Bedienungsanleitung

User guide

Guide utilisateur

CV1000

IR / RF Fernbedienung

IR / RF remote control

Télécommande IR / RF

Vielen Dank.

Sie haben ein Gerät mit hohem technischen Standard erworben. Mit dem CV 1000 können bis zu 8 A/V Geräte betrieben werden: TV, VCR, CD, SAT, CBL, DVD, AUDIO und AUX.

Bitte lesen Sie die Installations- und Bedienungsanleitung vor Inbetriebnahme genauestens durch.

Bitte lesen Sie die Bedienungsanleitung auch dann, wenn die Inbetriebnahme bereits von dritter Stelle erfolgt ist.

Sollten wider Erwarten Probleme mit dem System auftreten, informieren Sie bitte umgehend Ihren Fachhändler, bei dem Sie diese Anlage erworben haben.

Bitte heben Sie diese Anleitung zum Nachschlagen auf.

Thank you very much

You have acquired an electronic system with a very high technical standard. With the CV

1000, you can control up to 8 A/V appliances: TV, VCR, CD, SAT, CBL, DVD, AUDIO and

AUX.

Please take care to read the installation and operating instructions before starting.

Please read this manual even if a third party has already installed the system because it contains important information and basic principles of operation.

We would not expect any problems to arise with the system but if any should occur please inform the dealer from whom you bought this device.

Please keep these instructions ready to hand whenever you may need to consult them.

Merci de votre confiance.

Vous avez acheté un appareil électronique de haute technologie. Grâce à la CV

1000 vous pouvez contrôler jusqu’à 8 appareils A/V : TV, VCR, CD, SAT, CBL,

DVD, AUDIO et AUX.

Veuillez tout d’abord lire les instructions d’installation et de fonctionnement de ce guide.

Veuillez lire le guide utilisateur même si une tierce personne a déjà installé la télécommande car il contient des informations importantes et les principes de base de l’utilisation.

En cas de dysfonctionnement, veuillez contacter votre revendeur.

Nous vous conseillons de garder ce guide à portée de main.

DEUTCH ................................................................

35

FRANÇAIS ................................................................

- 2 -

1

3

5

7

9

11

- 3 -

8

10

2

4

6

Contents

1. General Safety Note..........................................................36

2. Introduction .......................................................................38

3. Installing the batteries .......................................................39

4. Description of the CV1000 “rubber” keys .........................40

5. Description of the CV1000 “LCD” keys ............................41

6. Programming using 3 Digit Code Tables for the TV,

VCR, CD, SAT, CBL, DVD, AUDIO and AUX ..................45

7. Programming using Brand search method........................47

8. Programming using Code search method.........................49

9. Identifying codes found using the search procedures ......52

10. Programming a Macro.......................................................53

11. Channel toggle key ...........................................................56

12. Setting key labels .............................................................59

13. Code learning....................................................................61

14. Extra functions ..................................................................65

15. Problems and troubleshooting ...........................................68

- 36 -

1) General Safety Note

Technical manipulation of the product or any changes to the product are forbidden, due to security and approval issues.

Do not use sharp or metal objects on the LCD screen.

Do not press hard on the glass LCD screen.

Take care of proper starting up the device - consult your user guide.

Children should use the device only under adult supervision.

Avoid the following :

· strong mechanical tear and wear

· high temperature

· strong vibrations

· high humidity

Please also respect the additional safety notes in the various user guide chapters. For questions not covered from the user guide please contact our technical hotline or another specialist.

To insure a proper set up please read the manual and safety notes carefully.

- 37 -

Battery change :

The device may only be used with 4 AAA batteries - never try to connect to another power supply. When inserting batteries be sure the right polarity is used. Remove the batteries when the device is not used for a longer period. Make sure that the batteries are not short circuited and are not disposed in fire (danger of explosion)

Batteries do not belong in children hands. Do not leave batteries lying around openly - they might be swallowed by children or animals. If this happens see a doctor immediately.

Leaking or damaged batteries can upon contact with skin cause burning or acid damage - if necessary use suitable gloves

Disposal of batteries :

Batteries are special waste and do not belong in general household waste disposal.

By law, the end-user is required to dispose of used batteries by returning them - disposal through household waste is forbidden. Your used batteries can be returned to any of our shops or to our headquarters, as well as to all local authorized collection points.

Keep the environment safe.

- 38 -

2) Introduction

The CV 1000 is designed to control up to 8 devices (TV, VCR, CD, SAT,

CBL, DVD, AUDIO, AUX). The AUX key can be used to control any other audio/video appliance.

To allow direct control of all these appliances, in a convenient way, the CV

1000 includes a LCD screen. The LCD can display only the functions you need during a certain sequence e.g.: during the setting of CV 1000 to control an A/V appliance or when you are controlling one of your appliances.

