIT
Comments
Section 4: Blade Drive
Revision
07/20/20 - 41 327-149P
Blade Drive 3-Point & Semi-Mount
(Applies to RCF3096 only)
33349
327-149P - 42 07/20/20
Ref.
Part No.
Dwg 33349
1.
2.
15.
16.
17.
18.
18.
11.
12.
13.
14.
7.
8.
9.
10.
3.
4.
5.
6.
312-765H
326-979D
802-034C
802-065C
802-314C
803-299C
804-015C
804-157C
804-161C
817-259C
826-255C
826-356C
826-490C
826-503C
826-722C
837-101C
826-648C
19.
826-224C
Blade Drive 3-Point & Semi-Mount
(Applies to RCF3096 only)
Part Description Comments
Drawing Image Number
SEE BLADE CARRIER CW FOR COMPONENTS
SEE BLADE CARRIER CCW FOR
COMPONENTS
SHIELD BRACKET WELDMENT
OUTER SHIELD RCF3096
HHCS 1/2-13X1 1/4 GR5
HHCS 3/4-10X2 1/4 GR5
HHCS M8X1.25X20 GR8.8
NUT HEX FLG TOP LK 3/4-10 PLT
WASHER LOCK SPRING 1/2 PLT
WASHER SPRING LOCK M8 PLT
WASHER FLAT M8 PLT
KNOB 3/8-16 FEMALE THD 2 3/8OD
PTO STD.W/4-PLATE SC CAT4 540
T-BOX 1.75-20 1:1.35
COMER U0.210.7100.00 DIPSTICK
COMER VENT 8.6.7.00161
GBOX RC35 1.75-6 1:1.69 CCW
LAND PRIDE CONE
LARGE SHAFT CONE W ACCESS DOOR This cone has been replaced with
837-101C
DRVLN 10F 1.75-20 FLXCPLR
Section 4: Blade Drive
Revision
07/20/20 - 43 327-149P
Blade Drive Pull Type W/ Equal Angle
(Applies to RCF3096 only)
33350
327-149P - 44 07/20/20
Ref.
Part No.
Dwg 33350
1.
2.
27.
28.
29.
29.
23.
24.
25.
26.
18.
18.
19.
20.
21.
22.
15.
16.
17.
18.
13.
13.
13.
14.
15.
15.
9.
10.
11.
12.
7.
8.
8.
9.
3.
4.
5.
6.
803-021C
803-299C
804-015C
804-024C
804-021C
804-022C
804-157C
804-161C
817-259C
822-100C
826-151C
826-256C
826-356C
826-490C
826-503C
826-722C
837-101C
826-648C
312-681S
312-765H
312-999D
326-002D
326-979D
327-571D
312-833D
327-593D
312-715D
800-069C
802-034C
802-065C
802-280C
802-146C
802-260C
802-314C
803-026C
803-019C
30.
826-224C
Blade Drive Pull Type W/ Equal Angle
(Applies to RCF3096 only)
Part Description Comments
Drawing Image Number
SEE BLADE CARRIER CW FOR COMPONENTS
SEE BLADE CARRIER CCW FOR
COMPONENTS
TRUNION ASY
SHIELD BRACKET WELDMENT
CASTING TRUNION MACHINED
TUBE 1 OD X 11/16 LG. X 5/32w
OUTER SHIELD RCF3096
TRUNNION SUPPORT
SUPPORT UPRIGHT TRUNION
TRUNION SPACER
PIPE 1/2 SCH. 40 X 4 15/16
SNAP RING INT 2.835
HHCS 1/2-13X1 1/4 GR5
HHCS 3/4-10X2 1/4 GR5
S/N _______+
S/N _______-
S/N _______+
S/N _______-
S/N _______+
S/N _______-
S/N _______-
RHSNB 5/16-18X1 GR5
HHCS 5/8-11X7 1/2 GR5
HHCS 1/2-13X7 GR5
HHCS M8X1.25X20 GR8.8
NUT LOCK 3/4-10 PLT
NUT LOCK 1/2-13 PLT
NUT HEX 5/8-11 PLT
NUT HEX FLG TOP LK 3/4-10 PLT
WASHER LOCK SPRING 1/2 PLT
WASHER FLAT 3/4 USS PLT
WASHER FLAT 5/8 SAE PLT
WASHER LOCK SPRING 5/8 PLT
WASHER SPRING LOCK M8 PLT
WASHER FLAT M8 PLT
KNOB 3/8-16 FEMALE THD 2 3/8OD
BRG INS 1.37IDX2.83OD LOCK
PTO CAT. 4 X 20.5 FIXED 540
PTO J/S.W/4-PLATE SC CAT4 540
T-BOX 1.75-20 1:1.35
COMER U0.210.7100.00 DIPSTICK
COMER VENT 8.6.7.00161
GBOX RC35 1.75-6 1:1.69 CCW
LAND PRIDE CONE
LARGE SHAFT CONE W ACCESS DOOR
S/N _______+
S/N _______-
S/N _______-
S/N _______+
S/N _______-
S/N _______-
This cone has been replaced with
837-101C
DRVLN 10F 1.75-20 FLXCPLR
Section 4: Blade Drive
Revision
07/20/20 - 45 327-149P
Blade Drive Pull Type W/CV
(Applies to RCF3096 only)
35178
327-149P - 46 07/20/20
Ref.
