Hlihome DKMS-7022-12ORB 1-Spray Patterns installation Guide
Add to My manuals11 Pages
Hlihome DKMS-7022-12ORB is a modern shower faucet set that combines style, functionality, and durability. It features a sleek design with a brushed gold finish that will complement any bathroom décor. The faucet is constructed from solid brass for long-lasting performance and includes a variety of features that make it easy to use and maintain.
advertisement
Customer Service : 323-982-8955
Email : [email protected]
Website:www.boyelliving.com
SHOWER FAUCET
Installation Manual
1
、
Installation Precautions
1.
When you open the product packaging, please check the product and accessories at first. If there is any discrepancy, please contact the company or our distributor immediately.
2.
The hot and cold water supply pipe of the faucet must be properly connected.
When facing the front of the faucet, the hot water supply is on the left and cold water supply is on the right. Incorrect connection will cause permanent damage to the cartridge.
3.
If the accessories to be changed without affecting the use, we will not make a prior notice.
4.
The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5.
The water pressure of the faucet is 0.05MPa-1.0MPa (including cold water and hot water pressure).
Applicable water temperature range: 39 ℉ - 194 ℉
2 、
Preparation before installation
1 .
Please read the installation manual carefully before installation.
2 .
Installation work must be performed by a professional installer.
3 .
Installation tool :
1
5.3"
4 、
Technical drawing of drilling size
1 、 The size of the embedded box that needs to be drilled
is 5.3"*6.7".
5.3"
Top shower outlet water
Hot water
2 、 The depth of the embedded box is 1.8"-2.2".
It's better to drill the depth of 1.8"for blank wall.
2.2"
Handle shower outlet water wall cold water
Tile surface
3
5.3"
5 、
Pipe connection
1 、 Please drill the holes on the wall for the main body embedded part, hot and cold water inlet pipes as well as shower arm connection pipes according to the basic product dimension drawing as below.
2 、 Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve,and tighten with the wrench
4
6 、
Water testing and sealing testing
1 、 After the pipe connection is completed, open the protective panel
and cover, and then open the cartridge, flush the pipeline;
then close the cartridge to check the pressure resistance and sealing
performance of the pipeline, make sure there are no leakage.
2 、 Block each outlet pipe with a stopper then open the cartridge to
check if the pipe joint is well-sealed and the pipe condition under
pressure to ensure no leakage.
Testing Purpose: Flush the impurities and sludge in the pipeline
to avoid clogging and affect the effluent functions.
5
7 、
The procedure of sealing the wall
Use a parallel ruler to measure the flatness of the embedded box
casing and the vertical wall surface. If the wall surface is not flat,
it should be patched to ensure the embedded box casing and vertical
wall angle meets at nearly ideal angle of 90, then lay the tile decoration.
wall
Tile surface
Protective cover is roughly even with tile
6
8 、
Installation of control valve
1 、
Take off the protective panel and cover
2 、 The decorative panel and the handle are connected to
the control valve as shown below sequence.
According to the figure below, please correctly adjust the direction of water separator handle
Top shower outlet water
Handle shower outlet water
7
9 、
Shower sets installation
8
10
、
Handle shower installation
9
1 1 、
Product reparation
If the cartridge is worn out which cause leakage, please turn
off the water source. Remove the handle, panel, and decorative
cover in sequence, remove the gland with a wrench, then take
out the cartridge and copper sleeve.
Repair or replace the new cartridge, then install it again in sequence.
1 2 、
Clearance and Maintenance
In order to keep the faucet appearance smooth and good
performance, please follow the below steps to clean and
maintain the faucet.
1 、 Clean with water and dry with a soft cotton cloth ;
2 、 Use a mild liquid and a colorless glass cleaner to remove surface
dirt and scale, also you can use the cleaner without grinding function.
3 、 Do not use detergents, polishing tools, abrasive cloth, paper towels
or scrapers to clean the faucet.
4 、 Do not use acid cleaners, insoluble granular detergents, soaps, etc
to clean the faucet.
1 0
advertisement
Key Features
- Solid brass construction for durability
- Brushed gold finish for a stylish look
- Single-handle design for easy control
- Ceramic disc cartridge for smooth operation
- Includes a hand shower for added convenience
- Easy to install and maintain