- Home
- Do-It-Yourself tools
- Power tools
- Paint Sprayer
- Graco
- 309797A Magnum Interior Texture Sprayers, TexFinish
- Owner's manual
advertisement
Repair
Interior Texture Sprayers
TexFinish™
309797A
For Water-Based Materials Only
Models:
246185
55 psi (3.79 bar) Maximum Fluid Working Pressure
Read warnings and instructions.
Related Manuals
309584
309796 ti3157a
Graco Inc. P.O. Box 1441 Minneapolis, MN
55440-1441 www.graco.com
Copyright 2003
US C
Conforms to ANSI/UL standard 1450
2
WARNINGS
Fire and Explosion Hazard
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in fire or explosion and serious injury.
• The system is for use with water-based materials only. Only use fluids compatible with the equipment. Refer to Technical Data of all equipment manuals. Read fluid and solvent manufacturers warnings.
• Ground the equipment. See Grounding and Electrical Requirements , page 5.
• If there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately. Do not use the equipment until you identify and correct the equipment until you identify and correct the problem.
• Keep work area free of debris, including solvent, rags and gasoline.
• Comply with all applicable state and national fire, electrical and safety regulations.
Equipment Misuse Hazard
Equipment misuse can cause equipment to rupture, malfunction, or start unexpectedly and cause serious injury.
• Before operating this equipment, read all manuals, tags, and labels, including material labels and instructions.
• Do not expose system to rain. Always store system indoors.
• Do not alter or modify equipment.
• Do not spray cementcious materials.
• Do not exceed maximum working pressure of lowest rated component in your system.
• Check equipment daily. Repair or replace worn or damaged parts immediately.
• To reduce risk of serious injury, including electric shock and splashing fluid in eyes, follow Pressure
Relief Procedure
on page 5 before servicing the unit.
• Do not use hoses to pull equipment.
• Route hoses away from traffic areas, sharp edges, moving parts and hot surfaces. Do not expose
Graco hoses to temperatures above 130 F (55 C) or below -35 F (-37 C).
• Air hoses at the compressor end, can get very hot! Allow sprayer to cool down 15 minutes before removing air hose.
• Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.
• Never directly inhale compressed air. Compressed air may contain toxic vapors.
309797A
WARNINGS
Electric Shock Hazard
To reduce the risk of electric shock:
• Be sure sprayer is adequately grounded through electrical outlet, page 5.
• Use only 3-wire, extension cords.
• Make sure ground prongs are intact on sprayer and extension cords.
• Do not operate with cover removed.
• Turn off sprayer. Follow
Pressure Relief Procedure, page 5,
and unplug unit, before removing any parts.
Pressurized Equipment Hazard
Fluid from gun, leaks or ruptured components can splash in the eyes or on skin and cause serious injury.
• Follow when you stop spraying and before cleaning, checking or servicing.
• Do not point spray gun at anyone; put hand, fingers or rag over nozzle, or stop or deflect leaks with your hand, body, glove, or rag.
• Wear protective clothing, gloves, and eyewear.
Cleaning Solvent Hazard with Plastic Parts
Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many solvents can degrade plastic parts to the point where they could fail. Such failure could cause serious
injury or property damage. See Technical Data on page 23 of this instruction manual and in all other
equipment manuals. Read fluid and solvent manufacturer’s warnings.
CAUTION
• Water or material remaining in unit when temperatures are below freezing can damage motor and/or delay pump startup.
To insure water and material are completely drained out of unit:
1. Remove material line from sprayer.
ti3159a 2. Tip sprayer up as shown.
• Before adding material or starting unit in cold weather, run warm water through pump.
Before adding material to hopper, install burp guard. When only a small amount of material remains in the hopper, the burp guard prevents material from shooting out when the unit is turned off. This material could splash in the operator’s eyes or on skin, or into the air.
ti3158a
309797A 3
4
M
Y aa
P
Component Identification
K
N
D
B ti3157a
A
E
W
J
S bb
U
R
Component Identification
L
Item
G
J
E
F
A
B
D
K
L
M
G
Component
Air hose outlet
Material hose outlet
Hopper gun/spray gun selector switch
ON/OFF switch
Air Compressor (inside)
Material/air hose
Texture spray gun (manual 309584)
Material Hopper
Graco RotoFlex™ pump (inside)
Hose rack/cord wrap
F
Item
S
T
U
W
N
P
R
Y aa bb cc
T cc
Component
Touch-up hopper (3/4 gallon)
Nozzle storage
Hose plug
Gun plug
Material thickness gauge
Nozzle (3 sizes available)
Gun air valve
Burp guard
Hopper fitting (fluid inlet)
Hopper clamp
Hose clip
309797A
Preparation
Preparation
Pressure Relief Procedure
To reduce risk of injury, follow this procedure whenever you see this symbol throughout this manual, Also, perform this procedure whenever you:
WARNING
• check or repair any part of this system.