Part No.
Dwg 35178
1.
2.
15.
16.
17.
18.
19.
20.
11.
12.
13.
14.
7.
8.
9.
10.
3.
4.
5.
6.
25.
26.
27.
27.
21.
22.
23.
24.
312-765H
326-979D
327-229D
800-080C
801-035C
802-034C
802-065C
802-082C
802-091C
802-314C
803-037C
803-299C
804-015C
804-016C
804-157C
804-161C
817-259C
822-094C
826-053C
826-225C
826-356C
826-490C
826-503C
826-722C
837-101C
826-648C
28.
826-224C
Blade Drive Pull Type W/CV
(Applies to RCF3096 only)
Part Description Comments
Drawing Image Number
SEE BLADE CARRIER CW FOR COMPONENTS
SEE BLADE CARRIER CCW FOR
COMPONENTS
SHIELD BRACKET WELDMENT
OUTER SHIELD RCF3096
PILLOW BLOCK BRG SUPPORT 3096
GREASE ZERK 1/4-28 THD FORMING
SCREW SET 5/16-18 SKT KP X 3/8
HHCS 1/2-13X1 1/4 GR5
HHCS 3/4-10X2 1/4 GR5
HHCS 1/2-13X1 3/4 GR5
HHCS 1/2-13X1 1/2 GR5
HHCS M8X1.25X20 GR8.8
NUT HEX WHIZ 1/2-13 PLT
NUT HEX FLG TOP LK 3/4-10 PLT
WASHER LOCK SPRING 1/2 PLT
WASHER FLAT 1/2 SAE PLT
WASHER SPRING LOCK M8 PLT
WASHER FLAT M8 PLT
KNOB 3/8-16 FEMALE THD 2 3/8OD
BRG PB 1.37ID
PTO CV 2400 X 60 540 RPM
PTO W/STUB SHAFT/SC 540 1 3/4
T-BOX 1.75-20 1:1.35
COMER U0.210.7100.00 DIPSTICK
COMER VENT 8.6.7.00161 3/8MNPT
GBOX RC35 1.75-20 1:1.69 STD
LAND PRIDE CONE
LARGE SHAFT CONE W ACCESS DOOR This cone has been replaced with
837-101C
DRVLN 10F 1.75-20 FLXCPLR
Section 4: Blade Drive
Revision
07/20/20 - 47 327-149P
Driveline 540 RPM (826-151C) Eurocardan
(Applies to RCF3096 only)
16610
327-149P - 48 07/20/20
Ref.
Part No.
Dwg 16610
826-151C
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
5.
6.
7.
8.
1.
2.
3.
4.
1786710
1215733
1885704
1215735
1885709
1876030D
1885703
1006020
1706027
6331080
1528040D
818-540C
818-552C
6560508
1016013
1004227
826-578C
Driveline 540 RPM (826-151C) Eurocardan
(Applies to RCF3096 only)
Part Description
Drawing Image Number
PTO CAT. 4 X 20.5 FIXED 540
*
EC TUBE BEARING (OUTER TUBE)
EC STIFFENING RING
EC LONG CONE
EC STOP RING
EC SAFETY SLEEVE
EC OUTER TUBE SHIELD
EC STANDARD CONE
EC CROSS ASSEMBLY
EC OUTER TUBE YOKE
EC 10X80-DIN-1481 O/TUBE R/PIN
EC OUTER TUBE
DECAL DANGER GUARD MISS PTO
DECAL DANGER PTO DRIVELINE
N/A
EC GREASE ZERK 8X1 45 DEG.
EC YOKE ASSEMBLY
EC PULL COLLAR KIT EVOLUTION
SHIELD KIT, 826-151C
Comments
Complete assembly
Section 4: Blade Drive
Revision
07/20/20 - 49 327-149P
Driveline 540 RPM (826-255C) Eurocardan
(Applies to RCF3096 only)
22283
327-149P - 50 07/20/20
Ref.
Part No.
Dwg 22283
826-255C
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
5.
6.
7.
8.
1.
2.
3.
