Blauberg Tower-H User Manual
BLAUBERG Tower-V is a centrifugal roof fan that's perfect for industrial ventilation, swimming pools, offices, restaurants, and more. It's designed for vertical exhaust ventilation and can handle air with no dust, impurities, sticky substances, or fibers. With its powerful motor and efficient design, it'll keep your air fresh and clean.
Reklam
Reklam
Centrifugal roof fan
TOWER-V
TOWER-H
EN
USER'S MANUAL
www.blaubergventilatoren.de
CONTENTS toWer-V/toWer-H
This user’s manual is a main operating document intended for technical, maintenance, and operating staff.
The manual contains information about purpose, technical details, operating principle, design, and installation of the TOWER-V/TOWER-H unit and all its modifications.
Technical and maintenance staff must have theoretical and practical training in the field of ventilation systems and should be able to work in accordance with workplace safety rules as well as construction norms and standards applicable in the territory of the country.
SAFETY REQUIREMENTS
All user’s manual requirements as well as the provisions of all the applicable local and national construction, electrical, and technical norms and standards must be observed when installing and operating the unit.
Disconnect the unit from the power supply prior to any connection, servicing, maintenance, and repair operations.
Only qualified electricians with a work permit for electrical units up to 1000 V are allowed for installation. The present user’s manual should be carefully read before beginning works.
Check the unit for any visible damage of the impeller, the casing, and the grille before starting installation. The casing internals must be free of any foreign objects that can damage the impeller blades.
While mounting the unit, avoid compression of the casing! Deformation of the casing may result in motor jam and excessive noise.
Misuse of the unit and any unauthorised modifications are not allowed.
Transported air must not contain any dust or other solid impurities, sticky substances, or fibrous materials.
Do not use the unit in a hazardous or explosive environment containing spirits, gasoline, insecticides, etc.
Do not close or block the intake or extract vents in order to ensure the efficient air flow.
Do not sit on the unit and do not put objects on it.
The information in this user’s manual was correct at the time of the document’s preparation.
2
toWer-V/toWer-H www.blaubergventilatoren.de
The Company reserves the right to modify the technical characteristics, design, or configuration of its products at any time in order to incorporate the latest technological developments.
Never touch the unit with wet or damp hands.
Never touch the unit when barefoot.
This unit is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the unit by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the unit.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
Cleaning and user maintenance shall not be made by children without supervision
Children shall not play with the appliance.
Connection to the mains must be made through a disconnecting device, which is integrated into the fixed wiring system in accordance with the wiring rules for design of electrical units, and has a contact separation in all poles that allows for full disconnection under overvoltage category III conditions.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a safety hazard.
Ensure that the unit is switched off from the supply mains before removing the guard.
WARNING: If there are any unusual oscillating movements, immediately stop using the unit and contact the manufacturer, its service agent or suitably qualified persons.
The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.
Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances.
The manufacturer, designer, installer and operator are responsible for the correct operation and functioning of the unit.
THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS
SERVICE LIFE.
DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE
3
www.blaubergventilatoren.de
PURPOSE toWer-V/toWer-H
THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED
PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT THE APPROPRIATE
TRAINING.
THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED
PERSONNEL AFTER THE APPROPRIATE BRIEFING.
THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORISED
ACCESS BY UNATTENDED CHILDREN.
The TOWER-V/TOWER-H roof fans in metal casing are designed for ventilation systems in industrial premises as well as pools, apartment buildings, offices, hospitals, restaurants and other premises heated during the winter season.
The fan is mounted on the exhaust shaft of the air duct and is used only for exhaust ventilation.
DELIVERY SET
NAME
Fan
User’s manual
Packing box
DESIGNATION KEY
NUMBER
1 pc.
1 pc.
1 pc.
Designation example: TOWER-V 310 2 E S
Centrifugal roof fan
TOWER-V — with vertical air discharge
TOWER-H — with horizontal air discharge
Turbine standard size [mm]
Number of motor poles
2, 4, 6
Number of phases
E — single-phase
D — three-phase
Options
S — built-in external switch
4
toWer-V/toWer-H
TECHNICAL DATA
The unit is rated as a Class I electrical appliance.
TOWER-V
M d
C
B
A
L
D*
∅ D* – flange connection dimensions.
