advertisement
INSTRUCTIONS-PARTS LIST
This manual contains important warnings and information.
READ AND KEEP FOR REFERENCE.
First choice when quality counts.
INSTRUCTIONS
308798
Rev. T
Displacement Pump
3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure
Model 239923, Series A
Used in the Ultra Max and Ultimate Mx 795 and 1095 Sprayers
Used in the GMax and GMx 3900 Sprayers
Model 240291, Series A
Used in the Ultra Max and Ultimate Mx 1595 Sprayers
Used in the GMax and GMx 5900 Sprayers
Used in the GMax 10000 Sprayers
Model 240917, Series A
Used in the GMax and GMx 7900 Sprayers
Model 240800, Series A
Used in the GMax 5900HD and Mark V Sprayers
Model 243344, Series A
Used in the LineLazer II 3900 Sprayers
Model 243345, Series A
Used in the LineLazer II 5900 Sprayers
8016A
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1997, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
Table of Contents
Warnings
Service
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
Technical Data
Parts, Pump
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
239923 and 243344 . . . . . . . . . . . . . . . . . . . . . . . . . . 16
240291 and 243345
240917
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
18
240800
Warranty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Graco Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Symbols
Warning Symbol Caution Symbol
WARNING
This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION
This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.
INSTRUCTIONS
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
This equipment is for professional use only.
Read all instruction manuals, tags, and labels before operating the equipment.
Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor.
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
Technical Data on page 15 for the maximum working pressure of this equipment.
Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use could result in a chemical reaction, with the possibility of explosion.
Comply with all applicable local, state, and national fire, electrical, and safety regulations.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the Pressure Relief Procedure on page 3 to prevent the equipment from starting unexpectedly.
2 308798
Service
Tools Needed Pressure Relief Procedure
WARNING
PRESSURIZED EQUIPMENT HAZARD
The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. To reduce the risk of an injury from accidental spray from the gun, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you: are instructed to relieve the pressure, stop spraying, check or service any of the system equipment, or install or clean the spray nozzle.
1.
Engage gun safety latch.
2.
Turn ON/OFF switch to OFF.
3.
Unplug power cord.
4.
Disengage gun safety latch. Hold metal part of gun against grounded metal pail and trigger gun into pail to relieve pressure.
5.
Engage gun safety latch.
6.
Open any fluid drain valves in system. Leave drain valve open until ready to dispense again.
Pump Repair Kit
Vise
12 in. adjustable, open end wrench (2)
Hammer, 20 oz maximum
Small screwdriver
Throat Seal Liquid
Pick or long small screwdriver
Cleaning and Inspecting Parts
1.
Clean and inspect parts. Pay particular attention to the ball seats in the intake valve and piston, which must have no nicks or wear, and to the inside of the sleeve and the outside of the piston rod, which must not be worn or scratched. Replace worn or damaged parts.
WARNING
COMPONENT RUPTURE HAZARD
Never use sharp or pointed tools to remove sleeve or other components which could result in pump rupture and cause serious bodily injury. If the sleeve cannot be removed easily, return the sleeve and cylinder to your Graco distributor for removal.
Pump
239923
240291
240917
240800
Repair Kit
239928
240248
240916
240248
2.
Remove and clean the sleeve when you are repacking the pump.
308798 3
Service
Repair When Pump Is Off The Sprayer
Disassembling the pump
Fig. 1. Remove packing nut (202) and throat adjustment spacer (228).
Fig. 3. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.
227
202
228
Fig. 3
7570A
Fig. 4. Tap piston rod out of cylinder with a hammer or flip over and tap piston rod out against a bench.
Note: Sleeve may come out of cylinder with piston rod.
7568A
Fig. 1
Fig. 2. Unscrew intake valve from cylinder.
Fig. 4
Fig. 5.
Remove piston rod from sleeve, or remove sleeve from cylinder.
7571a
Fig. 2
4 308798
7569A
Fig. 5
7572A
Service
Fig. 8. Remove throat packings and glands from cylinder. Discard throat packings and glands.
