Remote Automation Solutions FB1200 Flow Computer Quick Start Guide
Mainos
Mainos
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Emerson FB1200 Flow Computer
Quick Start Guide
Remote Automation Solutions
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Device Safety Considerations
Reading these Instructions
Before operating the device, read these instructions carefully and understand their safety implications. In some situations, improperly using this device may result in damage or injury. Keep this manual in a convenient location for future reference. Note that these instructions may not cover all details or variations in equipment or cover every possible situation regarding installation, operation, or maintenance. Should problems arise that are not covered sufficiently in the text, immediately contact Customer Support for further information.
System Training
A well-trained workforce is critical to the success of your operation. Knowing how to correctly install, configure, program, calibrate, and trouble-shoot your Emerson equipment provides your engineers and technicians with the skills and confidence to optimize your investment. Remote Automation Solutions offers a variety of ways for your personnel to acquire essential system expertise. Our full-time professional instructors can conduct classroom training at several of our corporate offices, at your site, or even at your regional Emerson office. You can also receive the same quality training via our live, interactive Emerson Virtual Classroom and save on travel costs. For our complete schedule and further information, contact the Remote Automation Solutions Training Department at 800-338-8158 or email us at [email protected]
.
Protecting Operating Processes
A failure of this device — for whatever reason -- may leave an operating process without appropriate protection and could result in possible damage to property or injury to persons. To protect against this, you should review the need for additional backup equipment or provide alternate means of protection (such as alarm devices, output limiting, fail-safe valves, relief valves, emergency shutoffs, emergency switches, etc.). Contact Remote
Automation Solutions for additional information.
Returning Equipment
If you need to return any equipment to Remote Automation Solutions, it is your responsibility to ensure that the equipment has been cleaned to safe levels, as defined and/or determined by applicable federal, state and/or local law regulations or codes. You also agree to indemnify Remote Automation Solutions and hold Remote Automation
Solutions harmless from any liability or damage which Remote Automation Solutions may incur or suffer due to your failure to ensure device cleanliness.
Grounding Equipment
Ground metal enclosures and exposed metal parts of electrical instruments in accordance with OSHA rules and regulations as specified in Design Safety Standards for Electrical Systems , 29 CFR, Part 1910, Subpart S, dated: April
16, 1981 (OSHA rulings are in agreement with the National Electrical Code). You must also ground mechanical or pneumatic instruments that include electrically operated devices such as lights, switches, relays, alarms, or chart drives.
Important: Complying with the codes and regulations of authorities having jurisdiction is essential to ensuring personnel safety. The guidelines and recommendations in this manual are intended to meet or exceed applicable codes and regulations. If differences occur between this manual and the codes and regulations of authorities having jurisdiction, those codes and regulations must take precedence.
Protecting from Electrostatic Discharge (ESD)
This device contains sensitive electronic components which be damaged by exposure to an ESD voltage.
Depending on the magnitude and duration of the ESD, it can result in erratic operation or complete failure of the equipment. Ensure that you correctly care for and handle ESD-sensitive components. ii
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Safety First!
Never perform the installation/setup activities described in this document in a hazardous area.
Ensure the area is non-hazardous.
DANGER
EXPLOSION HAZARD: Never remove end cap(s) in a hazardous location. Removing end cap(s) in a hazardous location could result in an explosion.
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
Important
Use only batteries supplied with the flow computer or sold by Emerson as spare parts for this flow computer. If you substitute a battery you obtain elsewhere you will void your certification unless it is the identical part from the same manufacturer as that supplied with the flow computer from
Emerson.
DANGER
EXPLOSION HAZARD - Substitution of any components may impair suitability for Class I, Division 1 or Class I, Division 2.
DANGER
EXPLOSION HAZARD - Do not disconnect equipment unless power has been removed or the area is known to be non-hazardous.
1
2
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Required Tools
Certain tools and equipment are required for installing and servicing the flow computer.