TOWER-H www.blaubergventilatoren.de
d
M
D*
A
5
www.blaubergventilatoren.de
toWer-V/toWer-H
Model
TOWER-V 190 2E
TOWER-V 220 2E
TOWER-V 225 2E
TOWER-V 225 4E
TOWER-V 250 2E
TOWER-V 250 4E
TOWER-V 280 4E
TOWER-V 310 2E
TOWER-V 310 4E
TOWER-V 310 4D
TOWER-V 355 4E
TOWER-V 355 4D
TOWER-V 400 4E
TOWER-V 400 6E
TOWER-V 400 4D
TOWER-V 450 4E
TOWER-V 450 6E
TOWER-V 450 4D
TOWER-V 500 6E
TOWER-V 500 4D
TOWER-V 500 6D
TOWER-V 560 6E
TOWER-V 560 4D
TOWER-V 560 6D
TOWER-V 630 6D
TOWER-V 710 6D
H [mm]
300
300
330
330
375
375
375
430
170
190
215
215
240
240
276
276
430
425
460
460
460
485
485
485
485
485
A [mm]
613
613
738
738
738
738
738
738
417
417
417
417
481
481
547
547
738
738
859
859
859
859
859
859
951
992
477
477
598
598
598
598
598
668
355
355
355
355
425
425
425
425
668
668
668
668
668
833
833
833
939
980
330
750
450
450
450
450
450
535
245
245
245
245
330
330
330
330
535
535
535
535
535
750
750
750
750
840
Overall and connecting dimensions [mm]
B [mm] C [mm] D [mm] d [mm]
11
11
11
11
11
11
11
11
(4 holes)
9
9
9
9
11
11
11
11
11
11
11
11
11
11
11
11
20
20
285
285
438
438
438
438
438
438
213
213
210
210
285
285
291
285
438
438
445
430
445
605
605
605
600
674
M [mm]
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M6
M6
M6
M8
(6 places)
M6
M6
M6
M6
M6
M6
M6
Weight
[kg]
33
31
33
41
20
19
26
26
9
9
13
13
7
7
7
7
52
63
63
63
41
41
52
52
81
114
L [mm]
670
670
790
790
790
790
790
790
480
480
480
480
540
540
600
600
790
790
910
910
910
910
910
910
1000
1040
Model
TOWER-H 190 2E
TOWER-H 220 2E
TOWER-H 225 2E
TOWER-H 225 4E
TOWER-H 250 2E
TOWER-H 250 4E
TOWER-H 280 4E
TOWER-H 310 2E
TOWER-H 310 4E
TOWER-H 310 4D
TOWER-H 355 4E
TOWER-H 355 4D
TOWER-H 400 4E
TOWER-H 400 6E
TOWER-H 400 4D
TOWER-H 450 4E
TOWER-H 450 6E
TOWER-H 450 4D
TOWER-H 500 6E
TOWER-H 500 4D
TOWER-H 500 6D
TOWER-H 560 6E
TOWER-H 560 4D
TOWER-H 560 6D
TOWER-H 630 6D
TOWER-H 710 6D
H [mm]
287
287
322
347
376
376
376
420
189
180
210
233
237
237
265
251
420
420
461
490
461
489
489
489
520
570
H1 [mm]
294
294
361
386
415
415
415
459
195
186
217
240
244
244
272
258
459
459
501
530
501
528
528
528
560
619
B [mm]
450
450
620
620
620
620
620
700
350
338
350
350
450
450
450
450
700
700
700
700
700
895
895
895
990
1050
Overall and connecting dimensions [mm]
A [mm]
451
451
625
625
625
625
625
710
351
337
351
351
451
451
451
451
710
710
710
710
710
900
900
900
1000
1060
C [mm]
330
330
450
450
450
450
450
535
245
245
245
245
330
330
330
330
535
535
535
535
535
750
750
750
750
840
D [mm]
285
285
438
438
438
438
438
438
213
213
210
210
285
285
291
291
438
438
445
430
445
605
605
605
600
674 d [mm]
11
11
11
11
11
11
11
11
11
20
20
11
11
11
11
11
11
11
11
(4 holes)
11
11
11
11
11
11
11
Weight
[kg]
14.2
14.2
28.3
30.3
35
32.7
35
46.6
8.2
7
9.2
8.8
12.7
12.1
13.5
13.2
45.6
45.5
52.8
46.6
52.7
76.4
81.4
76.4
96.3
134
M [mm]
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
(6 places)
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
6
toWer-V/toWer-H www.blaubergventilatoren.de
Voltage [V]
Frequency [Hz] 50
Power [W]
190 2E
1~ 230
69
60
220 2E
50
1~ 230
60
TOWER-V / TOWER-H
225 2E
1~ 230
50 60
89 108 118 123 169