WARNING
COMPONENT RUPTURE HAZARD
Do not clean or wipe the piston valve threads. Cleaning the piston valve threads could destroy the special sealing patch and cause the piston valve to come loose during operation, causing pump bursting and possible serious bodily injury.
Used on
240291
240800
&
240917
Fig. 6.
Unscrew piston valve from piston rod. Clean and inspect parts. The piston has a special thread locking/sealing patch. Do not remove the patch. The patch allows four disassembly/assembly procedures before it is necessary to apply Loctite to the threads.
Fig. 6
7576A
Fig. 7. Remove packings and glands from piston rod.
Used on
240291
240800
&
240917
7573B
Fig. 8
Assembling the pump
Fig. 9. Soak all leather packings in SAE 30W oil for 1 hour minimum prior to assembly. Stack male gland
(219) on piston rod. Alternately stack UHMWPE (208) and leather (218) packings (note orientation) on piston rod. Install female gland (217). Install backup washer
(216) and u-cup (209) (note orientation) on piston valve (210). The special sealing patch on piston valve threads is good for four repackings. Use Loctite on piston valve threads after four repackings.
Used on
240291
240800
&
240917
210
216
209
217
7574B
Fig. 7
7574B Fig. 9
218 219 208
308798 5
Service
Fig. 10. Install ball (206) in piston rod. If Loctite is applied to piston valve threads, ensure that none gets on ball.
Fig. 12. Soak all leather packings in SAE 30W oil for 1 hour minimum prior to assembly. Place male gland
(204) in cylinder. Alternately stack UHMWPE (203) and leather packings (223) (note orientation). Place female gland (224) in top of cylinder. Seat packings.
206
224
Used on
240291
240800
&
240917
203 223
204
Fig. 10
7575A
Fig. 11. Tighten piston valve to piston rod as specified:
Torque to 27 +/–3 ft-lb
(239923)
Torque to 55 +/–3 ft-lb
(240291, 240800)
Torque to 55 +/–5 ft-lb
(240917)
Fig. 12 7573B
Fig. 13. Install seal (201) into packing nut (202). Install throat adjustment spacer onto packing nut. Loosely install packing nut into cylinder.
201
202
7581A
Fig. 11
7576A
Fig. 13
6 308798
Service
Fig. 14. Grease piston packings and sleeve top edge.
Fig. 16. Grease top inch or two of piston rod that will go through the cylinder throat packings.
Fig. 14
7578A
Fig. 15. Carefully slide piston assembly into top of sleeve. Assure u-cup is not rolled over or damaged.
Fig. 16
7579A
Fig. 17. Grease o-ring (221) and place on sleeve. Slide sleeve/piston rod assembly into bottom of cylinder. Replace o-ring (207) if desired.
Note: O-ring (207) is not required for safe pump operation.
Fig. 15
7577A
Fig. 17
221
207
7582A
308798 7
214
212
227
Service
Fig. 18. Reassemble intake valve with new o-ring
(227), seat (212) and ball (214). Seat may be flipped over and used on other side. Clean seat thoroughly.
Fig. 20. Torque seal and packing nut (202) down onto throat nut spacer (228) to 100 +/– 10 in-lb.
Remove throat nut spacer (228) when pump packings begin to leak after much use. Then tighten packing nut down until leakage stops or lessens. This allows approximately 100 gallons of additional operation before a repacking is required.
202
228
7570A
Fig. 18
Fig. 19. Install intake valve on cylinder. If a wrench is used torque as follows:
67 +/– 5 ft-lb (for model 239923)
80 +/– 5 ft–lb (for models 240291 & 240800)
150 +/– 5 ft–lb (for model 240917).
If a wrench is not used, be sure intake valve is bottomed out against cylinder.
Fig. 20
7568A
Fig. 19
8 308798
7569A
Notes
308798 9
Service
Repair When Pump Is On The Sprayer
WARNING
INJECTION HAZARD
To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pressure Relief
Procedure on page 3.
Fig. 2. Use screwdriver to push retaining spring up and push pin out.
Fig. 1. Remove intake valve.