Table 1: Required Tools
Tool
Torque wrench
2.5 mm hexagonal wrench
3 mm hexagonal wrench
9/16 in hexagonal wrench
1 1/16 in combination wrench
#1 Phillips-head screwdriver
#2 Phillips-head screwdriver
1/8 inch flat-head screwdriver
1/16-inch flat head screwdriver
Laptop PC running Field Tools with
FBxConnect configuration software
Use
For bolting/mounting the flow computer
For manipulating rotation set screw
For screw for M4 x 0.7 end cap retaining clamp (ATEX required)
For installing/removing ¾ in NPT conduit plugs
For installing/removing ¾ in NPT to M20 thread reducer
(ATEX required)
For screws on HMI module
For screws on other modules and boards
For 5.08 mm pitch terminal block connections
For 3.81 mm pitch terminal block connections
For software configuration
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Removing/Replacing the Retaining Clamp
For flameproof ATEX/IEC applications, each end cap includes a retaining clamp which screws down to prevent the end cap from being unscrewed.
Front End Cap with Retaining Clamp Fitted
1 End Cap
2 Screw
3 Retaining Clamp
Retaining Clamp in Place
To loosen or tighten the screw, use a 3mm hexagonal wrench. When tightening, torque to 12 inlbs (1.4 N m).
Retaining Clamp and Screw
3
4
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Removing the Front or Rear End Cap
The flow computer includes two threaded end caps (covers). The front end cap includes a window for viewing the HMI module, while the rear end cap provides access to the terminal plate for power and I/O wiring.
DANGER
EXPLOSION HAZARD: Never remove end cap(s) in a hazardous location. Removing end cap(s) in a hazardous location could result in an explosion.
1.
Remove the retaining clamp (if present). Grasp the end cap (front or rear).
Note
If you need more leverage to open or close an end cap than you can get with your hand, you can place a long screwdriver or other appropriate tool across the two notches in the end cap to act as a pry bar:
2.
Unscrew the end cap turning it counter-clockwise until the end cap comes off. Set it aside in a safe location.
Front End Cap Removing Front End Cap
Rear End Cap Removing Rear End Cap
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Replacing the Front or Rear End Cap
DANGER
EXPLOSION HAZARD: Never remove end cap(s) in a hazardous location. Removing end cap(s) in a hazardous location could result in an explosion.
1.
Grasp the end cap (front or rear).
2.
Carefully align the end cap threads with the threads of the enclosure.
Important
When replacing the rear end cap, ensure wires connecting to the terminal plate do not get crimped or caught between the end cap threads and the enclosure.
3.
Screw the end cap clockwise (eight full turns) until it is tightly sealed to the enclosure.
4.
Replace the retaining clamp (if applicable).
5
6
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Bolting Considerations
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
If the flow computer installation requires assembly of a process flange, manifold, or flange adapters, follow these assembly guidelines to ensure a tight seal for optimal performance characteristics of the flow computer.
Only use bolts supplied with the flow computer or sold by Emerson as spare parts. Refer to the figures, below, for common flow computer assemblies with the bolt length required for proper flow computer installation.
Note
For all other manifolds, contact your local Emerson Sales office or Emerson Impact Partner.
Bolts are typically carbon steel or stainless steel. Confirm the material by viewing the markings on the head of the bolt and referencing Table 2 . If bolt material is not shown in the table, contact your local Emerson representative for more information.
Transmitter with coplanar flange
Transmitter with coplanar flange and optional flange adapters
Transmitter with coplanar flange and optional flange adapters
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Use the following bolt installation procedure:
1.
Carbon steel bolts do not require lubrication. Stainless steel bolts are factory-coated with a lubricant to ease installation. Do not apply any additional lubricant when installing either type of bolt.
2.
Finger-tighten the bolts.
3.
Torque the bolts to the initial torque value using a crossing pattern. See Table 2 for initial torque value.
4.
Torque the bolts to the final torque value using the same crossing pattern. See Table 2 for final torque value.
5.
Verify that the flange bolts protrude through the sensor module before applying pressure.
Table 2: Torque Values for the Flange and Flange Adapter Bolts
Bolt material
Carbon
Steel (CS)
Head markings Initial torque
300 in. -lbs.
(33.9 N m)
Stainless
Steel (SST)
150 in. -lbs.
(16.9 N m)
Final torque
650 in. -lbs.
(73.4 N m)
300 in. -lbs.
(33.9 N m)
Proper Bolt Installation
1
2
Bolt
Sensor module
7
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Coplanar Mounting Kit
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
8
1 Tubular L-shaped bracket
2 3/8-16 x 1 ½ in socket head wire lockable screw (2) — Apply Killark® LUBG-6 anti-seize lubricant to threads.