225 4E
1~ 230
50
49
Current [A] 0.30
0.40
0.49
0.54
0.54
0.70
Max. air flow [m³/h] 610 654 880 883 915 1010
RPM [min -1 ] 2680 2980 2580 2840 2790 2820
Sound pressure level at 3 m distance [dBA]
Transported air temperature [°C]
48 49 50 51 51 52
-25...+50
SEC class* C
Ingress protection rating
C C -
IPX4
0.22
738
1400
45
B -
250 2E
1~ 230
50 60
184 232
0.81
0.90
1450 1320
2480 2320
54 53
-
Voltage [V]
Frequency [Hz] 50
280 4E
1~ 230
60
310 2E
1~ 230
50 50
TOWER-V / TOWER-H
310 4E
1~ 230
60
310 4D
50
3~ 400
60 50
355 4E
1~ 230
60 50
355 4D
3~ 400
60
Power [W] 125 155 324 141 195 155 202 219 304 264 330
Current [A] 0.61
0.99
1.42
0.64
0.87
0.29
0.32
0.96
1.33
0.58
0.64
Max. air flow [m³/h] 1490 1520 2150 2265 2425 2300 2442 2480 2976 3290 3540
RPM [min -1 ] 1446 1710 2620 1420 1740 1410 1550 1420 1580 1430 1650
Sound pressure level at 3 m distance [dBA]
Transported air temperature [°C]
46 46 58 47 49
-25...+50
47 48 51 52 52 53
-30...+60
Ingress protection rating IPX4
Voltage [V]
Frequency [Hz]
Power [W]
Current [A]
Max. air flow [m³/h]
RPM [min -1
Sound pressure level at 3 m distance [dBA]
Transported air temperature [°C]
Ingress protection rating
]
400 4E
1~ 230
50
457
2.00
3950
1440
55
50
184
0.89
2740
945
47
400 6E
1~ 230
60
249
TOWER-V / TOWER-H
400 4D
3~400
1.10
3289
1071
49
-30...+60
50
420
0.99
3950
1440
55
450 4E 450 6E 450 4D
1~ 230 1~ 230 3~400
50
749
3.35
6180
1400
58
50
268
1.25
4380
940
50
50
755
1.50
5920
1440
57
500 4D
3~400
-30...+50
50
1527
2.64
8435
1460
62
IPX4
500 6E
Voltage [V]
Frequency [Hz] 50
1~230
60
500 6D
50
3~400
60
Power [W] 407 673 440 599
Current [A] 1.81
3.05
1.23
1.32
Max. air flow [m³/h] 5680 6532 6000 6122 13560
RPM [min -1 ] 970 1120 978 1125 1400
Sound pressure level at 3 m distance [dBA]
Transported air temperature [°C]
52 54 52
-25...+60
54 66
Ingress protection rating
1970
3.36
TOWER-V / TOWER-H
560 4D 560 6E 560 6D 630 6D 710 6D
3~400
50
1~230
50
3~400
50
3~400
50
3~400
50
613
2.70
9560
930
58
-25...+50
696
1.44
9630
970
58
IPX4
1110
2.42
12640
957
64
2583
4.87
17010
945
67
-25...+70
250 4E
1~ 230
50
48
0.23
820
1440
46
B
7
www.blaubergventilatoren.de
toWer-V/toWer-H
MOUNTING AND SET-UP
BEFORE MOUNTING MAKE SURE THE CASING DOES NOT CONTAIN ANY FOREIGN
OBJECTS (E.G. FOIL, PAPER).
WHILE INSTALLING THE UNIT ENSURE CONVENIENT ACCESS FOR SUBSEQUENT
MAINTENANCE AND REPAIR.
• Fans are designed for horizontal mounting on a flat roof directly above an air duct or a ventilation shaft.
• In order to avoid ingress of water and snow into the ventilation duct, it is possible to install a fan on the mounting frame.
• The fan is connected to the ventilation duct by means of a counter flange, which is attached directly to the fan base.
• The fan base has holes for fixing bolts that attach the fan to a stationary even surface or to a mounting frame.
• In the models TOWER-V 220 2E, TOWER-V 225 2E, TOWER-V 225 4E, TOWER-V 310 4E, TOWER-V 310 4D, TOWER-V/TOWER-H 500 6E,
TOWER-V/TOWER-H 500 4D, TOWER-V/TOWER-H 500 6D, TOWER-V/TOWER-H 630 6D, TOWER-V/TOWER-H 710 6D the counter flange is attached together with the fan inlet ring.