Fig. 1
10 308798
7673A
7674A
Fig. 2
Fig. 3. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.
227
Fig. 3
7570A
Fig. 4. Remove piston rod and sleeve.
Service
Fig. 7. Invert piston rod and insert into cylinder to force out throat packings.
Fig. 4
7746A
Fig. 4. Invert piston rod and sleeve and pound on hard surface until piston rod comes out of sleeve.
Fig. 7
7747A
7572A
Fig. 8. Insert piston rod into cylinder with pin hole up and piston valve down. Insert pin into piston rod and crank shaft.
Fig. 5
Fig. 6. Remove packing nut (202)
202
7675A
7726A
Fig. 8
Fig. 6
308798 11
Service
Fig. 9. Remove piston valve from piston rod with a wrench.
Fig. 11. Soak all leather packings in SAE 30W oil for 1 hour minimum prior to assembly. Stack male gland
(204). Alternately stack UHMWPE (203) and leather
(223) packings (note orientation). Install female gland
(224). Install seal (201) and packing nut (202) and throat adjustment spacer (228).
203
224
223
Used on 240291,
240917 & 240800
201
202
228
204
Fig. 9
Fig. 10. Remove pin and piston rod from cylinder.
7748A
7573B
7581A
Fig. 11
Fig. 12. Remove packings and glands from piston rod.
Fig. 10 7675A
Fig. 12
Used on
240291
240800
&
240917
7749B
12 308798
Service
Fig. 15. Grease piston packings and sleeve top edge.
Fig. 13. Soak all leather packings in SAE 30W oil for 1 hour minimum prior to assembly. Stack male gland
(219) on piston rod. Alternately stack UHMWPE (208) and leather (218) packings (note orientation) on piston rod. Install female gland (217). Install backup washer
(216) and u-cup (209) (note orientation) on piston valve (210). The special sealing patch on piston valve threads is good for four repackings. Use Loctite on piston valve threads after four repackings.
219
Used on
240291
240800
&
240917
Fig. 13
218 208
217
209
216
210
7749B
Fig. 15 7578A
Fig. 16. Carefully slide piston assembly into top of sleeve. Assure u-cup is not rolled over or damaged.
Fig. 10. Install ball (206) in piston rod. If Loctite is applied to piston valve threads, ensure that none gets on ball. Install piston valve on piston rod.
Torque as follows:
27 +/– 3 ft-lb (for model 239923)
55 +/– 3 ft-lb (for model 240291 & 240800)
55 +/– 5 ft-lb (for model 240217)
Fig. 16
7577A
Fig. 17. Grease top inch or two of piston rod that will go through the cylinder throat packings.
206
Fig. 14
7575A
Fig. 17
308798
7579A
13
Service
Fig. 20. Push in pin.
Fig. 18. Grease o-ring (221) and place on sleeve. Slide sleeve/piston rod assembly into bottom of cylinder. Replace o-ring (207) if desired.
Note: O-ring (207) is not required for safe pump operation.
Fig. 20
7675A
Fig. 21. Reassemble intake valve with new o-ring
(227), seat (212) and ball (204). Seat may be flipped over and used on other side. Clean seat thoroughly.
204
212
227
207
221
7750A
Fig. 18
Fig. 19. Use screwdriver to push retaining spring up.
Fig. 21
Fig. 22. Install intake valve on cylinder.
Wrench torque as follows:
67 +/– 5 ft-lb (for model 239923)
80 +/– 5 ft-lb (for model 240291 & 240800)
150 +/– 5 ft-lb (for model 240917)
7570B
Note: Make sure retaining ring falls into slot.
Fig. 19
14 308798
7674B
Fig. 22
7678A
Service
Cross Sectional Reference
222
201
202
228
Pump 240291 & 240917
Leather
224
223
205
221
220
207
Leather
219
218
209
210
221
215
212
227
203 V-Max UHWMPE, blue
204
Pump 240291 & 240917
206
208
V-Max UHWMPE, blue
217
216
214
213
7683B
Fig 23
Technical Data
Maximum working pressure . . . . . . . . . . . . . . . . . . . . . . .