• install or clean spray nozzle.
WARNING
1. Turn Power Switch OFF.
2. Trigger gun into material hopper.
TI2458a page 2
120V AC Systems grounded outlets requires a 120V
AC, 60 Hz, 15A circuit with a grounding receptacle. Do not use an adapter with this product.
grounding prong
Extension Cords
• Use only an extension cord with an undamaged,
3-prong plug.
• For 25 to 50 ft (7.6 to 15.2 m) cords, use 3-wire, 14
AWG (1.5 mm 2 ) minimum.
• For up to 100 ft. (30.48 m) cord, use 3-wire, 12
AWG (2.5 mm 2 ) minimum.
3. Open gun air valve.
ti3160a ti2448a
Grounding and Electrical Requirements
This sprayer must be grounded. Grounding reduces the risk of electrical shock by providing an escape wire for the electrical current. The sprayer cord includes a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Check with a qualified electrician or serviceman if grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. Do not modify plug provided; if it will not fit the outlet, have proper outlet installed by a qualified electrician.
Auxiliary Air Compressor
Do not use an auxiliary air compressor with this spray system.
Generator Requirements
3500 W (3.5 KW) minimum.
Hose Size and Length
The system comes with a hose set consisting of a 3/4 in.
ID x 25 ft (25 mm x 7.6 m) material hose and a 3/8 in-ID air hose.
Do not use more than 25 ft. (7.6 m) of material hose.
WARNING page 2
309797A 5
6
Use RotoFlex Pump Kit 234157.
Disassembly
1.
Relieve Pressure,
2. Unplug sprayer from outlet.
3. Remove shroud
(6 bolts).
RotoFlex™ Pump
6
5
6. Loosen bolt (A) located between air and material hose outlets. Unscrew bolt to lower plate, leaving about 4-5 threads on bolt.
DO NOT REMOVE
BOLT COMPLETELY.
1
2
4 7. Slide a 2 x 4 under motor for support.
ti3162a
3
4. Remove hopper by loosening bottom fitting and then lifting hopper straight up, off unit.
8. Rotate plate.
Slide hose off by pushing outward on hose fitting.
5. Remove material hose.
RotoFlex™ Pump
309797A
Reassembly
Reinstall RotoFlex Pump hose on plate.
1. Kink hose as shown, making sure dots located on hose fitting face each other.
DOTS
2. Slide hose onto plate as shown below, making sure plate slides into slot between hex fitting on end of hose.
RotoFlex™ Pump
3. Align dots located on hose fitting, making sure they are facing each other at all times to ensure the hose does not twist during reinstallation.
ti3127a ti3084a
4. Reposition plate, aligning hex fittings with enclosure openings.
5. Remove 2 x 4 support under motor.
6. Tighten bolt. As bolt is tightened the plate will snug back into place.
7. Replace shroud (6 bolts).
8. Replace hopper.
9. Break in new pump by running dry or with warm water for 3-5 minutes.
ti3125a
309797A 7
8
Compressor Repair
Use Compressor Repair Kit, 234212.
Compressor Repair
7. Tilt compressor forward and remove from housing.
Disassembly
1.
Relieve Pressure
2. Unplug sprayer.
3. Remove shroud (6 bolts).
6
5
TI3011a
4. Remove green ground wire and black, and white wires to compressor.
1
2 ti3022a ti3162a
3
5. Loosen fittings (Aand B) and remove air line.
4
CAUTION
Fan blades are very delicate and can be damaged very easily. When removing or replacing compressor, do not bump or jar shroud or fan blades.
8. Thoroughly clean inside housing, removing dust and debris.
Reassembly
1. Carefully position compressor in housing.
2. Replace bolts using socket wrench to tighten.
Torque to 85 in. lbs.