• A mounting frame, a counter flange and mounting bolts are not included in the delivery set and must be purchased separately.
TOWER-V
TOWER-H
OPERATION OF FANS WITHOUT A CONNECTED AIR DUCT SYSTEM IS IMPROPER
8
toWer-V/toWer-H
INSTALLATION CHART
Roof fan base
Insulation
Roof design
FDL counter flange
KDL backdraft damper
INSTALLATION EXAMPLES
VDL flexible insert
Air duct www.blaubergventilatoren.de
1 1
6
2
4
5
3
2
4
6
5
3
6
4
5
1 – roof fan; 2 – VDL flexible insert; 3 – KDL backdraft damper; 4 – FDL counter flange; 5 – MRDL or MRIDL mounting frame; 6 – air duct.
9
www.blaubergventilatoren.de
CONNECTION TO POWER MAINS toWer-V/toWer-H
DISCONNECT THE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT.
CONNECTION OF THE UNIT TO POWER MAINS IS ALLOWED BY A QUALIFIED
ELECTRICIAN WITH A WORK PERMIT FOR THE ELECTRIC UNITS UP TO 1000 V AFTER
CAREFUL READING OF THE PRESENT USER’S MANUAL.
THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE
MANUFACTURER’S LABEL.
ANY TAMPERING WITH THE INTERNAL CONNECTIONS IS PROHIBITED
AND WILL VOID THE WARRANTY.
• The unit is rated for connection to power mains with the parameters specified in the "Technical specifications” section, according to the wiring diagram.
• The connection must be made using insulated conductors (cables, wires). The actual wire cross section selection must be based on the maximum load current, maximum conductor temperature depending on the wire type, insulation, length and installation method.
• The unit should be connected to the fixed wiring system in compliance with current regulations.
Connection to power mains should be made inside the terminal box located on the fan casing, according to the wiring diagram and terminal designation. The terminal designations are shown on the label inside the terminal box. Fan electrical data is shown on the label on the fan casing.
Depending on modification, the fan motors can have no in-built thermal protection. This should be taken into account when choosing a motor starter or a contactor.
ACCESS TO THE TERMINAL BLOCK TOWER-V
ACCESS TO THE TERMINAL BLOCK TOWER-H
10
toWer-V/toWer-H www.blaubergventilatoren.de
Power supply parameters and examples of wiring diagrams depending on the unit model
Wiring diagram 1: TOWER-V/TOWER-H 190 2E, TOWER-V/TOWER-H 220 2E, TOWER-V/TOWER-H 225 2E, TOWER-V/TOWER-H 225 4E,
TOWER-V/TOWER-H 250 2E, TOWER-V/TOWER-H 250 4E, TOWER-V/TOWER-H 280 4E, TOWER-V/TOWER-H 310 2E, TOWER-V/TOWER-H 310
4E, TOWER-V/TOWER-H 355 4E, TOWER-V/TOWER-H 400 4E, TOWER-V/TOWER-H 400 6E, TOWER-V/TOWER-H 450 4E, TOWER-V/TOWER-H 450
6E. Depending on modification, the fans can have thermal contacts. Then it is necessary to use the wiring diagram 5 instead of the wiring diagram 1.
Wiring diagram 2: TOWER-V/TOWER-H 355 4D.
Wiring diagram 3: TOWER-V/TOWER-H 310 4D, TOWER-V/TOWER-H 400 4D, TOWER-V/TOWER-H 450 4D, TOWER-V/TOWER-H 500 4D,
TOWER-V/TOWER-H 560 4D.
Wiring diagram 4: TOWER-V/TOWER-H 710 6D.
Wiring diagram 5: TOWER-V/TOWER-H 500 6E, TOWER-V/TOWER-H 560 6E.
Wiring diagram 6: TOWER-V/TOWER-H 500 6D, TOWER-V/TOWER-H 560 6D, TOWER-V/TOWER-H 630 6D.