3600 psi (250 bar, 24.8 MPa)
Fluid inlet size
239923 & 240291
240917 & 240800
Fluid outlet size
. . . . . . . . . . . . . . . . . . . . . . 3/4 npt(f)
. . . . . . . . . . . . . . . . . . . . . . . . 1 npt(f)
239923 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
240291, 240217 & 240800 . . . . . . . . . . . . . .
1/4 npt(f)
3/8 npt(f)
Wetted parts . . . . . . . . . . . . . . . stainless steel, PTFE leather, polyurethane, zinc-plated carbon steel,
, tungsten carbide, chrome plating,
Delrin , polyethylene
NOTE : Delrin and PTFE
Loctite is a registered trademark of the Loctite Company.
308798 15
Parts – Pumps 239923 and 243344
Model 239923, Series A
201
Carbon Steel Displacement Pump
202
228 Ref
No.
Part No.
Description Qty.
224*
201 179810 SEAL, throat
202 193046 NUT, packing
203* 192692 V-PACKING, throat,
V-Max UHMWPE, blue
204* 178942 GLAND, male, throat
205 CYLINDER, pump
240522 Pump 239923
243346 Pump 243344
206* 105444 BALL, sst, 0.3125 in.
207* 114054 PACKING, o-ring
208* 192693 V-PACKING, piston
V-Max UHMWPE, blue
209* 107093 SEAL, u-cup
210 239932 VALVE, piston
212† 239922 KIT, seat, carbide includes 214 and 227
213 VALVE, intake (foot)
192724 Pump 239923
195892 Pump 243344
214*† 105445 BALL, sst, 0.5000 in.
215 192624 GUIDE, ball
216* 181338 WASHER,
217* 178969 GLAND, female, piston
218* 178939 V-PACKING, leather, piston
219* 192848 GLAND, male
220 240521 SLEEVE,
221* 108526 O-RING, PTFE
222 240518 ROD,
223* 178940 V–PACKING, leather, throat
224* 178943 GLAND,
227*† 107079 PACKING, o-ring
228 192714 SPACER, throat, nut
* These parts are also included in Repair Kit 239928, which may be purchased separately.
2
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
3
1
1
1
3
1
1
1
1
1
*223
220
203*
204*
205
207*
221*
*208
†*214
†*227
† These parts are also included in Carbide Seat Kit
239922, which may be purchased separately.
221*
222
219*
212†
213
7567B
218*
217*
209*
216*
206*
210
215
16 308798
Parts – Pumps 240291 and 243345
Model 240291, Series A
201
Carbon Steel Displacement Pump
202
228
Ref
No.
Part No.
Description Qty.
224*
201 183171 PLUG
202 193032 NUT, packing
203* 193124 V-PACKING
V-Max UHMWPE, blue
204* 183176 GLAND, packing, male, throat 1
205 CYLINDER, pump
240520 Pump 240291
243347 Pump 243345
1
1
1
1
4
206* 101947 BALL, sst, 0.3750 in.
207* 106556 PACKING, o-ring
208* 193125 V-PACKING, piston
V-Max UHMWPE, blue
209* 108690 SEAL, u-cup
1
1
4
1
1
1
210 240150 VALVE, piston
212† 244199 SEAT, carbide
213 includes 214 and 227
HOUSING, intake (foot)
193030 Pump 240291
195895 Pump 243345
214*† 102972 BALL, sst, 0.875 in.
215 193027 GUIDE, ball
216* 186653 WASHER,
217*
218*
219*
183185
183174
183178
GLAND, female, piston
V-PACKING, leather, piston
GLAND, packing, male
220 240525 SLEEVE,
3
1
1
1
1
1
1
1
221* 107098 PACKING,
222 240517 ROD,
223* 183175 V-PACKING, throat
224* 183177 GLAND, packing, female
227*† 108526 PACKING, o-ring
228 193127 SPACER, nut
1
1
1
1
2
1
3
* These parts are also included in Repair Kit 240248, which may be purchased separately.