Torque screws to 30 in-lbs (3.4 N m)
3 Split 3/8 lock washer (2)
4 5/16-18 keps nut (2). Apply Loctite® 222TM Low Strength Purple Threadlocker to nuts. Torque nuts to 30 inlbs (3.4 N m)
5 U-bolt bracket
6 2-inch diameter pipe U-bolt
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Inline Mounting Kit
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
1 Pipe mounting bracket
2 U-bolt 2 ½ inch diam. pipe (5/16-18 x 3.75 long)
3 5/16 flat lock washer (2)
4 5/16-18 300 series hex nut (2) - Apply Loctite 222 Low Strength Purple Threadlocker to threads. Torque nuts to 30 in-lbs (3.4 N m)
5 U-bolt clamp assembly - Apply Loctite 222 threadlocker to threads. Torque nuts to 30 in-lbs (3.4 N m)
9
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Traditional Flange Mounting Kit
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
10
1 2.0 in. pipe diam. U-bolt assembly (5/16-18 x 4.0 LG) with (2) nuts (item 3)
2 Mounting bracket
3 Apply Loctite 222 Low Strength Purple Threadlocker to nuts. Torque nuts to 30 in-lbs (3.4 N m)
4 7/16-20 x .625 cs/zinc cobalt screws (4). Torque to 30 in-lbs (3.4 N m)
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Terminal Plate
The terminal plate includes the various terminal blocks (TB) for power and I/O connections. The appearance of the terminal plate varies depending upon whether you have the optional 6channel expansion I/O board installed with 3.81 mm pitch connectors; when it is installed there are eight or nine connections per terminal block instead of six 5.08 mm pitch connections.
Compare your device to the pictures to see which terminal plate you have.
5.08 mm Pitch Connectors
11
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
3.81 mm Pitch Connectors
12
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Grounding
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
The flow computer includes a ground lug on the terminal plate.
1 Ground Lug
Once you have installed the unit, run a ground wire between the ground lug and a known good earth ground. You route the ground wire through one of the conduit fittings.
Use stranded copper wire to earth ground and keep the length as short as possible.
Clamp or braze the ground wire to the ground bed conductor (typically a stranded copper AWG 0000 cable installed vertically or horizontally).
Run the ground wire so that any routing bend in the cable has a minimum radius of
30.48 cm (12 inches) below ground and 20.32 cm (8 inches) above ground.
For more information on grounding or if your installation uses cathodic protection, refer to Site Considerations for Equipment Installation, Grounding, and Wiring
( D301452X012 ).
13
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Wiring Communications
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
Notes
You do not need to add termination resistors; you can configure termination through software selections in FBxConnect.
You should terminate all shields at chassis ground.
COM1
1 RS-232 port (COM1) on FB device
2 RS-232-port on external device
14
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
1 RS-485/422 (4-wire) port (COM1) on FB device
2 RS-485/422 (4-wire)-port on external device
1 RS-485 (2-wire) port (COM1) on FB device
2 RS-485 (2-wire) port on external device
15
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
COM1 (Unit does not have optional I/O):
16
1 RS-232 port (COM1) on FB device
2 RS-232-port on external device
1 RS-485/422 (4-wire) port (COM1) on FB device
2 RS-485/422 (4-wire) port on external device
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
1 RS-485 (2-wire) port (COM1) on FB device
2 RS-485 (2-wire) port on external device
COM2 (unit has optional I/O):
COM2 does have its own GND terminal.
1 RS-232 port (COM2) on FB device
2 RS-232-port on external device
17
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
1 RS-485 (2-wire) port (COM2) on FB device
2 RS-485 (2-wire) port on external device
COM2 (Unit does not have optional I/O):
COM2 does not have its own GND terminal. Use either GND terminal on the COM1 terminal block.
18
1 RS-232 port (COM2) on FB device
2 RS-232-port on external device
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
1 RS-485 (2-wire) port (COM2) on FB device
2 RS-485 (2-wire) port on external device
COM3 (Unit has optional I/O):
COM3 does not have its own GND terminal. Use either GND terminal on the COM1 terminal block.
1 RS-232 port (COM2) on FB device
2 RS-232-port on external device
19
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
1 RS-485 (2-wire) port (COM3) on FB device
2 RS-485 (2-wire) port on external device
COM3 (Unit does not have optional I/O):
COM3 does not have its own GND terminal. Use either GND terminal on the COM1 terminal block.
20
1 RS-232 port on external device
2 RS-232-port (COM3) on FB device
1 RS-485 (2-wire) port on external device
2 RS-485 (2-wire) port (COM3) on FB device
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
21
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Ethernet
The Ethernet port is located on the terminal plate.
22
Notes
The default IP address for the Ethernet port is 192.168.1.10; the default port is 20000 for
DNP3 communication.
A jumper enables/disables the Ethernet port; see the Emerson FB1200 Flow Computer
Instruction Manual (D30782X012) for details.
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Wiring I/O
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
Notes
You should terminate all shields at chassis ground.
When using the digital output to drive an inductive load (such as a relay coil), place a suppression diode across the load. This protects the DO from the reverse Electro-Motive
Force (EMF) spike generated when the inductive load is switched off.
23
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
CPU Base I/O (AIAO1&2, DIDO1&2) Wiring (when optional I/O also present)
24
4
5
6
1
2
A When wiring a 1-5 V Analog Input (AI), use configuration at left
B When wiring a 4-20 mA Analog Input (AI), use configuration at left
3
Field Device
Power Supply 30Vdc Max
500 mA load max
To AGND
To AIAOx
Dry contact
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
CPU Base I/O (AI/AO1&2, DI/DO1&2) Wiring (when optional I/O not present)
3
4
1
2
5
A When wiring a 1-5 V Analog Input (AI), use configuration at left
B When wiring a 4-20 mA Analog Input (AI), use configuration at left
6
Field Device
Power Supply 30Vdc Max
500 mA load max
To AGND
To AIAOx
Dry contact
25
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Optional 6-Channel Expansion I/O Board Wiring:
26
A When wiring a 1-5 V Analog Input (AI), use configuration at left
B When wiring a 4-20 mA Analog Input (AI), use configuration at left
1 Field Device
2 Power Supply 30Vdc Max
3 500 mA load max
4 To AGND
5 To AIAOx
6 Dry contact
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
2-Wire RTD (when optional I/O also present):
1 2-Wire RTD
3-Wire RTD (when optional I/O also present):
1 3-Wire RTD
27
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
4-Wire RTD
Note
The default configuration is 4-wire RTD; you can change the configuration in FBxConnect.
1 4-Wire RTD
28
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Wiring Power
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
The flow computer accepts DC power with an input voltage range from 5.7 to 30V. The amount of power required depends on installed options.
If your device includes the 6-channel expansion I/O board your terminal block includes eight connectors; if it does not, your terminal block includes six connectors.
Note
The two upper graphics show the wiring for units with the 6-channel expansion I/O board; the lower graphic shows wiring for units without this board.
DC Power
1 To External power supply
29
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Solar Power
1 To solar power
Note
The upper graphic shows wiring for units with the 6-channel expansion I/O board; the lower graphic shows wiring for units without this board.
30
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Connecting the Main Battery Pack
DANGER
EXPLOSION HAZARD: Ensure the area in which you perform this operation is non-hazardous.
Performing this operation in a hazardous area could result in an explosion.
If you purchased one of the battery/solar panel options, note that the device ships with the battery pack disconnected to preserve battery life. You need to connect the main battery pack before you place the device in service.
The device provides two battery connections, enabling you to hot-swap the battery pack in a non-hazardous location.
1.
Remove the front end cap by unscrewing it counter-clockwise.
2.
Loosen the four captive fastening screws that hold the HMI module. Carefully pull the module away from the flow computer and off the tab and set it aside.
3.
Connect the battery to either of the two connectors.
31
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
4.
Carefully slide the HMI module back onto the tab and tighten the four captive fastening screws.
5.
Reattach the end cap. Screw it clockwise (eight full turns) until it is tightly sealed to the enclosure.
32
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Replacing the Main Battery Pack
Periodically you must replace the main battery pack. FBxConnect provides a battery life indicator showing the number of days of usage to help you monitor battery life.
The device provides two battery connectors, enabling you to hot-swap the battery pack in a nonhazardous location. Slide out the first battery pack (leaving it connected), attach the new battery to the second (available) connector (so both batteries are connected), and then disconnect the old battery pack.
DANGER
EXPLOSION HAZARD: Do not replace batteries unless power has been switched off or the area is known to be non-hazardous. Batteries must only be changed in an area known to be nonhazardous.
WARNING!
There are no user-serviceable parts inside the battery pack. Do not open the battery pack as you may damage the battery pack or injure yourself.
Note
These cells are to be used only in devices where servicing of the cell circuit is performed by a trained technician.
Keep the replacement battery pack handy during the procedure.
1.
Remove the front end cap.
33
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
2.
Loosen the two captive fastening screws on the battery pack.
3.
Loosen the two bottom captive fastening screws on the HMI module. Leave the two top screws connected to the battery pack.
4.
Grasp the HMI module and gently pull it and the battery pack out of the enclosure, leaving the battery still connected.
34
5.
Connect the new battery to the open connector. Route the wires so they are in the recessed area. Make sure the wires don’t get caught in the end cap threads.
6.
Disconnect the old battery pack’s connector from the unit and set the old battery pack aside.
7.
Slide the new battery pack into the unit. Tighten its two captive fastening screws.
8.
Loosen the top captive fastening screws on the HMI module to separate it from the old battery pack.
9.
Align the HMI module with the new battery pack and the tab on the CPU carrier board (bezel).
Gently press the HMI module on, being careful not to pinch the battery wires. Tighten all four captive screws.
10.
Replace the front end cap. Screw it clockwise (eight full turns) until it is tightly sealed to the enclosure.
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Powering Up/Powering Down the Device
DANGER
Do not attempt to connect power or disconnect power from the unit in a hazardous area.
Ensure the area is non-hazardous. Failure to do so could result in an explosion.
1.
Remove the front end cap.
2.
Terminal block TB1 includes connections for DC power (+DCIN, -DCIN) and battery/solar power (+SPIN, -SPIN). Battery power (which is also used with solar power) has its own internal connection.
Plug in TB1 to activate DC or solar power. If your device uses an internal battery and it is not connected, connect it as discussed in Connecting the Main Battery Pack .
Unplug TB1 to deactivate DC or solar power. If your device uses an internal battery, disconnect the main battery.
3.
Replace the front end cap. Screw it clockwise (eight full turns) until it is tightly sealed to the enclosure.
This turns on (or turns off) power from an external power supply or from the battery pack/solar panel.
Note
When you turn power on, the backlight on the HMI module lights, momentarily turns off and then remains lit while the INPUT LED blinks. After approximately one minute the initialization process completes and the HMI starts to display live data.
35
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Installing Field Tools Configuration Software
You install Field Tools software (which included FBxConnect) on your PC to configure the device.
Important
Field Tools (including FBxConnect) is available as a free software download to registered SupportNet users. If you are not a registered SupportNet user, new accounts take up to 24 hours to process so plan accordingly.
AMS Device Configurator (which is part of Field Tools) is incompatible with AMS
Device Manager: they cannot reside on the same machine.
If you have a previous version of Field Tools already installed on your PC, uninstall it and reboot your PC before you install this new version.
Before beginning the installation, close all other applications.
Field Tools cannot reside on a computer running any component of OpenEnterprise
2.x, OpenEnterprise 3.x, OpenEnterprise Client/Server, or ObjectServer software.
TechView and other components of BSI_Config software cannot be installed on a computer running OpenBSI Network Edition versions older than 5.9 Service Pack 2.
You must have administrative privileges to install Field Tools.
You must disable User Account Control (UAC) prior to installing Field Tools (you can reenable it after a successful installation).
As part of the installation, software from both Eltima and MACTek ® is automatically installed. Depending upon your permissions, Windows may require you to confirm these installations before the installation can proceed.
1.
Right click on the installer file and choose Run as administrator from the pop-up menu. For details on minimum hardware/software requirements as well as more details on the installation steps see the Field Tools Quick Start Guide (D301703X412).
Note
During Field Tools installation, you must select the FBx support including FBxConnect option.
36
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
2.
After software installation re-boot, start Field Tools from either the Windows Start
Programs menu or (if you created it) from the desktop icon.
3.
Log onto Field Tools.
Important
The first time you log into Field Tools, complete the User name field with the default admin and leave the Password field blank. Then assign a new password when prompted.
See the Field Tools Quick Start Guide (D301703X412) for any questions you have on changing default passwords after installation.
37
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
Establish a Connection and Launch the Setup
Wizard
CAUTION
When making multiple FBxConnect connections to the same device (as with a remote and a local connection), be aware that the changes one connection makes to the device may not be immediately visible to other connections and may even require the other connections to restart
FBxConnect before changes become visible. For example, simple changes (such as changes to setpoints) may be immediately visible to all connections, but changing the number of meters, configuring I/O, adding/deleting menu items, or other major configuration changes may require re-establishing the connection using FBxConnect.
After you start Field Tools you connect to the device and launch the initial setup wizard.
For a serial connection, connect a serial cable between either COM1 or COM2 on the device and a serial port (or USB/serial adapter) on your PC.
WiFi ® connections are possible if you purchased the Mobile SCADA option and if your
PC supports wireless communication.
For Ethernet connections, connect a standard 10/100Base-T Category 5 shielded
Ethernet patch cable to the Ethernet port.
1.
Click Connections > Add connection.
38
2.
Choose FBx as the Device Platform.
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
3.
Choose a Connection Type
For serial: choose the PC Comm port (or the port for the USB/serial adapter).
For WiFi: choose the default WiFi Network. The format for the WiFi Network (SSID) is similar to WiFi Network: FBxxxx_serialnumber . Then you must enter the default Security
Key: EmersonFBXX00. The flow computer’s default IP Address for WiFi is 192.168.1.10.
Important
You must change the Security Key for your network to something that is different from the default or else anyone reading this document will know your key. If you are connected via IP, you must assign a unique IP address to each device.
For IP: Enter the default IP Address for the Ethernet port of 192.168.1.10
. (Your PC must be able to access this address.)
39
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
4.
Click Connect. Field Tools activates the connection and automatically launches the
FBxConnect tool.
5.
When prompted, enter admin for both the Username and Password.
Important
When you finish initial configuration activities, be sure you change the password for the admin user . Otherwise, anyone reading this document could gain access to your device.
6.
When FBxConnect opens, click Configure.
7.
Click Initial Setup to launch the setup wizard.
40
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
8.
Follow the on-screen instructions to configure the device. Click Apply or Next to proceed through pages of the wizard or click Previous to return to a previous page. When you are done, click Finish.
41
Emerson FB1200 Flow Computer Quick Start Guide
D301786X012
August 2020
For customer service and technical support, visit www.Emerson.com/SupportNet
Global Headquarters,
North America, and Latin America:
Emerson Automation Solutions
Remote Automation Solutions
6005 Rogerdale Road
Houston, TX 77072 U.S.A.
T +1 281 879 2699 | F +1 281 988 4445 www.Emerson.com/RemoteAutomation
Europe:
Emerson Automation Solutions
Remote Automation Solutions
Unit 1, Waterfront Business Park
Dudley Road, Brierley Hill
Dudley DY5 1LX UK
T +44 1384 487200 | F +44 1384 487258
Middle East/Africa:
Emerson Automation Solutions
Remote Automation Solutions
Emerson FZE
P.O. Box 17033
Jebel Ali Free Zone — South 2
Dubai U.A.E.
T +971 4 8118100 | F +971 4 8865465
Asia-Pacific:
Emerson Automation Solutions
Remote Automation Solutions
1 Pandan Crescent
Singapore 128461
T +65 6777 8211| F +65 6777 0947
© 2018-2020 Remote Automation Solutions, a business unit of Emerson Automation
Solutions. All rights reserved.
This publication is for informational purposes only. While every effort has been made to ensure accuracy, this publication shall not be read to include any warranty or guarantee, express or implied, including as regards the products or services described or their use or applicability.
Remote Automation Solutions (RAS) reserves the right to modify or improve the designs or specifications of its products at any time without notice. All sales are governed by RAS terms and conditions which are available upon request. RAS accepts no responsibility for proper selection, use or maintenance of any product, which remains solely with the purchaser and/or end-user.
Remote Automation Solutions
Lataa
Julkinen linkki päivitetty
Chattisi julkinen linkki on päivitetty. You may view and manage your chat links after registration here.
Dokumentin julkinen linkki
Mainos
