BatteryMINDer 12248-A-ODY Battery Charger INSTRUCTION MANUAL

Below you will find brief information for Battery Charger 12248-A-ODY. The BatteryMINDer® 12248-A-ODY is an Odyssey-specific charger, maintainer and desulfator. It is designed for use with all 600, 900* and 1200* series Odyssey sealed lead-acid batteries, as well as two 6-volt batteries connected in series. The charger features an “At-The-Battery” temperature sensor, which helps to ensure that the battery is charged at the optimal temperature. It also includes a full-time desulfator, which helps to remove harmful sulfates from the battery plates.

PDF

Document

BatteryMINDer&Acirc;&copy;
Model 12248-A-ODY
DC CONNECTION PRECAUTIONS
a. Connect and disconnect DC output clips from battery only
after removing charger power cord from outlet.
b. Attach clips to battery posts and twist or rock back and
forth several times to make good contact. This tends to keep
clips from slipping off terminals and reduces risk of sparking.
FOLLOW THESE INSTRUCTIONS WHEN BATTERY
IS INSTALLED IN EQUIPMENT (VEHICLE, PWC,
BOAT, TRACTOR, ETC.) A SPARK NEAR BATTERY
MAY CAUSE BATTERY TO EXPLODE. TO REDUCE
RISK OF A SPARK NEAR BATTERY:
c. Position DC output cord to reduce risk of damage by hood,
door, covers, or moving engine parts.
d. Stay clear of fan blades, belts, pulleys, and other parts that
can cause injuries.
e. Check polarity of battery posts. POSITIVE (POS, P,+) usually
has a larger diameter than NEGATIVE -.
f. Determine which post of battery is grounded (connected)
to the chassis of equipment. If negative post is grounded see
Item N. If positive post is grounded see item P.
N. For negative grounded equipment, connect POSITIVE
(RED) clip from charger to POSITIVE (POS, P, +) ungrounded
post of battery. Connect NEGATIVE (BLACK) clip to vehicle
chassis or engine block away from battery. Do not connect clip
to carburetor, fuel lines, or metal body parts.
g. For positive ground equipment, connect NEGATIVE
(BLACK) clip from charger to NEGATIVE (NEG, N,)
UNGROUNDED POST OF BATTERY. Connect POSITIVE
(RED) CLIP to chassis or engine block away from battery.
Rev. D-050509
Page P/N VDC12248-A-ODY-MNL
">

Hello! I am an AI chatbot specifically trained to assist you with the BatteryMINDer 12248-A-ODY Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Odyssey-specific battery charger
Charger, maintainer and desulfator
Full-time desulfator
“At-The-Battery” temperature sensor
8A charger

Frequently asked questions

The BatteryMINDer 12248-A-ODY is designed for use with all 600, 900* and 1200* series Odyssey sealed lead-acid batteries, as well as two 6-volt batteries connected in series. *Maintainer only.

The BatteryMINDer 12248-A-ODY is designed specifically for Odyssey batteries and features an “At-The-Battery” temperature sensor, which helps to ensure that the battery is charged at the optimal temperature. It also includes a full-time desulfator, which helps to remove harmful sulfates from the battery plates.

The BatteryMINDer 12248-A-ODY is easy to use. Simply connect the charger to the battery, plug it into a standard electrical outlet and press the start button. The charger will automatically charge the battery and then go into a maintenance mode to keep the battery fully charged.