3. Reattach air lines to compressor. Finger tighten plus one full turn, fittings (A and
B).
ti2748a
A
6. Using a socket wrench with extention, loosen bolts (3).
B ti2749a bolt
4. Reattach 3 wires to compressor matching green to green, black to black and white to white.
bolt ti3032a bolt
5. Replace shroud. Tighten bolts (6).
309797A
Use Roller Repair Kit 234215.
Disassembly
1.
Relieve Pressure
2. Unplug sprayer from outlet
3. Remove shroud (6 bolts).
Roller Replacement
Roller Replacement
Reassembly
CAUTION
When installing bolt through roller, keep nylon washer on shoulder of bolt.
1. Replace rollers.
6
5 ti3030a
1
2
4 ti3162a
3
2. Using a crow bar as a wedge to keep rollers from moving, torque bolts to 40 ft. lbs.
4. Remove RotoFlex Pump, page 6.
5. Using a crow bar as a wedge to keep rollers from moving, loosen shoulder bolt.
6. Remove rollers.
ti3026a ti3031a ti3029a
3. Reinstall RotoFlex Pump hose on plate, page 6.
4. Replace shroud. Tighten bolts (6).
309797A 9
Cylinder
Cylinder
Use Cylinder Repair Kit 246574.
UDisassembly
1.
Relieve Pressure
2. Unplug sprayer from outlet.
3. Remove shroud (6 bolts).
Reassembly
1. Insert swing arm through hole.
ti3086a
1
2
4. Disconnect air hose at quick disconnect fitting.
ti3162a
3
6
5
4
2. Align hole in bottom of cylinder with holes in bottom bracket.
3. Feed pin through.
4. Replace clip.
ti3087a
TI2851A
5. Reattach air hose to quick disconnect fitting.
5. Remove clip.
6. Remove pin.
6. Replace shroud. Tighten bolts (6).
TI2852A ti3085a
7. Pull swing arm out of opening.
10 309797A
Capacitor Replacement
WARNING page 2
Capacitor Replacement
Use Capacitor Replacement Kit 246683.
5. Cut strap.
6. Unplug capacitor and remove.
ti3167a
Disassembly
1.
Relieve Pressure
2. Unplug sprayer.
3. Remove shroud,
(6 bolts).
1
2
4. Capacitors can hold a charge. To prevent electric shock, use a flat bladed screw driver as a conductive device to short out the terminals. To do this, touch the blade of the flat screw driver between two terminal posts on the capacitor. ti3166a ti3162a
3
6
5
4
CAUTION
Do not touch metal part of screw driver when shorting out capacitor.
7. Clean surface to remove dirt and any remaining adhesive.
Reassembly
1. Remove backing from one side of two-sided tape provided in kit and apply to bottom of capacitor.
2. Plug in new capacitor. ti3168a
Wires are not polarized. It does not matter which wires are connected together between capacitor and motor.
3. Remove backing from bottom of two sided tape.
Attach capacitor to plate, pressing taped side firmly into possition. Secure using a wire tie.
4. Replace shroud. Tighten bolts (6).
ti3090a
309797A 11
Motor Repair
Use Motor Repair Kit 246572.
Disassembly
1.
Relieve Pressure
2. Unplug sprayer from outlet.
3. Remove shroud (6 bolts).
Motor Repair
10. Using a flat screw driver, remove c-clip (E).
1
2 ti3162a
4. Remove RotoFlex Pump hose; page 6.
5. Remove Air Cylinder; page 10.
6. Cut wire tie (A).
3
6
5
4
11. Using your hand to support the motor, carefully pull rod (F) out through back.
12. Bring motor to workbench.
13. Remove 4 bolts (G) holding motor to bracket.
F
7. Remove yellow wire (B).
8. Remove ground nut (C).
B
9. Remove blue wire to switch (D).
TI2855A
TI2858A
TI3099a
TI2859A
G
A
14. Cut wire tie. Remove capacitor from plate,
C
D
TI2854A
TI2860A
Reassembly
1. Reposition motor in housing, keeping motor square and aligned to pulley.
2. Keeping tension on belt, tighten 4 bolts (G). Torque to 15 ft-lbs.
The motor will have a tendancy to move when bolts are being tightened. Hold it securely in place, square and aligned to pulley.