4.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1786711
1215733
1885702
1215735
1885709
1877052
1876052
1885703
1786710
1446016
1006020
1706029
1526062
6331070
1528084
6331080
1706027
1016012
818-540C
818-552C
6560508
1004220
6560006
1016013
1004225
826-569C
Driveline 540 RPM (826-255C) Eurocardan
(Applies to RCF3096 only)
Part Description
Drawing Image Number
PTO STD.W/4-PLATE SC CAT4 540
*
EC TUBE BEARING (INNER TUBE)
EC STIFFENING RING
EC SHORT CONE
EC STOP RING
EC SAFETY SLEEVE
EC INNER TUBE SHEILD
EC OUTER TUBE SHEILD
EC STANDARD CONE
EC TUBE BEARING (OUTER TUBE)
EC CLUTCH FD4/6 1 3/4 20 SPL
EC CROSS ASSEMBLY
EC INNER TUBE YOKE
EC INNER TUBE (1526084) 620MM
EC 10X70 ROLL PIN
EC 840MM OUT. STOCK LENGTH TB.
EC 10X80-DIN-1481 O/TUBE R/PIN
EC OUTER TUBE YOKE
YOKE ASSEMBLY PULL TYPE
DECAL DANGER GUARD MISS PTO
DECAL DANGER PTO DRIVELINE
N/A
EC GREASE ZERK 8X1 45 DEG.
EC TWIST COLLAR KIT (TRT. END)
EC GREASE ZERK M6X1 STRAIGHT
EC YOKE ASSEMBLY
EC PULL COLLAR KIT
SHIELD KIT, 826-255C &826-258C
Comments
Complete assembly
Shown
Section 4: Blade Drive
Revision
07/20/20 - 51 327-149P
Driveline 540 RPM (826-256C) Eurocardan
(Applies to RCF3096 only)
16173
327-149P - 52 07/20/20
Driveline 540 RPM (826-256C) Eurocardan
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 16173
826-256C
15.
16.
16.
17.
9.
10.
11.
12.
13.
14.
18.
19.
20.
21.
5.
6.
7.
8.
1.
2.
3.
4.
1786711
1215733
1885702
1215735
1885709
1877304
N/A
1876304
1885705
1786710
1896314N327
6331070
1526070
1706029
1006020
1446137
1446037
818-552C
818-540C
6560508
6561306
826-570C
Part Description
Drawing Image Number
PTO J/S.W/4-PLATE SC CAT4 540
*
EC TUBE BEARING (INNER TUBE)
EC STIFFENING RING
EC SHORT CONE
EC STOP RING
EC SAFETY SLEEVE
EC INNER TUBE SHIELD
EC OUTER TUBE SHIELD
EC EXTRA SHORT CONE (FOR MX)
EC TUBE BEARING (OUTER TUBE)
EC OUTER TUBE ASSEMBLY
EC 10X70 ROLL PIN
EC INNER TUBE (1526084) 840MM
EC INNER TUBE YOKE
EC CROSS ASSEMBLY
EC TORQUE LIMITER, (FD 4)
RPBY 1446137
DECAL DANGER PTO DRIVELINE
DECAL DANGER GUARD MISS PTO
EC GREASE ZERK 8X1 45 DEG.
EC GREASE ZERK M6X1 EXTRA SHRT
SHIELD KIT, 826-256C
Comments
Complete assembly
Section 4: Blade Drive
Revision
07/20/20 - 53 327-149P
Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid
(Applies to RCF3096 only)
30279
327-149P - 54 07/20/20
Ref.
Part No.
Dwg 30279
826-053C
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
5.
6.
7.
8.
1.
2.
3.
4.
25.
26.
27.
28.
19.
20.
21.
22.
23.
24.
320684
020469
010490
695580
020672
365722
342221
019519
020616
382647
095758
134713
818-540C
377341
365305
087276
382437
383333
383128
172758
312410
355155
386083
380371
381908
826-590C
359471
Section 4: Blade Drive
Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid
(Applies to RCF3096 only)
Part Description
Drawing Image Number
PTO CV 2400 X 60 540 RPM
*
WS YOKE 1 3/8-21 SPL
WS BOLT M12 X 75
WALTERSCHEID SELF-LCKG HEX NUT
WS YOKE 1 3/8-6 ASGE
WS GREASE ZERK
WS DOUBLE YOKE
WS CROSS & BEARING KIT
WS INBOARD YOKE
WS SPRING PIN 10 X 75
WS PROFILE & SLEEVE
WS INNER PROFILE 16 GA
WS INBOARD YOKE 1B
DECAL DANGER GUARD MISS PTO
WS SHIELD CONE 11 RIB
WALTERSCHEID SCREW
WS BEARING RING - SC25
N/A
WS INNER SHIELD TUBE ROUND
WALTERSCHEID DANGER DECAL-SHLD
WS OUTER SHIELD TUBE OVL.