The CV 1000 has unique features, combined to a big storage capacity, such as :

“Macro” option, in order to save a sequence: a total number of 20 key strokes can be stored under each of the 9 available Macro keys

code learning, up to 40 keys per each mode

channel scan/search function

video plus / show-view key

All power off feature : to switch off all the modes in 2 presses

TV Volume/ Mute, whatever the last mode was selected

Channel toggle key

Customising of the screen, using a predefined list of symbol, according to your specific needs

RF transmission to control your appliances through walls and ceilings

(RF extender PowerMid requested, sold separately).

The CV 1000 contains a library of codes that are pre-programmed into the remote control. This library covers nearly all the audio video products on the market today.

To make it easy for you to find the right code for your audio video appliance, we advise to use the CODE SEARCH feature.

- 39 -

3) Installing the batteries

1. Open the cover on the back of the CV 1000

2. Insert 4 batteries (LR03 alkaline). Make sure the batteries are the same brand and are NEW and observe polarities indicated inside the battery compartment.

3. All the user programmed parameters will be retained indefinitely during battery replacement

- 40 -

4) Description of the CV1000 “rubber” keys

1 : LED : Turns on whenever a rubber key or an LCD key is pressed and indicates when commands are being transmitted.

2 : TV, VCR, CD, SAT, CBL, DVD, AUDIO, AUX mode : To select the appliance you wish to control.

3 : POWER : to switch off the last selected mode

4 : VOL + / - : to control the volume

5 : MACRO : to launch a macro (see chapter 10)

6 : SET UP : to set the remote control for the appliance you wish to control. Allow the access to secondary functions:

- Press and release the Setup key (the S segment appears on the top right hand corner of the LCD screen)

- Press the desired secondary function key (the "S" is turned off).

7: MUTE to turn on and off the sound

8: CHAN +/ : to select the next or the previous channel

9: TELETEXT ON : to display Teletext

10: TELETEXT OFF : to turn off Teletext

11: PLAY, REW, FF, REC, STOP, PAUSE : correspond to the commands of your original remote control (VCR, DVD and CD modes) and fast text colour keys in TV, CBL and SAT modes.

Error Indication

The LED flashes 3 times and the sounder beeps 3 times for any error condition.

- 41 -

5) Description of the CV1000 “LCD” keys

The LCD Display

The Liquid Crystal Display (LCD) acts as a “Virtual Keypad” comprising a

15 position segmented “key” area. Pressing the “SCREEN” key lets you toggle between two available sets, or “screens” of keys for the mode you are in.

The display is normally blank when the remote is not in use. Pressing the

Setup key, any Mode key, the Macro key or any LCD touch key turns the display panel on. The remaining rubber keys do not activate the display.

- 42 -

All the appliance can be controlled through 2 LCD screens. Common screen keys are described below.

Typical Screen1

TV

4

7

AV

2

5

8

0

3

6

9

Numeric keys 0 - 9 : For digit or numeric key entries e.g. to select the channel number, or to enter the code of your device

-/- : In connection with the numeric keys this key allows you to directly select channels higher than 9 (depending on the appliance).

A/V : Selection of the SCART plug to view or record e.g. DVD, SAT, VCR, …

SEARCH : To scan up available program channels or tracks (see chapter 14.4)

SEARCH P<P

SCREEN

P<P: Allows to program 2 specific channels and switch between them with a single key press

(see chapter 11)

SCREEN : To toggle access between first and second mode screens

Typical Screen2

UP, DOWN, LEFT, RIGHT : Navigation keys used

MENU i

OK

SLEEP

EXIT

SCREEN in Menu.

MENU : To display the menu.

OK : Confirms menu selections.

EXIT: To turn Menu OFF i : Info key: to display the program channel and title information, etc.

- 43 -

Other Useful LCD Keys:

: Teletext Mix : (TV, CBL & SAT) Allows to mix the Teletext and the picture of the selected channel

: (TV, CBL & SAT) Stops page change in teletext mode.

SV/V+ : (VCR) corresponds to “Showview” or “Videoplus” functions (see chapter 14.5).

: (VCR) for tape speed i.e. short-play or long play.

10 : (DVD) is for track digit entries greater than 0-9 (e.g. +10).

REPEAT : (DVD) to repeat the disc playback either completely or from two User-set points (Repeat A-B).

T-C : (DVD) Disc Track or Chapter playback

FAV : (SAT & CBL) is for the devices “Favourite” channel function

GUIDE : (SAT & CBL) to call up the devices on-screen program guide

A-B : (AUDIO) Speaker A or B

DSP : (AUDIO) Digital Signal Processing selection

EFFECT : (AUDIO) DSP Effects toggle

MODE : (AUDIO) AM or FM Tuner selection

- 44 -

SLEEP : (TV Only) To turn off your TV after a period of 1 to 99 minutes.

Proceed as follows :

1. The remote must be in TV Mode with the “second” display screen being shown.

2. Press and hold the LCD “SLEEP” Key until the LED remains on

(occurring after approximately 2-3 seconds) and display will show the

Sleep Setup Screen.

3. Release the “SLEEP” key.

4. Press and release the numeric keys (01-99) for the time required. The

LED will blink off to indicate keypress acceptance and the remote display will return to normal operation.

