INSTRUCTIONS-PARTS LIST

This manual contains important warnings and information.

READ AND KEEP IT FOR REFERENCE.

INSTRUCTIONS

308–594

Rev. A

Auto Gun Manifold Accessory

For use with the H

2

O PRO Continuous Flow System, 237–928 and PRO 5500wb spray guns 237–603 and 238–091

Model 237–965, Series A

with 3-outlet manifold

100 psi (7 bar) Maximum Fluid Working Pressure

WARNING

ELECTRIC SHOCK HAZARD

The Multiple Gun Manifold Kit can only be used with automatic guns.

Regulations applying to this type of equipment prohibit the use of multiple hand-held guns.

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

COPYRIGHT 1995, GRACO INC.

Installation

WARNING

For detailed instructions and warnings, see the Voltage Block manual 308–504 or 308–584 and 308–496.

Installing the Hose Ports and Manifold

1. Take the hose connector off of the fluid regulator outlet (A), and discard it. See Fig. 1, Detail A.

2. Remove the required number of knock-outs from the Voltage Block enclosure (B). See Fig. 2.

Remove one knock-out for each additional hose.

NOTE: To ensure thorough flushing of the manifold, remove additional knock-outs starting from the bottom. For example, a two-hose system would use the top and bottom openings, and a three-hose system would use the top opening and the two bottom openings.

3. Install one fluid hose bulkhead (reference numbers

6 through 10) in each newly-created opening in the

Voltage Block enclosure. Fig. 2 shows the proper order for the parts.

NOTE: Leave the hose ferrule nuts (9) loose until the hoses are installed.

4. Thread a nipple (1) into one of the top openings in the tee (2), and thread the other end of the nipple into the fluid regulator outlet (A). Make sure the tee is installed securely, with the opening facing straight down.

NOTE: Use pipe sealant (5) on all pipe threads.

5. Tightly thread a male connector (3) into the opposite tee opening, and thread a nipple (1) into the tee opening that is facing down.

NOTE: Do not tighten any male connector nuts (E) until the hoses are in place.

6. Tightly thread one male connector into the manifold (4) for each hose you are adding, and tightly thread one plug (11) into each manifold opening that you are not using.

NOTE: As explained in Step 2, use the bottom manifold opening first. Fig. 1 shows how the manifold is oriented.

7. Thread the manifold onto the nipple on the bottom of the tee. Make sure the manifold is installed securely, with the male connectors and plugs facing the fluid hose ports. See Fig. 1.

Connecting the Hoses

WARNING

ELECTRIC SHOCK HAZARD

The Multiple Gun Manifold Kit can only be used with automatic guns.

Regulations applying to this type of equipment prohibit the use of multiple hand-held guns.

1. Push the Graco waterborne fluid supply hoses through the fluid hose bulkheads, and insert the ends fully into the male connectors (3) on the tee (2) and the manifold (4).

NOTE: Be careful not to damage the conductive hose layer (G) when you are pushing the fluid supply hoses through the fluid hose bulkheads.

See Fig. 2.

2. Hand-tighten the hose compression nuts (E) securely onto the male connectors on the tee (2) and manifold (4). Do not overtighten.

NOTE: The hose ferrules (C and D) must be oriented as shown in the Fig. 1, Detail A, with the taper of the solid ferrule (C) facing the tee or manifold, and the taper of the split ferrule (D) facing away from the tee or manifold.

3. Tighten the hose ferrule nuts (9) on the fluid hose bulkheads securely. The hose ferrules ground the conductive layer (G) of the waterborne fluid hoses.

See Fig. 2.

4. Connect the other ends of the fluid hoses to the gun fluid inlets. Read the instructions on fluid hose connection in your automatic gun manual (No.

308–496).

Parts

See DETAIL A

See Fig. 2

A 1 2

DETAIL A

3 C D E

E

4

Fig. 1

6 7 B 8 9

Part No. 237–965, Series A,

Auto Gun Manifold Accessory

Ref.

No.

1

2

8

9

10

11

5

6

3

4

7

Part No.

Description Qty.

113–214 NIPPLE, pipe, PTFE 2

113–216 TEE, pipe, PTFE 1

113–081 MALE CONNECTOR, PTFE

190–753 MANIFOLD, 3-outlet

110–110 SEALANT, pipe (not shown)

154–636 WASHER, 5/8 in, flat.

101–390 WASHER, lock, internal

185–547 FERRULE HOUSING

185–549 FERRULE, hose

185–548 NUT, 5/8–24 3

190–876 PLUG, pipe, 1/4–18 npt (not shown) 2

3

3

1

3

1

4

3

PTFE

F 10 G H

B Voltage Block enclosure

F Inner PTFE hose layer

G Conductive hose layer

H Outer hose jacket

The portion of the inner hose layer (F) that is not covered by the outer hose jacket (H) must be inside of the Voltage Block enclosure (B).

The areas of the waterborne fluid hose that are accessible to personnel during normal operation must be covered by the outer hose jacket (H).

Fig. 2

The Graco Warranty and Disclaimers

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover , and Graco shall not be liable for , any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

THE TERMS OF THIS W ARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER

WARRANTIES (EXPRESS OR IMPLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR

PURPOSE, AND OF ANY NON-CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR STRICT

LIABILITY. EVERY FORM OF LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND

DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR BREACH OF

WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO.

These items sold, but not manufactured by Graco (such as electric motor , switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Graco Phone Numbers

TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you: 1–800–367–4023 Toll Free

FOR TECHNICAL ASSIST ANCE, service repair information, or assistance regarding the application of Graco equipment: 1–800–543–0339 Toll Free

Sales Offices: Atlanta, Chicago, Detroit, Los Angeles

Foreign Offices: Belgium, Canada, England, Korea, Switzerland, France, Germany, Hong Kong, Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

PRINTED IN U.S.A. 308–594 July 1995