WS SHIELD CONE 3 RIB
WS CROSS BEARING KIT
WS SUPPORT BEARING
WS CV CONE & BEARING ASSY
WS ZERK
WS QUICK DISCONNECT KIT
SHIELD KIT, 826-053C
WS REINFORCING COLLAR
Comments
Complete assembly
Revision
07/20/20 - 55 327-149P
Driveline Flex Coupler (826-224C) Eurocardan
(Applies to RCF3096 only)
16886
327-149P - 56 07/20/20
Driveline Flex Coupler (826-224C) Eurocardan
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 16886
826-224C
5.
6.
7.
8.
1.
2.
3.
4.
9.
10.
1705278
1785273
1005220
6560208
312-608A
Part Description
Drawing Image Number
FLEX COUPLER 1 3/4-20 (9.21)
*
EC BOLT
EC SPIDER 1 3/4-20 W/TAP HOLE
EC WSH. BD. 35mm O.D/16.5mm I.D
EC BOLT BUSHING
EC RUBBER DISC
EC WASHER 29.8mm O.D/17.2mm I.D
EC NUT
EC SPIDER TUBE
EC GREASE ZERK M8 STRAIGHT
FLEX COUPLER KIT
Comments
Complete assembly
Only sold in kit #10
1 3/4-20
Only sold in kit #10
Only sold in kit #10
Can be ordered seperately & in kit #10
Only sold in kit #10
Only sold in kit #10
S/N 639636-
Includes items 1, 3, 4, 5, 6 & 7
Section 4: Blade Drive
Revision
07/20/20 - 57 327-149P
Driveline Slip Clutch (1446016) Eurocardan
(Applies to RCF3096 only)
15521
327-149P - 58 07/20/20
Driveline Slip Clutch (1446016) Eurocardan
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 15521
1446016
5.
6.
7.
8.
1.
2.
3.
4.
9.
10.
11.
1215012
1706033
1705009
1808010
1708034
1138008
1708016
6821484
1138007
6691010
330-297A
Part Description
Drawing Image Number
EC CLUTCH FD4/6 1 3/4 20 SPL
*
RPBY 330-297A
EC CLUTCH YOKE W/FLANGE
EC CLUTCH BUSHING
EC CLUTCH LINING RING
EC CLUTCH MIDDLE DISK
EC INNER DISK
EC HUB WITH FLANGE
EC CONICAL DOG KIT REPLACEMENT
EC PRESSURE DISK
EC BOLT & SCREW NUT KIT REPL.
SV KIT, EC SLIP CLUTCH SPRING
Comments
Complete assembly
1 3/4-20
Contains 8 Springs
Section 4: Blade Drive
Revision
07/20/20 - 59 327-149P
Driveline Slip Clutch (1446137) Eurocardan
(Applies to RCF3096 only)
30198
327-149P - 60 07/20/20
Driveline Slip Clutch (1446137) Eurocardan
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 30198
1446137
5.
6.
7.
8.
1.
2.
3.
4.
9.
10.
11.
12.
1706033
1706313
803-279C
6001010
6691010
330-297A
1138007
1138008
1808010
1708034
1705009
6761480
Part Description
Drawing Image Number
EC TORQUE LIMITER, (FD 4)
*
EC CLUTCH YOKE W/FLANGE
EC HUB WITH FLANGE
NUT HEX M10X1.5 PLT
EC BOLT (M10X100)
EC BOLT & SCREW NUT KIT REPL.
SV KIT, EC SLIP CLUTCH SPRING
EC PRESSURE DISK
EC INNER DISK
EC CLUTCH LINING RING
EC CLUTCH MIDDLE DISK
EC CLUTCH BUSHING
EC BOLT, NUT & WASHER KIT
Comments
Complete assembly
Section 4: Blade Drive
Revision
07/20/20 - 61 327-149P
Driveline Stub Shaft Pull Type 540 RPM (826-225C) Eurocardan
(Applies to RCF3096 only)
15995
327-149P - 62 07/20/20
Section 4: Blade Drive
Driveline Stub Shaft Pull Type 540 RPM (826-225C) Eurocardan
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 15995
826-225C
13.
14.
15.
16.
9.
9.
10.
11.
12.
13.
5.
6.
7.
8.
1.
2.
3.
4.
1786710
1215733
1885702
1215735
1885709
1876023D
1885705
1896028S821
1896028D821
6331080
1706027
1006020
1446137
1446037
818-552C
818-540C
6560508
Part Description
Drawing Image Number
PTO W/STUB SHAFT/SC 540 1 3/4
*
EC TUBE BEARING (OUTER TUBE)
EC STIFFENING RING
EC SHORT CONE
EC STOP RING
EC SAFETY SLEEVE
N/A
EC OUTER TUBE SHEILD
EC EXTRA SHORT CONE (FOR MX)
EC OUTER TUBE ASSY (HRDND)
EC OUTER TUBE ASSY
EC 10X80-DIN-1481 O/TUBE R/PIN
EC OUTER TUBE YOKE
EC CROSS ASSEMBLY
EC TORQUE LIMITER, (FD 4)
RPBY 1446137
DECAL DANGER PTO DRIVELINE
DECAL DANGER GUARD MISS PTO
EC GREASE ZERK 8X1 45 DEG.