5. TV Sleep Timer now set. Leave the Remote pointing towards the TV with an unobstructed path.

To cancel the Sleep Timer, press and release the Power key in TV Mode or press and hold the SLEEP key until the remote beeps twice.

Programming the CV1000

You program the CV1000 using the Setup key and following the procedures below. Each keypress is acknowledged with an LED blink and a beep from the sounder. 3 LED blinks and sounder beeps indicate an incorrect or invalid entry.

- 45 -

6) Programming using 3 Digit Code Tables for the TV,

VCR, CD, SAT, CBL, DVD, AUDIO and AUX

Note : you can dedicate any appliance (TV, DVD, SAT...) to the VCR,

DVD, SAT, CD, AUDIO, CBL and AUX keys : you need first to enter the 3 digit code of the appliance you wish to control (found in the code book). In any case, follow the method below :

Setup Screen - Main

SETUP SLEEP

1. Make sure your appliance is switched on (for example TV)

2. Press and hold the Setup key until the LED

MACRO

LEARN

EXIT remains on (occurring after approximately 2-

3 seconds) and display shows the Main

Setup Screen.

3. Release Setup key .

4. Press and release the LCD “CODE” Key.

CODE

P<P

SCREEN

5. Display will show the Mode Setup Screen.

Press and release desired Mode key (TV, VCR,

SAT, etc.) on the rubber keypad.

Setup Screen - Mode

SETUP

MODE

EXIT

KEY?

- 46 -

Setup Screen - Code

4

7

2

5

SETUP

8

3

6

9

6. Display will show the Code Setup Screen.

Enter the 3 digits of the Device Code from the Library Code Tables. For a valid Code, the LED blinks off after the last digit is entered. For an invalid Code, the LED will flash rapidly for three seconds before going off. In both cases, the display will return to the Main Setup Screen.

0

CODE

EXIT

SEARCH

KEY?

7. Press and release the LCD “EXIT” key to return to normal operation.

8. Point the remote in the direction of your TV and press the POWER key.

Your device should turn off. Check other functions (for example for a

VCR : FF or REW etc.). If certain functions are not responding this indicates that the entered code is not the correct one. In that case repeat the above procedure with the next corresponding code of your brand.

9. Direct Library Code entry now complete

10.Repeat this procedure for the other appliance you want to control (TV,

VCR, DVD, SAT, CD, CBL, AUDIO and AUX)

- 47 -

7) Programming using Brand Search Method

It is possible to search for your appliance’s code by entering the brand of the appliance you wish to control.

Setup Screen - Main

SETUP SLEEP

1. Make sure your appliance is switched on. If not switch it on manually

2. Press and hold Setup key until the LED

MACRO remains on (occurring after approximately 2-

3 seconds) and display shows Main Setup

Screen.

LEARN

CODE

P<P

EXIT

SCREEN

3. Release Setup key.

4. Press and release the LCD “CODE” Key.

Setup Screen - Mode

5. Display will show the Mode Setup Screen. Press and release desired Mode key (TV, VCR, SAT, etc.) on the rubber keypad. Note the Brand

Search Method is not available for CD/Audio appliance.

SETUP

MODE

EXIT

KEY?

- 48 -

6. Display will show the Code Setup Screen.

Using the Table blow, press and release the numeric key (0-6) corresponding to desired

Setup Screen - Code

Manufacturer. Note – pressing “0” carries out a full library search same as normal Code Search

Method.

2

SETUP

3

4 5 6

Digit Conrad

Key Brand

7 8 9

Press Search

1 PHILIPS

0

CODE

EXIT

2 SONY

SEARCH

KEY?

3 THOMSON

4 SABA

5 GRUNDIG

6 NOKIA

7. Press and release the LCD “SEARCH” Key.

8. Display will show the Search Setup Screen.

Press the LCD “UP” key (or Power or Play) repeatedly until the Device to be controlled changes channel. Alternatively, you can use the

Channel Up & Down keys. Press and release the LCD “OK” (or Mute) key to install the Code.

Display will return to the Main Setup Screen.

If you accidentally overshoot the Code required, press the LCD “DOWN” or Channel Down to backtrack through the Library to return to the correct code. Pressing the LCD “UP” key (or

Power or Play) will change direction to forward again.

Setup Screen - Search

SEARCH

SETUP

OK

EXIT

KEY?

- 49 -

9. Repeat this procedure for any other appliance you want to control

(TV, VCR, DVD, SAT, CD, CBL, AUDIO and AUX).

10. The Code Search Method entry is now complete. Press and release the LCD “EXIT” key to return to normal operation.

Notes : a. When all codes under a Brand have been searched the LED will “error” flash indicating end of search and Main Setup Screen will be displayed. b. The above search procedure assumes that you want to store VCR codes under the VCR key, Cable codes under CBL, etc. If you want, for example, to store a VCR code under CBL, etc., then the Mode key must be “primed” for the new appliance. First follow the “Programming using 3 Digit Code Table” procedure and then enter any VCR code prior to carrying out the above search steps.

