advertisement
Instructions-Parts
AirPro
™
Gravity
Feed Airspray Gun
312579F
ENG
Conventional, HVLP, and compliant guns for specialty industrial applications.
100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
Important Safety Instructions
Read all warnings and instructions in this manual. Save these instructions.
See page 3 for model information.
ll 2 G ti11095A
2
Related Manuals
Contents
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Gravity Feed without Cup . . . . . . . . . . . . . . . . . . 3
Gravity Feed with Plastic Cup . . . . . . . . . . . . . . . 3
Gravity Feed with 3M
™
PPS
™
Cup . . . . . . . . . . . 3
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Gun Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Conventional Guns . . . . . . . . . . . . . . . . . . . . . . . 5
HVLP Guns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Compliant Guns . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Ground the Gun . . . . . . . . . . . . . . . . . . . . . . . . . 6
Flush Before Using Equipment . . . . . . . . . . . . . . 6
Adjust Spray Pattern . . . . . . . . . . . . . . . . . . . . . . 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pressure Relief Procedure . . . . . . . . . . . . . . . . . 8
Apply Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Volatile Organic Compounds (VOC) Regulation . 8
Related Manuals
Daily Gun Maintenance . . . . . . . . . . . . . . . . . . . . . . 9
General Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Clean Gun and Cup . . . . . . . . . . . . . . . . . . . . . . . 9
Clean Nozzle and Air Cap . . . . . . . . . . . . . . . . . 10
Compliant Cleaning Methods . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fluid Inlet Fitting Replacement . . . . . . . . . . . . . 12
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Repair Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 20
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 20
Manual
313089
313091
313092
313093
313094
313096
313097
313098
313100
313101
313102
313103
Language
Chinese
Dutch
Finnish
French
German
Italian
Japanese
Korean
Portuguese
Russian
Spanish
Swedish
312579F
Models
Models
Gravity Feed without Cup
Conventional HVLP Compliant
Orifice
Size in. (mm) Model Series
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar) Model Series
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar) Model Series
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar)
0.055 (1.4) 289002 A
0.070 (1.8) 289003 A
N/A
N/A
289005
289006
A
A
29 (0.2, 2.0)
29 (0.2, 2.0)
289008
289009
A
A
35 (0.24, 2.4)
35 (0.24, 2.4)
Gravity Feed with Plastic Cup
Conventional HVLP Compliant
Orifice
Size in. (mm) Model Series
0.055 (1.4) 289011 A
0.070 (1.8) 289012 A
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar) Model Series
N/A
N/A
289014
289015
A
A
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar) Model Series
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar)
29 (0.2, 2.0)
29 (0.2, 2.0)
289017
289018
A
A
35 (0.24, 2.4)
35 (0.24, 2.4)
Gravity Feed with 3M
™
PPS
™
Cup
Conventional HVLP Compliant
Orifice
Size in. (mm) Model Series
0.055 (1.4) 289020 A
0.070 (1.8) 289021 A
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar) Model Series
N/A
N/A
289023
289024
A
A
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar) Model Series
Max.
HVLP/Compliant
Air Pressure psi (MPa, bar)
29 (0.2, 2.0)
29 (0.2, 2.0)
289026
289027
A
A
35 (0.24, 2.4)
35 (0.24, 2.4)
312579F 3
4
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. Refer back to these warnings. Additional, productspecific warnings may be found throughout the body of this manual where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode.
To help prevent fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
• Ground all equipment in the work area. See Grounding instructions.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.
• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See
Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.
• Check equipment daily. Repair or replace worn or damaged parts immediately.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your Graco distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or overbend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
312579F
Gun Selection
WARNING
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
• Gloves
• Hearing protection
Gun Selection
Conventional Guns
Excellent atomization and high production rates typically with some reduction in transfer efficiency.
HVLP Guns
An HVLP gun is a high transfer efficiency gun which limits the air pressure at the air cap to
10 psi (0.07 MPa, 0.7 bar) maximum. In some areas, an HVLP gun is required for compliance with environmental standards.
Compliant Guns
A compliant gun is a high transfer efficiency gun which has been tested to have a transfer efficiency greater than or equal to HVLP guns.
The Graco compliant guns have no restrictions on air cap pressures, but the gun inlet pressure must remain under 35 psi (0.24 MPa,
2.4 bar) to remain in compliance.
312579F 5
6
Setup
Setup
5. Connect the fluid supply to the fluid inlet fitting.
fluid inlet
• Check that your shop air provides adequate air flow. See Technical
Data, page 19, for minimum cfm
requirements.
• Recommended 5/16 in. (7.9 mm) ID hose, optional 3/8 in. (10 mm) ID air hose.
• Set shop air pressure regulator (not supplied) according to paint manufacturer’s recommendation. See maximum compliant air pressure on air cap.
• Make sure no air restrictions, such as low-volume cheater-valves, obstruct the air flow. If an air adjusting valve is desired, use a Graco adjustable air valve (234784).
F
IG
. 1 air inlet
Ground the Gun
ti11306A
Check your local electrical code for detailed grounding instructions.
1. Shut off the air supply.
2. Install a shutoff valve (not supplied) downstream of the air regulator to shut off gun air.
3. Install an inline air filter (not supplied) to clean and dry the gun air supply.
4. Connect a clean, dry, filtered air supply to
the air inlet fitting. See F IG . 1.
Ground the gun through connection to a
Graco-approved conductive air supply hose.
Flush Before Using Equipment
The equipment was tested with lightweight oil, which is left in the fluid passages to protect parts. To avoid contaminating your fluid with oil, flush the equipment with a compatible solvent before using the equipment. See Flush,
312579F
Setup
Adjust Spray Pattern
1. Rotate the air cap to achieve desired spray
6. To reduce fluid flow, turn the fluid control valve clockwise.
• If the fluid control valve is turned clockwise all the way, the gun will emit only air.
• If you cannot achieve the correct fluid flow with the fluid control valve, a different sized nozzle may be necessary. For smaller fluid flow, use the next size smaller nozzle. For a larger fluid flow, use the next size larger nozzle.
F IG . 2 ti4839a
2. To achieve full fan pattern, open the air control valve by turning the knob fully coun-
3. To create a round pattern, turn the pattern air off by turning the air control valve fully
4. Trigger gun and adjust gun air pressure.
Refer to Technical Data, page 19, for inlet
air pressure.
5. To establish the correct fluid flow, turn the fluid control valve counterclockwise until no restriction of the trigger movement is felt, then turn out another half turn.
7. Spray a test pattern. Evaluate the spray pattern size and atomization.
8. To achieve a narrow spray pattern, turn air control valve clockwise.
9. To improve atomization, reduce the fluid flow rate. Increasing the air pressure can improve atomization but may result in poor
Transfer Efficiency (TE) or non-compliant operation.
air inlet valve
F IG . 3
312579F air control valve fluid control valve ti11097a
7
8
Operation
Operation
Pressure Relief Procedure
1. Turn off the gun air supply.
2. Trigger the gun to relieve pressure.
Apply Fluid
CAUTION
Excessive atomizing air pressure can increase over-spray, reduce transfer efficiency, and result in a poor quality finish.
Regulatory agencies in certain states prohibit the operation of a spray gun above 10 psi
(69 kPa, 0.7 bar) atomizing air cap pressure.
1. Fill the cup with material. Do not fill past the full markings on cup.
2. Turn on the shop air to the gun. Set atomizing pressure with the gun fully triggered.
3. Adjust the pattern size and shape. See
4. To achieve the best results when applying fluid:
• Keep the gun perpendicular and
6 to 8 inches (150 to 200 mm) from the object being sprayed.
• Use smooth, parallel strokes across the surface to be sprayed with 50% overlap.
When using the HVLP spray gun, instead of a conventional airspray gun, you may need to use a slightly slower hand movement and make fewer passes with the gun to coat a part.
This is due to the reduced spray velocity produced by lower HVLP air pressures, along with a larger fluid particle size because there is less air to blow off solvents than is produced by conventional airspray. Take care to avoid runs or sags as you spray.
Volatile Organic Compounds
(VOC) Regulation
In certain states, spraying solvents that release
VOCs into the atmosphere when cleaning a spray gun is prohibited. To comply with these air quality laws, you must use a cleaning method that prevents the escape of VOC vapors into the atmosphere. See Compliant
Clean air line filters as directed by the manufacturer.
See Troubleshooting, page 11, if you
experience an irregular pattern.
312579F
Daily Gun Maintenance
Daily Gun Maintenance
General Tasks
Follow the Pressure Relief Procedure,
• Frequently lubricate the gun moving parts with a drop of non-silicone oil.
• Do not disassemble the spray gun if you are having a spray pattern problem. See
Troubleshooting, page 11, for information
on how to correct the problem.
• Clean the fluid and air line filters daily.
• Check for fluid leakage. Tighten fittings or replace equipment as needed.
CAUTION
Solvent left in gun air passages could result in a poor quality paint finish. Do not use any cleaning method that may allow solvent into the gun air passages.
• Do not point gun up while cleaning it.
• Do not wipe gun with a cloth soaked in solvent; wring out the excess.
• Do not immerse the gun in solvent.
Flush
Flush before using the equipment, before changing colors, and when you are done spraying. Use solvent that is compatible with gun wetted parts and with the fluid that will be sprayed.
2. Dispose of any paint in the cup.
3. Fill the cup with a small amount of solvent.
4. Spray into a grounded metal waste container until the equipment is clean.
5. Follow Pressure Relief Procedure,
Clean Gun and Cup
CAUTION
• Do not submerge gun in solvent. Solvent dissolves lubricant, dries out packings, and clogs air passages.
• Do not use metal tools to clean air cap holes as this may scratch them and distort the spray pattern.
• Use a compatible solvent.
2. Dampen a soft cloth with solvent and wring out the excess. Point the gun down and wipe off the outside of the gun and cup.
3. Make sure cup lid vent hole is clear.
4. Blow dry gun inside and out. Lubricate.
See Compliant Cleaning Methods,
page 10, to comply with air quality laws if
applicable.
See Compliant Cleaning Methods,
page 10, to comply with air quality laws if
applicable.
1. Follow Pressure Relief Procedure,
312579F 9
Daily Gun Maintenance
Clean Nozzle and Air Cap
1. Remove air cap (13), trigger gun, remove nozzle (11), and soak both in a compatible cleaning solution.
5. Install the retaining ring (14) and air cap (13).
CAUTION
Trigger the gun whenever you tighten or remove the nozzle. This keeps the needle tip away from the nozzle seating surface and prevents the tip from being damaged.
2. Clean air cap, nozzle, and front of the gun with a soft-bristle brush dipped into compatible solvent. Do not use a wire brush or metal tools.
3. Use a soft implement, such as a toothpick, to clean out air cap holes.
4. Trigger the gun while you install the fluid nozzle with the gun tool. Tighten the nozzle securely to 155-165 in-lb (17.5-18.6 N•m) to obtain a good seal.
When reassembling, make sure the air cap matches the color etched onto the side of the nozzle (gold, brown, grey, blue, etc.).
6. After cleaning the gun, lubricate the following parts with lubricant 111265 daily:
• fluid control valve threads
• trigger pivot pin
• fluid needle shaft
Compliant Cleaning Methods
1. Place spray gun in a gun washer that completely encloses the gun and components during cleaning, rinsing, and draining.
2. Spray solvent through the spray gun into a closed gun cleaning station.
10 312579F
Troubleshooting
Troubleshooting
Problem Cause
Spray Pattern Normal pattern.
Solution
No action necessary.
Right
Spray Pattern
Wrong
Heavy top or bottom
Dirty or damaged air cap or fluid nozzle.
Rotate air cap 180°.
If pattern follows air cap, problem is in air cap (13). Clean and inspect. If pattern is not corrected, replace air cap.
If pattern does not follow the air cap, the problem is with the fluid nozzle. Clean and inspect the nozzle. If the pattern is not corrected, replace nozzle.
Reduce air pressure and increase material viscosity.
Spray Pattern Pressure too high for viscosity of material being sprayed.
Wrong
Split pattern
Correct pattern by narrowing fan size with fluid control valve (8).
Spray Pattern Dirty or distorted air horn holes.
Clean and inspect air cap. If pattern is not corrected, replace air cap.
Wrong
Gun spitting Air getting into paint stream.
Check if cup is empty and fill.
Tighten fluid nozzle (11).
Check and tighten needle packing nut (17).
Check fluid nozzle (11) for damage.
Replace fluid inlet gasket (3)
Damaged fluid nozzle seal (19).
Replace seal (19).
Will not spray Cup is empty.
Fill cup.
Excessive air blowing back
Fluid control valve (8) turned too far clockwise.
Loose fluid nozzle (11).
Adjust valve (8) counterclockwise.
Tighten fluid nozzle (11).
Damaged fluid nozzle seal (19).
Replace seal (19).
312579F 11
Repair
Repair
Fluid Inlet Fitting Replacement
Follow Pressure Relief Procedure, page 8.
See Parts, page 14, for callout references.
Disassembly
1. Unscrew retaining ring (14) to remove air cap (13b). Check o-rings (13a and 13c) and replace if necessary.
2. Trigger gun while unscrewing nozzle (11) to prevent needle damage.
3. Check o-ring (19) and replace if necessary.
4. Remove fluid control valve (8), spring (26), needle (9), and nut (7). Inspect. Replace tip (9c), needle (9), and u-cup seal (20) as necessary. If replacing needle tip, use low strength thread adhesive on needle tip threads.
5. Remove spring (28) and push the air valve assembly (6) out the back of the gun.
Inspect. Replace air valve assembly (6) and u-cup seal (20) as necessary. Use tool
(33) to install u-cup seal.
6. Remove trigger nut (22), trigger pin (21), wave washer (18), and trigger (10).
7. Unscrew needle packing nut (17) and remove u-cup packing (16) and spreader (15).
8. Remove air control valve assembly (5).
Inspect and replace as necessary.
9. Remove air inlet valve assembly (27).
Inspect and replace as necessary.
PRESSURIZED EQUIPMENT HAZARD
• Fluid inlet gasket (3) must be replaced if fluid inlet fitting (4) is removed from spray gun.
• Failure to replace gasket (3) may result in air leakage into the fluid section causing a non-vented gravity cup to become pressurized.
1. Remove fluid inlet fitting (4).
2. Remove fluid inlet gasket (3) from gun body and discard.
3. Apply thread sealant to replacement fluid inlet fitting (4) threads.
4. Snap the fluid inlet gasket (3) securely onto the fluid inlet fitting (4).
5. Screw in fluid inlet fitting (4) and torque to
155-165 in.-lb (17.5-18.6 N•m).
6. Replace washer (28) as required.
12 312579F
Repair
Reassembly
1. Install air control valve assembly (5) with valve turned fully counterclockwise to outermost position. Torque to 85-90 in-lb
(9.6-10.2 N•m).
2. Install air inlet valve assembly (27) with valve turned fully counterclockwise to outermost position. Torque to 205-215 in-lb
(23.2-24.3 N•m).
3. Lubricate u-cup spreader (15) and u-cup packing (16). Install spreader (15) with tapered end facing rear of gun. Install u-cup packing (16) with open end facing front of gun. Install packing nut (17). Torque to
3 in-lb (0.3 N•m).
4. Install wave washer (18) with cupped side toward the gun body. Lubricate and apply thread retainer to trigger pin (10). Install trigger (10), trigger pin (21), and trigger nut (22). Torque to 15-20 in-lb
(1.7-2.2 N•m).
5. Install air valve assembly (6), spring (28), and nut (7). Torque to 175-185 in-lb
(19.8-20.9 N•m).
6. Install needle (9) and spring (26). Lightly lubricate and install fluid control valve (8).
7. Trigger gun while replacing nozzle (11).
Torque to 155-165 in-lb (17.5-18.6 N•m).
8. Install air cap assembly (13) and retaining ring (14).
17 16 15 ti11226a
312579F 13
Parts
Parts
8
3
7
8 20
3
28
3
5
6 10
6
37 4
5 9
20
3
3
18
3
21
3
19
11
9
13b
1
13c
3
26
9a
9b
4
9c
3 4 7
22
1
12
17
2 3
16
11
23
15
2 3
10
13a 14
36
11 ti11224a
11 10
27
3
1
2
Pull trigger before installing nozzle
(11).
Insert spreader (15) with tapered end facing rear of gun. Insert u-cup (16) with open end facing front of gun.
Apply lubricant.
5
4 Apply low strength thread retainer.
Apply thread sealant.
6
7
8
9
Torque to 85-90 in-lb (9.6-10.2 N•m).
Torque to 15-20 in-lb (1.7-2.2 N•m).
Torque to 175-185 in-lb (19.8-20.9 N•m).
Torque to 155-165 in-lb (17.5-18.6 N•m).
10
11
Install with valve assembly turned fully counterclockwise to outermost position.
Torque to 205-215 in-lb (23.2-24.3 N•m).
12
Torque to 3 in-lb (0.3 N•m).
14 312579F
Parts
Ref.
1
3
4
5
❄
❄
❄
6*
7*
†
★
Part No. Description Qty.
---
---
BODY, gun
GASKET, fluid inlet
289792 FITTING, fluid inlet, includes gasket
(item 3)
1
289796 VALVE, air control assembly
1
289039 VALVE, air, assembly 1
1
1
1 289052 NUT, air valve, u-cup assembly
289097 VALVE, fluid control
---
---
NUT, needle
NEEDLE
1
1
1
1
8
9
9a
9b
9c
10
289140 TRIGGER
11
13
17
18
✖
19 ★
20*
21 ✖
22
✖
23
13a ★◆✓
13b
★◆✓
13c
14
✓
15 ★ +
16
★
+
26•
(includes 13a-13c)
---
---
---
---
---
289793
---
111457
---
---
---
289451
---
WASHER
O-RING
RING, retaining
SPREADER, u-cup
PACKING, u-cup
NUT
WASHER, wave
O-RING
PACKING, u-cup
PIN, pivot
NUT, pivot pin
FITTING, air inlet
1
1
SPRING, compression 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Ref.
Part No. Description Qty.
27 289142 VALVE, assembly, air inlet
1
28*
29
33*
★
--SPRING, compression 1
289794 TOOL, gun
36
--TOOL, installation, seal
289452 NUT, air plug, not assembled
37
❖★
38
--WASHER, uhmw
289770 CUP, gravity, 650 cc
38a 289195 FILTER, cup
(not shown)
★
Included in Gun Repair Kit 289790.
1
1
1
1
1
✖
Included in Trigger Repair Kit 289143
(contains 5 of each part).
+ Included in Needle Packing Repair Kit
289455 (contains 5 of each part).
* Included in Air Valve Repair Kit 289408.
◆
Included in Air Cap Seal Kit 289791
(contains 5 of each part).
✓
Included in Retaining Ring Kit 289079.
❖
Included in Cup Gasket Repair Kit 289213
(pack of 10).
❄
Included in Gun Body Kit 289022.
† Included in Fluid Inlet Gasket Kit 24A560, package of 5 (purchase separately).
--- Not sold separately.
312579F 15
Accessories
Accessories
Cups
Part No. Description
289797 Cup, aluminum, 23 oz (650 cc)
289802 Cup, aluminum, 34 oz (1 liter)
289770 Cup, plastic, 23 oz (650 cc)
192407 Cup Holder
Repair Kits
Part No. Description
289455 Needle Packing Repair Kit
289790 Gun Repair Kit
289791 Air Cap Seal Kit
289143 Trigger Repair Kit
289408 Air Valve Repair Kit
289213 Cup Gasket Kit, 10 pack
289079 Retaining Ring Kit
289022 Gun Handle Replacement Kit
24A560 Fluid Inlet Gasket Kit, 5 pack
24C310 Nozzle O-Ring Kit, 5-pack
Air Valves
Part No. Description
234784 Air Control Valve with Gauge
235119 Gun Air Regulator Assembly
239655 Swivel Air Valve
Cleaning Kit
Part No. Description
105749 Cleaning Brush
111265 Gun Lubricant
15C161 Ultimate Gun Cleaning Kit
3M
™
PPS
™
Cups and Accessories
Part No. Description
234941 Cup and Collar, 6 oz, 8-pack
234771 Cup and Collar 25 oz, 8-pack
234937 Cup and Collar 32oz, 4-pack
234940 Lid and Liner, 6 oz, 50-pack
234772 Lid and Liner, 25 oz, 50-pack
234938 Lid and Liner, 32 oz, 25-pack
234942 Ratio Film, insert, 6 oz, 50-pack
15F531 Ratio Film, insert, 25 oz, 100-pack
234939 Ratio Film, insert, 32 oz, 100-pack
289486 Gravity Cup Assembly, 25 oz, includes cup, collar, lid, liner, and adapter
289795 Gravity Feed Adapter
15E470 Lid Dispenser
15E469 Liner Dispenser
15E467 Gun Tray
Test Gauge
Part No. Description
289803 HVLP Verification
Hoses
Part No. Description
239631 4 ft Air Whip Hose Assembly (5/16 in.)
239636 15 ft Air Hose Assembly (5/16 in.)
239637 25 ft Air Hose Assembly (5/16 in.)
16 312579F
Repair Kits
Repair Kits
Without Gravity Cup
Model Spray Type
Nozzle
Size in. (mm)
289002 Conventional 0.055 (1.4)
289003 Conventional 0.070 (1.8)
289005
289006
HVLP
HVLP
0.055 (1.4)
0.070 (1.8)
289008
289009
Compliant
Compliant
0.055 (1.4)
0.070 (1.8)
Air Cap
Kit
(13a-13c)
Nozzle
Kit
(11, 19)
Needle
Assembly Kit
(9a-9c)
Needle/
Nozzle Kit
(9a-9c, 11, 19)
Needle Tip
Kit
(9c, 5-pack)
289773
289773
289771
289771
289772
289772
289780
289767
289776
289801
289779
289559
289799
289786
289786
289786
289799
289799
289493
289494
289495
289496
289497
289498
288185
289001
289001
289001
288185
288185
With Gravity Cup
Model Spray Type
Nozzle Size in. (mm)
289011 Conventional 0.055 (1.4)
289012 Conventional 0.070 (1.8)
289014
289015
HVLP
HVLP
0.055 (1.4)
0.070 (1.8)
289017
289018
Compliant
Compliant
0.055 (1.4)
0.070 (1.8)
Air Cap Kit
(13a-13c)
289773
289773
289771
289771
289772
289772
Nozzle
Kit
(11, 19)
289780
289767
289776
289801
289779
289559
Needle
Assembly Kit
(9a-9c)
289799
289786
289786
289786
289799
289799
Needle/ Nozzle
Kits
(9a-9c, 11, 19)
Needle Tip Kit
(9c, 5-pack))
289493
289494
289495
289496
289497
289498
288185
289001
289001
289001
288185
288185
With 3M PPS Cup
Model Spray Type
Nozzle Size in. (mm)
289020 Conventional 0.055 (1.4)
289021 Conventional 0.070 (1.8)
289023
289024
HVLP
HVLP
0.055 (1.4)
0.070 (1.8)
289026
289027
Compliant
Compliant
0.055 (1.4)
0.070 (1.8)
Air Cap Kit
(13a-13c)
289773
289773
289771
289771
289772
289772
Nozzle
Kit
(11, 19)
289780
289767
289776
289801
289779
289559
Needle
Assembly Kit
(9a-9c)
289799
289786
289786
289786
289799
289799
Needle/ Nozzle
Kits
(9a-9c, 11, 19)
Needle Tip Kit
(9c, 5-pack))
289493
289494
289495
289496
289497
289498
288185
289001
289001
289001
288185
288185
Needle Tips
Grooves
Grooves
4
7
Needle Tip Kit
(5-pack)
288185
289001 ti14043a
312579F 17
Repair Kits
18 312579F
Technical Data
Technical Data
Maximum Air Inlet Pressure . . . . . . . . . . . . . . . . . . . . . 100 psi (0.7 MPa, 7 bar)
Maximum HVLP/Compliant Inbound Air Pressure:
HVLP gravity feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 psi (0.2 MPa, 2.0 bar)*
Compliant gravity feed. . . . . . . . . . . . . . . . . . . . . . . . . . 35 psi (0.24 MPa, 2.4 bar)*
Air Consumption:
Conventional Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 CFM at 43 psi (0.3 MPa, 3.0 bar)
HVLP Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 CFM at 29 psi (0.2 MPa, 2.0 bar)
Compliant Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 CFM at 35 psi (0.24 MPa, 2.4 bar)
Fluid and Air Operating Temperature Range
Spray Gun:
32°F to 109°F (0°C to 43°C)
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npsm (R1/4-19)
Weight with cup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 lbs (0.6 kg)
Sound Data:
Conventional
Sound pressure at 43 psi (0.3 MPa, 3.0 bar). . . . . . . . 79.52 dB(A)**
Sound power at 43 psi (0.3 MPa, 3.0 bar). . . . . . . . . . 88.05 dB(A)**
HVLP
Sound pressure at 29 psi (0.2 MPa, 2.0 bar). . . . . . . . 83.9 dB(A)**
Sound power at 29 psi (0.2 MPa, 2.0 bar). . . . . . . . . . 90.8 dB(A)**
Compliant
Sound pressure at 35 psi (0.24 MPa, 2.4 bar). . . . . . . 81.8 dB(A)**
Sound power at 35 psi (0.24 MPa, 2.4 bar). . . . . . . . . 88.7 dB(A)**
Gravity Cup Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 oz (0.68 liter) cup
Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 stainless steel, 17-4 PH stainless steel, PEEK, acetal, UHMWPE
* Produces 10 psi (0.07 MPa, 0.7 bar) spraying pressure at air cap.
** All readings were taken with the fan valve fully open (fan full size) at the assumed operator position. Sound power was tested per ISO 9614-2.
312579F 19
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by
Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts.
The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS
SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 312579
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2007, Graco Inc. is registered to ISO 9001 www.graco.com
Revised 09/2009
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project