Comments
Complete assembly
Revision
Rev. 2
Rev. 1
07/20/20 - 63 327-149P
Gearbox (826-722C) Comer
(Applies to RCF3096 only)
33921
327-149P - 64 07/20/20
Gearbox (826-722C) Comer
(Applies to RCF3096 only)
Ref.
Part No.
Part Description
Dwg 33921
826-722C
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
5.
6.
7.
8.
1.
2.
3.
4.
25.
26.
27.
28.
19.
20.
21.
22.
23.
24.
0.210.2001.00
8.7.1.02348
8.5.2.00332
A.709.500
8.0.9.00143
8.1.1.00501
0.210.6002.00
8.5.1.00533
8.6.5.00006
0.210.1300.00
0.252.7525.00
0.121.7101.00
8.6.6.00201
8.4.7.02265
0.132.7106.00
0.210.5002.00
A.712.500
04-011
0.210.0300.00
8.7.1.01107
0.139.7100.00
0.210.3001.00
0.139.7101.00
8.2.2.00555
0.102.7510.00
0.276.7101.0
8.4.7.00146
826-490C
Drawing Image Number
GBOX RC35 1.75-20 1:1.69 STD
*
CO INPUT SHAFT 1.75-20
CO DUST LIP (45X85X10)
CO SNAP RING UNI 7437
COMER SHIM KIT
CO BRG 30209 TAPPERED
CO BOLT M10X22 HHB
CO GEAR CROWN Z27 M5.3
CO SNAP RING 50 UNI7435
CO OIL PLUG 3/8
CO COVER
CO SHIM 45.3X2.5
CO CAP
CO PLUG 3/8 GAS (SOLID PLUG)
CO COTTER PIN B 5X60
CO NUT M30 X 1.5
CO PINION Z16 M5.3
COMER SHIM KIT
ITG BRG ASSEMBLY
CO CASTING & MACHINE
CO SEAL (50x90x10)
CO SEAL RETAINER
CO OUTPUT SHAFT
CO BLANK WASHER
CO NUT, CASTLE M30 X 2
CO SHIM 44X30.3X1
CO SPACER (30.1X44.5X3.6)
CO COTTER PIN B6 X 60
COMER U0.210.7100.00 DIPSTICK
Comments
Complete assembly
Section 4: Blade Drive
Revision
07/20/20 - 65 327-149P
Gearbox, T-Box 540 RPM (826-356C) Comer
(Applies to RCF3096 only)
22346
327-149P - 66 07/20/20
Gearbox, T-Box 540 RPM (826-356C) Comer
(Applies to RCF3096 only)
Ref.
Part No.
Part Description
Dwg 22346
826-356C
15.
16.
17.
18.
9.
10.
11.
12.
13.
14.
19.
20.
5.
6.
7.
8.
1.
2.
3.
4.
0.279.0305.00
0.278.7104.00
8.1.1.00501
0.279.3016.00
0.252.7525.00
0.124.7135.00
0.279.6001.00
0.279.5001.00
0.252.7510.00
8.4.1.00978
8.7.1.02686
0.279.1315.00
8.0.9.00107
0.279.2013.00
0.279.1313.00
8.0.9.00125
8.7.3.02685
A252.500
8.6.6.00201
8.6.7.00161
Drawing Image Number
T-BOX 1.75-20 1:1.35
*
CO CASING
CO NUT LOCK M45 X 1.5
CO BOLT M10X22 HHB
CO THROUGH SHAFT 1 3/4" Z20
CO SHIM 45.3X2.5
CO LABEL
CO GEAR CROWN Z27 M5.7
CO GEAR PINION Z20 M5.7
CO SHIM (45.3X65.3X1)
CO PARALLEL KEY B 14 X 9 X 40
CO DUST LIP 45 X 72 X 8
CO COVER
CO RL BRG 30309 (45X100X27.25)
CO INPUT SHAFT 1 3/4" Z20
CO EXTENSION
CO BEARING 32209
CO OIL SEAL 52 X 85 X 10
CO SHIM 65.3MM RTA25
CO PLUG 3/8 GAS
CO OIL FILLER PLUG 3/8
*
Notes: Oil Type 80-90W Capacity 4.5 Pints
Comments
Complete assembly
Section 4: Blade Drive
Revision
07/20/20 - 67 327-149P
Guard Chain Dual Front
(Applies to RCF3096 only)
33342
327-149P - 68 07/20/20
Guard Chain Dual Front
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 33342
326-583A
5.
6.
7.
8.
1.
2.
3.
4.