8) Programming using Manual Code Search

If you are unable to find your code either in the Code Tables or by using the Brand Search Method, you can try all the available codes for the appliance using the Manual Code Search.

Setup Screen - Main

1. Make sure your appliance is switched on. If not switch it on manually.

SETUP

MACRO

LEARN

SLEEP 2. Press and hold Setup key until the LED remains on (occurring after approximately 2-

3 seconds) and display shows Main Setup

Screen.

Release Setup key.

CODE

P<P

EXIT

SCREEN

3. Press and release the LCD “CODE” Key.

- 50 -

4. Display will show the Mode Setup Screen. Setup Screen - Mode

Press and release desired Mode key (TV, VCR,

SAT, etc.) on the rubber keypad.

SETUP

MODE

KEY?

EXIT

Setup Screen - Code

4

7

SEARCH

2

5

8

0

SETUP

CODE

KEY?

3

6

9

EXIT

5. Display will show the Code Setup Screen.

Press and release the LCD “SEARCH” Key.

- 51 -

6. Display will show the Search Setup Screen.

Press the LCD “UP” key (or Power or Play) repeatedly until the Device to be controlled changes channel. Alternatively, you can use the

Channel Up key. Press and release the LCD

“OK” (or Mute) key to install the Code. Display will return to the Main Setup Screen.

If you accidentally overshoot the Code required, press the LCD “DOWN” or Channel Down to

Setup Screen - Search

SETUP

OK backtrack through the Library to return to the correct code. Pressing the LCD “UP” key (or

Power or Play) will change direction to forward again.

SEARCH

EXIT

KEY?

7. Repeat this procedure for any other appliance you want to control (TV,

VCR, DVD, SAT, CD, CBL, AUDIO and AUX).

8. The Code Search Method entry is now complete. Press and release the

LCD “EXIT” key to return to normal operation.

Notes : a. When all codes have been searched the LED will “error” flash indicating end of search and Main Setup Screen will be displayed. b. The above search procedure assumes that you want to store VCR codes under the VCR key, Cable codes under CBL, etc. If you want, for example, to store a VCR code under CBL, etc., then the Mode key must be “primed” for the new appliance. First follow the “Programming using 3 Digit Code Table” procedure and then enter any VCR code prior to carrying out the above search steps. c. If the Device does not have a Channel Up key, use the Play (VCR &

CD/Audio only) or the Power keys instead. d. Code Search will start from the currently stored three digit number under that Mode e.g. if the Mode has 100 codes and the currently stored code is 050 then the Code Search will start from 051 continuing to 100 before looping back to 000 and finishing at 050. This simplifies the search process by allowing you to bypass codes already tried.

- 52 -

4

9) Identifying codes found using the search procedures

Setup Screen - Main

SETUP

MACRO

SLEEP

1. Press and hold Setup key until the LED remains on (occurring after approximately 2-

3 seconds) and display will show the Main

Setup Screen.

2. Release Setup key.

LEARN

CODE

P<P

EXIT

SCREEN

3. Press and release the LCD “CODE” Key.

Setup Screen - Mode

4. Display will show the Mode Setup Screen.

Press and release desired Mode key (TV, VCR,

SAT, etc.) on the rubber keypad.

SETUP

Setup Screen - Code

MODE

EXIT

2

5

SETUP

3

6

KEY?

7 8

0

CODE

9

EXIT

5. Display will show the Code Setup Screen.

Press and release Setup key.

SEARCH

KEY?

- 53 -

6. Display will show the Code Identification

Screen (Initially blank except for “SETUP”,

“INFO” and “CODE” labels). The display will now show the code using the LCD digits. The

3 digits will be shown in sequence for 1second each followed by a 0.5second gap where no digits are shown. The LED will blink off for each digit display. This sequence will only be carried out once then display will return to the

Main Setup Screen.

7. Code Identification is now complete. Press and release the LCD “EXIT” key to return to normal operation.

10) Programming a Macro

Setup Screen - Code ID

4

7 i

2

5

SETUP

8

0

CODE

3

6

9

Blink Back Digits

The Macro function allows you to store several sequences of IR

Commands (key presses). One press of the Macro key will execute the whole sequence. A total number of 20 keystrokes can be stored under each of the 9 available Macro keys.

Setup Screen - Main

SETUP

MACRO

LEARN

SLEEP

EXIT

1. Press and hold Setup key until the LED remains on (occurring after approximately 2-

3 seconds) and the display shows the Main

Setup Screen.

2. Release Setup key.

3. Press and release the LCD “MACRO” Key.

CODE

P<P

SCREEN

- 54 -

4. The Macro Setup Digit Screen will be shown.

Press and release the digit key the Macro is to be stored under.

Setup - Macro Mode

SETUP

MACRO

MODE

KEY?

EXIT

Setup Screen - Macro1

4

7

2

5

SETUP

MACRO

8

KEY?