Q F
Q F Q F
L 1 L 1
L L L 1 L 1 L 2 L 2
L 2 L 2 L 3 L 3
N
N L 3 L 3
P E
P E P E
T k T K
T k T K
1 2 3
Q F Q F
Q F
L
L
P E
T
T
L
2
3 k k
1
T K
T K
L 1
L 2
L 3
L
N
P E
T k
T k
L
N
T K
T K
L 1
L 2
L 3
P E
T k
T k
U 1
V 1
W 1
W 2
U 2
V 2
T K
T K
4 5 6
WIRING DIAGRAM DESIGNATIONS:
L(x): phase; N: neutral; QF: automatic circuit breaker; PE: protective ground wire; TK: motor thermal protection contacts.
Model
TOWER-V/TOWER-H 190...250 2E
TOWER-V/TOWER-H 310 4E
TOWER-V/TOWER-H 355 4E
TOWER-V/TOWER-H 400...450 4E
TOWER-V/TOWER-H 500...560 6E
TOWER-V/TOWER-H 310...450 4D
TOWER-V/TOWER-H 500...710 6D
Recommended rated current of the automatic circuit breaker [A]
1
1.6
4
2.5
1
10
Recommended cable, nxS, where n is the number of wires, and S is the cross section in mm2
3x0.5
3x0.5
3x1.0
3x1.0
5x0.5
5x1.5
11
www.blaubergventilatoren.de
toWer-V/toWer-H
ASYNCHRONOUS ELECTRIC MOTOR STARTING METHODS
There are several methods for starting asynchronous squirrel-cage electric motors.
The most common methods are: direct-on-line (DOL), with a soft starter (SS) or with a frequency converter (FC).
Direct-on-line starting
In case of direct-on-line starting (i.e. by connecting the motor to the electric mains with a simple line contactor), the motor starting time significantly increases due to high inertia of the impeller, which, in turn, results in high in-rush starting currents in the circuit. These currents of long duration may cause voltage slumps (especially if the feed line section falls short of the requirements), which may affect load operation.
The in-rush current consumed by an electric motor in case of DOL starting is 5-8 times larger than the rated value (or even 10-14 times larger in some rare instances). It should be noted that the torque developed by the motor also significantly exceeds the rated value.
Upon energisation the motor operates as a transformer with a squirrel-cage secondary winding formed by the rotor cage with a very low resistance.
The rotor develops high induced current causing a rush of current in the feed line.
The startup torque during starting averages 0.5-1.5 of the rated torque value.
Despite such advantages as simple construction, high startup current, quick start and low cost, direct-on-line systems are suitable only in the following cases:
• the motor power is low compared to the mains power which limits the adverse effect of the rush of current
• the driven mechanism does not require gradual speed build-up or is equipped with a damping device to smooth out the inrush
• the high startup torque has no adverse effects on the operation of the driven mechanism
Soft start. SS starting.
A soft starter gradually increases the voltage supplied to the motor – from the initial to the rated value.
This starting system can be used to meet the following goals:
• limit the motor current
• regulate the torque
Regulation by limiting the current sets the maximum in-rush current equal to 300-400 % (or 250 % in some rare instances) of the rated current and reduces torque characteristics. This type of regulation is especially suited for turbomachinery such as centrifugal pumps and fans.
Regulation by variation of torque optimizes the torque during startup and reduces in-rush current in the circuit. These conditions are suitable for mechanisms with constant load resistance.
This type of soft starting may differ in the implementation pattern:
• motor start
• motor start and stop
• device bridging at the end of start sequence
• start and stop of several motors in stage circuits
Soft start. FC starting.
During the starting the FC raises the frequency from 0 Hz to the electrical mains frequency (50 or 60 Hz). As the frequency is increased gradually, the motor can be assumed to operate at its rated speed for a given frequency value. Furthermore, on the assumption that the motor runs at its rated speed the nominal torque should be immediately available whereas the current will be approximately equal to the rated value.
This starting system is used for speed control and regulation and can be used in the following cases:
• start with high-inertia load
• start with high load and limited-capacity power supply source
• optimization of electric power consumption depending on turbomachinery speed
The aforementioned starting system can be used for all types of mechanisms.
MAKE SURE THAT THE FAN IMPELLER ROTATES IN THE DIRECTION MARKED BY THE
ARROW ON THE FAN CASING.
IF NECESSARY, CHANGE THE IMPELLER ROTATION DIRECTION BY ALTERING THE PHASE
SEQUENCE ON THE ELECTRIC MOTOR TERMINALS.
12
toWer-V/toWer-H www.blaubergventilatoren.de
Problems associated with DOL starting
The problems caused by DOL starting may be divided into two groups:
1. An abrupt start causes mechanical shock, jolts in the mechanism, shock removal of free play etc.
2. A heavy start cannot be completed.
Let us review three variations of a heavy start:
1. The feed line performance is barely sufficient or insufficient to maintain the induced current.
Typical symptoms: Upon starting the circuit breakers at the system input are tripped; the lights, certain relays and contactors go off, and the supply generator shuts down.
