Graco 307627B AS4000 Electrostatic Spray Gun FLUID SUPPLY HOSE CONVERSION KIT Owner's Manual
Add to My manuals2 Pages
advertisement
INSTRUCTIONS-PARTS LIST
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS
READ AND RETAIN FOR REFERENCE
ORACO
34374~
Rev
SUPERSEDES A
AS4000 Electrostatic SDrav Gun
FLUID SUPPLY HOSE CONVERSION KIT
Required when spraying conductive solvent-based material having a resistivity range of 0.5 megohm t o in- finity, t o maintain the proper electrostatic field.
Kit Part No. 217-496
For AS4000 Guns', Part No. 215-870 and 217-246;
Series A b B Guns Only
I
, flake paint can cause static sparking, which can result in fire or explosion and serious bodily injury or propem damage.
NOTE:
These kits have not been tested by the Cana- dian Standards Association or Factory
Mutual. Installing these kits to certified or approved electrostatic systems voids previous C.S.A. certification and/or F.M. approval.
I
INSTALLATION
WARNING
Installing and servicing this equipment requires access t o parts which may cause electric shock or other serious bodily injury. Do not install or service this equipment unless you are qualified.
Before servicing the tip or gun, and before disassembling the gun, always turn off the High
Voltage Power Supply, shut off the power source t o the pump, and trigger the spray gun t o relieve fluid pressure.
Be sure your insta'llation complies with National,
State and Local codes for the installation of elec- trical apparatus in a Class 1, Group D, Divisions 1 and 2 Hazardous Location.
Disassembling the Gun
Loosen connector (AI from the gun barrel and loosen the fluid tube nut (E). Remove fluid tube (Cl, nut (E) and the collar (E).
Remove the connector (A) from the gun barrel. If your gun has the ferrule (Dl shown
rule. Remove the screw (F), retainer plate (GI and adapter (HI from the bracket
Fig 1
G
'Guns covered in separate instruction manual 307-567.
GRACO INC. P.O. Box MINNEAPOLIS, MN 55440-1444
@COPYRIGHT 1983 GRACO INC.
Assembling t h e Gun
Install the new adapter screw IF) on the bracket (J).
Insert the fluid hose (1) through the adapter enough t o install the collar (3), fluid tube nuts (6 9). fitting (8). retainer (10) and the ferrule (11). These parts must be slipped onto the fluid hose (1). See the Parts
Drawing.
Insert the end of the fluid hose (1) into the gun barrel until it seats against the bottom of the inlet port. See the Parts Drawing. Hold the hose so it is firmly seated and slide the ferrule (11) and retainer (10) into the inlet port. Tighten the retainer (10) until the hex portion of the retainer just contacts the gun barrel.
Screw the fitting (8) into the retainer (10) and tighten until the hex portion of the fitting just contacts the hex portion of the retainer.
I
.-.-
Do not overtighten the fitting (8). Ovenightening will break the fitting. i I
KEY
0
J
K
L
M
2
3
6
Retainer Plata
Tube Bracket
Ground Shield Layer
Outer Jacket
Inner Layer
Fluid Adapter
Collar
Tube Fitting Nut
’
LG
L
CUT-AWAY ViEW
OF FLUID HOSE 111
Fia 2
Screw the nut (9) onto the fitting (8) and tighten.
Insert a screwdriver into the slot in the collar
(6)
(3) and slide it over the ground shield layer (K) of the fluid hose
(1). See Fig 2. Screw the nut and tighten. onto the adapter (2)
PARTS LISTS AND DRAWINGS
Conductive Solvent Conversion K i t 217-496 for
Mid-Range Manual Guns 215-870
A 8 B. e
Series
REF PART
NO. NO.
DESCRIPTION
1 178-831
2 178-826
HOSE, fluid
ADAPTER, fluid
3 179-958 COLLAR
6 106-262
7 179-996
8 180-553
9 107-208
NUT, tube, flareless
CONNECTOR, female
FITTING, male
NUT, ferrule
10 178-130 RETAINER
11 180-550 FERRULE
QTY
Order parts by name and series letter of the assembly for which you are ordering.
SERVICE INFORMATION
I
Listed below by the assembly changed are DELETED and ADDED Darts.
ASSEMBLY PART
CHANGED STATUS
217-496 DELETED
Conversion ADDED
Kit ADDED
REF PART
NO. NO.
~~
NAME
107-207 Fining
8 180553
11 180-5M)
Fitting
Ferrule
I
SERVICE INFORMATION NOTE: Conversion kits
217-497 and 217-498 have been removed from this in- struction manual. Kit 217-497 is now covered in instruc- tion manual 307-683. Kit 217-498 is covered in instruc- tion manual 307-684.
Factory Brnnches:Atlanta, Dallas, Detroit. 10s Angeles. West Caldwell IN.J.1
Subsidiary and Afflibte C o m p n i e e : C a n a d a ; England; Switzarlend: France: Germany; Hong Kong; Japan
GRACO INC. P. 0. Box 1441 MINNEAPOLIS, MN 55440-1444
PRINTED IN U.S.A. a7627 1-E3 R e v i d 2-84
advertisement