326-580K
326-581K
326-949D
326-950D
326-954D
802-183C
803-037C
891-212C
Part Description
Drawing Image Number
FRONT DOUBLE CHAIN GUARD 3096
*
FRONT DBL CHAIN GUARD RH 3096
FRONT DBL CHAIN GUARD LH 3096
FRONT CHAIN GUARD RH
FRONT CHAIN GUARD LH
ROUND ROD 1/4 X 53
RHSNB 1/2-13X1 GR5
NUT HEX WHIZ 1/2-13 PLT
CHAIN WELD 5/16 PRF X 9-LINK
Comments
Complete assembly
Revision
Section 5: Guards
07/20/20 - 69 327-149P
Guard Chain Dual Rear
(Applies to RCF3096 only)
33413
327-149P - 70 07/20/20
Guard Chain Dual Rear
(Applies to RCF3096 only)
1.
2.
3.
4.
5.
6.
Ref.
Part No.
Dwg 33413
318-478D
326-536A
326-948D
802-183C
803-037C
890-393C
Part Description
Drawing Image Number
ROUND ROD .25 X 59
REAR DOUBLE CHAIN GUARD 96"
REAR CHAIN GUARD BRACKET
RHSNB 1/2-13X1 GR5
NUT HEX WHIZ 1/2-13 PLT
CHAIN WELD 5/16 PROOF X 7-LINK
Comments Revision
Section 5: Guards
07/20/20 - 71 327-149P
Guard Chain Single Front
(Applies to RCF3096 only)
33340
327-149P - 72 07/20/20
Guard Chain Single Front
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 33340
326-582A
5.
6.
7.
8.
1.
2.
3.
4.
326-578K
326-579K
326-949D
326-950D
326-954D
802-183C
803-037C
890-341C
Part Description
Drawing Image Number
FRONT SINGLE CHAIN GUARD 3096
*
FRONT SNGL CHAIN GUARD LH 3096
FRONT SNGL CHAIN GUARD RH 3096
FRONT CHAIN GUARD RH
FRONT CHAIN GUARD LH
ROUND ROD 1/4 X 53
RHSNB 1/2-13X1 GR5
NUT HEX WHIZ 1/2-13 PLT
CHAIN WELD 5/16 PROOF X 5 LINK
Comments
Complete assembly
Revision
Section 5: Guards
07/20/20 - 73 327-149P
Guard Chain Single Rear
(Applies to RCF3096 only)
33364
327-149P - 74 07/20/20
Guard Chain Single Rear
(Applies to RCF3096 only)
1.
2.
3.
4.
5.
6.
Ref.
Part No.
Dwg 33364
318-478D
326-535A
326-948D
802-183C
803-037C
890-400C
Part Description
Drawing Image Number
ROUND ROD .25 X 59
REAR SINGLE CHAIN GUARD 96"
REAR CHAIN GUARD BRACKET
RHSNB 1/2-13X1 GR5
NUT HEX WHIZ 1/2-13 PLT
CHAIN WELD 5/16 PROOF X 4 LINK
Comments Revision
Section 5: Guards
07/20/20 - 75 327-149P
Guard Rubber Front
(Applies to RCF3096 only)
33341
327-149P - 76 07/20/20
Guard Rubber Front
(Applies to RCF3096 only)
Ref.
Part No.
Dwg 33341
326-573A
5.
6.
7.
8.
1.
2.
3.
4.
326-574K
326-952D
326-974D
802-015C
802-183C
803-037C
803-198C
816-717C
Part Description
Drawing Image Number
FRONT RUBBER GUARD 3096
*
FRONT RUBBER GUARD
DEFLECTOR SUPPORT FLAT
FRONT DEFLECTOR BRACKET
RHSNB 3/8-16X1 GR5
RHSNB 1/2-13X1 GR5
NUT HEX WHIZ 1/2-13 PLT
NUT HEX WHIZ 3/8-16 PLT
RUBBER DEFLECTOR 3096
Comments
Complete assembly
Revision
Section 5: Guards
07/20/20 - 77 327-149P
Guard Rubber Rear
(Applies to RCF3096 only)
35000
327-149P - 78 07/20/20
Guard Rubber Rear
(Applies to RCF3096 only)
1.
2.
3.
4.
5.
6.
Ref.
Part No.
Dwg 35000
326-953D
327-130A
327-211D
802-106C
803-037C
816-715C
Part Description
Drawing Image Number
DEFLECTOR SUPPORT FLAT
REAR RUBBER GUARD 3096
REAR FOOT GUARD RH/LH
RHSNB 1/2-13X1 1/2 GR5
NUT HEX WHIZ 1/2-13 PLT
RUBBER DEFLECTOR
Comments Revision
Section 5: Guards
07/20/20 - 79 327-149P
Decal Placement 3-point
(Applies to RCF3096 only)
39800
327-149P - 80 07/20/20
Decal Placement 3-point
(Applies to RCF3096 only)
Ref.
Part No.