*203
223*
204*
205
207*
221*
220
*218
†*214
†*227
† These parts are also included in Carbide Seat Kit
244199, which may be purchased separately.
221*
222
219*
212†
213
7953A
208*
217*
209*
216*
206*
210
215
308798 17
Parts – Pump 240917
Model 240917, Series A
Carbon Steel Displacement Pump
Ref
No.
Part No.
Description
201 112590 PLUG
202 189589 NUT, packing
203* 193722 V-PACKING
V-Max UHMWPE, blue
205 240920 CYLINDER, pump
206* 107203 BALL, sst, 0.3750 in.
207* 107306 PACKING, o-ring
209* 112589 SEAL, u-cup
210 240580 VALVE, piston
212† 240918 SEAT, carbide includes 214 and 227
213 198121 HOUSING, intake (foot)
214*† 107167 BALL, sst, 0.875 in.
215 193391 GUIDE, ball
216* 195488 GUIDE, piston
217* 189588 GLAND, female, piston
218* 112591 V-PACKING, leather, piston
219* 189585 GLAND, packing, male
220 240921 SLEEVE, cylinder
221* 108822 PACKING,
222 240919 ROD,
224* 194175 GLAND, packing, female
227*† 107098 PACKING, o-ring
228 193397 SPACER, nut
229 195523 PIN
230 194060 CLIP, retaining
231 162485 NIPPLE, adapter
232 114967 COUPLING
235 244823 TUBE, intake includes 232
Qty.
1
1
8
1
1
1
1
1
1
1
1
2
1
2
1
1
6
1
1
1
1
1
1
1
1
1
1
*203
201
202
228
224*
218*
219*
229*
230
231
205
207*
221*
* These parts are also included in Repair Kit 240916, which may be purchased separately.
† These parts are also included in Carbide Seat Kit
240918, which may be purchased separately.
220
*218
1 *216
†*214
†*227
221*
222
219*
203*
217*
209*
206*
210
215
212†
213
232
235
1 Assemble piston guide (216) with lip toward piston (210)
8557d
18 308798
Parts – Pump 240800
Model 240800, Series A
Carbon Steel Displacement Pump
Ref
No.
Part No.
Description Qty.
201 183171 PLUG
202 193032 NUT, packing
203* 193124 V-PACKING
V-Max UHMWPE, blue
204* 183176 GLAND, packing, male, throat 1
205 241334 CYLINDER, pump 1
206* 101947 BALL, sst, 0.3750 in.
207* 106556 PACKING, o-ring
208* 193125 V-PACKING, piston
1
1
4
1
1
4
V-Max UHMWPE, blue
209* 108690 SEAL, u-cup
210 240150 VALVE, piston
212† 244199 SEAT, carbide includes 214 and 227
213 194326 HOUSING, intake (foot)
214*† 102972 BALL, sst, 0.875 in.
215 193027 GUIDE, ball
216* 186653 WASHER,
217* 183185 GLAND, female, piston
218* 183174 V-PACKING, leather, piston
219* 183178 GLAND, packing, male
220 240525 SLEEVE,
221* 107098 PACKING,
222 241285 ROD,
223* 183175 V-PACKING, throat
224* 183177 GLAND, packing, female
227*† 108526 PACKING, o-ring
228 193127 SPACER, nut
1
1
1
1
1
1
3
2
1
3
1
1
1
1
1
1
1
*203
201
202
228
224*
223*
204*
222
205
207*
*218
†*214
†*227
* These parts are also included in Repair Kit 240248, which may be purchased separately.
† These parts are also included in Carbide Seat Kit
244199, which may be purchased separately.
221*
220
221*
222
219*
208*
217*
209*
216*
206*
210
215
212†
213
8813A
308798 19
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO.
These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program”.
Graco Phone Number
TO PLACE AN ORDER , contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–690–2894 Toll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit
International Offices: Belgium, Korea, Hong Kong, Japan
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 http://www.graco.com
PRINTED IN U.S.A. 308798 November 1997, Revised 12/2001
20 308798
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project