Solution: In the best-case scenario an SS device may help reduce the in-rush current to 250 % of the motor rated current. If this is insufficient, an FC is necessary.
2. The motor cannot start the mechanism with DOL starting.
Typical symptoms: The motor fails to turn or “freezes” at certain speed which is maintained until actuation of the protection suite.
Solution: This problem may not be solved with an SS device. The motor develops insufficient shaft torque. However, this problem can be addressed by using an FC, but each case may be different.
3. The motor spins up the mechanism with authority, but fails to reach the rated rotation speed.
Typical symptoms: The input automatic circuit breaker is tripped during spin-up. This often happens with heavy-weight fans with a considerable rotation speed.
Solution: Such problems may be addressed with an SS device, but not with 100 % certainty. The closer the motor speed to the rated value during the actuation of the protective equipment, the higher the chances of success. The use of an FC in this case helps solve the problem fundamentally.
Standard switching equipment (automatic circuit breakers, contactors and motor starters) is not designed to withstand prolonged overloads normally causing the fan to shut down automatically DOL starting that continues for a long period of time.
Using switching equipment with a higher maximum current rating renders the electric motor protection system less sensitive.
As a result the switching equipment will not be able to detect motor overload in time due to a high current sensing threshold.
Such problems as mentioned above can only be addressed by utilizing a soft starter or a frequency converter to start the fan.
COMMISSIONING
THE ORGANISATION RESPONSIBLE FOR THE COMMISSIONING SHALL BE RESPONSIBLE
FOR PROPER MOTOR PHASING AND STARTING PATTERN SELECTION.
DURING STARTING THE IN-RUSH CURRENTS OF THE FAN MAY SEVERAL TIMES EXCEED
THE RATED VALUES.
SEE “ASYNCHRONOUS ELECTRIC MOTOR STARTING METHODS” IN THE “CONNECTION
TO POWER MAINS” SECTION
• After fan starting make sure that the electric motor rotates properly without undue vibration and abnormal noise.
• Make sure that the fan impeller rotates in the direction marked by the arrow on the fan casing. If necessary, change the rotation direction of the impeller by reversing the phase sequence (for a three-phase motor) or by rewiring according to the wiring diagram located inside the terminal box (for a single-phase motor).
• Make sure that the fan energy consumption complies with the value given on the equipment nameplate and check the motor for overheating.
• The phase current should be checked once the fan reaches the rated operating conditions.
• Do not switch the fan on and off several times without pauses as this may result in damage to the winding or insulation due to overheating.
In conditions of low temperatures and high humidity, in order to avoid freezing or water ingress into the duct, the unit must be operated continuously.
13
www.blaubergventilatoren.de
toWer-V/toWer-H
TECHNICAL MAINTENANCE
DISCONNECT THE UNIT FROM POWER SUPPLY BEFORE ANY MAINTENANCE
OPERATIONS!
MAKE SURE THE UNIT IS DISCONNECTED FROM POWER MAINS BEFORE REMOVING
THE PROTECTION
PRIOR TO COMMENCING ANY TECHNICAL MAINTENANCE PUT UP A PROHIBITORY
SIGN ON THE FAN STARTING PANEL:
“DO NOT SWITCH ON! MEN AT WORK!”
AVOID LIQUID SPILLS ON THE MOTOR! DO NOT USE AGGRESSIVE SOLVENTS AND
SHARP OBJECTS FOR CLEANING!
• The technical maintenance includes periodic cleaning of the surfaces from accumulated dust and dirt.
• When carrying out fan maintenance, it is necessary to partially disassemble it in order to access contaminated parts of the fan.
• The impeller blades require thorough cleaning once in 6 months.
• Use a soft dry cloth, brush or compressed air to remove dust.
• Carry out wet cleaning using warm water and a mild household detergent.
• Protect the electric motor against liquid ingress.
• Do not immerse the unit in water!
• Do not use aggressive solvents, or sharp objects as they may damage the impeller.