16.
17.
18.
19.
11.
12.
13.
13.
14.
15.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
Dwg 39800
818-042C
818-130C
818-142C
NA
818-225C
818-349C
818-402C
818-543C
818-552C
818-556C
818-564C
818-681C
818-830C
844-190C
838-062C
838-094C
838-614C
838-615C
858-718C
858-767C
Part Description
Drawing Image Number
DECAL PATENT PENDING
DECAL CAUTION 540 RPM
DECAL DANGER PTO DRIVELINE EN
DECAL RC120 BLADE ROTATION
DECAL GREASE 10 HRS LH
DECAL GREASE 10 HRS RH
DECAL DANGER PD GUARD MISS SML
DECAL DANGER PTO DRIVELINE
DECAL DANGER THROWN OBJ CUTTER
DECAL DANGER ROTATING BLADES
DECAL NOTICE - 20 MPH MAX
DECAL SAFETY COMBO SUNWEST
DECAL SINGLE DECK SAFETY COMBO
DECAL AMBER NARROW REFLECTOR
DECAL WARNING HYD PRESS LONG
DECAL REFLECTOR RED 2X9
DECAL REFLECTOR AMBER 2X9
DECAL RCF3096 GREAT PLAINS
DECAL GREAT PLAINS 25" CTR LOGO
Comments
S/N D001212N-
S/N D001213N+
Revision
Section 6: Labels
07/20/20 - 81 327-149P
Decal Placement Pull Type
(Applies to RCF3096 only)
39801
327-149P - 82 07/20/20
Decal Placement Pull Type
(Applies to RCF3096 only)
Ref.
Part No.
11.
12.
13.
14.
15.
16.
17.
18.
19.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
Dwg 39801
818-042C
818-130C
818-142C
818-190C
818-225C
818-349C
818-402C
818-543C
818-552C
818-556C
818-564C
818-681C
818-830C
838-062C
838-094C
838-614C
838-615C
858-718C
858-767C
Part Description
Drawing Image Number
DECAL PATENT PENDING
DECAL CAUTION 540 RPM
DECAL DANGER PTO DRIVELINE EN
DECAL FLAG
DECAL RC120 BLADE ROTATION
DECAL GREASE 10 HRS LH
DECAL GREASE 10 HRS RH
DECAL DANGER PD GUARD MISS SML
DECAL DANGER PTO DRIVELINE
DECAL DANGER THROWN OBJ CUTTER
DECAL DANGER ROTATING BLADES
DECAL NOTICE - 20 MPH MAX
DECAL SAFETY COMBO SUNWEST
DECAL AMBER NARROW REFLECTOR
DECAL WARNING HYD PRESS LONG
DECAL REFLECTOR RED 2X9
DECAL REFLECTOR AMBER 2X9
DECAL RCF3096 GREAT PLAINS
DECAL GREAT PLAINS 25" CTR LOGO
Comments Revision
Section 6: Labels
07/20/20 - 83 327-149P
Part Number Index
The Part Number Index is a numeric index of all part numbers included in this manual. The index shows what page(s) the part is used on.
Part Number Page Part Number Page Part Number Page Part Number Page
0.102.7510.00 ...........
0.121.7101.00 ...........
0.124.7135.00 ...........
0.132.7106.00 ...........
0.139.7100.00 ...........
0.139.7101.00 ...........
0.210.0300.00 ...........
0.210.1300.00 ...........
0.210.2001.00 ...........
0.210.3001.00 ...........
0.210.5002.00 ...........
0.210.6002.00 ...........
0.252.7510.00 ...........
0.252.7525.00 ...........
0.276.7101.0 .............
0.278.7104.00 ...........
0.279.0305.00 ...........
0.279.1313.00 ...........
0.279.1315.00 ...........
0.279.2013.00 ...........
0.279.3016.00 ...........
0.279.5001.00 ...........
0.279.6001.00 ...........
010490 ......................
019519 ......................
020469 ......................
020616 ......................
020672 ......................
04-011 .......................
087276 ......................
095758 ......................
1004220 ....................
1004225 ....................
1004227 ....................
1005220 ....................
1006020 ....................
1016012 ....................
1016013 ....................
1138007 ....................
1138008 ....................
1215012 ....................
1215733 ....................
1215735 ....................
134713 ......................
1446016 ....................
1446037 ....................
1446137 ....................
1526062 ....................
1526070 ....................
1528040D ..................
1528084 ....................
1705009 ....................
1705278 ....................
1706027 ....................
1706029 ....................
1706033 ....................
1706313 ....................
1708016 ....................
1708034 ....................
172758 ......................
1785273 ....................
1786710 ....................
1786711 ....................
1808010 ....................
1876023D ..................
1876030D ..................
1876052 ....................
1876304 ....................
1877052 ....................
1877304 ....................
6560508 ....................
6561306 ....................