3

6

9

EXIT

5. The Macro Mode Setup Screen will be shown. The first key stored in a Macro must be a Mode key. Press and release desired

Mode key (TV, VCR, SAT, etc.) on the rubber keypad.

- 55 -

6. Display will show the Macro Key Setup Screen.

This screen comprises the current screen labels for that Mode plus the SETUP and MACRO LCD labels will be shown. Press and release the remote keys (maximum of 20) that are required to be stored in the exact order that they should be transmitted. Use the LCD “SCREEN” key to toggle the screen keys displayed and use the

Mode keys for any Mode changes. The Setup key can be used to add delays – see separate notes. These are all counted as keystrokes.

Setup Screen - Macro2

TV

4

DSP

T-C

LEVEL

TUNER

VCR

2

SETUP

STB

5

AUX

OK

MACRO

DVD

3 S

SLEEP

TAPE

6

EFFECT

7. To store the Macro, press and release the rubber

“MACRO” Key. Display will return to the Main

Setup Screen. Note - if you program the maximum of 20 keys, then the Macro will be automatically stored on the 20 th keypress.

CD

7

MENU

AUDIO

8

0 FAV

DISC

9

USER1

A B AV

LEARN

MODE

USER2

10

EXIT

Mode Screen

SEARCH P<P

ENTER i

SV/V+

GUIDE

KEY?

SCREEN

8. Macro key programming now completed. Press and release the LCD

“EXIT” key to return to normal operation.

Macro Notes :

1. “SHIFTED” key commands are not allowed to be included in Macros.

2. There is an automatic delay of 0.5 second between each IR transmission in the sequence.

3. It may be necessary to have “delays” included in the Macro sequence

(e.g. to allow your TV warm-up time). Pressing the Setup key can include delays. The display will show the Macro Delay Setup Screen for digit selection. Press the digit for the required delay (in seconds) e.g. to enter a delay of 4 seconds, press and release Setup followed by

4. The maximum delay is 9 seconds. An “EXIT” key entry will give the default 0.5second delay. A delay is counted as one keystroke.

4. Pressing the Setup key twice allows for the User to abort and exit the

Macro routine. First Setup keypress takes you to the “Delay” screen and the second Setup press results in abort and exit.

- 56 -

5. It is not possible to include a Macro within a Macro.

To Delete a Macro :

1. Press and hold the Setup key until the LED remains on (occurring after approximately 2-3 seconds) and the display shows Main Setup

Screen.

2. Release Setup key.

3. Press and hold either the LCD or rubber MACRO key. The LED will blink off to indicate the keypress acceptance and the Macro Delete

Setup Screen will be shown. Only set Macros will be shown.

4. Press and release the digit key for the Macro that is to be deleted. The

LED will blink off and the Macro is deleted. Use the EXIT key to abort if required.

5. Macro deletion is now complete.

11) Channel toggle key

The Channel-Toggle “P<P” key is a special form of Macro key. The feature allows you to program in two specific channels and switch between them with a single key-press. For example, you may want to switch between TV channels 123 and 456. Programming the “P<P” key will allow you to do this.

Two sets of data are to be entered. Each set of data can be up to 4 keypresses and must be a minimum of 2. The first keypress in each set must be a Mode key. The following keystrokes can be any other key (except for

Mode, Macro, Setup and Screen) although in practice, these keys will usually be digit keys. Note no “shifted” commands can be part of a “P<P” sequence and a SCREEN keypress counts as a keystroke.

- 57 -

To Program the Channel-Toggle Feature

:

Setup Screen - Main

SETUP

MACRO

LEARN

SLEEP

1. Press and hold Setup key until the LED remains on (occurring after approximately

2-3 seconds) and display shows the Main

Setup Screen.

2. Release Setup key.

3. Press and release the LCD “P<P” Key.

CODE

P<P

EXIT

SCREEN

4. Display will show the “P<P1” Mode Setup

Screen. Press and release desired Mode key

(TV, VCR, SAT, etc.) on the rubber keypad.

Setup Screen - P<P 1

SETUP

MODE

EXIT

P<P

KEY?

- 58 -

Setup Screen - P<P2

TV

TUNER

4

DSP

CD

7

A B i

T-C

LEVEL

USER1

AV

MENU

REPEAT

SEARCH

SV/V+

VCR

2

SETUP

STB

5

MACRO

AUDIO

8

LEARN

0

AUX

OK

MODE

FAV

CODE

P<P

GUIDE

KEY?

DVD

3 S

SLEEP

TAPE

6

EFFECT

DISC

9

USER2

10

EXIT

ENTER

SCREEN

5. Display will show the “P<P2” Setup Screen.

This screen comprises the current screen labels for the Mode plus the SETUP and

“P<P” LCD labels will be shown. You can now press up to 3 keys (a minimum of 1 key must be pressed). Use the “SCREEN” Key to toggle the screen keys displayed – this counts as a keypress. When 3 keys are entered you will automatically continue to

Step 6. If less than 3 keys are required then press the Mode key and go directly to Step 6.

