Incra TS Router Table Support Kit Owner Manual

Assembly Instructions for the INCRA TS Router Table Support Kit

Fig. 1 Fully assembled TS router table support kit

Fig. 2 Parts List

Table stiffener (2)

1/4-20 rectangular nut (8)

Table support bracket (4)

1/4” flat washer (8)

1/4” lock washer (8)

1/4-20 x 1/2 hex bolt (8)

Parts List

(2) Table stiffeners

(4) Table support brackets

(8) 1/4-20 x 1/2 hex bolts

(8) 1/4” flat washer

(8) 1/4” lock washer

(8) 1/4-20 rectangular nuts

(18) #10 x 3/4 wood screws

(22) #10 washer (includes 4 extras)

#10 washer (22)

#10 wood screw (18)

Step 1. Assemble the (8) bolt assemblies

The bolt assemblies are used for attaching the table support brackets to the TS rails. Each assembly consists of a 1/4-20 x 1/2 hex bolt, 1/4” lock washer,

1/4” flat washer and 1/4-20 rectangular nut. (See

Fig. 3)

Fig. 3 Bolt assemblies www.incra.com

Made in America by:

Taylor Design Group, Inc.

PO Box 810262

Dallas, TX 75381

Phone: 972-242-9975

1/4-20 rectangular nut (8)

1/4 washer (8)

1/4 lock washer (8)

1/4 hex bolt (8)

1

Step 2. Install support brackets on TS rails

Slide (2) pairs of the bolt assemblies (that were put together in Step 1 ) into the inside T-slot on each of the (2) TS rails. Drop the (4) rail support brackets on the (4) pairs of bolt assemblies. (See Fig. 4 ) Finger tighten only.

Position the support brackets on each rail so that each bracket will be located about 3 inches from each edge of the router table that they will support. The final position of the support brackets will be determined in Step 4.

Fig. 4 Install support brackets on TS rails

Second - Drop (4) support brackets on bolt assemblies.

Finger tighten only.

First- Slide (4) bolt assemblies on each of the (2) TS rails

Step 3. Attach stiffeners to bottom of table

Turn the router table upside-down, then position one of the stiffeners 1” - 2” from the edge of the router table that will butt against the table saw. Position the second stiffener 2” - 5” from the router opening. Now drill 1/8” pilot holes and screw the stiffeners to the bottom of the table with the #10 phillips wood screws and

#10 washers.

DO NOT DRILL THROUGH

THE ROUTER TABLE .

TIP: When installing the stiffeners, place the router table upside down on the support brackets installed in Step 2. This places the table at a convenient working height.

Fig 5 Attach stiffeners to table

#10 wood screw

#10 washer

Stiffener

This edge of router table against table saw

1”- 2” from table saw edge of router table

2” -5” from router opening

Fig. 6

Step 4. Lower the router table onto the support brackets

Position the support brackets 2” - 4” from the left and right edges of the router table (See Fig. 6 ). For tables wider than 32”, the table support brackets can be positioned 4” - 8” from each edge.

Fig. 7

#10 fasteners

Step 5. Attach router table to support brackets

Drill 1/8” Pilot holes and secure the table to the support brackets with the #10 washers and #10 wood screws (see Fig. 7 ).

DO NOT

DRILL THROUGH THE TABLE . Try to avoid drilling a pilot hole under the table’s miter channel (if it has one). If this is unavoidable, you can prevent the #10 screw from projecting into the miter channel by using two #10 washers instead of just one on the #10 screw. (extras washers are supplied for this purpose).

Now, make a final adjustment to the height of each table support bracket to insure that the top of the router table is flush and level with the top of the saw table. A long straight edge is useful for this alignment.

2