3. Secure new capacitor to plate,
ti3090a
TI2856A
12 309797A
4. Using one hand to support motor, slide rod (F) through motor bracket.
5. Replace c-clip (E).
For steps 6-9 refer to illustration below Step 9.
6. Reattach blue wire to switch (D).
7. Replace ground nut (C).
TI2861A ti308
Motor Repair
8. Reattach yellow wire (B).
9. Secure all wires together with wire tie (A), making sure the wires to not touch air line (H) and the motor can swing the full travel (I) without stressing wires.
(C)
(B)
(A)
(H) ti3117a
(D)
10. Reconnect RotoFlex Pump hose, page 6.
11. Replace shroud. Tighten bolts (6).
(H)
309797A 13
Cooler Repair
Cooler Repair
6. Carefully drill out rivets.
Use Cooler Repair Kit 246578.
Disassembly
1.
Relieve Pressure
2. Unplug sprayer.
3. Remove shroud (6 bolts).
4. Loosen nuts (A and B).
1
2 ti3162a
A
3
6
5
4
7. Pull cooler out of housing.
Reassembly
1. Install cooler in housing.
2. Rivet (or use fasteners) in place.
B
5. Disconnect air hose at fitting.
ti3128a ti3097a
3. Reconnect tubing.
Torque nuts (A and B) one full turn beyond hand tight.
4. Replace shroud. Tighten bolts (6).
ti3096a
14 309797A
Relief Valve Replacement
Use Air Releif Valve Kit 246580.
Relief Valve Replacement
Reassembly
1. Reattach air hoses at quick disconnect fitting.
Disassembly
1.
Relieve Pressure
2. Unplug sprayer.
3. Remove shroud (6 bolts).
6
5
TI3098a
1
2
4
2. Slide regulator back into position inside housing.
ti3162a
3
4. Remove screw on top of unit.
5. Remove air lines.
ti3094a ti2736a
6. Pull regulator down through inside of housing.
7. Disconnect air hose at quick disconect fitting.
3. Replace screw on top of unit - torque to 30 in. lbs.
4. Replace shroud. Tighten bolts (6).
TI3093a
309797A 15
Rotor Replacement
Rotor Replacement
Use Rotor Kit 246585 (includes Roller Kit 234215) 7. Remove rotor.
Disassembly
1.
Relieve Pressure
2. Unplug sprayer.
3. Remove shroud (6 bolts).
4. Remove RotoFlex pump
bly, steps 3-5.
2
1
Dissasembly.
6. Using a flat screwdriver, remove c-clip (A).
ti3162a
3
6
5
4
Reassembly
1. Install rotor with flange facing outward.
TI2868A
2. Replace c-clip (A).
3. Install rollers, page 9, Reassembly.
4. Reconnect RotoFlex Pump hose, page 9, Reassem-
bly steps 3-4.
5. Replace shroud. Tighten bolts (6).
A
TI3099a
16 309797A
Troubleshooting
Troubleshooting
Problem Cause Solution
Sprayer won’t run
Pump won’t pump material
Power switch not on
No power at wall outlet
Wrong size generator
Too many items on same circuit
Extension cord too long or wrong gauge
Breaker tripped
Selector switch in wrong position
Air lock
Mix too thick
Turn switch on.
Check outlet by plugging in another appliance. If appliance does not work, try another outlet.
Use a 3500 watt or larger generator.
Refer to Generator Requirements,
Unplug other items from circuit
Use a different extension cord. Refer to Grounding and Electric Requirements, page 5
Reset breaker
Move selector switch to correct position for application
Open air valve on gun
Add water to thin material. Use Material Thickness Gauge.
Loose fittings
Plugged gun
Check and retighten all fittings
Relieve Pressure,
gun from hose. Clean gun.
RotoFlex pump worn out Replace hose. Recommended hose replacement - once a year or every
3000 gallons.
Pump cold or material frozen in pump Move pump to warm room and allow it to warm up or run hot water through sprayer.
Motor start capacitor failure
Material runs out of bottom of sprayer RotoFlex pump worn out
No air from compressor
Loose fittings
Gun air valve closed
Low voltage
Gun needle plugged
Lines not connected
Replace capacitor and restart
Replace hose
Check and retighten all fittings
Open gun air valve
Check extension cord length and gauge. Replace if different than recommended. Refer to Grounding and
Electrical Requirements, page 5.
Clean needle and retry.
Damaged hose
Worn compressor
Check all quick disconnect connections to gun and hoses
Replace hose
Replace compressor. Contact a qualified Graco Service Center.
309797A 17
Troubleshooting
Problem Cause Solution
Speed of application too slow
Intermittent flow/sputtering
Quick disconnect does not stay connected.
Gun will not shut off
Fluid leaking out of either plug
Material too thick
Nozzle too small
Too much air being used.
Plugged or dirty gun
Kinked hose Unkink hose.
Gun fluid flow adjustment set too low Increase flow adjustment with flow adjustment nut.
RotoFlex pump worn
Hopper connection not tight
Debris in system
Dirty or corroded fitting
Partially close gun air valve to reduce air flow.
Relieve Pressure
gun.
Replace hose.
Check gasket. TIghten connection.
Clean
Clean thoroughly. Soak in oil. Apply a few drops of light oil.
Worn nozzle or needle.
Thin material.
Change nozzles to a larger size. See
Operation Manual, Recommended
Nozzle Selection Chart, page 10.
Debris in needle passage
Fluid leaking at Flow Adjustment Nut Damaged seal.
Missing or damaged o-rings
Relieve Pressure
worn parts.
Relieve Pressure
Relieve Pressure
seal.
Relieve Pressure
o-rings.
Needle adjustment won’t adjust
Gun damaged
Dirty threads
Nozzle not on gun
Replace gun
Clean threads
Put nozzle on gun
18 309797A
Wiring Diagram
ELECTROLYTIC CAPACITOR
BLACK
BLACK
MOTOR
POWER
SWITCH
BLUE
SELECTOR
SWITCH
GREEN
GROUND
YELLOW
WHITE
BLACK
GREEN
BLACK
GREEN
POWER
CORD
AIR COMPRESSOR
WHITE
BLACK ti3120a
Air Diagram
AIR MAIFOLD
Wiring Diagram
309797A
AIR CYLINDER
AIR COMPRESSOR
AIR COOLER
TI3179a
19
20
Parts ti2690a
Parts
Model 246185
39
39a
39b
22
6
11 11
27
59
20
52(A)
57(B)
10
9
4
3
23
79
20
21
76
63
21
38
67
36
34
60
309797A
Parts
Model 246185
14
15
44
45
55
29
12
8
17
79
44
75
66
33
77
30
51
58
37
1
41
25
16
56
74
48
19
32
33
35
54
24
(B)57
18
46
(A)50
56
13
49
20
47
31
20
5
26
28 ti2691a
Parts
309797A 21
Parts
14
15
16
17
18
10
11
12
13
8
9
5
6
3
4
1
2
31
32
33
34
27
28
29
30
23
24
25
26
19
20
21
22
35
36
37
Ref
No.
Part No. Description Qty
234215 KIT, roller
BEARING, ball
117563 SWITCH, selector
117693 SWITCH, on/off
15B858 LEG, frame
15A903 PLATE, hose
246585 KIT, pulley, includes 1, 2, 41
15C087 PLATE, frame, top
15B873 SUPPORT, front, frame
246580 KIT, manifold, air, includes 19
15B439 SHAFT, pivot, motor tray
15B530 ROD, axle
15B861 HANDLE, 1
15B543 RACK, hose 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
15B857 FRAME, bottom
246189 TRAY, motor
246574 KIT, cylinder, air, includes 24, 46,
47
117625 NUT, locking
117630 SCREW, torx, tri-lob
117633 SCREW, slot, hex wash hd
117636 SCREW, hex hd, flanged
234157 KIT, RotoFlex pump
15B529 ARM, cylinder
246572 KIT, motor, AC, includes 41, 66, 79 1
112612 CAP, hub
1
1
6
1
1
8
113415 SCREW, mach, torx pan hd
115095 WHEEL, 9”
115480 KNOB, t-handle
116630 SCREW, carriage
195367 SPACER
15B585 HARNESS, wiring
117727 CLIP, wire
15B865 SHIELD
234212 KIT, compressor, air, includes 54
234148 KIT, hose
15B507 CORD set, power
1
3
2
2
2
2
2
1
1
1
1
1
Parts
Model 246185
Ref
No.
Part No. Description
67
74
75
76
77
78
60
62
63
66
56
57
58
59
51
52
54
55
47
48
49
50
41
44
45
46
38
39
39a
39b
79
246544 GUN, texture, manual 309584
246316 HOPPER, 6-gallon
STORAGE, nozzle
GUARD, burp
117672 BELT, GT2, 3mm
101134 RING, retaining, ext.
101242 RING, retaining, ext
117671 PIN, clevis
117668 PIN, cotter, bow tie
115498 SCREW, mch, hx wash hd
15B783 SHIELD, spray
246578 KIT, cooler, air, includes 51, 54, 56
113084 RIVET, blind
15B823 TUBE, air
15B818 TUBE, air
115651 NUT, hex, acorn, 5/16-18
117728 FITTING, compression, union
15B822 TUBE, air
198492 LABEL, warning
290228 LABEL, caution
15B889 LABEL
103473 STRAP, tie, wire
276906 HOPPER, texture, .75 gal
117791 SCREW, cap, tri-lobe
15B986 CLIP, spring
186620 LABEL, symbol, ground
15C127 LABEL, instruction
15C128 LABEL, danger
291292 LABEL, identification
234220 KIT, material thickness gauge, (not shown)
246683 KIT, capacitor
Qty
1
1
1
1
1
1
1
4
1
2
1
1
2
1
1
1
2
1
1
1
1
1
2
1
1
2
1
1
1
1
1
Replacement Danger and Warning labels, tags and cards are available at no cost.
22 309797A
Main unit power requirements
Maximum fluid working pressure
Maximum air working pressure
Compressor specifications
Compressor air displacement
Generator required
Electric Motor
Material motor
Compressor motor
Power Cord
Material hopper capacity
Pump motor
Maximum delivery with texture
Dimensions: 750
Length
Width
Height
Weight
Without hoses or gun
Wetted parts
Sound data
Sound pressure level*
Sound power level**
Storage Temperature Range
Operating Temperature Range
Gun:
Maximum Working Pressure
Air Maximum Working Pressure
CFM Rating
Weight
*Measured while spraying at 1 m.
**Measured per ISO-3744
Technical Data
120V AC, 60 hz, 15A, 1 phase
60 psi, (4.137 bar)
45 psi (3.10 bar)
Universal motor thermally protected, oil-less
4.5 displacement scfm at 30 psi
3500 w minimum
Capacitor start AC 2.8 amp
Universal AC 10.5 amp
16 AWG, 3 wire, 25 ft.
6 gallons
Gun material hopper: 3/4 gallon
.75 hp AC, open frame
1 to 1.5 gpm (3.8 to 5.7 lpm)
23 in. (584 mm) with handle
24 in. (610 mm)
40 in. (1016 mm)
77 lbs (34 kg) brass, aluminum, plastic
79 dB(A)
87.5 dB(A)
-30°F - 160°F (-35°C - 71°C)
40°F - 115°F (4°C - 46°C)
60 psi (4.137 bar)
100 psi (6.895 bar)
3.5 - 11 CFM, 15-100 psi
35 oz (1600 grams)
Technical Data
309797A 23
Limited Warranty
Limited Warranty
Graco warrants to the original purchased (other than for purposes of resale or rental) all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship if operated in accordance with Graco’s printed recommendations and instructions. This warranty applies for one year from the date of purchase.
This warranty does not cover and Graco shall not be liable for general wear and tear, or any malfunction, damage, or wear caused by improper use, accidents, user negligence, use of non-Graco component parts or service or repair performed by anyone other than a Graco authorized service center.
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE.
GRACO SHALL NOT IN ANY EVENT BE LIABLE FOR INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE OR EXPENSE OF
ANY KIND, WHETHER FROM BREACH OF THIS WARRANTY OR ANY OTHER REASON. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
To make a claim under this warranty, return the product with proof of purchase, transportation prepaid, to any Authorized Graco Service Center.
Graco’s Authorized Service Center, at its option, will either repair or replace the product and return it to you, postage, prepaid. To find the nearest
Graco Authorized Service Center call 1-888-541-9788 or visit our website at www.Graco.com
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit
International Offices: Belgium, Korea, Hong Kong, Japan
PRINTED IN USA 309797 1/2003
24 309797A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project