6. To enter the second set of data, press and release desired Mode key (TV, VCR, SAT, etc.) on the rubber keypad.

Setup Screen - P<P2

TV

TUNER

4

DSP

CD

7

A B

T-C

LEVEL

USER1

AV

MENU

REPEAT

VCR

2

SETUP

STB

5

MACRO

AUDIO

8

LEARN

0

AUX

OK

MODE

FAV

CODE

DVD

3 S

SLEEP

TAPE

6

EFFECT

DISC

9

USER2

10

EXIT

ENTER

7. Display will again show the “P<P2” Setup

Screen. You can now press up to 3 keys (a minimum of 1 key must be pressed) for the second set of data. Use the “SCREEN” Key to toggle the screen keys displayed – this counts as a keypress. When 3 keys are entered you will automatically continue to

Step 8. If less than 3 keys are required then press the Setup key and go directly to Step

8.

SEARCH i

SV/V+

P<P

GUIDE

KEY?

SCREEN

8. Display will return to the Main Setup Screen. Channel Toggle “P<P” setting routine now complete. Press and release the LCD “EXIT” key to return to normal operation.

9. To activate the Channel-Toggle function, Press and release the LCD

“P<P” key repeatedly to alternate between the two sets of data you entered.

- 59 -

12) Setting Key Labels :

You can select which keys are shown or “hidden” in the display for each of the Device Modes. You can select any LCD key for change except for the

SCREEN, SLEEP, SEARCH and P<P keys.

Setup Screen - Main

SETUP

MACRO

SLEEP

1. Press and hold Setup key until the LED remains on (occurring after approximately

2-3 seconds) and display shows the Main

Setup Screen.

2. Release Setup key.

LEARN

CODE

EXIT

3. Press and release the LCD “SCREEN” Key.

P<P

SCREEN

4. Display will show the Mode Setup Screen. Press and release desired Mode key (TV, VCR, SAT, etc.) on the rubber keypad.

Setup Screen - Mode

SETUP

MODE

KEY?

EXIT

- 60 -

Setup Screen - SCREEN

TV

TUNER

4

DSP

CD

7

LEVEL

USER1

A B

MENU

REPEAT

SEARCH i

T-C

AV

SV/V+

VCR

2

SETUP

STB

5

MACRO

AUDIO

8

LEARN

0

AUX

OK

MODE

FAV

CODE

P<P

GUIDE

KEY?

DVD

3 S

SLEEP

TAPE

6

EFFECT

DISC

9

USER2

10

EXIT

ENTER

SCREEN

5. Display will show the SCREEN Setup

Screen. This screen comprises the current screen labels for the Mode plus the SETUP and SCREEN LCD labels will be shown.

You can now press any of the LCD panel keys within the current Mode to select the individual key label display required. Use the

“SCREEN” Key to toggle the screen keys displayed. To Exit, pressing the Setup or

Mute keys will save changed key label selections and display returns to the Main

Setup Screen. If you want to edit another

Mode’s key labels then press the other Mode key - the Mode you were in is saved and display changes to the new Mode for any

Label changes.

6. Key Label change routine now complete. Press and release the LCD

“EXIT” key to return to normal operation.

Notes :

1. To reset the displayed Modes key labels back to their Default settings, press and hold the current Mode key for approximately 3 seconds at

Step 4 above until the Main Setup Screen is shown.

2. These labels are not displayed as part of the Key Label change routine

– “SLEEP”, “SETUP”, “MACRO”, “LEARN”, “P<P”, “KEY?” and

“SEARCH”.

- 61 -

13) Code Learning :

It is possible to learn IR commands (up to 40 keys per Mode) from your original remote.

Tips On Learning :

1. Always use of fresh batteries for the CV1000 and original remote

2. Carry out a Master Reset before attempting any Learning. Note this will reset all User programming back to factory defaults.

3. Place the original remote to the base of the Touchscreen so the IR LED on the original remote is in line with the Touchscreen opto-diode input

(See graphic below).

4. Keep the distance between the two remotes to about 5 cm.

5. Experiment by Learning 2 or 3 keys initially and then carry out a Master

Reset before completely Learning your original remote’s keyboard.

6. Do not attempt to Learn directly under an incandescent or low-energy light.

7. When Learning a key, do not release the key being Learned until the display returns and the LED remains on. This can take 2-3 seconds.

8. No functions may be stored under the LCD SCREEN, SLEEP, P<P,

SEARCH keys or under rubber keys Setup, Macro, TV, VCR, DVD,

CBL, SAT, CD, AUX or Audio keys. It is not possible to learn under

“shifted keys”.

3 to 5 cm

- 62 -

To Learn Commands :

Setup Screen - Main

SETUP

MACRO

LEARN

CODE

P<P

SLEEP

EXIT

1. Press and hold Setup key until the LED remains on (occurring after approximately 2-

3 seconds) and the display shows the Main

Setup Screen.