TOWER-V
14
toWer-V/toWer-H www.blaubergventilatoren.de
TOWER-V 190 2E, TOWER-V 220 2E, TOWER-V 225 2E, TOWER-V 225 4E, TOWER-V 250 2E, TOWER-V 250 4E, TOWER-V 280 4E,
TOWER-V 310 2E, TOWER-V 310 4E, TOWER-V 310 4D, TOWER-V 355 4E, TOWER-V 355 4D
with a hinged cover and a motor
TOWER-H
15
www.blaubergventilatoren.de
toWer-V/toWer-H
Problem
The fan will not start.
The switching equipment activates upon fan start-up.
No power supply.
TROUBLESHOOTING
Possible reasons
Jammed motor.
Elimination
Check the mains switch. Check the electrical connections according to the wiring diagram.
Carefully check the fan impeller for possible seizure and eliminate it, if necessary. If the impeller is in order, replace the electric motor.
Short circuit in the fan or the electric circuit between the fan and the switching equipment.
Eliminate the cause of a short circuit.
Excessive current consumption due to an overload in the electric mains.
Eliminate the cause of excessive current consumption.
Improper fan starting method.
Improper switching equipment.
Use a soft starter or frequency converter to start the motor
(see "Asynchronous Electric Motor Starting Methods" in the "Connection to power mains" section) .
Re-select the switching equipment in accordance with the current regulations and equipment specifications.
The installed switching equipment is of poor quality or its actual performance falls short of the rated values stated by the manufacturer.
Re-select the switching equipment by choosing a unit which successfully passed commutation and load tests and has a technical compliance certificate. The selection should be limited to the top five foreign switching equipment manufacturers.
The fan fails to reach the required rotation speed due to serious overheating of the fan motor.
Fan motor overloaded.
Improper fan starting method.
Eliminate the overload.
Use a soft starter or frequency converter to start the motor
(see “Asynchronous Electric Motor Starting Methods” in the “Connection to power mains” section) .
The fan motor runs at overload capacity with current consumption in excess of the rated value.
The fan supplies more air than expected upon motor capacity selection.
Measure network resistance. Throttle down the network
(add aerodynamic resistance to the air duct network).
The fan supplies more air than expected.
Wrong motor phasing. The impeller rotates in the opposite direction of the arrow on the fan casing.
Air ducts clogged.
The resistance values used during the ventilation network calculations are too conservative.
The cross section of air ducts increased and their number reduced during the installation.
Wrong choice of the fan.
If necessary, change the impeller rotation direction by changing the phase sequence on the electric motor terminals.
Clean the air duct or the impeller.
Check the air ducts for proper shape and cross section as well as for any dampers present.
Throttle down the network (add aerodynamic resistance to the air duct network).
Replace the fan with a unit of proper standard size.
16
toWer-V/toWer-H www.blaubergventilatoren.de
The fan supplies less air than expected.
Wrong calculation of the ventilation network and wrong selection of the fan.
The network resistance exceeds the design calculations.
Wrong direction of the impeller rotation.
Air leak through a loose air duct connection.
Impeller or air duct contamination with foreign objects or debris.
Re-calculate the network parameters and select a matching fan.
Re-arrange the ventilation network to decrease its aerodynamic resistance.
If necessary, change the impeller rotation direction by changing the phase sequence on the electric motor terminals (see the “Commissioning” section) .
Eliminate the air leak. Seal the air duct connection.
Clean the impeller or the air ducts from foreign objects or debris.
Excessive noise or vibration both inside the fan and in the circuit.
Loose screw connections.
No flexible joints between the fan and the ventilation network on the suction and discharge sides.
Check the screw connections for proper tightness.
Install flexible joints.
Loose connection of valves and dampers to the air ducts.
Impeller or air duct contamination with foreign objects or debris.
Worn bearings.
Unstable power supply, unstable motor operation.
Tighten up the fasteners of valves and dampers.
Clean the impeller or the air ducts from foreign objects or debris.
Replace the bearings.
Check the stability of power supply parameters and electric motor operation.
STORAGE AND TRANSPORTATION REGULATIONS
• Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with temperature range from +5 ˚C to +40 ˚C and relative humidity up to 70 %.
• Storage environment must not contain aggressive vapors and chemical mixtures provoking corrosion, insulation, and sealing deformation.
• Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.
• Follow the handling requirements applicable for the particular type of cargo.
• The unit can be carried in the original packaging by any mode of transport provided proper protection against precipitation and mechanical damage. The unit must be transported only in the working position.
• Avoid sharp blows, scratches, or rough handling during loading and unloading.
• Prior to the initial power-up after transportation at low temperatures, allow the unit to warm up at operating temperature for at least 3-4 hours.
