advertisement
SCAN HERE FOR HELP
CONTACT US [email protected]
Installation Manual
ENJOY BATH , ENJOY LIFE
CONTENTS
1
Brand Introduction
2
Certification for
North American
3
Installation Manual
01
02
03
13.
PRODUCT REPARATION
If the cartridge is worn out which cause leakage, please turn off the water source. Remove the handle, panel, and decorative cover in sequence, remove the gland with a wrench, then take out the cartridge and copper sleeve.
Repair or replace the new cartridge, then install it again in sequence.
14. CLEARANCE AND MAINTENANCE
In order to keep the faucet appearance smooth and good performance, please follow the below steps to clean and maintain the faucet.
1 、 Clean with water and dry with a soft cotton cloth
;
2 、 Use a mild liquid and a colorless glass cleaner to remove surface
dirt and scale, also you can use the cleaner without grinding function.
3 、 Do not use detergents, polishing tools, abrasive cloth, paper towels
or scrapers to clean the faucet.
4 、 Do not use acid cleaners, insoluble granular detergents, soaps, etc
to clean the faucet.
Collections
Inspirations in the bathroom and kitchen from ESNBIA
An ESNBIA collection consists of bathroom sink faucets and showers, bathtubs faucet and accessories – all of consistent design. Here, ESNBIA’s design partners lend the collections their own particular character.
13
11. HANDLE SHOWER INSTALLATION
7
12.
ADJUSTMENT OF CHECK VALVES
The outlet water adjusting device of the left and right sides, it can adjust the water flow rate and colse outlet water function when you need to repair/change cartridge.
It can close water when you screw clockwisely slotted screwdriver on both sides
Note:If only colse one side that it will cause faucet abnormal outlet water,for normal outlet water please make sure the adjusting position on both sides is open(counterclockwise to open).
12
BRAND INTRODUCTION
“I am sure there are things that can’t be cured by a good bath, but I can’t think of one,” wrote by novelist Sylvia Plath in The Bell Jar.
We’ve long known that going for a run, or getting any form of exercise, helps get you out of a bad mood and enter the happy zone!
But there’s one more thing you should de�initely do to help symptoms of SAD, lethargy and feeling crappy in general…
When you have had a very long day, when fate seemed to have something against you, throwing all sorts of challenges and negative energy bombs your way, trying to see if you can actually trip and fall, a bath will save the day.
When you have a sore back from all those hours sitting stif�ly in front of the computer, when you simply need to get away from everything and enjoy a few moments with yourself or relax without having to leave your house, a bath is the solution you’ve been looking for.
A bath can make your life better!
Enjoy bath, enjoy life
01
ESNBIA Search
10.
SHOWER SETS INSTALLATION
FOR CEILING MOUNTED
SHOWER ARM http://pld.iapmo.org/default.aspx
Attention: Be aware of the faucets you are buying. Only those full set faucets listed in IAPMO R&T are qualified with UPC certificate - Not partial components, such as cartridge, gadgets or other parts of the faucets could be claimed with
UPC certified.
let’s make it simple,
UPC models=all the water passing parts are UPC certified
One part with UPC≠one complete model with UPC
So how to verify one model with or without UPC,please
check below.
Entering the IAPMO R&T website online!
STEP1
Select the "Listee Name", and enter the company name “HIMARK” in the search box, then the below will display the company name"HIMARK sanitary ware co., ltd" and the corresponding certificate number.
02
STEP2
STEP3
Click UPC Certificate No. 8933, and you will see a list of products that have received the UPC certificate. All product models in the list are received the UPC certificate.
On the page of product list, you can use the "Ctrl + F" key on the computer keyboard, and enter the product model you want to find in the search box, the system will automatically match the product model that you want.
11
9. INSTALLATION OF CONTROL VALVE
1 、 Take off the protective panel and cover
2 、 The decorative panel and the handle are connected to
the control valve as shown below sequence.
10
According to the figure below, please correctly adjust the direction of water separator handle
Top shower outlet water
Handle shower outlet water
1.
INSTALLATION PRECAUTIONS
1.
2.
When you open the product packaging, please check the product and accessories at first. If there is any discrepancy, please contact the company or our distributor immediately.
The hot and cold water supply pipe of the faucet must be properly connected.
When facing the front of the faucet, the hot water supply is on the left and cold water supply is on the right. Incorrect connection will cause permanent damage to the cartridge.
3.
If the accessories to be changed without affecting the use, we will not make a prior notice.
4.
The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5.
The water pressure of the faucet is 0.05MPa-1.0MPa (including cold water and hot water pressure).
Applicable water temperature range: 39 ℉ - 194 ℉
2. PREPARATION BEFORE INSTALLATION
1 .
Please read the installation manual carefully before installation.
2 .
Installation work must be performed by a professional installer.
3 .
Installation tool :
03
3. TWO FUNCTION CONCEALED FAUCET
ACCESSORIES LIST
10
9
12 11
8
5
1
2
3
4
6
7
Number
1
2
3
9
10
7
8
11
12
4
5
6
Description
Pressure balanced valve
Cover board
Diverter handle
Cartridge handle
Elbow with hook
Shower hose
Handle shower
Shower head
Shower arm
Cover board
Nails bag
Allen-key
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
04
8. THE PROCEDURE OF SEALING THE WALL
Use a parallel ruler to measure the flatness of the embedded box casing and the vertical wall surface. If the wall surface is not flat, it should be patched to ensure the embedded box casing and vertical wall angle meets at nearly ideal angle of 90, then lay the tile decoration.
2.2"-2.6"
≤ 3.2" wall Tiles
09
7. WATER TESTING AND SEALING TESTING
1 、 After the pipe connection is completed, open the protective panel
and cover, and then open the cartridge, flush the pipeline;
then close the cartridge to check the pressure resistance and sealing
performance of the pipeline, make sure there are no leakage.
2 、 Block each outlet pipe with a stopper then open the cartridge to
check if the pipe joint is well-sealed and the pipe condition under
pressure to ensure no leakage.
Testing Purpose: Flush the impurities and sludge in the pipeline
to avoid clogging and affect the effluent functions.
Top shower outlet water
Hot water
Cold water
Handle shower outlet water
Top shower outlet water
Hot water
Handle shower outlet water
Cold water
08
4. TECHNICAL DRAWING OF PRODUCT
Unit: inch
1/2 -14NPT
5.1"
1/2-14NPT
4-1/2-
14NPT
05
5. TECHNICAL DRAWING OF DRILLING SIZE
1 、 The size of the embedded box that needs to be drilled
is 4.7"*6.7".
4.7"
1.8"
2 、 The depth of the embedded box is 2.2"-2.6".
It's better to drill the depth of 2.2"for blank wall.
2.2"-2.6"
≤ 3.2" wall Tiles
Top shower outlet water
Hot water inlet
Handle shower outlet water
Cold water inlet
Hot water
Top shower outlet water
Cold water
Handle shower outlet water
06
6.
PIPE CONNECTION
1 、 Please drill the holes on the wall for the main body embedded part, hot and cold water inlet pipes as well as shower arm connection pipes according to the basic product dimension drawing as below.
2 、 Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve,and tighten with the wrench
07
advertisement