2. Release Setup key.

3. Press and release LCD “LEARN” Key.

SCREEN

4. Display will show the Mode Setup Screen.

Press and release desired Mode key (TV,

VCR, SAT, etc.) on the rubber keypad.

Setup Screen - Mode

SETUP

MODE

KEY?

EXIT

- 63 -

Setup Screen - Learn1

TV

4

DSP

T-C

LEVEL

TUNER

VCR

2

SETUP

STB

5

AUX

OK

MACRO

DVD

3 S

SLEEP

TAPE

6

EFFECT

5 Display will show the Learn Setup Screen.

This screen comprises the current labels for the Mode along with the SETUP and LEARN

LCD labels. Press and release the remote key to be taught with the original remote key code. Use the LCD “SCREEN” Key to toggle the screen keys displayed.

CD

7

USER1

A B AV

MENU

REPEAT

SEARCH i

SV/V+

AUDIO

8

LEARN

0

MODE

FAV

CODE

P<P

GUIDE

KEY?

DISC

9

USER2

10

EXIT

ENTER

SCREEN

6. Press and hold the original remote key until the Setup Screen - Learn3

LED blinks off once and the display shows the

Learn Next Setup Screen (this process can take up to 2 or 3 seconds to complete). If there is a problem with learning the LED will flash for three seconds but still remain in the

Learn routine with the Learn Next Setup

Screen displayed. To learn another key, press and release the LCD “LEARN” Key and repeat from Step “5”. To save and exit from the Learn routine, press and release the LCD “OK” Key.

Return to the Main Setup Screen.

7. Learning now complete. Press and release the

LCD “EXIT” key to return to normal operation.

SETUP

OK

LEARN

KEY?

- 64 -

To Clear all stored Learned Commands under a Mode :

Setup Screen - Main

1. Press and hold Setup key until the LED

SETUP SLEEP remains on (occurring after approximately

2-3 seconds) and display shows the Main

Setup Screen.

MACRO

LEARN

2. Release Setup key.

3. Press and release the LCD “LEARN” Key.

CODE

P<P

EXIT

SCREEN

4. Display will show the Mode Setup Screen.

Press and release desired Mode key (TV,

VCR, SAT, etc.) on the rubber keypad. The

LED will blink off once to indicate the keypress acceptance.

Setup Screen - Mode

SETUP

MODE

KEY?

EXIT

- 65 -

Setup Screen - Learn1

TV

4

DSP

T-C

LEVEL

TUNER

VCR

2

SETUP

STB

5

AUX

OK

MACRO

DVD

3 S

SLEEP

TAPE

6

EFFECT

5. Display will show the Learn Setup Screen.

Press and hold the Setup Key until the Main

Setup Screen is displayed. All Learned

Command entries under that Mode are now cleared.

CD

7

USER1

AUDIO

8

LEARN

DISC

9

USER2

A B i

AV

MENU

REPEAT

SEARCH

SV/V+

0

MODE

FAV

CODE

P<P

GUIDE

KEY?

10

EXIT

ENTER

SCREEN

Master Clear - To Clear all stored Learned Commands (recommended on first time Learning)

1. Carry Steps 1 and 2 same as above.

2. Press and hold the LCD “LEARN” Key until the Main Setup Screen is displayed (after approx. 5 seconds). All Learned Command entries are now cleared.

14. EXTRA FUNCTIONS :

1. Keypress Acknowledge Beep Feature :

It is possible to get an audible feedback of key-presses. When any key is pressed, the remote will generate a beep acknowledging the keypress.

The Keypress Acknowledge feature can be toggled on or off as follows :

1. Press and hold Setup key until the LED remains on (occurring after approximately 2-3 seconds) and the Main Setup Screen is shown.

2. Release Setup key.

- 66 -

3. To disable the beep, press and hold the rubber Stop key until the LED blinks. To enable the Beep, press and hold the rubber Play key until the LED blinks.

4. Beep Feature now toggled On or Off and the Main Setup Screen is shown.

2. LCD Panel & Backlight On-Time :

The LCD Panel display and Backlighting will remain on for a User selectable time period (10, 20, 30,……90 seconds). Power-on default is

30 seconds from last keypress. To set the LCD/Light On time :-

1. Press and hold Setup key until the LED remains on (occurring after approximately 2-3 seconds) and the Main Setup Screen is shown.

2. Release Setup key.

3. Press and release the Setup key. The LED will blink to acknowledge the keypress and the “9” Digit Setup Screen will be shown.

4. Press and release a digit key 1-9 (1=10 seconds, 2=20seconds, etc).

The LED will blink to acknowledge the keypress and the display will return to the Main Setup Screen.

5. LCD/Light On time setting now complete.

3. User Master Reset :

To reset the remote defaults back to factory settings.

1. Press and hold Setup key until the LED remains on and display shows the Main Setup Screen.

2. Release Setup key.

3. Press and hold the Setup key for approximately 5 seconds until the

LED blinks on then turns off.

4. Default Reset now complete and remote will be in normal TV Mode.

- 67 -

4. Channel Scan/Search Key (LCD) :

The Channel Scan/Search function is only available in TV, DVD, CBL/SAT and CD/Audio Modes. Pressing the LCD “SEARCH” Key allows the User to sequentially scan up available program channels. This key cannot be learned.

When pressed, a Channel Up command for the Current Mode code is sent once every 3 seconds. When any other key is pressed the scan will stop.

Scanning will automatically time-out after 2 minutes if no key is pressed.

5. VideoPlus/Showview Key (LCD) :

This key allows the User to directly access their VCR VideoPlus or

Showview function if the feature is available on their VCR. If VideoPlus or

Showview feature is not available then this key will allow direct access to any VCR Timer or Menu operation (if present) as an alternative. The

VideoPlus/Showview function is only available in VCR programmed

Modes. This key can be learned if required.

6. All Power Off Feature :

If the Power key is pressed consecutively twice within a 1second period, and the second Power key-press is held for greater than 2 seconds, then the remote will send the Power command for all Modes.

7. TV Volume/Mute Punch-Through :

The TV Volume/Mute punch-through feature allows the User to control the

Volume and Mute function of their Television in any Mode programmed to be a VCR (inc. DVD), Cable or SAT library device without the need to change to TV Mode. This feature is also available if AUX Mode is programmed to control a second VCR, Cable or SAT device.

- 68 -

8. CBL/SAT Volume Control :

Some Cable and Satellite have their own volume control. By default in

CBL/SAT modes, the CV1000 Volume and Mute key control the TV volume. To change the volume and mute control either to TV or CBL/SAT for CBL/SAT mode, proceed as follows :

1. Press and release the TV mode key (TV must be in TV mode for this procedure).

2. Press and hold setup key until the LED remains on and the Main Setup

Screen is shown.

3. Release Setup key.

4. Press and hold the Mute key for approximately 5 seconds. The LED will blink, and stay off for the 5second period then blink once more to indicate volume toggle acceptance. The display will return to the main

Setup Screen.

5. Remote Volume default is now set.

15 PROBLEMS AND TROUBLESHOOTING

. The remote doesn’t work or looses codes entered

Confirm with your original remote that the equipment works correctly

Make sure that you have pressed the corresponding mode key of the equipment or device that you want to control.

If the listed code does not work, try the AUTOSEARCH method or enter the next code of that brand.

To find the corresponding code for your equipment use the automatic search.

· Check that the batteries have the correct polarity position.

The programming of the remote requires 2 AAA batteries (new). If the remote looses codes within a few days/weeks the problem can be solved by using 2 new batteries from the same brand.

· If the LED is lit permanently, in general it will be necessary to replace the batteries.

Important:

The CV 350-2 must be used only in the way described in this instruction manual and may not be used for a purpose not intended.

- 69 -

CE Konformitätserklärung

X10 Europe 3 Rue de Penthièvre 75008 Paris France, erklaert hiermit, dass die nachfolgenden beschriebenen Produkte:

Universal Fernbedienung CV1000 mit den Sicherheits Anforderungen der » R&TTE directive 1999/5/EC « in Verbindung mit

Radio Uebertragung, EMC und Elektrischer Sicherheit uebereinstimmen

Die Ueberpruefung der Uebereinstimmung des Produktes mit den grundlegenden

Anforderungen des Artikels 3 R&TTE erfolgte auf Basis des Annex IV der Direktive

1999/5/EC und den folgenden Standards :Radio : EN 300 220-1-3, EMC : ETS 301 489-3,

Elektrische Sicherheit : EN 60 950

F.Rossi

0536

Date: 24.06.2002

Approval engineer

CE DECLARATION OF CONFORMITY

We, X10 Europe 3 Rue de Penthièvre 75008 Paris France, herewith declare that the following designated product :

Universal Remote Control CV1000

Complies with the essential protection requirements of the R&TTE directive 1999/5/EC on the approximation of the laws of the Member States relating to Radio Spectrum Matters,

EMC and Electrical Safety.

Assesment of compliance of the product with requirements relating to the essential requiremtns acc. to article 3 R&TTE was based on annexe IV of the Directive 1999/5/EC and the following standards :

Radio : EN 300 220-1-3, EMC : ETS 301 489-3, Electrical Safety : EN 60 950

0536

Datum: 24.06.2002

F.Rossi

Approval engineer

DECLARATION DE CONFORMITE CE

Nous, X 10 Europe 3 Rue de Penthièvre 75008 Paris France, déclarons que le produit suivant:

Télécommande Universelle Infrarouge CV1000 est en conformité avec les exigences essentielles applicables et en particulier celle de la directive 1999/5/CE et des normes suivantes:

Article 3.1a: Norme EN 60 950, Article 3.1b: Norme ETS 301 489-3, Article 3.2: Normes

EN 300 220-1-3

Procédure suivie: Annexe IV de la Directive 1999/5/EC

F.Rossi

0536

Date: 24.06.2002

- 105 -

Approval engineer