17
www.blaubergventilatoren.de
toWer-V/toWer-H
MANUFACTURER’S WARRANTY
The product is in compliance with EU norms and standards on low voltage guidelines and electromagnetic compatibility. We hereby declare that the product complies with the provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU of the European
Parliament and of the Council, Low Voltage Directive (LVD) 2014/35/EU of the European Parliament and of the Council and CE-marking
Council Directive 93/68/EEC. This certificate is issued following test carried out on samples of the product referred to above.
The manufacturer hereby warrants normal operation of the unit for 24 months after the retail sale date provided the user's observance of the transportation, storage, installation, and operation regulations. Should any malfunctions occur in the course of the unit operation through the Manufacturer's fault during the guaranteed period of operation, the user is entitled to get all the faults eliminated by the manufacturer by means of warranty repair at the factory free of charge. The warranty repair includes work specific to elimination of faults in the unit operation to ensure its intended use by the user within the guaranteed period of operation. The faults are eliminated by means of replacement or repair of the unit components or a specific part of such unit component.
The warranty repair does not include:
• routine technical maintenance
• unit installation/dismantling
• unit setup
To benefit from warranty repair, the user must provide the unit, the user's manual with the purchase date stamp, and the payment paperwork certifying the purchase. The unit model must comply with the one stated in the user’s manual. Contact the Seller for warranty service.
The manufacturer’s warranty does not apply to the following cases:
• User’s failure to submit the unit with the entire delivery package as stated in the user’s manual including submission with missing component parts previously dismounted by the user.
• Mismatch of the unit model and the brand name with the information stated on the unit packaging and in the user's manual.
• User’s failure to ensure timely technical maintenance of the unit.
• External damage to the unit casing (excluding external modifications as required for installation) and internal components caused by the user.
• Redesign or engineering changes to the unit.
• Replacement and use of any assemblies, parts and components not approved by the manufacturer.
• Unit misuse.
• Violation of the unit installation regulations by the user.
• Violation of the unit control regulations by the user.
• Unit connection to power mains with a voltage different from the one stated in the user's manual.
• Unit breakdown due to voltage surges in power mains.
• Discretionary repair of the unit by the user.
• Unit repair by any persons without the manufacturer’s authorization.
• Expiration of the unit warranty period.
• Violation of the unit transportation regulations by the user.
• Violation of the unit storage regulations by the user.
• Wrongful actions against the unit committed by third parties.
• Unit breakdown due to circumstances of insuperable force (fire, flood, earthquake, war, hostilities of any kind, blockades).
• Missing seals if provided by the user’s manual.
• Failure to submit the user’s manual with the unit purchase date stamp.
• Missing payment paperwork certifying the unit purchase.
FOLLOWING THE REGULATIONS STIPULATED HEREIN WILL ENSURE A LONG AND
TROUBLE-FREE OPERATION OF THE UNIT.
USER’S WARRANTY CLAIMS SHALL BE SUBJECT TO REVIEW ONLY UPON
PRESENTATION OF THE UNIT, THE PAYMENT DOCUMENT AND THE USER’S MANUAL
WITH THE PURCHASE DATE STAMP.
18
toWer-V/toWer-H
CERTIFICATE OF ACCEPTANCE
Unit Type
Model
Serial Number
Manufacture Date
Quality Inspector’s
Stamp
Centrifugal roof fan
SELLER INFORMATION
Seller
Address
Phone Number
Purchase Date
This is to certify acceptance of the complete unit delivery with the user’s manual. The warranty terms are acknowledged and accepted.
Customer’s Signature
INSTALLATION CERTIFICATE
The _____________________________________ unit is installed pursuant to the requirements stated in the present user's manual.
Company name
Address
Phone Number
Installation
Technician’s Full Name
Installation Date: Signature:
The unit has been installed in accordance with the provisions of all the applicable local and national construction, electrical and technical codes and standards. The unit operates normally as intended by the manufacturer.
Signature:
WARRANTY CARD
Unit Type
Model
Serial Number
Manufacture Date
Purchase Date
Warranty Period
Seller
Centrifugal roof fan www.blaubergventilatoren.de
Seller’s Stamp
Installation Stamp
Seller’s Stamp
19
www.blaubergventilatoren.de
B204EN-02
İndir
Herkese açık bağlantı güncellendi
Sohbetinize giden herkese açık bağlantı güncellendi. You may view and manage your chat links after registration here.
Belge herkese açık bağlantısı
Reklam