6691010 ....................
6761480 ....................
6821484 ....................
695580 ......................
8.0.9.00107 ...............
8.0.9.00125 ...............
8.0.9.00143 ...............
8.1.1.00501 ...............
8.2.2.00555 ...............
8.4.1.00978 ...............
8.4.7.00146 ...............
8.4.7.02265 ...............
8.5.1.00533 ...............
8.5.2.00332 ...............
8.6.5.00006 ...............
8.6.6.00201 ...............
8.6.7.00161 ...............
8.7.1.01107 ...............
8.7.1.02348 ...............
8.7.1.02686 ...............
8.7.3.02685 ...............
800-001C ...................
800-069C ...................
800-080C ...................
800-306C ...................
801-035C ...................
802-010C ...................
802-015C ...................
802-017C ...................
802-034C ...................
802-057C ...................
802-064C ...................
802-065C ...................
802-070C ...................
802-074C ...................
802-082C ...................
802-091C ...................
802-096C ...................
802-098C ...................
802-099C ...................
802-106C ...................
802-135C ...................
802-138C ...................
802-146C ...................
802-162C ...................
802-169C ...................
802-183C ...................
802-184C ...................
802-205C ...................
802-224C ...................
802-254C ...................
802-260C ...................
802-269C ...................
802-272C ...................
802-277C ...................
802-280C ...................
802-314C ...................
802-326C ...................
802-360C ...................
802-365C ...................
802-603C ...................
802-762C ...................
802-779C ...................
802-908C ...................
803-013C ...................
803-019C ...................
803-020C ...................
327-149P - 84 07/20/20
Part Number Index
(continued)
Part Number Page Part Number Page Part Number Page
811-133C ...................
811-394C ...................
811-633C ...................
811-676C ...................
812-388C ...................
814-058C ...................
814-059C ...................
814-161C ...................
814-265C ...................
814-444C ...................
814-449C ...................
814-450C ...................
814-451C ...................
814-461C ...................
814-478C ...................
815-092C ...................
815-230C ...................
815-231C ...................
815-242C ...................
815-243C ...................
815-401C ...................
815-402C ...................
815-491C ...................
816-286C ...................
816-497C ...................
816-504C ...................
816-715C ...................
816-717C ...................
817-259C ...................
818-042C ...................
818-130C ...................
818-142C ...................
818-190C ...................
818-225C ...................
818-349C ...................
818-402C ...................
818-540C ...................
818-543C ...................
818-552C ...................
818-556C ...................
818-564C ...................
818-681C ...................
818-830C ...................
820-614C ...................
820-615C ...................
822-020C ...................
822-021C ...................
822-033C ...................
822-034C ...................
822-091C ...................
822-092C ...................
822-094C ...................
822-100C ...................
826-053C ...................
826-151C ...................
826-224C ...................
826-225C ...................
826-255C ...................
826-256C ...................
826-356C ...................
826-490C ...................
826-503C ...................
826-569C ...................
826-570C ...................
826-578C ...................
826-590C ...................
826-648C ...................
826-722C ...................
827-036C ...................
837-062C ...................
837-063C ...................
837-101C ...................
838-062C ...................
838-094C ...................
838-614C ...................
838-615C ...................
840-273C ...................
841-284C ...................
844-190C ...................
850-357C ...................
850-449C ...................
858-718C ...................
858-767C ...................
890-118C ...................
890-341C ...................
890-393C ...................
890-400C ...................
890-637C ...................
890-961C ...................
891-212C ...................
891-246C ...................
A.709.500 ..................
A.712.500 ..................
A252.500 ...................
Dwg ...........................
Dwg 15521 ................
Dwg 15995 ................
Dwg 16173 ................
Dwg 16610 ................
Dwg 16886 ................
Dwg 22283 ................
Dwg 22346 ................
Dwg 30198 ................
Dwg 30279 ................
Dwg 33340 ................
Dwg 33341 ................
Dwg 33342 ................
Dwg 33344 ................
Dwg 33345 ................
Dwg 33347 ................
Dwg 33348 ................
Dwg 33349 ................
Dwg 33350 ................
Dwg 33356 ................
Dwg 33357 ................
Dwg 33364 ................
Dwg 33411 ................
Dwg 33413 ................
Dwg 33426 ................
Dwg 33453 ................
Dwg 33828 ................
Dwg 33921 ................
Dwg 35000 ................
Dwg 35175 ................
Dwg 35178 ................
Dwg 37676 ................
Dwg 39800 ................
Dwg 39801 ................
Dwg 70102 ................
Dwg 70103 ................
Dwg 70104 ................
Dwg 72662 ................
HT250 ........................
N/A ............................
NA .............................
07/20/20 - 85 327-149P
Great Plains Mfg., Inc.
1525 E. North Street
Salina, Kansas 67401 USA www.greatplainsmfg.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement