Instructions

LD Series Enclosed

Hose Reels

313938T

EN

For dispensing air, water, antifreeze, windshield washer solvent, transmission fluid, oil and grease. Not recommended for outdoor use.

Not approved for use in European explosive atmosphere locations.

Part Numbers and Models: Pages 4

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

ti13505

2

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be aware that flammable fumes can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources, such as cigarettes and portable electric lamps.

• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.

• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

• Ground all equipment in the work area.

• Use only grounded hoses.

• If there is static sparking or you feel a shock, stop operation immediately.

Do not use equipment until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

SKIN INJECTION HAZARD

High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point dispense valve at anyone or at any part of the body.

• Do not put your hand over the end of the dispense nozzle.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage.

313938T

Warnings

WARNING

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

313938T 3

Models

4

Models

The last character of each Model No. indicates the hose reel color. For example: D = black. On the table below this last character is represented by the generic # symbol. For example, to show the complete model number for a black

HEL13# model hose reel, the # symbol in the table is replaced with “D”. The complete model number is: HEL13D.

D=Black, Swivel Bracket

K=Orange, Fixed Bracket

NOTES:

For Parts and Kits, including hoses, inlets and hose stops, see Parts starting on page 19.

Additional Technical Data is provided on pages 23 and 24.

BSPT

Model No.

24F789

24F790

24F791

24F792

24F793

24F794

24F795

24F796

24F797

BSPP

Model No.

24J126

24J127

24J128

24J129

24J130

24J131

24J132

24J133

24J134

26C106

NPT

Model No.

24H655

24H656

24H657

24H658

24H659

24H660

24H661

24H662

24H663

Application

Air Only

Air Only

Air / Water

Air / Water

Air / Water

Air / Water

Oil

Oil

Grease

Grease

Hose Size

1/4 in. x 35 ft.

6 mm x 10 m

14 in. x 50 ft.

6 mm x 15 m

3/8 in. x 35 ft.

10 mm x 10 m

3/8 in. x 50 ft.

10 mm x 15 m

1/2 in. x 35 ft.

12 mm x 10 m

1/2 in. x 45 ft.

12 mm x 14 m

3/8 in. x 35 ft.

10 mm x 10 m

1/2 in. x 35 ft.

12 mm x 10 m

1/4 in. x 35 ft.

6 mm x 10 m

1/4 in. x 35 ft.

6 mm x 10 m

Maximum Pressure

PSI Bar Mpa

250

250

17.2

17.2

1.7

1.7

250

250

250

250

17.2

17.2

17.2

17.2

1.7

1.7

1.7

1.7

1800

1800

5000

5000

124.0

124.0

345

345

12.4

12.4

34.5

34.5

BSPT Models with Bracket Only

Model No.*

HEL13#

HEL15#

HEL23#

HEL25#

HEL33#

HEL34#

HEM23#

HEM33#

HEH13#

24M275*

24M276*

24M277*

24Y202*

24Y203*

Application

Air Only

Air Only

Air / Water 3/8 in. x 35 ft.

10 mm x 10 m

Air / Water 3/8 in. x 50 ft.

10 mm x 15 m

Air / Water 1/2 in. x 35 ft.

12 mm x 10 m

Air / Water 1/2 in. x 45 ft.

12 mm x 14 m

Oil

Oil

Grease

Oil

Hose Size

1/4 in. x 35 ft.

6 mm x 10 m

14 in. x 50 ft.

6 mm x 15 m

3/8 in. x 35 ft.

1/2 in. x 35 ft.

1/4 in. x 35 ft.

1/2 in. x 35 ft.

10 mm x 10 m

12 mm x 10 m

6 mm x 10 m

12 mm x 10 m

AIr Only NA 8 mm x 15 m

Air / Water 3/8 in. x 35 ft.

10 mm x 10 m

Oil 1/2 in. x 35 ft.

12 mm x 10 m

PSI

250

Maximum Pressure

Bar Mpa

17.2

1.7

250

250

17.2

17.2

1.7

1.7

250

250

250

1800

1800

5000

17.2

17.2

17.2

124.0

124.0

345

1.7

1.7

1.7

12.4

12.4

34.5

750

150

250

1800



Must be ordered separately. See page 21 for additional information.

* Color choice option is not available for these models.

52.0

10.5

17.2

124.0

5.2

1.05

1.7

12.4

Inlet Kit 

24C437

24C437

24C438

24C438

24C438

24C438

24C440

24C441

24C442

24C441

24C437

24J254

24J256

 Included in package.

313938T

Installation

Installation

A ground wire (G)

, bleed-type master air valve (E) and fluid drain valve (H) are required in your system installation. These components help reduce the risk of serious injury, including electric shock and splashing in your eyes or on the skin.

• The ground wire must be connected to the pump grounding lug and to a true each ground according to your local code.

• The bleed-type master air valve

relieves air trapped between this valve and the pump after the air is shut off. Trapped air can cause the pump to cycle unexpectedly Locate the valve close to the pump.

• The fluid drain valve

assists in relieving fluid pressure in the displacement pump, hose and gun. Triggering the valve to relieve pressure may not be sufficient.

Typical Installation Layout

A

L

F

D

E

B

G

C

H J

K

.

F

IG

. 1

A Main air supply

B Pump air supply

C Air filter

D Air regulator

E Bleed-type master air valve (required)

F Pump

G Pump grounding wire (required)

H Thermal relief valve (required)

J Dump valve (required)

K Fluid shut-off valve

313938T

L Fluid line25A113

M Hose reel

N Dispensing valve

P Flexible inlet hose

M

N ti13981

K

P

5

6

Installation

Wall Mounting

To reduce the risk of injury, be sure the mounting surface is strong enough to support the reels, weight of the lubricants and stress caused by hard pulls on the

service hoses. See Technical Data, page 19 for

weights of hose reel assemblies.

1.

2.

3.

ti13506

4.

ti13507

3.0 m (10 ft) maximum to floor ti13508

6 mm (1/4 in.) minimum

313938T

5.

7.

ti13510

8.

6.

Align ti13511

Installation

CLICK

313938T 7

Installation

Overhead Mounting

To reduce the risk of injury, be sure the mounting surface is strong enough to support the reels, weight of the lubricants and stress caused by hard pulls on the

service hoses. See Technical Data, page 19 for

weights of hose reel assemblies.

1.

2.

3.

4.

3.0 m (10 ft.) maximum to floor

8

6 mm (1/4/ in.) minimum

313938T

5.

CLICK

6.

Align ti13511

7.

Installation

313938T 9

Installation

Flushing

Before installing meter or dispense valve to end of hose, flush supply line with a compatible solvent such as Stoddard solvent or mineral spirits.

1.

Place end of hose in waste container.

2.

Blow out entire lubricant supply line with air

3.

Flush equipment with a compatible solvent until fluid runs clear.

4.

Pump dispensing lubricant through line until all solvent is flushed out.

10 313938T

Repositioning Hose Stopper (optional)

1.

2.

Repositioning Hose Stopper (optional) ti13525

3.

313938T 11

Installing Meter

Installing Meter

1.

12 313938T

Adjusting Spring Tension

Adjusting Spring Tension

IMPACT HAZARD

The spring is always under great tension and could be propelled or uncoil with enough force to cause serious injury.

• The hose reel spring is not a serviceable part. Do not attempt to replace or service the spring.

• Always grasp ratchet handle firmly with both hands when adjusting tension.

• When decreasing spring tension, never attempt to turn ratchet more than 1/4 turn with each push-in motion.

Uncontrolled spinning of the hose reel could cause serious injury if you are hit by the hose or a tool.

• Never allow reel to spin freely.

• The reel must be bolted securely in place when making adjustments.

Increasing Tension

Table 1: Recommended Turns to Set and Decrease Spring Tension

Model

4

Approximate No. of Turns

Full Turns to Increase

Spring Tension

1/4 Turns to Decrease Spring

Tension

16 HEL13#, 24F735, 24F744, 24F753, 24F762,

24F771, 24F780, 24J258, 24J267, 24J276

HEL15#, 24F736, 24F745, 24F754, 24F763,

24F772, 24F781, 24J259, 24J268, 24J277,

24M277

HEL23#, 24F737, 24F746, 24F755, 24F764,

24F773, 24F782, 24J260, 24J269, 24J278

HEL25#, 24F738, 24F747, 24F756, 24F765,

24F774, 24F783, 24J261, 24J270, 24J279

HEL33#, 24F739, 24F748, 24F757, 24F766,

24F775, 24F784, 24J262, 24J271, 24J280

HEM23#, 24F741, 24F750, 24F759, 24F768,

24F777, 24F786, 24J264, 24J273, 24J282

HEM33#, 24F742, 24F751, 24F760, 24F769,

25A113, 24F787, 24J265, 24J274, 24J283

HEH13#, 24F743, 24F752, 24F761, 24F770,

24F779, 24F788, 24J266, 24J275, 24J284,

26C106

HEL34#, 24F740, 24F749, 24F758, 24F767,

24F776, 24F785, 24J263, 24J272, 24J281,

24M275, 24M276

3

4

4

4

5

7

6

4

12

16

16

16

20

28

24

16

313938T 13

Adjusting Spring Tension

1.

2.

ti13515

1/4

Turn

ti13516

14 313938T

Decreasing Spring Tension

Decreasing Spring Tension

1.

2.

Push in on ratchet. Grasp handle firmly with both hands; then turn ratchet counter-clockwise 1/4 turn

ONLY.

Repeat this procedure of pushing in and turning ratchet counter-clockwise, ONLY 1/4 turn at a time, until spring tension has been completely released.

See Table 1, page 13 for the recommended number

of 1/4 turns needed to completely release the spring tension.

1/8

Turn

Push In

ti13516

1/4 Turn

ONLY!

ti13517

3.

----------------------

1/8

Turn

Out

ti13518

313938T 15

Operation

Operation

16 313938T

Repair and Maintenance

Pressure Relief Procedure

1.

2.

Repair and Maintenance ti13524 ti13523

313938T 17

Repair and Maintenance

Disassembly

1.

2.

ti13512

3.

18 ti13513-2 ti13514

313938T

Parts

1d

1k

1 

1j

1e

1 

1j

1f/1g

1m

1‡

1c

1b

16

1a

24

6

19

Parts

23

2

8

11

15

12

7

32

31

30

29

25 28 17

27

26

TI14425

313938T 19

8

11

12

15

16

2

6

7

1 

1a‡ 

1b‡ 

1c‡ 

1d 

1e 

1f 

1g 

1h 

1j 

1k 

1m 

Ref Part No. Description

1‡

1 

Qty

15Y706

24E319

BRACKET, swivel, included in all HEL,

HEM and HEH models

BRACKET, fixed, included in models

24M275, 24M276, 24M277

16C019 BRACKET, fixed, bench mounted,

. CAP, mounting tube

. TUBE, mounting

. CLIP, button clip

. BRACKET, roller A

. BRACKET, roller B

. PIN, roller

. ROLLER, hose

. SCREW, machine, pan head

. WASHER

. BOLT

. NUT

SCREW, mach pan hd

ENCLOSURE (B)

ADJUSTER, power spring

SCREW, recessed pan hd

SPRING, adjuster

TUBE, shaft

CAP, shaft

SPOOL

1

1

1

3

1

1

1

1

11

1

1

2

2

1

2

1

2

1

1

1

Ref Part No. Description

17

Qty

262214

262216

262218

262220

262222

262232

262224

262226

262227

262584

262585

262586

262587

262588

262589

262590

262591

262592

24J295

24J296

24J297

FLEXIBLE, 1/4 in. x 35 ft (6 mm id x 10 m), BSPT, air

FLEXIBLE, 1/4 in. x 50 ft. (6 mm id x

15 m), BSPT, air

FLEXIBLE, 3/8 in. x 35 ft. (10 mm id x

10 m), BSPT, A/W

FLEXIBLE, 3/8 in. x 50 ft. (10 mm id x

15 m), BSPT, A/W

FLEXIBLE, 1/2 in. x 35 ft. (12 mm id x

10 m), BSPT, A/W

FLEXIBLE, 1/2 in. x 45 ft. (10 mm id x

14 m), BSPT, oil

FLEXIBLE, 3/8 in. x 35 ft. (10 mm id x

10 m), BSPT, oil

FLEXIBLE, 1/2 in. x 35 ft. (12 mm id x

10 m), BSPT, oil

FLEXIBLE ,1/4 in. x 35 ft. (6 mm id x

10 m), BSPT, grease

HOSE, 1/4 in. x 35 ft. (6 mm id x 10 m),

NPT, air

HOSE, 1/4 in. x 50 ft. (6 mm id x 15 m),

NPT, air

HOSE, 3/8 in. x 35 ft. (10 mm id x 10 m), NPT, A/W

HOSE, 3/8 in. x 50 ft. (10 mm id x 15 m), NPT, A/W

HOSE, 1/2 in. x 35 ft. (12 mm id x 10 m), NPT, A/W

HOSE, 3/8 in. x 35 ft. (10 mm id x 10 m), NPT, oil

HOSE, 1/2 in. x 35 ft. (12 mm id x 10 m), NPT, oil

HOSE, 1/4 in. x 35 ft. (6 mm id x 10 m),

NPT, grease

HOSE, 1/2 in. x 45 ft. (12 mm id x 14 m), NPT, A/W

HOSE, 1/4 in. x 35 ft. (6 mm id x 10 m),

BSPP, air

HOSE, 1/4 in. x 50 ft. (6 mm id x 15 m),

BSPP, air

HOSE, 3/8 in. x 35 ft. (10 mm id x 10 m) , BSPP, A/W

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

24J298

24J299

24J300

24J301

HOSE, 3/8 in. x 50 ft. (10 mm id x 15 m), BSPP, A/W

HOSE, 1/2 in. x 35 ft. (12 mm id x 10 m), BSPP, A/W

HOSE, 3/8 in. x 35 ft. (12 mm id x 14 m), BSPP, oil

HOSE, 1/2 in. x 35 ft. (10 mm id x 10 m), BSPP, oil

1

1

1

1

24J302

HOSE, 1/4 in. x 35 ft. (12 mm id x 10 m), BSPP, air

1

24J303

HOSE, 1/4 in. x 45 ft. (6 mm id x 10 m),

BSPP, A/W

1

24N175 HOSE, 8 mm id x 15 m, quick coupling 1

Parts

Ref Part No. Description

23

24

25

26

19

24C531

24C532

24C533

KIT, swivel, air, A/W (24F789, 24F790,

24F791, 24F792, 24F793, 24F794,

24J126, 24J127, 24J128, 24J129,

24J130, 24J131, 24M277, and HEL models)

KIT, swivel, oil (24F795, 24F796,

24J132, 24J133, 24M275, 24M276 and HEM models)

KIT, swivel, grease (24H797, 24J134, and HEH models)

24H474

KIT, swivel, air, A/W (models 24H655,

24H656, 24H657, 24H658, 24H659,

24H660)

24H475

KIT, swivel, air, A/W (models 24H661 and 24H662)

24H476 KIT, swivel, grease (model 24H663)

ENCLOSURE (A)

FITTING

ROLLER, hose guide

SCREW, mach, phil, pn hd

178029 STOP, hose, 1/2” od

178030 STOP, hose, 5/8” od 27

28

29

30

25E147 STOP, hose, 3/4” od

101324 NUT, hex, jam

SCREW, countersunk head

WASHER, id 6.4, od 18

31 LATCH

32 SPRING, latch

33  15W036 LABEL, Warning

Qty

1

1

1

1

1

1

1

2

2

1

1

1

2

2

1

2

2

1

1

 Replacement Danger and Warning labels, tags and cards are available at no cost.

Mounting Bracket Kits

‡ 24G866

KIT, Hose Reel Wall Mounting Bracket.

 24G865 KIT, Hose Reel Fixed Installation Kit.

 24C772 KIT, Hose Reel Bench Mounting Bracket.

Inlet Kits

Ordering the Correct Kit for Your Hose Reel

24C437 KIT, hose, 1/4”, air, BSPT

24C438 KIT, hose 3/8” and 1/2”, A/W, BSPT

24C440 KIT, hose 3/8” and 1/2” oil, BSPT

24C442 KIT, hose, 1/4”, grease, BSPT

24C441 KIT, hose 1/2”, oil, BSPT

24C443 KIT, hose 1/4”, air, NPT

24C444 KIT, hose, 3/8”, A/W, NPT

24C537 KIT, hose, 3/8” oil, NPT

24C538 KIT, hose, 1/2” oil, NPT

24C539 KIT, hose, 1/4”, grease, NPT

24J253 KIT, hose 1/4”, air, BSPP

24J254 KIT, hose, 1/2”, A/W, BSPP

24J256 KIT, hose, 1/2” oil, BSPP

24J257 KIT, hose, 1/4” oil, BSPP

313938T 21

Parts

Thread

BSPT

BSPT

BSPT

BSPT

BSPT

BSPT

BSPT

BSPT

NPT

NPT

NPT

BSPP

BSPP

BSPP

BSPP

BSPP

BSPT

NPT

NPT

NPT

NPT

NPT

NPT

BSPP

BSPP

BSPP

BSPP

BSPT

BSPP

*Includes bracket

Replacement Reel Hose Kit (17) Swivel Kit (19) Stop (27) Inlet Kit

24F789, HEL13#* 262214 24C531 178029 24C437

24F790, HEL15#*

24F791, HEL23#*

262216

262218

24C531

24C531

178029

178030

24C437

24C438

24F792, HEL25#*

24F793, HEL33#*

24M275*, 24M276*

24F794, HEL34#*

24F795, HEM23#*

24F796, HEM33#*

24M275, 24M276

24F797, HEH13#*

262220

262222

262232

262224

262226

24C531

24C531

24C531

24C532

24C532

178030 24C438

25E147

25E147

178030

25E147

24C438

24C438

24C440

24C441

24H655

24H656

24H657

24H658

24H659

24H660

24H661

24H662

24H663

24J126

24J127

24J128, 24Y202

24J129

24J130

24J131

24J132

24J133, 24Y203

24J134

24M277*

26C106

272227

262584

262585

262586

262587

262588

262592

262589

262590

262591

24J295

24J296

24J297

24J298

24J299

24J300

24J301

24J302

24J303

24N175

24J303

24C533

24H474

24H474

24H474

24H474

24H474

24H474

24H475

24H475

24H476

24C531

24C531

24C531

24C531

24C531

24C531

24C532

24C532

24C533

24C531

24C533

178029 24C442

178029 24C443

178029 24C443

178030

178030

25E147

25E147

178030

25E147

178029

178029

178029

178030

178030

25E147

25E147

178030

25E147

178029

178029

178029

24C444

24C444

24C444

24C444

24C537

24C538

24C539

24J253

24J253

24J254

24J254

24J254

24J254

24J255

24J256

24J257

24C437

24J257

22 313938T

Technical Data

Technical Data

Additional hose reel information, including Application, Hose Sizes and Maximum Working Pressure Ratings is pro-

vided on pages 4 and 4.

Models

H/24F = BSPT

Temperature

Range C° (F°)

Inlet

( BSPT,

NPT,

BSPP)

1/2 in.

HEL13#, 24F789,

24H655, 24J126

HEL15#, 24F790,

24H656, 24J127

HEL23#, 24F791,

24H657,

24J128,24Y202

HEL25#, 24F792,

24H658, 24J129

HEL33#, 24F793,

24H659, 24J130

HEL34#, 24F794,

24H660, 24J131

HEM23#, 24F795,

24H661, 24J132

HEM33#, 24F796,

24H662, 24J133,

24M275, 24M276,

24Y203

HEH13#, 24F797,

24H663, 24J134,

26C106

24M277

-10°C - 60°C

(14°F - 140°F)

-10°C - 60°C

(14°F - 140°F)

-17.8°C - 60°C*

(0°F - 140°F)

-17.8°C - 60°C*

(0°F- 140°F)

-17.8°C - 60°C*

(0°F - 140°F)

-17.8°C - 60°C*

(0°F - 140°F)

-17.8°C - 60°C

(0°F - 140°F)

-17.8°C - 60°C

(0°F - 140°F)

-17.8°C - 60°C

(0°F - 140°F)

-10°C - 60°C

(14°F - 140°F)

Sound Data All Models

Sound Pressure: 69.3 dB(A)†

1/2 in.

1/2 in.

1/2 in.

1/2 in.

1/2 in.

1/2 in.

1/2 in.

3/8 in.

1/2 in.

Outlet

( BSPT,

NPT,

BSPP)

Weight

1/4 in.

9.0 kg

19.8 lb

1/4 in.

9.5 kg

21 lb

3/8 in.

10.4 kg

23 lb

Wetted Parts

Aluminum, Buna-N Rubber, PVC

Aluminum, Buna-N Rubber, PVC

Aluminum, Buna-N Rubber

3/8 in.

11.0 kg

24.25 lb

1/2 in.

10.5 kg

23.1 lb

1/2 in.

11.4 kg

25.1 lb

3/8 in.

11.4 kg

25.1 lb

1/2 in.

14.0 kg

30.8 lb

1/4 in.

13.2 kg

29.1 lb

9.5 kg

21 lb

Aluminum, Buna-N Rubber

Aluminum, Buna-N Rubber

Aluminum, Buna-N Rubber

Carbon Steel, Buna-N Rubber, PTFE

Carbon Steel, Buna-N Rubber, PTFE

Carbon Steel, Buna-N Rubber

Aluminum, Buna-N Rubber, PU

Sound Power: 75.3 dB(A)†

*0°C - 60°C (32°F - 140°F) for Water Applications.

† Tested in accordance with ISO9614-2 with an assumed operator position.

313938T 23

Technical Data

Mounting Pattern

6 mm (1/4 in.) bolts

50 mm

(1.97 in.)

171 mm (6.73 in.)

Dimensions

650 mm

(25.6 in.)

470 mm

(18.5 in.)

180 mm

(7.1 in.)

24 313938T

Notes

Notes

313938T 25

Graco 5-Year Hose Reel Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period from the date of sale as defined in the table below, repair or replace equipment covered by this warranty and determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

Graco 5-Year Hose Reel Extended Warranty

Component

Structural Components

Power Spring

Wear Parts - including but not limited to hose, seals, swivel seats and roller guides

Bare reels - all components

Warranty Period

5 years

3 years

1 year

1 year

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within one (1) year past the warranty period, or two (2) years for all other parts.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents.

Original instructions.

This manual contains English. MM 313938

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2009, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revised May 2019